All local configuration variables have to be declared before they can be
used. Example:
\begin{verbatim}
- uses ROM_IMAGE_SIZE
+ uses CONFIG_ROM_IMAGE_SIZE
\end{verbatim}
\textbf{NOTE:} Only configuration variables known to the configuration
Example:
\begin{verbatim}
- default ROM_IMAGE_SIZE=0x10000
+ default CONFIG_ROM_IMAGE_SIZE=0x10000
\end{verbatim}
It is also possible to assign the value of one configuration variable to
another one, i.e.:
\begin{verbatim}
- default FALLBACK_SIZE=ROM_SIZE
+ default CONFIG_FALLBACK_SIZE=CONFIG_ROM_SIZE
\end{verbatim}
Also, simple expressions are allowed:
\begin{verbatim}
- default FALLBACK_SIZE=(ROM_SIZE - NORMAL_SIZE)
+ default CONFIG_FALLBACK_SIZE=(CONFIG_ROM_SIZE - NORMAL_SIZE)
\end{verbatim}
If an option contains a string, this string has to be protected with
\begin{verbatim}
romimage "normal"
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=0x10000
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=0x10000
option COREBOOT_EXTRA_VERSION=".0Normal"
mainboard amd/solo
payload /suse/stepan/tg3ide_
the images and the final image size:
\begin{verbatim}
- buildrom ./solo.rom ROM_SIZE "normal" "fallback"
+ buildrom ./solo.rom CONFIG_ROM_SIZE "normal" "fallback"
\end{verbatim}
\end{itemize}
Use new \textit{chip\_configure} method for configuring (nonpci)
devices. Set to \texttt{1} for all AMD64 mainboards.
-\item \begin{verbatim}MAXIMUM_CONSOLE_LOGLEVEL\end{verbatim}
+\item \begin{verbatim}CONFIG_MAXIMUM_CONSOLE_LOGLEVEL\end{verbatim}
Errors or log messages up to this level can be printed. Default is
\texttt{8}, minimum is \texttt{0}, maximum is \texttt{10}.
-\item \begin{verbatim}DEFAULT_CONSOLE_LOGLEVEL\end{verbatim}
+\item \begin{verbatim}CONFIG_DEFAULT_CONSOLE_LOGLEVEL\end{verbatim}
Console will log at this level unless changed. Default is \texttt{7},
minimum is \texttt{0}, maximum is \texttt{10}.
(don't log to serial console). This value should be set to \texttt{1}
for all AMD64 builds.
-\item \begin{verbatim}ROM_SIZE\end{verbatim}
+\item \begin{verbatim}CONFIG_ROM_SIZE\end{verbatim}
Size of final ROM image. This option has no default value.
-\item \begin{verbatim}FALLBACK_SIZE\end{verbatim}
+\item \begin{verbatim}CONFIG_FALLBACK_SIZE\end{verbatim}
Fallback image size. Defaults to \texttt{65536} bytes. \textbf{NOTE:}
This does not include the fallback payload.
-\item \begin{verbatim}HAVE_OPTION_TABLE\end{verbatim}
+\item \begin{verbatim}CONFIG_HAVE_OPTION_TABLE\end{verbatim}
Export CMOS option table. Default is \texttt{0}. Set to \texttt{1} if
your mainboard has CMOS memory and you want to use it to store
Boot image is located in ROM (as opposed to \texttt{CONFIG\_IDE\_PAYLOAD}, which
will boot from an IDE disk)
-\item \begin{verbatim}HAVE_FALLBACK_BOOT\end{verbatim}
+\item \begin{verbatim}CONFIG_HAVE_FALLBACK_BOOT\end{verbatim}
Set to \texttt{1} if fallback booting is required. Defaults to
\texttt{0}.
\begin{itemize}
-\item \begin{verbatim}USE_FALLBACK_IMAGE\end{verbatim}
+\item \begin{verbatim}CONFIG_USE_FALLBACK_IMAGE\end{verbatim}
Set to \texttt{1} to build a fallback image. Defaults to \texttt{0}
-\item \begin{verbatim}ROM_IMAGE_SIZE\end{verbatim}
+\item \begin{verbatim}CONFIG_ROM_IMAGE_SIZE\end{verbatim}
Default image size. Defaults to \texttt{65535} bytes.
\begin{verbatim}
makerule ./auto.E
- depends "$(MAINBOARD)/auto.c option_table.h ./romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ./romcc"
action "./romcc -E -mcpu=k8 -O2 -I$(TOP)/src -I. $(CPPFLAGS) \
- $(MAINBOARD)/auto.c -o $@"
+ $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- depends "$(MAINBOARD)/auto.c option_table.h ./romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ./romcc"
action "./romcc -mcpu=k8 -O2 -I$(TOP)/src -I. $(CPPFLAGS) \
- $(MAINBOARD)/auto.c -o $@"
+ $(CONFIG_MAINBOARD)/auto.c -o $@"
end
\end{verbatim}
\begin{itemize}
-\item \begin{verbatim}HAVE_HARD_RESET\end{verbatim}
+\item \begin{verbatim}CONFIG_HAVE_HARD_RESET\end{verbatim}
If set to \texttt{1}, this option defines that there is a hard reset
function for this mainboard. This option is not defined per default.
-\item \begin{verbatim}HAVE_PIRQ_TABLE\end{verbatim}
+\item \begin{verbatim}CONFIG_HAVE_PIRQ_TABLE\end{verbatim}
If set to \texttt{1}, this option defines that there is an IRQ Table for
this mainboard. This option is not defined per default.
-\item \begin{verbatim}IRQ_SLOT_COUNT\end{verbatim}
+\item \begin{verbatim}CONFIG_IRQ_SLOT_COUNT\end{verbatim}
Number of IRQ slots. This option is not defined per default.
-\item \begin{verbatim}HAVE_MP_TABLE\end{verbatim}
+\item \begin{verbatim}CONFIG_HAVE_MP_TABLE\end{verbatim}
Define this option to build an MP table (v1.4). The default is not to
build an MP table.
-\item \begin{verbatim}HAVE_OPTION_TABLE\end{verbatim}
+\item \begin{verbatim}CONFIG_HAVE_OPTION_TABLE\end{verbatim}
Define this option to export a CMOS option table. The default is not to
export a CMOS option table.
Set this option to \texttt{1} to enable IOAPIC support. This is
mandatory if you want to boot a 64bit Linux kernel on an AMD64 system.
-\item \begin{verbatim}STACK_SIZE\end{verbatim}
+\item \begin{verbatim}CONFIG_STACK_SIZE\end{verbatim}
coreboot stack size. The size of the function call stack defaults to
\texttt{0x2000} (8k).
-\item \begin{verbatim}HEAP_SIZE\end{verbatim}
+\item \begin{verbatim}CONFIG_HEAP_SIZE\end{verbatim}
coreboot heap size. The heap is used when coreboot allocates memory
with malloc(). The default heap size is \texttt{0x2000}, but AMD64 boards
generally set it to \texttt{0x4000} (16k)
-\item \begin{verbatim}XIP_ROM_BASE\end{verbatim}
+\item \begin{verbatim}CONFIG_XIP_ROM_BASE\end{verbatim}
Start address of area to cache during coreboot execution directly from
ROM.
-\item \begin{verbatim}XIP_ROM_SIZE\end{verbatim}
+\item \begin{verbatim}CONFIG_XIP_ROM_SIZE\end{verbatim}
Size of area to cache during coreboot execution directly from ROM
variables set in their \texttt{Config.lb} file:
\begin{verbatim}
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=7
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=7
\end{verbatim}
This will make coreboot look for the file \\
\begin{verbatim}
default CONFIG_SMP=1
default CONFIG_MAX_CPUS=1 # 2,4,..
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
\end{verbatim}
coreboot will then look for a function for setting up the MP table in
To enable ACPI in your coreboot build, add the following lines to your
configuration files:
\begin{verbatim}
-uses HAVE_ACPI_TABLES
+uses CONFIG_HAVE_ACPI_TABLES
[..]
-option HAVE_ACPI_TABLES=1
+option CONFIG_HAVE_ACPI_TABLES=1
\end{verbatim}
To keep Linux doing it's pci ressource allocation based on IRQ tables and MP
coreboot has to either assert an LDTSTOP or a reset to make the changes
become active. Additionally Linux can do a firmware reset, if coreboot
provides the needed infrastructure. To use this capability, define the
-option \texttt{HAVE\_HARD\_RESET} and add an object file specifying the
+option \texttt{HAVE\_HARD\CONFIG_RESET} and add an object file specifying the
reset code in your mainboard specific configuration file
\texttt{coreboot-v2/src/mainboard/$<$vendor$>$/$<$mainboard$>$/Config.lb}:
\begin{verbatim}
- default HAVE_HARD_RESET=1
+ default CONFIG_HAVE_HARD_RESET=1
object reset.o
\end{verbatim}
There are two big additions to the build process and, furthermore, more than two new CONFIG variables to control them.
\begin{itemize}
-\item \begin{verbatim}USE_DCACHE_RAM\end{verbatim}
+\item \begin{verbatim}CONFIG_USE_DCACHE_RAM\end{verbatim}
Set to \texttt{1} to use Cache As Ram (CAR). Defaults to \texttt{0}
ROMCC images are so-called because C code for the ROM part is compiled with romcc. romcc is an optimizing C compiler which compiles one, and only
one file; to get more than one file, one must include the C code via include statements. The main ROM code .c file is usually called auto.c.
\subsubsection{How it is built}
-Romcc compiles auto.c to produce auto.inc. auto.inc is included in the main crt0.S, which is then preprocessed to produce crt0.s. The inclusion of files into crt0.S is controlled by the CRT0\_INCLUDES variable. crt0.s is then assembled.
+Romcc compiles auto.c to produce auto.inc. auto.inc is included in the main crt0.S, which is then preprocessed to produce crt0.s. The inclusion of files into crt0.S is controlled by the CONFIG_CRT0\_INCLUDES variable. crt0.s is then assembled.
File for the ram part are compiled in a conventional manner.
\begin{itemize}
\item PAYLOAD\_SIZE. Each image may have a different payload size.
-\item \_ROMBASE Each image must have a different base in rom.
-\item \_RESET Unclear what this is used for.
+\item \CONFIG_ROMBASE Each image must have a different base in rom.
+\item \CONFIG_RESET Unclear what this is used for.
\item \_EXCEPTION\_VECTORS where an optional IDT might go.
\item USE\_OPTION\_TABLE if set, an option table section will be linked in.
\item CONFIG\_ROM\_PAYLOAD\_START This is the soon-to-be-deprecated way of locating a payload. cbfs eliminates this.
);
fallback_image:
-#if HAVE_FAILOVER_BOOT==1
+#if CONFIG_HAVE_FAILOVER_BOOT==1
__asm__ volatile ("jmp __fallback_image"
: /* outputs */
: "a" (bist), "b" (cpu_init_detectedx) /* inputs */
How does the fallback image get the symbol for normal entry? Via magic in the ldscript.ld -- remember, the images are not linked to each other.
Finally, we can see this in the Config.lb for most mainboards:
\begin{verbatim}
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
The fallback and normal builds are the same. The target config has a new clause that looks like this:
\begin{verbatim}
romimage "failover"
- option USE_FAILOVER_IMAGE=1
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=FAILOVER_SIZE
- option XIP_ROM_SIZE=FAILOVER_SIZE
+ option CONFIG_USE_FAILOVER_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=CONFIG_FAILOVER_SIZE
+ option CONFIG_XIP_ROM_SIZE=CONFIG_FAILOVER_SIZE
option COREBOOT_EXTRA_VERSION="\$(shell cat ../../VERSION)\_Failover"
end
\end{verbatim}
target x
# over-ride the default rom size in the mainboard file
-option ROM_SIZE=1024*1024
+option CONFIG_ROM_SIZE=1024*1024
mainboard amd/solo
end
arch i386 end
cpu k8 end
#
-option DEBUG=1
-default USE_FALLBACK_IMAGE=1
+option CONFIG_DEBUG=1
+default CONFIG_USE_FALLBACK_IMAGE=1
option A=(1+2)
option B=0xa
#
###
### Build our reset vector (This is where linuxBIOS is entered)
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/i386/reset16.inc
ldscript cpu/i386/reset16.lds
else
.
.
.
-if USE_FALLBACK_IMAGE mainboardinit arch/i386/lib/noop_failover.inc end
+if CONFIG_USE_FALLBACK_IMAGE mainboardinit arch/i386/lib/noop_failover.inc end
#
###
### Romcc output
###
-#makerule ./failover.E dep "$(MAINBOARD)/failover.c" act "$(CPP) -I$(TOP)/src $(CPPFLAGS) $(MAINBOARD)/failover.c > ./failever.E"
+#makerule ./failover.E dep "$(CONFIG_MAINBOARD)/failover.c" act "$(CPP) -I$(TOP)/src $(CPPFLAGS) $(CONFIG_MAINBOARD)/failover.c > ./failever.E"
#makerule ./failover.inc dep "./romcc ./failover.E" act "./romcc -O ./failover.E > failover.inc"
#mainboardinit ./failover.inc
-makerule ./auto.E dep "$(MAINBOARD)/auto.c" act "$(CPP) -I$(TOP)/src -$(ROMCCPPFLAGS) $(CPPFLAGS) $(MAINBOARD)/auto.c > ./auto.E"
+makerule ./auto.E dep "$(CONFIG_MAINBOARD)/auto.c" act "$(CPP) -I$(TOP)/src -$(ROMCCPPFLAGS) $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c > ./auto.E"
makerule ./auto.inc dep "./romcc ./auto.E" act "./romcc -O ./auto.E > auto.inc"
mainboardinit ./auto.inc
#
##object mainboard.o
driver mainboard.o
object static_devices.o
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
### Location of the DIMM EEPROMS on the SMBUS
### This is fixed into a narrow range by the DIMM package standard.
###
#
### The linuxBIOS bootloader.
###
-option PAYLOAD_SIZE = (ROM_SECTION_SIZE - ROM_IMAGE_SIZE)
-option CONFIG_ROM_PAYLOAD_START = (0xffffffff - ROM_SIZE + ROM_SECTION_OFFSET + 1)
+option CONFIG_PAYLOAD_SIZE = (CONFIG_ROM_SECTION_SIZE - CONFIG_ROM_IMAGE_SIZE)
+option CONFIG_ROM_PAYLOAD_START = (0xffffffff - CONFIG_ROM_SIZE + CONFIG_ROM_SECTION_OFFSET + 1)
#
\end{verbatim}
\begin{verbatim}
TOP:=/home/rminnich/src/yapps2/freebios2
TARGET_DIR:=x
-export MAINBOARD:=/home/rminnich/src/yapps2/freebios2/src/mainboard/amd/solo
-export ARCH:=i386
-export _RAMBASE:=0x4000
-export ROM_IMAGE_SIZE:=65535
-export PAYLOAD_SIZE:=131073
+export CONFIG_MAINBOARD:=/home/rminnich/src/yapps2/freebios2/src/mainboard/amd/solo
+export CONFIG_ARCH:=i386
+export CONFIG_RAMBASE:=0x4000
+export CONFIG_ROM_IMAGE_SIZE:=65535
+export CONFIG_PAYLOAD_SIZE:=131073
export CONFIG_MAX_CPUS:=1
-export HEAP_SIZE:=8192
-export STACK_SIZE:=8192
-export MEMORY_HOLE:=0
+export CONFIG_HEAP_SIZE:=8192
+export CONFIG_STACK_SIZE:=8192
+export CONFIG_MEMORY_HOLE:=0
export COREBOOT_VERSION:=1.1.0
-export CC:=$(CROSS_COMPILE)gcc
+export CC:=$(CONFIG_CROSS_COMPILE)gcc
\end{verbatim}
uses CONFIG_SMP
uses CONFIG_PRECOMPRESSED_PAYLOAD
uses CONFIG_USE_INIT
-uses HAVE_FAILOVER_BOOT
-uses USE_FAILOVER_IMAGE
-uses USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FAILOVER_BOOT
+uses CONFIG_USE_FAILOVER_IMAGE
+uses CONFIG_USE_FALLBACK_IMAGE
init init/crt0.S.lb
if CONFIG_CBFS
- if USE_FAILOVER_IMAGE
+ if CONFIG_USE_FAILOVER_IMAGE
else
initobject /src/lib/cbfs.o
initobject /src/console/vsprintf.o
end
end
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
ldscript init/ldscript_failover.lb
else
if CONFIG_CBFS
end
else
if CONFIG_CBFS
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
ldscript init/ldscript_fallback_cbfs.lb
else
ldscript init/ldscript_cbfs.lb
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
ldscript init/ldscript_fallback.lb
else
ldscript init/ldscript.lb
makerule nrv2b
depends "$(TOP)/util/nrv2b/nrv2b.c"
- action "$(HOSTCC) -O2 -DENCODE -DDECODE -DMAIN -DVERBOSE -DNDEBUG -DBITSIZE=32 -DENDIAN=0 $< -o $@"
+ action "$(CONFIG_HOSTCC) -O2 -DENCODE -DDECODE -DMAIN -DVERBOSE -DNDEBUG -DBITSIZE=32 -DENDIAN=0 $< -o $@"
end
makerule payload
makedefine PAYLOAD-1:=payload
end
-if USE_FAILOVER_IMAGE
+if CONFIG_USE_FAILOVER_IMAGE
makedefine COREBOOT_APC:=
makedefine COREBOOT_RAM_ROM:=
else
makerule coreboot.rom
depends "coreboot.strip buildrom $(PAYLOAD-1)"
- action "PAYLOAD=$(PAYLOAD-1); if [ $(CONFIG_CBFS) -eq 1 ]; then PAYLOAD=/dev/null; touch cbfs-support; fi; ./buildrom $< $@ $$PAYLOAD $(ROM_IMAGE_SIZE) $(ROM_SECTION_SIZE)"
+ action "PAYLOAD=$(PAYLOAD-1); if [ $(CONFIG_CBFS) -eq 1 ]; then PAYLOAD=/dev/null; touch cbfs-support; fi; ./buildrom $< $@ $$PAYLOAD $(CONFIG_ROM_IMAGE_SIZE) $(CONFIG_ROM_SECTION_SIZE)"
action "if [ $(CONFIG_COMPRESSED_PAYLOAD_LZMA) -eq 1 -a $(CONFIG_CBFS) -eq 1 ]; then echo l > cbfs-support; fi"
end
end
makerule crt0.S
- depends "$(CRT0)"
+ depends "$(CONFIG_CRT0)"
action "cp $< $@"
end
makerule init.o
depends "$(INIT-OBJECTS)"
action "$(LD) -melf_i386 -r -o init.pre.o $(INIT-OBJECTS)"
- action "$(OBJCOPY) --rename-section .text=.init.text --rename-section .data=.init.data --rename-section .rodata=.init.rodata --rename-section .rodata.str1.1=.init.rodata.str1.1 init.pre.o init.o"
+ action "$(CONFIG_OBJCOPY) --rename-section .text=.init.text --rename-section .data=.init.data --rename-section .rodata=.init.rodata --rename-section .rodata.str1.1=.init.rodata.str1.1 init.pre.o init.o"
end
makerule coreboot
depends "crt0.o init.o $(COREBOOT_APC) $(COREBOOT_RAM_ROM) ldscript.ld"
action "$(CC) -nostdlib -nostartfiles -static -o $@ -T ldscript.ld crt0.o init.o"
- action "$(CROSS_COMPILE)nm -n coreboot | sort > coreboot.map"
+ action "$(CONFIG_CROSS_COMPILE)nm -n coreboot | sort > coreboot.map"
end
end
-uses HAVE_PIRQ_TABLE
-uses HAVE_ACPI_TABLES
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_HAVE_ACPI_TABLES
uses CONFIG_MULTIBOOT
-uses HAVE_ACPI_RESUME
+uses CONFIG_HAVE_ACPI_RESUME
object boot.o
object coreboot_table.o
object multiboot.o
end
object tables.o
-if HAVE_PIRQ_TABLE
+if CONFIG_HAVE_PIRQ_TABLE
object pirq_routing.o
end
-if HAVE_ACPI_TABLES
+if CONFIG_HAVE_ACPI_TABLES
object acpi.o
object acpigen.o
-if HAVE_ACPI_RESUME
+if CONFIG_HAVE_ACPI_RESUME
object wakeup.S
end
end
rsdp->ext_checksum = acpi_checksum((void *)rsdp, sizeof(acpi_rsdp_t));
}
-#if HAVE_ACPI_RESUME == 1
+#if CONFIG_HAVE_ACPI_RESUME == 1
void suspend_resume(void)
{
void *wake_vec;
#if 0
-#if MEM_TRAIN_SEQ != 0
- #error "So far it works on AMD and MEM_TRAIN_SEQ == 0"
+#if CONFIG_MEM_TRAIN_SEQ != 0
+ #error "So far it works on AMD and CONFIG_MEM_TRAIN_SEQ == 0"
#endif
-#if _RAMBASE < 0x1F00000
- #error "For ACPI RESUME you need to have _RAMBASE at least 31MB"
+#if CONFIG_RAMBASE < 0x1F00000
+ #error "For ACPI RESUME you need to have CONFIG_RAMBASE at least 31MB"
#error "Chipset support (S3_NVRAM_EARLY and ACPI_IS_WAKEUP_EARLY functions and memory ctrl)"
#error "And coreboot memory reserved in mainboard.c"
#endif
struct lb_serial *lb_serial(struct lb_header *header)
{
-#if defined(TTYS0_BASE)
+#if defined(CONFIG_TTYS0_BASE)
struct lb_record *rec;
struct lb_serial *serial;
rec = lb_new_record(header);
serial = (struct lb_serial *)rec;
serial->tag = LB_TAG_SERIAL;
serial->size = sizeof(*serial);
- serial->ioport = TTYS0_BASE;
- serial->baud = TTYS0_BAUD;
+ serial->ioport = CONFIG_TTYS0_BASE;
+ serial->baud = CONFIG_TTYS0_BAUD;
return serial;
#else
return header;
cmos_checksum->size = (sizeof(*cmos_checksum));
- cmos_checksum->range_start = LB_CKS_RANGE_START * 8;
- cmos_checksum->range_end = ( LB_CKS_RANGE_END * 8 ) + 7;
- cmos_checksum->location = LB_CKS_LOC * 8;
+ cmos_checksum->range_start = CONFIG_LB_CKS_RANGE_START * 8;
+ cmos_checksum->range_end = ( CONFIG_LB_CKS_RANGE_END * 8 ) + 7;
+ cmos_checksum->location = CONFIG_LB_CKS_LOC * 8;
cmos_checksum->type = CHECKSUM_PCBIOS;
return cmos_checksum;
return mem;
}
-#if HAVE_HIGH_TABLES == 1
+#if CONFIG_HAVE_HIGH_TABLES == 1
extern uint64_t high_tables_base, high_tables_size;
#endif
struct lb_header *head;
struct lb_memory *mem;
-#if HAVE_HIGH_TABLES == 1
+#if CONFIG_HAVE_HIGH_TABLES == 1
printk_debug("Writing high table forward entry at 0x%08lx\n",
low_table_end);
head = lb_table_init(low_table_end);
rom_table_end &= ~0xffff;
printk_debug("0x%08lx \n", rom_table_end);
-#if (HAVE_OPTION_TABLE == 1)
+#if (CONFIG_HAVE_OPTION_TABLE == 1)
{
struct lb_record *rec_dest, *rec_src;
/* Write the option config table... */
lb_add_memory_range(mem, LB_MEM_TABLE,
rom_table_start, rom_table_end-rom_table_start);
-#if HAVE_HIGH_TABLES == 1
+#if CONFIG_HAVE_HIGH_TABLES == 1
printk_debug("Adding high table area\n");
lb_add_memory_range(mem, LB_MEM_TABLE,
high_tables_base, high_tables_size);
#endif
-#if (HAVE_MAINBOARD_RESOURCES == 1)
+#if (CONFIG_HAVE_MAINBOARD_RESOURCES == 1)
add_mainboard_resources(mem);
#endif
#include <string.h>
#include <device/pci.h>
-#if (DEBUG==1 && HAVE_PIRQ_TABLE==1)
+#if (CONFIG_DEBUG==1 && CONFIG_HAVE_PIRQ_TABLE==1)
static void check_pirq_routing_table(struct irq_routing_table *rt)
{
uint8_t *addr = (uint8_t *)rt;
printk_info("Checking Interrupt Routing Table consistency...\n");
-#if defined(IRQ_SLOT_COUNT)
+#if defined(CONFIG_IRQ_SLOT_COUNT)
if (sizeof(struct irq_routing_table) != rt->size) {
printk_warning("Inconsistent Interrupt Routing Table size (0x%x/0x%x).\n",
sizeof(struct irq_routing_table),
#define verify_copy_pirq_routing_table(addr)
#endif
-#if HAVE_PIRQ_TABLE==1
+#if CONFIG_HAVE_PIRQ_TABLE==1
unsigned long copy_pirq_routing_table(unsigned long addr)
{
/* Align the table to be 16 byte aligned. */
}
#endif
-#if (PIRQ_ROUTE==1 && HAVE_PIRQ_TABLE==1)
+#if (CONFIG_PIRQ_ROUTE==1 && CONFIG_HAVE_PIRQ_TABLE==1)
void pirq_routing_irqs(unsigned long addr)
{
int i, j, k, num_entries;
post_code(0x9a);
/* Write ACPI tables to F segment and high tables area */
-#if HAVE_ACPI_TABLES == 1
+#if CONFIG_HAVE_ACPI_TABLES == 1
if (high_tables_base) {
unsigned long acpi_start = high_table_end;
rom_table_end = ALIGN(rom_table_end, 16);
#endif
post_code(0x9b);
-#if HAVE_MP_TABLE == 1
+#if CONFIG_HAVE_MP_TABLE == 1
/* The smp table must be in 0-1K, 639K-640K, or 960K-1M */
rom_table_end = write_smp_table(rom_table_end);
rom_table_end = ALIGN(rom_table_end, 1024);
high_table_end = write_smp_table(high_table_end);
high_table_end = ALIGN(high_table_end, 1024);
}
-#endif /* HAVE_MP_TABLE */
+#endif /* CONFIG_HAVE_MP_TABLE */
post_code(0x9c);
#ifndef __ASM_ACPI_H
#define __ASM_ACPI_H
-#if HAVE_ACPI_TABLES==1
+#if CONFIG_HAVE_ACPI_TABLES==1
#include <stdint.h>
-#if HAVE_ACPI_RESUME
+#if CONFIG_HAVE_ACPI_RESUME
/* 0 = S0, 1 = S1 ...*/
extern u8 acpi_slp_type;
#endif
/* RSDT */
typedef struct acpi_rsdt {
struct acpi_table_header header;
- u32 entry[7+ACPI_SSDTX_NUM+CONFIG_MAX_CPUS]; /* MCONFIG, HPET, FADT, SRAT, SLIT, MADT(APIC), SSDT, SSDTX, and SSDT for CPU pstate*/
+ u32 entry[7+CONFIG_ACPI_SSDTX_NUM+CONFIG_MAX_CPUS]; /* MCONFIG, HPET, FADT, SRAT, SLIT, MADT(APIC), SSDT, SSDTX, and SSDT for CPU pstate*/
} __attribute__ ((packed)) acpi_rsdt_t;
/* XSDT */
typedef struct acpi_xsdt {
struct acpi_table_header header;
- u64 entry[6+ACPI_SSDTX_NUM];
+ u64 entry[6+CONFIG_ACPI_SSDTX_NUM];
} __attribute__ ((packed)) acpi_xsdt_t;
/* HPET TIMERS */
void acpi_write_rsdt(acpi_rsdt_t *rsdt);
void acpi_write_rsdp(acpi_rsdp_t *rsdp, acpi_rsdt_t *rsdt);
-#if HAVE_ACPI_RESUME
+#if CONFIG_HAVE_ACPI_RESUME
void suspend_resume(void);
void *acpi_find_wakeup_vector(void);
void *acpi_get_wakeup_rsdp(void);
#define IO_APIC_ADDR 0xfec00000UL
-#else // HAVE_ACPI_TABLES
+#else // CONFIG_HAVE_ACPI_TABLES
#define write_acpi_tables(start) (start)
__asm__("andl %%esp,%0; "
"orl %2, %0 "
:"=r" (ci)
- : "0" (~(STACK_SIZE - 1)),
- "r" (STACK_SIZE - sizeof(struct cpu_info))
+ : "0" (~(CONFIG_STACK_SIZE - 1)),
+ "r" (CONFIG_STACK_SIZE - sizeof(struct cpu_info))
);
return ci;
}
extern const struct pci_bus_operations pci_cf8_conf1;
extern const struct pci_bus_operations pci_cf8_conf2;
-#if MMCONF_SUPPORT==1
+#if CONFIG_MMCONF_SUPPORT==1
extern const struct pci_bus_operations pci_ops_mmconf;
#endif
#define PCI_CONF_REG_INDEX 0xcf8
#define PCI_CONF_REG_DATA 0xcfc
-#if PCI_IO_CFG_EXT == 0
+#if CONFIG_PCI_IO_CFG_EXT == 0
#define CONFIG_ADDR(bus,devfn,where) (((bus) << 16) | ((devfn) << 8) | (where))
#else
#define CONFIG_ADDR(bus,devfn,where) (((bus) << 16) | ((devfn) << 8) | (where & 0xff) | ((where & 0xf00)<<16) )
uint8_t rfu;
} __attribute__((packed));
-#if defined(IRQ_SLOT_COUNT)
-#define IRQ_SLOTS_COUNT IRQ_SLOT_COUNT
+#if defined(CONFIG_IRQ_SLOT_COUNT)
+#define IRQ_SLOTS_COUNT CONFIG_IRQ_SLOT_COUNT
#elif (__GNUC__ < 3)
#define IRQ_SLOTS_COUNT 1
#else
extern const struct irq_routing_table intel_irq_routing_table;
-#if HAVE_PIRQ_TABLE==1
+#if CONFIG_HAVE_PIRQ_TABLE==1
unsigned long copy_pirq_routing_table(unsigned long start);
unsigned long write_pirq_routing_table(unsigned long start);
-#if PIRQ_ROUTE==1
+#if CONFIG_PIRQ_ROUTE==1
void pirq_routing_irqs(unsigned long start);
void pirq_assign_irqs(const unsigned char pIntAtoD[4]);
#else
*((volatile uint32_t *)(addr)) = value;
}
-#if MMCONF_SUPPORT
+#if CONFIG_MMCONF_SUPPORT
#include <arch/mmio_conf.h>
static inline __attribute__((always_inline)) uint8_t pci_io_read_config8(device_t dev, unsigned where)
{
unsigned addr;
-#if PCI_IO_CFG_EXT == 0
+#if CONFIG_PCI_IO_CFG_EXT == 0
addr = (dev>>4) | where;
#else
addr = (dev>>4) | (where & 0xff) | ((where & 0xf00)<<16); //seg == 0
return inb(0xCFC + (addr & 3));
}
-#if MMCONF_SUPPORT
+#if CONFIG_MMCONF_SUPPORT
static inline __attribute__((always_inline)) uint8_t pci_mmio_read_config8(device_t dev, unsigned where)
{
unsigned addr;
- addr = MMCONF_BASE_ADDRESS | dev | where;
+ addr = CONFIG_MMCONF_BASE_ADDRESS | dev | where;
return read8x(addr);
}
#endif
static inline __attribute__((always_inline)) uint8_t pci_read_config8(device_t dev, unsigned where)
{
-#if MMCONF_SUPPORT_DEFAULT
+#if CONFIG_MMCONF_SUPPORT_DEFAULT
return pci_mmio_read_config8(dev, where);
#else
return pci_io_read_config8(dev, where);
static inline __attribute__((always_inline)) uint16_t pci_io_read_config16(device_t dev, unsigned where)
{
unsigned addr;
-#if PCI_IO_CFG_EXT == 0
+#if CONFIG_PCI_IO_CFG_EXT == 0
addr = (dev>>4) | where;
#else
addr = (dev>>4) | (where & 0xff) | ((where & 0xf00)<<16);
return inw(0xCFC + (addr & 2));
}
-#if MMCONF_SUPPORT
+#if CONFIG_MMCONF_SUPPORT
static inline __attribute__((always_inline)) uint16_t pci_mmio_read_config16(device_t dev, unsigned where)
{
unsigned addr;
- addr = MMCONF_BASE_ADDRESS | dev | where;
+ addr = CONFIG_MMCONF_BASE_ADDRESS | dev | where;
return read16x(addr);
}
#endif
static inline __attribute__((always_inline)) uint16_t pci_read_config16(device_t dev, unsigned where)
{
-#if MMCONF_SUPPORT_DEFAULT
+#if CONFIG_MMCONF_SUPPORT_DEFAULT
return pci_mmio_read_config16(dev, where);
#else
return pci_io_read_config16(dev, where);
static inline __attribute__((always_inline)) uint32_t pci_io_read_config32(device_t dev, unsigned where)
{
unsigned addr;
-#if PCI_IO_CFG_EXT == 0
+#if CONFIG_PCI_IO_CFG_EXT == 0
addr = (dev>>4) | where;
#else
addr = (dev>>4) | (where & 0xff) | ((where & 0xf00)<<16);
return inl(0xCFC);
}
-#if MMCONF_SUPPORT
+#if CONFIG_MMCONF_SUPPORT
static inline __attribute__((always_inline)) uint32_t pci_mmio_read_config32(device_t dev, unsigned where)
{
unsigned addr;
- addr = MMCONF_BASE_ADDRESS | dev | where;
+ addr = CONFIG_MMCONF_BASE_ADDRESS | dev | where;
return read32x(addr);
}
#endif
static inline __attribute__((always_inline)) uint32_t pci_read_config32(device_t dev, unsigned where)
{
-#if MMCONF_SUPPORT_DEFAULT
+#if CONFIG_MMCONF_SUPPORT_DEFAULT
return pci_mmio_read_config32(dev, where);
#else
return pci_io_read_config32(dev, where);
static inline __attribute__((always_inline)) void pci_io_write_config8(device_t dev, unsigned where, uint8_t value)
{
unsigned addr;
-#if PCI_IO_CFG_EXT == 0
+#if CONFIG_PCI_IO_CFG_EXT == 0
addr = (dev>>4) | where;
#else
addr = (dev>>4) | (where & 0xff) | ((where & 0xf00)<<16);
outb(value, 0xCFC + (addr & 3));
}
-#if MMCONF_SUPPORT
+#if CONFIG_MMCONF_SUPPORT
static inline __attribute__((always_inline)) void pci_mmio_write_config8(device_t dev, unsigned where, uint8_t value)
{
unsigned addr;
- addr = MMCONF_BASE_ADDRESS | dev | where;
+ addr = CONFIG_MMCONF_BASE_ADDRESS | dev | where;
write8x(addr, value);
}
#endif
static inline __attribute__((always_inline)) void pci_write_config8(device_t dev, unsigned where, uint8_t value)
{
-#if MMCONF_SUPPORT_DEFAULT
+#if CONFIG_MMCONF_SUPPORT_DEFAULT
pci_mmio_write_config8(dev, where, value);
#else
pci_io_write_config8(dev, where, value);
static inline __attribute__((always_inline)) void pci_io_write_config16(device_t dev, unsigned where, uint16_t value)
{
unsigned addr;
-#if PCI_IO_CFG_EXT == 0
+#if CONFIG_PCI_IO_CFG_EXT == 0
addr = (dev>>4) | where;
#else
addr = (dev>>4) | (where & 0xff) | ((where & 0xf00)<<16);
outw(value, 0xCFC + (addr & 2));
}
-#if MMCONF_SUPPORT
+#if CONFIG_MMCONF_SUPPORT
static inline __attribute__((always_inline)) void pci_mmio_write_config16(device_t dev, unsigned where, uint16_t value)
{
unsigned addr;
- addr = MMCONF_BASE_ADDRESS | dev | where;
+ addr = CONFIG_MMCONF_BASE_ADDRESS | dev | where;
write16x(addr, value);
}
#endif
static inline __attribute__((always_inline)) void pci_write_config16(device_t dev, unsigned where, uint16_t value)
{
-#if MMCONF_SUPPORT_DEFAULT
+#if CONFIG_MMCONF_SUPPORT_DEFAULT
pci_mmio_write_config16(dev, where, value);
#else
pci_io_write_config16(dev, where, value);
static inline __attribute__((always_inline)) void pci_io_write_config32(device_t dev, unsigned where, uint32_t value)
{
unsigned addr;
-#if PCI_IO_CFG_EXT == 0
+#if CONFIG_PCI_IO_CFG_EXT == 0
addr = (dev>>4) | where;
#else
addr = (dev>>4) | (where & 0xff) | ((where & 0xf00)<<16);
outl(value, 0xCFC);
}
-#if MMCONF_SUPPORT
+#if CONFIG_MMCONF_SUPPORT
static inline __attribute__((always_inline)) void pci_mmio_write_config32(device_t dev, unsigned where, uint32_t value)
{
unsigned addr;
- addr = MMCONF_BASE_ADDRESS | dev | where;
+ addr = CONFIG_MMCONF_BASE_ADDRESS | dev | where;
write32x(addr, value);
}
#endif
static inline __attribute__((always_inline)) void pci_write_config32(device_t dev, unsigned where, uint32_t value)
{
-#if MMCONF_SUPPORT_DEFAULT
+#if CONFIG_MMCONF_SUPPORT_DEFAULT
pci_mmio_write_config32(dev, where, value);
#else
pci_io_write_config32(dev, where, value);
static device_t pci_locate_device(unsigned pci_id, device_t dev)
{
- for(; dev <= PCI_DEV(255|(((1<<PCI_BUS_SEGN_BITS)-1)<<8), 31, 7); dev += PCI_DEV(0,0,1)) {
+ for(; dev <= PCI_DEV(255|(((1<<CONFIG_PCI_BUS_SEGN_BITS)-1)<<8), 31, 7); dev += PCI_DEV(0,0,1)) {
unsigned int id;
id = pci_read_config32(dev, 0);
if (id == pci_id) {
* the other is very similar to the AMD CAR, except remove amd specific msr
*/
-#define CacheSize DCACHE_RAM_SIZE
-#define CacheBase DCACHE_RAM_BASE
+#define CacheSize CONFIG_DCACHE_RAM_SIZE
+#define CacheBase CONFIG_DCACHE_RAM_BASE
#include <cpu/x86/mtrr.h>
*/
movl $0x202, %ecx
xorl %edx, %edx
- movl $(XIP_ROM_BASE | MTRR_TYPE_WRBACK), %eax
+ movl $(CONFIG_XIP_ROM_BASE | MTRR_TYPE_WRBACK), %eax
wrmsr
movl $0x203, %ecx
movl $0x0000000f, %edx
- movl $(~(XIP_ROM_SIZE - 1) | 0x800), %eax
+ movl $(~(CONFIG_XIP_ROM_SIZE - 1) | 0x800), %eax
wrmsr
-#endif /* XIP_ROM_SIZE && XIP_ROM_BASE */
+#endif /* CONFIG_XIP_ROM_SIZE && CONFIG_XIP_ROM_BASE */
/* enable cache */
movl %cr0, %eax
#include "crt0_includes.h"
-#if USE_DCACHE_RAM == 0
+#if CONFIG_USE_DCACHE_RAM == 0
#ifndef CONSOLE_DEBUG_TX_STRING
/* uses: esp, ebx, ax, dx */
# define __CRT_CONSOLE_TX_STRING(string) \
mov string, %ebx ; \
CALLSP(crt_console_tx_string)
-# if defined(TTYS0_BASE) && (ASM_CONSOLE_LOGLEVEL > BIOS_DEBUG)
+# if defined(CONFIG_TTYS0_BASE) && (ASM_CONSOLE_LOGLEVEL > BIOS_DEBUG)
# define CONSOLE_DEBUG_TX_STRING(string) __CRT_CONSOLE_TX_STRING(string)
# else
# define CONSOLE_DEBUG_TX_STRING(string)
RETSP
9:
/* Base Address */
-#ifndef TTYS0_BASE
-#define TTYS0_BASE 0x3f8
+#ifndef CONFIG_TTYS0_BASE
+#define CONFIG_TTYS0_BASE 0x3f8
#endif
/* Data */
-#define TTYS0_RBR (TTYS0_BASE+0x00)
+#define TTYS0_RBR (CONFIG_TTYS0_BASE+0x00)
/* Control */
#define TTYS0_TBR TTYS0_RBR
-#define TTYS0_IER (TTYS0_BASE+0x01)
-#define TTYS0_IIR (TTYS0_BASE+0x02)
+#define TTYS0_IER (CONFIG_TTYS0_BASE+0x01)
+#define TTYS0_IIR (CONFIG_TTYS0_BASE+0x02)
#define TTYS0_FCR TTYS0_IIR
-#define TTYS0_LCR (TTYS0_BASE+0x03)
-#define TTYS0_MCR (TTYS0_BASE+0x04)
+#define TTYS0_LCR (CONFIG_TTYS0_BASE+0x03)
+#define TTYS0_MCR (CONFIG_TTYS0_BASE+0x04)
#define TTYS0_DLL TTYS0_RBR
#define TTYS0_DLM TTYS0_IER
/* Status */
-#define TTYS0_LSR (TTYS0_BASE+0x05)
-#define TTYS0_MSR (TTYS0_BASE+0x06)
-#define TTYS0_SCR (TTYS0_BASE+0x07)
+#define TTYS0_LSR (CONFIG_TTYS0_BASE+0x05)
+#define TTYS0_MSR (CONFIG_TTYS0_BASE+0x06)
+#define TTYS0_SCR (CONFIG_TTYS0_BASE+0x07)
mov %al, %ah
10: mov $TTYS0_LSR, %dx
str_copying_to_ram: .string "Copying coreboot to RAM.\r\n"
#endif
#if CONFIG_CBFS
-# if USE_FALLBACK_IMAGE == 1
+# if CONFIG_USE_FALLBACK_IMAGE == 1
str_coreboot_ram_name: .string "fallback/coreboot_ram"
# else
str_coreboot_ram_name: .string "normal/coreboot_ram"
#endif /* ASM_CONSOLE_LOGLEVEL > BIOS_DEBUG */
-#endif /* USE_DCACHE_RAM */
+#endif /* CONFIG_USE_DCACHE_RAM */
/*
* Memory map:
*
- * _RAMBASE
+ * CONFIG_RAMBASE
* : data segment
* : bss segment
* : heap
* : stack
- * _ROMBASE
+ * CONFIG_ROMBASE
* : coreboot text
* : readonly text
*/
INPUT(coreboot_ram.rom)
SECTIONS
{
- . = _ROMBASE;
+ . = CONFIG_ROMBASE;
.ram . : {
_ram = . ;
_lrom = LOADADDR(.rom);
_elrom = LOADADDR(.rom) + SIZEOF(.rom);
- _iseg = _RAMBASE;
+ _iseg = CONFIG_RAMBASE;
_eiseg = _iseg + SIZEOF(.ram);
_liseg = _ram;
_eliseg = _eram;
coreboot_apc.rom(*)
_eapcrom = .;
}
- _iseg_apc = DCACHE_RAM_BASE;
+ _iseg_apc = CONFIG_DCACHE_RAM_BASE;
_eiseg_apc = _iseg_apc + SIZEOF(.apcrom);
_liseg_apc = _apcrom;
_eliseg_apc = _eapcrom;
/*
* Memory map:
*
- * _RAMBASE
+ * CONFIG_RAMBASE
* : data segment
* : bss segment
* : heap
* : stack
- * _ROMBASE
+ * CONFIG_ROMBASE
* : coreboot text
* : readonly text
*/
TARGET(binary)
SECTIONS
{
- . = _ROMBASE;
+ . = CONFIG_ROMBASE;
/* This section might be better named .setup */
.rom . : {
/*
* Memory map:
*
- * _RAMBASE
+ * CONFIG_RAMBASE
* : data segment
* : bss segment
* : heap
* : stack
- * _ROMBASE
+ * CONFIG_ROMBASE
* : coreboot text
* : readonly text
*/
TARGET(binary)
SECTIONS
{
- . = _ROMBASE;
+ . = CONFIG_ROMBASE;
/* This section might be better named .setup */
.rom . : {
/*
* Memory map:
*
- * _RAMBASE
+ * CONFIG_RAMBASE
* : data segment
* : bss segment
* : heap
* : stack
- * _ROMBASE
+ * CONFIG_ROMBASE
* : coreboot text
* : readonly text
*/
INPUT(coreboot_ram.rom)
SECTIONS
{
- . = _ROMBASE;
+ . = CONFIG_ROMBASE;
.ram . : {
_ram = . ;
/* cut _start into last 64k*/
_x = .;
- . = (_x < (_ROMBASE - 0x10000 + ROM_IMAGE_SIZE)) ? (_ROMBASE - 0x10000 + ROM_IMAGE_SIZE) : _x;
+ . = (_x < (CONFIG_ROMBASE - 0x10000 + CONFIG_ROM_IMAGE_SIZE)) ? (CONFIG_ROMBASE - 0x10000 + CONFIG_ROM_IMAGE_SIZE) : _x;
/* This section might be better named .setup */
.rom . : {
_lrom = LOADADDR(.rom);
_elrom = LOADADDR(.rom) + SIZEOF(.rom);
- _iseg = _RAMBASE;
+ _iseg = CONFIG_RAMBASE;
_eiseg = _iseg + SIZEOF(.ram);
_liseg = _ram;
_eliseg = _eram;
/*
* Memory map:
*
- * _RAMBASE
+ * CONFIG_RAMBASE
* : data segment
* : bss segment
* : heap
* : stack
- * _ROMBASE
+ * CONFIG_ROMBASE
* : coreboot text
* : readonly text
*/
TARGET(binary)
SECTIONS
{
- . = _ROMBASE;
+ . = CONFIG_ROMBASE;
/* cut _start into last 64k*/
_x = .;
- . = (_x < (_ROMBASE - 0x10000 + ROM_IMAGE_SIZE)) ? (_ROMBASE - 0x10000 + ROM_IMAGE_SIZE) : _x;
+ . = (_x < (CONFIG_ROMBASE - 0x10000 + CONFIG_ROM_IMAGE_SIZE)) ? (CONFIG_ROMBASE - 0x10000 + CONFIG_ROM_IMAGE_SIZE) : _x;
/* This section might be better named .setup */
.rom . : {
uses CONFIG_USE_INIT
uses CONFIG_USE_PRINTK_IN_CAR
-uses USE_FAILOVER_IMAGE
+uses CONFIG_USE_FAILOVER_IMAGE
uses CONFIG_CBFS
object c_start.S
initobject printk_init.o
-if USE_FAILOVER_IMAGE
+if CONFIG_USE_FAILOVER_IMAGE
else
if CONFIG_CBFS
initobject cbfs_and_run.o
#define printk_debug(fmt, arg...) do_printk(BIOS_DEBUG ,fmt, ##arg)
#define printk_spew(fmt, arg...) do_printk(BIOS_SPEW ,fmt, ##arg)
-#if MAXIMUM_CONSOLE_LOGLEVEL <= BIOS_EMERG
+#if CONFIG_MAXIMUM_CONSOLE_LOGLEVEL <= BIOS_EMERG
#undef printk_emerg
#define printk_emerg(fmt, arg...) do_printk(BIOS_EMERG , "", ##arg)
#endif
-#if MAXIMUM_CONSOLE_LOGLEVEL <= BIOS_ALERT
+#if CONFIG_MAXIMUM_CONSOLE_LOGLEVEL <= BIOS_ALERT
#undef printk_alert
#define printk_alert(fmt, arg...) do_printk(BIOS_EMERG , "", ##arg)
#endif
-#if MAXIMUM_CONSOLE_LOGLEVEL <= BIOS_CRIT
+#if CONFIG_MAXIMUM_CONSOLE_LOGLEVEL <= BIOS_CRIT
#undef printk_crit
#define printk_crit(fmt, arg...) do_printk(BIOS_EMERG , "", ##arg)
#endif
-#if MAXIMUM_CONSOLE_LOGLEVEL <= BIOS_ERR
+#if CONFIG_MAXIMUM_CONSOLE_LOGLEVEL <= BIOS_ERR
#undef printk_err
#define printk_err(fmt, arg...) do_printk(BIOS_EMERG , "", ##arg)
#endif
-#if MAXIMUM_CONSOLE_LOGLEVEL <= BIOS_WARNING
+#if CONFIG_MAXIMUM_CONSOLE_LOGLEVEL <= BIOS_WARNING
#undef printk_warning
#define printk_warning(fmt, arg...) do_printk(BIOS_EMERG , "", ##arg)
#endif
-#if MAXIMUM_CONSOLE_LOGLEVEL <= BIOS_NOTICE
+#if CONFIG_MAXIMUM_CONSOLE_LOGLEVEL <= BIOS_NOTICE
#undef printk_notice
#define printk_notice(fmt, arg...) do_printk(BIOS_EMERG , "", ##arg)
#endif
-#if MAXIMUM_CONSOLE_LOGLEVEL <= BIOS_INFO
+#if CONFIG_MAXIMUM_CONSOLE_LOGLEVEL <= BIOS_INFO
#undef printk_info
#define printk_info(fmt, arg...) do_printk(BIOS_EMERG , "", ##arg)
#endif
-#if MAXIMUM_CONSOLE_LOGLEVEL <= BIOS_DEBUG
+#if CONFIG_MAXIMUM_CONSOLE_LOGLEVEL <= BIOS_DEBUG
#undef printk_debug
#define printk_debug(fmt, arg...) do_printk(BIOS_EMERG , "", ##arg)
#endif
-#if MAXIMUM_CONSOLE_LOGLEVEL <= BIOS_SPEW
+#if CONFIG_MAXIMUM_CONSOLE_LOGLEVEL <= BIOS_SPEW
#undef printk_spew
#define printk_spew(fmt, arg...) do_printk(BIOS_EMERG , "", ##arg)
#endif
__fallback_image = (CONFIG_ROM_PAYLOAD_START & 0xfffffff0) - 8;
- __normal_image = ((CONFIG_ROM_PAYLOAD_START - FALLBACK_SIZE) & 0xfffffff0) - 8;
+ __normal_image = ((CONFIG_ROM_PAYLOAD_START - CONFIG_FALLBACK_SIZE) & 0xfffffff0) - 8;
.globl __id_start
__id_start:
vendor:
- .asciz MAINBOARD_VENDOR
+ .asciz CONFIG_MAINBOARD_VENDOR
part:
- .asciz MAINBOARD_PART_NUMBER
+ .asciz CONFIG_MAINBOARD_PART_NUMBER
.long __id_end + 0x10 - vendor /* Reverse offset to the vendor id */
.long __id_end + 0x10 - part /* Reverse offset to the part number */
-.long PAYLOAD_SIZE + ROM_IMAGE_SIZE /* Size of this romimage */
+.long CONFIG_PAYLOAD_SIZE + CONFIG_ROM_IMAGE_SIZE /* Size of this romimage */
.globl __id_end
__id_end:
SECTIONS {
- . = (_ROMBASE + ROM_IMAGE_SIZE - 0x10) - (__id_end - __id_start);
+ . = (CONFIG_ROMBASE + CONFIG_ROM_IMAGE_SIZE - 0x10) - (__id_end - __id_start);
.id (.): {
*(.id)
}
* Functions for accessing PCI configuration space with type 1 accesses
*/
-#if PCI_IO_CFG_EXT == 0
+#if CONFIG_PCI_IO_CFG_EXT == 0
#define CONFIG_CMD(bus,devfn, where) (0x80000000 | (bus << 16) | (devfn << 8) | (where & ~3))
#else
#define CONFIG_CMD(bus,devfn, where) (0x80000000 | (bus << 16) | (devfn << 8) | ((where & 0xff) & ~3) | ((where & 0xf00)<<16) )
-#if MMCONF_SUPPORT
+#if CONFIG_MMCONF_SUPPORT
#include <console/console.h>
#include <arch/io.h>
*/
#define PCI_MMIO_ADDR(SEGBUS, DEVFN, WHERE) ( \
- MMCONF_BASE_ADDRESS | \
+ CONFIG_MMCONF_BASE_ADDRESS | \
(((SEGBUS) & 0xFFF) << 20) | \
(((DEVFN) & 0xFF) << 12) | \
((WHERE) & 0xFFF))
/* Keep together for sysctl support */
/* Using an global varible can cause problem when we reset the stack from cache as ram to ram*/
#if 0
-int console_loglevel = DEFAULT_CONSOLE_LOGLEVEL;
+int console_loglevel = CONFIG_DEFAULT_CONSOLE_LOGLEVEL;
#else
#define console_loglevel ASM_CONSOLE_LOGLEVEL
#endif
void console_tx_byte(unsigned char byte)
{
if (byte == '\n')
- uart8250_tx_byte(TTYS0_BASE, '\r');
- uart8250_tx_byte(TTYS0_BASE, byte);
+ uart8250_tx_byte(CONFIG_TTYS0_BASE, '\r');
+ uart8250_tx_byte(CONFIG_TTYS0_BASE, byte);
}
int do_printk(int msg_level, const char *fmt, ...)
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
-if HAVE_MP_TABLE
+if CONFIG_HAVE_MP_TABLE
object mpspec.o
end
#object ioapic.o CONFIG_IOAPIC
head = lb_table_init(low_table_end);
low_table_end = (unsigned long)head;
- if (HAVE_OPTION_TABLE == 1) {
+ if (CONFIG_HAVE_OPTION_TABLE == 1) {
struct lb_record *rec_dest, *rec_src;
/* Write the option config table... */
rec_dest = lb_new_record(head);
struct cpu_device_id *id_table;
};
-#ifndef STACK_SIZE
-#error STACK_SIZE not defined
+#ifndef CONFIG_STACK_SIZE
+#error CONFIG_STACK_SIZE not defined
#endif
/* The basic logic comes from the Linux kernel.
- * The invariant is that (1 << 31 - STACK_BITS) == STACK_SIZE
+ * The invariant is that (1 << 31 - STACK_BITS) == CONFIG_STACK_SIZE
* I wish there was simpler way to support multiple stack sizes.
* Oh well.
*/
-#if STACK_SIZE == 4096
+#if CONFIG_STACK_SIZE == 4096
#define STACK_BITS "19"
-#elif STACK_SIZE == 8192
+#elif CONFIG_STACK_SIZE == 8192
#define STACK_BITS "18"
-#elif STACK_SIZE == 16384
+#elif CONFIG_STACK_SIZE == 16384
#define STACK_BITS "17"
-#elif STACK_SIZE == 32768
+#elif CONFIG_STACK_SIZE == 32768
#define STACK_BITS "16"
-#elif STACK_SIZE == 65536
+#elif CONFIG_STACK_SIZE == 65536
#define STACK_BITS "15"
#else
#error Unimplemented stack size
#define SLOW_DOWN_IO
-#ifndef _IO_BASE
-#define _IO_BASE 0
+#ifndef CONFIG_IO_BASE
+#define CONFIG_IO_BASE 0
#endif
#define readb(addr) in_8((volatile uint8_t *)(addr))
* are arrays of bytes, and byte-swapping is not appropriate in
* that case. - paulus
*/
-#define insw(port, buf, ns) _insw_ns((uint16_t *)((port)+_IO_BASE), (buf), (ns))
-#define outsw(port, buf, ns) _outsw_ns((uint16_t *)((port)+_IO_BASE), (buf), (ns))
+#define insw(port, buf, ns) _insw_ns((uint16_t *)((port)+CONFIG_IO_BASE), (buf), (ns))
+#define outsw(port, buf, ns) _outsw_ns((uint16_t *)((port)+CONFIG_IO_BASE), (buf), (ns))
-#define inb(port) in_8((uint8_t *)((port)+_IO_BASE))
-#define outb(val, port) out_8((uint8_t *)((port)+_IO_BASE), (val))
-#define inw(port) in_le16((uint16_t *)((port)+_IO_BASE))
-#define outw(val, port) out_le16((uint16_t *)((port)+_IO_BASE), (val))
-#define inl(port) in_le32((uint32_t *)((port)+_IO_BASE))
-#define outl(val, port) out_le32((uint32_t *)((port)+_IO_BASE), (val))
+#define inb(port) in_8((uint8_t *)((port)+CONFIG_IO_BASE))
+#define outb(val, port) out_8((uint8_t *)((port)+CONFIG_IO_BASE), (val))
+#define inw(port) in_le16((uint16_t *)((port)+CONFIG_IO_BASE))
+#define outw(val, port) out_le16((uint16_t *)((port)+CONFIG_IO_BASE), (val))
+#define inl(port) in_le32((uint32_t *)((port)+CONFIG_IO_BASE))
+#define outl(val, port) out_le32((uint32_t *)((port)+CONFIG_IO_BASE), (val))
#define inb_p(port) inb((port))
#define outb_p(val, port) outb((val), (port))
/*
* The *_ns versions below do byte-swapping.
*/
-#define insw_ns(port, buf, ns) _insw((uint16_t *)((port)+_IO_BASE), (buf), (ns))
-#define outsw_ns(port, buf, ns) _outsw((uint16_t *)((port)+_IO_BASE), (buf), (ns))
+#define insw_ns(port, buf, ns) _insw((uint16_t *)((port)+CONFIG_IO_BASE), (buf), (ns))
+#define outsw_ns(port, buf, ns) _outsw((uint16_t *)((port)+CONFIG_IO_BASE), (buf), (ns))
#define IO_SPACE_LIMIT ~0
u8 rfu;
} __attribute__((packed));
-#if defined(IRQ_SLOT_COUNT)
-#define IRQ_SLOTS_COUNT IRQ_SLOT_COUNT
+#if defined(CONFIG_IRQ_SLOT_COUNT)
+#define IRQ_SLOTS_COUNT CONFIG_IRQ_SLOT_COUNT
#elif (__GNUC__ < 3)
#define IRQ_SLOTS_COUNT 1
#else
extern const struct irq_routing_table intel_irq_routing_table;
-#if defined(DEBUG) && defined(HAVE_PIRQ_TABLE)
+#if defined(CONFIG_DEBUG) && defined(CONFIG_HAVE_PIRQ_TABLE)
void check_pirq_routing_table(void);
#else
#define check_pirq_routing_table() do {} while(0)
#endif
-#if defined(HAVE_PIRQ_TABLE)
+#if defined(CONFIG_HAVE_PIRQ_TABLE)
unsigned long copy_pirq_routing_table(unsigned long start);
#else
#define copy_pirq_routing_table(start) (start)
*/
%%PROCESSOR_INIT%%
-#if USE_DCACHE_RAM == 1
-#define DCACHE_RAM_END (DCACHE_RAM_BASE + DCACHE_RAM_SIZE - 1)
+#if CONFIG_USE_DCACHE_RAM == 1
+#define DCACHE_RAM_END (CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE - 1)
/*
* Initialize data cache blocks
* (assumes cache block size of 32 bytes)
* NOTE: This may need to be moved to FAMILY_INIT if
* dcbz is not supported on all CPU's
*/
- lis r1, DCACHE_RAM_BASE@h
- ori r1, r1, DCACHE_RAM_BASE@l
- li r3, (DCACHE_RAM_SIZE / 32)
+ lis r1, CONFIG_DCACHE_RAM_BASE@h
+ ori r1, r1, CONFIG_DCACHE_RAM_BASE@l
+ li r3, (CONFIG_DCACHE_RAM_SIZE / 32)
mtctr r3
0: dcbz r0, r1
addi r1, r1, 32
* it 16-byte aligned to cover both cases. Also we have to ensure that
* the first word is located within the cache.
*/
- lis r1, (DCACHE_RAM_BASE+DCACHE_RAM_SIZE)@h
- ori r1, r1, (DCACHE_RAM_BASE+DCACHE_RAM_SIZE)@l
+ lis r1, (CONFIG_DCACHE_RAM_BASE+CONFIG_DCACHE_RAM_SIZE)@h
+ ori r1, r1, (CONFIG_DCACHE_RAM_BASE+CONFIG_DCACHE_RAM_SIZE)@l
lis r0, 0
stwu r0, -4(r1)
stwu r0, -4(r1)
/*
* Clear stack
*/
- lis r4, DCACHE_RAM_BASE@h
- ori r4, r4, DCACHE_RAM_BASE@l
+ lis r4, CONFIG_DCACHE_RAM_BASE@h
+ ori r4, r4, CONFIG_DCACHE_RAM_BASE@l
lis r7, DCACHE_RAM_END@h
ori r7, r7, DCACHE_RAM_END@l
lis r5, 0
* Complete rest of initialization in C (ppc_main)
*/
rfi
-#endif /* USE_DCACHE_RAM */
+#endif /* CONFIG_USE_DCACHE_RAM */
/*
* Stop here if something goes wrong
/*
* Memory map:
*
- * _ROMBASE : start of ROM
- * _RESET : reset vector (may be at top of ROM)
+ * CONFIG_ROMBASE : start of ROM
+ * CONFIG_RESET : reset vector (may be at top of ROM)
* _EXCEPTIONS_VECTORS : exception table
*
- * _ROMSTART : coreboot text
+ * CONFIG_ROMSTART : coreboot text
* : payload text
*
- * _RAMBASE : address to copy payload
+ * CONFIG_RAMBASE : address to copy payload
*/
/*
/*
* Absolute location of base of ROM
*/
- . = _ROMBASE;
+ . = CONFIG_ROMBASE;
/*
* Absolute location of reset vector. This may actually be at the
* the top of ROM.
*/
- . = _RESET;
+ . = CONFIG_RESET;
.reset . : {
*(.rom.reset);
. = ALIGN(16);
/*
* Absolute location of exception vector table.
*/
- . = _EXCEPTION_VECTORS;
+ . = CONFIG_EXCEPTION_VECTORS;
.exception_vectors . : {
*(.rom.exception_vectors);
. = ALIGN(16);
/*
* Absolute location of coreboot initialization code in ROM.
*/
- . = _ROMSTART;
+ . = CONFIG_ROMSTART;
.rom . : {
_rom = .;
*(.rom.text);
/*
* Absolute location of where coreboot will be relocated in RAM.
*/
- _iseg = _RAMBASE;
+ _iseg = CONFIG_RAMBASE;
_eiseg = _iseg + SIZEOF(.ram);
_liseg = _ram;
_eliseg = _eram;
{
uint8_t res;
- out_le32((unsigned *)PCIC0_CFGADDR, CONFIG_CMD(bus, devfn, where));
- res = in_8((unsigned char *)PCIC0_CFGDATA + (where & 3));
+ out_le32((unsigned *)CONFIG_PCIC0_CFGADDR, CONFIG_CMD(bus, devfn, where));
+ res = in_8((unsigned char *)CONFIG_PCIC0_CFGDATA + (where & 3));
return res;
}
{
uint16_t res;
- out_le32((unsigned *)PCIC0_CFGADDR, CONFIG_CMD(bus, devfn, where));
- res = in_le16((unsigned short *)PCIC0_CFGDATA + (where & 2));
+ out_le32((unsigned *)CONFIG_PCIC0_CFGADDR, CONFIG_CMD(bus, devfn, where));
+ res = in_le16((unsigned short *)CONFIG_PCIC0_CFGDATA + (where & 2));
return res;
}
{
uint32_t res;
- out_le32((unsigned *)PCIC0_CFGADDR, CONFIG_CMD(bus, devfn, where));
- res = in_le32((unsigned *)PCIC0_CFGDATA);
+ out_le32((unsigned *)CONFIG_PCIC0_CFGADDR, CONFIG_CMD(bus, devfn, where));
+ res = in_le32((unsigned *)CONFIG_PCIC0_CFGDATA);
return res;
}
int pci_ppc_write_config8(unsigned char bus, int devfn, int where, uint8_t data)
{
- out_le32((unsigned *)PCIC0_CFGADDR, CONFIG_CMD(bus, devfn, where));
- out_8((unsigned char *)PCIC0_CFGDATA + (where & 3), data);
+ out_le32((unsigned *)CONFIG_PCIC0_CFGADDR, CONFIG_CMD(bus, devfn, where));
+ out_8((unsigned char *)CONFIG_PCIC0_CFGDATA + (where & 3), data);
return 0;
}
int pci_ppc_write_config16(unsigned char bus, int devfn, int where, uint16_t data)
{
- out_le32((unsigned *)PCIC0_CFGADDR, CONFIG_CMD(bus, devfn, where));
- out_le16((unsigned short *)PCIC0_CFGDATA + (where & 2), data);
+ out_le32((unsigned *)CONFIG_PCIC0_CFGADDR, CONFIG_CMD(bus, devfn, where));
+ out_le16((unsigned short *)CONFIG_PCIC0_CFGDATA + (where & 2), data);
return 0;
}
int pci_ppc_write_config32(unsigned char bus, int devfn, int where, uint32_t data)
{
- out_le32((unsigned *)PCIC0_CFGADDR, CONFIG_CMD(bus, devfn, where));
- out_le32((unsigned *)PCIC0_CFGDATA, data);
+ out_le32((unsigned *)CONFIG_PCIC0_CFGADDR, CONFIG_CMD(bus, devfn, where));
+ out_le32((unsigned *)CONFIG_PCIC0_CFGDATA, data);
return 0;
}
/* Keep together for sysctl support */
-int console_loglevel = DEFAULT_CONSOLE_LOGLEVEL;
+int console_loglevel = CONFIG_DEFAULT_CONSOLE_LOGLEVEL;
extern int vtxprintf(void (*)(unsigned char), const char *, va_list);
extern void uart8250_tx_byte(unsigned, unsigned char);
void console_tx_byte(unsigned char byte)
{
if (byte == '\n')
- uart8250_tx_byte(TTYS0_BASE, '\r');
- uart8250_tx_byte(TTYS0_BASE, byte);
+ uart8250_tx_byte(CONFIG_TTYS0_BASE, '\r');
+ uart8250_tx_byte(CONFIG_TTYS0_BASE, byte);
}
int do_printk(int msg_level, const char *fmt, ...)
#define ENTER '\r'
#define ESCAPE '\x1b'
-#ifndef AUTOBOOT_CMDLINE
+#ifndef CONFIG_AUTOBOOT_CMDLINE
#define autoboot(mem)
#endif
-#if !AUTOBOOT_DELAY
+#if !CONFIG_AUTOBOOT_DELAY
#define autoboot_delay() 0 /* success */
#endif
free(boot_file);
}
-#ifdef AUTOBOOT_CMDLINE
-#if AUTOBOOT_DELAY
+#ifdef CONFIG_AUTOBOOT_CMDLINE
+#if CONFIG_AUTOBOOT_DELAY
static inline int autoboot_delay(void)
{
unsigned int timeout;
key = 0;
printk_info("Press <Enter> for default boot, or <Esc> for boot prompt... ");
- for (sec = AUTOBOOT_DELAY; sec>0 && key==0; sec--) {
+ for (sec = CONFIG_AUTOBOOT_DELAY; sec>0 && key==0; sec--) {
printk_info("%d", sec);
timeout = 10;
while (timeout-- > 0) {
return 0; /* default accepted */
}
}
-#endif /* AUTOBOOT_DELAY */
+#endif /* CONFIG_AUTOBOOT_DELAY */
static void autoboot(struct lb_memory *mem)
{
return;
if (autoboot_delay()==0) {
- printk_info("boot: %s\n", AUTOBOOT_CMDLINE);
- boot(mem, AUTOBOOT_CMDLINE);
+ printk_info("boot: %s\n", CONFIG_AUTOBOOT_CMDLINE);
+ boot(mem, CONFIG_AUTOBOOT_CMDLINE);
}
}
-#endif /* AUTOBOOT_CMDLINE */
+#endif /* CONFIG_AUTOBOOT_CMDLINE */
/* The main routine */
int filo(struct lb_memory *mem)
/* The above didn't work, ask user */
while (havechar())
getchar();
-#ifdef AUTOBOOT_CMDLINE
- strncpy(line, AUTOBOOT_CMDLINE, sizeof(line)-1);
+#ifdef CONFIG_AUTOBOOT_CMDLINE
+ strncpy(line, CONFIG_AUTOBOOT_CMDLINE, sizeof(line)-1);
line[sizeof(line)-1] = '\0';
#else
line[0] = '\0';
#include <boot/tables.h>
#include <boot/elf.h>
#include <cbfs.h>
-#if HAVE_ACPI_RESUME
+#if CONFIG_HAVE_ACPI_RESUME
#include <arch/acpi.h>
#endif
dev_initialize();
post_code(0x89);
-#if HAVE_ACPI_RESUME == 1
+#if CONFIG_HAVE_ACPI_RESUME == 1
suspend_resume();
post_code(0x8a);
#endif
*/
lb_mem = write_tables();
#if CONFIG_CBFS == 1
-# if USE_FALLBACK_IMAGE == 1
+# if CONFIG_USE_FALLBACK_IMAGE == 1
cbfs_load_payload(lb_mem, "fallback/payload");
# else
cbfs_load_payload(lb_mem, "normal/payload");
## This is Architecture independant part of the makefile
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_AP_CODE_IN_CAR
-uses ASSEMBLER_DEBUG
+uses CONFIG_ASSEMBLER_DEBUG
makedefine CPP:= $(CC) -x assembler-with-cpp -DASSEMBLY -E
makedefine LIBGCC_FILE_NAME := $(shell $(CC) -print-libgcc-file-name)
makedefine GCC ?= $(CC)
makedefine GCC_INC_DIR := $(shell LC_ALL=C $(GCC) -print-search-dirs | sed -ne "s/install: \(.*\)/\1include/gp")
-makedefine CPPFLAGS := -I$(TOP)/src/include -I$(TOP)/src/arch/$(ARCH)/include -I$(GCC_INC_DIR) $(CPUFLAGS)
-makedefine CFLAGS := $(CPU_OPT) $(DISTRO_CFLAGS) $(CPPFLAGS) -Os -nostdinc -nostdlib -Wall -Wundef -Wstrict-prototypes -Wno-trigraphs -Werror-implicit-function-declaration -Wstrict-aliasing -Wshadow -fno-common -ffreestanding -fno-builtin -fomit-frame-pointer
+makedefine CPPFLAGS := -I$(TOP)/src/include -I$(TOP)/src/arch/$(CONFIG_ARCH)/include -I$(GCC_INC_DIR) $(CPUFLAGS)
+makedefine CFLAGS := $(CONFIG_CPU_OPT) $(DISTRO_CFLAGS) $(CPPFLAGS) -Os -nostdinc -nostdlib -Wall -Wundef -Wstrict-prototypes -Wno-trigraphs -Werror-implicit-function-declaration -Wstrict-aliasing -Wshadow -fno-common -ffreestanding -fno-builtin -fomit-frame-pointer
-if ASSEMBLER_DEBUG
+if CONFIG_ASSEMBLER_DEBUG
makedefine DEBUG_CFLAGS := -g -dA -fverbose-asm
end
makerule coreboot.strip
depends "coreboot"
- action "$(OBJCOPY) -O binary coreboot coreboot.strip"
+ action "$(CONFIG_OBJCOPY) -O binary coreboot coreboot.strip"
end
makerule coreboot.a
depends "$(OBJECTS)"
action "rm -f coreboot.a"
- action "$(CROSS_COMPILE)ar cr coreboot.a $(OBJECTS)"
+ action "$(CONFIG_CROSS_COMPILE)ar cr coreboot.a $(OBJECTS)"
end
makerule coreboot_ram.o
- depends "src/arch/$(ARCH)/lib/c_start.o $(DRIVER) coreboot.a $(LIBGCC_FILE_NAME)"
- action "$(CC) $(DISTRO_LFLAGS) -nostdlib -r -o $@ src/arch/$(ARCH)/lib/c_start.o $(DRIVER) -Wl,-\( coreboot.a $(LIBGCC_FILE_NAME) -Wl,-\)"
+ depends "src/arch/$(CONFIG_ARCH)/lib/c_start.o $(DRIVER) coreboot.a $(LIBGCC_FILE_NAME)"
+ action "$(CC) $(DISTRO_LFLAGS) -nostdlib -r -o $@ src/arch/$(CONFIG_ARCH)/lib/c_start.o $(DRIVER) -Wl,-\( coreboot.a $(LIBGCC_FILE_NAME) -Wl,-\)"
end
makerule coreboot_ram
depends "coreboot_ram.o $(TOP)/src/config/coreboot_ram.ld ldoptions"
action "$(CC) $(DISTRO_LFLAGS) -nostdlib -nostartfiles -static -o $@ -T $(TOP)/src/config/coreboot_ram.ld coreboot_ram.o"
- action "$(CROSS_COMPILE)nm -n coreboot_ram | sort > coreboot_ram.map"
+ action "$(CONFIG_CROSS_COMPILE)nm -n coreboot_ram | sort > coreboot_ram.map"
end
##
makerule coreboot_ram.bin
depends "coreboot_ram"
- action "$(OBJCOPY) -O binary $< $@"
+ action "$(CONFIG_OBJCOPY) -O binary $< $@"
end
makerule coreboot_ram.nrv2b
makerule coreboot_apc.a
depends "apc_auto.o"
action "rm -f coreboot_apc.a"
- action "$(CROSS_COMPILE)ar cr coreboot_apc.a apc_auto.o"
+ action "$(CONFIG_CROSS_COMPILE)ar cr coreboot_apc.a apc_auto.o"
end
makerule coreboot_apc.o
- depends "src/arch/$(ARCH)/lib/c_start.o coreboot_apc.a $(LIBGCC_FILE_NAME)"
+ depends "src/arch/$(CONFIG_ARCH)/lib/c_start.o coreboot_apc.a $(LIBGCC_FILE_NAME)"
action "$(CC) $(DISTRO_LFLAGS) -nostdlib -r -o $@ $^"
end
makerule coreboot_apc
depends "coreboot_apc.o $(TOP)/src/config/coreboot_apc.ld ldoptions"
action "$(CC) $(DISTRO_LFLAGS) -nostdlib -nostartfiles -static -o $@ -T $(TOP)/src/config/coreboot_apc.ld coreboot_apc.o"
- action "$(CROSS_COMPILE)nm -n coreboot_apc | sort > coreboot_apc.map"
+ action "$(CONFIG_CROSS_COMPILE)nm -n coreboot_apc | sort > coreboot_apc.map"
end
##
makerule coreboot_apc.bin
depends "coreboot_apc"
- action "$(OBJCOPY) -O binary $< $@"
+ action "$(CONFIG_OBJCOPY) -O binary $< $@"
end
makerule coreboot_apc.nrv2b
makerule coreboot
depends "crt0.o $(INIT-OBJECTS) $(COREBOOT_APC) $(COREBOOT_RAM_ROM) ldscript.ld"
action "$(CC) $(DISTRO_LFLAGS) -nostdlib -nostartfiles -static -o $@ -T ldscript.ld crt0.o $(INIT-OBJECTS)"
- action "$(CROSS_COMPILE)nm -n coreboot | sort > coreboot.map"
- action "$(CROSS_COMPILE)objdump -dS coreboot > coreboot.disasm"
+ action "$(CONFIG_CROSS_COMPILE)nm -n coreboot | sort > coreboot.map"
+ action "$(CONFIG_CROSS_COMPILE)objdump -dS coreboot > coreboot.disasm"
end
# the buildrom tool
makerule buildrom
depends "$(TOP)/util/buildrom/buildrom.c"
- action "$(HOSTCC) -o $@ $<"
+ action "$(CONFIG_HOSTCC) -o $@ $<"
end
# Force crt0.s (which has build time version code in it to rebuild every time)
# generate an assembly listing via -a switch.
makerule crt0.o
depends "crt0.s"
- action "$(CC) -Wa,-acdlns -c $(CPU_OPT) -o $@ $< >crt0.disasm"
+ action "$(CC) -Wa,-acdlns -c $(CONFIG_CPU_OPT) -o $@ $< >crt0.disasm"
end
makerule etags
# be in a correct and valid state if it exists because the move is atomic.
makerule ../romcc
depends "$(TOP)/util/romcc/romcc.c"
- action "$(HOSTCC) -g $(HOSTCFLAGS) $< -o romcc.tmpfile"
+ action "$(CONFIG_HOSTCC) -g $(HOSTCFLAGS) $< -o romcc.tmpfile"
action "mv romcc.tmpfile $@"
end
makerule build_opt_tbl
depends "$(TOP)/util/options/build_opt_tbl.c $(TOP)/src/include/pc80/mc146818rtc.h $(TOP)/src/include/boot/coreboot_tables.h Makefile.settings Makefile"
- action "$(HOSTCC) $(HOSTCFLAGS) $(CPUFLAGS) $< -o $@"
+ action "$(CONFIG_HOSTCC) $(HOSTCFLAGS) $(CPUFLAGS) $< -o $@"
end
makerule option_table.h option_table.c
- depends "build_opt_tbl $(MAINBOARD)/cmos.layout"
- action "./build_opt_tbl --config $(MAINBOARD)/cmos.layout --header option_table.h --option option_table.c"
+ depends "build_opt_tbl $(CONFIG_MAINBOARD)/cmos.layout"
+ action "./build_opt_tbl --config $(CONFIG_MAINBOARD)/cmos.layout --header option_table.h --option option_table.c"
end
-if HAVE_OPTION_TABLE
+if CONFIG_HAVE_OPTION_TABLE
object ./option_table.o
end
export always
comment "X86 is the default"
end
-define ARCH
+define CONFIG_ARCH
default "i386"
export always
comment "Default architecture is i386, options are alpha and ppc"
end
-define HAVE_MOVNTI
+define CONFIG_HAVE_MOVNTI
default 0
export always
comment "This cpu supports the MOVNTI directive"
# Build options
###############################################
-define CROSS_COMPILE
+define CONFIG_CROSS_COMPILE
default ""
export always
comment "Cross compiler prefix"
end
define CC
- default "$(CROSS_COMPILE)gcc"
+ default "$(CONFIG_CROSS_COMPILE)gcc"
export always
comment "Target C Compiler"
end
-define HOSTCC
+define CONFIG_HOSTCC
default "gcc"
export always
comment "Host C Compiler"
end
-define CPU_OPT
+define CONFIG_CPU_OPT
default none
export used
comment "Additional per-cpu CFLAGS"
end
-define OBJCOPY
- default "$(CROSS_COMPILE)objcopy --gap-fill 0xff"
+define CONFIG_OBJCOPY
+ default "$(CONFIG_CROSS_COMPILE)objcopy --gap-fill 0xff"
export always
comment "Objcopy command"
end
# ROM image options
###############################################
-define HAVE_FALLBACK_BOOT
+define CONFIG_HAVE_FALLBACK_BOOT
format "%d"
default 0
export always
comment "Set if fallback booting required"
end
-define HAVE_FAILOVER_BOOT
+define CONFIG_HAVE_FAILOVER_BOOT
format "%d"
default 0
export always
comment "Set if failover booting required"
end
-define USE_FALLBACK_IMAGE
+define CONFIG_USE_FALLBACK_IMAGE
format "%d"
default 0
export used
comment "Set to build a fallback image"
end
-define USE_FAILOVER_IMAGE
+define CONFIG_USE_FAILOVER_IMAGE
format "%d"
default 0
export used
comment "Set to build a failover image"
end
-define FALLBACK_SIZE
+define CONFIG_FALLBACK_SIZE
default 65536
format "0x%x"
export used
comment "Default fallback image size"
end
-define FAILOVER_SIZE
+define CONFIG_FAILOVER_SIZE
default 0
format "0x%x"
export used
comment "Default failover image size"
end
-define ROM_SIZE
+define CONFIG_ROM_SIZE
default none
format "0x%x"
export used
comment "Size of your ROM"
end
-define ROM_IMAGE_SIZE
+define CONFIG_ROM_IMAGE_SIZE
default 65535
format "0x%x"
export always
comment "Default image size"
end
-define ROM_SECTION_SIZE
- default {FALLBACK_SIZE}
+define CONFIG_ROM_SECTION_SIZE
+ default {CONFIG_FALLBACK_SIZE}
format "0x%x"
export used
comment "Default rom section size"
end
-define ROM_SECTION_OFFSET
- default {ROM_SIZE - FALLBACK_SIZE}
+define CONFIG_ROM_SECTION_OFFSET
+ default {CONFIG_ROM_SIZE - CONFIG_FALLBACK_SIZE}
format "0x%x"
export used
comment "Default rom section offset"
end
-define PAYLOAD_SIZE
- default {ROM_SECTION_SIZE - ROM_IMAGE_SIZE}
+define CONFIG_PAYLOAD_SIZE
+ default {CONFIG_ROM_SECTION_SIZE - CONFIG_ROM_IMAGE_SIZE}
format "0x%x"
export always
comment "Default payload size"
end
-define _ROMBASE
- default {PAYLOAD_SIZE}
+define CONFIG_ROMBASE
+ default {CONFIG_PAYLOAD_SIZE}
format "0x%x"
export always
comment "Base address of coreboot in ROM"
end
-define _ROMSTART
+define CONFIG_ROMSTART
default none
format "0x%x"
export used
comment "Start address of coreboot in ROM"
end
-define _RESET
- default {_ROMBASE}
+define CONFIG_RESET
+ default {CONFIG_ROMBASE}
format "0x%x"
export always
comment "Hardware reset vector address"
end
-define _EXCEPTION_VECTORS
- default {_ROMBASE+0x100}
+define CONFIG_EXCEPTION_VECTORS
+ default {CONFIG_ROMBASE+0x100}
format "0x%x"
export always
comment "Address of exception vector table"
end
-define STACK_SIZE
+define CONFIG_STACK_SIZE
default 0x2000
format "0x%x"
export always
comment "Default stack size"
end
-define HEAP_SIZE
+define CONFIG_HEAP_SIZE
default 0x2000
format "0x%x"
export always
comment "Default heap size"
end
-define _RAMBASE
+define CONFIG_RAMBASE
default none
format "0x%x"
export always
comment "Base address of coreboot in RAM"
end
-define _RAMSTART
+define CONFIG_RAMSTART
default none
format "0x%x"
export used
comment "Start address of coreboot in RAM"
end
-define USE_DCACHE_RAM
+define CONFIG_USE_DCACHE_RAM
default 0
export always
comment "Use data cache as temporary RAM if possible"
end
-define CAR_FAM10
+define CONFIG_CAR_FAM10
default 0
export always
comment "AMD family 10 CAR requires additional setup"
end
-define DCACHE_RAM_BASE
+define CONFIG_DCACHE_RAM_BASE
default 0xc0000
format "0x%x"
export always
comment "Base address of data cache when using it for temporary RAM"
end
-define DCACHE_RAM_SIZE
+define CONFIG_DCACHE_RAM_SIZE
default 0x1000
format "0x%x"
export always
comment "Size of data cache when using it for temporary RAM"
end
-define DCACHE_RAM_GLOBAL_VAR_SIZE
+define CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE
default 0
format "0x%x"
export always
export always
comment "will copy coreboot_apc to AP cache ane execute in AP"
end
-define MEM_TRAIN_SEQ
+define CONFIG_MEM_TRAIN_SEQ
default 0
export always
comment "0: three for in bsp, 1: on every core0, 2: one for on bsp"
end
-define WAIT_BEFORE_CPUS_INIT
+define CONFIG_WAIT_BEFORE_CPUS_INIT
default 0
export always
comment "execute cpus_ready_for_init if it is set to 1"
end
-define XIP_ROM_BASE
+define CONFIG_XIP_ROM_BASE
default 0
format "0x%x"
export used
comment "Start address of area to cache during coreboot execution directly from ROM"
end
-define XIP_ROM_SIZE
+define CONFIG_XIP_ROM_SIZE
default 0
format "0x%x"
export used
export always
comment "Kilobytes of memory to initialized before executing code from RAM"
end
-define HAVE_OPTION_TABLE
+define CONFIG_HAVE_OPTION_TABLE
default 0
export always
comment "Export CMOS option table"
end
-define USE_OPTION_TABLE
+define CONFIG_USE_OPTION_TABLE
format "%d"
- default {HAVE_OPTION_TABLE && !USE_FALLBACK_IMAGE}
+ default {CONFIG_HAVE_OPTION_TABLE && !CONFIG_USE_FALLBACK_IMAGE}
export always
comment "Use option table"
end
###############################################
# CMOS variable options
###############################################
-define LB_CKS_RANGE_START
+define CONFIG_LB_CKS_RANGE_START
default 49
format "%d"
export always
comment "First CMOS byte to use for coreboot options"
end
-define LB_CKS_RANGE_END
+define CONFIG_LB_CKS_RANGE_END
default 125
format "%d"
export always
comment "Last CMOS byte to use for coreboot options"
end
-define LB_CKS_LOC
+define CONFIG_LB_CKS_LOC
default 126
format "%d"
export always
# Build targets
###############################################
-define CRT0
- default "$(TOP)/src/arch/$(ARCH)/init/crt0.S.lb"
+define CONFIG_CRT0
+ default "$(TOP)/src/arch/$(CONFIG_ARCH)/init/crt0.S.lb"
export always
comment "Main initialization target"
end
# Debugging/Logging options
###############################################
-define DEBUG
+define CONFIG_DEBUG
default 0
export always
comment "Enable x86emu debugging code"
export always
comment "Log messages to ehci debug port console"
end
-define DEFAULT_CONSOLE_LOGLEVEL
+define CONFIG_DEFAULT_CONSOLE_LOGLEVEL
default 7
export always
comment "Console will log at this level unless changed"
end
-define MAXIMUM_CONSOLE_LOGLEVEL
+define CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
default 8
export always
comment "Error messages up to this level can be printed"
export always
comment "Enable SERIAL POST codes"
end
-define NO_POST
+define CONFIG_NO_POST
default none
export used
comment "Disable POST codes"
end
-define TTYS0_BASE
+define CONFIG_TTYS0_BASE
default 0x3f8
format "0x%x"
export always
comment "Base address for 8250 uart for the serial console"
end
-define TTYS0_BAUD
+define CONFIG_TTYS0_BAUD
default 115200
export always
comment "Default baud rate for serial console"
end
-define TTYS0_DIV
+define CONFIG_TTYS0_DIV
default none
format "%d"
export used
comment "Allow UART divisor to be set explicitly"
end
-define TTYS0_LCS
+define CONFIG_TTYS0_LCS
default 0x3
format "0x%x"
export always
export always
comment "use printk instead of print in CAR stage code"
end
-define ASSEMBLER_DEBUG
+define CONFIG_ASSEMBLER_DEBUG
default 0
export always
comment "Create disassembly files for debugging"
# Mainboard options
###############################################
-define MAINBOARD
+define CONFIG_MAINBOARD
default "Mainboard_not_set"
export always
comment "Mainboard name"
end
-define MAINBOARD_PART_NUMBER
+define CONFIG_MAINBOARD_PART_NUMBER
default "Part_number_not_set"
export always
format "\"%s\""
comment "Part number of mainboard"
end
-define MAINBOARD_VENDOR
+define CONFIG_MAINBOARD_VENDOR
default "Vendor_not_set"
export always
format "\"%s\""
comment "Vendor of mainboard"
end
-define MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+define CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
default 0
export always
comment "PCI Vendor ID of mainboard manufacturer"
end
-define MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+define CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
default 0
format "0x%x"
export always
comment "PCI susbsystem device id assigned my mainboard manufacturer"
end
-define MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+define CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
default none
export used
comment "Default power on after power fail setting"
export always
comment "Should application processors go to SIPI wait state after initialization? (Required for Intel Core Duo)"
end
-define HAVE_MP_TABLE
+define CONFIG_HAVE_MP_TABLE
default none
export used
comment "Define to build an MP table"
end
-define SERIAL_CPU_INIT
+define CONFIG_SERIAL_CPU_INIT
default 1
export always
comment "Serialize CPU init"
end
-define APIC_ID_OFFSET
+define CONFIG_APIC_ID_OFFSET
default 0
export always
comment "We need to share this value between cache_as_ram_auto.c and northbridge.c"
end
-define ENABLE_APIC_EXT_ID
+define CONFIG_ENABLE_APIC_EXT_ID
default 0
export always
comment "Enable APIC ext id mode 8 bit"
end
-define LIFT_BSP_APIC_ID
+define CONFIG_LIFT_BSP_APIC_ID
default 0
export always
comment "decide if we lift bsp apic id while ap apic id"
comment "Boot image is located in ROM"
end
define CONFIG_ROM_PAYLOAD_START
- default {0xffffffff - ROM_SIZE + ROM_SECTION_OFFSET + 1}
+ default {0xffffffff - CONFIG_ROM_SIZE + CONFIG_ROM_SECTION_OFFSET + 1}
format "0x%x"
export always
comment "ROM stream start location"
export always
comment "The new CBFS file system"
end
-define AUTOBOOT_DELAY
+define CONFIG_AUTOBOOT_DELAY
default 2
export always
comment "Delay (in seconds) before autobooting"
end
-define AUTOBOOT_CMDLINE
+define CONFIG_AUTOBOOT_CMDLINE
default "hdc1:/vmlinuz root=/dev/hdc3 console=tty0 console=ttyS0,115200"
export always
format "\"%s\""
comment "Default command line when autobooting"
end
-define USE_WATCHDOG_ON_BOOT
+define CONFIG_USE_WATCHDOG_ON_BOOT
default 0
export always
comment "Use the watchdog on booting"
# IRQ options
###############################################
-define HAVE_PIRQ_TABLE
+define CONFIG_HAVE_PIRQ_TABLE
default none
export used
comment "Define if we have a PIRQ table"
end
-define PIRQ_ROUTE
+define CONFIG_PIRQ_ROUTE
default 0
export always
comment "Define if we have a PIRQ table and want routing IRQs"
end
-define IRQ_SLOT_COUNT
+define CONFIG_IRQ_SLOT_COUNT
default none
export used
comment "Number of IRQ slots"
export always
comment "Define to include IDE support"
end
-define IDE_BOOT_DRIVE
+define CONFIG_IDE_BOOT_DRIVE
default 0
export always
comment "Disk number of boot drive"
end
-define IDE_SWAB
+define CONFIG_IDE_SWAB
default none
export used
comment "Swap bytes when reading from IDE device"
end
-define IDE_OFFSET
+define CONFIG_IDE_OFFSET
default 0
export always
comment "Sector at which to start searching for boot image"
# Options for memory mapped I/O
###############################################
-define PCI_IO_CFG_EXT
+define CONFIG_PCI_IO_CFG_EXT
default 0
export always
comment "allow 4K register space via io CFG port"
end
-define PCIC0_CFGADDR
+define CONFIG_PCIC0_CFGADDR
default none
format "0x%x"
export used
comment "Address of PCI Configuration Address Register"
end
-define PCIC0_CFGDATA
+define CONFIG_PCIC0_CFGDATA
default none
format "0x%x"
export used
comment "Address of PCI Configuration Data Register"
end
-define ISA_IO_BASE
+define CONFIG_ISA_IO_BASE
default none
format "0x%x"
export used
comment "Base address of PCI/ISA I/O address range"
end
-define ISA_MEM_BASE
+define CONFIG_ISA_MEM_BASE
default none
format "0x%x"
export used
comment "Base address of PCI/ISA memory address range"
end
-define PNP_CFGADDR
+define CONFIG_PNP_CFGADDR
default none
format "0x%x"
export used
comment "PNP Configuration Address Register offset"
end
-define PNP_CFGDATA
+define CONFIG_PNP_CFGDATA
default none
format "0x%x"
export used
comment "PNP Configuration Data Register offset"
end
-define _IO_BASE
+define CONFIG_IO_BASE
default none
format "0x%x"
export used
# Options for embedded systems
###############################################
-define EMBEDDED_RAM_SIZE
+define CONFIG_EMBEDDED_RAM_SIZE
default none
export used
comment "Embedded boards generally have fixed RAM size"
comment "Compile in gdb stub support?"
end
-define HAVE_INIT_TIMER
+define CONFIG_HAVE_INIT_TIMER
default 0
export always
comment "Have a init_timer function"
end
-define HAVE_HARD_RESET
+define CONFIG_HAVE_HARD_RESET
default none
export used
comment "Have hard reset"
end
-define HAVE_SMI_HANDLER
+define CONFIG_HAVE_SMI_HANDLER
default 0
export always
comment "Set, if the board needs an SMI handler"
end
-define MEMORY_HOLE
+define CONFIG_MEMORY_HOLE
default none
export used
comment "Set to deal with memory hole"
end
-define MAX_REBOOT_CNT
+define CONFIG_MAX_REBOOT_CNT
default 3
export always
comment "Set maximum reboots"
# Misc device options
###############################################
-define HAVE_FANCTL
+define CONFIG_HAVE_FANCTL
default 0
export used
comment "Include board specific FAN control initialization"
export used
comment "Use timer2 to callibrate the x86 time stamp counter"
end
-define INTEL_PPRO_MTRR
+define CONFIG_INTEL_PPRO_MTRR
default none
export used
comment ""
export used
comment "Implement udelay with x86 io registers"
end
-define FAKE_SPDROM
+define CONFIG_FAKE_SPDROM
default 0
export always
comment "Use this to fake spd rom values"
end
-define HAVE_ACPI_TABLES
+define CONFIG_HAVE_ACPI_TABLES
default 0
export always
comment "Define to build ACPI tables"
end
-define HAVE_ACPI_RESUME
+define CONFIG_HAVE_ACPI_RESUME
default 0
export always
comment "Define to build ACPI with resume support"
end
-define ACPI_SSDTX_NUM
+define CONFIG_ACPI_SSDTX_NUM
default 0
export always
comment "extra ssdt num for PCI Device"
end
-define AGP_APERTURE_SIZE
+define CONFIG_AGP_APERTURE_SIZE
default none
export used
format "0x%x"
comment "AGP graphics virtual memory aperture size"
end
-define HT_CHAIN_UNITID_BASE
+define CONFIG_HT_CHAIN_UNITID_BASE
default 1
export always
comment "this will be first hypertransport device's unitid base, if sb ht chain only has one ht device, it could be 0"
end
-define HT_CHAIN_END_UNITID_BASE
+define CONFIG_HT_CHAIN_END_UNITID_BASE
default 0x20
export always
- comment "this will be unit id of the end of hypertransport chain (usually the real SB) if it is small than HT_CHAIN_UNITID_BASE, it could be 0"
+ comment "this will be unit id of the end of hypertransport chain (usually the real SB) if it is small than CONFIG_HT_CHAIN_UNITID_BASE, it could be 0"
end
-define SB_HT_CHAIN_UNITID_OFFSET_ONLY
+define CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY
default 1
export always
comment "this will decided if only offset SB hypertransport chain"
end
-define SB_HT_CHAIN_ON_BUS0
+define CONFIG_SB_HT_CHAIN_ON_BUS0
default 0
export always
comment "this will make SB hypertransport chain sit on bus 0, if it is 1, will put sb ht chain on bus 0, if it is 2 will put other chain on 0x40, 0x80, 0xc0"
end
-define PCI_BUS_SEGN_BITS
+define CONFIG_PCI_BUS_SEGN_BITS
default 0
export always
comment "It could be 0, 1, 2, 3 and 4 only"
end
-define MMCONF_SUPPORT
+define CONFIG_MMCONF_SUPPORT
default 0
export always
comment "enable mmconfig for pci conf"
end
-define MMCONF_SUPPORT_DEFAULT
+define CONFIG_MMCONF_SUPPORT_DEFAULT
default 0
export always
comment "enable mmconfig for pci conf"
end
-define MMCONF_BASE_ADDRESS
+define CONFIG_MMCONF_BASE_ADDRESS
default none
format "0x%x"
export used
comment "enable mmconfig base address"
end
-define HW_MEM_HOLE_SIZEK
+define CONFIG_HW_MEM_HOLE_SIZEK
default 0
export always
comment "Opteron E0 later memory hole size in K, 0 mean disable"
end
-define HW_MEM_HOLE_SIZE_AUTO_INC
+define CONFIG_HW_MEM_HOLE_SIZE_AUTO_INC
default 0
export always
comment "Opteron E0 later memory hole size auto increase to avoid hole startk equal to basek"
comment "using hole in MTRR instead of increasing method"
end
-define K8_HT_FREQ_1G_SUPPORT
+define CONFIG_K8_HT_FREQ_1G_SUPPORT
default 0
export always
comment "Optern E0 later could support 1G HT, but still depends MB design"
end
-define K8_REV_F_SUPPORT
+define CONFIG_K8_REV_F_SUPPORT
default 0
export always
comment "Opteron Rev F (DDR2) support"
end
-define CBB
+define CONFIG_CBB
default 0
export always
comment "Opteron cpu bus num base"
end
-define CDB
+define CONFIG_CDB
default 0x18
export always
comment "Opteron cpu device num base"
end
-define HT3_SUPPORT
+define CONFIG_HT3_SUPPORT
default 0
export always
comment "Hypertransport 3 support, include ac HT and unganged sublink feature"
end
-define EXT_RT_TBL_SUPPORT
+define CONFIG_EXT_RT_TBL_SUPPORT
default 0
export always
comment "support AMD family 10 extended routing table via F0x158, normally is enabled when node nums is greater than 8"
end
-define EXT_CONF_SUPPORT
+define CONFIG_EXT_CONF_SUPPORT
default 0
export always
comment "support AMD family 10 extended config space for ram, bus, io, mmio via F1x110, normally is enabled when HT3 is enabled and non ht chain nums is greater than 4"
end
-define DIMM_SUPPORT
+define CONFIG_DIMM_SUPPORT
default 0x0108
format "0x%x"
export always
comment "DIMM support: bit 0 - sdram, bit 1: ddr1, bit 2: ddr2, bit 3: ddr3, bit 4: fbdimm, bit 8: reg"
end
-define CPU_SOCKET_TYPE
+define CONFIG_CPU_SOCKET_TYPE
default 0x10
export always
comment "cpu socket type, 0x10 mean Socket F, 0x11 mean socket M2, 0x20, Soxket G, and 0x21 mean socket M3"
end
-define CPU_ADDR_BITS
+define CONFIG_CPU_ADDR_BITS
default 36
export always
comment "CPU hardware address lines num, for AMD K8 could be 40, and AMD family 10 could be 48"
comment "use AMD MCT to init RAM instead of native code"
end
-define AMD_UCODE_PATCH_FILE
+define CONFIG_AMD_UCODE_PATCH_FILE
default none
export used
format "\"%s\""
comment "name of the microcode patch file"
end
-define K8_MEM_BANK_B_ONLY
+define CONFIG_K8_MEM_BANK_B_ONLY
default 0
export always
comment "use AMD K8's memory bank B only to make a 64bit memory system and memory bank A is free, such as Filbert."
comment "GFX UMA"
end
-define HAVE_MAINBOARD_RESOURCES
+define CONFIG_HAVE_MAINBOARD_RESOURCES
default 0
export always
comment "Enable if the mainboard/chipset requires extra entries in the memory map"
end
-define HAVE_LOW_TABLES
+define CONFIG_HAVE_LOW_TABLES
default 1
export always
comment "Enable if ACPI, PIRQ, MP tables are supposed to live in the low megabyte"
end
-define HAVE_HIGH_TABLES
+define CONFIG_HAVE_HIGH_TABLES
default 0
export always
comment "Enable if ACPI, PIRQ, MP tables are supposed to live at top of memory"
/*
* Memory map:
*
- * DCACHE_RAM_BASE
+ * CONFIG_DCACHE_RAM_BASE
* : data segment
* : bss segment
* : heap
SECTIONS
{
- . = DCACHE_RAM_BASE;
+ . = CONFIG_DCACHE_RAM_BASE;
/*
* First we place the code and read only data (typically const declared).
* This get placed in rom.
_ram_seg = _text;
_eram_seg = _eheap;
- _bogus = ASSERT( ( _eram_seg <= ((DCACHE_RAM_BASE + DCACHE_RAM_SIZE - DCACHE_RAM_GLOBAL_VAR_SIZE))) , "coreboot_apc is too big");
+ _bogus = ASSERT( ( _eram_seg <= ((CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE))) , "coreboot_apc is too big");
/DISCARD/ : {
*(.comment)
/*
* Memory map:
*
- * _RAMBASE
+ * CONFIG_RAMBASE
* : data segment
* : bss segment
* : heap
SECTIONS
{
- . = _RAMBASE;
+ . = CONFIG_RAMBASE;
/*
* First we place the code and read only data (typically const declared).
* This get placed in rom.
}
_ebss = .;
_end = .;
- . = ALIGN(STACK_SIZE);
+ . = ALIGN(CONFIG_STACK_SIZE);
_stack = .;
.stack . : {
/* Reserve a stack for each possible cpu */
/* the stack for ap will be put after pgtbl in 1M to CONFIG_LB_MEM_TOPK range when VGA and ROM_RUN and CONFIG_LB_MEM_TOPK>1024*/
- . = ((CONFIG_CONSOLE_VGA || CONFIG_PCI_ROM_RUN)&&(_RAMBASE<0x100000)&&(CONFIG_LB_MEM_TOPK>(0x100000>>10)) ) ? STACK_SIZE : (CONFIG_MAX_CPUS*STACK_SIZE);
+ . = ((CONFIG_CONSOLE_VGA || CONFIG_PCI_ROM_RUN)&&(CONFIG_RAMBASE<0x100000)&&(CONFIG_LB_MEM_TOPK>(0x100000>>10)) ) ? CONFIG_STACK_SIZE : (CONFIG_MAX_CPUS*CONFIG_STACK_SIZE);
}
_estack = .;
_heap = .;
.heap . : {
- /* Reserve HEAP_SIZE bytes for the heap */
- . = HEAP_SIZE ;
+ /* Reserve CONFIG_HEAP_SIZE bytes for the heap */
+ . = CONFIG_HEAP_SIZE ;
. = ALIGN(4);
}
_eheap = .;
_bogus = ASSERT( ( (_eram_seg>>10) < (CONFIG_LB_MEM_TOPK)) , "please increase CONFIG_LB_MEM_TOPK");
- _bogus = ASSERT( !((CONFIG_CONSOLE_VGA || CONFIG_PCI_ROM_RUN) && ((_ram_seg<0xa0000) && (_eram_seg>0xa0000))) , "please increase CONFIG_LB_MEM_TOPK and if still fail, try to set _RAMBASE more than 1M");
+ _bogus = ASSERT( !((CONFIG_CONSOLE_VGA || CONFIG_PCI_ROM_RUN) && ((_ram_seg<0xa0000) && (_eram_seg>0xa0000))) , "please increase CONFIG_LB_MEM_TOPK and if still fail, try to set CONFIG_RAMBASE more than 1M");
/DISCARD/ : {
*(.comment)
## Compute the location and size of where this firmware image
## (coreboot plus bootloader) will live in the boot rom chip.
##
-if USE_FAILOVER_IMAGE
- default ROM_SECTION_SIZE = FAILOVER_SIZE
- default ROM_SECTION_OFFSET = ( ROM_SIZE - FAILOVER_SIZE )
+if CONFIG_USE_FAILOVER_IMAGE
+ default CONFIG_ROM_SECTION_SIZE = CONFIG_FAILOVER_SIZE
+ default CONFIG_ROM_SECTION_OFFSET = ( CONFIG_ROM_SIZE - CONFIG_FAILOVER_SIZE )
else
- if USE_FALLBACK_IMAGE
- default ROM_SECTION_SIZE = FALLBACK_SIZE
- default ROM_SECTION_OFFSET = ( ROM_SIZE - FALLBACK_SIZE - FAILOVER_SIZE )
+ if CONFIG_USE_FALLBACK_IMAGE
+ default CONFIG_ROM_SECTION_SIZE = CONFIG_FALLBACK_SIZE
+ default CONFIG_ROM_SECTION_OFFSET = ( CONFIG_ROM_SIZE - CONFIG_FALLBACK_SIZE - CONFIG_FAILOVER_SIZE )
else
if CONFIG_CBFS
- default ROM_SECTION_SIZE = FALLBACK_SIZE
- default ROM_SECTION_OFFSET = ( ROM_SIZE - FALLBACK_SIZE - FALLBACK_SIZE - FAILOVER_SIZE )
+ default CONFIG_ROM_SECTION_SIZE = CONFIG_FALLBACK_SIZE
+ default CONFIG_ROM_SECTION_OFFSET = ( CONFIG_ROM_SIZE - CONFIG_FALLBACK_SIZE - CONFIG_FALLBACK_SIZE - CONFIG_FAILOVER_SIZE )
else
- default ROM_SECTION_SIZE = ( ROM_SIZE - FALLBACK_SIZE - FAILOVER_SIZE )
- default ROM_SECTION_OFFSET = 0
+ default CONFIG_ROM_SECTION_SIZE = ( CONFIG_ROM_SIZE - CONFIG_FALLBACK_SIZE - CONFIG_FAILOVER_SIZE )
+ default CONFIG_ROM_SECTION_OFFSET = 0
end
end
end
## Compute the start location and size size of
## The coreboot bootloader.
##
-default PAYLOAD_SIZE = ( ROM_SECTION_SIZE - ROM_IMAGE_SIZE )
-default CONFIG_ROM_PAYLOAD_START = (0xffffffff - ROM_SIZE + ROM_SECTION_OFFSET + 1)
+default CONFIG_PAYLOAD_SIZE = ( CONFIG_ROM_SECTION_SIZE - CONFIG_ROM_IMAGE_SIZE )
+default CONFIG_ROM_PAYLOAD_START = (0xffffffff - CONFIG_ROM_SIZE + CONFIG_ROM_SECTION_OFFSET + 1)
##
## Compute where this copy of coreboot will start in the boot rom
##
-default _ROMBASE = ( CONFIG_ROM_PAYLOAD_START + PAYLOAD_SIZE )
+default CONFIG_ROMBASE = ( CONFIG_ROM_PAYLOAD_START + CONFIG_PAYLOAD_SIZE )
##
## Compute a range of ROM that can cached to speed up coreboot,
## execution speed.
##
-## XIP_ROM_SIZE must be a power of 2 and is set in mainboard Config.lb
-## XIP_ROM_BASE must be a multiple of XIP_ROM_SIZE
+## CONFIG_XIP_ROM_SIZE must be a power of 2 and is set in mainboard Config.lb
+## CONFIG_XIP_ROM_BASE must be a multiple of CONFIG_XIP_ROM_SIZE
##
-if USE_FAILOVER_IMAGE
- default XIP_ROM_BASE = ( _ROMBASE - XIP_ROM_SIZE + ROM_IMAGE_SIZE)
+if CONFIG_USE_FAILOVER_IMAGE
+ default CONFIG_XIP_ROM_BASE = ( CONFIG_ROMBASE - CONFIG_XIP_ROM_SIZE + CONFIG_ROM_IMAGE_SIZE)
else
- if USE_FALLBACK_IMAGE
- default XIP_ROM_BASE = ( _ROMBASE - XIP_ROM_SIZE + ROM_IMAGE_SIZE + FAILOVER_SIZE)
+ if CONFIG_USE_FALLBACK_IMAGE
+ default CONFIG_XIP_ROM_BASE = ( CONFIG_ROMBASE - CONFIG_XIP_ROM_SIZE + CONFIG_ROM_IMAGE_SIZE + CONFIG_FAILOVER_SIZE)
else
- default XIP_ROM_BASE = ( _ROMBASE - XIP_ROM_SIZE + ROM_IMAGE_SIZE)
+ default CONFIG_XIP_ROM_BASE = ( CONFIG_ROMBASE - CONFIG_XIP_ROM_SIZE + CONFIG_ROM_IMAGE_SIZE)
end
end
## Compute the location and size of where this firmware image
## (coreboot plus bootloader) will live in the boot rom chip.
##
-if USE_FALLBACK_IMAGE
- default ROM_SECTION_SIZE = FALLBACK_SIZE
- default ROM_SECTION_OFFSET = ( ROM_SIZE - FALLBACK_SIZE )
+if CONFIG_USE_FALLBACK_IMAGE
+ default CONFIG_ROM_SECTION_SIZE = CONFIG_FALLBACK_SIZE
+ default CONFIG_ROM_SECTION_OFFSET = ( CONFIG_ROM_SIZE - CONFIG_FALLBACK_SIZE )
else
if CONFIG_CBFS
- default ROM_SECTION_SIZE = FALLBACK_SIZE
- default ROM_SECTION_OFFSET = ( ROM_SIZE - FALLBACK_SIZE - FALLBACK_SIZE )
+ default CONFIG_ROM_SECTION_SIZE = CONFIG_FALLBACK_SIZE
+ default CONFIG_ROM_SECTION_OFFSET = ( CONFIG_ROM_SIZE - CONFIG_FALLBACK_SIZE - CONFIG_FALLBACK_SIZE )
else
- default ROM_SECTION_SIZE = ( ROM_SIZE - FALLBACK_SIZE )
- default ROM_SECTION_OFFSET = 0
+ default CONFIG_ROM_SECTION_SIZE = ( CONFIG_ROM_SIZE - CONFIG_FALLBACK_SIZE )
+ default CONFIG_ROM_SECTION_OFFSET = 0
end
end
## Compute the start location and size size of
## The coreboot bootloader.
##
-default PAYLOAD_SIZE = ( ROM_SECTION_SIZE - ROM_IMAGE_SIZE )
-default CONFIG_ROM_PAYLOAD_START = (0xffffffff - ROM_SIZE + ROM_SECTION_OFFSET + 1)
+default CONFIG_PAYLOAD_SIZE = ( CONFIG_ROM_SECTION_SIZE - CONFIG_ROM_IMAGE_SIZE )
+default CONFIG_ROM_PAYLOAD_START = (0xffffffff - CONFIG_ROM_SIZE + CONFIG_ROM_SECTION_OFFSET + 1)
##
## Compute where this copy of coreboot will start in the boot rom
##
-default _ROMBASE = ( CONFIG_ROM_PAYLOAD_START + PAYLOAD_SIZE )
+default CONFIG_ROMBASE = ( CONFIG_ROM_PAYLOAD_START + CONFIG_PAYLOAD_SIZE )
##
## Compute a range of ROM that can cached to speed up coreboot,
## execution speed.
##
-## XIP_ROM_SIZE must be a power of 2 and is set in mainboard Config.lb
-## XIP_ROM_BASE must be a multiple of XIP_ROM_SIZE
+## CONFIG_XIP_ROM_SIZE must be a power of 2 and is set in mainboard Config.lb
+## CONFIG_XIP_ROM_BASE must be a multiple of CONFIG_XIP_ROM_SIZE
##
-default XIP_ROM_BASE = ( _ROMBASE - XIP_ROM_SIZE + ROM_IMAGE_SIZE )
+default CONFIG_XIP_ROM_BASE = ( CONFIG_ROMBASE - CONFIG_XIP_ROM_SIZE + CONFIG_ROM_IMAGE_SIZE )
{
struct console_driver *driver;
if(get_option(&console_loglevel, "debug_level"))
- console_loglevel=DEFAULT_CONSOLE_LOGLEVEL;
+ console_loglevel=CONFIG_DEFAULT_CONSOLE_LOGLEVEL;
for(driver = console_drivers; driver < econsole_drivers; driver++) {
if (!driver->init)
*/
void post_code(uint8_t value)
{
-#if !defined(NO_POST) || NO_POST==0
+#if !defined(CONFIG_NO_POST) || CONFIG_NO_POST==0
#if CONFIG_SERIAL_POST==1
printk_emerg("POST: 0x%02x\n", value);
#endif
/* Keep together for sysctl support */
-int console_loglevel = DEFAULT_CONSOLE_LOGLEVEL;
+int console_loglevel = CONFIG_DEFAULT_CONSOLE_LOGLEVEL;
int default_message_loglevel = DEFAULT_MESSAGE_LOGLEVEL;
int minimum_console_loglevel = MINIMUM_CONSOLE_LOGLEVEL;
-int default_console_loglevel = DEFAULT_CONSOLE_LOGLEVEL;
+int default_console_loglevel = CONFIG_DEFAULT_CONSOLE_LOGLEVEL;
void display(char*);
extern int vtxprintf(void (*)(unsigned char), const char *, va_list);
#include <pc80/mc146818rtc.h>
/* Base Address */
-#ifndef TTYS0_BASE
-#define TTYS0_BASE 0x3f8
+#ifndef CONFIG_TTYS0_BASE
+#define CONFIG_TTYS0_BASE 0x3f8
#endif
-#ifndef TTYS0_BAUD
-#define TTYS0_BAUD 115200
+#ifndef CONFIG_TTYS0_BAUD
+#define CONFIG_TTYS0_BAUD 115200
#endif
-#ifndef TTYS0_DIV
-#if ((115200%TTYS0_BAUD) != 0)
+#ifndef CONFIG_TTYS0_DIV
+#if ((115200%CONFIG_TTYS0_BAUD) != 0)
#error Bad ttys0 baud rate
#endif
-#define TTYS0_DIV (115200/TTYS0_BAUD)
+#define CONFIG_TTYS0_DIV (115200/CONFIG_TTYS0_BAUD)
#endif
/* Line Control Settings */
-#ifndef TTYS0_LCS
+#ifndef CONFIG_TTYS0_LCS
/* Set 8bit, 1 stop bit, no parity */
-#define TTYS0_LCS 0x3
+#define CONFIG_TTYS0_LCS 0x3
#endif
-#define UART_LCS TTYS0_LCS
+#define UART_LCS CONFIG_TTYS0_LCS
static void ttyS0_init(void)
{
static const unsigned char div[8]={1,2,3,6,12,24,48,96};
int b_index=0;
- unsigned int divisor=TTYS0_DIV;
+ unsigned int divisor=CONFIG_TTYS0_DIV;
if(get_option(&b_index,"baud_rate")==0) {
divisor=div[b_index];
}
- uart8250_init(TTYS0_BASE, divisor, TTYS0_LCS);
+ uart8250_init(CONFIG_TTYS0_BASE, divisor, CONFIG_TTYS0_LCS);
}
static void ttyS0_tx_byte(unsigned char data)
{
- uart8250_tx_byte(TTYS0_BASE, data);
+ uart8250_tx_byte(CONFIG_TTYS0_BASE, data);
}
static unsigned char ttyS0_rx_byte(void)
{
- return uart8250_rx_byte(TTYS0_BASE);
+ return uart8250_rx_byte(CONFIG_TTYS0_BASE);
}
static int ttyS0_tst_byte(void)
{
- return uart8250_can_rx_byte(TTYS0_BASE);
+ return uart8250_can_rx_byte(CONFIG_TTYS0_BASE);
}
static const struct console_driver uart8250_console __console = {
* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*/
-#define CacheSize DCACHE_RAM_SIZE
+#define CacheSize CONFIG_DCACHE_RAM_SIZE
#define CacheBase (0xd0000 - CacheSize)
/* leave some space for global variable to pass to RAM stage */
-#define GlobalVarSize DCACHE_RAM_GLOBAL_VAR_SIZE
+#define GlobalVarSize CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE
-/* for CAR_FAM10 */
+/* for CONFIG_CAR_FAM10 */
#define CacheSizeAPStack 0x400 /* 1K */
#define MSR_FAM10 0xC001102A
cvtsd2si %xmm3, %ebx
/* hope we can skip the double set for normal part */
-#if ((HAVE_FAILOVER_BOOT == 1) && (USE_FAILOVER_IMAGE == 1)) || ((HAVE_FAILOVER_BOOT == 0) && (USE_FALLBACK_IMAGE == 1))
+#if ((CONFIG_HAVE_FAILOVER_BOOT == 1) && (CONFIG_USE_FAILOVER_IMAGE == 1)) || ((CONFIG_HAVE_FAILOVER_BOOT == 0) && (CONFIG_USE_FALLBACK_IMAGE == 1))
/* check if cpu_init_detected */
movl $MTRRdefType_MSR, %ecx
xorl %edx, %edx
movl $(((CONFIG_LB_MEM_TOPK << 10) + TOP_MEM_MASK) & ~TOP_MEM_MASK) , %eax
wrmsr
-#endif /* USE_FAILOVER_IMAGE == 1*/
+#endif /* CONFIG_USE_FAILOVER_IMAGE == 1*/
-#if ((HAVE_FAILOVER_BOOT == 1) && (USE_FAILOVER_IMAGE == 0)) || ((HAVE_FAILOVER_BOOT == 0) && (USE_FALLBACK_IMAGE == 0))
+#if ((CONFIG_HAVE_FAILOVER_BOOT == 1) && (CONFIG_USE_FAILOVER_IMAGE == 0)) || ((CONFIG_HAVE_FAILOVER_BOOT == 0) && (CONFIG_USE_FALLBACK_IMAGE == 0))
/* disable cache */
movl %cr0, %eax
orl $(1 << 30),%eax
#endif
-#if defined(XIP_ROM_SIZE) && defined(XIP_ROM_BASE)
+#if defined(CONFIG_XIP_ROM_SIZE) && defined(CONFIG_XIP_ROM_BASE)
/* enable write base caching so we can do execute in place
* on the flash rom.
*/
movl $0x202, %ecx
xorl %edx, %edx
- movl $(XIP_ROM_BASE | MTRR_TYPE_WRBACK), %eax
+ movl $(CONFIG_XIP_ROM_BASE | MTRR_TYPE_WRBACK), %eax
wrmsr
movl $0x203, %ecx
- movl $0xff, %edx /* (1 << (CPU_ADDR_BITS - 32)) - 1 for K8 (CPU_ADDR_BITS = 40) */
+ movl $0xff, %edx /* (1 << (CONFIG_CPU_ADDR_BITS - 32)) - 1 for K8 (CONFIG_CPU_ADDR_BITS = 40) */
jmp_if_k8(wbcache_post_fam10_setup)
- movl $0xffff, %edx /* (1 << (CPU_ADDR_BITS - 32)) - 1 for FAM10 (CPU_ADDR_BITS = 48) */
+ movl $0xffff, %edx /* (1 << (CONFIG_CPU_ADDR_BITS - 32)) - 1 for FAM10 (CONFIG_CPU_ADDR_BITS = 48) */
wbcache_post_fam10_setup:
- movl $(~(XIP_ROM_SIZE - 1) | 0x800), %eax
+ movl $(~(CONFIG_XIP_ROM_SIZE - 1) | 0x800), %eax
wrmsr
-#endif /* XIP_ROM_SIZE && XIP_ROM_BASE */
+#endif /* CONFIG_XIP_ROM_SIZE && CONFIG_XIP_ROM_BASE */
-#if ((HAVE_FAILOVER_BOOT == 1) && (USE_FAILOVER_IMAGE == 1)) || ((HAVE_FAILOVER_BOOT == 0) && (USE_FALLBACK_IMAGE == 1))
+#if ((CONFIG_HAVE_FAILOVER_BOOT == 1) && (CONFIG_USE_FAILOVER_IMAGE == 1)) || ((CONFIG_HAVE_FAILOVER_BOOT == 0) && (CONFIG_USE_FALLBACK_IMAGE == 1))
/* Set the default memory type and enable fixed and variable MTRRs */
movl $MTRRdefType_MSR, %ecx
xorl %edx, %edx
movb $0xA2, %al
outb %al, $0x80
-#if ((HAVE_FAILOVER_BOOT == 1) && (USE_FAILOVER_IMAGE == 1)) || ((HAVE_FAILOVER_BOOT == 0) && (USE_FALLBACK_IMAGE == 1))
+#if ((CONFIG_HAVE_FAILOVER_BOOT == 1) && (CONFIG_USE_FAILOVER_IMAGE == 1)) || ((CONFIG_HAVE_FAILOVER_BOOT == 0) && (CONFIG_USE_FALLBACK_IMAGE == 1))
/* Read the range with lodsl*/
cld
movl $CacheBase, %esi
xorl %eax, %eax
rep stosl
-#endif /*USE_FAILOVER_IMAGE == 1*/
+#endif /*CONFIG_USE_FAILOVER_IMAGE == 1*/
/* set up the stack pointer */
movl $(CacheBase + CacheSize - GlobalVarSize), %eax
// will reuse %edi as 0 from clear_memory for copy_and_run part, actually it is increased already
// so noline clear_init_ram
-#if HAVE_ACPI_RESUME == 1
+#if CONFIG_HAVE_ACPI_RESUME == 1
/* clear only coreboot used region of memory. Note: this may break ECC enabled boards */
- clear_memory( _RAMBASE, (CONFIG_LB_MEM_TOPK << 10) - _RAMBASE - DCACHE_RAM_SIZE);
+ clear_memory( CONFIG_RAMBASE, (CONFIG_LB_MEM_TOPK << 10) - CONFIG_RAMBASE - CONFIG_DCACHE_RAM_SIZE);
#else
- clear_memory(0, ((CONFIG_LB_MEM_TOPK<<10) - DCACHE_RAM_SIZE));
+ clear_memory(0, ((CONFIG_LB_MEM_TOPK<<10) - CONFIG_DCACHE_RAM_SIZE));
#endif
}
static void copy_and_run(void)
{
-# if USE_FALLBACK_IMAGE == 1
+# if CONFIG_USE_FALLBACK_IMAGE == 1
cbfs_and_run_core("fallback/coreboot_ram", 0);
# else
cbfs_and_run_core("normal/coreboot_ram", 0);
static void copy_and_run_ap_code_in_car(unsigned ret_addr)
{
-# if USE_FALLBACK_IMAGE == 1
+# if CONFIG_USE_FALLBACK_IMAGE == 1
cbfs_and_run_core("fallback/coreboot_apc", ret_addr);
# else
cbfs_and_run_core("normal/coreboot_apc", ret_addr);
"xorl %edx, %edx\n\t"
"xorl %eax, %eax\n\t"
"wrmsr\n\t"
-#if DCACHE_RAM_SIZE > 0x8000
+#if CONFIG_DCACHE_RAM_SIZE > 0x8000
"movl $0x268, %ecx\n\t" /* fix4k_c0000*/
"wrmsr\n\t"
#endif
set_init_ram_access(); /* So we can access RAM from [1M, CONFIG_LB_MEM_TOPK) */
-// dump_mem(DCACHE_RAM_BASE+DCACHE_RAM_SIZE-0x8000, DCACHE_RAM_BASE+DCACHE_RAM_SIZE-0x7c00);
+// dump_mem(CONFIG_DCACHE_RAM_BASE+CONFIG_DCACHE_RAM_SIZE-0x8000, CONFIG_DCACHE_RAM_BASE+CONFIG_DCACHE_RAM_SIZE-0x7c00);
print_debug("Copying data from cache to RAM -- switching to use RAM as stack... ");
/* from here don't store more data in CAR */
);
#endif
- memcopy((void *)((CONFIG_LB_MEM_TOPK<<10)-DCACHE_RAM_SIZE), (void *)DCACHE_RAM_BASE, DCACHE_RAM_SIZE); //inline
+ memcopy((void *)((CONFIG_LB_MEM_TOPK<<10)-CONFIG_DCACHE_RAM_SIZE), (void *)CONFIG_DCACHE_RAM_BASE, CONFIG_DCACHE_RAM_SIZE); //inline
// dump_mem((CONFIG_LB_MEM_TOPK<<10) - 0x8000, (CONFIG_LB_MEM_TOPK<<10) - 0x7c00);
__asm__ volatile (
- /* set new esp */ /* before _RAMBASE */
+ /* set new esp */ /* before CONFIG_RAMBASE */
"subl %0, %%ebp\n\t"
"subl %0, %%esp\n\t"
- ::"a"( (DCACHE_RAM_BASE + DCACHE_RAM_SIZE)- (CONFIG_LB_MEM_TOPK<<10) )
+ ::"a"( (CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE)- (CONFIG_LB_MEM_TOPK<<10) )
); // We need to push %eax to the stack (CAR) before copy stack and pop it later after copy stack and change esp
#if 0
__asm__ volatile (
disable_cache_as_ram_bsp();
print_debug("Clearing initial memory region: ");
- clear_init_ram(); //except the range from [(CONFIG_LB_MEM_TOPK<<10) - DCACHE_RAM_SIZE, (CONFIG_LB_MEM_TOPK<<10))
+ clear_init_ram(); //except the range from [(CONFIG_LB_MEM_TOPK<<10) - CONFIG_DCACHE_RAM_SIZE, (CONFIG_LB_MEM_TOPK<<10))
print_debug("Done\r\n");
// dump_mem((CONFIG_LB_MEM_TOPK<<10) - 0x8000, (CONFIG_LB_MEM_TOPK<<10) - 0x7c00);
-#ifndef MEM_TRAIN_SEQ
-#define MEM_TRAIN_SEQ 0
+#ifndef CONFIG_MEM_TRAIN_SEQ
+#define CONFIG_MEM_TRAIN_SEQ 0
#endif
set_sysinfo_in_ram(1); // So other core0 could start to train mem
-#if MEM_TRAIN_SEQ == 1
-// struct sys_info *sysinfox = ((CONFIG_LB_MEM_TOPK<<10) - DCACHE_RAM_GLOBAL_VAR_SIZE);
+#if CONFIG_MEM_TRAIN_SEQ == 1
+// struct sys_info *sysinfox = ((CONFIG_LB_MEM_TOPK<<10) - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE);
// wait for ap memory to trained
// wait_all_core0_mem_trained(sysinfox); // moved to lapic_init_cpus.c
if((apicid_base+ioapic_num-1)>0xf) {
// We need to enable APIC EXT ID
- printk_info("if the IO APIC device doesn't support 256 apic id, \r\n you need to set ENABLE_APIC_EXT_ID in auto.c so you can spare 16 id for ioapic\r\n");
+ printk_info("if the IO APIC device doesn't support 256 apic id, \r\n you need to set CONFIG_ENABLE_APIC_EXT_ID in auto.c so you can spare 16 id for ioapic\r\n");
enable_apic_ext_id(nodes);
}
#if SET_NB_CFG_54 == 1
static inline uint8_t set_apicid_cpuid_lo(void)
{
-#if K8_REV_F_SUPPORT == 0
+#if CONFIG_K8_REV_F_SUPPORT == 0
if(is_cpu_pre_e0()) return 0; // pre_e0 can not be set
#endif
unsigned nodes;
unsigned nodeid;
- if (HAVE_OPTION_TABLE &&
+ if (CONFIG_HAVE_OPTION_TABLE &&
read_option(CMOS_VSTART_dual_core, CMOS_VLEN_dual_core, 0) != 0) {
return; // disable dual_core
}
}
}
-#if USE_DCACHE_RAM == 0
+#if CONFIG_USE_DCACHE_RAM == 0
static void do_k8_init_and_stop_secondaries(void)
{
struct node_core_id id;
pci_write_config32(dev_f0, 0x68, val);
/* Set the lapicid */
- #if (ENABLE_APIC_EXT_ID == 1)
+ #if (CONFIG_ENABLE_APIC_EXT_ID == 1)
unsigned initial_apicid = get_initial_apicid();
- #if LIFT_BSP_APIC_ID == 0
+ #if CONFIG_LIFT_BSP_APIC_ID == 0
if( initial_apicid != 0 ) // other than bsp
#endif
{
/* use initial apic id to lift it */
uint32_t dword = lapic_read(LAPIC_ID);
dword &= ~(0xff<<24);
- dword |= (((initial_apicid + APIC_ID_OFFSET) & 0xff)<<24);
+ dword |= (((initial_apicid + CONFIG_APIC_ID_OFFSET) & 0xff)<<24);
lapic_write(LAPIC_ID, dword);
}
- #if LIFT_BSP_APIC_ID == 1
- bsp_apicid += APIC_ID_OFFSET;
+ #if CONFIG_LIFT_BSP_APIC_ID == 1
+ bsp_apicid += CONFIG_APIC_ID_OFFSET;
#endif
#endif
# Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
#
-uses HAVE_INIT_TIMER
-uses HAVE_MOVNTI
-uses CPU_ADDR_BITS
+uses CONFIG_HAVE_INIT_TIMER
+uses CONFIG_HAVE_MOVNTI
+uses CONFIG_CPU_ADDR_BITS
-default HAVE_INIT_TIMER=1
-default HAVE_MOVNTI=1
-default CPU_ADDR_BITS=48
+default CONFIG_HAVE_INIT_TIMER=1
+default CONFIG_HAVE_MOVNTI=1
+default CONFIG_CPU_ADDR_BITS=48
dir /cpu/x86/tsc
dir /cpu/x86/fpu
dir /cpu/x86/mmx
#include "defaults.h"
-//it takes the ENABLE_APIC_EXT_ID and APIC_ID_OFFSET and LIFT_BSP_APIC_ID
+//it takes the CONFIG_ENABLE_APIC_EXT_ID and CONFIG_APIC_ID_OFFSET and CONFIG_LIFT_BSP_APIC_ID
#ifndef FAM10_SET_FIDVID
#define FAM10_SET_FIDVID 1
#endif
static void init_fidvid_stage2(u32 apicid, u32 nodeid);
void cpuSetAMDMSR(void);
-#if PCI_IO_CFG_EXT == 1
+#if CONFIG_PCI_IO_CFG_EXT == 1
static void set_EnableCf8ExtCfg(void)
{
// set the NB_CFG[46]=1;
msr_t msr;
msr = rdmsr(NB_CFG_MSR);
- // EnableCf8ExtCfg: We need that to access PCI_IO_CFG_EXT 4K range
+ // EnableCf8ExtCfg: We need that to access CONFIG_PCI_IO_CFG_EXT 4K range
msr.hi |= (1<<(46-32));
wrmsr(NB_CFG_MSR, msr);
}
static void set_pci_mmio_conf_reg(void)
{
-#if MMCONF_SUPPORT
+#if CONFIG_MMCONF_SUPPORT
msr_t msr;
msr = rdmsr(0xc0010058);
msr.lo &= ~(0xfff00000 | (0xf << 2));
// 256 bus per segment, MMIO reg will be 4G , enable MMIO Config space
- msr.lo |= ((8+PCI_BUS_SEGN_BITS) << 2) | (1 << 0);
+ msr.lo |= ((8+CONFIG_PCI_BUS_SEGN_BITS) << 2) | (1 << 0);
msr.hi &= ~(0x0000ffff);
msr.hi |= (PCI_MMIO_BASE >> (32-8));
wrmsr(0xc0010058, msr); // MMIO Config Base Address Reg
for (j = jstart; j <= jend; j++) {
ap_apicid = i * (nb_cfg_54 ? (siblings + 1):1) + j * (nb_cfg_54 ? 1:64);
- #if (ENABLE_APIC_EXT_ID == 1) && (APIC_ID_OFFSET > 0)
- #if LIFT_BSP_APIC_ID == 0
+ #if (CONFIG_ENABLE_APIC_EXT_ID == 1) && (CONFIG_APIC_ID_OFFSET > 0)
+ #if CONFIG_LIFT_BSP_APIC_ID == 0
if( (i != 0) || (j != 0)) /* except bsp */
#endif
- ap_apicid += APIC_ID_OFFSET;
+ ap_apicid += CONFIG_APIC_ID_OFFSET;
#endif
if(ap_apicid == bsp_apicid) continue;
}
-#ifndef MEM_TRAIN_SEQ
-#define MEM_TRAIN_SEQ 0
+#ifndef CONFIG_MEM_TRAIN_SEQ
+#define CONFIG_MEM_TRAIN_SEQ 0
#endif
#if RAMINIT_SYSINFO == 1
if(id.coreid == 0) {
set_apicid_cpuid_lo(); /* only set it on core0 */
set_EnableCf8ExtCfg(); /* only set it on core0 */
- #if (ENABLE_APIC_EXT_ID == 1)
+ #if (CONFIG_ENABLE_APIC_EXT_ID == 1)
enable_apic_ext_id(id.nodeid);
#endif
}
enable_lapic();
-#if (ENABLE_APIC_EXT_ID == 1) && (APIC_ID_OFFSET > 0)
+#if (CONFIG_ENABLE_APIC_EXT_ID == 1) && (CONFIG_APIC_ID_OFFSET > 0)
u32 initial_apicid = get_initial_apicid();
- #if LIFT_BSP_APIC_ID == 0
+ #if CONFIG_LIFT_BSP_APIC_ID == 0
if( initial_apicid != 0 ) // other than bsp
#endif
{
/* use initial apic id to lift it */
u32 dword = lapic_read(LAPIC_ID);
dword &= ~(0xff << 24);
- dword |= (((initial_apicid + APIC_ID_OFFSET) & 0xff) << 24);
+ dword |= (((initial_apicid + CONFIG_APIC_ID_OFFSET) & 0xff) << 24);
lapic_write(LAPIC_ID, dword);
}
- #if LIFT_BSP_APIC_ID == 1
- bsp_apicid += APIC_ID_OFFSET;
+ #if CONFIG_LIFT_BSP_APIC_ID == 1
+ bsp_apicid += CONFIG_APIC_ID_OFFSET;
#endif
#endif
/* Enable routing table */
printk_debug("Start node %02x", node);
-#if CAR_FAM10 == 1
- /* For CAR_FAM10 support, we need to set Dram base/limit for the new node */
+#if CONFIG_CAR_FAM10 == 1
+ /* For CONFIG_CAR_FAM10 support, we need to set Dram base/limit for the new node */
pci_write_config32(NODE_MP(node), 0x44, 0);
pci_write_config32(NODE_MP(node), 0x40, 3);
#endif
* 00100F62h (DA-C2) 1062h 0100009Fh
*/
-#include AMD_UCODE_PATCH_FILE
+#include CONFIG_AMD_UCODE_PATCH_FILE
#endif
/* Dummy terminator */
-uses HAVE_INIT_TIMER
-uses HAVE_MOVNTI
-uses CPU_ADDR_BITS
+uses CONFIG_HAVE_INIT_TIMER
+uses CONFIG_HAVE_MOVNTI
+uses CONFIG_CPU_ADDR_BITS
-default HAVE_INIT_TIMER=1
-default HAVE_MOVNTI=1
-default CPU_ADDR_BITS=40
+default CONFIG_HAVE_INIT_TIMER=1
+default CONFIG_HAVE_MOVNTI=1
+default CONFIG_CPU_ADDR_BITS=40
dir /cpu/x86/tsc
dir /cpu/x86/fpu
dir /cpu/x86/mmx
// dword = 0x00070000; /* enable FID/VID change */
pci_write_config32(PCI_DEV(0, 0x18+i, 3), 0x80, dword);
-#if HAVE_ACPI_RESUME
+#if CONFIG_HAVE_ACPI_RESUME
dword = 0x21132113;
#else
dword = 0x00132113;
-//it takes the ENABLE_APIC_EXT_ID and APIC_ID_OFFSET and LIFT_BSP_APIC_ID
+//it takes the CONFIG_ENABLE_APIC_EXT_ID and CONFIG_APIC_ID_OFFSET and CONFIG_LIFT_BSP_APIC_ID
#ifndef K8_SET_FIDVID
- #if K8_REV_F_SUPPORT == 0
+ #if CONFIG_K8_REV_F_SUPPORT == 0
#define K8_SET_FIDVID 0
#else
// for rev F, need to set FID to max
nodes = get_nodes();
disable_siblings = !CONFIG_LOGICAL_CPUS;
-#if CONFIG_LOGICAL_CPUS == 1 && HAVE_OPTION_TABLE == 1
+#if CONFIG_LOGICAL_CPUS == 1 && CONFIG_HAVE_OPTION_TABLE == 1
if(read_option(CMOS_VSTART_dual_core, CMOS_VLEN_dual_core, 0) != 0) { // 0 mean dual core
disable_siblings = 1;
}
j = ((pci_read_config32(PCI_DEV(0, 0x18+i, 3), 0xe8) >> 12) & 3);
if(nb_cfg_54) {
if(j == 0 ){ // if it is single core, we need to increase siblings for apic calculation
- #if K8_REV_F_SUPPORT == 0
+ #if CONFIG_K8_REV_F_SUPPORT == 0
e0_later_single_core = is_e0_later_in_bsp(i); // single core
#else
e0_later_single_core = is_cpu_f0_in_bsp(i); // We can read cpuid(1) from Func3
ap_apicid = i * (nb_cfg_54?(siblings+1):1) + j * (nb_cfg_54?1:8);
- #if (ENABLE_APIC_EXT_ID == 1)
- #if LIFT_BSP_APIC_ID == 0
+ #if (CONFIG_ENABLE_APIC_EXT_ID == 1)
+ #if CONFIG_LIFT_BSP_APIC_ID == 0
if( (i!=0) || (j!=0)) /* except bsp */
#endif
- ap_apicid += APIC_ID_OFFSET;
+ ap_apicid += CONFIG_APIC_ID_OFFSET;
#endif
if(ap_apicid == bsp_apicid) continue;
stop_this_cpu(); // inline, it will stop all cores except node0/core0 the bsp ....
}
-#ifndef MEM_TRAIN_SEQ
-#define MEM_TRAIN_SEQ 0
+#ifndef CONFIG_MEM_TRAIN_SEQ
+#define CONFIG_MEM_TRAIN_SEQ 0
#endif
-#if MEM_TRAIN_SEQ == 1
+#if CONFIG_MEM_TRAIN_SEQ == 1
static inline void train_ram_on_node(unsigned nodeid, unsigned coreid, struct sys_info *sysinfo, unsigned retcall);
#endif
/* NB_CFG MSR is shared between cores, so we need make sure core0 is done at first --- use wait_all_core0_started */
if(id.coreid == 0) {
set_apicid_cpuid_lo(); /* only set it on core0 */
- #if ENABLE_APIC_EXT_ID == 1
+ #if CONFIG_ENABLE_APIC_EXT_ID == 1
enable_apic_ext_id(id.nodeid);
#endif
}
enable_lapic();
// init_timer(); // We need TMICT to pass msg for FID/VID change
- #if (ENABLE_APIC_EXT_ID == 1)
+ #if (CONFIG_ENABLE_APIC_EXT_ID == 1)
unsigned initial_apicid = get_initial_apicid();
- #if LIFT_BSP_APIC_ID == 0
+ #if CONFIG_LIFT_BSP_APIC_ID == 0
if( initial_apicid != 0 ) // other than bsp
#endif
{
/* use initial apic id to lift it */
uint32_t dword = lapic_read(LAPIC_ID);
dword &= ~(0xff<<24);
- dword |= (((initial_apicid + APIC_ID_OFFSET) & 0xff)<<24);
+ dword |= (((initial_apicid + CONFIG_APIC_ID_OFFSET) & 0xff)<<24);
lapic_write(LAPIC_ID, dword);
}
- #if LIFT_BSP_APIC_ID == 1
- bsp_apicid += APIC_ID_OFFSET;
+ #if CONFIG_LIFT_BSP_APIC_ID == 1
+ bsp_apicid += CONFIG_APIC_ID_OFFSET;
#endif
#endif
}
lapic_write(LAPIC_MSG_REG, (apicid<<24) | 0x44); // bsp can not check it before stop_this_cpu
set_init_ram_access();
- #if MEM_TRAIN_SEQ == 1
+ #if CONFIG_MEM_TRAIN_SEQ == 1
train_ram_on_node(id.nodeid, id.coreid, sysinfo, STOP_CAR_AND_CPU);
#endif
void cpus_ready_for_init(void)
{
-#if MEM_TRAIN_SEQ == 1
- struct sys_info *sysinfox = (struct sys_info *)((CONFIG_LB_MEM_TOPK<<10) - DCACHE_RAM_GLOBAL_VAR_SIZE);
+#if CONFIG_MEM_TRAIN_SEQ == 1
+ struct sys_info *sysinfox = (struct sys_info *)((CONFIG_LB_MEM_TOPK<<10) - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE);
// wait for ap memory to trained
wait_all_core0_mem_trained(sysinfox);
#endif
}
-#if K8_REV_F_SUPPORT == 0
+#if CONFIG_K8_REV_F_SUPPORT == 0
int is_e0_later_in_bsp(int nodeid)
{
uint32_t val;
}
#endif
-#if K8_REV_F_SUPPORT == 1
+#if CONFIG_K8_REV_F_SUPPORT == 1
int is_cpu_f0_in_bsp(int nodeid)
{
uint32_t dword;
startk = (pci_read_config32(f1_dev, 0x40 + (node_id*8)) & 0xffff0000) >> 2;
endk = ((pci_read_config32(f1_dev, 0x44 + (node_id*8)) & 0xffff0000) >> 2) + 0x4000;
-#if HW_MEM_HOLE_SIZEK != 0
- #if K8_REV_F_SUPPORT == 0
+#if CONFIG_HW_MEM_HOLE_SIZEK != 0
+ #if CONFIG_K8_REV_F_SUPPORT == 0
if (!is_cpu_pre_e0())
{
#endif
if(val & 1) {
hole_startk = ((val & (0xff<<24)) >> 10);
}
- #if K8_REV_F_SUPPORT == 0
+ #if CONFIG_K8_REV_F_SUPPORT == 0
}
#endif
#endif
disable_lapic();
/* Walk through 2M chunks and zero them */
-#if HW_MEM_HOLE_SIZEK != 0
+#if CONFIG_HW_MEM_HOLE_SIZEK != 0
/* here hole_startk can not be equal to begink, never. Also hole_startk is in 2M boundary, 64M? */
if ( (hole_startk != 0) && ((begink < hole_startk) && (endk>(4*1024*1024)))) {
for(basek = begink; basek < hole_startk;
static inline void k8_errata(void)
{
msr_t msr;
-#if K8_REV_F_SUPPORT == 0
+#if CONFIG_K8_REV_F_SUPPORT == 0
if (is_cpu_pre_c0()) {
/* Erratum 63... */
msr = rdmsr(HWCR_MSR);
}
#endif
-#if K8_REV_F_SUPPORT == 0
+#if CONFIG_K8_REV_F_SUPPORT == 0
if (!is_cpu_pre_e0())
#endif
{
msr.lo |= 1 << 6;
wrmsr(HWCR_MSR, msr);
-#if K8_REV_F_SUPPORT == 1
+#if CONFIG_K8_REV_F_SUPPORT == 1
/* Erratum 131... */
msr = rdmsr(NB_CFG_MSR);
msr.lo |= 1 << 20;
unsigned siblings;
#endif
-#if K8_REV_F_SUPPORT == 1
+#if CONFIG_K8_REV_F_SUPPORT == 1
struct cpuinfo_x86 c;
get_fms(&c, dev->device);
};
static struct cpu_device_id cpu_table[] = {
-#if K8_REV_F_SUPPORT == 0
+#if CONFIG_K8_REV_F_SUPPORT == 0
{ X86_VENDOR_AMD, 0xf40 }, /* SH-B0 (socket 754) */
{ X86_VENDOR_AMD, 0xf50 }, /* SH-B0 (socket 940) */
{ X86_VENDOR_AMD, 0xf51 }, /* SH-B3 (socket 940) */
{ X86_VENDOR_AMD, 0x30ff2 }, /* E4 ? */
#endif
-#if K8_REV_F_SUPPORT == 1
+#if CONFIG_K8_REV_F_SUPPORT == 1
/*
* AMD F0 support.
*
static uint8_t microcode_updates[] __attribute__ ((aligned(16))) = {
-#if K8_REV_F_SUPPORT == 0
+#if CONFIG_K8_REV_F_SUPPORT == 0
#include "microcode_rev_c.h"
#include "microcode_rev_d.h"
#include "microcode_rev_e.h"
#endif
-#if K8_REV_F_SUPPORT == 1
+#if CONFIG_K8_REV_F_SUPPORT == 1
// #include "microcode_rev_f.h"
#endif
/* Dummy terminator */
static unsigned get_equivalent_processor_rev_id(unsigned orig_id) {
static unsigned id_mapping_table[] = {
- #if K8_REV_F_SUPPORT == 0
+ #if CONFIG_K8_REV_F_SUPPORT == 0
0x0f48, 0x0048,
0x0f58, 0x0048,
0x20fb1, 0x0210,
#endif
- #if K8_REV_F_SUPPORT == 1
+ #if CONFIG_K8_REV_F_SUPPORT == 1
#endif
cpuid1 = cpuid(0x80000001);
pwr_lmt = ((cpuid1.ebx & 0x1C0) >> 5) | ((cpuid1.ebx & 0x4000) >> 14);
for (index = 0; index <= sizeof(TDP) / sizeof(TDP[0]); index++)
- if (TDP[index].socket_type == CPU_SOCKET_TYPE &&
+ if (TDP[index].socket_type == CONFIG_CPU_SOCKET_TYPE &&
TDP[index].cmp_cap == cmp_cap &&
TDP[index].pwr_lmt == pwr_lmt) {
power_limit = TDP[index].power_limit;
* your mainboard will not be posted on the AMD Recommended Motherboard Website
*/
-#if K8_REV_F_SUPPORT == 0
+#if CONFIG_K8_REV_F_SUPPORT == 0
static char *processor_names[]={
/* 0x00 */ "AMD Engineering Sample",
/* 0x01-0x03 */ NULL, NULL, NULL,
char program_string[48];
unsigned int *program_values = (unsigned int *)program_string;
-#if K8_REV_F_SUPPORT == 0
+#if CONFIG_K8_REV_F_SUPPORT == 0
/* Find out which CPU brand it is */
EightBitBrandId = cpuid_ebx(0x00000001) & 0xff;
BrandId = cpuid_ebx(0x80000001) & 0xffff;
processor_name_string = "AMD Processor model unknown";
#endif
-#if K8_REV_F_SUPPORT == 1
+#if CONFIG_K8_REV_F_SUPPORT == 1
u32 Socket;
u32 CmpCap;
u32 PwrLmt;
for (i=0; i<47; i++) { // 48 -1
if(program_string[i] == program_string[i+1]) {
switch (program_string[i]) {
-#if K8_REV_F_SUPPORT == 0
+#if CONFIG_K8_REV_F_SUPPORT == 0
case 'X': ModelNumber = 22+ NN; break;
case 'Y': ModelNumber = 38 + (2*NN); break;
case 'Z':
case 'V': ModelNumber = 9 + NN; break;
#endif
-#if K8_REV_F_SUPPORT == 1
+#if CONFIG_K8_REV_F_SUPPORT == 1
case 'R': ModelNumber = NN - 1; break;
case 'P': ModelNumber = 26 + NN; break;
case 'T': ModelNumber = 15 + (CmpCap * 10) + NN; break;
//rom = 0xfff80000;
//rom = 0xfffc0000;
/* the VSA starts at the base of rom - 64 */
- rom = ((unsigned long) 0) - (ROM_SIZE + 64*1024);
+ rom = ((unsigned long) 0) - (CONFIG_ROM_SIZE + 64*1024);
buf = (unsigned char *) 0x60000;
olen = unrv2b((uint8_t *)rom, buf, &ilen);
* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*/
-#define LX_STACK_BASE DCACHE_RAM_BASE /* this is where the DCache will be mapped and be used as stack, It would be cool if it was the same base as coreboot normal stack */
-#define LX_STACK_END LX_STACK_BASE+(DCACHE_RAM_SIZE-1)
+#define LX_STACK_BASE CONFIG_DCACHE_RAM_BASE /* this is where the DCache will be mapped and be used as stack, It would be cool if it was the same base as coreboot normal stack */
+#define LX_STACK_END LX_STACK_BASE+(CONFIG_DCACHE_RAM_SIZE-1)
#define LX_NUM_CACHELINES 0x080 /* there are 128lines per way */
#define LX_CACHELINE_SIZE 0x020 /* there are 32bytes per line */
xorl %esi, %esi
xorl %ebp, %ebp
- /* DCache Ways0 through Ways7 will be tagged for LX_STACK_BASE + DCACHE_RAM_SIZE for holding stack */
+ /* DCache Ways0 through Ways7 will be tagged for LX_STACK_BASE + CONFIG_DCACHE_RAM_SIZE for holding stack */
/* remember, there is NO stack yet... */
/* Tell cache we want to fill WAY 0 starting at the top */
mov string, %ebx ; \
CALLSP(crt_console_tx_string)
-# if defined(TTYS0_BASE) && (ASM_CONSOLE_LOGLEVEL > BIOS_DEBUG)
+# if defined(CONFIG_TTYS0_BASE) && (ASM_CONSOLE_LOGLEVEL > BIOS_DEBUG)
# define CONSOLE_DEBUG_TX_STRING(string) __CRT_CONSOLE_TX_STRING(string)
# else
# define CONSOLE_DEBUG_TX_STRING(string)
RETSP
9:
/* Base Address */
-#ifndef TTYS0_BASE
-#define TTYS0_BASE 0x3f8
+#ifndef CONFIG_TTYS0_BASE
+#define CONFIG_TTYS0_BASE 0x3f8
#endif
/* Data */
-#define TTYS0_RBR (TTYS0_BASE+0x00)
+#define TTYS0_RBR (CONFIG_TTYS0_BASE+0x00)
/* Control */
#define TTYS0_TBR TTYS0_RBR
-#define TTYS0_IER (TTYS0_BASE+0x01)
-#define TTYS0_IIR (TTYS0_BASE+0x02)
+#define TTYS0_IER (CONFIG_TTYS0_BASE+0x01)
+#define TTYS0_IIR (CONFIG_TTYS0_BASE+0x02)
#define TTYS0_FCR TTYS0_IIR
-#define TTYS0_LCR (TTYS0_BASE+0x03)
-#define TTYS0_MCR (TTYS0_BASE+0x04)
+#define TTYS0_LCR (CONFIG_TTYS0_BASE+0x03)
+#define TTYS0_MCR (CONFIG_TTYS0_BASE+0x04)
#define TTYS0_DLL TTYS0_RBR
#define TTYS0_DLM TTYS0_IER
/* Status */
-#define TTYS0_LSR (TTYS0_BASE+0x05)
-#define TTYS0_MSR (TTYS0_BASE+0x06)
-#define TTYS0_SCR (TTYS0_BASE+0x07)
+#define TTYS0_LSR (CONFIG_TTYS0_BASE+0x05)
+#define TTYS0_MSR (CONFIG_TTYS0_BASE+0x06)
+#define TTYS0_SCR (CONFIG_TTYS0_BASE+0x07)
mov %al, %ah
10: mov $TTYS0_LSR, %dx
{
/* they want a jump ... */
-#ifndef USE_DCACHE_RAM
+#ifndef CONFIG_USE_DCACHE_RAM
__asm__ __volatile__("jmp .+2\ninvd\njmp .+2\n");
#endif
StartTimer1();
*/
//VSA is cat onto the end after LB builds
- rom = ((unsigned long)0) - (ROM_SIZE + 36 * 1024);
+ rom = ((unsigned long)0) - (CONFIG_ROM_SIZE + 36 * 1024);
buf = (unsigned char *)VSA2_BUFFER;
olen = unrv2b((uint8_t *) rom, buf, &ilen);
printk_debug("buf ilen %d olen%d\n", ilen, olen);
msr.lo = (((CONFIG_LB_MEM_TOPK << 10) + TOP_MEM_MASK) & ~TOP_MEM_MASK);
wrmsr(TOP_MEM, msr);
-#if defined(XIP_ROM_SIZE)
+#if defined(CONFIG_XIP_ROM_SIZE)
/* enable write through caching so we can do execute in place
* on the flash rom.
*/
- set_var_mtrr(1, XIP_ROM_BASE, XIP_ROM_SIZE, MTRR_TYPE_WRBACK);
+ set_var_mtrr(1, CONFIG_XIP_ROM_BASE, CONFIG_XIP_ROM_SIZE, MTRR_TYPE_WRBACK);
#endif
/* Set the default memory type and enable fixed and variable MTRRs
/* FIXME we should probably query the cpu for this
* but so far this is all any recent AMD cpu has supported.
*/
- address_bits = CPU_ADDR_BITS; //K8 could be 40, and GH could be 48
+ address_bits = CONFIG_CPU_ADDR_BITS; //K8 could be 40, and GH could be 48
/* Now that I have mapped what is memory and what is not
* Setup the mtrrs so we can cache the memory.
if((apicid_base+ioapic_num-1)>0xf) {
// We need to enable APIC EXT ID
- printk_spew("if the IO APIC device doesn't support 256 apic id, \r\n you need to set ENABLE_APIC_EXT_ID in MB Option.lb so you can spare 16 id for ioapic\r\n");
+ printk_spew("if the IO APIC device doesn't support 256 apic id, \r\n you need to set CONFIG_ENABLE_APIC_EXT_ID in MB Option.lb so you can spare 16 id for ioapic\r\n");
enable_apic_ext_id(sysconf.nodes);
}
-uses K8_REV_F_SUPPORT
-uses K8_HT_FREQ_1G_SUPPORT
-uses DIMM_SUPPORT
-uses CPU_SOCKET_TYPE
+uses CONFIG_K8_REV_F_SUPPORT
+uses CONFIG_K8_HT_FREQ_1G_SUPPORT
+uses CONFIG_DIMM_SUPPORT
+uses CONFIG_CPU_SOCKET_TYPE
config chip.h
-default K8_REV_F_SUPPORT=1
+default CONFIG_K8_REV_F_SUPPORT=1
#Opteron K8 1G HT Support
-default K8_HT_FREQ_1G_SUPPORT=1
-default DIMM_SUPPORT=0x0004 #DDR2 unbuffered
-default CPU_SOCKET_TYPE=0x11
+default CONFIG_K8_HT_FREQ_1G_SUPPORT=1
+default CONFIG_DIMM_SUPPORT=0x0004 #DDR2 unbuffered
+default CONFIG_CPU_SOCKET_TYPE=0x11
object socket_AM2.o
-uses K8_REV_F_SUPPORT
-uses K8_HT_FREQ_1G_SUPPORT
-uses DIMM_SUPPORT
-uses CPU_SOCKET_TYPE
+uses CONFIG_K8_REV_F_SUPPORT
+uses CONFIG_K8_HT_FREQ_1G_SUPPORT
+uses CONFIG_DIMM_SUPPORT
+uses CONFIG_CPU_SOCKET_TYPE
config chip.h
-default K8_REV_F_SUPPORT=1
+default CONFIG_K8_REV_F_SUPPORT=1
#Opteron K8 1G HT Support
-default K8_HT_FREQ_1G_SUPPORT=1
-default DIMM_SUPPORT=0x0104 #DDR2 and REG
-default CPU_SOCKET_TYPE=0x10
+default CONFIG_K8_HT_FREQ_1G_SUPPORT=1
+default CONFIG_DIMM_SUPPORT=0x0104 #DDR2 and REG
+default CONFIG_CPU_SOCKET_TYPE=0x10
object socket_F.o
# Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
#
-uses PCI_IO_CFG_EXT
-uses MMCONF_SUPPORT
-uses HT3_SUPPORT
-uses EXT_RT_TBL_SUPPORT
-uses EXT_CONF_SUPPORT
-uses DIMM_SUPPORT
-uses CPU_SOCKET_TYPE
-uses CBB
-uses CDB
-uses PCI_BUS_SEGN_BITS
-uses CAR_FAM10
+uses CONFIG_PCI_IO_CFG_EXT
+uses CONFIG_MMCONF_SUPPORT
+uses CONFIG_HT3_SUPPORT
+uses CONFIG_EXT_RT_TBL_SUPPORT
+uses CONFIG_EXT_CONF_SUPPORT
+uses CONFIG_DIMM_SUPPORT
+uses CONFIG_CPU_SOCKET_TYPE
+uses CONFIG_CBB
+uses CONFIG_CDB
+uses CONFIG_PCI_BUS_SEGN_BITS
+uses CONFIG_CAR_FAM10
config chip.h
-default PCI_IO_CFG_EXT=1
+default CONFIG_PCI_IO_CFG_EXT=1
-default HT3_SUPPORT=1
-default EXT_RT_TBL_SUPPORT=0
-default EXT_CONF_SUPPORT=0
-default DIMM_SUPPORT=0x0104 #DDR2 and REG
-default CPU_SOCKET_TYPE=0x10
+default CONFIG_HT3_SUPPORT=1
+default CONFIG_EXT_RT_TBL_SUPPORT=0
+default CONFIG_EXT_CONF_SUPPORT=0
+default CONFIG_DIMM_SUPPORT=0x0104 #DDR2 and REG
+default CONFIG_CPU_SOCKET_TYPE=0x10
-default CAR_FAM10=1
+default CONFIG_CAR_FAM10=1
-if EXT_RT_TBL_SUPPORT
- default CBB=0xff
- default CDB=0
+if CONFIG_EXT_RT_TBL_SUPPORT
+ default CONFIG_CBB=0xff
+ default CONFIG_CDB=0
end
-#default MMCONF_SUPPORT=1
-#default MMCONF_SUPPORT_DEFAULT=1
+#default CONFIG_MMCONF_SUPPORT=1
+#default CONFIG_MMCONF_SUPPORT_DEFAULT=1
object socket_F_1207.o
-uses K8_REV_F_SUPPORT
-uses K8_HT_FREQ_1G_SUPPORT
-uses DIMM_SUPPORT
-uses CPU_SOCKET_TYPE
+uses CONFIG_K8_REV_F_SUPPORT
+uses CONFIG_K8_HT_FREQ_1G_SUPPORT
+uses CONFIG_DIMM_SUPPORT
+uses CONFIG_CPU_SOCKET_TYPE
config chip.h
-default K8_REV_F_SUPPORT=1
+default CONFIG_K8_REV_F_SUPPORT=1
#Opteron K8 1G HT Support
-default K8_HT_FREQ_1G_SUPPORT=1
-default DIMM_SUPPORT=0x0204 #DDR2 and REG, S1G1
-default CPU_SOCKET_TYPE=0x12
+default CONFIG_K8_HT_FREQ_1G_SUPPORT=1
+default CONFIG_DIMM_SUPPORT=0x0204 #DDR2 and REG, S1G1
+default CONFIG_CPU_SOCKET_TYPE=0x12
object socket_S1G1.o
return tolm;
}
-#if HAVE_HIGH_TABLES==1
+#if CONFIG_HAVE_HIGH_TABLES==1
#define HIGH_TABLES_SIZE 64 // maximum size of high tables in KB
extern uint64_t high_tables_base, high_tables_size;
#endif
ram_resource(dev, idx++, 0, 640);
ram_resource(dev, idx++, 768, tolmk - 768);
-#if HAVE_HIGH_TABLES==1
+#if CONFIG_HAVE_HIGH_TABLES==1
/* Leave some space for ACPI, PIRQ and MP tables */
high_tables_base = (tomk - HIGH_TABLES_SIZE) * 1024;
high_tables_size = HIGH_TABLES_SIZE * 1024;
-uses HAVE_MOVNTI
-default HAVE_MOVNTI=1
+uses CONFIG_HAVE_MOVNTI
+default CONFIG_HAVE_MOVNTI=1
dir /cpu/x86/tsc
dir /cpu/x86/mtrr
* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*/
-#define CACHE_AS_RAM_SIZE DCACHE_RAM_SIZE
-#define CACHE_AS_RAM_BASE DCACHE_RAM_BASE
+#define CACHE_AS_RAM_SIZE CONFIG_DCACHE_RAM_SIZE
+#define CACHE_AS_RAM_BASE CONFIG_DCACHE_RAM_BASE
#define post_code(x) intel_chip_post_macro(x)
#include <cpu/x86/mtrr.h>
movl %eax, %ebp
cache_as_ram:
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
post_code(0x20)
orl $(1 << 30), %eax
movl %eax, %cr0
-#if defined(XIP_ROM_SIZE) && defined(XIP_ROM_BASE)
+#if defined(CONFIG_XIP_ROM_SIZE) && defined(CONFIG_XIP_ROM_BASE)
/* Enable cache for our code in Flash because we do XIP here */
movl $MTRRphysBase_MSR(1), %ecx
xorl %edx, %edx
- movl $(XIP_ROM_BASE | MTRR_TYPE_WRBACK), %eax
+ movl $(CONFIG_XIP_ROM_BASE | MTRR_TYPE_WRBACK), %eax
wrmsr
movl $MTRRphysMask_MSR(1), %ecx
movl $0x0000000f, %edx
- movl $(~(XIP_ROM_SIZE - 1) | 0x800), %eax
+ movl $(~(CONFIG_XIP_ROM_SIZE - 1) | 0x800), %eax
wrmsr
-#endif /* XIP_ROM_SIZE && XIP_ROM_BASE */
+#endif /* CONFIG_XIP_ROM_SIZE && CONFIG_XIP_ROM_BASE */
/* enable cache */
movl %cr0, %eax
{
unsigned int cpu_reset = 0;
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
/* Is this a deliberate reset by the bios */
if (bios_reset_detected() && last_boot_normal()) {
goto normal_image;
}
__asm__ volatile (
- /* set new esp */ /* before _RAMBASE */
+ /* set new esp */ /* before CONFIG_RAMBASE */
"subl %0, %%ebp\n\t"
"subl %0, %%esp\n\t"
- ::"a"( (DCACHE_RAM_BASE + DCACHE_RAM_SIZE)- _RAMBASE )
+ ::"a"( (CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE)- CONFIG_RAMBASE )
);
{
-uses HAVE_MOVNTI
-default HAVE_MOVNTI=1
+uses CONFIG_HAVE_MOVNTI
+default CONFIG_HAVE_MOVNTI=1
dir /cpu/x86/tsc
dir /cpu/x86/mtrr
* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*/
-#define CACHE_AS_RAM_SIZE DCACHE_RAM_SIZE
-#define CACHE_AS_RAM_BASE DCACHE_RAM_BASE
+#define CACHE_AS_RAM_SIZE CONFIG_DCACHE_RAM_SIZE
+#define CACHE_AS_RAM_BASE CONFIG_DCACHE_RAM_BASE
#define post_code(x) intel_chip_post_macro(x)
#include <cpu/x86/mtrr.h>
movl %eax, %ebp
cache_as_ram:
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
post_code(0x20)
orl $(1 << 30), %eax
movl %eax, %cr0
-#if defined(XIP_ROM_SIZE) && defined(XIP_ROM_BASE)
+#if defined(CONFIG_XIP_ROM_SIZE) && defined(CONFIG_XIP_ROM_BASE)
/* Enable cache for our code in Flash because we do XIP here */
movl $MTRRphysBase_MSR(1), %ecx
xorl %edx, %edx
- movl $(XIP_ROM_BASE | MTRR_TYPE_WRBACK), %eax
+ movl $(CONFIG_XIP_ROM_BASE | MTRR_TYPE_WRBACK), %eax
wrmsr
movl $MTRRphysMask_MSR(1), %ecx
movl $0x0000000f, %edx
- movl $(~(XIP_ROM_SIZE - 1) | 0x800), %eax
+ movl $(~(CONFIG_XIP_ROM_SIZE - 1) | 0x800), %eax
wrmsr
-#endif /* XIP_ROM_SIZE && XIP_ROM_BASE */
+#endif /* CONFIG_XIP_ROM_SIZE && CONFIG_XIP_ROM_BASE */
/* enable cache */
movl %cr0, %eax
{
unsigned int cpu_reset = 0;
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
/* Is this a deliberate reset by the bios */
if (bios_reset_detected() && last_boot_normal()) {
goto normal_image;
}
__asm__ volatile (
- /* set new esp */ /* before _RAMBASE */
+ /* set new esp */ /* before CONFIG_RAMBASE */
"subl %0, %%ebp\n\t"
"subl %0, %%esp\n\t"
- ::"a"( (DCACHE_RAM_BASE + DCACHE_RAM_SIZE)- _RAMBASE )
+ ::"a"( (CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE)- CONFIG_RAMBASE )
);
{
-uses HAVE_MOVNTI
-default HAVE_MOVNTI=1
+uses CONFIG_HAVE_MOVNTI
+default CONFIG_HAVE_MOVNTI=1
dir /cpu/x86/tsc
dir /cpu/x86/mtrr
dir /cpu/x86/fpu
-uses HAVE_MOVNTI
-default HAVE_MOVNTI=1
+uses CONFIG_HAVE_MOVNTI
+default CONFIG_HAVE_MOVNTI=1
dir /cpu/x86/tsc
dir /cpu/x86/mtrr
dir /cpu/x86/fpu
-uses HAVE_MOVNTI
-default HAVE_MOVNTI=1
+uses CONFIG_HAVE_MOVNTI
+default CONFIG_HAVE_MOVNTI=1
dir /cpu/x86/tsc
dir /cpu/x86/mtrr
dir /cpu/x86/fpu
-uses HAVE_MOVNTI
-default HAVE_MOVNTI=1
+uses CONFIG_HAVE_MOVNTI
+default CONFIG_HAVE_MOVNTI=1
dir /cpu/x86/tsc
dir /cpu/x86/mtrr
dir /cpu/x86/fpu
-uses HAVE_MOVNTI
-default HAVE_MOVNTI=1
+uses CONFIG_HAVE_MOVNTI
+default CONFIG_HAVE_MOVNTI=1
dir /cpu/x86/tsc
dir /cpu/x86/mtrr
dir /cpu/x86/fpu
##
## CPU initialization
##
-uses _RAMBASE
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
+uses CONFIG_RAMBASE
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
##
## Use cache ram for initial setup
##
-default USE_DCACHE_RAM=1
+default CONFIG_USE_DCACHE_RAM=1
## Set dcache ram above coreboot image
-default DCACHE_RAM_BASE=_RAMBASE+0x100000
+default CONFIG_DCACHE_RAM_BASE=CONFIG_RAMBASE+0x100000
## Dcache size is 32Kb
-default DCACHE_RAM_SIZE=0x8000
+default CONFIG_DCACHE_RAM_SIZE=0x8000
initinclude "FAMILY_INIT" cpu/ppc/mpc74xx/mpc74xx.inc
object cache.S
* - enable L1 I/D caches, otherwise performance will be slow
* - set up DBATs for the following regions:
* - RAM (generally 0x00000000 -> 0x7fffffff)
- * - ROM (_ROMBASE -> _ROMBASE + ROM_SIZE)
+ * - ROM (CONFIG_ROMBASE -> CONFIG_ROMBASE + CONFIG_ROM_SIZE)
* - I/O (generally 0xfc000000 -> 0xfdffffff)
* - the main purpose for setting up the DBATs is so the I/O region
* can be marked cache inhibited/write through
* IBATS
*
* IBAT0 covers RAM (0 -> 256Mb)
- * IBAT1 covers ROM (_ROMBASE -> _ROMBASE+ROM_SIZE)
+ * IBAT1 covers ROM (CONFIG_ROMBASE -> CONFIG_ROMBASE+CONFIG_ROM_SIZE)
*/
lis r2, 0@h
ori r3, r2, BAT_BL_256M | BAT_VALID_SUPERVISOR | BAT_VALID_USER
mtibatl 0, r2
isync
- lis r2, _ROMBASE@h
-#if ROM_SIZE > 1048576
+ lis r2, CONFIG_ROMBASE@h
+#if CONFIG_ROM_SIZE > 1048576
ori r3, r2, BAT_BL_16M | BAT_VALID_SUPERVISOR | BAT_VALID_USER
#else
ori r3, r2, BAT_BL_1M | BAT_VALID_SUPERVISOR | BAT_VALID_USER
##
## CPU initialization
##
-uses _RAMBASE
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
+uses CONFIG_RAMBASE
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
##
## PPC4XX always uses cache ram for initial setup
##
-default USE_DCACHE_RAM=1
+default CONFIG_USE_DCACHE_RAM=1
## Set dcache ram above coreboot image
-default DCACHE_RAM_BASE=_RAMBASE+0x100000
+default CONFIG_DCACHE_RAM_BASE=CONFIG_RAMBASE+0x100000
## Dcache size is 16Kb
-default DCACHE_RAM_SIZE=16384
+default CONFIG_DCACHE_RAM_SIZE=16384
initinclude "FAMILY_INIT" cpu/ppc/ppc4xx/ppc4xx.inc
initobject cache.S
invalidate_dcache:
li r6,0x0000 /* clear GPR 6 */
/* Do loop for # of dcache congruence classes. */
- li r7,(DCACHE_RAM_SIZE / CACHELINE_SIZE / 2)
+ li r7,(CONFIG_DCACHE_RAM_SIZE / CACHELINE_SIZE / 2)
/* NOTE: dccci invalidates both */
mtctr r7 /* ways in the D cache */
1:
mtdccr r10
/* do loop for # of congruence classes. */
- li r10,(DCACHE_RAM_SIZE / CACHELINE_SIZE / 2)
- li r11,(DCACHE_RAM_SIZE / 2) /* D cache set size - 2 way sets */
+ li r10,(CONFIG_DCACHE_RAM_SIZE / CACHELINE_SIZE / 2)
+ li r11,(CONFIG_DCACHE_RAM_SIZE / 2) /* D cache set size - 2 way sets */
mtctr r10
li r10,(0xE000-0x10000) /* start at 0xFFFFE000 */
add r11,r10,r11 /* add to get to other side of cache line */
{
int idx = 3; /* who knows? */
- ram_resource(dev, idx, 0, EMBEDDED_RAM_SIZE>>10);
+ ram_resource(dev, idx, 0, CONFIG_EMBEDDED_RAM_SIZE>>10);
assign_resources(&dev->link[0]);
}
isync
/*
- * Enable dcache region containing DCACHE_RAM_BASE
+ * Enable dcache region containing CONFIG_DCACHE_RAM_BASE
* On reset all regions are set to write-back, so we
* just leave them alone.
*
- * dccr = (1 << (0x1F - (DCACHE_RAM_BASE >> 27))
+ * dccr = (1 << (0x1F - (CONFIG_DCACHE_RAM_BASE >> 27))
*/
- lis r4, DCACHE_RAM_BASE@ha
- ori r4, r4, DCACHE_RAM_BASE@l
+ lis r4, CONFIG_DCACHE_RAM_BASE@ha
+ ori r4, r4, CONFIG_DCACHE_RAM_BASE@l
srwi r4, r4, 27
subfic r4, r4, 31
li r0, 1
/* TODO: work out why this trashes cache ram */
//mtsdram0(mem_mcopt1, 0x00000000);
-#if EMBEDDED_RAM_SIZE==128*1024*1024
+#if CONFIG_EMBEDDED_RAM_SIZE==128*1024*1024
/* TODO */
-#elif EMBEDDED_RAM_SIZE==64*1024*1024
+#elif CONFIG_EMBEDDED_RAM_SIZE==64*1024*1024
set_sdram0(mem_sdtr1, TR);
set_sdram0(mem_mb0cf, B0CR);
set_sdram0(mem_rtr, RTR);
set_sdram0(mem_ecccf, ECCCF);
set_sdram0(mem_pmit, PMIT);
-#elif EMBEDDED_RAM_SIZE==32*1024*1024
+#elif CONFIG_EMBEDDED_RAM_SIZE==32*1024*1024
/* TODO */
-#elif EMBEDDED_RAM_SIZE==16*1024*1024
+#elif CONFIG_EMBEDDED_RAM_SIZE==16*1024*1024
/* TODO */
#endif
##
## CPU initialization
##
-uses _RAMBASE
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
+uses CONFIG_RAMBASE
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
##
## PPC7XX always uses cache ram for initial setup
##
-default USE_DCACHE_RAM=1
+default CONFIG_USE_DCACHE_RAM=1
## Set dcache ram above coreboot image
-default DCACHE_RAM_BASE=_RAMBASE+0x100000
+default CONFIG_DCACHE_RAM_BASE=CONFIG_RAMBASE+0x100000
## Dcache size is 16Kb
-default DCACHE_RAM_SIZE=16384
+default CONFIG_DCACHE_RAM_SIZE=16384
initinclude "FAMILY_INIT" cpu/ppc/ppc7xx/ppc7xx.inc
* - enable L1 I/D caches, otherwise performance will be slow
* - set up DBATs for the following regions:
* - RAM (generally 0x00000000 -> 0x7fffffff)
- * - ROM (_ROMBASE -> _ROMBASE + ROM_SIZE)
+ * - ROM (CONFIG_ROMBASE -> CONFIG_ROMBASE + CONFIG_ROM_SIZE)
* - I/O (generally 0xfc000000 -> 0xfdffffff)
* - the main purpose for setting up the DBATs is so the I/O region
* can be marked cache inhibited/write through
* IBATS
*
* IBAT0 covers RAM (0 -> 256Mb)
- * IBAT1 covers ROM (_ROMBASE -> _ROMBASE+ROM_SIZE)
+ * IBAT1 covers ROM (CONFIG_ROMBASE -> CONFIG_ROMBASE+CONFIG_ROM_SIZE)
*/
lis r2, 0@h
ori r3, r2, BAT_BL_256M | BAT_VALID_SUPERVISOR | BAT_VALID_USER
mtibatl 0, r2
isync
- lis r2, _ROMBASE@h
-#if ROM_SIZE > 1048576
+ lis r2, CONFIG_ROMBASE@h
+#if CONFIG_ROM_SIZE > 1048576
ori r3, r2, BAT_BL_16M | BAT_VALID_SUPERVISOR | BAT_VALID_USER
#else
ori r3, r2, BAT_BL_1M | BAT_VALID_SUPERVISOR | BAT_VALID_USER
* Initialize data cache blocks
* (assumes cache block size of 32 bytes)
*/
- lis r1, DCACHE_RAM_BASE@h
- ori r1, r1, DCACHE_RAM_BASE@l
- li r3, (DCACHE_RAM_SIZE / 32)
+ lis r1, CONFIG_DCACHE_RAM_BASE@h
+ ori r1, r1, CONFIG_DCACHE_RAM_BASE@l
+ li r3, (CONFIG_DCACHE_RAM_SIZE / 32)
mtctr r3
0: dcbz r0, r1
addi r1, r1, 32
##
## CPU initialization
##
-uses _RAMBASE
-uses USE_DCACHE_RAM
+uses CONFIG_RAMBASE
+uses CONFIG_USE_DCACHE_RAM
##
## Assumes RAM already initialiazed
## This is true for the Apache board, but may
## not be for other 970 systems.
##
-default USE_DCACHE_RAM=0
+default CONFIG_USE_DCACHE_RAM=0
initinclude "FAMILY_INIT" cpu/ppc/ppc970/ppc970.inc
* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*/
-#define CacheSize DCACHE_RAM_SIZE
-#define CacheBase DCACHE_RAM_BASE
+#define CacheSize CONFIG_DCACHE_RAM_SIZE
+#define CacheBase CONFIG_DCACHE_RAM_BASE
#include <cpu/x86/mtrr.h>
/* MTRRPhysBase */
movl $0x202, %ecx
xorl %edx, %edx
- movl $(XIP_ROM_BASE|MTRR_TYPE_WRBACK),%eax
+ movl $(CONFIG_XIP_ROM_BASE|MTRR_TYPE_WRBACK),%eax
wrmsr
/* MTRRPhysMask */
movl $0x203, %ecx
movl $0x0000000f,%edx
- movl $(~(XIP_ROM_SIZE - 1) | 0x800), %eax
+ movl $(~(CONFIG_XIP_ROM_SIZE - 1) | 0x800), %eax
wrmsr
xorl $0x5c5c5c5c,%eax
rep stosl
- movl XIP_ROM_BASE, %esi
+ movl CONFIG_XIP_ROM_BASE, %esi
movl %esi, %edi
- movl $(XIP_ROM_SIZE>>2), %ecx
+ movl $(CONFIG_XIP_ROM_SIZE>>2), %ecx
rep lodsl
/* The key point of this CAR code is C7 cache does not turn into
"movl $((~(( 0 + 0x40000) - 1)) | 0x800), %eax\n\t"
"wrmsr\n\t"
- /*jasonzhao@viatech.com.cn add this 2008-11-27, cache XIP_ROM_BASE-SIZE to speedup the coreboot code*/
+ /*jasonzhao@viatech.com.cn add this 2008-11-27, cache CONFIG_XIP_ROM_BASE-SIZE to speedup the coreboot code*/
"movl $0x206, %ecx\n\t"
"xorl %edx, %edx\n\t"
- "movl $XIP_ROM_BASE,%eax\n\t"
+ "movl $CONFIG_XIP_ROM_BASE,%eax\n\t"
"orl $(0 | 6), %eax\n\t"
"wrmsr\n\t"
"movl $0x207, %ecx\n\t"
"xorl %edx, %edx\n\t"
- "movl $XIP_ROM_SIZE,%eax\n\t"
+ "movl $CONFIG_XIP_ROM_SIZE,%eax\n\t"
"decl %eax\n\t"
"notl %eax\n\t"
"orl $(0 | 0x800), %eax\n\t"
SECTIONS {
/* Trigger an error if I have an unuseable start address */
- _bogus = ASSERT(_start >= 0xffff0000, "_start too low. Please decrease ROM_IMAGE_SIZE");
+ _bogus = ASSERT(_start >= 0xffff0000, "_start too low. Please decrease CONFIG_ROM_IMAGE_SIZE");
_ROMTOP = 0xfffffff0;
. = _ROMTOP;
.reset . : {
*/
SECTIONS {
- _ROMTOP = _ROMBASE + ROM_IMAGE_SIZE - 0x10;
+ _ROMTOP = CONFIG_ROMBASE + CONFIG_ROM_IMAGE_SIZE - 0x10;
. = _ROMTOP;
.reset (.): {
*(.reset)
/* disable HyperThreading is done by eswar*/
/* other's is the same as AMD except remove amd specific msr */
-#define CacheSize DCACHE_RAM_SIZE
+#define CacheSize CONFIG_DCACHE_RAM_SIZE
#define CacheBase (0xd0000 - CacheSize)
#include <cpu/x86/mtrr.h>
CacheAsRam:
/* hope we can skip the double set for normal part */
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
// Check whether the processor has HT capability
movl $01, %eax
orl $(0x1<<30),%eax
movl %eax, %cr0
-#endif /* USE_FALLBACK_IMAGE == 1*/
+#endif /* CONFIG_USE_FALLBACK_IMAGE == 1*/
-#if defined(XIP_ROM_SIZE) && defined(XIP_ROM_BASE)
+#if defined(CONFIG_XIP_ROM_SIZE) && defined(CONFIG_XIP_ROM_BASE)
/* enable write base caching so we can do execute in place
* on the flash rom.
*/
movl $0x202, %ecx
xorl %edx, %edx
- movl $(XIP_ROM_BASE | MTRR_TYPE_WRBACK), %eax
+ movl $(CONFIG_XIP_ROM_BASE | MTRR_TYPE_WRBACK), %eax
wrmsr
movl $0x203, %ecx
movl $0x0000000f, %edx
- movl $(~(XIP_ROM_SIZE - 1) | 0x800), %eax
+ movl $(~(CONFIG_XIP_ROM_SIZE - 1) | 0x800), %eax
wrmsr
-#endif /* XIP_ROM_SIZE && XIP_ROM_BASE */
+#endif /* CONFIG_XIP_ROM_SIZE && CONFIG_XIP_ROM_BASE */
/* enable cache */
movl %cr0, %eax
andl $0x9fffffff,%eax
movl %eax, %cr0
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
/* Read the range with lodsl*/
movl $CacheBase, %esi
.xout1x:
#endif
-#endif /*USE_FALLBACK_IMAGE == 1*/
+#endif /*CONFIG_USE_FALLBACK_IMAGE == 1*/
movl $(CacheBase+CacheSize-4), %eax
.long 0x20C, 0x20D, 0x20E, 0x20F
.long 0x000 /* NULL, end of table */
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
.align 0x1000
.code16
.global LogicalAP_SIPI
hlt
jmp Halt_LogicalAP
.code32
-#endif /*USE_FALLBACK_IMAGE == 1*/
+#endif /*CONFIG_USE_FALLBACK_IMAGE == 1*/
.CacheAsRam_out:
"xorl %edx, %edx\n\t"
"xorl %eax, %eax\n\t"
"wrmsr\n\t"
-#if DCACHE_RAM_SIZE > 0x8000
+#if CONFIG_DCACHE_RAM_SIZE > 0x8000
"movl $0x268, %ecx\n\t" /* fix4k_c0000*/
"wrmsr\n\t"
#endif
if (cpu_reset == 1) cpu_reset = -1;
else cpu_reset = 0;
-# if USE_FALLBACK_IMAGE == 1
+# if CONFIG_USE_FALLBACK_IMAGE == 1
cbfs_and_run_core("fallback/coreboot_ram", cpu_reset);
# else
cbfs_and_run_core("normal/coreboot_ram", cpu_reset);
/*
2005.12 yhlu add coreboot_ram cross the vga font buffer handling
- 2005.12 yhlu add _RAMBASE above 1M support for SMP
+ 2005.12 yhlu add CONFIG_RAMBASE above 1M support for SMP
2008.05 stepan add support for going back to sipi wait state
*/
#if CONFIG_SMP == 1
-#if _RAMBASE >= 0x100000
+#if CONFIG_RAMBASE >= 0x100000
/* This is a lot more paranoid now, since Linux can NOT handle
* being told there is a CPU when none exists. So any errors
* will return 0, meaning no CPU.
}
#endif
-#if HAVE_ACPI_RESUME == 1
+#if CONFIG_HAVE_ACPI_RESUME == 1
char *lowmem_backup;
char *lowmem_backup_ptr;
int lowmem_backup_size;
static void copy_secondary_start_to_1m_below(void)
{
-#if _RAMBASE >= 0x100000
+#if CONFIG_RAMBASE >= 0x100000
extern char _secondary_start[];
extern char _secondary_start_end[];
unsigned long code_size;
start_eip = get_valid_start_eip((unsigned long)_secondary_start);
code_size = (unsigned long)_secondary_start_end - (unsigned long)_secondary_start;
-#if HAVE_ACPI_RESUME == 1
+#if CONFIG_HAVE_ACPI_RESUME == 1
/* need to save it for RAM resume */
lowmem_backup_size = code_size;
lowmem_backup = malloc(code_size);
return 0;
}
-#if _RAMBASE >= 0x100000
+#if CONFIG_RAMBASE >= 0x100000
start_eip = get_valid_start_eip((unsigned long)_secondary_start);
#else
start_eip = (unsigned long)_secondary_start;
index = ++last_cpu_index;
/* Find end of the new processors stack */
-#if (CONFIG_LB_MEM_TOPK>1024) && (_RAMBASE < 0x100000) && ((CONFIG_CONSOLE_VGA==1) || (CONFIG_PCI_ROM_RUN == 1))
+#if (CONFIG_LB_MEM_TOPK>1024) && (CONFIG_RAMBASE < 0x100000) && ((CONFIG_CONSOLE_VGA==1) || (CONFIG_PCI_ROM_RUN == 1))
if(index<1) { // only keep bsp on low
- stack_end = ((unsigned long)_estack) - (STACK_SIZE*index) - sizeof(struct cpu_info);
+ stack_end = ((unsigned long)_estack) - (CONFIG_STACK_SIZE*index) - sizeof(struct cpu_info);
} else {
// for all APs, let use stack after pgtbl, 20480 is the pgtbl size for every cpu
- stack_end = 0x100000+(20480 + STACK_SIZE)*CONFIG_MAX_CPUS - (STACK_SIZE*index);
-#if (0x100000+(20480 + STACK_SIZE)*CONFIG_MAX_CPUS) > (CONFIG_LB_MEM_TOPK<<10)
- #warning "We may need to increase CONFIG_LB_MEM_TOPK, it need to be more than (0x100000+(20480 + STACK_SIZE)*CONFIG_MAX_CPUS)\n"
+ stack_end = 0x100000+(20480 + CONFIG_STACK_SIZE)*CONFIG_MAX_CPUS - (CONFIG_STACK_SIZE*index);
+#if (0x100000+(20480 + CONFIG_STACK_SIZE)*CONFIG_MAX_CPUS) > (CONFIG_LB_MEM_TOPK<<10)
+ #warning "We may need to increase CONFIG_LB_MEM_TOPK, it need to be more than (0x100000+(20480 + CONFIG_STACK_SIZE)*CONFIG_MAX_CPUS)\n"
#endif
if(stack_end > (CONFIG_LB_MEM_TOPK<<10)) {
printk_debug("start_cpu: Please increase the CONFIG_LB_MEM_TOPK more than %luK\n", stack_end>>10);
stack_end -= sizeof(struct cpu_info);
}
#else
- stack_end = ((unsigned long)_estack) - (STACK_SIZE*index) - sizeof(struct cpu_info);
+ stack_end = ((unsigned long)_estack) - (CONFIG_STACK_SIZE*index) - sizeof(struct cpu_info);
#endif
void secondary_cpu_init(void)
{
atomic_inc(&active_cpus);
-#if SERIAL_CPU_INIT == 1
+#if CONFIG_SERIAL_CPU_INIT == 1
#if CONFIG_MAX_CPUS>2
spin_lock(&start_cpu_lock);
#endif
#endif
cpu_initialize();
-#if SERIAL_CPU_INIT == 1
+#if CONFIG_SERIAL_CPU_INIT == 1
#if CONFIG_MAX_CPUS>2
spin_unlock(&start_cpu_lock);
#endif
if (cpu->path.type != DEVICE_PATH_APIC) {
continue;
}
- #if SERIAL_CPU_INIT == 0
+ #if CONFIG_SERIAL_CPU_INIT == 0
if(cpu==bsp_cpu) {
continue;
}
printk_err("CPU 0x%02x would not start!\n",
cpu->path.apic.apic_id);
}
-#if SERIAL_CPU_INIT == 1
+#if CONFIG_SERIAL_CPU_INIT == 1
#if CONFIG_MAX_CPUS>2
udelay(10);
#endif
#define initialize_other_cpus(root) do {} while(0)
#endif /* CONFIG_SMP */
-#if WAIT_BEFORE_CPUS_INIT==0
+#if CONFIG_WAIT_BEFORE_CPUS_INIT==0
#define cpus_ready_for_init() do {} while(0)
#else
void cpus_ready_for_init(void);
#endif
-#if HAVE_SMI_HANDLER
+#if CONFIG_HAVE_SMI_HANDLER
void smm_init(void);
#endif
copy_secondary_start_to_1m_below(); // why here? In case some day we can start core1 in amd_sibling_init
#endif
-#if HAVE_SMI_HANDLER
+#if CONFIG_HAVE_SMI_HANDLER
smm_init();
#endif
cpus_ready_for_init();
#if CONFIG_SMP == 1
- #if SERIAL_CPU_INIT == 0
+ #if CONFIG_SERIAL_CPU_INIT == 0
/* start all aps at first, so we can init ECC all together */
start_other_cpus(cpu_bus, info->cpu);
#endif
cpu_initialize();
#if CONFIG_SMP == 1
- #if SERIAL_CPU_INIT == 1
+ #if CONFIG_SERIAL_CPU_INIT == 1
start_other_cpus(cpu_bus, info->cpu);
#endif
#include <cpu/x86/mtrr.h>
#include <cpu/x86/msr.h>
-/* Validate XIP_ROM_SIZE and XIP_ROM_BASE */
-#if defined(XIP_ROM_SIZE) && !defined(XIP_ROM_BASE)
-# error "XIP_ROM_SIZE without XIP_ROM_BASE"
+/* Validate CONFIG_XIP_ROM_SIZE and CONFIG_XIP_ROM_BASE */
+#if defined(CONFIG_XIP_ROM_SIZE) && !defined(CONFIG_XIP_ROM_BASE)
+# error "CONFIG_XIP_ROM_SIZE without CONFIG_XIP_ROM_BASE"
#endif
-#if defined(XIP_ROM_BASE) && !defined(XIP_ROM_SIZE)
-# error "XIP_ROM_BASE without XIP_ROM_SIZE"
+#if defined(CONFIG_XIP_ROM_BASE) && !defined(CONFIG_XIP_ROM_SIZE)
+# error "CONFIG_XIP_ROM_BASE without CONFIG_XIP_ROM_SIZE"
#endif
#if !defined(CONFIG_LB_MEM_TOPK)
# error "CONFIG_LB_MEM_TOPK not defined"
#endif
-#if defined(XIP_ROM_SIZE) && ((XIP_ROM_SIZE & (XIP_ROM_SIZE -1)) != 0)
-# error "XIP_ROM_SIZE is not a power of 2"
+#if defined(CONFIG_XIP_ROM_SIZE) && ((CONFIG_XIP_ROM_SIZE & (CONFIG_XIP_ROM_SIZE -1)) != 0)
+# error "CONFIG_XIP_ROM_SIZE is not a power of 2"
#endif
-#if defined(XIP_ROM_SIZE) && ((XIP_ROM_BASE % XIP_ROM_SIZE) != 0)
-# error "XIP_ROM_BASE is not a multiple of XIP_ROM_SIZE"
+#if defined(CONFIG_XIP_ROM_SIZE) && ((CONFIG_XIP_ROM_BASE % CONFIG_XIP_ROM_SIZE) != 0)
+# error "CONFIG_XIP_ROM_BASE is not a multiple of CONFIG_XIP_ROM_SIZE"
#endif
#if (CONFIG_LB_MEM_TOPK & (CONFIG_LB_MEM_TOPK -1)) != 0
basem.hi = 0;
wrmsr(MTRRphysBase_MSR(reg), basem);
maskm.lo = ~(size - 1) | 0x800;
- maskm.hi = (1<<(CPU_ADDR_BITS-32))-1;
+ maskm.hi = (1<<(CONFIG_CPU_ADDR_BITS-32))-1;
wrmsr(MTRRphysMask_MSR(reg), maskm);
}
/* Bit Bit 32-35 of MTRRphysMask should be set to 1 */
msr_t basem, maskm;
basem.lo = (base_lo & 0xfffff000) | type;
- basem.hi = base_hi & ((1<<(CPU_ADDR_BITS-32))-1);
+ basem.hi = base_hi & ((1<<(CONFIG_CPU_ADDR_BITS-32))-1);
wrmsr(MTRRphysBase_MSR(reg), basem);
- maskm.hi = (1<<(CPU_ADDR_BITS-32))-1;
+ maskm.hi = (1<<(CONFIG_CPU_ADDR_BITS-32))-1;
if(size_lo) {
maskm.lo = ~(size_lo - 1) | 0x800;
} else {
wrmsr(msr_nr, msr);
}
-#if defined(XIP_ROM_SIZE)
+#if defined(CONFIG_XIP_ROM_SIZE)
/* enable write through caching so we can do execute in place
* on the flash rom.
*/
- set_var_mtrr(1, XIP_ROM_BASE, XIP_ROM_SIZE, MTRR_TYPE_WRBACK);
+ set_var_mtrr(1, CONFIG_XIP_ROM_BASE, CONFIG_XIP_ROM_SIZE, MTRR_TYPE_WRBACK);
#endif
/* Set the default memory type and enable fixed and variable MTRRs
struct pde pdp[512];
} __attribute__ ((packed));
-#if (CONFIG_LB_MEM_TOPK>1024) && (_RAMBASE<0x100000) && ((CONFIG_CONSOLE_VGA==1) || (CONFIG_PCI_ROM_RUN == 1))
+#if (CONFIG_LB_MEM_TOPK>1024) && (CONFIG_RAMBASE<0x100000) && ((CONFIG_CONSOLE_VGA==1) || (CONFIG_PCI_ROM_RUN == 1))
/*
pgtbl is too big, so use last one 1M before CONFIG_LB_MEM_TOP, otherwise for 8 way dual core with vga support will push stack and heap cross 0xa0000,
and that region need to be used as vga font buffer. Please make sure set CONFIG_LB_MEM_TOPK=2048 in MB Config
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_SMI_HANDLER
+uses CONFIG_HAVE_SMI_HANDLER
-if HAVE_SMI_HANDLER
+if CONFIG_HAVE_SMI_HANDLER
object smmrelocate.S
smmobject smmhandler.S
makerule smm
depends "smm.o $(TOP)/src/cpu/x86/smm/smm.ld ldoptions"
action "$(CC) $(DISTRO_LFLAGS) -nostdlib -nostartfiles -static -o smm.elf -T $(TOP)/src/cpu/x86/smm/smm.ld smm.o"
- action "$(CROSS_COMPILE)nm -n smm.elf | sort > smm.map"
- action "$(OBJCOPY) -O binary smm.elf smm"
+ action "$(CONFIG_CROSS_COMPILE)nm -n smm.elf | sort > smm.map"
+ action "$(CONFIG_OBJCOPY) -O binary smm.elf smm"
end
makerule smm_bin.c
static int uart_can_tx_byte(void)
{
- return inb(TTYS0_BASE + UART_LSR) & 0x20;
+ return inb(CONFIG_TTYS0_BASE + UART_LSR) & 0x20;
}
static void uart_wait_to_tx_byte(void)
static void uart_wait_until_sent(void)
{
- while(!(inb(TTYS0_BASE + UART_LSR) & 0x40))
+ while(!(inb(CONFIG_TTYS0_BASE + UART_LSR) & 0x40))
;
}
static void uart_tx_byte(unsigned char data)
{
uart_wait_to_tx_byte();
- outb(data, TTYS0_BASE + UART_TBR);
+ outb(data, CONFIG_TTYS0_BASE + UART_TBR);
/* Make certain the data clears the fifos */
uart_wait_until_sent();
}
node=nodeid();
#ifdef DEBUG_SMI
- console_loglevel = DEFAULT_CONSOLE_LOGLEVEL;
+ console_loglevel = CONFIG_DEFAULT_CONSOLE_LOGLEVEL;
#else
console_loglevel = 1;
#endif
/* End of hardware specific section. */
#ifdef DEBUG_SMM_RELOCATION
/* print [SMM-x] so we can determine if CPUx went to SMM */
- movw $TTYS0_BASE, %dx
+ movw $CONFIG_TTYS0_BASE, %dx
mov $'[', %al
outb %al, %dx
mov $'S', %al
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
-uses HAVE_INIT_TIMER
+uses CONFIG_HAVE_INIT_TIMER
default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2=0
if CONFIG_UDELAY_TSC
- default HAVE_INIT_TIMER=1
+ default CONFIG_HAVE_INIT_TIMER=1
object delay_tsc.o
end
memcpy(buffer, "Root Device", 12);
break;
case DEVICE_PATH_PCI:
-#if PCI_BUS_SEGN_BITS
+#if CONFIG_PCI_BUS_SEGN_BITS
sprintf(buffer, "PCI: %04x:%02x:%02x.%01x",
dev->bus->secondary>>8, dev->bus->secondary & 0xff,
PCI_SLOT(dev->path.pci.devfn), PCI_FUNC(dev->path.pci.devfn));
end = resource_end(resource);
buf[0] = '\0';
if (resource->flags & IORESOURCE_PCI_BRIDGE) {
-#if PCI_BUS_SEGN_BITS
+#if CONFIG_PCI_BUS_SEGN_BITS
sprintf(buf, "bus %04x:%02x ", dev->bus->secondary>>8, dev->link[0].secondary & 0xff);
#else
sprintf(buf, "bus %02x ", dev->link[0].secondary);
buf[0] = '\0';
/*
if (resource->flags & IORESOURCE_BRIDGE) {
-#if PCI_BUS_SEGN_BITS
+#if CONFIG_PCI_BUS_SEGN_BITS
sprintf(buf, "bus %04x:%02x ", dev->bus->secondary >> 8,
dev->link[0].secondary & 0xff);
#else
}
/* AMD K8 Unsupported 1Ghz? */
if ((dev->vendor == PCI_VENDOR_ID_AMD) && (dev->device == 0x1100)) {
-#if K8_HT_FREQ_1G_SUPPORT == 1
- #if K8_REV_F_SUPPORT == 0
+#if CONFIG_K8_HT_FREQ_1G_SUPPORT == 1
+ #if CONFIG_K8_REV_F_SUPPORT == 0
if (is_cpu_pre_e0()) { // only e0 later suupport 1GHz HT
freq_cap &= ~(1 << HT_FREQ_1000Mhz);
}
} while((ctrl & (1 << 5)) == 0);
//actually, only for one HT device HT chain, and unitid is 0
-#if HT_CHAIN_UNITID_BASE == 0
+#if CONFIG_HT_CHAIN_UNITID_BASE == 0
if(offset_unitid) {
return;
}
#endif
/* Check if is already collapsed */
- if((!offset_unitid)|| (offset_unitid && (!((HT_CHAIN_END_UNITID_BASE == 0) && (HT_CHAIN_END_UNITID_BASE <HT_CHAIN_UNITID_BASE))))) {
+ if((!offset_unitid)|| (offset_unitid && (!((CONFIG_HT_CHAIN_END_UNITID_BASE == 0) && (CONFIG_HT_CHAIN_END_UNITID_BASE <CONFIG_HT_CHAIN_UNITID_BASE))))) {
struct device dummy;
uint32_t id;
dummy.bus = bus;
unsigned int hypertransport_scan_chain(struct bus *bus,
unsigned min_devfn, unsigned max_devfn, unsigned int max, unsigned *ht_unitid_base, unsigned offset_unitid)
{
- //even HT_CHAIN_UNITID_BASE == 0, we still can go through this function, because of end_of_chain check, also We need it to optimize link
+ //even CONFIG_HT_CHAIN_UNITID_BASE == 0, we still can go through this function, because of end_of_chain check, also We need it to optimize link
unsigned next_unitid, last_unitid;
device_t old_devices, dev, func;
- unsigned min_unitid = (offset_unitid) ? HT_CHAIN_UNITID_BASE:1;
+ unsigned min_unitid = (offset_unitid) ? CONFIG_HT_CHAIN_UNITID_BASE:1;
struct ht_link prev;
device_t last_func = 0;
int ht_dev_num = 0;
unsigned max_unitid;
-#if HT_CHAIN_END_UNITID_BASE != 0x20
- //let't record the device of last ht device, So we can set the Unitid to HT_CHAIN_END_UNITID_BASE
+#if CONFIG_HT_CHAIN_END_UNITID_BASE != 0x20
+ //let't record the device of last ht device, So we can set the Unitid to CONFIG_HT_CHAIN_END_UNITID_BASE
unsigned real_last_unitid;
uint8_t real_last_pos;
device_t real_last_dev;
flags &= ~0x1f; /* mask out base Unit ID */
count = (flags >> 5) & 0x1f; /* get unit count */
-#if HT_CHAIN_END_UNITID_BASE != 0x20
+#if CONFIG_HT_CHAIN_END_UNITID_BASE != 0x20
if(offset_unitid) {
if(next_unitid > (max_devfn>>3)) { // max_devfn will be (0x17<<3)|7 or (0x1f<<3)|7
if(!end_used) {
- next_unitid = HT_CHAIN_END_UNITID_BASE;
+ next_unitid = CONFIG_HT_CHAIN_END_UNITID_BASE;
end_used = 1;
} else {
goto end_of_chain;
ht_unitid_base[ht_dev_num] = next_unitid;
ht_dev_num++;
-#if HT_CHAIN_END_UNITID_BASE != 0x20
+#if CONFIG_HT_CHAIN_END_UNITID_BASE != 0x20
if (offset_unitid) {
real_last_pos = pos;
real_last_unitid = next_unitid;
}
#endif
-#if HT_CHAIN_END_UNITID_BASE != 0x20
- if(offset_unitid && (ht_dev_num>1) && (real_last_unitid != HT_CHAIN_END_UNITID_BASE) && !end_used) {
+#if CONFIG_HT_CHAIN_END_UNITID_BASE != 0x20
+ if(offset_unitid && (ht_dev_num>1) && (real_last_unitid != CONFIG_HT_CHAIN_END_UNITID_BASE) && !end_used) {
uint16_t flags;
int i;
device_t last_func = 0;
flags = pci_read_config16(real_last_dev, real_last_pos + PCI_CAP_FLAGS);
flags &= ~0x1f;
- flags |= HT_CHAIN_END_UNITID_BASE & 0x1f;
+ flags |= CONFIG_HT_CHAIN_END_UNITID_BASE & 0x1f;
pci_write_config16(real_last_dev, real_last_pos + PCI_CAP_FLAGS, flags);
for(func = real_last_dev; func; func = func->sibling) {
- func->path.pci.devfn -= ((real_last_unitid - HT_CHAIN_END_UNITID_BASE) << 3);
+ func->path.pci.devfn -= ((real_last_unitid - CONFIG_HT_CHAIN_END_UNITID_BASE) << 3);
last_func = func;
}
- ht_unitid_base[ht_dev_num-1] = HT_CHAIN_END_UNITID_BASE; // update last one
+ ht_unitid_base[ht_dev_num-1] = CONFIG_HT_CHAIN_END_UNITID_BASE; // update last one
printk_debug(" unitid: %04x --> %04x\n",
- real_last_unitid, HT_CHAIN_END_UNITID_BASE);
+ real_last_unitid, CONFIG_HT_CHAIN_END_UNITID_BASE);
}
#endif
if (dev->on_mainboard && ops && ops->set_subsystem) {
printk_debug("%s subsystem <- %02x/%02x\n",
dev_path(dev),
- MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID,
- MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID);
+ CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID,
+ CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID);
ops->set_subsystem(dev,
- MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID,
- MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID);
+ CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID,
+ CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID);
}
command = pci_read_config16(dev, PCI_COMMAND);
command |= dev->command;
device_t old_devices;
device_t child;
-#if PCI_BUS_SEGN_BITS
+#if CONFIG_PCI_BUS_SEGN_BITS
printk_debug("PCI: pci_scan_bus for bus %04x:%02x\n", bus->secondary >> 8, bus->secondary & 0xff);
#else
printk_debug("PCI: pci_scan_bus for bus %02x\n", bus->secondary);
ops_pci_bus(pbus)->write32(pbus, dev->bus->secondary, dev->path.pci.devfn, where, val);
}
-#if MMCONF_SUPPORT
+#if CONFIG_MMCONF_SUPPORT
uint8_t pci_mmio_read_config8(device_t dev, unsigned where)
{
struct bus *pbus = get_pbus(dev);
switch(dev->path.pnp.device) {
case 0:
parent = dev->bus->dev;
- printk_debug("DEBUG: %s", dev_path(parent));
+ printk_debug("CONFIG_DEBUG: %s", dev_path(parent));
if(parent->chip_ops && parent->chip_ops->name) {
printk_debug(": %s\n", parent->chip_ops->name);
} else {
#define CFG1_THERM_HOT 0x10
#define CFT1_DAC_AFC 0x20
#define CFG1_PWM_AFC 0x40
-#define CFG1_RESET 0x80
+#define CFG1CONFIG_RESET 0x80
#define ADM1026_REG_CONFIG2 0x01
#define ADM1026_REG_CONFIG3 0x07
int result;
result = smbus_read_byte(dev, ADM1026_REG_CONFIG1);
- result = (result | CFG1_MONITOR) & ~(CFG1_INT_CLEAR | CFG1_RESET);
+ result = (result | CFG1_MONITOR) & ~(CFG1_INT_CLEAR | CFG1CONFIG_RESET);
result = smbus_write_byte(dev, ADM1026_REG_CONFIG1, result);
result = smbus_read_byte(dev, ADM1026_REG_CONFIG1);
* 2. Reduce the size of your normal (or fallback) image, by adding the
* following lines to your target Config.lb, after romimage "normal"
* # 48K for SCSI FW or ATI ROM
- * option ROM_SIZE = 512*1024-48*1024
+ * option CONFIG_ROM_SIZE = 512*1024-48*1024
* 3. Create your vgabios.bin, for example using awardeco and put it in the
* directory of your target Config.lb. You can also read an option rom from
* a running system, but this is unreliable, as some option roms are changed
// ROMCC doesn't support __FILE__ or __LINE__ :^{
-#if DEBUG
+#if CONFIG_DEBUG
#ifdef __ROMCC__
#define ASSERT(x) { if (!(x)) die("ASSERT failure!\r\n"); }
#else
} \
}
#endif // __ROMCC__
-#else // !DEBUG
+#else // !CONFIG_DEBUG
#define ASSERT(x) { }
#endif
#define printk_debug(fmt, arg...) do_printk(BIOS_DEBUG ,fmt, ##arg)
#define printk_spew(fmt, arg...) do_printk(BIOS_SPEW ,fmt, ##arg)
-#if MAXIMUM_CONSOLE_LOGLEVEL <= BIOS_EMERG
+#if CONFIG_MAXIMUM_CONSOLE_LOGLEVEL <= BIOS_EMERG
#undef printk_emerg
#define printk_emerg(fmt, arg...) do {} while(0)
#endif
-#if MAXIMUM_CONSOLE_LOGLEVEL <= BIOS_ALERT
+#if CONFIG_MAXIMUM_CONSOLE_LOGLEVEL <= BIOS_ALERT
#undef printk_alert
#define printk_alert(fmt, arg...) do {} while(0)
#endif
-#if MAXIMUM_CONSOLE_LOGLEVEL <= BIOS_CRIT
+#if CONFIG_MAXIMUM_CONSOLE_LOGLEVEL <= BIOS_CRIT
#undef printk_crit
#define printk_crit(fmt, arg...) do {} while(0)
#endif
-#if MAXIMUM_CONSOLE_LOGLEVEL <= BIOS_ERR
+#if CONFIG_MAXIMUM_CONSOLE_LOGLEVEL <= BIOS_ERR
#undef printk_err
#define printk_err(fmt, arg...) do {} while(0)
#endif
-#if MAXIMUM_CONSOLE_LOGLEVEL <= BIOS_WARNING
+#if CONFIG_MAXIMUM_CONSOLE_LOGLEVEL <= BIOS_WARNING
#undef printk_warning
#define printk_warning(fmt, arg...) do {} while(0)
#endif
-#if MAXIMUM_CONSOLE_LOGLEVEL <= BIOS_NOTICE
+#if CONFIG_MAXIMUM_CONSOLE_LOGLEVEL <= BIOS_NOTICE
#undef printk_notice
#define printk_notice(fmt, arg...) do {} while(0)
#endif
-#if MAXIMUM_CONSOLE_LOGLEVEL <= BIOS_INFO
+#if CONFIG_MAXIMUM_CONSOLE_LOGLEVEL <= BIOS_INFO
#undef printk_info
#define printk_info(fmt, arg...) do {} while(0)
#endif
-#if MAXIMUM_CONSOLE_LOGLEVEL <= BIOS_DEBUG
+#if CONFIG_MAXIMUM_CONSOLE_LOGLEVEL <= BIOS_DEBUG
#undef printk_debug
#define printk_debug(fmt, arg...) do {} while(0)
#endif
-#if MAXIMUM_CONSOLE_LOGLEVEL <= BIOS_SPEW
+#if CONFIG_MAXIMUM_CONSOLE_LOGLEVEL <= BIOS_SPEW
#undef printk_spew
#define printk_spew(fmt, arg...) do {} while(0)
#endif
/* Safe for inclusion in assembly */
-#ifndef MAXIMUM_CONSOLE_LOGLEVEL
-#define MAXIMUM_CONSOLE_LOGLEVEL 8
+#ifndef CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+#define CONFIG_MAXIMUM_CONSOLE_LOGLEVEL 8
#endif
-#ifndef DEFAULT_CONSOLE_LOGLEVEL
-#define DEFAULT_CONSOLE_LOGLEVEL 8 /* anything MORE serious than BIOS_SPEW */
+#ifndef CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+#define CONFIG_DEFAULT_CONSOLE_LOGLEVEL 8 /* anything MORE serious than BIOS_SPEW */
#endif
#ifndef ASM_CONSOLE_LOGLEVEL
-#if (DEFAULT_CONSOLE_LOGLEVEL <= MAXIMUM_CONSOLE_LOGLEVEL)
-#define ASM_CONSOLE_LOGLEVEL DEFAULT_CONSOLE_LOGLEVEL
+#if (CONFIG_DEFAULT_CONSOLE_LOGLEVEL <= CONFIG_MAXIMUM_CONSOLE_LOGLEVEL)
+#define ASM_CONSOLE_LOGLEVEL CONFIG_DEFAULT_CONSOLE_LOGLEVEL
#else
-#define ASM_CONSOLE_LOGLEVEL MAXIMUM_CONSOLE_LOGLEVEL
+#define ASM_CONSOLE_LOGLEVEL CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
#endif
#endif
#include <arch/cpu.h>
-#if K8_REV_F_SUPPORT == 0
+#if CONFIG_K8_REV_F_SUPPORT == 0
static inline int is_cpu_rev_a0(void)
{
return (cpuid_eax(1) & 0xfffef) == 0x0f00;
#endif
-#if K8_REV_F_SUPPORT == 1
+#if CONFIG_K8_REV_F_SUPPORT == 1
//AMD_F0_SUPPORT
static inline int is_cpu_pre_f0(void)
{
void pci_write_config16(device_t dev, unsigned where, uint16_t val);
void pci_write_config32(device_t dev, unsigned where, uint32_t val);
-#if MMCONF_SUPPORT
+#if CONFIG_MMCONF_SUPPORT
uint8_t pci_mmio_read_config8(device_t dev, unsigned where);
uint16_t pci_mmio_read_config16(device_t dev, unsigned where);
uint32_t pci_mmio_read_config32(device_t dev, unsigned where);
#ifndef ASSEMBLY
-#if HAVE_FALLBACK_BOOT == 1
+#if CONFIG_HAVE_FALLBACK_BOOT == 1
void set_boot_successful(void);
#else
#define set_boot_successful()
#ifndef PART_HARD_RESET_H
#define PART_HARD_RESET_H
-#if HAVE_HARD_RESET == 1
+#if CONFIG_HAVE_HARD_RESET == 1
void hard_reset(void);
#else
#define hard_reset() do {} while(0)
#ifndef PART_INIT_TIMER_H
#define PART_DELAY_H
-#if HAVE_INIT_TIMER == 1
+#if CONFIG_HAVE_INIT_TIMER == 1
void init_timer(void);
#else
#define init_timer() do{} while(0)
#ifndef PART_WATCHDOG_H
#define PART_WATCHDOG_H
-#if USE_WATCHDOG_ON_BOOT == 1
+#if CONFIG_USE_WATCHDOG_ON_BOOT == 1
void watchdog_off(void);
#else
#define watchdog_off()
#define PC_CKS_LOC 46
/* Linux bios checksum is built only over bytes 49..125 */
-#ifndef LB_CKS_RANGE_START
-#define LB_CKS_RANGE_START 49
+#ifndef CONFIG_LB_CKS_RANGE_START
+#define CONFIG_LB_CKS_RANGE_START 49
#endif
-#ifndef LB_CKS_RANGE_END
-#define LB_CKS_RANGE_END 125
+#ifndef CONFIG_LB_CKS_RANGE_END
+#define CONFIG_LB_CKS_RANGE_END 125
#endif
-#ifndef LB_CKS_LOC
-#define LB_CKS_LOC 126
+#ifndef CONFIG_LB_CKS_LOC
+#define CONFIG_LB_CKS_LOC 126
#endif
#if !defined(ASSEMBLY)
void rtc_init(int invalid);
-#if USE_OPTION_TABLE == 1
+#if CONFIG_USE_OPTION_TABLE == 1
int get_option(void *dest, char *name);
#else
static inline int get_option(void *dest, char *name) { return -2; }
#define __X86EMU_FPU_REGS_H
-#if defined(DEBUG) && (DEBUG == 0)
-#undef DEBUG
+#if defined(CONFIG_DEBUG) && (DEBUG == 0)
+#undef CONFIG_DEBUG
#endif
#ifdef X86_FPU_SUPPORT
#endif /* X86_FPU_SUPPORT */
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
# define DECODE_PRINTINSTR32(t,mod,rh,rl) \
DECODE_PRINTF(t[(mod<<3)+(rh)]);
# define DECODE_PRINTINSTR256(t,mod,rh,rl) \
#ifndef __X86EMU_REGS_H
#define __X86EMU_REGS_H
-#if defined(DEBUG) && (DEBUG == 0)
-#undef DEBUG
+#if defined(CONFIG_DEBUG) && (CONFIG_DEBUG == 0)
+#undef CONFIG_DEBUG
#endif
/*---------------------- Macros and type definitions ----------------------*/
u32 mode;
volatile int intr; /* mask of pending interrupts */
volatile int debug;
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
int check;
u16 saved_ip;
u16 saved_cs;
#ifndef __X86EMU_X86EMU_H
#define __X86EMU_X86EMU_H
-#if defined(DEBUG) && (DEBUG == 0)
-#undef DEBUG
+#if defined(CONFIG_DEBUG) && (CONFIG_DEBUG == 0)
+#undef CONFIG_DEBUG
#endif
/* FIXME: undefine printk for the moment */
void X86EMU_exec(void);
void X86EMU_halt_sys(void);
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
#define HALT_SYS() \
printk("halt_sys: file %s, line %d\n", __FILE__, __LINE__); \
X86EMU_halt_sys();
#include <arch/io.h>
-#if HAVE_FALLBACK_BOOT == 1
+#if CONFIG_HAVE_FALLBACK_BOOT == 1
void set_boot_successful(void)
{
/* Remember I succesfully booted by setting
int lcs;
divisor = 115200/(uart->baud ? uart->baud: 1);
lcs = 3;
- if (base_port == TTYS0_BASE) {
+ if (base_port == CONFIG_TTYS0_BASE) {
/* Don't reinitialize the console serial port,
* This is espeically nasty in SMP.
*/
#include <version.h>
-#ifndef MAINBOARD_VENDOR
-#error MAINBOARD_VENDOR not defined
+#ifndef CONFIG_MAINBOARD_VENDOR
+#error CONFIG_MAINBOARD_VENDOR not defined
#endif
-#ifndef MAINBOARD_PART_NUMBER
-#error MAINBOARD_PART_NUMBER not defined
+#ifndef CONFIG_MAINBOARD_PART_NUMBER
+#error CONFIG_MAINBOARD_PART_NUMBER not defined
#endif
#ifndef COREBOOT_VERSION
#define COREBOOT_EXTRA_VERSION ""
#endif
-const char mainboard_vendor[] = MAINBOARD_VENDOR;
-const char mainboard_part_number[] = MAINBOARD_PART_NUMBER;
+const char mainboard_vendor[] = CONFIG_MAINBOARD_VENDOR;
+const char mainboard_part_number[] = CONFIG_MAINBOARD_PART_NUMBER;
const char coreboot_version[] = COREBOOT_VERSION;
const char coreboot_extra_version[] = COREBOOT_EXTRA_VERSION;
static int _inbyte(int msec)
{
- while (!uart8250_can_rx_byte(TTYS0_BASE)) {
+ while (!uart8250_can_rx_byte(CONFIG_TTYS0_BASE)) {
udelay(1000);
if (msec-- <= 0)
return -1;
}
- return uart8250_rx_byte(TTYS0_BASE);
+ return uart8250_rx_byte(CONFIG_TTYS0_BASE);
}
static void _outbyte(unsigned char c)
{
- uart8250_tx_byte(TTYS0_BASE, c);
+ uart8250_tx_byte(CONFIG_TTYS0_BASE, c);
}
static unsigned short crc16_ccitt(const unsigned char *buf, int sz)
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
arch i386 end
driver mainboard.o
-if HAVE_PIRQ_TABLE
+if CONFIG_HAVE_PIRQ_TABLE
object irq_tables.o
end
makerule ./failover.E
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -E -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -E -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./auto.E
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -E -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -E -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
mainboardinit cpu/x86/16bit/entry16.inc
mainboardinit cpu/x86/32bit/entry32.inc
ldscript /cpu/x86/16bit/entry16.lds
ldscript /cpu/x86/32bit/entry32.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
mainboardinit arch/i386/lib/cpu_reset.inc
mainboardinit arch/i386/lib/id.inc
ldscript /arch/i386/lib/id.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_ROM_PAYLOAD
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses HAVE_MP_TABLE
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
-default ROM_SIZE = 256 * 1024
-default HAVE_FALLBACK_BOOT = 1
-default HAVE_MP_TABLE = 0
-default HAVE_HARD_RESET = 0
+default CONFIG_ROM_SIZE = 256 * 1024
+default CONFIG_HAVE_FALLBACK_BOOT = 1
+default CONFIG_HAVE_MP_TABLE = 0
+default CONFIG_HAVE_HARD_RESET = 0
default CONFIG_UDELAY_TSC = 1
default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 1
-default HAVE_PIRQ_TABLE = 1
-default IRQ_SLOT_COUNT = 0 # Override this in targets/*/Config.lb.
-default MAINBOARD_VENDOR = "N/A" # Override this in targets/*/Config.lb.
-default MAINBOARD_PART_NUMBER = "N/A" # Override this in targets/*/Config.lb.
-default ROM_IMAGE_SIZE = 64 * 1024
-default FALLBACK_SIZE = 128 * 1024
-default STACK_SIZE = 8 * 1024
-default HEAP_SIZE = 16 * 1024
-default HAVE_OPTION_TABLE = 0
-#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_HAVE_PIRQ_TABLE = 1
+default CONFIG_IRQ_SLOT_COUNT = 0 # Override this in targets/*/Config.lb.
+default CONFIG_MAINBOARD_VENDOR = "N/A" # Override this in targets/*/Config.lb.
+default CONFIG_MAINBOARD_PART_NUMBER = "N/A" # Override this in targets/*/Config.lb.
+default CONFIG_ROM_IMAGE_SIZE = 64 * 1024
+default CONFIG_FALLBACK_SIZE = 128 * 1024
+default CONFIG_STACK_SIZE = 8 * 1024
+default CONFIG_HEAP_SIZE = 16 * 1024
+default CONFIG_HAVE_OPTION_TABLE = 0
+#default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 0
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
-default CROSS_COMPILE = ""
-default CC = "$(CROSS_COMPILE)gcc -m32"
-default HOSTCC = "gcc"
+default CONFIG_CROSS_COMPILE = ""
+default CC = "$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC = "gcc"
default CONFIG_CONSOLE_SERIAL8250 = 1
-default TTYS0_BAUD = 115200
-default TTYS0_BASE = 0x3f8
-default TTYS0_LCS = 0x3 # 8n1
-default DEFAULT_CONSOLE_LOGLEVEL = 9
-default MAXIMUM_CONSOLE_LOGLEVEL = 9
+default CONFIG_TTYS0_BAUD = 115200
+default CONFIG_TTYS0_BASE = 0x3f8
+default CONFIG_TTYS0_LCS = 0x3 # 8n1
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
default CONFIG_CONSOLE_VGA = 1
default CONFIG_PCI_ROM_RUN = 1
if (bist == 0)
early_mtrr_init();
- w83977tf_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ w83977tf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
report_bist_failure(bist);
const struct irq_routing_table intel_irq_routing_table = {
PIRQ_SIGNATURE,
PIRQ_VERSION,
- 32 + 16 * IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
+ 32 + 16 * CONFIG_IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
0x00, /* Interrupt router bus */
(0x07 << 3) | 0x0, /* Interrupt router device */
0x600, /* IRQs devoted exclusively to PCI usage */
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
arch i386 end
driver mainboard.o
-if HAVE_PIRQ_TABLE
+if CONFIG_HAVE_PIRQ_TABLE
object irq_tables.o
end
makerule ./failover.E
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -E -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -E -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./auto.E
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -E -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -E -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
mainboardinit cpu/x86/16bit/entry16.inc
mainboardinit cpu/x86/32bit/entry32.inc
ldscript /cpu/x86/16bit/entry16.lds
ldscript /cpu/x86/32bit/entry32.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
mainboardinit arch/i386/lib/cpu_reset.inc
mainboardinit arch/i386/lib/id.inc
ldscript /arch/i386/lib/id.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_ROM_PAYLOAD
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses HAVE_MP_TABLE
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
-default ROM_SIZE = 256 * 1024
-default HAVE_FALLBACK_BOOT = 1
-default HAVE_MP_TABLE = 0
-default HAVE_HARD_RESET = 0
+default CONFIG_ROM_SIZE = 256 * 1024
+default CONFIG_HAVE_FALLBACK_BOOT = 1
+default CONFIG_HAVE_MP_TABLE = 0
+default CONFIG_HAVE_HARD_RESET = 0
default CONFIG_UDELAY_TSC = 1
default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 1
-default HAVE_PIRQ_TABLE = 1
-default IRQ_SLOT_COUNT = 0 # Override this in targets/*/Config.lb.
-default MAINBOARD_VENDOR = "N/A" # Override this in targets/*/Config.lb.
-default MAINBOARD_PART_NUMBER = "N/A" # Override this in targets/*/Config.lb.
-default ROM_IMAGE_SIZE = 64 * 1024
-default FALLBACK_SIZE = 128 * 1024
-default STACK_SIZE = 8 * 1024
-default HEAP_SIZE = 16 * 1024
-default HAVE_OPTION_TABLE = 0
-#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_HAVE_PIRQ_TABLE = 1
+default CONFIG_IRQ_SLOT_COUNT = 0 # Override this in targets/*/Config.lb.
+default CONFIG_MAINBOARD_VENDOR = "N/A" # Override this in targets/*/Config.lb.
+default CONFIG_MAINBOARD_PART_NUMBER = "N/A" # Override this in targets/*/Config.lb.
+default CONFIG_ROM_IMAGE_SIZE = 64 * 1024
+default CONFIG_FALLBACK_SIZE = 128 * 1024
+default CONFIG_STACK_SIZE = 8 * 1024
+default CONFIG_HEAP_SIZE = 16 * 1024
+default CONFIG_HAVE_OPTION_TABLE = 0
+#default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 0
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
-default CROSS_COMPILE = ""
-default CC = "$(CROSS_COMPILE)gcc -m32"
-default HOSTCC = "gcc"
+default CONFIG_CROSS_COMPILE = ""
+default CC = "$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC = "gcc"
default CONFIG_CONSOLE_SERIAL8250 = 1
-default TTYS0_BAUD = 115200
-default TTYS0_BASE = 0x3f8
-default TTYS0_LCS = 0x3 # 8n1
-default DEFAULT_CONSOLE_LOGLEVEL = 9
-default MAXIMUM_CONSOLE_LOGLEVEL = 9
+default CONFIG_TTYS0_BAUD = 115200
+default CONFIG_TTYS0_BASE = 0x3f8
+default CONFIG_TTYS0_LCS = 0x3 # 8n1
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
default CONFIG_CONSOLE_VGA = 1
default CONFIG_PCI_ROM_RUN = 1
if (bist == 0)
early_mtrr_init();
- w83627hf_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ w83627hf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
report_bist_failure(bist);
const struct irq_routing_table intel_irq_routing_table = {
PIRQ_SIGNATURE,
PIRQ_VERSION,
- 32 + 16 * IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
+ 32 + 16 * CONFIG_IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
0x00, /* Interrupt router bus */
(0x07 << 3) | 0x0, /* Interrupt router device */
0xc20, /* IRQs devoted exclusively to PCI usage */
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
arch i386 end
driver mainboard.o
-if HAVE_PIRQ_TABLE
+if CONFIG_HAVE_PIRQ_TABLE
object irq_tables.o
end
makerule ./failover.E
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -E -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -E -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./auto.E
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -E -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -E -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
mainboardinit cpu/x86/16bit/entry16.inc
mainboardinit cpu/x86/32bit/entry32.inc
ldscript /cpu/x86/16bit/entry16.lds
ldscript /cpu/x86/32bit/entry32.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
mainboardinit arch/i386/lib/cpu_reset.inc
mainboardinit arch/i386/lib/id.inc
ldscript /arch/i386/lib/id.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_ROM_PAYLOAD
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses HAVE_MP_TABLE
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
-default ROM_SIZE = 256 * 1024 # Override this in targets/*/Config.lb.
-default HAVE_FALLBACK_BOOT = 1
-default HAVE_MP_TABLE = 0
-default HAVE_HARD_RESET = 0
+default CONFIG_ROM_SIZE = 256 * 1024 # Override this in targets/*/Config.lb.
+default CONFIG_HAVE_FALLBACK_BOOT = 1
+default CONFIG_HAVE_MP_TABLE = 0
+default CONFIG_HAVE_HARD_RESET = 0
default CONFIG_UDELAY_TSC = 1
default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 1
-default HAVE_PIRQ_TABLE = 1
-default IRQ_SLOT_COUNT = 0 # Override this in targets/*/Config.lb.
-default MAINBOARD_VENDOR = "N/A" # Override this in targets/*/Config.lb.
-default MAINBOARD_PART_NUMBER = "N/A" # Override this in targets/*/Config.lb.
-default ROM_IMAGE_SIZE = 64 * 1024
-default FALLBACK_SIZE = 128 * 1024
-default STACK_SIZE = 8 * 1024
-default HEAP_SIZE = 16 * 1024
-default HAVE_OPTION_TABLE = 0
-#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_HAVE_PIRQ_TABLE = 1
+default CONFIG_IRQ_SLOT_COUNT = 0 # Override this in targets/*/Config.lb.
+default CONFIG_MAINBOARD_VENDOR = "N/A" # Override this in targets/*/Config.lb.
+default CONFIG_MAINBOARD_PART_NUMBER = "N/A" # Override this in targets/*/Config.lb.
+default CONFIG_ROM_IMAGE_SIZE = 64 * 1024
+default CONFIG_FALLBACK_SIZE = 128 * 1024
+default CONFIG_STACK_SIZE = 8 * 1024
+default CONFIG_HEAP_SIZE = 16 * 1024
+default CONFIG_HAVE_OPTION_TABLE = 0
+#default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 0
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
-default CROSS_COMPILE = ""
-default CC = "$(CROSS_COMPILE)gcc -m32"
-default HOSTCC = "gcc"
+default CONFIG_CROSS_COMPILE = ""
+default CC = "$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC = "gcc"
default CONFIG_CONSOLE_SERIAL8250 = 1
-default TTYS0_BAUD = 115200
-default TTYS0_BASE = 0x3f8
-default TTYS0_LCS = 0x3 # 8n1
-default DEFAULT_CONSOLE_LOGLEVEL = 9 # Override this in targets/*/Config.lb.
-default MAXIMUM_CONSOLE_LOGLEVEL = 9 # Override this in targets/*/Config.lb.
+default CONFIG_TTYS0_BAUD = 115200
+default CONFIG_TTYS0_BASE = 0x3f8
+default CONFIG_TTYS0_LCS = 0x3 # 8n1
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9 # Override this in targets/*/Config.lb.
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9 # Override this in targets/*/Config.lb.
default CONFIG_CONSOLE_VGA = 1 # Override this in targets/*/Config.lb.
default CONFIG_PCI_ROM_RUN = 1 # Override this in targets/*/Config.lb.
early_mtrr_init();
/* FIXME: It's a Winbond W83977EF, actually. */
- w83977tf_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ w83977tf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
report_bist_failure(bist);
const struct irq_routing_table intel_irq_routing_table = {
PIRQ_SIGNATURE,
PIRQ_VERSION,
- 32 + 16 * IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
+ 32 + 16 * CONFIG_IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
0x00, /* Interrupt router bus */
(0x07 << 3) | 0x0, /* Interrupt router device */
0x1c20, /* IRQs devoted exclusively to PCI usage */
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
arch i386 end
driver mainboard.o
-if HAVE_PIRQ_TABLE
+if CONFIG_HAVE_PIRQ_TABLE
object irq_tables.o
end
makerule ./failover.E
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./auto.E
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -E -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -E -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
mainboardinit cpu/x86/16bit/entry16.inc
mainboardinit cpu/x86/32bit/entry32.inc
ldscript /cpu/x86/16bit/entry16.lds
ldscript /cpu/x86/32bit/entry32.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
mainboardinit arch/i386/lib/cpu_reset.inc
mainboardinit arch/i386/lib/id.inc
ldscript /arch/i386/lib/id.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_ROM_PAYLOAD
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
uses CONFIG_SPLASH_GRAPHIC
uses CONFIG_GX1_VIDEO
uses CONFIG_GX1_VIDEOMODE
-uses PIRQ_ROUTE
+uses CONFIG_PIRQ_ROUTE
## Enable VGA with a splash screen (only 640x480 to run on most monitors).
## We want to support up to 1024x768@16 so we need 2MiB video memory.
default CONFIG_SPLASH_GRAPHIC = 1
default CONFIG_VIDEO_MB = 2
-default ROM_SIZE = 256 * 1024
-default HAVE_PIRQ_TABLE = 1
-default IRQ_SLOT_COUNT = 0 # Override this in targets/*/Config.lb.
-default PIRQ_ROUTE = 1
-default HAVE_FALLBACK_BOOT = 1
-default HAVE_MP_TABLE = 0
-default HAVE_HARD_RESET = 0
+default CONFIG_ROM_SIZE = 256 * 1024
+default CONFIG_HAVE_PIRQ_TABLE = 1
+default CONFIG_IRQ_SLOT_COUNT = 0 # Override this in targets/*/Config.lb.
+default CONFIG_PIRQ_ROUTE = 1
+default CONFIG_HAVE_FALLBACK_BOOT = 1
+default CONFIG_HAVE_MP_TABLE = 0
+default CONFIG_HAVE_HARD_RESET = 0
default CONFIG_UDELAY_TSC = 1
default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 1
-default HAVE_OPTION_TABLE = 0
-default MAINBOARD_VENDOR = "N/A" # Override this in targets/*/Config.lb.
-default MAINBOARD_PART_NUMBER = "N/A" # Override this in targets/*/Config.lb.
-default ROM_IMAGE_SIZE = 64 * 1024
-default FALLBACK_SIZE = 128 * 1024
-default STACK_SIZE = 8 * 1024
-default HEAP_SIZE = 16 * 1024
-default USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_HAVE_OPTION_TABLE = 0
+default CONFIG_MAINBOARD_VENDOR = "N/A" # Override this in targets/*/Config.lb.
+default CONFIG_MAINBOARD_PART_NUMBER = "N/A" # Override this in targets/*/Config.lb.
+default CONFIG_ROM_IMAGE_SIZE = 64 * 1024
+default CONFIG_FALLBACK_SIZE = 128 * 1024
+default CONFIG_STACK_SIZE = 8 * 1024
+default CONFIG_HEAP_SIZE = 16 * 1024
+default CONFIG_USE_OPTION_TABLE = 0
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
-default CROSS_COMPILE = ""
-default CC = "$(CROSS_COMPILE)gcc "
-default HOSTCC = "gcc"
+default CONFIG_CROSS_COMPILE = ""
+default CC = "$(CONFIG_CROSS_COMPILE)gcc "
+default CONFIG_HOSTCC = "gcc"
default CONFIG_CONSOLE_SERIAL8250 = 1
-default TTYS0_BAUD = 115200
-default TTYS0_BASE = 0x3f8
-default TTYS0_LCS = 0x3 # 8n1
-default DEFAULT_CONSOLE_LOGLEVEL = 9
-default MAXIMUM_CONSOLE_LOGLEVEL = 9
+default CONFIG_TTYS0_BAUD = 115200
+default CONFIG_TTYS0_BASE = 0x3f8
+default CONFIG_TTYS0_LCS = 0x3 # 8n1
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
#
# CBFS
static void main(unsigned long bist)
{
- w83977f_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ w83977f_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
report_bist_failure(bist);
const struct irq_routing_table intel_irq_routing_table = {
PIRQ_SIGNATURE,
PIRQ_VERSION,
- 32 + 16 * IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
+ 32 + 16 * CONFIG_IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
0x00, /* Interrupt router bus */
(0x12 << 3) | 0x0, /* Interrupt router device */
0xc00, /* IRQs devoted exclusively to PCI usage */
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
##
driver mainboard.o
-if HAVE_PIRQ_TABLE
+if CONFIG_HAVE_PIRQ_TABLE
object irq_tables.o
end
#compile cache_as_ram.c to auto.inc
makerule ./cache_as_ram_auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
# mainboardinit ./failover.inc
end
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_ROM_PAYLOAD
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_NRV2B
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses HAVE_MP_TABLE
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
uses CONFIG_VIDEO_MB
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
uses CONFIG_USE_PRINTK_IN_CAR
-uses PIRQ_ROUTE
+uses CONFIG_PIRQ_ROUTE
-## ROM_SIZE is the size of boot ROM that this board will use.
-default ROM_SIZE = 256*1024
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
+default CONFIG_ROM_SIZE = 256*1024
###
### Build options
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## no MP table
##
-default HAVE_MP_TABLE=0
+default CONFIG_HAVE_MP_TABLE=0
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=0
+default CONFIG_HAVE_HARD_RESET=0
## Delay timer options
##
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=4
-default PIRQ_ROUTE=1
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=4
+default CONFIG_PIRQ_ROUTE=1
#object irq_tables.o
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=0
+default CONFIG_HAVE_OPTION_TABLE=0
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
-default FALLBACK_SIZE = 131072
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
+default CONFIG_FALLBACK_SIZE = 131072
##
## enable CACHE_AS_RAM specifics
##
-default USE_DCACHE_RAM=1
-default DCACHE_RAM_BASE=0xc8000
-default DCACHE_RAM_SIZE=0x08000
+default CONFIG_USE_DCACHE_RAM=1
+default CONFIG_DCACHE_RAM_BASE=0xc8000
+default CONFIG_DCACHE_RAM_SIZE=0x08000
default CONFIG_USE_PRINTK_IN_CAR=1
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE=0x4000
+default CONFIG_HEAP_SIZE=0x4000
##
## Only use the option table in a normal image
##
-#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
+#default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
##
## The default compiler
##
-default CROSS_COMPILE=""
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CONFIG_CROSS_COMPILE=""
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## The Serial Console
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
#
/* Note: must do this AFTER the early_setup! It is counting on some
* early MSR setup for CS5536.
*/
- w83627hf_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ w83627hf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
mb_gpio_init();
uart_init();
console_init();
const struct irq_routing_table intel_irq_routing_table = {
PIRQ_SIGNATURE, /* u32 signature */
PIRQ_VERSION, /* u16 version */
- 32 + 16 * IRQ_SLOT_COUNT, /* there can be total 6 devices on the bus */
+ 32 + 16 * CONFIG_IRQ_SLOT_COUNT, /* there can be total 6 devices on the bus */
0x00, /* Where the interrupt router lies (bus) */
(0x0F << 3) | 0x0, /* Where the interrupt router lies (dev) */
0x00, /* IRQs devoted exclusively to PCI usage */
{0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0}, /* u8 rfu[11] */
0x00, /* u8 checksum , this has to set to some value that would give 0 after the sum of all bytes for this structure (including checksum) */
{
- /* If you change the number of entries, change the IRQ_SLOT_COUNT above! */
+ /* If you change the number of entries, change the CONFIG_IRQ_SLOT_COUNT above! */
/* bus, dev|fn, {link, bitmap}, {link, bitmap}, {link, bitmap}, {link, bitmap}, slot, rfu */
{0x00, (0x01 << 3) | 0x0, {{L_PIRQA, M_PIRQA}, {0x00, 0x00}, {0x00, 0x00}, {0x00, 0x00}}, 0x0, 0x0}, /* cpu */
{0x00, (0x0F << 3) | 0x0, {{L_PIRQA, M_PIRQA}, {L_PIRQB, M_PIRQB}, {L_PIRQC, M_PIRQC}, {L_PIRQD, M_PIRQD}}, 0x0, 0x0}, /* chipset */
##
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
arch i386 end
#dir /drivers/si/3114
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE
object get_bus_conf.o
object irq_tables.o
end
-if HAVE_ACPI_TABLES
+if CONFIG_HAVE_ACPI_TABLES
object acpi_tables.o
object fadt.o
makerule dsdt.c
- depends "$(MAINBOARD)/acpi/*.asl"
- action "iasl -p $(CURDIR)/dsdt -tc $(MAINBOARD)/acpi/dsdt.asl"
+ depends "$(CONFIG_MAINBOARD)/acpi/*.asl"
+ action "iasl -p $(CURDIR)/dsdt -tc $(CONFIG_MAINBOARD)/acpi/dsdt.asl"
action "mv dsdt.hex dsdt.c"
end
object ./dsdt.o
if CONFIG_USE_INIT
makerule ./cache_as_ram_auto.o
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
end
else
makerule ./cache_as_ram_auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
end
##
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses HAVE_ACPI_TABLES
-uses HAVE_ACPI_RESUME
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_HAVE_ACPI_TABLES
+uses CONFIG_HAVE_ACPI_RESUME
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_MAX_CPUS
uses CONFIG_MAX_PHYSICAL_CPUS
uses CONFIG_LOGICAL_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
-uses _RAMBASE
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_RAMBASE
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_SERIAL8250
-uses HAVE_INIT_TIMER
+uses CONFIG_HAVE_INIT_TIMER
uses CONFIG_GDB_STUB
uses CONFIG_GDB_STUB
-uses CROSS_COMPILE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
-uses HW_MEM_HOLE_SIZEK
-uses HT_CHAIN_UNITID_BASE
-uses HT_CHAIN_END_UNITID_BASE
-uses SB_HT_CHAIN_ON_BUS0
-
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
-uses DCACHE_RAM_GLOBAL_VAR_SIZE
+uses CONFIG_HW_MEM_HOLE_SIZEK
+uses CONFIG_HT_CHAIN_UNITID_BASE
+uses CONFIG_HT_CHAIN_END_UNITID_BASE
+uses CONFIG_SB_HT_CHAIN_ON_BUS0
+
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
+uses CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE
uses CONFIG_USE_INIT
-uses SB_HT_CHAIN_UNITID_OFFSET_ONLY
+uses CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY
uses CONFIG_USE_PRINTK_IN_CAR
uses CONFIG_VIDEO_MB
uses CONFIG_GFXUMA
-uses HAVE_MAINBOARD_RESOURCES
+uses CONFIG_HAVE_MAINBOARD_RESOURCES
###
### Build options
###
##
-## ROM_SIZE is the size of boot ROM that this board will use.
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
##
-default ROM_SIZE=524288
+default CONFIG_ROM_SIZE=524288
##
-## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
+## CONFIG_FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
##
-#default FALLBACK_SIZE=131072
+#default CONFIG_FALLBACK_SIZE=131072
#256K
-default FALLBACK_SIZE=0x40000
+default CONFIG_FALLBACK_SIZE=0x40000
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=11
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=11
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
## ACPI tables will be included
-default HAVE_ACPI_TABLES=1
+default CONFIG_HAVE_ACPI_TABLES=1
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=0
+default CONFIG_HAVE_OPTION_TABLE=0
##
## Move the default coreboot cmos range off of AMD RTC registers
##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
+default CONFIG_LB_CKS_RANGE_START=49
+default CONFIG_LB_CKS_RANGE_END=122
+default CONFIG_LB_CKS_LOC=123
##
## Build code for SMP support
default CONFIG_LOGICAL_CPUS=1
#1G memory hole
-default HW_MEM_HOLE_SIZEK=0x100000
+default CONFIG_HW_MEM_HOLE_SIZEK=0x100000
#VGA Console
default CONFIG_CONSOLE_VGA=1
# BTDC: Only one HT device on Herring.
#HT Unit ID offset
-#default HT_CHAIN_UNITID_BASE=0x6
-default HT_CHAIN_UNITID_BASE=0x0
+#default CONFIG_HT_CHAIN_UNITID_BASE=0x6
+default CONFIG_HT_CHAIN_UNITID_BASE=0x0
#real SB Unit ID
-default HT_CHAIN_END_UNITID_BASE=0x1
+default CONFIG_HT_CHAIN_END_UNITID_BASE=0x1
#make the SB HT chain on bus 0
-default SB_HT_CHAIN_ON_BUS0=1
+default CONFIG_SB_HT_CHAIN_ON_BUS0=1
##
## enable CACHE_AS_RAM specifics
##
-default USE_DCACHE_RAM=1
-default DCACHE_RAM_BASE=0xc8000
-default DCACHE_RAM_SIZE=0x8000
-default DCACHE_RAM_GLOBAL_VAR_SIZE=0x01000
+default CONFIG_USE_DCACHE_RAM=1
+default CONFIG_DCACHE_RAM_BASE=0xc8000
+default CONFIG_DCACHE_RAM_SIZE=0x8000
+default CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE=0x01000
default CONFIG_USE_INIT=0
##
##
## Clean up the motherboard id strings
##
-default MAINBOARD_PART_NUMBER="dbm690t"
-default MAINBOARD_VENDOR="amd"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x1022
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x3050
+default CONFIG_MAINBOARD_PART_NUMBER="dbm690t"
+default CONFIG_MAINBOARD_VENDOR="amd"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x1022
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x3050
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE=0x4000
+default CONFIG_HEAP_SIZE=0x4000
##
## Only use the option table in a normal image
##
-#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
+#default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 0
##
## coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00004000
+default CONFIG_RAMBASE=0x00004000
##
## Load the payload from the ROM
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## Disable the gdb stub by default
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
default CONFIG_VIDEO_MB=1
default CONFIG_GFXUMA=1
-default HAVE_MAINBOARD_RESOURCES=1
+default CONFIG_HAVE_MAINBOARD_RESOURCES=1
### End Options.lb
#
extern u8 AmlCode[];
-#if ACPI_SSDTX_NUM >= 1
+#if CONFIG_ACPI_SSDTX_NUM >= 1
extern u8 AmlCode_ssdt2[];
extern u8 AmlCode_ssdt3[];
extern u8 AmlCode_ssdt4[];
current += ssdt->length;
acpi_add_table(rsdt, ssdt);
-#if ACPI_SSDTX_NUM >= 1
+#if CONFIG_ACPI_SSDTX_NUM >= 1
/* same htio, but different position? We may have to copy, change HCIN, and recalculate the checknum and add_table */
#include "cpu/amd/model_fxx/fidvid.c"
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
#include "northbridge/amd/amdk8/early_ht.c"
fallback_image:
post_code(0x25);
}
-#endif /* USE_FALLBACK_IMAGE == 1 */
+#endif /* CONFIG_USE_FALLBACK_IMAGE == 1 */
void real_main(unsigned long bist, unsigned long cpu_init_detectedx);
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
failover_process(bist, cpu_init_detectedx);
#endif
real_main(bist, cpu_init_detectedx);
u32 bsp_apicid = 0;
msr_t msr;
struct cpuid_result cpuid1;
- struct sys_info *sysinfo = (struct sys_info *)(DCACHE_RAM_BASE + DCACHE_RAM_SIZE - DCACHE_RAM_GLOBAL_VAR_SIZE);
+ struct sys_info *sysinfo = (struct sys_info *)(CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE);
if (bist == 0) {
sb600_lpc_init();
/* it8712f_enable_serial does not use its 1st parameter. */
- it8712f_enable_serial(0, TTYS0_BASE);
+ it8712f_enable_serial(0, CONFIG_TTYS0_BASE);
uart_init();
console_init();
/* PCI interrupts are level triggered, and are
* associated with a specific bus/device/function tuple.
*/
-#if HAVE_ACPI_TABLES == 0
+#if CONFIG_HAVE_ACPI_TABLES == 0
#define PCI_INT(bus, dev, fn, pin) \
smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, (bus), (((dev)<<2)|(fn)), apicid_sb600, (pin))
#else
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
##
driver mainboard.o
-if HAVE_PIRQ_TABLE
+if CONFIG_HAVE_PIRQ_TABLE
object irq_tables.o
end
#compile cache_as_ram.c to auto.inc
makerule ./cache_as_ram_auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
# mainboardinit ./failover.inc
end
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_ROM_PAYLOAD
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_NRV2B
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses HAVE_MP_TABLE
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
uses CONFIG_VIDEO_MB
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
uses CONFIG_USE_PRINTK_IN_CAR
-uses PIRQ_ROUTE
+uses CONFIG_PIRQ_ROUTE
-## ROM_SIZE is the size of boot ROM that this board will use.
-default ROM_SIZE = 256*1024
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
+default CONFIG_ROM_SIZE = 256*1024
###
### Build options
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## no MP table
##
-default HAVE_MP_TABLE=0
+default CONFIG_HAVE_MP_TABLE=0
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=0
+default CONFIG_HAVE_HARD_RESET=0
## Delay timer options
##
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=6
-default PIRQ_ROUTE=1
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=6
+default CONFIG_PIRQ_ROUTE=1
#object irq_tables.o
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=0
+default CONFIG_HAVE_OPTION_TABLE=0
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
-default FALLBACK_SIZE = 131072
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
+default CONFIG_FALLBACK_SIZE = 131072
##
## enable CACHE_AS_RAM specifics
##
-default USE_DCACHE_RAM=1
-default DCACHE_RAM_BASE=0xc8000
-default DCACHE_RAM_SIZE=0x08000
+default CONFIG_USE_DCACHE_RAM=1
+default CONFIG_DCACHE_RAM_BASE=0xc8000
+default CONFIG_DCACHE_RAM_SIZE=0x08000
default CONFIG_USE_PRINTK_IN_CAR=1
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE=0x4000
+default CONFIG_HEAP_SIZE=0x4000
##
## Only use the option table in a normal image
##
-#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
+#default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
##
## The default compiler
##
-default CROSS_COMPILE=""
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CONFIG_CROSS_COMPILE=""
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## The Serial Console
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
#
const struct irq_routing_table intel_irq_routing_table = {
PIRQ_SIGNATURE, /* u32 signature */
PIRQ_VERSION, /* u16 version */
- 32 + 16 * IRQ_SLOT_COUNT, /* there can be total 6 devices on the bus */
+ 32 + 16 * CONFIG_IRQ_SLOT_COUNT, /* there can be total 6 devices on the bus */
0x00, /* Where the interrupt router lies (bus) */
(0x0F << 3) | 0x0, /* Where the interrupt router lies (dev) */
0x00, /* IRQs devoted exclusively to PCI usage */
{0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0}, /* u8 rfu[11] */
0x00, /* u8 checksum , this has to set to some value that would give 0 after the sum of all bytes for this structure (including checksum) */
{
- /* If you change the number of entries, change the IRQ_SLOT_COUNT above! */
+ /* If you change the number of entries, change the CONFIG_IRQ_SLOT_COUNT above! */
/* bus, dev|fn, {link, bitmap}, {link, bitmap}, {link, bitmap}, {link, bitmap}, slot, rfu */
{0x00, (0x01 << 3) | 0x0, {{L_PIRQA, M_PIRQA}, {0x00, 0x00}, {0x00, 0x00}, {0x00, 0x00}}, 0x0, 0x0}, /* cpu */
{0x00, (0x0F << 3) | 0x0, {{L_PIRQA, M_PIRQA}, {L_PIRQB, M_PIRQB}, {L_PIRQC, M_PIRQC}, {L_PIRQD, M_PIRQD}}, 0x0, 0x0}, /* chipset */
##
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
arch i386 end
#dir /drivers/si/3114
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE
object get_bus_conf.o
object irq_tables.o
end
-if HAVE_ACPI_TABLES
+if CONFIG_HAVE_ACPI_TABLES
object acpi_tables.o
object fadt.o
makerule dsdt.c
- depends "$(MAINBOARD)/acpi/*.asl"
- action "iasl -p $(CURDIR)/dsdt -tc $(MAINBOARD)/acpi/dsdt.asl"
+ depends "$(CONFIG_MAINBOARD)/acpi/*.asl"
+ action "iasl -p $(CURDIR)/dsdt -tc $(CONFIG_MAINBOARD)/acpi/dsdt.asl"
action "mv dsdt.hex dsdt.c"
end
object ./dsdt.o
if CONFIG_USE_INIT
makerule ./cache_as_ram_auto.o
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
end
else
makerule ./cache_as_ram_auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
end
##
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses HAVE_ACPI_TABLES
-uses HAVE_ACPI_RESUME
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_HAVE_ACPI_TABLES
+uses CONFIG_HAVE_ACPI_RESUME
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_MAX_CPUS
uses CONFIG_MAX_PHYSICAL_CPUS
uses CONFIG_LOGICAL_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
-uses _RAMBASE
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_RAMBASE
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_SERIAL8250
-uses HAVE_INIT_TIMER
+uses CONFIG_HAVE_INIT_TIMER
uses CONFIG_GDB_STUB
uses CONFIG_GDB_STUB
-uses CROSS_COMPILE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
-uses HW_MEM_HOLE_SIZEK
-uses HT_CHAIN_UNITID_BASE
-uses HT_CHAIN_END_UNITID_BASE
-uses SB_HT_CHAIN_ON_BUS0
-
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
-uses DCACHE_RAM_GLOBAL_VAR_SIZE
+uses CONFIG_HW_MEM_HOLE_SIZEK
+uses CONFIG_HT_CHAIN_UNITID_BASE
+uses CONFIG_HT_CHAIN_END_UNITID_BASE
+uses CONFIG_SB_HT_CHAIN_ON_BUS0
+
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
+uses CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE
uses CONFIG_USE_INIT
-uses SB_HT_CHAIN_UNITID_OFFSET_ONLY
+uses CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY
uses CONFIG_USE_PRINTK_IN_CAR
uses CONFIG_VIDEO_MB
uses CONFIG_GFXUMA
-uses HAVE_MAINBOARD_RESOURCES
+uses CONFIG_HAVE_MAINBOARD_RESOURCES
###
### Build options
###
##
-## ROM_SIZE is the size of boot ROM that this board will use.
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
##
-default ROM_SIZE=524288
+default CONFIG_ROM_SIZE=524288
##
-## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
+## CONFIG_FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
##
-#default FALLBACK_SIZE=131072
+#default CONFIG_FALLBACK_SIZE=131072
#256K
-default FALLBACK_SIZE=0x40000
+default CONFIG_FALLBACK_SIZE=0x40000
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=11
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=11
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
## ACPI tables will be included
-default HAVE_ACPI_TABLES=1
+default CONFIG_HAVE_ACPI_TABLES=1
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=0
+default CONFIG_HAVE_OPTION_TABLE=0
##
## Move the default coreboot cmos range off of AMD RTC registers
##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
+default CONFIG_LB_CKS_RANGE_START=49
+default CONFIG_LB_CKS_RANGE_END=122
+default CONFIG_LB_CKS_LOC=123
##
## Build code for SMP support
default CONFIG_LOGICAL_CPUS=1
#1G memory hole
-default HW_MEM_HOLE_SIZEK=0x100000
+default CONFIG_HW_MEM_HOLE_SIZEK=0x100000
#VGA Console
default CONFIG_CONSOLE_VGA=1
# BTDC: Only one HT device on Herring.
#HT Unit ID offset
-#default HT_CHAIN_UNITID_BASE=0x6
-default HT_CHAIN_UNITID_BASE=0x0
+#default CONFIG_HT_CHAIN_UNITID_BASE=0x6
+default CONFIG_HT_CHAIN_UNITID_BASE=0x0
#real SB Unit ID
-default HT_CHAIN_END_UNITID_BASE=0x1
+default CONFIG_HT_CHAIN_END_UNITID_BASE=0x1
#make the SB HT chain on bus 0
-default SB_HT_CHAIN_ON_BUS0=1
+default CONFIG_SB_HT_CHAIN_ON_BUS0=1
##
## enable CACHE_AS_RAM specifics
##
-default USE_DCACHE_RAM=1
-default DCACHE_RAM_BASE=0xc8000
-default DCACHE_RAM_SIZE=0x8000
-default DCACHE_RAM_GLOBAL_VAR_SIZE=0x01000
+default CONFIG_USE_DCACHE_RAM=1
+default CONFIG_DCACHE_RAM_BASE=0xc8000
+default CONFIG_DCACHE_RAM_SIZE=0x8000
+default CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE=0x01000
default CONFIG_USE_INIT=0
##
##
## Clean up the motherboard id strings
##
-default MAINBOARD_PART_NUMBER="pistachio"
-default MAINBOARD_VENDOR="amd"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x1022
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x3050
+default CONFIG_MAINBOARD_PART_NUMBER="pistachio"
+default CONFIG_MAINBOARD_VENDOR="amd"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x1022
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x3050
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE=0x4000
+default CONFIG_HEAP_SIZE=0x4000
##
## Only use the option table in a normal image
##
-#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
+#default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 0
##
## coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00004000
+default CONFIG_RAMBASE=0x00004000
##
## Load the payload from the ROM
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## Disable the gdb stub by default
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
default CONFIG_VIDEO_MB=1
default CONFIG_GFXUMA=1
-default HAVE_MAINBOARD_RESOURCES=1
+default CONFIG_HAVE_MAINBOARD_RESOURCES=1
### End Options.lb
#
extern u8 AmlCode[];
-#if ACPI_SSDTX_NUM >= 1
+#if CONFIG_ACPI_SSDTX_NUM >= 1
extern u8 AmlCode_ssdt2[];
extern u8 AmlCode_ssdt3[];
extern u8 AmlCode_ssdt4[];
current += ssdt->length;
acpi_add_table(rsdt, ssdt);
-#if ACPI_SSDTX_NUM >= 1
+#if CONFIG_ACPI_SSDTX_NUM >= 1
/* same htio, but different position? We may have to copy, change HCIN, and recalculate the checknum and add_table */
#include "cpu/amd/model_fxx/fidvid.c"
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
#include "northbridge/amd/amdk8/early_ht.c"
fallback_image:
post_code(0x02);
}
-#endif /* USE_FALLBACK_IMAGE == 1 */
+#endif /* CONFIG_USE_FALLBACK_IMAGE == 1 */
void real_main(unsigned long bist, unsigned long cpu_init_detectedx);
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
failover_process(bist, cpu_init_detectedx);
#endif
real_main(bist, cpu_init_detectedx);
msr_t msr;
struct cpuid_result cpuid1;
struct sys_info *sysinfo =
- (struct sys_info *)(DCACHE_RAM_BASE + DCACHE_RAM_SIZE -
- DCACHE_RAM_GLOBAL_VAR_SIZE);
+ (struct sys_info *)(CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE -
+ CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE);
if (bist == 0) {
bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);
/* PCI interrupts are level triggered, and are
* associated with a specific bus/device/function tuple.
*/
-#if HAVE_ACPI_TABLES == 0
+#if CONFIG_HAVE_ACPI_TABLES == 0
#define PCI_INT(bus, dev, fn, pin) \
smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, (bus), (((dev)<<2)|(fn)), apicid_sb600, (pin))
#else
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
##
driver mainboard.o
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
#object reset.o
##
## Romcc output
##
makerule ./failover.E
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./auto.E
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -E -mcpu=p2 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -E -mcpu=p2 -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -mcpu=p2 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -mcpu=p2 -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
##
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_ROM_PAYLOAD
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses HAVE_MP_TABLE
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
-## ROM_SIZE is the size of boot ROM that this board will use.
-default ROM_SIZE = 256*1024
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
+default CONFIG_ROM_SIZE = 256*1024
###
### Build options
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## no MP table
##
-default HAVE_MP_TABLE=0
+default CONFIG_HAVE_MP_TABLE=0
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=0
+default CONFIG_HAVE_HARD_RESET=0
## Delay timer options
##
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=2
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=2
#object irq_tables.o
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=0
+default CONFIG_HAVE_OPTION_TABLE=0
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
-default FALLBACK_SIZE = 131072
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
+default CONFIG_FALLBACK_SIZE = 131072
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE=0x4000
+default CONFIG_HEAP_SIZE=0x4000
##
## Only use the option table in a normal image
##
-#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
+#default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
##
## The default compiler
##
-default CROSS_COMPILE=""
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CONFIG_CROSS_COMPILE=""
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## The Serial Console
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
#
SystemPreInit();
- w83627hf_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ w83627hf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/failovercalculation.lb
arch i386 end
#needed by irq_tables and mptable and acpi_tables
object get_bus_conf.o
-if HAVE_MP_TABLE
+if CONFIG_HAVE_MP_TABLE
object mptable.o
end
-if HAVE_PIRQ_TABLE
+if CONFIG_HAVE_PIRQ_TABLE
object irq_tables.o
end
-#if HAVE_ACPI_TABLES
+#if CONFIG_HAVE_ACPI_TABLES
# object acpi_tables.o
# object fadt.o
-# if SB_HT_CHAIN_ON_BUS0
+# if CONFIG_SB_HT_CHAIN_ON_BUS0
# object dsdt_bus0.o
# else
# object dsdt.o
# end
# object ssdt.o
-# if ACPI_SSDTX_NUM
-# if SB_HT_CHAIN_ON_BUS0
+# if CONFIG_ACPI_SSDTX_NUM
+# if CONFIG_SB_HT_CHAIN_ON_BUS0
# object ssdt2_bus0.o
# else
# object ssdt2.o
# end
#end
-if HAVE_ACPI_TABLES
+if CONFIG_HAVE_ACPI_TABLES
object acpi_tables.o
object fadt.o
makerule dsdt.c
- depends "$(MAINBOARD)/dx/dsdt_lb.dsl"
- action "iasl -p $(CURDIR)/dsdt_lb -tc $(MAINBOARD)/dx/dsdt_lb.dsl"
+ depends "$(CONFIG_MAINBOARD)/dx/dsdt_lb.dsl"
+ action "iasl -p $(CURDIR)/dsdt_lb -tc $(CONFIG_MAINBOARD)/dx/dsdt_lb.dsl"
action "mv dsdt_lb.hex dsdt.c"
end
object ./dsdt.o
#./ssdt.o is moved to northbridge/amd/amdk8/Config.lb
- if ACPI_SSDTX_NUM
+ if CONFIG_ACPI_SSDTX_NUM
makerule ssdt2.c
- depends "$(MAINBOARD)/dx/pci2.asl"
- action "iasl -p $(CURDIR)/pci2 -tc $(MAINBOARD)/dx/pci2.asl"
+ depends "$(CONFIG_MAINBOARD)/dx/pci2.asl"
+ action "iasl -p $(CURDIR)/pci2 -tc $(CONFIG_MAINBOARD)/dx/pci2.asl"
action "perl -pi -e 's/AmlCode/AmlCode_ssdt2/g' pci2.hex"
action "mv pci2.hex ssdt2.c"
end
object ./ssdt2.o
makerule ssdt3.c
- depends "$(MAINBOARD)/dx/pci3.asl"
- action "iasl -p $(CURDIR)/pci3 -tc $(MAINBOARD)/dx/pci3.asl"
+ depends "$(CONFIG_MAINBOARD)/dx/pci3.asl"
+ action "iasl -p $(CURDIR)/pci3 -tc $(CONFIG_MAINBOARD)/dx/pci3.asl"
action "perl -pi -e 's/AmlCode/AmlCode_ssdt3/g' pci3.hex"
action "mv pci3.hex ssdt3.c"
end
object ./ssdt3.o
makerule ssdt4.c
- depends "$(MAINBOARD)/dx/pci4.asl"
- action "iasl -p $(CURDIR)/pci4 -tc $(MAINBOARD)/dx/pci4.asl"
+ depends "$(CONFIG_MAINBOARD)/dx/pci4.asl"
+ action "iasl -p $(CURDIR)/pci4 -tc $(CONFIG_MAINBOARD)/dx/pci4.asl"
action "perl -pi -e 's/AmlCode/AmlCode_ssdt4/g' pci4.hex"
action "mv pci4.hex ssdt4.c"
end
if CONFIG_USE_INIT
# compile cache_as_ram.c to auto.o
makerule ./cache_as_ram_auto.o
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
end
else
#compile cache_as_ram.c to auto.inc
makerule ./cache_as_ram_auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
end
-if USE_FAILOVER_IMAGE
+if CONFIG_USE_FAILOVER_IMAGE
else
if CONFIG_AP_CODE_IN_CAR
makerule ./apc_auto.o
- depends "$(MAINBOARD)/apc_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/apc_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/apc_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/apc_auto.c -o $@"
end
ldscript /arch/i386/init/ldscript_apc.lb
end
## Build our 16 bit and 32 bit coreboot entry code
##
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
end
##
## Build our reset vector (This is where coreboot is entered)
##
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
ldscript /cpu/x86/32bit/reset32.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
ldscript /arch/i386/lib/failover_failover.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
end
end
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses HAVE_ACPI_TABLES
-uses HAVE_ACPI_RESUME
-uses ACPI_SSDTX_NUM
-uses USE_FALLBACK_IMAGE
-uses USE_FAILOVER_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_FAILOVER_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_HAVE_ACPI_TABLES
+uses CONFIG_HAVE_ACPI_RESUME
+uses CONFIG_ACPI_SSDTX_NUM
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_USE_FAILOVER_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_FAILOVER_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_MAX_CPUS
uses CONFIG_MAX_PHYSICAL_CPUS
uses CONFIG_LOGICAL_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses FAILOVER_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_FAILOVER_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
-uses _RAMBASE
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_RAMBASE
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_SERIAL8250
-uses HAVE_INIT_TIMER
+uses CONFIG_HAVE_INIT_TIMER
uses CONFIG_GDB_STUB
uses CONFIG_GDB_STUB
-uses CROSS_COMPILE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
-uses HW_MEM_HOLE_SIZEK
-uses HW_MEM_HOLE_SIZE_AUTO_INC
-uses K8_HT_FREQ_1G_SUPPORT
-
-uses HT_CHAIN_UNITID_BASE
-uses HT_CHAIN_END_UNITID_BASE
-uses SB_HT_CHAIN_ON_BUS0
-uses SB_HT_CHAIN_UNITID_OFFSET_ONLY
-
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
-uses DCACHE_RAM_GLOBAL_VAR_SIZE
+uses CONFIG_HW_MEM_HOLE_SIZEK
+uses CONFIG_HW_MEM_HOLE_SIZE_AUTO_INC
+uses CONFIG_K8_HT_FREQ_1G_SUPPORT
+
+uses CONFIG_HT_CHAIN_UNITID_BASE
+uses CONFIG_HT_CHAIN_END_UNITID_BASE
+uses CONFIG_SB_HT_CHAIN_ON_BUS0
+uses CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY
+
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
+uses CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE
uses CONFIG_USE_INIT
-uses SERIAL_CPU_INIT
+uses CONFIG_SERIAL_CPU_INIT
-uses ENABLE_APIC_EXT_ID
-uses APIC_ID_OFFSET
-uses LIFT_BSP_APIC_ID
+uses CONFIG_ENABLE_APIC_EXT_ID
+uses CONFIG_APIC_ID_OFFSET
+uses CONFIG_LIFT_BSP_APIC_ID
uses CONFIG_PCI_64BIT_PREF_MEM
uses CONFIG_AP_CODE_IN_CAR
-uses MEM_TRAIN_SEQ
+uses CONFIG_MEM_TRAIN_SEQ
-uses WAIT_BEFORE_CPUS_INIT
+uses CONFIG_WAIT_BEFORE_CPUS_INIT
uses CONFIG_USE_PRINTK_IN_CAR
###
##
-## ROM_SIZE is the size of boot ROM that this board will use.
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
##
-default ROM_SIZE=524288
+default CONFIG_ROM_SIZE=524288
##
-## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
+## CONFIG_FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
##
-#default FALLBACK_SIZE=131072
-#default FALLBACK_SIZE=0x40000
+#default CONFIG_FALLBACK_SIZE=131072
+#default CONFIG_FALLBACK_SIZE=0x40000
#FALLBACK: 256K-4K
-default FALLBACK_SIZE=0x3f000
+default CONFIG_FALLBACK_SIZE=0x3f000
#FAILOVER: 4K
-default FAILOVER_SIZE=0x01000
+default CONFIG_FAILOVER_SIZE=0x01000
#more 1M for pgtbl
default CONFIG_LB_MEM_TOPK=2048
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
-default HAVE_FAILOVER_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FAILOVER_BOOT=1
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=11
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=11
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
## ACPI tables will be included
-default HAVE_ACPI_TABLES=1
+default CONFIG_HAVE_ACPI_TABLES=1
## extra SSDT num
-default ACPI_SSDTX_NUM=1
+default CONFIG_ACPI_SSDTX_NUM=1
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
##
## Move the default coreboot cmos range off of AMD RTC registers
##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
+default CONFIG_LB_CKS_RANGE_START=49
+default CONFIG_LB_CKS_RANGE_END=122
+default CONFIG_LB_CKS_LOC=123
##
## Build code for SMP support
default CONFIG_MAX_PHYSICAL_CPUS=4
default CONFIG_LOGICAL_CPUS=1
-default SERIAL_CPU_INIT=0
+default CONFIG_SERIAL_CPU_INIT=0
-default ENABLE_APIC_EXT_ID=0
-default APIC_ID_OFFSET=0x8
-default LIFT_BSP_APIC_ID=1
+default CONFIG_ENABLE_APIC_EXT_ID=0
+default CONFIG_APIC_ID_OFFSET=0x8
+default CONFIG_LIFT_BSP_APIC_ID=1
#memory hole size, 0 mean disable, others will enable the hole, at that case if it is small than mmio_basek, it will use mmio_basek instead.
#2G
-#default HW_MEM_HOLE_SIZEK=0x200000
+#default CONFIG_HW_MEM_HOLE_SIZEK=0x200000
#1G
-default HW_MEM_HOLE_SIZEK=0x100000
+default CONFIG_HW_MEM_HOLE_SIZEK=0x100000
#512M
-#default HW_MEM_HOLE_SIZEK=0x80000
+#default CONFIG_HW_MEM_HOLE_SIZEK=0x80000
#make auto increase hole size to avoid hole_startk equal to basek so as to make some kernel happy
-#default HW_MEM_HOLE_SIZE_AUTO_INC=1
+#default CONFIG_HW_MEM_HOLE_SIZE_AUTO_INC=1
#Opteron K8 1G HT Support
-default K8_HT_FREQ_1G_SUPPORT=1
+default CONFIG_K8_HT_FREQ_1G_SUPPORT=1
#VGA Console
default CONFIG_CONSOLE_VGA=1
default CONFIG_PCI_ROM_RUN=1
#HT Unit ID offset, default is 1, the typical one
-default HT_CHAIN_UNITID_BASE=0xa
+default CONFIG_HT_CHAIN_UNITID_BASE=0xa
#real SB Unit ID, default is 0x20, mean dont touch it at last
-default HT_CHAIN_END_UNITID_BASE=0x6
+default CONFIG_HT_CHAIN_END_UNITID_BASE=0x6
#make the SB HT chain on bus 0, default is not (0)
-default SB_HT_CHAIN_ON_BUS0=2
+default CONFIG_SB_HT_CHAIN_ON_BUS0=2
#only offset for SB chain?, default is yes(1)
-#default SB_HT_CHAIN_UNITID_OFFSET_ONLY=0
+#default CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY=0
#allow capable device use that above 4G
#default CONFIG_PCI_64BIT_PREF_MEM=1
##
## enable CACHE_AS_RAM specifics
##
-default USE_DCACHE_RAM=1
-default DCACHE_RAM_BASE=0xc8000
-default DCACHE_RAM_SIZE=0x08000
-default DCACHE_RAM_GLOBAL_VAR_SIZE=0x01000
+default CONFIG_USE_DCACHE_RAM=1
+default CONFIG_DCACHE_RAM_BASE=0xc8000
+default CONFIG_DCACHE_RAM_SIZE=0x08000
+default CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE=0x01000
default CONFIG_USE_INIT=0
## for rev F training on AP purpose
##
default CONFIG_AP_CODE_IN_CAR=1
-default MEM_TRAIN_SEQ=1
-default WAIT_BEFORE_CPUS_INIT=1
+default CONFIG_MEM_TRAIN_SEQ=1
+default CONFIG_WAIT_BEFORE_CPUS_INIT=1
##
## Build code to setup a generic IOAPIC
##
## Clean up the motherboard id strings
##
-default MAINBOARD_PART_NUMBER="serengeti_cheetah"
-default MAINBOARD_VENDOR="AMD"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x1022
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2b80
+default CONFIG_MAINBOARD_PART_NUMBER="serengeti_cheetah"
+default CONFIG_MAINBOARD_VENDOR="AMD"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x1022
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2b80
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 32K heap
##
-default HEAP_SIZE=0x8000
+default CONFIG_HEAP_SIZE=0x8000
##
## Only use the option table in a normal image
##
-default USE_OPTION_TABLE = (!USE_FALLBACK_IMAGE) && (!USE_FAILOVER_IMAGE )
+default CONFIG_USE_OPTION_TABLE = (!CONFIG_USE_FALLBACK_IMAGE) && (!CONFIG_USE_FAILOVER_IMAGE )
##
## Coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00100000
+default CONFIG_RAMBASE=0x00100000
##
## Load the payload from the ROM
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## Disable the gdb stub by default
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
### End Options.lb
#
#endif
extern unsigned char AmlCode[];
-#if ACPI_SSDTX_NUM >= 1
+#if CONFIG_ACPI_SSDTX_NUM >= 1
extern unsigned char AmlCode_ssdt2[];
extern unsigned char AmlCode_ssdt3[];
extern unsigned char AmlCode_ssdt4[];
current += ssdt->length;
acpi_add_table(rsdt, ssdt);
-#if ACPI_SSDTX_NUM >= 1
+#if CONFIG_ACPI_SSDTX_NUM >= 1
//same htio, but different position? We may have to copy, change HCIN, and recalculate the checknum and add_table
void hardwaremain(int ret_addr)
{
- struct sys_info *sysinfo = (DCACHE_RAM_BASE + DCACHE_RAM_SIZE - DCACHE_RAM_GLOBAL_VAR_SIZE); // in CACHE
- struct sys_info *sysinfox = ((CONFIG_LB_MEM_TOPK<<10) - DCACHE_RAM_GLOBAL_VAR_SIZE); // in RAM
+ struct sys_info *sysinfo = (CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE); // in CACHE
+ struct sys_info *sysinfox = ((CONFIG_LB_MEM_TOPK<<10) - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE); // in RAM
struct node_core_id id;
//if we want to wait for core1 done before DQS training, set it to 0
#define K8_SET_FIDVID_CORE0_ONLY 1
-#if K8_REV_F_SUPPORT == 1
+#if CONFIG_K8_REV_F_SUPPORT == 1
#define K8_REV_F_SUPPORT_F0_F1_WORKAROUND 0
#endif
#endif
}
#endif
-#if USE_FAILOVER_IMAGE==0
+#if CONFIG_USE_FAILOVER_IMAGE==0
#include "pc80/serial.c"
#include "arch/i386/lib/console.c"
#include <cpu/amd/model_fxx_rev.h>
#include "cpu/x86/lapic/boot_cpu.c"
#include "northbridge/amd/amdk8/reset_test.c"
-#if USE_FAILOVER_IMAGE==0
+#if CONFIG_USE_FAILOVER_IMAGE==0
#include "cpu/x86/bist.h"
#include "lib/delay.c"
#include "cpu/amd/model_fxx/fidvid.c"
#endif
-#if ((HAVE_FAILOVER_BOOT==1) && (USE_FAILOVER_IMAGE == 1)) || ((HAVE_FAILOVER_BOOT==0) && (USE_FALLBACK_IMAGE == 1))
+#if ((CONFIG_HAVE_FAILOVER_BOOT==1) && (CONFIG_USE_FAILOVER_IMAGE == 1)) || ((CONFIG_HAVE_FAILOVER_BOOT==0) && (CONFIG_USE_FALLBACK_IMAGE == 1))
#include "southbridge/amd/amd8111/amd8111_enable_rom.c"
#include "northbridge/amd/amdk8/early_ht.c"
);
fallback_image:
-#if HAVE_FAILOVER_BOOT==1
+#if CONFIG_HAVE_FAILOVER_BOOT==1
__asm__ volatile ("jmp __fallback_image"
: /* outputs */
: "a" (bist), "b" (cpu_init_detectedx) /* inputs */
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
-#if HAVE_FAILOVER_BOOT==1
- #if USE_FAILOVER_IMAGE==1
+#if CONFIG_HAVE_FAILOVER_BOOT==1
+ #if CONFIG_USE_FAILOVER_IMAGE==1
failover_process(bist, cpu_init_detectedx);
#else
real_main(bist, cpu_init_detectedx);
#endif
#else
- #if USE_FALLBACK_IMAGE == 1
+ #if CONFIG_USE_FALLBACK_IMAGE == 1
failover_process(bist, cpu_init_detectedx);
#endif
real_main(bist, cpu_init_detectedx);
#endif
}
-#if USE_FAILOVER_IMAGE==0
+#if CONFIG_USE_FAILOVER_IMAGE==0
void real_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
};
- struct sys_info *sysinfo = (DCACHE_RAM_BASE + DCACHE_RAM_SIZE - DCACHE_RAM_GLOBAL_VAR_SIZE);
+ struct sys_info *sysinfo = (CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE);
int needs_reset; int i;
unsigned bsp_apicid = 0;
// post_code(0x32);
- w83627hf_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ w83627hf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
-// dump_mem(DCACHE_RAM_BASE+DCACHE_RAM_SIZE-0x200, DCACHE_RAM_BASE+DCACHE_RAM_SIZE);
+// dump_mem(CONFIG_DCACHE_RAM_BASE+CONFIG_DCACHE_RAM_SIZE-0x200, CONFIG_DCACHE_RAM_BASE+CONFIG_DCACHE_RAM_SIZE);
/* Halt if there was a built in self test failure */
report_bist_failure(bist);
print_debug("bsp_apicid="); print_debug_hex8(bsp_apicid); print_debug("\r\n");
-#if MEM_TRAIN_SEQ == 1
+#if CONFIG_MEM_TRAIN_SEQ == 1
set_sysinfo_in_ram(0); // in BSP so could hold all ap until sysinfo is in ram
#endif
setup_coherent_ht_domain(); // routing table and start other core0
dev = dev_find_slot(m->bus_8111_0, PCI_DEVFN(sysconf.sbdn,0));
if (dev) {
m->bus_8111_1 = pci_read_config8(dev, PCI_SECONDARY_BUS);
-#if HT_CHAIN_END_UNITID_BASE >= HT_CHAIN_UNITID_BASE
+#if CONFIG_HT_CHAIN_END_UNITID_BASE >= CONFIG_HT_CHAIN_UNITID_BASE
m->bus_isa = pci_read_config8(dev, PCI_SUBORDINATE_BUS);
m->bus_isa++;
// printk_debug("bus_isa=%d\n",bus_isa);
dev = dev_find_slot(m->bus_8132_0, PCI_DEVFN(m->sbdn3+1,0));
if (dev) {
m->bus_8132_2 = pci_read_config8(dev, PCI_SECONDARY_BUS);
-#if HT_CHAIN_END_UNITID_BASE < HT_CHAIN_UNITID_BASE
+#if CONFIG_HT_CHAIN_END_UNITID_BASE < CONFIG_HT_CHAIN_UNITID_BASE
m->bus_isa = pci_read_config8(dev, PCI_SUBORDINATE_BUS);
m->bus_isa++;
// printk_debug("bus_isa=%d\n",bus_isa);
# Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
#
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/failovercalculation.lb
arch i386 end
#needed by irq_tables and mptable and acpi_tables
object get_bus_conf.o
-if HAVE_MP_TABLE
+if CONFIG_HAVE_MP_TABLE
object mptable.o
end
-if HAVE_PIRQ_TABLE
+if CONFIG_HAVE_PIRQ_TABLE
object irq_tables.o
end
-if HAVE_ACPI_TABLES
+if CONFIG_HAVE_ACPI_TABLES
object acpi_tables.o
object fadt.o
makerule dsdt.c
- depends "$(MAINBOARD)/dx/dsdt_lb.dsl"
- action "iasl -p $(CURDIR)/dsdt_lb -tc $(MAINBOARD)/dx/dsdt_lb.dsl"
+ depends "$(CONFIG_MAINBOARD)/dx/dsdt_lb.dsl"
+ action "iasl -p $(CURDIR)/dsdt_lb -tc $(CONFIG_MAINBOARD)/dx/dsdt_lb.dsl"
action "mv dsdt_lb.hex dsdt.c"
end
object ./dsdt.o
#./ssdt.o is moved to northbridge/amd/amdk8/Config.lb
- if ACPI_SSDTX_NUM
+ if CONFIG_ACPI_SSDTX_NUM
makerule ssdt2.c
- depends "$(MAINBOARD)/dx/pci2.asl"
- action "iasl -p $(CURDIR)/pci2 -tc $(MAINBOARD)/dx/pci2.asl"
+ depends "$(CONFIG_MAINBOARD)/dx/pci2.asl"
+ action "iasl -p $(CURDIR)/pci2 -tc $(CONFIG_MAINBOARD)/dx/pci2.asl"
action "perl -pi -e 's/AmlCode/AmlCode_ssdt2/g' pci2.hex"
action "mv pci2.hex ssdt2.c"
end
object ./ssdt2.o
makerule ssdt3.c
- depends "$(MAINBOARD)/dx/pci3.asl"
- action "iasl -p $(CURDIR)/pci3 -tc $(MAINBOARD)/dx/pci3.asl"
+ depends "$(CONFIG_MAINBOARD)/dx/pci3.asl"
+ action "iasl -p $(CURDIR)/pci3 -tc $(CONFIG_MAINBOARD)/dx/pci3.asl"
action "perl -pi -e 's/AmlCode/AmlCode_ssdt3/g' pci3.hex"
action "mv pci3.hex ssdt3.c"
end
object ./ssdt3.o
makerule ssdt4.c
- depends "$(MAINBOARD)/dx/pci4.asl"
- action "iasl -p $(CURDIR)/pci4 -tc $(MAINBOARD)/dx/pci4.asl"
+ depends "$(CONFIG_MAINBOARD)/dx/pci4.asl"
+ action "iasl -p $(CURDIR)/pci4 -tc $(CONFIG_MAINBOARD)/dx/pci4.asl"
action "perl -pi -e 's/AmlCode/AmlCode_ssdt4/g' pci4.hex"
action "mv pci4.hex ssdt4.c"
end
object ./ssdt4.o
makerule ssdt5.c
- depends "$(MAINBOARD)/dx/pci5.asl"
- action "iasl -p $(CURDIR)/pci5 -tc $(MAINBOARD)/dx/pci5.asl"
+ depends "$(CONFIG_MAINBOARD)/dx/pci5.asl"
+ action "iasl -p $(CURDIR)/pci5 -tc $(CONFIG_MAINBOARD)/dx/pci5.asl"
action "perl -pi -e 's/AmlCode/AmlCode_ssdt5/g' pci5.hex"
action "mv pci5.hex ssdt5.c"
end
if CONFIG_USE_INIT
# compile cache_as_ram.c to auto.o
makerule ./cache_as_ram_auto.o
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
end
else
#compile cache_as_ram.c to auto.inc
makerule ./cache_as_ram_auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
end
-if USE_FAILOVER_IMAGE
+if CONFIG_USE_FAILOVER_IMAGE
else
if CONFIG_AP_CODE_IN_CAR
makerule ./apc_auto.o
- depends "$(MAINBOARD)/apc_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/apc_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/apc_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/apc_auto.c -o $@"
end
ldscript /arch/i386/init/ldscript_apc.lb
end
## Build our 16 bit and 32 bit coreboot entry code
##
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
end
##
## Build our reset vector (This is where coreboot is entered)
##
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
ldscript /cpu/x86/32bit/reset32.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
ldscript /arch/i386/lib/failover_failover.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
end
end
# Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
#
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses HAVE_ACPI_TABLES
-uses HAVE_ACPI_RESUME
-uses ACPI_SSDTX_NUM
-uses USE_FALLBACK_IMAGE
-uses USE_FAILOVER_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_FAILOVER_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_HAVE_ACPI_TABLES
+uses CONFIG_HAVE_ACPI_RESUME
+uses CONFIG_ACPI_SSDTX_NUM
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_USE_FAILOVER_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_FAILOVER_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_MAX_CPUS
uses CONFIG_MAX_PHYSICAL_CPUS
uses CONFIG_LOGICAL_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses FAILOVER_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_FAILOVER_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_COMPRESSED_PAYLOAD_NRV2B
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
-uses _RAMBASE
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_RAMBASE
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_SERIAL8250
-uses HAVE_INIT_TIMER
+uses CONFIG_HAVE_INIT_TIMER
uses CONFIG_GDB_STUB
uses CONFIG_GDB_STUB
-uses CROSS_COMPILE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
-uses HW_MEM_HOLE_SIZEK
-uses HW_MEM_HOLE_SIZE_AUTO_INC
-
-uses HT_CHAIN_UNITID_BASE
-uses HT_CHAIN_END_UNITID_BASE
-uses SB_HT_CHAIN_ON_BUS0
-uses SB_HT_CHAIN_UNITID_OFFSET_ONLY
-
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
-uses DCACHE_RAM_GLOBAL_VAR_SIZE
+uses CONFIG_HW_MEM_HOLE_SIZEK
+uses CONFIG_HW_MEM_HOLE_SIZE_AUTO_INC
+
+uses CONFIG_HT_CHAIN_UNITID_BASE
+uses CONFIG_HT_CHAIN_END_UNITID_BASE
+uses CONFIG_SB_HT_CHAIN_ON_BUS0
+uses CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY
+
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
+uses CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE
uses CONFIG_USE_INIT
-uses SERIAL_CPU_INIT
+uses CONFIG_SERIAL_CPU_INIT
-uses ENABLE_APIC_EXT_ID
-uses APIC_ID_OFFSET
-uses LIFT_BSP_APIC_ID
+uses CONFIG_ENABLE_APIC_EXT_ID
+uses CONFIG_APIC_ID_OFFSET
+uses CONFIG_LIFT_BSP_APIC_ID
uses CONFIG_PCI_64BIT_PREF_MEM
uses CONFIG_LB_MEM_TOPK
-uses PCI_BUS_SEGN_BITS
+uses CONFIG_PCI_BUS_SEGN_BITS
uses CONFIG_AP_CODE_IN_CAR
-uses MEM_TRAIN_SEQ
+uses CONFIG_MEM_TRAIN_SEQ
-uses WAIT_BEFORE_CPUS_INIT
+uses CONFIG_WAIT_BEFORE_CPUS_INIT
uses CONFIG_AMDMCT
uses CONFIG_USE_PRINTK_IN_CAR
-uses CAR_FAM10
-uses AMD_UCODE_PATCH_FILE
+uses CONFIG_CAR_FAM10
+uses CONFIG_AMD_UCODE_PATCH_FILE
###
### Build options
###
##
-## ROM_SIZE is the size of boot ROM that this board will use.
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
##
-default ROM_SIZE=1024*1024
+default CONFIG_ROM_SIZE=1024*1024
##
##
#FALLBACK_SIZE_SIZE is the amount of the ROM the complete fallback image will use
##
-#default FALLBACK_SIZE=131072
-#default FALLBACK_SIZE=0x40000
+#default CONFIG_FALLBACK_SIZE=131072
+#default CONFIG_FALLBACK_SIZE=0x40000
#FALLBACK: 1024K - 8K
-default FALLBACK_SIZE=0xFE000
+default CONFIG_FALLBACK_SIZE=0xFE000
#FAILOVER: 8k
-default FAILOVER_SIZE=0x02000
+default CONFIG_FAILOVER_SIZE=0x02000
#more 1M for pgtbl
#if there is RAM on node0, we need to set it to 32M, otherwise can not access CAR on node0, and RAM on node1 at same time.
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
-default HAVE_FAILOVER_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FAILOVER_BOOT=1
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=11
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=11
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
## ACPI tables will be included
-default HAVE_ACPI_TABLES=1
+default CONFIG_HAVE_ACPI_TABLES=1
## extra SSDT num
-default ACPI_SSDTX_NUM=31
+default CONFIG_ACPI_SSDTX_NUM=31
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
##
## Move the default coreboot cmos range off of AMD RTC registers
##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
+default CONFIG_LB_CKS_RANGE_START=49
+default CONFIG_LB_CKS_RANGE_END=122
+default CONFIG_LB_CKS_LOC=123
##
## Build code for SMP support
default CONFIG_MAX_CPUS=6 * CONFIG_MAX_PHYSICAL_CPUS
default CONFIG_LOGICAL_CPUS=1
-#default SERIAL_CPU_INIT=0
+#default CONFIG_SERIAL_CPU_INIT=0
-default ENABLE_APIC_EXT_ID=1
-default APIC_ID_OFFSET=0x00
-default LIFT_BSP_APIC_ID=1
+default CONFIG_ENABLE_APIC_EXT_ID=1
+default CONFIG_APIC_ID_OFFSET=0x00
+default CONFIG_LIFT_BSP_APIC_ID=1
#memory hole size, 0 mean disable, others will enable the hole, at that case if it is small than mmio_basek, it will use mmio_basek instead.
#2G
-#default HW_MEM_HOLE_SIZEK=0x200000
+#default CONFIG_HW_MEM_HOLE_SIZEK=0x200000
#1G
-default HW_MEM_HOLE_SIZEK=0x100000
+default CONFIG_HW_MEM_HOLE_SIZEK=0x100000
#512M
-#default HW_MEM_HOLE_SIZEK=0x80000
+#default CONFIG_HW_MEM_HOLE_SIZEK=0x80000
#make auto increase hole size to avoid hole_startk equal to basek so as to make some kernel happy
-#default HW_MEM_HOLE_SIZE_AUTO_INC=1
+#default CONFIG_HW_MEM_HOLE_SIZE_AUTO_INC=1
#VGA Console
default CONFIG_CONSOLE_VGA=1
default CONFIG_PCI_ROM_RUN=1
#HT Unit ID offset, default is 1, the typical one
-default HT_CHAIN_UNITID_BASE=0xa
+default CONFIG_HT_CHAIN_UNITID_BASE=0xa
#real SB Unit ID, default is 0x20, mean dont touch it at last
-default HT_CHAIN_END_UNITID_BASE=0x6
+default CONFIG_HT_CHAIN_END_UNITID_BASE=0x6
#make the SB HT chain on bus 0, default is not (0)
-default SB_HT_CHAIN_ON_BUS0=2
+default CONFIG_SB_HT_CHAIN_ON_BUS0=2
#only offset for SB chain?, default is yes(1)
-#default SB_HT_CHAIN_UNITID_OFFSET_ONLY=0
+#default CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY=0
#allow capable device use that above 4G
#default CONFIG_PCI_64BIT_PREF_MEM=1
#it only be 0, 1, 2, 3, 4 and default is 0
-#default PCI_BUS_SEGN_BITS=3
+#default CONFIG_PCI_BUS_SEGN_BITS=3
##
## enable CACHE_AS_RAM specifics
##
-default USE_DCACHE_RAM=1
-default DCACHE_RAM_BASE=0xc4000
-default DCACHE_RAM_SIZE=0x0c000
-#default DCACHE_RAM_GLOBAL_VAR_SIZE=0x08000
-default DCACHE_RAM_GLOBAL_VAR_SIZE=0x04000
+default CONFIG_USE_DCACHE_RAM=1
+default CONFIG_DCACHE_RAM_BASE=0xc4000
+default CONFIG_DCACHE_RAM_SIZE=0x0c000
+#default CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE=0x08000
+default CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE=0x04000
default CONFIG_USE_INIT=0
#default CONFIG_AP_CODE_IN_CAR=1
-default MEM_TRAIN_SEQ=2
-default WAIT_BEFORE_CPUS_INIT=0
+default CONFIG_MEM_TRAIN_SEQ=2
+default CONFIG_WAIT_BEFORE_CPUS_INIT=0
default CONFIG_AMDMCT = 1
##
## Clean up the motherboard id strings
##
-default MAINBOARD_PART_NUMBER="Cheetah Fam10"
-default MAINBOARD_VENDOR="AMD"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x1022
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2b80
+default CONFIG_MAINBOARD_PART_NUMBER="Cheetah Fam10"
+default CONFIG_MAINBOARD_VENDOR="AMD"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x1022
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2b80
##
## Set microcode patch file name
## Barcelona rev DR-B2, B3: "mc_patch_01000095.h"
## Shanghai rev DA-C2: "mc_patch_0100009f.h"
##
-default AMD_UCODE_PATCH_FILE="mc_patch_01000095.h"
+default CONFIG_AMD_UCODE_PATCH_FILE="mc_patch_01000095.h"
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 768k heap
##
-default HEAP_SIZE=0xc0000
+default CONFIG_HEAP_SIZE=0xc0000
##
## Only use the option table in a normal image
##
-default USE_OPTION_TABLE = (!USE_FALLBACK_IMAGE) && (!USE_FAILOVER_IMAGE )
+default CONFIG_USE_OPTION_TABLE = (!CONFIG_USE_FALLBACK_IMAGE) && (!CONFIG_USE_FAILOVER_IMAGE )
##
## Coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00200000
+default CONFIG_RAMBASE=0x00200000
##
## Load the payload from the ROM
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## Disable the gdb stub by default
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
### End Options.lb
#
extern u8 AmlCode[];
extern u8 AmlCode_ssdt[];
-#if ACPI_SSDTX_NUM >= 1
+#if CONFIG_ACPI_SSDTX_NUM >= 1
extern u8 AmlCode_ssdt2[];
extern u8 AmlCode_ssdt3[];
extern u8 AmlCode_ssdt4[];
printk_debug("ACPI: * SSDT for PState at %lx\n", current);
current = acpi_add_ssdt_pstates(rsdt, current);
-#if ACPI_SSDTX_NUM >= 1
+#if CONFIG_ACPI_SSDTX_NUM >= 1
/* same htio, but different possition? We may have to copy,
change HCIN, and recalculate the checknum and add_table */
#include "lib/delay.c"
#if NODE_NUMS == 64
- #define NODE_PCI(x,fn) ((x<32)?PCI_DEV(CBB,CDB+x,fn):PCI_DEV(CBB-1, CDB+x-32, fn))
+ #define NODE_PCI(x,fn) ((x<32)?PCI_DEV(CONFIG_CBB,CONFIG_CDB+x,fn):PCI_DEV(CONFIG_CBB-1, CONFIG_CDB+x-32, fn))
#else
- #define NODE_PCI(x, fn) PCI_DEV(CBB,CDB+x,fn)
+ #define NODE_PCI(x, fn) PCI_DEV(CONFIG_CBB,CONFIG_CDB+x,fn)
#endif
//#include "cpu/x86/lapic/boot_cpu.c"
void hardwaremain(int ret_addr)
{
- struct sys_info *sysinfo = (DCACHE_RAM_BASE + DCACHE_RAM_SIZE - DCACHE_RAM_GLOBAL_VAR_SIZE); // in CACHE
- struct sys_info *sysinfox = ((CONFIG_LB_MEM_TOPK<<10) - DCACHE_RAM_GLOBAL_VAR_SIZE); // in RAM
+ struct sys_info *sysinfo = (CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE); // in CACHE
+ struct sys_info *sysinfox = ((CONFIG_LB_MEM_TOPK<<10) - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE); // in RAM
struct node_core_id id;
outb(value, 0x80);
}
-#if (USE_FAILOVER_IMAGE == 0)
+#if (CONFIG_USE_FAILOVER_IMAGE == 0)
#include "arch/i386/lib/console.c"
#include "pc80/serial.c"
#include "ram/ramtest.c"
#include "cpu/x86/bist.h"
-#if (USE_FAILOVER_IMAGE == 0)
+#if (CONFIG_USE_FAILOVER_IMAGE == 0)
#include "northbridge/amd/amdfam10/debug.c"
#include "superio/winbond/w83627hf/w83627hf_early_serial.c"
#include "cpu/amd/model_10xxx/init_cpus.c"
#include "cpu/amd/model_10xxx/fidvid.c"
-#endif /* (USE_FAILOVER_IMAGE == 0) */
+#endif /* (CONFIG_USE_FAILOVER_IMAGE == 0) */
-#if ((HAVE_FAILOVER_BOOT==1) && (USE_FAILOVER_IMAGE == 1)) || ((HAVE_FAILOVER_BOOT==0) && (USE_FALLBACK_IMAGE == 1))
+#if ((CONFIG_HAVE_FAILOVER_BOOT==1) && (CONFIG_USE_FAILOVER_IMAGE == 1)) || ((CONFIG_HAVE_FAILOVER_BOOT==0) && (CONFIG_USE_FALLBACK_IMAGE == 1))
#include "southbridge/amd/amd8111/amd8111_enable_rom.c"
#include "northbridge/amd/amdfam10/early_ht.c"
);
fallback_image:
- #if HAVE_FAILOVER_BOOT==1
+ #if CONFIG_HAVE_FAILOVER_BOOT==1
__asm__ volatile ("jmp __fallback_image"
: /* outputs */
: "a" (bist), "b" (cpu_init_detectedx) /* inputs */
#endif
;
}
-#endif /* ((HAVE_FAILOVER_BOOT==1) && (USE_FAILOVER_IMAGE == 1)) || ((HAVE_FAILOVER_BOOT==0) && (USE_FALLBACK_IMAGE == 1)) */
+#endif /* ((CONFIG_HAVE_FAILOVER_BOOT==1) && (CONFIG_USE_FAILOVER_IMAGE == 1)) || ((CONFIG_HAVE_FAILOVER_BOOT==0) && (CONFIG_USE_FALLBACK_IMAGE == 1)) */
void real_main(unsigned long bist, unsigned long cpu_init_detectedx);
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
-//FIXME: I think that there is a hole here with the real_main() logic realmain is inside a USE_FAILOVER_IMAGE=0.
-#if HAVE_FAILOVER_BOOT==1
- #if USE_FAILOVER_IMAGE==1
+//FIXME: I think that there is a hole here with the real_main() logic realmain is inside a CONFIG_USE_FAILOVER_IMAGE=0.
+#if CONFIG_HAVE_FAILOVER_BOOT==1
+ #if CONFIG_USE_FAILOVER_IMAGE==1
failover_process(bist, cpu_init_detectedx);
#else
real_main(bist, cpu_init_detectedx);
#endif
#else
- #if USE_FALLBACK_IMAGE == 1
+ #if CONFIG_USE_FALLBACK_IMAGE == 1
failover_process(bist, cpu_init_detectedx);
#endif
real_main(bist, cpu_init_detectedx);
}
-#if (USE_FAILOVER_IMAGE==0)
+#if (CONFIG_USE_FAILOVER_IMAGE==0)
#include "spd_addr.h"
#include "cpu/amd/microcode/microcode.c"
#include "cpu/amd/model_10xxx/update_microcode.c"
void real_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
- struct sys_info *sysinfo = (struct sys_info *)(DCACHE_RAM_BASE + DCACHE_RAM_SIZE - DCACHE_RAM_GLOBAL_VAR_SIZE);
+ struct sys_info *sysinfo = (struct sys_info *)(CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE);
u32 bsp_apicid = 0;
u32 val;
msr_t msr;
post_code(0x32);
- w83627hf_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ w83627hf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
printk_debug("\n");
-// dump_mem(DCACHE_RAM_BASE+DCACHE_RAM_SIZE-0x200, DCACHE_RAM_BASE+DCACHE_RAM_SIZE);
+// dump_mem(CONFIG_DCACHE_RAM_BASE+CONFIG_DCACHE_RAM_SIZE-0x200, CONFIG_DCACHE_RAM_BASE+CONFIG_DCACHE_RAM_SIZE);
/* Halt if there was a built in self test failure */
report_bist_failure(bist);
}
-#endif /* USE_FAILOVER_IMAGE==0 */
+#endif /* CONFIG_USE_FAILOVER_IMAGE==0 */
}
-#if CBB
- write_pirq_info(pirq_info, CBB, (0<<3)|0, 0x1, 0xdef8, 0x2, 0xdef8, 0x3, 0xdef8, 0x4, 0xdef8, 0, 0);
+#if CONFIG_CBB
+ write_pirq_info(pirq_info, CONFIG_CBB, (0<<3)|0, 0x1, 0xdef8, 0x2, 0xdef8, 0x3, 0xdef8, 0x4, 0xdef8, 0, 0);
pirq_info++; slot_num++;
if(sysconf.nodes>32) {
- write_pirq_info(pirq_info, CBB-1, (0<<3)|0, 0x1, 0xdef8, 0x2, 0xdef8, 0x3, 0xdef8, 0x4, 0xdef8, 0, 0);
+ write_pirq_info(pirq_info, CONFIG_CBB-1, (0<<3)|0, 0x1, 0xdef8, 0x2, 0xdef8, 0x3, 0xdef8, 0x4, 0xdef8, 0, 0);
pirq_info++; slot_num++;
}
#endif
* This field defines the upper address bits of a 40 bit address
* that define the end of the DRAM region.
*/
-// PCI_ADDR(CBB, CDB, 1, 0x44), 0x0000f8f8, 0x00000000, // Don't touch it, we need it for CAR_FAM10
- PCI_ADDR(CBB, CDB, 1, 0x4C), 0x0000f8f8, 0x00000001,
- PCI_ADDR(CBB, CDB, 1, 0x54), 0x0000f8f8, 0x00000002,
- PCI_ADDR(CBB, CDB, 1, 0x5C), 0x0000f8f8, 0x00000003,
- PCI_ADDR(CBB, CDB, 1, 0x64), 0x0000f8f8, 0x00000004,
- PCI_ADDR(CBB, CDB, 1, 0x6C), 0x0000f8f8, 0x00000005,
- PCI_ADDR(CBB, CDB, 1, 0x74), 0x0000f8f8, 0x00000006,
- PCI_ADDR(CBB, CDB, 1, 0x7C), 0x0000f8f8, 0x00000007,
+// PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x44), 0x0000f8f8, 0x00000000, // Don't touch it, we need it for CONFIG_CAR_FAM10
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x4C), 0x0000f8f8, 0x00000001,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x54), 0x0000f8f8, 0x00000002,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x5C), 0x0000f8f8, 0x00000003,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x64), 0x0000f8f8, 0x00000004,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x6C), 0x0000f8f8, 0x00000005,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x74), 0x0000f8f8, 0x00000006,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x7C), 0x0000f8f8, 0x00000007,
/* DRAM Base i Registers
* F1:0x40 i = 0
* F1:0x48 i = 1
* This field defines the upper address bits of a 40-bit address
* that define the start of the DRAM region.
*/
-// PCI_ADDR(CBB, CDB, 1, 0x40), 0x0000f8fc, 0x00000000,// don't touch it, we need it for CAR_FAM10
- PCI_ADDR(CBB, CDB, 1, 0x48), 0x0000f8fc, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0x50), 0x0000f8fc, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0x58), 0x0000f8fc, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0x60), 0x0000f8fc, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0x68), 0x0000f8fc, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0x70), 0x0000f8fc, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0x78), 0x0000f8fc, 0x00000000,
+// PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x40), 0x0000f8fc, 0x00000000,// don't touch it, we need it for CONFIG_CAR_FAM10
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x48), 0x0000f8fc, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x50), 0x0000f8fc, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x58), 0x0000f8fc, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x60), 0x0000f8fc, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x68), 0x0000f8fc, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x70), 0x0000f8fc, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x78), 0x0000f8fc, 0x00000000,
/* Memory-Mapped I/O Limit i Registers
* F1:0x84 i = 0
* This field defines the upp adddress bits of a 40-bit address that
* defines the end of a memory-mapped I/O region n
*/
- PCI_ADDR(CBB, CDB, 1, 0x84), 0x00000048, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0x8C), 0x00000048, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0x94), 0x00000048, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0x9C), 0x00000048, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0xA4), 0x00000048, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0xAC), 0x00000048, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0xB4), 0x00000048, 0x00000000,
-// PCI_ADDR(CBB, CDB, 1, 0xBC), 0x00000048, 0x00ffff00,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x84), 0x00000048, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x8C), 0x00000048, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x94), 0x00000048, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x9C), 0x00000048, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xA4), 0x00000048, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xAC), 0x00000048, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xB4), 0x00000048, 0x00000000,
+// PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xBC), 0x00000048, 0x00ffff00,
/* Memory-Mapped I/O Base i Registers
* F1:0x80 i = 0
* This field defines the upper address bits of a 40bit address
* that defines the start of memory-mapped I/O region i
*/
- PCI_ADDR(CBB, CDB, 1, 0x80), 0x000000f0, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0x88), 0x000000f0, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0x90), 0x000000f0, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0x98), 0x000000f0, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0xA0), 0x000000f0, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0xA8), 0x000000f0, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0xB0), 0x000000f0, 0x00000000,
-// PCI_ADDR(CBB, CDB, 1, 0xB8), 0x000000f0, 0x00fc0003,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x80), 0x000000f0, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x88), 0x000000f0, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x90), 0x000000f0, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x98), 0x000000f0, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xA0), 0x000000f0, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xA8), 0x000000f0, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xB0), 0x000000f0, 0x00000000,
+// PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xB8), 0x000000f0, 0x00fc0003,
/* PCI I/O Limit i Registers
* F1:0xC4 i = 0
* This field defines the end of PCI I/O region n
* [31:25] Reserved
*/
-// PCI_ADDR(CBB, CDB, 1, 0xC4), 0xFE000FC8, 0x01fff000,
- PCI_ADDR(CBB, CDB, 1, 0xCC), 0xFE000FC8, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0xD4), 0xFE000FC8, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0xDC), 0xFE000FC8, 0x00000000,
+// PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xC4), 0xFE000FC8, 0x01fff000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xCC), 0xFE000FC8, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xD4), 0xFE000FC8, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xDC), 0xFE000FC8, 0x00000000,
/* PCI I/O Base i Registers
* F1:0xC0 i = 0
* This field defines the start of PCI I/O region n
* [31:25] Reserved
*/
-// PCI_ADDR(CBB, CDB, 1, 0xC0), 0xFE000FCC, 0x00000003,
- PCI_ADDR(CBB, CDB, 1, 0xC8), 0xFE000FCC, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0xD0), 0xFE000FCC, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0xD8), 0xFE000FCC, 0x00000000,
+// PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xC0), 0xFE000FCC, 0x00000003,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xC8), 0xFE000FCC, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xD0), 0xFE000FCC, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xD8), 0xFE000FCC, 0x00000000,
/* Config Base and Limit i Registers
* F1:0xE0 i = 0
* [31:24] Bus Number Limit i
* This field defines the highest bus number in configuration regin i
*/
-// PCI_ADDR(CBB, CDB, 1, 0xE0), 0x0000FC88, 0x06000003, // AMD 8111 on link0 of CPU 0
- PCI_ADDR(CBB, CDB, 1, 0xE4), 0x0000FC88, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0xE8), 0x0000FC88, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0xEC), 0x0000FC88, 0x00000000,
+// PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xE0), 0x0000FC88, 0x06000003, // AMD 8111 on link0 of CPU 0
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xE4), 0x0000FC88, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xE8), 0x0000FC88, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xEC), 0x0000FC88, 0x00000000,
};
int max;
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 128 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 128 * 1024
include /config/nofailovercalculation.lb
##
##
driver mainboard.o
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
if CONFIG_USE_INIT
makerule ./auto.o
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
end
else
makerule ./auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
##
## Build our 16 bit and 32 bit coreboot entry code
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
end
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
end
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_MAX_CPUS
uses CONFIG_MAX_PHYSICAL_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
-uses _RAMBASE
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_RAMBASE
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_SERIAL8250
-uses HAVE_INIT_TIMER
+uses CONFIG_HAVE_INIT_TIMER
uses CONFIG_GDB_STUB
-uses CROSS_COMPILE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
uses CONFIG_LOGICAL_CPUS
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
uses CONFIG_USE_INIT
uses CONFIG_USE_PRINTK_IN_CAR
default CONFIG_LOGICAL_CPUS=1
##
-## ROM_SIZE is the size of boot ROM that this board will use.
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
##
-default ROM_SIZE=524288
+default CONFIG_ROM_SIZE=524288
##
-## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
+## CONFIG_FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
##
-default FALLBACK_SIZE=0x40000
+default CONFIG_FALLBACK_SIZE=0x40000
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=9
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=9
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
##
## Move the default coreboot cmos range off of AMD RTC registers
##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
+default CONFIG_LB_CKS_RANGE_START=49
+default CONFIG_LB_CKS_RANGE_END=122
+default CONFIG_LB_CKS_LOC=123
##
## Build code for SMP support
##
## enable CACHE_AS_RAM specifics
##
-default USE_DCACHE_RAM=1
-default DCACHE_RAM_BASE=0xcf000
-default DCACHE_RAM_SIZE=0x1000
+default CONFIG_USE_DCACHE_RAM=1
+default CONFIG_DCACHE_RAM_BASE=0xcf000
+default CONFIG_DCACHE_RAM_SIZE=0x1000
default CONFIG_USE_INIT=0
#VGA
##
## Clean up the motherboard id strings
##
-default MAINBOARD_PART_NUMBER="HDAMA"
-default MAINBOARD_VENDOR="ARIMA"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x161f
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x3016
+default CONFIG_MAINBOARD_PART_NUMBER="HDAMA"
+default CONFIG_MAINBOARD_VENDOR="ARIMA"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x161f
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x3016
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE=0x4000
+default CONFIG_HEAP_SIZE=0x4000
##
## Only use the option table in a normal image
##
-default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
##
## Coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00004000
+default CONFIG_RAMBASE=0x00004000
##
## Load the payload from the ROM
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## Disable the gdb stub by default
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
### End Options.lb
#
#include "cpu/amd/model_fxx/init_cpus.c"
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
#include "southbridge/amd/amd8111/amd8111_enable_rom.c"
#include "northbridge/amd/amdk8/early_ht.c"
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
failover_process(bist, cpu_init_detectedx);
#endif
real_main(bist, cpu_init_detectedx);
init_cpus(cpu_init_detectedx);
}
- pc87360_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ pc87360_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
const struct irq_routing_table intel_irq_routing_table = {
PIRQ_SIGNATURE, /* u32 signature */
PIRQ_VERSION, /* u16 version */
- 32+16*IRQ_SLOT_COUNT, /* there can be total IRQ_SLOT_COUNT table entries */
+ 32+16*CONFIG_IRQ_SLOT_COUNT, /* there can be total CONFIG_IRQ_SLOT_COUNT table entries */
IRQ_ROUTER_BUS, /* Where the interrupt router lies (bus) */
IRQ_ROUTER_DEVFN, /* Where the interrupt router lies (dev) */
0x00, /* IRQs devoted exclusively to PCI usage */
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
##
driver mainboard.o
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
#object reset.o
#compile cache_as_ram.c to auto.inc
makerule ./cache_as_ram_auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
# mainboardinit ./failover.inc
end
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_ROM_PAYLOAD
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_COMPRESSED_PAYLOAD_NRV2B
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses HAVE_MP_TABLE
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
uses CONFIG_VIDEO_MB
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
uses CONFIG_USE_PRINTK_IN_CAR
-uses PIRQ_ROUTE
+uses CONFIG_PIRQ_ROUTE
-## ROM_SIZE is the size of boot ROM that this board will use.
-default ROM_SIZE = 256*1024
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
+default CONFIG_ROM_SIZE = 256*1024
###
### Build options
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## no MP table
##
-default HAVE_MP_TABLE=0
+default CONFIG_HAVE_MP_TABLE=0
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=0
+default CONFIG_HAVE_HARD_RESET=0
## Delay timer options
##
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=3
-default PIRQ_ROUTE=1
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=3
+default CONFIG_PIRQ_ROUTE=1
#object irq_tables.o
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=0
+default CONFIG_HAVE_OPTION_TABLE=0
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
-default FALLBACK_SIZE = 131072
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
+default CONFIG_FALLBACK_SIZE = 131072
##
## enable CACHE_AS_RAM specifics
##
-default USE_DCACHE_RAM=1
-default DCACHE_RAM_BASE=0xc8000
-default DCACHE_RAM_SIZE=0x08000
+default CONFIG_USE_DCACHE_RAM=1
+default CONFIG_DCACHE_RAM_BASE=0xc8000
+default CONFIG_DCACHE_RAM_SIZE=0x08000
default CONFIG_USE_PRINTK_IN_CAR=1
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE=0x4000
+default CONFIG_HEAP_SIZE=0x4000
##
## Only use the option table in a normal image
##
-#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
+#default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
##
## The default compiler
##
-default CROSS_COMPILE=""
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CONFIG_CROSS_COMPILE=""
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## The Serial Console
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
#
const struct irq_routing_table intel_irq_routing_table = {
PIRQ_SIGNATURE, /* u32 signature */
PIRQ_VERSION, /* u16 version */
- 32 + 16 * IRQ_SLOT_COUNT, /* there can be total 6 devices on the bus */
+ 32 + 16 * CONFIG_IRQ_SLOT_COUNT, /* there can be total 6 devices on the bus */
0x00, /* Where the interrupt router lies (bus) */
(0x0F << 3) | 0x0, /* Where the interrupt router lies (dev) */
0x00, /* IRQs devoted exclusively to PCI usage */
{0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0}, /* u8 rfu[11] */
0x00, /* u8 checksum , this has to set to some value that would give 0 after the sum of all bytes for this structure (including checksum) */
{
- /* If you change the number of entries, change the IRQ_SLOT_COUNT above! */
+ /* If you change the number of entries, change the CONFIG_IRQ_SLOT_COUNT above! */
/* bus, dev|fn, {link, bitmap}, {link, bitmap}, {link, bitmap}, {link, bitmap}, slot, rfu */
{0x00, (0x01 << 3) | 0x0, {{L_PIRQA, M_PIRQA}, {0x00, 0x00}, {0x00, 0x00}, {0x00, 0x00}}, 0x0, 0x0}, /* cpu */
{0x00, (0x0F << 3) | 0x0, {{L_PIRQA, M_PIRQA}, {L_PIRQB, M_PIRQB}, {L_PIRQC, M_PIRQC}, {L_PIRQD, M_PIRQD}}, 0x0, 0x0}, /* chipset */
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
arch i386 end
driver mainboard.o
-if HAVE_PIRQ_TABLE
+if CONFIG_HAVE_PIRQ_TABLE
object irq_tables.o
end
makerule ./failover.E
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./auto.E
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -E -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -E -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
mainboardinit cpu/x86/16bit/entry16.inc
mainboardinit cpu/x86/32bit/entry32.inc
ldscript /cpu/x86/16bit/entry16.lds
ldscript /cpu/x86/32bit/entry32.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
mainboardinit arch/i386/lib/cpu_reset.inc
mainboardinit arch/i386/lib/id.inc
ldscript /arch/i386/lib/id.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_ROM_PAYLOAD
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
uses CONFIG_SPLASH_GRAPHIC
uses CONFIG_GX1_VIDEO
uses CONFIG_GX1_VIDEOMODE
-uses PIRQ_ROUTE
+uses CONFIG_PIRQ_ROUTE
## Enable VGA with a splash screen (only 640x480 to run on most monitors).
## We want to support up to 1024x768@16 so we need 2MiB video memory.
default CONFIG_SPLASH_GRAPHIC = 1
default CONFIG_VIDEO_MB = 2
-default ROM_SIZE = 256 * 1024
-default HAVE_PIRQ_TABLE = 1
-default IRQ_SLOT_COUNT = 0 # Override this in targets/*/Config.lb.
-default PIRQ_ROUTE = 1
-default HAVE_FALLBACK_BOOT = 1
-default HAVE_MP_TABLE = 0
-default HAVE_HARD_RESET = 0
+default CONFIG_ROM_SIZE = 256 * 1024
+default CONFIG_HAVE_PIRQ_TABLE = 1
+default CONFIG_IRQ_SLOT_COUNT = 0 # Override this in targets/*/Config.lb.
+default CONFIG_PIRQ_ROUTE = 1
+default CONFIG_HAVE_FALLBACK_BOOT = 1
+default CONFIG_HAVE_MP_TABLE = 0
+default CONFIG_HAVE_HARD_RESET = 0
default CONFIG_UDELAY_TSC = 1
default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 1
-default HAVE_OPTION_TABLE = 0
-default MAINBOARD_VENDOR = "N/A" # Override this in targets/*/Config.lb.
-default MAINBOARD_PART_NUMBER = "N/A" # Override this in targets/*/Config.lb.
-default ROM_IMAGE_SIZE = 64 * 1024
-default FALLBACK_SIZE = 128 * 1024
-default STACK_SIZE = 8 * 1024
-default HEAP_SIZE = 16 * 1024
-default USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_HAVE_OPTION_TABLE = 0
+default CONFIG_MAINBOARD_VENDOR = "N/A" # Override this in targets/*/Config.lb.
+default CONFIG_MAINBOARD_PART_NUMBER = "N/A" # Override this in targets/*/Config.lb.
+default CONFIG_ROM_IMAGE_SIZE = 64 * 1024
+default CONFIG_FALLBACK_SIZE = 128 * 1024
+default CONFIG_STACK_SIZE = 8 * 1024
+default CONFIG_HEAP_SIZE = 16 * 1024
+default CONFIG_USE_OPTION_TABLE = 0
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
-default CROSS_COMPILE = ""
-default CC = "$(CROSS_COMPILE)gcc "
-default HOSTCC = "gcc"
+default CONFIG_CROSS_COMPILE = ""
+default CC = "$(CONFIG_CROSS_COMPILE)gcc "
+default CONFIG_HOSTCC = "gcc"
default CONFIG_CONSOLE_SERIAL8250 = 1
-default TTYS0_BAUD = 115200
-default TTYS0_BASE = 0x3f8
-default TTYS0_LCS = 0x3 # 8n1
-default DEFAULT_CONSOLE_LOGLEVEL = 9
-default MAXIMUM_CONSOLE_LOGLEVEL = 9
+default CONFIG_TTYS0_BAUD = 115200
+default CONFIG_TTYS0_BASE = 0x3f8
+default CONFIG_TTYS0_LCS = 0x3 # 8n1
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
#
# CBFS
static void main(unsigned long bist)
{
- pc87351_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ pc87351_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
report_bist_failure(bist);
const struct irq_routing_table intel_irq_routing_table = {
PIRQ_SIGNATURE,
PIRQ_VERSION,
- 32 + 16 * IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
+ 32 + 16 * CONFIG_IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
0x00, /* Interrupt router bus */
(0x12 << 3) | 0x0, /* Interrupt router device */
0x8800, /* IRQs devoted exclusively to PCI usage */
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
##
driver mainboard.o
-if HAVE_PIRQ_TABLE
+if CONFIG_HAVE_PIRQ_TABLE
object irq_tables.o
end
## Romcc output
##
# makerule ./failover.E
-# depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
-# action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+# depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+# action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
# end
#
# makerule ./failover.inc
-# depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
-# action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+# depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+# action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
# end
makerule ./auto.E
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -E -mcpu=i386 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -E -mcpu=i386 -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -mcpu=i386 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -mcpu=i386 -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
##
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-# if USE_FALLBACK_IMAGE
+# if CONFIG_USE_FALLBACK_IMAGE
# ldscript /arch/i386/lib/failover.lds
# mainboardinit ./failover.inc
# end
-uses HAVE_PIRQ_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
uses CONFIG_CBFS
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
uses CONFIG_ROM_PAYLOAD
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESS
uses CONFIG_COMPRESSED_PAYLOAD_NRV2B
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
# uses CONFIG_CONSOLE_VGA
# uses CONFIG_PCI_ROM_RUN
uses CONFIG_VIDEO_MB
-uses PIRQ_ROUTE
+uses CONFIG_PIRQ_ROUTE
-## ROM_SIZE is the size of boot ROM that this board will use.
-default ROM_SIZE = 256 * 1024
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
+default CONFIG_ROM_SIZE = 256 * 1024
###
### Build options
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=0
+default CONFIG_HAVE_HARD_RESET=0
## Delay timer options
##
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=5 # TODO?
-default PIRQ_ROUTE=1
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=5 # TODO?
+default CONFIG_PIRQ_ROUTE=1
##
## Build code to export a CMOS option table
##
-# default HAVE_OPTION_TABLE=0
+# default CONFIG_HAVE_OPTION_TABLE=0
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 64 * 1024
-default FALLBACK_SIZE = 128 * 1024
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 64 * 1024
+default CONFIG_FALLBACK_SIZE = 128 * 1024
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE=0x4000
+default CONFIG_HEAP_SIZE=0x4000
##
## Only use the option table in a normal image
##
-#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-# default USE_OPTION_TABLE = 0
+#default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+# default CONFIG_USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
##
## The default compiler
##
-default CROSS_COMPILE=""
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CONFIG_CROSS_COMPILE=""
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## The Serial Console
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=9
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=9
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=9
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=9
# VGA Console
# default CONFIG_CONSOLE_VGA=1
static void main(unsigned long bist)
{
/* Initialize the serial console. */
- pc87351_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ pc87351_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/failovercalculation.lb
arch i386 end
driver mainboard.o
# Needed by irq_tables and mptable and acpi_tables.
object get_bus_conf.o
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
if CONFIG_USE_INIT
makerule ./auto.o
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
end
else
makerule ./auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
end
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
end
ldscript /cpu/x86/32bit/entry32.lds
ldscript /cpu/amd/car/cache_as_ram.lds
end
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
ldscript /cpu/x86/32bit/reset32.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
mainboardinit southbridge/nvidia/ck804/id.inc
ldscript /southbridge/nvidia/ck804/id.lds
# ROMSTRAP table for CK804.
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
mainboardinit southbridge/nvidia/ck804/romstrap.inc
ldscript /southbridge/nvidia/ck804/romstrap.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
mainboardinit southbridge/nvidia/ck804/romstrap.inc
ldscript /southbridge/nvidia/ck804/romstrap.lds
end
end
mainboardinit cpu/amd/car/cache_as_ram.inc
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
ldscript /arch/i386/lib/failover_failover.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
end
end
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses USE_FAILOVER_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_FAILOVER_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_USE_FAILOVER_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_FAILOVER_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_MAX_CPUS
uses CONFIG_MAX_PHYSICAL_CPUS
uses CONFIG_LOGICAL_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses FAILOVER_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_FAILOVER_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
-uses _RAMBASE
+uses CONFIG_RAMBASE
uses CONFIG_GDB_STUB
-uses CROSS_COMPILE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_SERIAL8250
uses CONFIG_CONSOLE_BTEXT
-uses HAVE_INIT_TIMER
+uses CONFIG_HAVE_INIT_TIMER
uses CONFIG_GDB_STUB
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
-uses HW_MEM_HOLE_SIZEK
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
+uses CONFIG_HW_MEM_HOLE_SIZEK
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
uses CONFIG_USE_INIT
-uses DCACHE_RAM_GLOBAL_VAR_SIZE
+uses CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE
uses CONFIG_AP_CODE_IN_CAR
-uses MEM_TRAIN_SEQ
-uses WAIT_BEFORE_CPUS_INIT
-uses ENABLE_APIC_EXT_ID
-uses APIC_ID_OFFSET
-uses LIFT_BSP_APIC_ID
+uses CONFIG_MEM_TRAIN_SEQ
+uses CONFIG_WAIT_BEFORE_CPUS_INIT
+uses CONFIG_ENABLE_APIC_EXT_ID
+uses CONFIG_APIC_ID_OFFSET
+uses CONFIG_LIFT_BSP_APIC_ID
uses CONFIG_PCI_64BIT_PREF_MEM
-uses HT_CHAIN_UNITID_BASE
-uses HT_CHAIN_END_UNITID_BASE
-uses SB_HT_CHAIN_ON_BUS0
-uses SB_HT_CHAIN_UNITID_OFFSET_ONLY
+uses CONFIG_HT_CHAIN_UNITID_BASE
+uses CONFIG_HT_CHAIN_END_UNITID_BASE
+uses CONFIG_SB_HT_CHAIN_ON_BUS0
+uses CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY
uses CONFIG_LB_MEM_TOPK
uses CONFIG_USE_PRINTK_IN_CAR
-default ROM_SIZE = 512 * 1024
-default ROM_IMAGE_SIZE = 64 * 1024
-default FALLBACK_SIZE = 252 * 1024
-default FAILOVER_SIZE = 4 * 1024
-default HAVE_FALLBACK_BOOT = 1
-default HAVE_FAILOVER_BOOT = 1
-default HAVE_HARD_RESET = 1
-default HAVE_PIRQ_TABLE = 1
-default IRQ_SLOT_COUNT = 13
-default HAVE_MP_TABLE = 1
-default HAVE_OPTION_TABLE = 1
+default CONFIG_ROM_SIZE = 512 * 1024
+default CONFIG_ROM_IMAGE_SIZE = 64 * 1024
+default CONFIG_FALLBACK_SIZE = 252 * 1024
+default CONFIG_FAILOVER_SIZE = 4 * 1024
+default CONFIG_HAVE_FALLBACK_BOOT = 1
+default CONFIG_HAVE_FAILOVER_BOOT = 1
+default CONFIG_HAVE_HARD_RESET = 1
+default CONFIG_HAVE_PIRQ_TABLE = 1
+default CONFIG_IRQ_SLOT_COUNT = 13
+default CONFIG_HAVE_MP_TABLE = 1
+default CONFIG_HAVE_OPTION_TABLE = 1
# Move the default coreboot CMOS range off of AMD RTC registers.
-default LB_CKS_RANGE_START = 49
-default LB_CKS_RANGE_END = 122
-default LB_CKS_LOC = 123
+default CONFIG_LB_CKS_RANGE_START = 49
+default CONFIG_LB_CKS_RANGE_END = 122
+default CONFIG_LB_CKS_LOC = 123
# SMP support (only worry about 2 micro processors).
default CONFIG_SMP = 1
default CONFIG_MAX_CPUS = 2
default CONFIG_MAX_PHYSICAL_CPUS = 1
default CONFIG_LOGICAL_CPUS = 1
# 1G memory hole.
-default HW_MEM_HOLE_SIZEK = 0x100000
+default CONFIG_HW_MEM_HOLE_SIZEK = 0x100000
# HT Unit ID offset, default is 1, the typical one.
-default HT_CHAIN_UNITID_BASE = 0
+default CONFIG_HT_CHAIN_UNITID_BASE = 0
# Real SB Unit ID, default is 0x20, mean don't touch it at last.
-# default HT_CHAIN_END_UNITID_BASE = 0x10
+# default CONFIG_HT_CHAIN_END_UNITID_BASE = 0x10
# Make the SB HT chain on bus 0, default is not (0).
-default SB_HT_CHAIN_ON_BUS0 = 2
+default CONFIG_SB_HT_CHAIN_ON_BUS0 = 2
# Only offset for SB chain?, default is yes(1).
-default SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0
+default CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0
# default CONFIG_CONSOLE_BTEXT = 1 # BTEXT console
default CONFIG_CONSOLE_VGA = 1 # For VGA console
default CONFIG_PCI_ROM_RUN = 1 # For VGA console
-default USE_DCACHE_RAM = 1
-default DCACHE_RAM_BASE = 0xc8000
-default DCACHE_RAM_SIZE = 32 * 1024
-default DCACHE_RAM_GLOBAL_VAR_SIZE = 4 * 1024
+default CONFIG_USE_DCACHE_RAM = 1
+default CONFIG_DCACHE_RAM_BASE = 0xc8000
+default CONFIG_DCACHE_RAM_SIZE = 32 * 1024
+default CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE = 4 * 1024
default CONFIG_USE_INIT = 0
default CONFIG_AP_CODE_IN_CAR = 0
-default MEM_TRAIN_SEQ = 2
-default WAIT_BEFORE_CPUS_INIT = 0
-# default ENABLE_APIC_EXT_ID = 0
-# default APIC_ID_OFFSET = 0x10
-# default LIFT_BSP_APIC_ID = 0
+default CONFIG_MEM_TRAIN_SEQ = 2
+default CONFIG_WAIT_BEFORE_CPUS_INIT = 0
+# default CONFIG_ENABLE_APIC_EXT_ID = 0
+# default CONFIG_APIC_ID_OFFSET = 0x10
+# default CONFIG_LIFT_BSP_APIC_ID = 0
# default CONFIG_PCI_64BIT_PREF_MEM = 1
default CONFIG_IOAPIC = 1
-default MAINBOARD_PART_NUMBER = "A8N-E"
-default MAINBOARD_VENDOR = "ASUS"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID = 0x1043
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID = 0x815a
-default STACK_SIZE = 8 * 1024
-default HEAP_SIZE = 16 * 1024
+default CONFIG_MAINBOARD_PART_NUMBER = "A8N-E"
+default CONFIG_MAINBOARD_VENDOR = "ASUS"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID = 0x1043
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID = 0x815a
+default CONFIG_STACK_SIZE = 8 * 1024
+default CONFIG_HEAP_SIZE = 16 * 1024
# Only use the option table in a normal image.
-default USE_OPTION_TABLE = (!USE_FALLBACK_IMAGE) && (!USE_FAILOVER_IMAGE)
-default _RAMBASE = 0x00004000
+default CONFIG_USE_OPTION_TABLE = (!CONFIG_USE_FALLBACK_IMAGE) && (!CONFIG_USE_FAILOVER_IMAGE)
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
-default CC = "$(CROSS_COMPILE)gcc -m32"
-default HOSTCC = "gcc"
+default CC = "$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC = "gcc"
default CONFIG_GDB_STUB = 0
default CONFIG_USE_PRINTK_IN_CAR=1
default CONFIG_CONSOLE_SERIAL8250 = 1
-default TTYS0_BAUD = 115200
-default TTYS0_BASE = 0x3f8
-default TTYS0_LCS = 0x3
-default DEFAULT_CONSOLE_LOGLEVEL = 8
-default MAXIMUM_CONSOLE_LOGLEVEL = 8
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL = "MAINBOARD_POWER_ON"
+default CONFIG_TTYS0_BAUD = 115200
+default CONFIG_TTYS0_BASE = 0x3f8
+default CONFIG_TTYS0_LCS = 0x3
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 8
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL = "MAINBOARD_POWER_ON"
#
# CBFS
#include "northbridge/amd/amdk8/reset_test.c"
#include "superio/ite/it8712f/it8712f_early_serial.c"
-#if USE_FAILOVER_IMAGE == 0
+#if CONFIG_USE_FAILOVER_IMAGE == 0
/* Used by ck894_early_setup(). */
#define CK804_NUM 1
#include "cpu/amd/car/post_cache_as_ram.c"
#include "cpu/amd/model_fxx/init_cpus.c"
-#endif /* USE_FAILOVER_IMAGE */
+#endif /* CONFIG_USE_FAILOVER_IMAGE */
-#if ((HAVE_FAILOVER_BOOT==1) && (USE_FAILOVER_IMAGE == 1)) \
- || ((HAVE_FAILOVER_BOOT==0) && (USE_FALLBACK_IMAGE == 1))
+#if ((CONFIG_HAVE_FAILOVER_BOOT==1) && (CONFIG_USE_FAILOVER_IMAGE == 1)) \
+ || ((CONFIG_HAVE_FAILOVER_BOOT==0) && (CONFIG_USE_FALLBACK_IMAGE == 1))
#include "southbridge/nvidia/ck804/ck804_enable_rom.c"
#include "northbridge/amd/amdk8/early_ht.c"
fallback_image:
-#if HAVE_FAILOVER_BOOT == 1
+#if CONFIG_HAVE_FAILOVER_BOOT == 1
__asm__ volatile ("jmp __fallback_image"
: /* outputs */
:"a" (bist), "b"(cpu_init_detectedx) /* inputs */
;
}
-#endif /* ((HAVE_FAILOVER_BOOT==1) && (USE_FAILOVER_IMAGE == 1)) ... */
+#endif /* ((CONFIG_HAVE_FAILOVER_BOOT==1) && (CONFIG_USE_FAILOVER_IMAGE == 1)) ... */
void real_main(unsigned long bist, unsigned long cpu_init_detectedx);
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
-#if HAVE_FAILOVER_BOOT == 1
-#if USE_FAILOVER_IMAGE == 1
+#if CONFIG_HAVE_FAILOVER_BOOT == 1
+#if CONFIG_USE_FAILOVER_IMAGE == 1
failover_process(bist, cpu_init_detectedx);
#else
real_main(bist, cpu_init_detectedx);
#endif
#else
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
failover_process(bist, cpu_init_detectedx);
#endif
real_main(bist, cpu_init_detectedx);
#endif
}
-#if USE_FAILOVER_IMAGE == 0
+#if CONFIG_USE_FAILOVER_IMAGE == 0
void real_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
static const uint16_t spd_addr[] = {
bsp_apicid = init_cpus(cpu_init_detectedx);
it8712f_24mhz_clkin();
- it8712f_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ it8712f_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
post_cache_as_ram();
}
-#endif /* USE_FAILOVER_IMAGE */
+#endif /* CONFIG_USE_FAILOVER_IMAGE */
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
default CONFIG_ROM_PAYLOAD = 1
arch i386 end
driver mainboard.o
-if HAVE_ACPI_TABLES
+if CONFIG_HAVE_ACPI_TABLES
object acpi_tables.o
makerule dsdt.c
- depends "$(MAINBOARD)/dsdt.asl"
- action "iasl -p $(CURDIR)/dsdt -tc $(MAINBOARD)/dsdt.asl"
+ depends "$(CONFIG_MAINBOARD)/dsdt.asl"
+ action "iasl -p $(CURDIR)/dsdt -tc $(CONFIG_MAINBOARD)/dsdt.asl"
action "mv dsdt.hex dsdt.c"
end
object ./dsdt.o
end
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
# object reset.o
if CONFIG_USE_INIT
makerule ./cache_as_ram_auto.o
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
end
else
makerule ./cache_as_ram_auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
end
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
mainboardinit southbridge/via/k8t890/romstrap.inc
ldscript /cpu/amd/car/cache_as_ram.lds
end
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
mainboardinit cpu/amd/car/cache_as_ram.inc
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
end
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_MAX_CPUS
uses CONFIG_MAX_PHYSICAL_CPUS
uses CONFIG_LOGICAL_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-# uses USE_OPTION_TABLE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+# uses CONFIG_USE_OPTION_TABLE
# uses CONFIG_LB_MEM_TOPK
-uses HAVE_ACPI_TABLES
-uses HAVE_ACPI_RESUME
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_HAVE_ACPI_TABLES
+uses CONFIG_HAVE_ACPI_RESUME
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
-uses _RAMBASE
+uses CONFIG_RAMBASE
uses CONFIG_GDB_STUB
-uses CROSS_COMPILE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_SERIAL8250
-uses HAVE_INIT_TIMER
+uses CONFIG_HAVE_INIT_TIMER
uses CONFIG_GDB_STUB
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
# bx_b001- uses K8_HW_MEM_HOLE_SIZEK
-uses K8_HT_FREQ_1G_SUPPORT
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
-uses DCACHE_RAM_GLOBAL_VAR_SIZE
+uses CONFIG_K8_HT_FREQ_1G_SUPPORT
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
+uses CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE
uses CONFIG_USE_INIT
-uses ENABLE_APIC_EXT_ID
-uses APIC_ID_OFFSET
-uses LIFT_BSP_APIC_ID
-uses HT_CHAIN_UNITID_BASE
-uses HT_CHAIN_END_UNITID_BASE
+uses CONFIG_ENABLE_APIC_EXT_ID
+uses CONFIG_APIC_ID_OFFSET
+uses CONFIG_LIFT_BSP_APIC_ID
+uses CONFIG_HT_CHAIN_UNITID_BASE
+uses CONFIG_HT_CHAIN_END_UNITID_BASE
# bx_b001- uses K8_SB_HT_CHAIN_ON_BUS0
-uses SB_HT_CHAIN_UNITID_OFFSET_ONLY
+uses CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY
# bx_b005+
-uses SB_HT_CHAIN_ON_BUS0
+uses CONFIG_SB_HT_CHAIN_ON_BUS0
uses CONFIG_COMPRESSED_PAYLOAD_NRV2B
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_USE_PRINTK_IN_CAR
-default ROM_SIZE = 512 * 1024
-default FALLBACK_SIZE = 256 * 1024
-default HAVE_FALLBACK_BOOT = 1
-default HAVE_HARD_RESET = 0
-default HAVE_PIRQ_TABLE = 0
-default IRQ_SLOT_COUNT = 11 # FIXME?
-default HAVE_MP_TABLE = 1
-default HAVE_OPTION_TABLE = 0 # FIXME
+default CONFIG_ROM_SIZE = 512 * 1024
+default CONFIG_FALLBACK_SIZE = 256 * 1024
+default CONFIG_HAVE_FALLBACK_BOOT = 1
+default CONFIG_HAVE_HARD_RESET = 0
+default CONFIG_HAVE_PIRQ_TABLE = 0
+default CONFIG_IRQ_SLOT_COUNT = 11 # FIXME?
+default CONFIG_HAVE_MP_TABLE = 1
+default CONFIG_HAVE_OPTION_TABLE = 0 # FIXME
# Move the default coreboot CMOS range off of AMD RTC registers.
-default LB_CKS_RANGE_START = 49
-default LB_CKS_RANGE_END = 122
-default LB_CKS_LOC = 123
+default CONFIG_LB_CKS_RANGE_START = 49
+default CONFIG_LB_CKS_RANGE_END = 122
+default CONFIG_LB_CKS_LOC = 123
default CONFIG_SMP = 1
default CONFIG_MAX_CPUS = 2
default CONFIG_MAX_PHYSICAL_CPUS = 1
default CONFIG_LOGICAL_CPUS = 1
-default HAVE_ACPI_TABLES = 1
+default CONFIG_HAVE_ACPI_TABLES = 1
# 1G memory hole
# bx_b001- default K8_HW_MEM_HOLE_SIZEK = 0x100000
# Opteron K8 1G HT support
-default K8_HT_FREQ_1G_SUPPORT = 1
+default CONFIG_K8_HT_FREQ_1G_SUPPORT = 1
# HT Unit ID offset, default is 1, the typical one.
-default HT_CHAIN_UNITID_BASE = 0x0
+default CONFIG_HT_CHAIN_UNITID_BASE = 0x0
# Real SB Unit ID, default is 0x20, mean don't touch it at last.
-# default HT_CHAIN_END_UNITID_BASE = 0x0
+# default CONFIG_HT_CHAIN_END_UNITID_BASE = 0x0
# Make the SB HT chain on bus 0, default is not (0).
# bx_b001- default K8_SB_HT_CHAIN_ON_BUS0 = 2
# bx_b005+ make the SB HT chain on bus 0.
-default SB_HT_CHAIN_ON_BUS0 = 1
+default CONFIG_SB_HT_CHAIN_ON_BUS0 = 1
# Only offset for SB chain?, default is yes(1).
-default SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0
+default CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0
default CONFIG_CONSOLE_VGA = 1 # Needed for VGA.
default CONFIG_PCI_ROM_RUN = 1 # Needed for VGA.
-default USE_DCACHE_RAM = 1
-default DCACHE_RAM_BASE = 0xcc000
-default DCACHE_RAM_SIZE = 0x4000
-default DCACHE_RAM_GLOBAL_VAR_SIZE = 0x01000
+default CONFIG_USE_DCACHE_RAM = 1
+default CONFIG_DCACHE_RAM_BASE = 0xcc000
+default CONFIG_DCACHE_RAM_SIZE = 0x4000
+default CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE = 0x01000
default CONFIG_USE_INIT = 0
-default ENABLE_APIC_EXT_ID = 0
-default APIC_ID_OFFSET = 0x10
-default LIFT_BSP_APIC_ID = 0
+default CONFIG_ENABLE_APIC_EXT_ID = 0
+default CONFIG_APIC_ID_OFFSET = 0x10
+default CONFIG_LIFT_BSP_APIC_ID = 0
default CONFIG_IOAPIC = 1
-default MAINBOARD_VENDOR = "ASUS"
-default MAINBOARD_PART_NUMBER = "A8V-E SE"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID = 0x1043
-# default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID = 0x1234 # FIXME
-default ROM_IMAGE_SIZE = 64 * 1024
-default STACK_SIZE = 8 * 1024
-default HEAP_SIZE = 256 * 1024
+default CONFIG_MAINBOARD_VENDOR = "ASUS"
+default CONFIG_MAINBOARD_PART_NUMBER = "A8V-E SE"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID = 0x1043
+# default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID = 0x1234 # FIXME
+default CONFIG_ROM_IMAGE_SIZE = 64 * 1024
+default CONFIG_STACK_SIZE = 8 * 1024
+default CONFIG_HEAP_SIZE = 256 * 1024
# More 1M for pgtbl.
# default CONFIG_LB_MEM_TOPK = 2048
-default _RAMBASE = 0x00004000
-# default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
+default CONFIG_RAMBASE = 0x00004000
+# default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
default CONFIG_ROM_PAYLOAD = 1
-default CC = "$(CROSS_COMPILE)gcc -m32"
-default HOSTCC = "gcc"
+default CC = "$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC = "gcc"
default CONFIG_GDB_STUB = 0
default CONFIG_USE_PRINTK_IN_CAR = 1
default CONFIG_CONSOLE_SERIAL8250 = 1
-default TTYS0_BAUD = 115200
-default TTYS0_BASE = 0x3f8
-default TTYS0_LCS = 0x3 # 8n1
-default DEFAULT_CONSOLE_LOGLEVEL = 8
-default MAXIMUM_CONSOLE_LOGLEVEL = 8
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL = "MAINBOARD_POWER_ON"
+default CONFIG_TTYS0_BAUD = 115200
+default CONFIG_TTYS0_BASE = 0x3f8
+default CONFIG_TTYS0_LCS = 0x3 # 8n1
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 8
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL = "MAINBOARD_POWER_ON"
#
# CBFS
#
pnp_exit_ext_func_mode(GPIO_DEV);
}
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
void failover_process(unsigned long bist, unsigned long cpu_init_detectedx)
{
unsigned last_boot_normal_x = 1;
sio_init();
- w83627ehg_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ w83627ehg_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
enable_rom_decode();
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
failover_process(bist, cpu_init_detectedx);
#endif
real_main(bist, cpu_init_detectedx);
unsigned bsp_apicid = 0;
int needs_reset = 0;
struct sys_info *sysinfo =
- (DCACHE_RAM_BASE + DCACHE_RAM_SIZE - DCACHE_RAM_GLOBAL_VAR_SIZE);
+ (CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE);
char *p;
sio_init();
- w83627ehg_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ w83627ehg_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
enable_rom_decode();
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 128 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 128 * 1024
include /config/nofailovercalculation.lb
arch i386 end
driver mainboard.o
-if HAVE_ACPI_TABLES
+if CONFIG_HAVE_ACPI_TABLES
object acpi_tables.o
makerule dsdt.c
- depends "$(MAINBOARD)/dsdt.asl"
- action "iasl -p $(CURDIR)/dsdt -tc $(MAINBOARD)/dsdt.asl"
+ depends "$(CONFIG_MAINBOARD)/dsdt.asl"
+ action "iasl -p $(CURDIR)/dsdt -tc $(CONFIG_MAINBOARD)/dsdt.asl"
action "mv dsdt.hex dsdt.c"
end
object ./dsdt.o
if CONFIG_USE_INIT
makerule ./cache_as_ram_auto.o
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
end
else
makerule ./cache_as_ram_auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
end
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
mainboardinit southbridge/via/k8t890/romstrap.inc
ldscript /cpu/amd/car/cache_as_ram.lds
end
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
mainboardinit cpu/amd/car/cache_as_ram.inc
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
end
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_MAX_CPUS
uses CONFIG_MAX_PHYSICAL_CPUS
uses CONFIG_LOGICAL_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-# uses USE_OPTION_TABLE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+# uses CONFIG_USE_OPTION_TABLE
uses CONFIG_LB_MEM_TOPK
-uses HAVE_ACPI_TABLES
-uses HAVE_MAINBOARD_RESOURCES
-uses HAVE_ACPI_RESUME
-uses HAVE_LOW_TABLES
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_HAVE_ACPI_TABLES
+uses CONFIG_HAVE_MAINBOARD_RESOURCES
+uses CONFIG_HAVE_ACPI_RESUME
+uses CONFIG_HAVE_LOW_TABLES
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
-uses _RAMBASE
+uses CONFIG_RAMBASE
uses CONFIG_GDB_STUB
-uses CROSS_COMPILE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_SERIAL8250
-uses HAVE_INIT_TIMER
+uses CONFIG_HAVE_INIT_TIMER
uses CONFIG_GDB_STUB
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
# bx_b001- uses K8_HW_MEM_HOLE_SIZEK
-uses K8_HT_FREQ_1G_SUPPORT
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
-uses DCACHE_RAM_GLOBAL_VAR_SIZE
+uses CONFIG_K8_HT_FREQ_1G_SUPPORT
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
+uses CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE
uses CONFIG_USE_INIT
-uses ENABLE_APIC_EXT_ID
-uses APIC_ID_OFFSET
-uses LIFT_BSP_APIC_ID
-uses HT_CHAIN_UNITID_BASE
-uses HT_CHAIN_END_UNITID_BASE
+uses CONFIG_ENABLE_APIC_EXT_ID
+uses CONFIG_APIC_ID_OFFSET
+uses CONFIG_LIFT_BSP_APIC_ID
+uses CONFIG_HT_CHAIN_UNITID_BASE
+uses CONFIG_HT_CHAIN_END_UNITID_BASE
# bx_b001- uses K8_SB_HT_CHAIN_ON_BUS0
-uses SB_HT_CHAIN_UNITID_OFFSET_ONLY
+uses CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY
# bx_b005+
-uses SB_HT_CHAIN_ON_BUS0
+uses CONFIG_SB_HT_CHAIN_ON_BUS0
uses CONFIG_COMPRESSED_PAYLOAD_NRV2B
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_USE_PRINTK_IN_CAR
-default HAVE_FALLBACK_BOOT = 1
-default HAVE_HARD_RESET = 1
-default HAVE_PIRQ_TABLE = 0
-default IRQ_SLOT_COUNT = 11 # FIXME?
-default HAVE_MP_TABLE = 0
-default HAVE_OPTION_TABLE = 0 # FIXME
+default CONFIG_HAVE_FALLBACK_BOOT = 1
+default CONFIG_HAVE_HARD_RESET = 1
+default CONFIG_HAVE_PIRQ_TABLE = 0
+default CONFIG_IRQ_SLOT_COUNT = 11 # FIXME?
+default CONFIG_HAVE_MP_TABLE = 0
+default CONFIG_HAVE_OPTION_TABLE = 0 # FIXME
# Move the default coreboot CMOS range off of AMD RTC registers.
-default LB_CKS_RANGE_START = 49
-default LB_CKS_RANGE_END = 122
-default LB_CKS_LOC = 123
+default CONFIG_LB_CKS_RANGE_START = 49
+default CONFIG_LB_CKS_RANGE_END = 122
+default CONFIG_LB_CKS_LOC = 123
default CONFIG_SMP = 1
default CONFIG_MAX_CPUS = 2
default CONFIG_MAX_PHYSICAL_CPUS = 1
default CONFIG_LOGICAL_CPUS = 1
-default HAVE_ACPI_TABLES = 1
-default HAVE_MAINBOARD_RESOURCES = 1
-default HAVE_LOW_TABLES = 0
-default HAVE_ACPI_RESUME = 1
+default CONFIG_HAVE_ACPI_TABLES = 1
+default CONFIG_HAVE_MAINBOARD_RESOURCES = 1
+default CONFIG_HAVE_LOW_TABLES = 0
+default CONFIG_HAVE_ACPI_RESUME = 1
# 1G memory hole
# bx_b001- default K8_HW_MEM_HOLE_SIZEK = 0x100000
# Opteron K8 1G HT support
-default K8_HT_FREQ_1G_SUPPORT = 1
+default CONFIG_K8_HT_FREQ_1G_SUPPORT = 1
# HT Unit ID offset, default is 1, the typical one.
-default HT_CHAIN_UNITID_BASE = 0x0
+default CONFIG_HT_CHAIN_UNITID_BASE = 0x0
# Real SB Unit ID, default is 0x20, mean don't touch it at last.
-# default HT_CHAIN_END_UNITID_BASE = 0x0
+# default CONFIG_HT_CHAIN_END_UNITID_BASE = 0x0
# Make the SB HT chain on bus 0, default is not (0).
# bx_b001- default K8_SB_HT_CHAIN_ON_BUS0 = 2
# bx_b005+ make the SB HT chain on bus 0.
-default SB_HT_CHAIN_ON_BUS0 = 1
+default CONFIG_SB_HT_CHAIN_ON_BUS0 = 1
# Only offset for SB chain?, default is yes(1).
-default SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0
+default CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0
default CONFIG_CONSOLE_VGA = 1 # Needed for VGA.
default CONFIG_PCI_ROM_RUN = 0 # Needed for VGA.
-default USE_DCACHE_RAM = 1
-default DCACHE_RAM_BASE = 0xcc000
-default DCACHE_RAM_SIZE = 0x4000
-default DCACHE_RAM_GLOBAL_VAR_SIZE = 0x01000
+default CONFIG_USE_DCACHE_RAM = 1
+default CONFIG_DCACHE_RAM_BASE = 0xcc000
+default CONFIG_DCACHE_RAM_SIZE = 0x4000
+default CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE = 0x01000
default CONFIG_USE_INIT = 0
-default ENABLE_APIC_EXT_ID = 0
-default APIC_ID_OFFSET = 0x10
-default LIFT_BSP_APIC_ID = 0
+default CONFIG_ENABLE_APIC_EXT_ID = 0
+default CONFIG_APIC_ID_OFFSET = 0x10
+default CONFIG_LIFT_BSP_APIC_ID = 0
default CONFIG_IOAPIC = 1
-default MAINBOARD_VENDOR = "ASUS"
-default MAINBOARD_PART_NUMBER = "M2V-MX SE"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID = 0x1043
-# default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID = 0x1234 # FIXME
-default STACK_SIZE = 8 * 1024
-default HEAP_SIZE = 256 * 1024
+default CONFIG_MAINBOARD_VENDOR = "ASUS"
+default CONFIG_MAINBOARD_PART_NUMBER = "M2V-MX SE"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID = 0x1043
+# default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID = 0x1234 # FIXME
+default CONFIG_STACK_SIZE = 8 * 1024
+default CONFIG_HEAP_SIZE = 256 * 1024
# More 1M for pgtbl.
default CONFIG_LB_MEM_TOPK = 32768
# to 1MB
-default _RAMBASE = 0x1F00000
-# default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
+default CONFIG_RAMBASE = 0x1F00000
+# default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
default CONFIG_ROM_PAYLOAD = 1
-default CC = "$(CROSS_COMPILE)gcc -m32"
-default HOSTCC = "gcc"
+default CC = "$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC = "gcc"
default CONFIG_GDB_STUB = 0
default CONFIG_USE_PRINTK_IN_CAR=1
default CONFIG_CONSOLE_SERIAL8250 = 1
-default TTYS0_BAUD = 115200
-default TTYS0_BASE = 0x3f8
-default TTYS0_LCS = 0x3 # 8n1
-default DEFAULT_CONSOLE_LOGLEVEL = 9
-default MAXIMUM_CONSOLE_LOGLEVEL = 9
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL = "MAINBOARD_POWER_ON"
+default CONFIG_TTYS0_BAUD = 115200
+default CONFIG_TTYS0_BASE = 0x3f8
+default CONFIG_TTYS0_LCS = 0x3 # 8n1
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL = "MAINBOARD_POWER_ON"
#
# CBFS
#
/* If we want to wait for core1 done before DQS training, set it to 0. */
#define K8_SET_FIDVID_CORE0_ONLY 1
-#if K8_REV_F_SUPPORT == 1
+#if CONFIG_K8_REV_F_SUPPORT == 1
#define K8_REV_F_SUPPORT_F0_F1_WORKAROUND 0
#endif
unsigned bsp_apicid = 0;
int needs_reset = 0;
struct sys_info *sysinfo =
- (DCACHE_RAM_BASE + DCACHE_RAM_SIZE - DCACHE_RAM_GLOBAL_VAR_SIZE);
+ (CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE);
char *p;
u8 reg;
sio_init();
- it8712f_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ it8712f_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
it8712f_kill_watchdog();
it8712f_enable_3vsbsw();
uart_init();
int add_mainboard_resources(struct lb_memory *mem)
{
-#if HAVE_ACPI_RESUME == 1
+#if CONFIG_HAVE_ACPI_RESUME == 1
lb_add_memory_range(mem, LB_MEM_RESERVED,
- _RAMBASE, ((CONFIG_LB_MEM_TOPK<<10) - _RAMBASE));
+ CONFIG_RAMBASE, ((CONFIG_LB_MEM_TOPK<<10) - CONFIG_RAMBASE));
lb_add_memory_range(mem, LB_MEM_RESERVED,
- DCACHE_RAM_BASE, DCACHE_RAM_SIZE);
+ CONFIG_DCACHE_RAM_BASE, CONFIG_DCACHE_RAM_SIZE);
#endif
return 0;
}
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
arch i386 end
driver mainboard.o
-if HAVE_PIRQ_TABLE
+if CONFIG_HAVE_PIRQ_TABLE
object irq_tables.o
end
makerule ./failover.E
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./auto.E
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
# Note: The -mcpu=p2 is important, or else... 'too few registers'.
- action "../romcc -mcpu=p2 -E -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ action "../romcc -mcpu=p2 -E -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
# Note: The -mcpu=p2 is important, or else... 'too few registers'.
- action "../romcc -mcpu=p2 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ action "../romcc -mcpu=p2 -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
mainboardinit cpu/x86/16bit/entry16.inc
mainboardinit cpu/x86/32bit/entry32.inc
ldscript /cpu/x86/16bit/entry16.lds
ldscript /cpu/x86/32bit/entry32.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
mainboardinit arch/i386/lib/cpu_reset.inc
mainboardinit arch/i386/lib/id.inc
ldscript /arch/i386/lib/id.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_ROM_PAYLOAD
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses HAVE_MP_TABLE
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
-default ROM_SIZE = 512 * 1024 # Override this in targets/*/Config.lb.
-default HAVE_FALLBACK_BOOT = 1
-default HAVE_MP_TABLE = 0
-default HAVE_HARD_RESET = 0
+default CONFIG_ROM_SIZE = 512 * 1024 # Override this in targets/*/Config.lb.
+default CONFIG_HAVE_FALLBACK_BOOT = 1
+default CONFIG_HAVE_MP_TABLE = 0
+default CONFIG_HAVE_HARD_RESET = 0
default CONFIG_UDELAY_TSC = 1
default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 1
-default HAVE_PIRQ_TABLE = 1
-default IRQ_SLOT_COUNT = 0 # Override this in targets/*/Config.lb.
-default MAINBOARD_VENDOR = "N/A" # Override this in targets/*/Config.lb.
-default MAINBOARD_PART_NUMBER = "N/A" # Override this in targets/*/Config.lb.
-default ROM_IMAGE_SIZE = 64 * 1024
-default FALLBACK_SIZE = 128 * 1024
-default STACK_SIZE = 8 * 1024
-default HEAP_SIZE = 16 * 1024
-default HAVE_OPTION_TABLE = 0
-#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_HAVE_PIRQ_TABLE = 1
+default CONFIG_IRQ_SLOT_COUNT = 0 # Override this in targets/*/Config.lb.
+default CONFIG_MAINBOARD_VENDOR = "N/A" # Override this in targets/*/Config.lb.
+default CONFIG_MAINBOARD_PART_NUMBER = "N/A" # Override this in targets/*/Config.lb.
+default CONFIG_ROM_IMAGE_SIZE = 64 * 1024
+default CONFIG_FALLBACK_SIZE = 128 * 1024
+default CONFIG_STACK_SIZE = 8 * 1024
+default CONFIG_HEAP_SIZE = 16 * 1024
+default CONFIG_HAVE_OPTION_TABLE = 0
+#default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 0
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
-default CROSS_COMPILE = ""
-default CC = "$(CROSS_COMPILE)gcc -m32"
-default HOSTCC = "gcc"
+default CONFIG_CROSS_COMPILE = ""
+default CC = "$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC = "gcc"
default CONFIG_CONSOLE_SERIAL8250 = 1
-default TTYS0_BAUD = 115200
-default TTYS0_BASE = 0x3f8
-default TTYS0_LCS = 0x3 # 8n1
-default DEFAULT_CONSOLE_LOGLEVEL = 9 # Override this in targets/*/Config.lb.
-default MAXIMUM_CONSOLE_LOGLEVEL = 9 # Override this in targets/*/Config.lb.
+default CONFIG_TTYS0_BAUD = 115200
+default CONFIG_TTYS0_BASE = 0x3f8
+default CONFIG_TTYS0_LCS = 0x3 # 8n1
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9 # Override this in targets/*/Config.lb.
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9 # Override this in targets/*/Config.lb.
default CONFIG_CONSOLE_VGA = 1 # Override this in targets/*/Config.lb.
default CONFIG_PCI_ROM_RUN = 1 # Override this in targets/*/Config.lb.
if (bist == 0)
early_mtrr_init();
- smscsuperio_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ smscsuperio_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
report_bist_failure(bist);
const struct irq_routing_table intel_irq_routing_table = {
PIRQ_SIGNATURE,
PIRQ_VERSION,
- 32 + 16 * IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
+ 32 + 16 * CONFIG_IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
0x00, /* Interrupt router bus */
(0x1f << 3) | 0x0, /* Interrupt router device */
0, /* IRQs devoted exclusively to PCI usage */
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
##
driver mainboard.o
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
#object reset.o
##
## Romcc output
##
makerule ./failover.E
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./auto.E
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -E -mcpu=p2 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -E -mcpu=p2 -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -mcpu=p2 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -mcpu=p2 -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
##
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_ROM_PAYLOAD
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses HAVE_MP_TABLE
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
uses CONFIG_UDELAY_TSC
uses CONFIG_IDE
-## ROM_SIZE is the size of boot ROM that this board will use.
-default ROM_SIZE = 512*1024
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
+default CONFIG_ROM_SIZE = 512*1024
###
### Build options
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT = 1
+default CONFIG_HAVE_FALLBACK_BOOT = 1
##
## no MP table
##
-default HAVE_MP_TABLE = 0
+default CONFIG_HAVE_MP_TABLE = 0
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET = 0
+default CONFIG_HAVE_HARD_RESET = 0
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE = 1
-default IRQ_SLOT_COUNT = 11
+default CONFIG_HAVE_PIRQ_TABLE = 1
+default CONFIG_IRQ_SLOT_COUNT = 11
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE = 0
+default CONFIG_HAVE_OPTION_TABLE = 0
## IDE Support
default CONFIG_IDE = 1
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
-default FALLBACK_SIZE = 131072
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
+default CONFIG_FALLBACK_SIZE = 131072
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE=0x4000
+default CONFIG_HEAP_SIZE=0x4000
##
## Only use the option table in a normal image
##
-#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
+#default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
##
## The default compiler
##
-default CROSS_COMPILE=""
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CONFIG_CROSS_COMPILE=""
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## The Serial Console
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=9
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=9
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=9
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=9
default CONFIG_UDELAY_TSC=1
if (bist == 0)
early_mtrr_init();
- lpc47b272_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ lpc47b272_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
arch i386 end
driver mainboard.o
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
makerule ./failover.E
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -E -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -E -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./auto.E
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -E -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -E -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
mainboardinit cpu/x86/16bit/entry16.inc
mainboardinit cpu/x86/32bit/entry32.inc
ldscript /cpu/x86/16bit/entry16.lds
ldscript /cpu/x86/32bit/entry32.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
mainboardinit arch/i386/lib/cpu_reset.inc
mainboardinit arch/i386/lib/id.inc
ldscript /arch/i386/lib/id.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_ROM_PAYLOAD
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses HAVE_MP_TABLE
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
uses CONFIG_SMP
uses CONFIG_MAX_CPUS
uses CONFIG_IOAPIC
-default ROM_SIZE = 256 * 1024
-default HAVE_FALLBACK_BOOT = 1
-default HAVE_MP_TABLE = 1
-default HAVE_HARD_RESET = 0
+default CONFIG_ROM_SIZE = 256 * 1024
+default CONFIG_HAVE_FALLBACK_BOOT = 1
+default CONFIG_HAVE_MP_TABLE = 1
+default CONFIG_HAVE_HARD_RESET = 0
default CONFIG_UDELAY_TSC = 1
default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 1
-default HAVE_PIRQ_TABLE = 1
-default IRQ_SLOT_COUNT = 0 # Override this in targets/*/Config.lb.
-default MAINBOARD_VENDOR = "N/A" # Override this in targets/*/Config.lb.
-default MAINBOARD_PART_NUMBER = "N/A" # Override this in targets/*/Config.lb.
-default ROM_IMAGE_SIZE = 64 * 1024
-default FALLBACK_SIZE = 128 * 1024
-default STACK_SIZE = 8 * 1024
-default HEAP_SIZE = 16 * 1024
-default HAVE_OPTION_TABLE = 0
-#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_HAVE_PIRQ_TABLE = 1
+default CONFIG_IRQ_SLOT_COUNT = 0 # Override this in targets/*/Config.lb.
+default CONFIG_MAINBOARD_VENDOR = "N/A" # Override this in targets/*/Config.lb.
+default CONFIG_MAINBOARD_PART_NUMBER = "N/A" # Override this in targets/*/Config.lb.
+default CONFIG_ROM_IMAGE_SIZE = 64 * 1024
+default CONFIG_FALLBACK_SIZE = 128 * 1024
+default CONFIG_STACK_SIZE = 8 * 1024
+default CONFIG_HEAP_SIZE = 16 * 1024
+default CONFIG_HAVE_OPTION_TABLE = 0
+#default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 0
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
default CONFIG_SMP = 1
default CONFIG_MAX_CPUS = 2
default CONFIG_IOAPIC = 1
-default CROSS_COMPILE = ""
-default CC = "$(CROSS_COMPILE)gcc -m32"
-default HOSTCC = "gcc"
+default CONFIG_CROSS_COMPILE = ""
+default CC = "$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC = "gcc"
default CONFIG_CONSOLE_SERIAL8250 = 1
-default TTYS0_BAUD = 115200
-default TTYS0_BASE = 0x3f8
-default TTYS0_LCS = 0x3 # 8n1
-default DEFAULT_CONSOLE_LOGLEVEL = 9
-default MAXIMUM_CONSOLE_LOGLEVEL = 9
+default CONFIG_TTYS0_BAUD = 115200
+default CONFIG_TTYS0_BASE = 0x3f8
+default CONFIG_TTYS0_LCS = 0x3 # 8n1
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
default CONFIG_CONSOLE_VGA = 1
default CONFIG_PCI_ROM_RUN = 1
default CONFIG_CBFS = 0
enable_lapic(); /* FIXME? */
}
- w83977tf_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ w83977tf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
report_bist_failure(bist);
const struct irq_routing_table intel_irq_routing_table = {
PIRQ_SIGNATURE,
PIRQ_VERSION,
- 32 + 16 * IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
+ 32 + 16 * CONFIG_IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
0x00, /* Interrupt router bus */
(0x04 << 3) | 0x0, /* Interrupt router device */
0, /* IRQs devoted exclusively to PCI usage */
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
arch i386 end
driver mainboard.o
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
makerule ./failover.E
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -E -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -E -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./auto.E
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -E -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -E -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
mainboardinit cpu/x86/16bit/entry16.inc
mainboardinit cpu/x86/32bit/entry32.inc
ldscript /cpu/x86/16bit/entry16.lds
ldscript /cpu/x86/32bit/entry32.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
mainboardinit arch/i386/lib/cpu_reset.inc
mainboardinit arch/i386/lib/id.inc
ldscript /arch/i386/lib/id.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_ROM_PAYLOAD
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses HAVE_MP_TABLE
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
uses CONFIG_SMP
uses CONFIG_MAX_CPUS
uses CONFIG_IOAPIC
-default ROM_SIZE = 256 * 1024
-default HAVE_FALLBACK_BOOT = 1
-default HAVE_MP_TABLE = 1
-default HAVE_HARD_RESET = 0
+default CONFIG_ROM_SIZE = 256 * 1024
+default CONFIG_HAVE_FALLBACK_BOOT = 1
+default CONFIG_HAVE_MP_TABLE = 1
+default CONFIG_HAVE_HARD_RESET = 0
default CONFIG_UDELAY_TSC = 1
default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 1
-default HAVE_PIRQ_TABLE = 1
-default IRQ_SLOT_COUNT = 0 # Override this in targets/*/Config.lb.
-default MAINBOARD_VENDOR = "N/A" # Override this in targets/*/Config.lb.
-default MAINBOARD_PART_NUMBER = "N/A" # Override this in targets/*/Config.lb.
-default ROM_IMAGE_SIZE = 64 * 1024
-default FALLBACK_SIZE = 128 * 1024
-default STACK_SIZE = 8 * 1024
-default HEAP_SIZE = 16 * 1024
-default HAVE_OPTION_TABLE = 0
-#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_HAVE_PIRQ_TABLE = 1
+default CONFIG_IRQ_SLOT_COUNT = 0 # Override this in targets/*/Config.lb.
+default CONFIG_MAINBOARD_VENDOR = "N/A" # Override this in targets/*/Config.lb.
+default CONFIG_MAINBOARD_PART_NUMBER = "N/A" # Override this in targets/*/Config.lb.
+default CONFIG_ROM_IMAGE_SIZE = 64 * 1024
+default CONFIG_FALLBACK_SIZE = 128 * 1024
+default CONFIG_STACK_SIZE = 8 * 1024
+default CONFIG_HEAP_SIZE = 16 * 1024
+default CONFIG_HAVE_OPTION_TABLE = 0
+#default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 0
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
default CONFIG_SMP = 1
default CONFIG_MAX_CPUS = 2
default CONFIG_IOAPIC = 1
-default CROSS_COMPILE = ""
-default CC = "$(CROSS_COMPILE)gcc -m32"
-default HOSTCC = "gcc"
+default CONFIG_CROSS_COMPILE = ""
+default CC = "$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC = "gcc"
default CONFIG_CONSOLE_SERIAL8250 = 1
-default TTYS0_BAUD = 115200
-default TTYS0_BASE = 0x3f8
-default TTYS0_LCS = 0x3 # 8n1
-default DEFAULT_CONSOLE_LOGLEVEL = 9
-default MAXIMUM_CONSOLE_LOGLEVEL = 9
+default CONFIG_TTYS0_BAUD = 115200
+default CONFIG_TTYS0_BASE = 0x3f8
+default CONFIG_TTYS0_LCS = 0x3 # 8n1
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
default CONFIG_CONSOLE_VGA = 1
default CONFIG_PCI_ROM_RUN = 1
enable_lapic(); /* FIXME? */
}
- w83977tf_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ w83977tf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
report_bist_failure(bist);
const struct irq_routing_table intel_irq_routing_table = {
PIRQ_SIGNATURE,
PIRQ_VERSION,
- 32 + 16 * IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
+ 32 + 16 * CONFIG_IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
0x00, /* Interrupt router bus */
(0x04 << 3) | 0x0, /* Interrupt router device */
0, /* IRQs devoted exclusively to PCI usage */
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
arch i386 end
driver mainboard.o
-if HAVE_PIRQ_TABLE
+if CONFIG_HAVE_PIRQ_TABLE
object irq_tables.o
end
makerule ./failover.E
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -E -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -E -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./auto.E
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -E -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -E -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
mainboardinit cpu/x86/16bit/entry16.inc
mainboardinit cpu/x86/32bit/entry32.inc
ldscript /cpu/x86/16bit/entry16.lds
ldscript /cpu/x86/32bit/entry32.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
mainboardinit arch/i386/lib/cpu_reset.inc
mainboardinit arch/i386/lib/id.inc
ldscript /arch/i386/lib/id.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_ROM_PAYLOAD
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses HAVE_MP_TABLE
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
-default ROM_SIZE = 256 * 1024
-default HAVE_FALLBACK_BOOT = 1
-default HAVE_MP_TABLE = 0
-default HAVE_HARD_RESET = 0
+default CONFIG_ROM_SIZE = 256 * 1024
+default CONFIG_HAVE_FALLBACK_BOOT = 1
+default CONFIG_HAVE_MP_TABLE = 0
+default CONFIG_HAVE_HARD_RESET = 0
default CONFIG_UDELAY_TSC = 1
default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 1
-default HAVE_PIRQ_TABLE = 1
-default IRQ_SLOT_COUNT = 0 # Override this in targets/*/Config.lb.
-default MAINBOARD_VENDOR = "N/A" # Override this in targets/*/Config.lb.
-default MAINBOARD_PART_NUMBER = "N/A" # Override this in targets/*/Config.lb.
-default ROM_IMAGE_SIZE = 64 * 1024
-default FALLBACK_SIZE = 128 * 1024
-default STACK_SIZE = 8 * 1024
-default HEAP_SIZE = 16 * 1024
-default HAVE_OPTION_TABLE = 0
-#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_HAVE_PIRQ_TABLE = 1
+default CONFIG_IRQ_SLOT_COUNT = 0 # Override this in targets/*/Config.lb.
+default CONFIG_MAINBOARD_VENDOR = "N/A" # Override this in targets/*/Config.lb.
+default CONFIG_MAINBOARD_PART_NUMBER = "N/A" # Override this in targets/*/Config.lb.
+default CONFIG_ROM_IMAGE_SIZE = 64 * 1024
+default CONFIG_FALLBACK_SIZE = 128 * 1024
+default CONFIG_STACK_SIZE = 8 * 1024
+default CONFIG_HEAP_SIZE = 16 * 1024
+default CONFIG_HAVE_OPTION_TABLE = 0
+#default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 0
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
-default CROSS_COMPILE = ""
-default CC = "$(CROSS_COMPILE)gcc -m32"
-default HOSTCC = "gcc"
+default CONFIG_CROSS_COMPILE = ""
+default CC = "$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC = "gcc"
default CONFIG_CONSOLE_SERIAL8250 = 1
-default TTYS0_BAUD = 115200
-default TTYS0_BASE = 0x3f8
-default TTYS0_LCS = 0x3 # 8n1
-default DEFAULT_CONSOLE_LOGLEVEL = 9
-default MAXIMUM_CONSOLE_LOGLEVEL = 9
+default CONFIG_TTYS0_BAUD = 115200
+default CONFIG_TTYS0_BASE = 0x3f8
+default CONFIG_TTYS0_LCS = 0x3 # 8n1
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
default CONFIG_CONSOLE_VGA = 1
default CONFIG_PCI_ROM_RUN = 1
early_mtrr_init();
/* FIXME: The ASUS P2B-F has a Winbond W83977EF, actually. */
- w83977tf_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ w83977tf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
report_bist_failure(bist);
const struct irq_routing_table intel_irq_routing_table = {
PIRQ_SIGNATURE,
PIRQ_VERSION,
- 32 + 16 * IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
+ 32 + 16 * CONFIG_IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
0x00, /* Interrupt router bus */
(0x04 << 3) | 0x0, /* Interrupt router device */
0, /* IRQs devoted exclusively to PCI usage */
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
arch i386 end
driver mainboard.o
-if HAVE_PIRQ_TABLE
+if CONFIG_HAVE_PIRQ_TABLE
object irq_tables.o
end
makerule ./failover.E
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -E -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -E -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./auto.E
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -E -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -E -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
mainboardinit cpu/x86/16bit/entry16.inc
mainboardinit cpu/x86/32bit/entry32.inc
ldscript /cpu/x86/16bit/entry16.lds
ldscript /cpu/x86/32bit/entry32.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
mainboardinit arch/i386/lib/cpu_reset.inc
mainboardinit arch/i386/lib/id.inc
ldscript /arch/i386/lib/id.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_ROM_PAYLOAD
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses HAVE_MP_TABLE
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
-default ROM_SIZE = 256 * 1024
-default HAVE_FALLBACK_BOOT = 1
-default HAVE_MP_TABLE = 0
-default HAVE_HARD_RESET = 0
+default CONFIG_ROM_SIZE = 256 * 1024
+default CONFIG_HAVE_FALLBACK_BOOT = 1
+default CONFIG_HAVE_MP_TABLE = 0
+default CONFIG_HAVE_HARD_RESET = 0
default CONFIG_UDELAY_TSC = 1
default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 1
-default HAVE_PIRQ_TABLE = 1
-default IRQ_SLOT_COUNT = 0 # Override this in targets/*/Config.lb.
-default MAINBOARD_VENDOR = "N/A" # Override this in targets/*/Config.lb.
-default MAINBOARD_PART_NUMBER = "N/A" # Override this in targets/*/Config.lb.
-default ROM_IMAGE_SIZE = 64 * 1024
-default FALLBACK_SIZE = 128 * 1024
-default STACK_SIZE = 8 * 1024
-default HEAP_SIZE = 16 * 1024
-default HAVE_OPTION_TABLE = 0
-#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_HAVE_PIRQ_TABLE = 1
+default CONFIG_IRQ_SLOT_COUNT = 0 # Override this in targets/*/Config.lb.
+default CONFIG_MAINBOARD_VENDOR = "N/A" # Override this in targets/*/Config.lb.
+default CONFIG_MAINBOARD_PART_NUMBER = "N/A" # Override this in targets/*/Config.lb.
+default CONFIG_ROM_IMAGE_SIZE = 64 * 1024
+default CONFIG_FALLBACK_SIZE = 128 * 1024
+default CONFIG_STACK_SIZE = 8 * 1024
+default CONFIG_HEAP_SIZE = 16 * 1024
+default CONFIG_HAVE_OPTION_TABLE = 0
+#default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 0
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
-default CROSS_COMPILE = ""
-default CC = "$(CROSS_COMPILE)gcc -m32"
-default HOSTCC = "gcc"
+default CONFIG_CROSS_COMPILE = ""
+default CC = "$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC = "gcc"
default CONFIG_CONSOLE_SERIAL8250 = 1
-default TTYS0_BAUD = 115200
-default TTYS0_BASE = 0x3f8
-default TTYS0_LCS = 0x3 # 8n1
-default DEFAULT_CONSOLE_LOGLEVEL = 9
-default MAXIMUM_CONSOLE_LOGLEVEL = 9
+default CONFIG_TTYS0_BAUD = 115200
+default CONFIG_TTYS0_BASE = 0x3f8
+default CONFIG_TTYS0_LCS = 0x3 # 8n1
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
default CONFIG_CONSOLE_VGA = 1
default CONFIG_PCI_ROM_RUN = 1
if (bist == 0)
early_mtrr_init();
- w83977tf_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ w83977tf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
report_bist_failure(bist);
const struct irq_routing_table intel_irq_routing_table = {
PIRQ_SIGNATURE,
PIRQ_VERSION,
- 32 + 16 * IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
+ 32 + 16 * CONFIG_IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
0x00, /* Interrupt router bus */
(0x04 << 3) | 0x0, /* Interrupt router device */
0, /* IRQs devoted exclusively to PCI usage */
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
arch i386 end
driver mainboard.o
-if HAVE_PIRQ_TABLE
+if CONFIG_HAVE_PIRQ_TABLE
object irq_tables.o
end
makerule ./failover.E
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -E -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -E -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./auto.E
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -E -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -E -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
mainboardinit cpu/x86/16bit/entry16.inc
mainboardinit cpu/x86/32bit/entry32.inc
ldscript /cpu/x86/16bit/entry16.lds
ldscript /cpu/x86/32bit/entry32.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
mainboardinit arch/i386/lib/cpu_reset.inc
mainboardinit arch/i386/lib/id.inc
ldscript /arch/i386/lib/id.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_ROM_PAYLOAD
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses HAVE_MP_TABLE
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
-default ROM_SIZE = 256 * 1024
-default HAVE_FALLBACK_BOOT = 1
-default HAVE_MP_TABLE = 0
-default HAVE_HARD_RESET = 0
+default CONFIG_ROM_SIZE = 256 * 1024
+default CONFIG_HAVE_FALLBACK_BOOT = 1
+default CONFIG_HAVE_MP_TABLE = 0
+default CONFIG_HAVE_HARD_RESET = 0
default CONFIG_UDELAY_TSC = 1
default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 1
-default HAVE_PIRQ_TABLE = 1
-default IRQ_SLOT_COUNT = 0 # Override this in targets/*/Config.lb.
-default MAINBOARD_VENDOR = "N/A" # Override this in targets/*/Config.lb.
-default MAINBOARD_PART_NUMBER = "N/A" # Override this in targets/*/Config.lb.
-default ROM_IMAGE_SIZE = 64 * 1024
-default FALLBACK_SIZE = 128 * 1024
-default STACK_SIZE = 8 * 1024
-default HEAP_SIZE = 16 * 1024
-default HAVE_OPTION_TABLE = 0
-#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_HAVE_PIRQ_TABLE = 1
+default CONFIG_IRQ_SLOT_COUNT = 0 # Override this in targets/*/Config.lb.
+default CONFIG_MAINBOARD_VENDOR = "N/A" # Override this in targets/*/Config.lb.
+default CONFIG_MAINBOARD_PART_NUMBER = "N/A" # Override this in targets/*/Config.lb.
+default CONFIG_ROM_IMAGE_SIZE = 64 * 1024
+default CONFIG_FALLBACK_SIZE = 128 * 1024
+default CONFIG_STACK_SIZE = 8 * 1024
+default CONFIG_HEAP_SIZE = 16 * 1024
+default CONFIG_HAVE_OPTION_TABLE = 0
+#default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 0
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
-default CROSS_COMPILE = ""
-default CC = "$(CROSS_COMPILE)gcc -m32"
-default HOSTCC = "gcc"
+default CONFIG_CROSS_COMPILE = ""
+default CC = "$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC = "gcc"
default CONFIG_CONSOLE_SERIAL8250 = 1
-default TTYS0_BAUD = 115200
-default TTYS0_BASE = 0x3f8
-default TTYS0_LCS = 0x3 # 8n1
-default DEFAULT_CONSOLE_LOGLEVEL = 9
-default MAXIMUM_CONSOLE_LOGLEVEL = 9
+default CONFIG_TTYS0_BAUD = 115200
+default CONFIG_TTYS0_BASE = 0x3f8
+default CONFIG_TTYS0_LCS = 0x3 # 8n1
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
default CONFIG_CONSOLE_VGA = 1
default CONFIG_PCI_ROM_RUN = 1
early_mtrr_init();
/* FIXME: The ASUS P3B-F has a Winbond W83977EF, actually. */
- w83977tf_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ w83977tf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
report_bist_failure(bist);
const struct irq_routing_table intel_irq_routing_table = {
PIRQ_SIGNATURE,
PIRQ_VERSION,
- 32 + 16 * IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
+ 32 + 16 * CONFIG_IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
0x00, /* Interrupt router bus */
(0x04 << 3) | 0x0, /* Interrupt router device */
0, /* IRQs devoted exclusively to PCI usage */
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
arch i386 end
driver mainboard.o
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
makerule ./failover.E
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./auto.E
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -E -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -E -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
mainboardinit cpu/x86/16bit/entry16.inc
mainboardinit cpu/x86/32bit/entry32.inc
ldscript /cpu/x86/16bit/entry16.lds
ldscript /cpu/x86/32bit/entry32.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
mainboardinit arch/i386/lib/cpu_reset.inc
mainboardinit arch/i386/lib/id.inc
ldscript /arch/i386/lib/id.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_ROM_PAYLOAD
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
uses CONFIG_SPLASH_GRAPHIC
uses CONFIG_GX1_VIDEO
uses CONFIG_GX1_VIDEOMODE
-uses PIRQ_ROUTE
+uses CONFIG_PIRQ_ROUTE
## Enable VGA with a splash screen (only 640x480 to run on most monitors).
## We want to support up to 1024x768@16 so we need 2MiB video memory.
default CONFIG_SPLASH_GRAPHIC = 1
default CONFIG_VIDEO_MB = 2
-default ROM_SIZE = 256 * 1024
-default MAINBOARD_VENDOR = "AXUS"
-default MAINBOARD_PART_NUMBER = "TC320"
-default HAVE_FALLBACK_BOOT = 1
-default HAVE_MP_TABLE = 0
-default HAVE_HARD_RESET = 0
+default CONFIG_ROM_SIZE = 256 * 1024
+default CONFIG_MAINBOARD_VENDOR = "AXUS"
+default CONFIG_MAINBOARD_PART_NUMBER = "TC320"
+default CONFIG_HAVE_FALLBACK_BOOT = 1
+default CONFIG_HAVE_MP_TABLE = 0
+default CONFIG_HAVE_HARD_RESET = 0
default CONFIG_UDELAY_TSC = 1
default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 1
-default HAVE_PIRQ_TABLE = 1
-default IRQ_SLOT_COUNT = 2 # Soldered NIC, internal USB, no real slots
-default PIRQ_ROUTE = 1
-default HAVE_OPTION_TABLE = 0
-default ROM_IMAGE_SIZE = 64 * 1024
-default FALLBACK_SIZE = 128 * 1024
-default STACK_SIZE = 8 * 1024
-default HEAP_SIZE = 16 * 1024
-default USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_HAVE_PIRQ_TABLE = 1
+default CONFIG_IRQ_SLOT_COUNT = 2 # Soldered NIC, internal USB, no real slots
+default CONFIG_PIRQ_ROUTE = 1
+default CONFIG_HAVE_OPTION_TABLE = 0
+default CONFIG_ROM_IMAGE_SIZE = 64 * 1024
+default CONFIG_FALLBACK_SIZE = 128 * 1024
+default CONFIG_STACK_SIZE = 8 * 1024
+default CONFIG_HEAP_SIZE = 16 * 1024
+default CONFIG_USE_OPTION_TABLE = 0
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
-default CROSS_COMPILE = ""
-default CC = "$(CROSS_COMPILE)gcc "
-default HOSTCC = "gcc"
+default CONFIG_CROSS_COMPILE = ""
+default CC = "$(CONFIG_CROSS_COMPILE)gcc "
+default CONFIG_HOSTCC = "gcc"
default CONFIG_CONSOLE_SERIAL8250 = 1
-default TTYS0_BAUD = 115200
-default TTYS0_BASE = 0x3f8
-default TTYS0_LCS = 0x3 # 8n1
-default DEFAULT_CONSOLE_LOGLEVEL = 6
-default MAXIMUM_CONSOLE_LOGLEVEL = 6
+default CONFIG_TTYS0_BAUD = 115200
+default CONFIG_TTYS0_BASE = 0x3f8
+default CONFIG_TTYS0_LCS = 0x3 # 8n1
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 6
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 6
#
# CBFS
static void main(unsigned long bist)
{
- pc97317_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ pc97317_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
report_bist_failure(bist);
const struct irq_routing_table intel_irq_routing_table = {
.signature = PIRQ_SIGNATURE, /* PIRQ signature */
.version = PIRQ_VERSION, /* PIRQ version */
- .size = 32 + 16 * IRQ_SLOT_COUNT,/* Max. IRQ_SLOT_COUNT devices */
+ .size = 32 + 16 * CONFIG_IRQ_SLOT_COUNT,/* Max. CONFIG_IRQ_SLOT_COUNT devices */
.rtr_bus = 0x00, /* Interrupt router bus */
.rtr_devfn = (0x12 << 3) | 0x0, /* Interrupt router device */
.exclusive_irqs = IRQ_DEVOTED_TO_PCI, /* IRQs devoted to PCI */
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
arch i386 end
driver mainboard.o
-if HAVE_PIRQ_TABLE
+if CONFIG_HAVE_PIRQ_TABLE
object irq_tables.o
end
makerule ./failover.E
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -E -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -E -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./auto.E
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -E -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -E -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
mainboardinit cpu/x86/16bit/entry16.inc
mainboardinit cpu/x86/32bit/entry32.inc
ldscript /cpu/x86/16bit/entry16.lds
ldscript /cpu/x86/32bit/entry32.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
mainboardinit arch/i386/lib/cpu_reset.inc
mainboardinit arch/i386/lib/id.inc
ldscript /arch/i386/lib/id.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_ROM_PAYLOAD
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses HAVE_MP_TABLE
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
-default ROM_SIZE = 256 * 1024
-default HAVE_FALLBACK_BOOT = 1
-default HAVE_MP_TABLE = 0
-default HAVE_HARD_RESET = 0
+default CONFIG_ROM_SIZE = 256 * 1024
+default CONFIG_HAVE_FALLBACK_BOOT = 1
+default CONFIG_HAVE_MP_TABLE = 0
+default CONFIG_HAVE_HARD_RESET = 0
default CONFIG_UDELAY_TSC = 1
default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 1
-default HAVE_PIRQ_TABLE = 1
-default IRQ_SLOT_COUNT = 0 # Override this in targets/*/Config.lb.
-default MAINBOARD_VENDOR = "N/A" # Override this in targets/*/Config.lb.
-default MAINBOARD_PART_NUMBER = "N/A" # Override this in targets/*/Config.lb.
-default ROM_IMAGE_SIZE = 64 * 1024
-default FALLBACK_SIZE = 128 * 1024
-default STACK_SIZE = 8 * 1024
-default HEAP_SIZE = 16 * 1024
-default HAVE_OPTION_TABLE = 0
-#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_HAVE_PIRQ_TABLE = 1
+default CONFIG_IRQ_SLOT_COUNT = 0 # Override this in targets/*/Config.lb.
+default CONFIG_MAINBOARD_VENDOR = "N/A" # Override this in targets/*/Config.lb.
+default CONFIG_MAINBOARD_PART_NUMBER = "N/A" # Override this in targets/*/Config.lb.
+default CONFIG_ROM_IMAGE_SIZE = 64 * 1024
+default CONFIG_FALLBACK_SIZE = 128 * 1024
+default CONFIG_STACK_SIZE = 8 * 1024
+default CONFIG_HEAP_SIZE = 16 * 1024
+default CONFIG_HAVE_OPTION_TABLE = 0
+#default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 0
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
-default CROSS_COMPILE = ""
-default CC = "$(CROSS_COMPILE)gcc -m32"
-default HOSTCC = "gcc"
+default CONFIG_CROSS_COMPILE = ""
+default CC = "$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC = "gcc"
default CONFIG_CONSOLE_SERIAL8250 = 1
-default TTYS0_BAUD = 115200
-default TTYS0_BASE = 0x3f8
-default TTYS0_LCS = 0x3 # 8n1
-default DEFAULT_CONSOLE_LOGLEVEL = 9
-default MAXIMUM_CONSOLE_LOGLEVEL = 9
+default CONFIG_TTYS0_BAUD = 115200
+default CONFIG_TTYS0_BASE = 0x3f8
+default CONFIG_TTYS0_LCS = 0x3 # 8n1
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
default CONFIG_CONSOLE_VGA = 1
default CONFIG_PCI_ROM_RUN = 1
early_mtrr_init();
/* FIXME: It's a Winbond W83977EF, actually. */
- w83977tf_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ w83977tf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
report_bist_failure(bist);
const struct irq_routing_table intel_irq_routing_table = {
PIRQ_SIGNATURE,
PIRQ_VERSION,
- 32 + 16 * IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
+ 32 + 16 * CONFIG_IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
0x00, /* Interrupt router bus */
(0x07 << 3) | 0x0, /* Interrupt router device */
0xc00, /* IRQs devoted exclusively to PCI usage */
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
arch i386 end
driver mainboard.o
-if HAVE_PIRQ_TABLE
+if CONFIG_HAVE_PIRQ_TABLE
object irq_tables.o
end
makerule ./failover.E
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./auto.E
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -E -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -E -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
mainboardinit cpu/x86/16bit/entry16.inc
mainboardinit cpu/x86/32bit/entry32.inc
ldscript /cpu/x86/16bit/entry16.lds
ldscript /cpu/x86/32bit/entry32.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
mainboardinit arch/i386/lib/cpu_reset.inc
mainboardinit arch/i386/lib/id.inc
ldscript /arch/i386/lib/id.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_ROM_PAYLOAD
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
uses CONFIG_SPLASH_GRAPHIC
uses CONFIG_GX1_VIDEO
uses CONFIG_GX1_VIDEOMODE
-uses PIRQ_ROUTE
+uses CONFIG_PIRQ_ROUTE
## Enable VGA with a splash screen (only 640x480 to run on most monitors).
## We want to support up to 1024x768@16 so we need 2MiB video memory.
default CONFIG_SPLASH_GRAPHIC = 1
default CONFIG_VIDEO_MB = 2
-default ROM_SIZE = 256 * 1024
-default MAINBOARD_VENDOR = "BCOM"
-default MAINBOARD_PART_NUMBER = "WinNET100"
-default HAVE_FALLBACK_BOOT = 1
-default HAVE_MP_TABLE = 0
-default HAVE_HARD_RESET = 0
+default CONFIG_ROM_SIZE = 256 * 1024
+default CONFIG_MAINBOARD_VENDOR = "BCOM"
+default CONFIG_MAINBOARD_PART_NUMBER = "WinNET100"
+default CONFIG_HAVE_FALLBACK_BOOT = 1
+default CONFIG_HAVE_MP_TABLE = 0
+default CONFIG_HAVE_HARD_RESET = 0
default CONFIG_UDELAY_TSC = 1
default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 1
-default HAVE_PIRQ_TABLE = 1
-default IRQ_SLOT_COUNT = 2 # Soldered NIC, internal USB, no real slots
-default PIRQ_ROUTE = 1
-default HAVE_OPTION_TABLE = 0
-default ROM_IMAGE_SIZE = 64 * 1024
-default FALLBACK_SIZE = 128 * 1024
-default STACK_SIZE = 8 * 1024
-default HEAP_SIZE = 16 * 1024
-default USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_HAVE_PIRQ_TABLE = 1
+default CONFIG_IRQ_SLOT_COUNT = 2 # Soldered NIC, internal USB, no real slots
+default CONFIG_PIRQ_ROUTE = 1
+default CONFIG_HAVE_OPTION_TABLE = 0
+default CONFIG_ROM_IMAGE_SIZE = 64 * 1024
+default CONFIG_FALLBACK_SIZE = 128 * 1024
+default CONFIG_STACK_SIZE = 8 * 1024
+default CONFIG_HEAP_SIZE = 16 * 1024
+default CONFIG_USE_OPTION_TABLE = 0
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
-default CROSS_COMPILE = ""
-default CC = "$(CROSS_COMPILE)gcc "
-default HOSTCC = "gcc"
+default CONFIG_CROSS_COMPILE = ""
+default CC = "$(CONFIG_CROSS_COMPILE)gcc "
+default CONFIG_HOSTCC = "gcc"
default CONFIG_CONSOLE_SERIAL8250 = 1
-default TTYS0_BAUD = 115200
-default TTYS0_BASE = 0x3f8
-default TTYS0_LCS = 0x3 # 8n1
-default DEFAULT_CONSOLE_LOGLEVEL = 6
-default MAXIMUM_CONSOLE_LOGLEVEL = 6
+default CONFIG_TTYS0_BAUD = 115200
+default CONFIG_TTYS0_BASE = 0x3f8
+default CONFIG_TTYS0_LCS = 0x3 # 8n1
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 6
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 6
#
# CBFS
static void main(unsigned long bist)
{
/* Initialize the serial console. */
- pc97317_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ pc97317_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
const struct irq_routing_table intel_irq_routing_table = {
.signature = PIRQ_SIGNATURE, /* PIRQ signature */
.version = PIRQ_VERSION, /* PIRQ version */
- .size = 32 +16 * IRQ_SLOT_COUNT,/* Max. IRQ_SLOT_COUNT devices */
+ .size = 32 +16 * CONFIG_IRQ_SLOT_COUNT,/* Max. CONFIG_IRQ_SLOT_COUNT devices */
.rtr_bus = 0x00, /* Interrupt router bus */
.rtr_devfn = (0x12 << 3) | 0x0, /* Interrupt router device */
.exclusive_irqs = IRQ_DEVOTED_TO_PCI, /* IRQs devoted to PCI */
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
arch i386 end
driver mainboard.o
-if HAVE_PIRQ_TABLE object irq_tables.o end
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_ACPI_TABLES
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_ACPI_TABLES
object fadt.o
object dsdt.o
object acpi_tables.o
end
makerule ./failover.E
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./auto.E
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -E -mcpu=c3 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -E -mcpu=c3 -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -mcpu=c3 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -mcpu=c3 -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
mainboardinit cpu/x86/16bit/entry16.inc
mainboardinit cpu/x86/32bit/entry32.inc
ldscript /cpu/x86/16bit/entry16.lds
ldscript /cpu/x86/32bit/entry32.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
mainboardinit arch/i386/lib/cpu_reset.inc
mainboardinit arch/i386/lib/id.inc
ldscript /arch/i386/lib/id.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_ROM_PAYLOAD
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_NRV2B
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses HAVE_MP_TABLE
-uses HAVE_ACPI_TABLES
-uses HAVE_ACPI_RESUME
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_HAVE_ACPI_TABLES
+uses CONFIG_HAVE_ACPI_RESUME
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
uses CONFIG_VIDEO_MB
uses CONFIG_IOAPIC
-default ROM_SIZE = 512 * 1024
+default CONFIG_ROM_SIZE = 512 * 1024
default CONFIG_IOAPIC = 0
default CONFIG_VIDEO_MB = 32
default CONFIG_CONSOLE_SERIAL8250 = 1
default CONFIG_PCI_ROM_RUN = 0
default CONFIG_CONSOLE_VGA = 0
-default HAVE_FALLBACK_BOOT = 1
-default HAVE_MP_TABLE = 0
+default CONFIG_HAVE_FALLBACK_BOOT = 1
+default CONFIG_HAVE_MP_TABLE = 0
default CONFIG_UDELAY_TSC = 1
default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 1
-default HAVE_HARD_RESET = 0
-default HAVE_PIRQ_TABLE = 1
-default IRQ_SLOT_COUNT = 10
-default HAVE_ACPI_TABLES = 0
-default HAVE_OPTION_TABLE = 1
-default ROM_IMAGE_SIZE = 64 * 1024
-default FALLBACK_SIZE = ROM_SIZE
-default USE_FALLBACK_IMAGE = 1
-default STACK_SIZE = 8 * 1024
-default HEAP_SIZE = 16 * 1024
-#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_HAVE_HARD_RESET = 0
+default CONFIG_HAVE_PIRQ_TABLE = 1
+default CONFIG_IRQ_SLOT_COUNT = 10
+default CONFIG_HAVE_ACPI_TABLES = 0
+default CONFIG_HAVE_OPTION_TABLE = 1
+default CONFIG_ROM_IMAGE_SIZE = 64 * 1024
+default CONFIG_FALLBACK_SIZE = CONFIG_ROM_SIZE
+default CONFIG_USE_FALLBACK_IMAGE = 1
+default CONFIG_STACK_SIZE = 8 * 1024
+default CONFIG_HEAP_SIZE = 16 * 1024
+#default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 0
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
-default CROSS_COMPILE = ""
-default CC = "$(CROSS_COMPILE)gcc -m32 -fno-stack-protector"
-default HOSTCC = "gcc"
+default CONFIG_CROSS_COMPILE = ""
+default CC = "$(CONFIG_CROSS_COMPILE)gcc -m32 -fno-stack-protector"
+default CONFIG_HOSTCC = "gcc"
##
## Set this to the max PCI bus number you would ever use for PCI config I/O.
w83697hf_set_clksel_48(SERIAL_DEV);
- w83697hf_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ w83697hf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
const struct irq_routing_table intel_irq_routing_table = {
PIRQ_SIGNATURE,
PIRQ_VERSION,
- 32 + 16 * IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
+ 32 + 16 * CONFIG_IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
0x00, /* Interrupt router bus */
(0x11 << 3) | 0x0, /* Interrupt router device */
0x828, /* IRQs devoted exclusively to PCI usage */
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
arch i386 end
driver mainboard.o
-if HAVE_PIRQ_TABLE
+if CONFIG_HAVE_PIRQ_TABLE
object irq_tables.o
end
makerule ./failover.E
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -E -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -E -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./auto.E
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -E -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -E -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
mainboardinit cpu/x86/16bit/entry16.inc
mainboardinit cpu/x86/32bit/entry32.inc
ldscript /cpu/x86/16bit/entry16.lds
ldscript /cpu/x86/32bit/entry32.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
mainboardinit arch/i386/lib/cpu_reset.inc
mainboardinit arch/i386/lib/id.inc
ldscript /arch/i386/lib/id.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_ROM_PAYLOAD
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses HAVE_MP_TABLE
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
-default ROM_SIZE = 256 * 1024
-default HAVE_FALLBACK_BOOT = 1
-default HAVE_MP_TABLE = 0
-default HAVE_HARD_RESET = 0
+default CONFIG_ROM_SIZE = 256 * 1024
+default CONFIG_HAVE_FALLBACK_BOOT = 1
+default CONFIG_HAVE_MP_TABLE = 0
+default CONFIG_HAVE_HARD_RESET = 0
default CONFIG_UDELAY_TSC = 1
default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 1
-default HAVE_PIRQ_TABLE = 1
-default IRQ_SLOT_COUNT = 0 # Override this in targets/*/Config.lb.
-default MAINBOARD_VENDOR = "N/A" # Override this in targets/*/Config.lb.
-default MAINBOARD_PART_NUMBER = "N/A" # Override this in targets/*/Config.lb.
-default ROM_IMAGE_SIZE = 64 * 1024
-default FALLBACK_SIZE = 128 * 1024
-default STACK_SIZE = 8 * 1024
-default HEAP_SIZE = 16 * 1024
-default HAVE_OPTION_TABLE = 0
-#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_HAVE_PIRQ_TABLE = 1
+default CONFIG_IRQ_SLOT_COUNT = 0 # Override this in targets/*/Config.lb.
+default CONFIG_MAINBOARD_VENDOR = "N/A" # Override this in targets/*/Config.lb.
+default CONFIG_MAINBOARD_PART_NUMBER = "N/A" # Override this in targets/*/Config.lb.
+default CONFIG_ROM_IMAGE_SIZE = 64 * 1024
+default CONFIG_FALLBACK_SIZE = 128 * 1024
+default CONFIG_STACK_SIZE = 8 * 1024
+default CONFIG_HEAP_SIZE = 16 * 1024
+default CONFIG_HAVE_OPTION_TABLE = 0
+#default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 0
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
-default CROSS_COMPILE = ""
-default CC = "$(CROSS_COMPILE)gcc -m32"
-default HOSTCC = "gcc"
+default CONFIG_CROSS_COMPILE = ""
+default CC = "$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC = "gcc"
default CONFIG_CONSOLE_SERIAL8250 = 1
-default TTYS0_BAUD = 115200
-default TTYS0_BASE = 0x3f8
-default TTYS0_LCS = 0x3 # 8n1
-default DEFAULT_CONSOLE_LOGLEVEL = 9
-default MAXIMUM_CONSOLE_LOGLEVEL = 9
+default CONFIG_TTYS0_BAUD = 115200
+default CONFIG_TTYS0_BASE = 0x3f8
+default CONFIG_TTYS0_LCS = 0x3 # 8n1
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
default CONFIG_CONSOLE_VGA = 1
default CONFIG_PCI_ROM_RUN = 1
if (bist == 0)
early_mtrr_init();
- smscsuperio_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ smscsuperio_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
report_bist_failure(bist);
const struct irq_routing_table intel_irq_routing_table = {
PIRQ_SIGNATURE,
PIRQ_VERSION,
- 32 + 16 * IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
+ 32 + 16 * CONFIG_IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
0x00, /* Interrupt router bus */
(0x07 << 3) | 0x0, /* Interrupt router device */
0xc00, /* IRQs devoted exclusively to PCI usage */
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
arch i386 end
#dir /drivers/si/3114
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE
object get_bus_conf.o
object irq_tables.o
end
if CONFIG_USE_INIT
makerule ./cache_as_ram_auto.o
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
end
else
makerule ./cache_as_ram_auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
end
device pci 2.0 on end # USB 0x0223
device pci 2.1 on end # USB
device pci 2.2 on end # USB
- #when HT_CHAIN_END_UNITID_BASE (0,1) < HT_CHAIN_UNITID_BASE (6,,,,),
+ #when CONFIG_HT_CHAIN_END_UNITID_BASE (0,1) < CONFIG_HT_CHAIN_UNITID_BASE (6,,,,),
chip drivers/pci/onboard
device pci 4.0 on end # it is in bcm5785_0 bus, but the device id can not be changed even unitid is changed, fake one to get the rom_address
- # if HT_CHAIN_END_UNITID_BASE=0, it is 5, if HT_CHAIN_END_UNITID_BASE=1, it is 4
+ # if CONFIG_HT_CHAIN_END_UNITID_BASE=0, it is 5, if CONFIG_HT_CHAIN_END_UNITID_BASE=1, it is 4
register "rom_address" = "0xfff80000"
end
end
- #when HT_CHAIN_END_UNITID_BASE > HT_CHAIN_UNITID_BASE (6, ,,,,)
+ #when CONFIG_HT_CHAIN_END_UNITID_BASE > CONFIG_HT_CHAIN_UNITID_BASE (6, ,,,,)
# chip drivers/pci/onboard
# device pci 0.0 on end # fake, will be disabled
# end
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses HAVE_ACPI_TABLES
-uses HAVE_ACPI_RESUME
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_HAVE_ACPI_TABLES
+uses CONFIG_HAVE_ACPI_RESUME
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_MAX_CPUS
uses CONFIG_MAX_PHYSICAL_CPUS
uses CONFIG_LOGICAL_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
-uses _RAMBASE
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_RAMBASE
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_SERIAL8250
-uses HAVE_INIT_TIMER
+uses CONFIG_HAVE_INIT_TIMER
uses CONFIG_GDB_STUB
uses CONFIG_GDB_STUB
-uses CROSS_COMPILE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
-uses HW_MEM_HOLE_SIZEK
-uses HT_CHAIN_UNITID_BASE
-uses HT_CHAIN_END_UNITID_BASE
-uses SB_HT_CHAIN_ON_BUS0
-
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
+uses CONFIG_HW_MEM_HOLE_SIZEK
+uses CONFIG_HT_CHAIN_UNITID_BASE
+uses CONFIG_HT_CHAIN_END_UNITID_BASE
+uses CONFIG_SB_HT_CHAIN_ON_BUS0
+
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
uses CONFIG_USE_INIT
uses CONFIG_USE_PRINTK_IN_CAR
-uses SB_HT_CHAIN_UNITID_OFFSET_ONLY
+uses CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY
###
### Build options
###
##
-## ROM_SIZE is the size of boot ROM that this board will use.
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
##
-default ROM_SIZE=524288
+default CONFIG_ROM_SIZE=524288
##
-## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
+## CONFIG_FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
##
-#default FALLBACK_SIZE=131072
+#default CONFIG_FALLBACK_SIZE=131072
#256K
-default FALLBACK_SIZE=0x40000
+default CONFIG_FALLBACK_SIZE=0x40000
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=11
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=11
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
##
## Move the default coreboot cmos range off of AMD RTC registers
##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
+default CONFIG_LB_CKS_RANGE_START=49
+default CONFIG_LB_CKS_RANGE_END=122
+default CONFIG_LB_CKS_LOC=123
##
## Build code for SMP support
default CONFIG_LOGICAL_CPUS=1
#1G memory hole
-default HW_MEM_HOLE_SIZEK=0x100000
+default CONFIG_HW_MEM_HOLE_SIZEK=0x100000
#VGA Console
#default CONFIG_CONSOLE_VGA=1
#default CONFIG_PCI_ROM_RUN=1
#HT Unit ID offset
-default HT_CHAIN_UNITID_BASE=0x6
+default CONFIG_HT_CHAIN_UNITID_BASE=0x6
#real SB Unit ID
-default HT_CHAIN_END_UNITID_BASE=0x1
+default CONFIG_HT_CHAIN_END_UNITID_BASE=0x1
#make the SB HT chain on bus 0
-default SB_HT_CHAIN_ON_BUS0=1
+default CONFIG_SB_HT_CHAIN_ON_BUS0=1
##
## enable CACHE_AS_RAM specifics
##
-default USE_DCACHE_RAM=1
-default DCACHE_RAM_BASE=0xcf000
-default DCACHE_RAM_SIZE=0x1000
+default CONFIG_USE_DCACHE_RAM=1
+default CONFIG_DCACHE_RAM_BASE=0xcf000
+default CONFIG_DCACHE_RAM_SIZE=0x1000
default CONFIG_USE_INIT=0
##
##
## Clean up the motherboard id strings
##
-default MAINBOARD_PART_NUMBER="blast"
-default MAINBOARD_VENDOR="Broadcom"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x161f
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x3050
+default CONFIG_MAINBOARD_PART_NUMBER="blast"
+default CONFIG_MAINBOARD_VENDOR="Broadcom"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x161f
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x3050
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE=0x4000
+default CONFIG_HEAP_SIZE=0x4000
##
## Only use the option table in a normal image
##
-default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
##
## Coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00004000
+default CONFIG_RAMBASE=0x00004000
##
## Load the payload from the ROM
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## Disable the gdb stub by default
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
### End Options.lb
#
#include "cpu/amd/model_fxx/init_cpus.c"
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
#include "northbridge/amd/amdk8/early_ht.c"
// post_code(0x25);
;
}
-#endif /* USE_FALLBACK_IMAGE == 1 */
+#endif /* CONFIG_USE_FALLBACK_IMAGE == 1 */
void real_main(unsigned long bist, unsigned long cpu_init_detectedx);
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
failover_process(bist, cpu_init_detectedx);
#endif
real_main(bist, cpu_init_detectedx);
}
// post_code(0x32);
- pc87417_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ pc87417_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
// post_code(0x33);
uart_init();
dev = dev_find_slot(bus_bcm5785_1, PCI_DEVFN(0x0d,0));
if(dev) {
bus_bcm5785_1_1 = pci_read_config8(dev, PCI_SECONDARY_BUS);
-#if HT_CHAIN_END_UNITID_BASE >= HT_CHAIN_UNITID_BASE
+#if CONFIG_HT_CHAIN_END_UNITID_BASE >= CONFIG_HT_CHAIN_UNITID_BASE
bus_isa = pci_read_config8(dev, PCI_SUBORDINATE_BUS);
bus_isa++;
// printk_debug("bus_isa=%d\n",bus_isa);
dev = dev_find_slot(bus_bcm5780[0], PCI_DEVFN(sbdn2 + i - 1,0));
if(dev) {
bus_bcm5780[i] = pci_read_config8(dev, PCI_SECONDARY_BUS);
-#if HT_CHAIN_END_UNITID_BASE < HT_CHAIN_UNITID_BASE
+#if CONFIG_HT_CHAIN_END_UNITID_BASE < CONFIG_HT_CHAIN_UNITID_BASE
bus_isa = pci_read_config8(dev, PCI_SUBORDINATE_BUS);
bus_isa++;
// printk_debug("bus_isa=%d\n",bus_isa);
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
arch i386 end
driver mainboard.o
-if HAVE_PIRQ_TABLE
+if CONFIG_HAVE_PIRQ_TABLE
object irq_tables.o
end
makerule ./failover.E
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -E -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -E -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./auto.E
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -E -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -E -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
mainboardinit cpu/x86/16bit/entry16.inc
mainboardinit cpu/x86/32bit/entry32.inc
ldscript /cpu/x86/16bit/entry16.lds
ldscript /cpu/x86/32bit/entry32.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
mainboardinit arch/i386/lib/cpu_reset.inc
mainboardinit arch/i386/lib/id.inc
ldscript /arch/i386/lib/id.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_ROM_PAYLOAD
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses HAVE_MP_TABLE
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
-default ROM_SIZE = 256 * 1024
-default HAVE_FALLBACK_BOOT = 1
-default HAVE_MP_TABLE = 0
-default HAVE_HARD_RESET = 0
+default CONFIG_ROM_SIZE = 256 * 1024
+default CONFIG_HAVE_FALLBACK_BOOT = 1
+default CONFIG_HAVE_MP_TABLE = 0
+default CONFIG_HAVE_HARD_RESET = 0
default CONFIG_UDELAY_TSC = 1
default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 1
-default HAVE_PIRQ_TABLE = 1
-default IRQ_SLOT_COUNT = 0 # Override this in targets/*/Config.lb.
-default MAINBOARD_VENDOR = "N/A" # Override this in targets/*/Config.lb.
-default MAINBOARD_PART_NUMBER = "N/A" # Override this in targets/*/Config.lb.
-default ROM_IMAGE_SIZE = 64 * 1024
-default FALLBACK_SIZE = 128 * 1024
-default STACK_SIZE = 8 * 1024
-default HEAP_SIZE = 16 * 1024
-default HAVE_OPTION_TABLE = 0
-#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_HAVE_PIRQ_TABLE = 1
+default CONFIG_IRQ_SLOT_COUNT = 0 # Override this in targets/*/Config.lb.
+default CONFIG_MAINBOARD_VENDOR = "N/A" # Override this in targets/*/Config.lb.
+default CONFIG_MAINBOARD_PART_NUMBER = "N/A" # Override this in targets/*/Config.lb.
+default CONFIG_ROM_IMAGE_SIZE = 64 * 1024
+default CONFIG_FALLBACK_SIZE = 128 * 1024
+default CONFIG_STACK_SIZE = 8 * 1024
+default CONFIG_HEAP_SIZE = 16 * 1024
+default CONFIG_HAVE_OPTION_TABLE = 0
+#default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 0
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
-default CROSS_COMPILE = ""
-default CC = "$(CROSS_COMPILE)gcc -m32"
-default HOSTCC = "gcc"
+default CONFIG_CROSS_COMPILE = ""
+default CC = "$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC = "gcc"
default CONFIG_CONSOLE_SERIAL8250 = 1
-default TTYS0_BAUD = 115200
-default TTYS0_BASE = 0x3f8
-default TTYS0_LCS = 0x3 # 8n1
-default DEFAULT_CONSOLE_LOGLEVEL = 9
-default MAXIMUM_CONSOLE_LOGLEVEL = 9
+default CONFIG_TTYS0_BAUD = 115200
+default CONFIG_TTYS0_BASE = 0x3f8
+default CONFIG_TTYS0_LCS = 0x3 # 8n1
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
default CONFIG_CONSOLE_VGA = 1
default CONFIG_PCI_ROM_RUN = 1
early_mtrr_init();
/* FIXME: Should be PC97307! */
- pc97317_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ pc97317_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
report_bist_failure(bist);
const struct irq_routing_table intel_irq_routing_table = {
PIRQ_SIGNATURE,
PIRQ_VERSION,
- 32 + 16 * IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
+ 32 + 16 * CONFIG_IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
0x00, /* Interrupt router bus */
(0x14 << 3) | 0x0, /* Interrupt router device */
0, /* IRQs devoted exclusively to PCI usage */
##
## Only use the option table in a normal image
##
-default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 128 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 128 * 1024
include /config/nofailovercalculation.lb
##
##
driver mainboard.o
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
object reset.o
##
## Romcc output
##
makerule ./failover.E
- depends "$(MAINBOARD)/failover.c ../romcc"
- action "../romcc -fno-simplify-phi -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/failover.c ../romcc"
+ action "../romcc -fno-simplify-phi -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/failover.c ../romcc"
- action "../romcc -fno-simplify-phi -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/failover.c ../romcc"
+ action "../romcc -fno-simplify-phi -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/failover.c -o $@"
end
makerule ./auto.E
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -fno-simplify-phi -E -mcpu=p4 -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -fno-simplify-phi -E -mcpu=p4 -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -fno-simplify-phi -mcpu=p4 -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -fno-simplify-phi -mcpu=p4 -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
##
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_LOGICAL_CPUS
uses CONFIG_MAX_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
-uses _RAMBASE
+uses CONFIG_RAMBASE
uses CONFIG_GDB_STUB
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_BTEXT
uses CC
-uses HOSTCC
-uses CROSS_COMPILE
-uses OBJCOPY
+uses CONFIG_HOSTCC
+uses CONFIG_CROSS_COMPILE
+uses CONFIG_OBJCOPY
###
###
##
-## ROM_SIZE is the size of boot ROM that this board will use.
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
##
-default ROM_SIZE=1048576
+default CONFIG_ROM_SIZE=1048576
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## Delay timer options
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=16
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=16
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
##
## Move the default coreboot cmos range off of AMD RTC registers
##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
+default CONFIG_LB_CKS_RANGE_START=49
+default CONFIG_LB_CKS_RANGE_END=122
+default CONFIG_LB_CKS_LOC=123
##
## Build code for SMP support
##
## Clean up the motherboard id strings
##
-default MAINBOARD_PART_NUMBER="X6DHR"
-default MAINBOARD_VENDOR= "Supermicro"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x15D9
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x5580
+default CONFIG_MAINBOARD_PART_NUMBER="X6DHR"
+default CONFIG_MAINBOARD_VENDOR= "Supermicro"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x15D9
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x5580
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 32K heap
##
-default HEAP_SIZE=0x8000
+default CONFIG_HEAP_SIZE=0x8000
###
### Compute the location and size of where this firmware image
### (coreboot plus bootloader) will live in the boot rom chip.
###
-default FALLBACK_SIZE=131072
+default CONFIG_FALLBACK_SIZE=131072
##
## Coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00004000
+default CONFIG_RAMBASE=0x00004000
##
## Load the payload from the ROM
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## Disable the gdb stub by default
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
##
## Don't enable the btext console
outb(0x87,0x2e);
outb(0x87,0x2e);
pnp_write_config(CONSOLE_SERIAL_DEV, 0x24, 0x84 | (1 << 6));
- w83627hf_enable_dev(CONSOLE_SERIAL_DEV, TTYS0_BASE);
+ w83627hf_enable_dev(CONSOLE_SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
##
##
driver mainboard.o
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
#object reset.o
##
## Romcc output
##
makerule ./failover.E
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./auto.E
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -E -mcpu=p3 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -E -mcpu=p3 -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -mcpu=p3 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -mcpu=p3 -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
##
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_ROM_PAYLOAD
uses CONFIG_UDELAY_IO
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses HAVE_MP_TABLE
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-default DEFAULT_CONSOLE_LOGLEVEL=9
-default MAXIMUM_CONSOLE_LOGLEVEL=9
-## ROM_SIZE is the size of boot ROM that this board will use.
-default ROM_SIZE = 1024*1024
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=9
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=9
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
+default CONFIG_ROM_SIZE = 1024*1024
###
### Build options
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## no MP table
##
-default HAVE_MP_TABLE=0
+default CONFIG_HAVE_MP_TABLE=0
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
##
## use io based udelay function
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=5
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=5
#object irq_tables.o
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
-default FALLBACK_SIZE = 131072
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
+default CONFIG_FALLBACK_SIZE = 131072
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE=0x4000
+default CONFIG_HEAP_SIZE=0x4000
##
## Only use the option table in a normal image
##
-#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
+#default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
#endif
}
- w83627hf_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ w83627hf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
-default ROM_SIZE = 512 * 1024
-default FALLBACK_SIZE = 0x10000
+default CONFIG_ROM_SIZE = 512 * 1024
+default CONFIG_FALLBACK_SIZE = 0x10000
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 32 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 32 * 1024
include /config/nofailovercalculation.lb
##
##
driver mainboard.o
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
# object reset.o
##
## Romcc output
##
makerule ./failover.E
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./auto.E
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -E -mcpu=i386 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -E -mcpu=i386 -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -mcpu=i386 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -mcpu=i386 -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
##
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_COMPRESS
uses CONFIG_ROM_PAYLOAD
uses CONFIG_USE_INIT
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses HAVE_MP_TABLE
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
uses CONFIG_CONSOLE_SERIAL8250
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
# VGA support
uses CONFIG_CONSOLE_VGA
default CONFIG_CONSOLE_SERIAL8250=1
-default DEFAULT_CONSOLE_LOGLEVEL=9
-default MAXIMUM_CONSOLE_LOGLEVEL=9
-## ROM_SIZE is the size of boot ROM that this board will use.
-default ROM_SIZE = 256*1024
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=9
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=9
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
+default CONFIG_ROM_SIZE = 256*1024
###
### Build options
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## no MP table
##
-default HAVE_MP_TABLE=0
+default CONFIG_HAVE_MP_TABLE=0
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=0
+default CONFIG_HAVE_HARD_RESET=0
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=7
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=7
#object irq_tables.o
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
-default FALLBACK_SIZE = 131072
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
+default CONFIG_FALLBACK_SIZE = 131072
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE=0x4000
+default CONFIG_HEAP_SIZE=0x4000
##
## Only use the option table in a normal image
##
-#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
+#default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
/* hack for IDIOTIC need to fix rom_start */
printk_err("Patching rom_start due to sc520 limits\n");
rom_start = 0x2000000 + 0x40000;
- rom_end = rom_start + PAYLOAD_SIZE - 1;
+ rom_end = rom_start + CONFIG_PAYLOAD_SIZE - 1;
}
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
##
driver mainboard.o
-if HAVE_PIRQ_TABLE
+if CONFIG_HAVE_PIRQ_TABLE
object irq_tables.o
end
#compile cache_as_ram.c to auto.inc
makerule ./cache_as_ram_auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
# mainboardinit ./failover.inc
end
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_ROM_PAYLOAD
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_NRV2B
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses HAVE_MP_TABLE
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
uses CONFIG_VIDEO_MB
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
uses CONFIG_USE_PRINTK_IN_CAR
-uses PIRQ_ROUTE
+uses CONFIG_PIRQ_ROUTE
-## ROM_SIZE is the size of boot ROM that this board will use.
-default ROM_SIZE = 256*1024
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
+default CONFIG_ROM_SIZE = 256*1024
###
### Build options
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## no MP table
##
-default HAVE_MP_TABLE=0
+default CONFIG_HAVE_MP_TABLE=0
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=0
+default CONFIG_HAVE_HARD_RESET=0
## Delay timer options
##
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=6
-default PIRQ_ROUTE=1
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=6
+default CONFIG_PIRQ_ROUTE=1
#object irq_tables.o
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=0
+default CONFIG_HAVE_OPTION_TABLE=0
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
-default FALLBACK_SIZE = 131072
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
+default CONFIG_FALLBACK_SIZE = 131072
##
## enable CACHE_AS_RAM specifics
##
-default USE_DCACHE_RAM=1
-default DCACHE_RAM_BASE=0xc8000
-default DCACHE_RAM_SIZE=0x08000
+default CONFIG_USE_DCACHE_RAM=1
+default CONFIG_DCACHE_RAM_BASE=0xc8000
+default CONFIG_DCACHE_RAM_SIZE=0x08000
default CONFIG_USE_PRINTK_IN_CAR=1
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE=0x4000
+default CONFIG_HEAP_SIZE=0x4000
##
## Only use the option table in a normal image
##
-#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
+#default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
##
## The default compiler
##
-default CROSS_COMPILE=""
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CONFIG_CROSS_COMPILE=""
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## The Serial Console
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
#
* for cs5536
*/
cs5536_disable_internal_uart();
- w83627hf_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ w83627hf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
mb_gpio_init();
uart_init();
console_init();
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
##
driver mainboard.o
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
#object reset.o
##
## Romcc output
##
makerule ./failover.E
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./auto.E
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -E -mcpu=i386 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -E -mcpu=i386 -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -mcpu=i386 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -mcpu=i386 -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
##
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_ROM_PAYLOAD
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses HAVE_MP_TABLE
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
uses CONFIG_VIDEO_MB
-uses PIRQ_ROUTE
+uses CONFIG_PIRQ_ROUTE
-## ROM_SIZE is the size of boot ROM that this board will use.
-default ROM_SIZE = 256*1024
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
+default CONFIG_ROM_SIZE = 256*1024
###
### Build options
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## no MP table
##
-default HAVE_MP_TABLE=0
+default CONFIG_HAVE_MP_TABLE=0
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=0
+default CONFIG_HAVE_HARD_RESET=0
## Delay timer options
##
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=2
-default PIRQ_ROUTE=1
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=2
+default CONFIG_PIRQ_ROUTE=1
#object irq_tables.o
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=0
+default CONFIG_HAVE_OPTION_TABLE=0
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
-default FALLBACK_SIZE = 131072
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
+default CONFIG_FALLBACK_SIZE = 131072
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE=0x4000
+default CONFIG_HEAP_SIZE=0x4000
##
## Only use the option table in a normal image
##
-#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
+#default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
##
## The default compiler
##
-default CROSS_COMPILE=""
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CONFIG_CROSS_COMPILE=""
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## The Serial Console
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
default CONFIG_VIDEO_MB = 0
static void main(unsigned long bist)
{
- pc97317_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ pc97317_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
## Build the objects we have code for in this directory.
##
-addaction coreboot.a "$(CROSS_COMPILE)ranlib coreboot.a"
+addaction coreboot.a "$(CONFIG_CROSS_COMPILE)ranlib coreboot.a"
makedefine CFLAGS += -msoft-float
## Config file for the Embedded Planet EP405PC Computing Engine
##
-uses PCIC0_CFGADDR
+uses CONFIG_PCIC0_CFGADDR
uses CONFIG_CBFS
uses CONFIG_ARCH_X86
-uses PCIC0_CFGDATA
-uses ISA_IO_BASE
-uses ISA_MEM_BASE
-uses TTYS0_BASE
-uses _IO_BASE
-
-uses CPU_OPT
-uses CROSS_COMPILE
-uses HAVE_OPTION_TABLE
+uses CONFIG_PCIC0_CFGDATA
+uses CONFIG_ISA_IO_BASE
+uses CONFIG_ISA_MEM_BASE
+uses CONFIG_TTYS0_BASE
+uses CONFIG_IO_BASE
+
+uses CONFIG_CPU_OPT
+uses CONFIG_CROSS_COMPILE
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_COMPRESS
uses CONFIG_CHIP_CONFIGURE
-uses DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
uses CONFIG_USE_INIT
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD TTYS0_DIV
-uses NO_POST
+uses CONFIG_TTYS0_BAUD CONFIG_TTYS0_DIV
+uses CONFIG_NO_POST
uses CONFIG_IDE
uses CONFIG_FS_PAYLOAD
uses CONFIG_FS_EXT2
uses CONFIG_FS_FAT
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses AUTOBOOT_CMDLINE
+uses CONFIG_AUTOBOOT_CMDLINE
uses CONFIG_SYS_CLK_FREQ
-uses IDE_BOOT_DRIVE
-#uses IDE_SWAB
-uses IDE_OFFSET
-uses ROM_SIZE
-uses ROM_IMAGE_SIZE
-uses _RESET
-uses _EXCEPTION_VECTORS
-uses _ROMBASE
-uses _ROMSTART
-uses _RAMBASE
-#uses _RAMSTART
-uses EMBEDDED_RAM_SIZE
-uses STACK_SIZE HEAP_SIZE
-
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IDE_BOOT_DRIVE
+#uses CONFIG_IDE_SWAB
+uses CONFIG_IDE_OFFSET
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_RESET
+uses CONFIG_EXCEPTION_VECTORS
+uses CONFIG_ROMBASE
+uses CONFIG_ROMSTART
+uses CONFIG_RAMBASE
+#uses CONFIG_RAMSTART
+uses CONFIG_EMBEDDED_RAM_SIZE
+uses CONFIG_STACK_SIZE CONFIG_HEAP_SIZE
+
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses CROSS_COMPILE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
##
## Set PCI configuration register addresses
##
-default PCIC0_CFGADDR=0xeec00000
-default PCIC0_CFGDATA=0xeec00004
+default CONFIG_PCIC0_CFGADDR=0xeec00000
+default CONFIG_PCIC0_CFGDATA=0xeec00004
##
## Set PCI/ISA I/O and memory base address
##
-default ISA_IO_BASE=0xe8000000
-default ISA_MEM_BASE=0x80000000
-default _IO_BASE=ISA_IO_BASE
+default CONFIG_ISA_IO_BASE=0xe8000000
+default CONFIG_ISA_MEM_BASE=0x80000000
+default CONFIG_IO_BASE=CONFIG_ISA_IO_BASE
##
## HACK ALERT: the UART0 registers are not in the PCI I/O address space
## but both IDE and UART use the same routines for I/O (inb/outb). To get
## around this we set TTYSO_BASE to the difference between the two.
##
-default TTYS0_BASE=0xef600300-ISA_IO_BASE
+default CONFIG_TTYS0_BASE=0xef600300-CONFIG_ISA_IO_BASE
## Enable PPC405 instructions
-default CPU_OPT="-mcpu=405"
-#default CPU_OPT=""
+default CONFIG_CPU_OPT="-mcpu=405"
+#default CONFIG_CPU_OPT=""
default CONFIG_ARCH_X86=0
## Use stage 1 initialization code
default CONFIG_COMPRESS=0
## Turn off POST codes
-default NO_POST=1
+default CONFIG_NO_POST=1
## Enable serial console
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
default CONFIG_CONSOLE_SERIAL8250=1
# Divisor of 69 == 9600 baud due to weird clocking
-default TTYS0_DIV=69
-default TTYS0_BAUD=9600
+default CONFIG_TTYS0_DIV=69
+default CONFIG_TTYS0_BAUD=9600
## Boot linux from IDE
default CONFIG_IDE=1
default CONFIG_FS_EXT2=1
default CONFIG_FS_ISO9660=1
default CONFIG_FS_FAT=1
-default AUTOBOOT_CMDLINE="hda1:/vmlinuz"
+default CONFIG_AUTOBOOT_CMDLINE="hda1:/vmlinuz"
-default ROM_SIZE=1048576
+default CONFIG_ROM_SIZE=1048576
## Board has fixed size RAM
-default EMBEDDED_RAM_SIZE=64*1024*1024
+default CONFIG_EMBEDDED_RAM_SIZE=64*1024*1024
## Coreboot C code runs at this location in RAM
-default _RAMBASE=0x00100000
+default CONFIG_RAMBASE=0x00100000
##
## Use a 64K stack
##
-default STACK_SIZE=0x10000
+default CONFIG_STACK_SIZE=0x10000
##
## Use a 64K heap
##
-default HEAP_SIZE=0x10000
+default CONFIG_HEAP_SIZE=0x10000
##
## System clock
default CONFIG_SYS_CLK_FREQ=33
##
-default _ROMBASE=0xfff00000
+default CONFIG_ROMBASE=0xfff00000
## Reset vector address
-default _RESET=0xfffffffc
+default CONFIG_RESET=0xfffffffc
## Exception vectors
-default _EXCEPTION_VECTORS=_ROMBASE+0x100
+default CONFIG_EXCEPTION_VECTORS=CONFIG_ROMBASE+0x100
## coreboot ROM start address
-default _ROMSTART=0xfff03000
+default CONFIG_ROMSTART=0xfff03000
## coreboot C code runs at this location in RAM
-default _RAMBASE=0x00100000
+default CONFIG_RAMBASE=0x00100000
### End Options.lb
#
-## we don't use USE_DCACHE_RAM by default
-default USE_DCACHE_RAM=0
+## we don't use CONFIG_USE_DCACHE_RAM by default
+default CONFIG_USE_DCACHE_RAM=0
##
## Compute the location and size of where this firmware image
## (coreboot plus bootloader) will live in the boot rom chip.
##
-default ROM_SIZE = 256 * 1024
-default ROM_SECTION_SIZE = ROM_IMAGE_SIZE
-default ROM_SECTION_OFFSET = 0
+default CONFIG_ROM_SIZE = 256 * 1024
+default CONFIG_ROM_SECTION_SIZE = CONFIG_ROM_IMAGE_SIZE
+default CONFIG_ROM_SECTION_OFFSET = 0
##
## Compute the start location and size size of
## The coreboot bootloader.
##
-default PAYLOAD_SIZE = ( ROM_SIZE - ROM_IMAGE_SIZE )
-default CONFIG_ROM_PAYLOAD_START = (0xffffffff - ROM_SIZE + ROM_SECTION_OFFSET + 1)
+default CONFIG_PAYLOAD_SIZE = ( CONFIG_ROM_SIZE - CONFIG_ROM_IMAGE_SIZE )
+default CONFIG_ROM_PAYLOAD_START = (0xffffffff - CONFIG_ROM_SIZE + CONFIG_ROM_SECTION_OFFSET + 1)
##
## Compute where this copy of coreboot will start in the boot rom
##
-default _ROMBASE = ( CONFIG_ROM_PAYLOAD_START + PAYLOAD_SIZE )
+default CONFIG_ROMBASE = ( CONFIG_ROM_PAYLOAD_START + CONFIG_PAYLOAD_SIZE )
##
## Compute a range of ROM that can cached to speed up coreboot,
## execution speed.
##
-## XIP_ROM_SIZE must be a power of 2.
-## XIP_ROM_BASE must be a multiple of XIP_ROM_SIZE
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+## CONFIG_XIP_ROM_BASE must be a multiple of CONFIG_XIP_ROM_SIZE
##
-default XIP_ROM_SIZE=32*1024
-default XIP_ROM_BASE = ( _ROMBASE + ROM_IMAGE_SIZE - XIP_ROM_SIZE )
+default CONFIG_XIP_ROM_SIZE=32*1024
+default CONFIG_XIP_ROM_BASE = ( CONFIG_ROMBASE + CONFIG_ROM_IMAGE_SIZE - CONFIG_XIP_ROM_SIZE )
##
## Set all of the defaults for an x86 architecture
##
driver mainboard.o
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
#object reset.o
-## ALL dependencies for USE_DCACHE_RAM go here.
+## ALL dependencies for CONFIG_USE_DCACHE_RAM go here.
## That way, later, we can simply yank them if we wish.
-## We include the old-fashioned entry code in the ! USE_DCACHE_RAM case.
+## We include the old-fashioned entry code in the ! CONFIG_USE_DCACHE_RAM case.
## we do not use failover yet in this case. This is a work in progress.
-if USE_DCACHE_RAM
+if CONFIG_USE_DCACHE_RAM
##
##
mainboardinit arch/i386/init/entry.S
## Romcc output
##
makerule ./failover.E
- depends "$(MAINBOARD)/failover.c ../romcc"
- action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/failover.c ../romcc"
+ action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/failover.c ../romcc"
- action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/failover.c ../romcc"
+ action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/failover.c -o $@"
end
makerule ./auto.E
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -E -mcpu=i386 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -E -mcpu=i386 -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -mcpu=i386 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -mcpu=i386 -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
##
ldscript /arch/i386/lib/id.lds
##
-## end of USE_DCACHE_RAM bits.
+## end of CONFIG_USE_DCACHE_RAM bits.
##
end
-uses HAVE_MP_TABLE
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_COMPRESS
uses CONFIG_COMPRESSED_PAYLOAD_NRV2B
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
uses CONFIG_ROM_PAYLOAD
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses HAVE_MP_TABLE
-uses HAVE_HIGH_TABLES
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_HAVE_HIGH_TABLES
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
uses CONFIG_PCI_ROM_RUN
uses CONFIG_PCI_OPTION_ROM_RUN_REALMODE
uses CONFIG_CONSOLE_SERIAL8250
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
uses CONFIG_USE_INIT
uses CONFIG_USE_PRINTK_IN_CAR
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CBFS
default CONFIG_CONSOLE_SERIAL8250=1
-default DEFAULT_CONSOLE_LOGLEVEL=8
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
default CONFIG_CBFS=1
-## ROM_SIZE is the size of boot ROM that this board will use.
-default ROM_SIZE = 256*1024
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
+default CONFIG_ROM_SIZE = 256*1024
###
### Build options
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## no MP table
##
-default HAVE_MP_TABLE=0
+default CONFIG_HAVE_MP_TABLE=0
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=0
+default CONFIG_HAVE_HARD_RESET=0
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=6
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=6
-default HAVE_HIGH_TABLES=1
+default CONFIG_HAVE_HIGH_TABLES=1
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
##
## Option ROM init
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
-default FALLBACK_SIZE = ROM_IMAGE_SIZE
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
+default CONFIG_FALLBACK_SIZE = CONFIG_ROM_IMAGE_SIZE
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE=0x4000
+default CONFIG_HEAP_SIZE=0x4000
##
## Only use the option table in a normal image
##
-#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
+#default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## known-good settings for qemu
-default DCACHE_RAM_BASE=0x8f000
-default DCACHE_RAM_SIZE=0x1000
+default CONFIG_DCACHE_RAM_BASE=0x8f000
+default CONFIG_DCACHE_RAM_SIZE=0x1000
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
arch i386 end
driver mainboard.o
-if HAVE_PIRQ_TABLE
+if CONFIG_HAVE_PIRQ_TABLE
object irq_tables.o
end
makerule ./failover.E
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -E -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -E -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./auto.E
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -E -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -E -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
mainboardinit cpu/x86/16bit/entry16.inc
mainboardinit cpu/x86/32bit/entry32.inc
ldscript /cpu/x86/16bit/entry16.lds
ldscript /cpu/x86/32bit/entry32.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
mainboardinit arch/i386/lib/cpu_reset.inc
mainboardinit arch/i386/lib/id.inc
ldscript /arch/i386/lib/id.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_ROM_PAYLOAD
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses HAVE_MP_TABLE
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
-default ROM_SIZE = 256 * 1024
-default HAVE_FALLBACK_BOOT = 1
-default HAVE_MP_TABLE = 0
-default HAVE_HARD_RESET = 0
+default CONFIG_ROM_SIZE = 256 * 1024
+default CONFIG_HAVE_FALLBACK_BOOT = 1
+default CONFIG_HAVE_MP_TABLE = 0
+default CONFIG_HAVE_HARD_RESET = 0
default CONFIG_UDELAY_TSC = 1
default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 1
-default HAVE_PIRQ_TABLE = 1
-default IRQ_SLOT_COUNT = 0 # Override this in targets/*/Config.lb.
-default MAINBOARD_VENDOR = "N/A" # Override this in targets/*/Config.lb.
-default MAINBOARD_PART_NUMBER = "N/A" # Override this in targets/*/Config.lb.
-default ROM_IMAGE_SIZE = 64 * 1024
-default FALLBACK_SIZE = 128 * 1024
-default STACK_SIZE = 8 * 1024
-default HEAP_SIZE = 16 * 1024
-default HAVE_OPTION_TABLE = 0
-#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_HAVE_PIRQ_TABLE = 1
+default CONFIG_IRQ_SLOT_COUNT = 0 # Override this in targets/*/Config.lb.
+default CONFIG_MAINBOARD_VENDOR = "N/A" # Override this in targets/*/Config.lb.
+default CONFIG_MAINBOARD_PART_NUMBER = "N/A" # Override this in targets/*/Config.lb.
+default CONFIG_ROM_IMAGE_SIZE = 64 * 1024
+default CONFIG_FALLBACK_SIZE = 128 * 1024
+default CONFIG_STACK_SIZE = 8 * 1024
+default CONFIG_HEAP_SIZE = 16 * 1024
+default CONFIG_HAVE_OPTION_TABLE = 0
+#default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 0
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
-default CROSS_COMPILE = ""
-default CC = "$(CROSS_COMPILE)gcc -m32"
-default HOSTCC = "gcc"
+default CONFIG_CROSS_COMPILE = ""
+default CC = "$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC = "gcc"
default CONFIG_CONSOLE_SERIAL8250 = 1
-default TTYS0_BAUD = 115200
-default TTYS0_BASE = 0x3f8
-default TTYS0_LCS = 0x3 # 8n1
-default DEFAULT_CONSOLE_LOGLEVEL = 9
-default MAXIMUM_CONSOLE_LOGLEVEL = 9
+default CONFIG_TTYS0_BAUD = 115200
+default CONFIG_TTYS0_BASE = 0x3f8
+default CONFIG_TTYS0_LCS = 0x3 # 8n1
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
default CONFIG_CONSOLE_VGA = 1
default CONFIG_PCI_ROM_RUN = 1
if (bist == 0)
early_mtrr_init();
- it8671f_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ it8671f_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
report_bist_failure(bist);
const struct irq_routing_table intel_irq_routing_table = {
PIRQ_SIGNATURE,
PIRQ_VERSION,
- 32 + 16 * IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
+ 32 + 16 * CONFIG_IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
0x00, /* Interrupt router bus */
(0x07 << 3) | 0x0, /* Interrupt router device */
0xc00, /* IRQs devoted exclusively to PCI usage */
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/failovercalculation.lb
arch i386 end
#needed by irq_tables and mptable and acpi_tables
object get_bus_conf.o
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
#object reset.o
if CONFIG_USE_INIT
makerule ./cache_as_ram_auto.o
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
end
else
makerule ./cache_as_ram_auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CPU_OPT) $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_CPU_OPT) $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
end
-if USE_FAILOVER_IMAGE
+if CONFIG_USE_FAILOVER_IMAGE
else
if CONFIG_AP_CODE_IN_CAR
makerule ./apc_auto.o
- depends "$(MAINBOARD)/apc_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/apc_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/apc_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/apc_auto.c -o $@"
end
ldscript /arch/i386/init/ldscript_apc.lb
end
##
## Build our 16 bit and 32 bit coreboot entry code
##
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
end
##
## Build our reset vector (This is where coreboot is entered)
##
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
ldscript /cpu/x86/32bit/reset32.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
##
## ROMSTRAP table for MCP55
##
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
mainboardinit southbridge/sis/sis966/romstrap.inc
ldscript /southbridge/sis/sis966/romstrap.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
mainboardinit southbridge/sis/sis966/romstrap.inc
ldscript /southbridge/sis/sis966/romstrap.lds
end
### Things are delicate and we test to see if we should
### failover to another image.
###
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
ldscript /arch/i386/lib/failover_failover.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
end
end
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses HAVE_ACPI_TABLES
-uses HAVE_ACPI_RESUME
-uses ACPI_SSDTX_NUM
-uses USE_FALLBACK_IMAGE
-uses USE_FAILOVER_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_FAILOVER_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_HAVE_ACPI_TABLES
+uses CONFIG_HAVE_ACPI_RESUME
+uses CONFIG_ACPI_SSDTX_NUM
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_USE_FAILOVER_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_FAILOVER_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_MAX_CPUS
uses CONFIG_MAX_PHYSICAL_CPUS
uses CONFIG_LOGICAL_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses FAILOVER_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_FAILOVER_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_NRV2B
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
-uses _RAMBASE
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_RAMBASE
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_SERIAL8250
-uses HAVE_INIT_TIMER
+uses CONFIG_HAVE_INIT_TIMER
uses CONFIG_GDB_STUB
uses CONFIG_GDB_STUB
-uses CROSS_COMPILE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
uses CONFIG_CONSOLE_VGA
uses CONFIG_USBDEBUG_DIRECT
uses CONFIG_PCI_ROM_RUN
-uses HW_MEM_HOLE_SIZEK
-uses HW_MEM_HOLE_SIZE_AUTO_INC
-uses K8_HT_FREQ_1G_SUPPORT
-
-uses HT_CHAIN_UNITID_BASE
-uses HT_CHAIN_END_UNITID_BASE
-uses SB_HT_CHAIN_ON_BUS0
-uses SB_HT_CHAIN_UNITID_OFFSET_ONLY
-
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
-uses DCACHE_RAM_GLOBAL_VAR_SIZE
+uses CONFIG_HW_MEM_HOLE_SIZEK
+uses CONFIG_HW_MEM_HOLE_SIZE_AUTO_INC
+uses CONFIG_K8_HT_FREQ_1G_SUPPORT
+
+uses CONFIG_HT_CHAIN_UNITID_BASE
+uses CONFIG_HT_CHAIN_END_UNITID_BASE
+uses CONFIG_SB_HT_CHAIN_ON_BUS0
+uses CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY
+
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
+uses CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE
uses CONFIG_USE_INIT
-uses SERIAL_CPU_INIT
+uses CONFIG_SERIAL_CPU_INIT
-uses ENABLE_APIC_EXT_ID
-uses APIC_ID_OFFSET
-uses LIFT_BSP_APIC_ID
+uses CONFIG_ENABLE_APIC_EXT_ID
+uses CONFIG_APIC_ID_OFFSET
+uses CONFIG_LIFT_BSP_APIC_ID
uses CONFIG_PCI_64BIT_PREF_MEM
uses CONFIG_AP_CODE_IN_CAR
-uses MEM_TRAIN_SEQ
+uses CONFIG_MEM_TRAIN_SEQ
-uses WAIT_BEFORE_CPUS_INIT
+uses CONFIG_WAIT_BEFORE_CPUS_INIT
uses CONFIG_USE_PRINTK_IN_CAR
###
##
-## ROM_SIZE is the size of boot ROM that this board will use.
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
##
-default ROM_SIZE=524288
-#default ROM_SIZE=0x100000
+default CONFIG_ROM_SIZE=524288
+#default CONFIG_ROM_SIZE=0x100000
##
-## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
+## CONFIG_FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
##
-#default FALLBACK_SIZE=131072
-#default FALLBACK_SIZE=0x40000
+#default CONFIG_FALLBACK_SIZE=131072
+#default CONFIG_FALLBACK_SIZE=0x40000
#FALLBACK: 256K-4K
-default FALLBACK_SIZE=0x3f000
+default CONFIG_FALLBACK_SIZE=0x3f000
#FAILOVER: 4K
-default FAILOVER_SIZE=0x01000
+default CONFIG_FAILOVER_SIZE=0x01000
#more 1M for pgtbl
default CONFIG_LB_MEM_TOPK=2048
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
-default HAVE_FAILOVER_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FAILOVER_BOOT=1
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=11
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=11
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=0
+default CONFIG_HAVE_MP_TABLE=0
## ACPI tables will be included
-default HAVE_ACPI_TABLES=0
+default CONFIG_HAVE_ACPI_TABLES=0
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
##
## Move the default coreboot cmos range off of AMD RTC registers
##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
+default CONFIG_LB_CKS_RANGE_START=49
+default CONFIG_LB_CKS_RANGE_END=122
+default CONFIG_LB_CKS_LOC=123
##
## Build code for SMP support
default CONFIG_MAX_PHYSICAL_CPUS=1
default CONFIG_LOGICAL_CPUS=1
-#default SERIAL_CPU_INIT=0
+#default CONFIG_SERIAL_CPU_INIT=0
-default ENABLE_APIC_EXT_ID=0
-default APIC_ID_OFFSET=0x10
-default LIFT_BSP_APIC_ID=1
+default CONFIG_ENABLE_APIC_EXT_ID=0
+default CONFIG_APIC_ID_OFFSET=0x10
+default CONFIG_LIFT_BSP_APIC_ID=1
#memory hole size, 0 mean disable, others will enable the hole, at that case if it is small than mmio_basek, it will use mmio_basek instead.
#2G
-#default HW_MEM_HOLE_SIZEK=0x200000
+#default CONFIG_HW_MEM_HOLE_SIZEK=0x200000
#1G
-default HW_MEM_HOLE_SIZEK=0x100000
+default CONFIG_HW_MEM_HOLE_SIZEK=0x100000
#512M
-#default HW_MEM_HOLE_SIZEK=0x80000
+#default CONFIG_HW_MEM_HOLE_SIZEK=0x80000
#make auto increase hole size to avoid hole_startk equal to basek so as to make some kernel happy
-#default HW_MEM_HOLE_SIZE_AUTO_INC=1
+#default CONFIG_HW_MEM_HOLE_SIZE_AUTO_INC=1
#Opteron K8 1G HT Support
-default K8_HT_FREQ_1G_SUPPORT=1
+default CONFIG_K8_HT_FREQ_1G_SUPPORT=1
#VGA Console
default CONFIG_CONSOLE_VGA=1
#default CONFIG_USBDEBUG_DIRECT=0
#HT Unit ID offset, default is 1, the typical one, 0 mean only one HT device
-default HT_CHAIN_UNITID_BASE=0
+default CONFIG_HT_CHAIN_UNITID_BASE=0
#real SB Unit ID, default is 0x20, mean dont touch it at last
-#default HT_CHAIN_END_UNITID_BASE=0x6
+#default CONFIG_HT_CHAIN_END_UNITID_BASE=0x6
#make the SB HT chain on bus 0, default is not (0)
-default SB_HT_CHAIN_ON_BUS0=2
+default CONFIG_SB_HT_CHAIN_ON_BUS0=2
#only offset for SB chain?, default is yes(1)
-default SB_HT_CHAIN_UNITID_OFFSET_ONLY=0
+default CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY=0
#allow capable device use that above 4G
#default CONFIG_PCI_64BIT_PREF_MEM=1
##
## enable CACHE_AS_RAM specifics
##
-default USE_DCACHE_RAM=1
-default DCACHE_RAM_BASE=0xc8000
-default DCACHE_RAM_SIZE=0x08000
-default DCACHE_RAM_GLOBAL_VAR_SIZE=0x01000
+default CONFIG_USE_DCACHE_RAM=1
+default CONFIG_DCACHE_RAM_BASE=0xc8000
+default CONFIG_DCACHE_RAM_SIZE=0x08000
+default CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE=0x01000
default CONFIG_USE_INIT=0
default CONFIG_AP_CODE_IN_CAR=0
-default MEM_TRAIN_SEQ=2
-default WAIT_BEFORE_CPUS_INIT=0
+default CONFIG_MEM_TRAIN_SEQ=2
+default CONFIG_WAIT_BEFORE_CPUS_INIT=0
##
## Build code to setup a generic IOAPIC
##
## Clean up the motherboard id strings
##
-default MAINBOARD_PART_NUMBER="ga_2761gxdk"
-default MAINBOARD_VENDOR="GIGABYTE"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x1039
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x1234
+default CONFIG_MAINBOARD_PART_NUMBER="ga_2761gxdk"
+default CONFIG_MAINBOARD_VENDOR="GIGABYTE"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x1039
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x1234
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 32K heap
##
-default HEAP_SIZE=0x8000
+default CONFIG_HEAP_SIZE=0x8000
##
## Only use the option table in a normal image
##
-default USE_OPTION_TABLE = (!USE_FALLBACK_IMAGE) && (!USE_FAILOVER_IMAGE )
+default CONFIG_USE_OPTION_TABLE = (!CONFIG_USE_FALLBACK_IMAGE) && (!CONFIG_USE_FAILOVER_IMAGE )
##
## Coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00100000
+default CONFIG_RAMBASE=0x00100000
##
## Load the payload from the ROM
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## Disable the gdb stub by default
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
### End Options.lb
#
void hardwaremain(int ret_addr)
{
- struct sys_info *sysinfo = (DCACHE_RAM_BASE + DCACHE_RAM_SIZE - DCACHE_RAM_GLOBAL_VAR_SIZE); // in CACHE
- struct sys_info *sysinfox = ((CONFIG_LB_MEM_TOPK<<10) - DCACHE_RAM_GLOBAL_VAR_SIZE); // in RAM
+ struct sys_info *sysinfo = (CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE); // in CACHE
+ struct sys_info *sysinfox = ((CONFIG_LB_MEM_TOPK<<10) - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE); // in RAM
struct node_core_id id;
//if we want to wait for core1 done before DQS training, set it to 0
#define K8_SET_FIDVID_CORE0_ONLY 1
-#if K8_REV_F_SUPPORT == 1
+#if CONFIG_K8_REV_F_SUPPORT == 1
#define K8_REV_F_SUPPORT_F0_F1_WORKAROUND 0
#endif
#include "option_table.h"
#include "pc80/mc146818rtc_early.c"
-#if USE_FAILOVER_IMAGE==0
+#if CONFIG_USE_FAILOVER_IMAGE==0
#include "pc80/serial.c"
#include "arch/i386/lib/console.c"
#if CONFIG_USBDEBUG_DIRECT
#include "superio/ite/it8716f/it8716f_early_serial.c"
#include "superio/ite/it8716f/it8716f_early_init.c"
-#if USE_FAILOVER_IMAGE==0
+#if CONFIG_USE_FAILOVER_IMAGE==0
#include "cpu/x86/bist.h"
#endif
-#if ((HAVE_FAILOVER_BOOT==1) && (USE_FAILOVER_IMAGE == 1)) || ((HAVE_FAILOVER_BOOT==0) && (USE_FALLBACK_IMAGE == 1))
+#if ((CONFIG_HAVE_FAILOVER_BOOT==1) && (CONFIG_USE_FAILOVER_IMAGE == 1)) || ((CONFIG_HAVE_FAILOVER_BOOT==0) && (CONFIG_USE_FALLBACK_IMAGE == 1))
#include "southbridge/sis/sis966/sis966_enable_rom.c"
#include "northbridge/amd/amdk8/early_ht.c"
);
fallback_image:
-#if HAVE_FAILOVER_BOOT==1
+#if CONFIG_HAVE_FAILOVER_BOOT==1
__asm__ volatile ("jmp __fallback_image"
: /* outputs */
: "a" (bist), "b" (cpu_init_detectedx) /* inputs */
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
-#if HAVE_FAILOVER_BOOT==1
- #if USE_FAILOVER_IMAGE==1
+#if CONFIG_HAVE_FAILOVER_BOOT==1
+ #if CONFIG_USE_FAILOVER_IMAGE==1
failover_process(bist, cpu_init_detectedx);
#else
real_main(bist, cpu_init_detectedx);
#endif
#else
- #if USE_FALLBACK_IMAGE == 1
+ #if CONFIG_USE_FALLBACK_IMAGE == 1
failover_process(bist, cpu_init_detectedx);
#endif
real_main(bist, cpu_init_detectedx);
#endif
}
-#if USE_FAILOVER_IMAGE==0
+#if CONFIG_USE_FAILOVER_IMAGE==0
void real_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
#endif
};
- struct sys_info *sysinfo = (DCACHE_RAM_BASE + DCACHE_RAM_SIZE - DCACHE_RAM_GLOBAL_VAR_SIZE);
+ struct sys_info *sysinfo = (CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE);
int needs_reset = 0;
unsigned bsp_apicid = 0;
pnp_enter_ext_func_mode(SERIAL_DEV);
pnp_write_config(SERIAL_DEV, 0x23, 0);
- it8716f_enable_dev(SERIAL_DEV, TTYS0_BASE);
+ it8716f_enable_dev(SERIAL_DEV, CONFIG_TTYS0_BASE);
pnp_exit_ext_func_mode(SERIAL_DEV);
setup_mb_resource_map();
print_debug("bsp_apicid="); print_debug_hex8(bsp_apicid); print_debug("\r\n");
-#if MEM_TRAIN_SEQ == 1
+#if CONFIG_MEM_TRAIN_SEQ == 1
set_sysinfo_in_ram(0); // in BSP so could hold all ap until sysinfo is in ram
#endif
setup_coherent_ht_domain(); // routing table and start other core0
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/failovercalculation.lb
arch i386 end
#needed by irq_tables and mptable and acpi_tables
object get_bus_conf.o
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
#object reset.o
if CONFIG_USE_INIT
makerule ./cache_as_ram_auto.o
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
end
else
makerule ./cache_as_ram_auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
end
-if USE_FAILOVER_IMAGE
+if CONFIG_USE_FAILOVER_IMAGE
else
if CONFIG_AP_CODE_IN_CAR
makerule ./apc_auto.o
- depends "$(MAINBOARD)/apc_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/apc_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/apc_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/apc_auto.c -o $@"
end
ldscript /arch/i386/init/ldscript_apc.lb
end
##
## Build our 16 bit and 32 bit coreboot entry code
##
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
end
##
## Build our reset vector (This is where coreboot is entered)
##
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
ldscript /cpu/x86/32bit/reset32.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
##
## ROMSTRAP table for MCP55
##
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
mainboardinit southbridge/nvidia/mcp55/romstrap.inc
ldscript /southbridge/nvidia/mcp55/romstrap.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
mainboardinit southbridge/nvidia/mcp55/romstrap.inc
ldscript /southbridge/nvidia/mcp55/romstrap.lds
end
### Things are delicate and we test to see if we should
### failover to another image.
###
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
ldscript /arch/i386/lib/failover_failover.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
end
end
-if HAVE_FANCTL
+if CONFIG_HAVE_FANCTL
object fanctl.o
end
##
## ACPI Support
##
-if HAVE_ACPI_TABLES
+if CONFIG_HAVE_ACPI_TABLES
object acpi_tables.o
makerule dsdt.c
- depends "$(MAINBOARD)/dsdt.asl"
- action "iasl -p $(PWD)/dsdt -tc $(MAINBOARD)/dsdt.asl"
+ depends "$(CONFIG_MAINBOARD)/dsdt.asl"
+ action "iasl -p $(PWD)/dsdt -tc $(CONFIG_MAINBOARD)/dsdt.asl"
action "mv dsdt.hex dsdt.c"
end
object ./dsdt.o
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses HAVE_ACPI_TABLES
-uses HAVE_ACPI_RESUME
-uses ACPI_SSDTX_NUM
-uses USE_FALLBACK_IMAGE
-uses USE_FAILOVER_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_FAILOVER_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_HAVE_ACPI_TABLES
+uses CONFIG_HAVE_ACPI_RESUME
+uses CONFIG_ACPI_SSDTX_NUM
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_USE_FAILOVER_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_FAILOVER_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_MAX_CPUS
uses CONFIG_MAX_PHYSICAL_CPUS
uses CONFIG_LOGICAL_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses FAILOVER_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_FAILOVER_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_NRV2B
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
-uses _RAMBASE
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_RAMBASE
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_SERIAL8250
-uses HAVE_INIT_TIMER
+uses CONFIG_HAVE_INIT_TIMER
uses CONFIG_GDB_STUB
uses CONFIG_GDB_STUB
-uses CROSS_COMPILE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
uses CONFIG_CONSOLE_VGA
uses CONFIG_USBDEBUG_DIRECT
uses CONFIG_PCI_ROM_RUN
-uses HW_MEM_HOLE_SIZEK
-uses HW_MEM_HOLE_SIZE_AUTO_INC
-uses K8_HT_FREQ_1G_SUPPORT
+uses CONFIG_HW_MEM_HOLE_SIZEK
+uses CONFIG_HW_MEM_HOLE_SIZE_AUTO_INC
+uses CONFIG_K8_HT_FREQ_1G_SUPPORT
-uses HAVE_HIGH_TABLES
+uses CONFIG_HAVE_HIGH_TABLES
-uses HT_CHAIN_UNITID_BASE
-uses HT_CHAIN_END_UNITID_BASE
-uses SB_HT_CHAIN_ON_BUS0
-uses SB_HT_CHAIN_UNITID_OFFSET_ONLY
+uses CONFIG_HT_CHAIN_UNITID_BASE
+uses CONFIG_HT_CHAIN_END_UNITID_BASE
+uses CONFIG_SB_HT_CHAIN_ON_BUS0
+uses CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
-uses DCACHE_RAM_GLOBAL_VAR_SIZE
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
+uses CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE
uses CONFIG_USE_INIT
-uses SERIAL_CPU_INIT
+uses CONFIG_SERIAL_CPU_INIT
-uses ENABLE_APIC_EXT_ID
-uses APIC_ID_OFFSET
-uses LIFT_BSP_APIC_ID
+uses CONFIG_ENABLE_APIC_EXT_ID
+uses CONFIG_APIC_ID_OFFSET
+uses CONFIG_LIFT_BSP_APIC_ID
uses CONFIG_PCI_64BIT_PREF_MEM
uses CONFIG_AP_CODE_IN_CAR
-uses MEM_TRAIN_SEQ
+uses CONFIG_MEM_TRAIN_SEQ
-uses WAIT_BEFORE_CPUS_INIT
+uses CONFIG_WAIT_BEFORE_CPUS_INIT
uses CONFIG_USE_PRINTK_IN_CAR
-uses HAVE_FANCTL
+uses CONFIG_HAVE_FANCTL
###
### Build options
###
##
-## ROM_SIZE is the size of boot ROM that this board will use.
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
##
-default ROM_SIZE=524288
-#default ROM_SIZE=0x100000
+default CONFIG_ROM_SIZE=524288
+#default CONFIG_ROM_SIZE=0x100000
##
-## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
+## CONFIG_FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
##
-#default FALLBACK_SIZE=131072
-#default FALLBACK_SIZE=0x40000
+#default CONFIG_FALLBACK_SIZE=131072
+#default CONFIG_FALLBACK_SIZE=0x40000
#FALLBACK: 256K-4K
-default FALLBACK_SIZE=0x3f000
+default CONFIG_FALLBACK_SIZE=0x3f000
#FAILOVER: 4K
-default FAILOVER_SIZE=0x01000
+default CONFIG_FAILOVER_SIZE=0x01000
#more 1M for pgtbl
default CONFIG_LB_MEM_TOPK=2048
##
## Set-up automatic fan control
##
-default HAVE_FANCTL=1
+default CONFIG_HAVE_FANCTL=1
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
-default HAVE_FAILOVER_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FAILOVER_BOOT=1
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=11
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=11
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
## HIGH tables support
-default HAVE_HIGH_TABLES=1
+default CONFIG_HAVE_HIGH_TABLES=1
## ACPI tables will be included
-default HAVE_ACPI_TABLES=1
+default CONFIG_HAVE_ACPI_TABLES=1
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
##
## Move the default coreboot cmos range off of AMD RTC registers
##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
+default CONFIG_LB_CKS_RANGE_START=49
+default CONFIG_LB_CKS_RANGE_END=122
+default CONFIG_LB_CKS_LOC=123
##
## Build code for SMP support
default CONFIG_MAX_PHYSICAL_CPUS=1
default CONFIG_LOGICAL_CPUS=1
-#default SERIAL_CPU_INIT=0
+#default CONFIG_SERIAL_CPU_INIT=0
-default ENABLE_APIC_EXT_ID=0
-default APIC_ID_OFFSET=0x10
-default LIFT_BSP_APIC_ID=1
+default CONFIG_ENABLE_APIC_EXT_ID=0
+default CONFIG_APIC_ID_OFFSET=0x10
+default CONFIG_LIFT_BSP_APIC_ID=1
#memory hole size, 0 mean disable, others will enable the hole, at that case if it is small than mmio_basek, it will use mmio_basek instead.
#2G
-#default HW_MEM_HOLE_SIZEK=0x200000
+#default CONFIG_HW_MEM_HOLE_SIZEK=0x200000
#1G
-default HW_MEM_HOLE_SIZEK=0x100000
+default CONFIG_HW_MEM_HOLE_SIZEK=0x100000
#512M
-#default HW_MEM_HOLE_SIZEK=0x80000
+#default CONFIG_HW_MEM_HOLE_SIZEK=0x80000
#make auto increase hole size to avoid hole_startk equal to basek so as to make some kernel happy
-#default HW_MEM_HOLE_SIZE_AUTO_INC=1
+#default CONFIG_HW_MEM_HOLE_SIZE_AUTO_INC=1
#Opteron K8 1G HT Support
-default K8_HT_FREQ_1G_SUPPORT=1
+default CONFIG_K8_HT_FREQ_1G_SUPPORT=1
#VGA Console
default CONFIG_CONSOLE_VGA=1
#default CONFIG_USBDEBUG_DIRECT=1
#HT Unit ID offset, default is 1, the typical one, 0 mean only one HT device
-default HT_CHAIN_UNITID_BASE=0
+default CONFIG_HT_CHAIN_UNITID_BASE=0
#real SB Unit ID, default is 0x20, mean dont touch it at last
-#default HT_CHAIN_END_UNITID_BASE=0x6
+#default CONFIG_HT_CHAIN_END_UNITID_BASE=0x6
#make the SB HT chain on bus 0, default is not (0)
-default SB_HT_CHAIN_ON_BUS0=2
+default CONFIG_SB_HT_CHAIN_ON_BUS0=2
#only offset for SB chain?, default is yes(1)
-default SB_HT_CHAIN_UNITID_OFFSET_ONLY=0
+default CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY=0
#allow capable device use that above 4G
#default CONFIG_PCI_64BIT_PREF_MEM=1
##
## enable CACHE_AS_RAM specifics
##
-default USE_DCACHE_RAM=1
-default DCACHE_RAM_BASE=0xc8000
-default DCACHE_RAM_SIZE=0x08000
-default DCACHE_RAM_GLOBAL_VAR_SIZE=0x01000
+default CONFIG_USE_DCACHE_RAM=1
+default CONFIG_DCACHE_RAM_BASE=0xc8000
+default CONFIG_DCACHE_RAM_SIZE=0x08000
+default CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE=0x01000
default CONFIG_USE_INIT=0
default CONFIG_AP_CODE_IN_CAR=0
-default MEM_TRAIN_SEQ=2
-default WAIT_BEFORE_CPUS_INIT=0
+default CONFIG_MEM_TRAIN_SEQ=2
+default CONFIG_WAIT_BEFORE_CPUS_INIT=0
##
## Build code to setup a generic IOAPIC
##
## Clean up the motherboard id strings
##
-default MAINBOARD_PART_NUMBER="m57sli"
-default MAINBOARD_VENDOR="GIGABYTE"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x1022
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2b80
+default CONFIG_MAINBOARD_PART_NUMBER="m57sli"
+default CONFIG_MAINBOARD_VENDOR="GIGABYTE"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x1022
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2b80
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 32K heap
##
-default HEAP_SIZE=0x8000
+default CONFIG_HEAP_SIZE=0x8000
##
## Only use the option table in a normal image
##
-default USE_OPTION_TABLE = (!USE_FALLBACK_IMAGE) && (!USE_FAILOVER_IMAGE )
+default CONFIG_USE_OPTION_TABLE = (!CONFIG_USE_FALLBACK_IMAGE) && (!CONFIG_USE_FAILOVER_IMAGE )
##
## Coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00100000
+default CONFIG_RAMBASE=0x00100000
##
## Load the payload from the ROM
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## Disable the gdb stub by default
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
#
# CBFS
void hardwaremain(int ret_addr)
{
- struct sys_info *sysinfo = (DCACHE_RAM_BASE + DCACHE_RAM_SIZE - DCACHE_RAM_GLOBAL_VAR_SIZE); // in CACHE
- struct sys_info *sysinfox = ((CONFIG_LB_MEM_TOPK<<10) - DCACHE_RAM_GLOBAL_VAR_SIZE); // in RAM
+ struct sys_info *sysinfo = (CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE); // in CACHE
+ struct sys_info *sysinfox = ((CONFIG_LB_MEM_TOPK<<10) - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE); // in RAM
struct node_core_id id;
//if we want to wait for core1 done before DQS training, set it to 0
#define K8_SET_FIDVID_CORE0_ONLY 1
-#if K8_REV_F_SUPPORT == 1
+#if CONFIG_K8_REV_F_SUPPORT == 1
#define K8_REV_F_SUPPORT_F0_F1_WORKAROUND 0
#endif
#include "option_table.h"
#include "pc80/mc146818rtc_early.c"
-#if USE_FAILOVER_IMAGE==0
+#if CONFIG_USE_FAILOVER_IMAGE==0
#include "pc80/serial.c"
#include "arch/i386/lib/console.c"
#if CONFIG_USBDEBUG_DIRECT
#include "superio/ite/it8716f/it8716f_early_serial.c"
#include "superio/ite/it8716f/it8716f_early_init.c"
-#if USE_FAILOVER_IMAGE==0
+#if CONFIG_USE_FAILOVER_IMAGE==0
#include "cpu/x86/bist.h"
#endif
-#if ((HAVE_FAILOVER_BOOT==1) && (USE_FAILOVER_IMAGE == 1)) || ((HAVE_FAILOVER_BOOT==0) && (USE_FALLBACK_IMAGE == 1))
+#if ((CONFIG_HAVE_FAILOVER_BOOT==1) && (CONFIG_USE_FAILOVER_IMAGE == 1)) || ((CONFIG_HAVE_FAILOVER_BOOT==0) && (CONFIG_USE_FALLBACK_IMAGE == 1))
#include "southbridge/nvidia/mcp55/mcp55_enable_rom.c"
#include "northbridge/amd/amdk8/early_ht.c"
);
fallback_image:
-#if HAVE_FAILOVER_BOOT==1
+#if CONFIG_HAVE_FAILOVER_BOOT==1
__asm__ volatile ("jmp __fallback_image"
: /* outputs */
: "a" (bist), "b" (cpu_init_detectedx) /* inputs */
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
-#if HAVE_FAILOVER_BOOT==1
- #if USE_FAILOVER_IMAGE==1
+#if CONFIG_HAVE_FAILOVER_BOOT==1
+ #if CONFIG_USE_FAILOVER_IMAGE==1
failover_process(bist, cpu_init_detectedx);
#else
real_main(bist, cpu_init_detectedx);
#endif
#else
- #if USE_FALLBACK_IMAGE == 1
+ #if CONFIG_USE_FALLBACK_IMAGE == 1
failover_process(bist, cpu_init_detectedx);
#endif
real_main(bist, cpu_init_detectedx);
#endif
}
-#if USE_FAILOVER_IMAGE==0
+#if CONFIG_USE_FAILOVER_IMAGE==0
void real_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
#endif
};
- struct sys_info *sysinfo = (DCACHE_RAM_BASE + DCACHE_RAM_SIZE - DCACHE_RAM_GLOBAL_VAR_SIZE);
+ struct sys_info *sysinfo = (CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE);
int needs_reset = 0;
unsigned bsp_apicid = 0;
pnp_write_config(GPIO_DEV, 0x64, 0x08);
pnp_write_config(GPIO_DEV, 0x65, 0x20);
/* We can get away with not resetting the logical device because
- * it8716f_enable_dev(SERIAL_DEV, TTYS0_BASE) will do that.
+ * it8716f_enable_dev(SERIAL_DEV, CONFIG_TTYS0_BASE) will do that.
*/
}
- it8716f_enable_dev(SERIAL_DEV, TTYS0_BASE);
+ it8716f_enable_dev(SERIAL_DEV, CONFIG_TTYS0_BASE);
pnp_exit_ext_func_mode(SERIAL_DEV);
setup_mb_resource_map();
print_debug("bsp_apicid="); print_debug_hex8(bsp_apicid); print_debug("\r\n");
-#if MEM_TRAIN_SEQ == 1
+#if CONFIG_MEM_TRAIN_SEQ == 1
set_sysinfo_in_ram(0); // in BSP so could hold all ap until sysinfo is in ram
#endif
setup_coherent_ht_domain(); // routing table and start other core0
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
arch i386 end
#needed by irq_tables and mptable and acpi_tables
object get_bus_conf.o
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
if CONFIG_USE_INIT
makerule ./auto.o
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
end
else
makerule ./auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
##
## Build our 16 bit and 32 bit coreboot entry code
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
end
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
end
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
-uses HAVE_PIRQ_TABLE
-uses HAVE_ACPI_TABLES
-uses ACPI_SSDTX_NUM
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_HAVE_ACPI_TABLES
+uses CONFIG_ACPI_SSDTX_NUM
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_MAX_CPUS
uses CONFIG_MAX_PHYSICAL_CPUS
uses CONFIG_LOGICAL_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
-uses _RAMBASE
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_RAMBASE
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_SERIAL8250
-uses HAVE_INIT_TIMER
+uses CONFIG_HAVE_INIT_TIMER
uses CONFIG_GDB_STUB
uses CONFIG_GDB_STUB
-uses CROSS_COMPILE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
-uses HW_MEM_HOLE_SIZEK
-uses HW_MEM_HOLE_SIZE_AUTO_INC
-uses K8_HT_FREQ_1G_SUPPORT
+uses CONFIG_HW_MEM_HOLE_SIZEK
+uses CONFIG_HW_MEM_HOLE_SIZE_AUTO_INC
+uses CONFIG_K8_HT_FREQ_1G_SUPPORT
uses CONFIG_CBFS
-uses HT_CHAIN_UNITID_BASE
-uses HT_CHAIN_END_UNITID_BASE
-uses SB_HT_CHAIN_ON_BUS0
-uses SB_HT_CHAIN_UNITID_OFFSET_ONLY
+uses CONFIG_HT_CHAIN_UNITID_BASE
+uses CONFIG_HT_CHAIN_END_UNITID_BASE
+uses CONFIG_SB_HT_CHAIN_ON_BUS0
+uses CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
-uses DCACHE_RAM_GLOBAL_VAR_SIZE
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
+uses CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE
uses CONFIG_USE_INIT
-uses SERIAL_CPU_INIT
+uses CONFIG_SERIAL_CPU_INIT
-uses ENABLE_APIC_EXT_ID
-uses APIC_ID_OFFSET
-uses LIFT_BSP_APIC_ID
+uses CONFIG_ENABLE_APIC_EXT_ID
+uses CONFIG_APIC_ID_OFFSET
+uses CONFIG_LIFT_BSP_APIC_ID
uses CONFIG_PCI_64BIT_PREF_MEM
###
##
-## ROM_SIZE is the size of boot ROM that this board will use.
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
##
-default ROM_SIZE=524288
+default CONFIG_ROM_SIZE=524288
##
-## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
+## CONFIG_FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
##
-default FALLBACK_SIZE=ROM_IMAGE_SIZE
+default CONFIG_FALLBACK_SIZE=CONFIG_ROM_IMAGE_SIZE
#more 1M for pgtbl
default CONFIG_LB_MEM_TOPK=2048
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## Build code to reset the motherboard from linuxBIOS
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=15
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=15
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
##
## Move the default coreboot cmos range off of AMD RTC registers
##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
+default CONFIG_LB_CKS_RANGE_START=49
+default CONFIG_LB_CKS_RANGE_END=122
+default CONFIG_LB_CKS_LOC=123
##
## Build code for SMP support
default CONFIG_MAX_PHYSICAL_CPUS=2
default CONFIG_LOGICAL_CPUS=1
-default SERIAL_CPU_INIT=0
+default CONFIG_SERIAL_CPU_INIT=0
-default ENABLE_APIC_EXT_ID=0
-default APIC_ID_OFFSET=0x8
-default LIFT_BSP_APIC_ID=1
+default CONFIG_ENABLE_APIC_EXT_ID=0
+default CONFIG_APIC_ID_OFFSET=0x8
+default CONFIG_LIFT_BSP_APIC_ID=1
#memory hole size, 0 mean disable, others will enable the hole, at that case if it is small than mmio_basek, it will use mmio_basek instead.
#2G
-#default HW_MEM_HOLE_SIZEK=0x200000
+#default CONFIG_HW_MEM_HOLE_SIZEK=0x200000
#1G
-default HW_MEM_HOLE_SIZEK=0x100000
+default CONFIG_HW_MEM_HOLE_SIZEK=0x100000
#512M
-#default HW_MEM_HOLE_SIZEK=0x80000
+#default CONFIG_HW_MEM_HOLE_SIZEK=0x80000
#make auto increase hole size to avoid hole_startk equal to basek so as to make some kernel happy
-#default HW_MEM_HOLE_SIZE_AUTO_INC=1
+#default CONFIG_HW_MEM_HOLE_SIZE_AUTO_INC=1
#Opteron K8 1G HT Support
-default K8_HT_FREQ_1G_SUPPORT=1
+default CONFIG_K8_HT_FREQ_1G_SUPPORT=1
#VGA Console
default CONFIG_CONSOLE_VGA=1
default CONFIG_PCI_ROM_RUN=0
#HT Unit ID offset, default is 1, the typical one
-default HT_CHAIN_UNITID_BASE=0x06
+default CONFIG_HT_CHAIN_UNITID_BASE=0x06
#real SB Unit ID, default is 0x20, mean dont touch it at last
-default HT_CHAIN_END_UNITID_BASE=0x01
+default CONFIG_HT_CHAIN_END_UNITID_BASE=0x01
#make the SB HT chain on bus 0, default is not (0)
-default SB_HT_CHAIN_ON_BUS0=2
+default CONFIG_SB_HT_CHAIN_ON_BUS0=2
#only offset for SB chain?, default is yes(1)
-#default SB_HT_CHAIN_UNITID_OFFSET_ONLY=0
+#default CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY=0
#allow capable device use that above 4G
#default CONFIG_PCI_64BIT_PREF_MEM=1
##
## enable CACHE_AS_RAM specifics
##
-default USE_DCACHE_RAM=1
-default DCACHE_RAM_BASE=0xcc000
-default DCACHE_RAM_SIZE=0x04000
-default DCACHE_RAM_GLOBAL_VAR_SIZE=0x01000
+default CONFIG_USE_DCACHE_RAM=1
+default CONFIG_DCACHE_RAM_BASE=0xcc000
+default CONFIG_DCACHE_RAM_SIZE=0x04000
+default CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE=0x01000
default CONFIG_USE_INIT=0
##
##
## Clean up the motherboard id strings
##
-default MAINBOARD_PART_NUMBER="DL145 G3"
-default MAINBOARD_VENDOR="HP"
-#default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x1022
-#default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2b80
+default CONFIG_MAINBOARD_PART_NUMBER="DL145 G3"
+default CONFIG_MAINBOARD_VENDOR="HP"
+#default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x1022
+#default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2b80
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 32K heap
##
-default HEAP_SIZE=0x8000
+default CONFIG_HEAP_SIZE=0x8000
##
## Only use the option table in a normal image
##
-default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
##
## Coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00100000
+default CONFIG_RAMBASE=0x00100000
##
## Load the payload from the ROM
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## Disable the gdb stub by default
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
##
## CBFS
//if we want to wait for core1 done before DQS training, set it to 0
#define K8_SET_FIDVID_CORE0_ONLY 1
-#if K8_REV_F_SUPPORT == 1
+#if CONFIG_K8_REV_F_SUPPORT == 1
#define K8_REV_F_SUPPORT_F0_F1_WORKAROUND 0
#endif
#include "pc80/mc146818rtc_early.c"
-#if USE_FAILOVER_IMAGE==0
+#if CONFIG_USE_FAILOVER_IMAGE==0
#include "pc80/serial.c"
#include "arch/i386/lib/console.c"
#include "ram/ramtest.c"
#include "superio/nsc/pc87417/pc87417_early_serial.c"
-#if USE_FAILOVER_IMAGE==0
+#if CONFIG_USE_FAILOVER_IMAGE==0
#include "cpu/x86/bist.h"
#endif
-#if ((HAVE_FAILOVER_BOOT==1) && (USE_FAILOVER_IMAGE == 1)) || ((HAVE_FAILOVER_BOOT==0) && (USE_FALLBACK_IMAGE == 1))
+#if ((CONFIG_HAVE_FAILOVER_BOOT==1) && (CONFIG_USE_FAILOVER_IMAGE == 1)) || ((CONFIG_HAVE_FAILOVER_BOOT==0) && (CONFIG_USE_FALLBACK_IMAGE == 1))
#include "northbridge/amd/amdk8/early_ht.c"
);
fallback_image:
-#if HAVE_FAILOVER_BOOT==1
+#if CONFIG_HAVE_FAILOVER_BOOT==1
__asm__ volatile ("jmp __fallback_image"
: /* outputs */
: "a" (bist), "b" (cpu_init_detectedx) /* inputs */
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
-#if HAVE_FAILOVER_BOOT==1
- #if USE_FAILOVER_IMAGE==1
+#if CONFIG_HAVE_FAILOVER_BOOT==1
+ #if CONFIG_USE_FAILOVER_IMAGE==1
failover_process(bist, cpu_init_detectedx);
#else
real_main(bist, cpu_init_detectedx);
#endif
#else
- #if USE_FALLBACK_IMAGE == 1
+ #if CONFIG_USE_FALLBACK_IMAGE == 1
failover_process(bist, cpu_init_detectedx);
#endif
real_main(bist, cpu_init_detectedx);
#endif
}
-#if USE_FAILOVER_IMAGE==0
+#if CONFIG_USE_FAILOVER_IMAGE==0
void real_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
};
- struct sys_info *sysinfo = (DCACHE_RAM_BASE + DCACHE_RAM_SIZE - DCACHE_RAM_GLOBAL_VAR_SIZE);
+ struct sys_info *sysinfo = (CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE);
int needs_reset;
unsigned bsp_apicid = 0;
bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);
}
- pilot_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ pilot_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
//setup_mp_resource_map();
print_debug("bsp_apicid="); print_debug_hex8(bsp_apicid); print_debug("\r\n");
-#if MEM_TRAIN_SEQ == 1
+#if CONFIG_MEM_TRAIN_SEQ == 1
set_sysinfo_in_ram(0); // in BSP so could hold all ap until sysinfo is in ram
#endif
setup_coherent_ht_domain();
printk_debug("now found %s...\n",dev_path(dev));
if(dev) {
m->bus_bcm5785_1_1 = pci_read_config8(dev, PCI_SECONDARY_BUS);
-#if HT_CHAIN_END_UNITID_BASE >= HT_CHAIN_UNITID_BASE
+#if CONFIG_HT_CHAIN_END_UNITID_BASE >= CONFIG_HT_CHAIN_UNITID_BASE
m->bus_isa = pci_read_config8(dev, PCI_SUBORDINATE_BUS);
m->bus_isa++;
printk_debug("bus_isa 1=%d\n",m->bus_isa);
dev = dev_find_slot(m->bus_bcm5780[0], PCI_DEVFN(m->sbdn2 + i - 1,0));
if(dev) {
m->bus_bcm5780[i] = pci_read_config8(dev, PCI_SECONDARY_BUS);
-#if HT_CHAIN_END_UNITID_BASE < HT_CHAIN_UNITID_BASE
+#if CONFIG_HT_CHAIN_END_UNITID_BASE < CONFIG_HT_CHAIN_UNITID_BASE
m->bus_isa = pci_read_config8(dev, PCI_SUBORDINATE_BUS);
m->bus_isa++;
printk_debug("bus_isa 2=%d\n",m->bus_isa);
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
##
##
driver mainboard.o
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
#object reset.o
if CONFIG_USE_INIT
makerule ./auto.o
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
end
else
makerule ./auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
##
## Build our 16 bit and 32 bit coreboot entry code
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
end
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
end
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_MAX_CPUS
uses CONFIG_MAX_PHYSICAL_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD
uses COREBOOT_EXTRA_VERSION
-uses _RAMBASE
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_RAMBASE
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_SERIAL8250
-uses CROSS_COMPILE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
uses CONFIG_USE_INIT
uses CONFIG_USE_PRINTK_IN_CAR
###
##
-## ROM_SIZE is the size of boot ROM that this board will use.
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
##
-default ROM_SIZE=524288
+default CONFIG_ROM_SIZE=524288
##
-## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
+## CONFIG_FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
##
-default FALLBACK_SIZE=0x40000
+default CONFIG_FALLBACK_SIZE=0x40000
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=9
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=9
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
##
## Move the default coreboot cmos range off of AMD RTC registers
##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
+default CONFIG_LB_CKS_RANGE_START=49
+default CONFIG_LB_CKS_RANGE_END=122
+default CONFIG_LB_CKS_LOC=123
##
## Build code for SMP support
##
## enable CACHE_AS_RAM specifics
##
-default USE_DCACHE_RAM=1
-default DCACHE_RAM_BASE=0xcf000
-default DCACHE_RAM_SIZE=0x1000
+default CONFIG_USE_DCACHE_RAM=1
+default CONFIG_DCACHE_RAM_BASE=0xcf000
+default CONFIG_DCACHE_RAM_SIZE=0x1000
default CONFIG_USE_INIT=0
##
## Clean up the motherboard id strings
##
-default MAINBOARD_PART_NUMBER="E325"
-default MAINBOARD_VENDOR="IBM"
-#default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x161f
-#default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x3016
+default CONFIG_MAINBOARD_PART_NUMBER="E325"
+default CONFIG_MAINBOARD_VENDOR="IBM"
+#default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x161f
+#default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x3016
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE=0x8000
+default CONFIG_HEAP_SIZE=0x8000
##
## Only use the option table in a normal image
##
-default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
##
## Coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00004000
+default CONFIG_RAMBASE=0x00004000
##
## Load the payload from the ROM
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
default CONFIG_USE_PRINTK_IN_CAR=1
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
### End Options.lb
#
#include "cpu/amd/model_fxx/init_cpus.c"
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
#include "southbridge/amd/amd8111/amd8111_enable_rom.c"
#include "northbridge/amd/amdk8/early_ht.c"
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
failover_process(bist, cpu_init_detectedx);
#endif
real_main(bist, cpu_init_detectedx);
init_cpus(cpu_init_detectedx);
}
- pc87366_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ pc87366_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
#include <arch/pirq_routing.h>
#include <device/pci.h>
-#define IRQ_SLOT_COUNT 12
+#define CONFIG_IRQ_SLOT_COUNT 12
#define IRQ_ROUTER_BUS 0
#define IRQ_ROUTER_DEVFN PCI_DEVFN(4,3)
#define IRQ_ROUTER_VENDOR 0x1022
const struct irq_routing_table intel_irq_routing_table = {
PIRQ_SIGNATURE, /* u32 signature */
PIRQ_VERSION, /* u16 version */
- 32+16*IRQ_SLOT_COUNT, /* there can be total IRQ_SLOT_COUNT table entries */
+ 32+16*CONFIG_IRQ_SLOT_COUNT, /* there can be total CONFIG_IRQ_SLOT_COUNT table entries */
IRQ_ROUTER_BUS, /* Where the interrupt router lies (bus) */
IRQ_ROUTER_DEVFN, /* Where the interrupt router lies (dev) */
0x00, /* IRQs devoted exclusively to PCI usage */
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
##
##
driver mainboard.o
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
#object reset.o
if CONFIG_USE_INIT
makerule ./auto.o
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
end
else
makerule ./auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
##
## Build our 16 bit and 32 bit coreboot entry code
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
end
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
end
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_MAX_CPUS
uses CONFIG_MAX_PHYSICAL_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD
uses COREBOOT_EXTRA_VERSION
-uses _RAMBASE
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_RAMBASE
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_SERIAL8250
-uses CROSS_COMPILE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
uses CONFIG_USE_INIT
uses CONFIG_USE_PRINTK_IN_CAR
###
##
-## ROM_SIZE is the size of boot ROM that this board will use.
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
##
-default ROM_SIZE=524288
+default CONFIG_ROM_SIZE=524288
##
-## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
+## CONFIG_FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
##
-default FALLBACK_SIZE=0x40000
+default CONFIG_FALLBACK_SIZE=0x40000
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=9
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=9
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
##
## Move the default coreboot cmos range off of AMD RTC registers
##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
+default CONFIG_LB_CKS_RANGE_START=49
+default CONFIG_LB_CKS_RANGE_END=122
+default CONFIG_LB_CKS_LOC=123
##
## Build code for SMP support
##
## enable CACHE_AS_RAM specifics
##
-default USE_DCACHE_RAM=1
-default DCACHE_RAM_BASE=0xcf000
-default DCACHE_RAM_SIZE=0x1000
+default CONFIG_USE_DCACHE_RAM=1
+default CONFIG_DCACHE_RAM_BASE=0xcf000
+default CONFIG_DCACHE_RAM_SIZE=0x1000
default CONFIG_USE_INIT=0
##
## Clean up the motherboard id strings
##
-default MAINBOARD_PART_NUMBER="E326"
-default MAINBOARD_VENDOR="IBM"
-#default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x161f
-#default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x3016
+default CONFIG_MAINBOARD_PART_NUMBER="E326"
+default CONFIG_MAINBOARD_VENDOR="IBM"
+#default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x161f
+#default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x3016
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE=0x8000
+default CONFIG_HEAP_SIZE=0x8000
##
## Only use the option table in a normal image
##
-default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
##
## Coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00004000
+default CONFIG_RAMBASE=0x00004000
##
## Load the payload from the ROM
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
default CONFIG_USE_PRINTK_IN_CAR=1
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
### End Options.lb
#
#include "cpu/amd/model_fxx/init_cpus.c"
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
#include "southbridge/amd/amd8111/amd8111_enable_rom.c"
#include "northbridge/amd/amdk8/early_ht.c"
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
failover_process(bist, cpu_init_detectedx);
#endif
real_main(bist, cpu_init_detectedx);
init_cpus(cpu_init_detectedx);
}
- pc87366_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ pc87366_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
#include <arch/pirq_routing.h>
#include <device/pci.h>
-#define IRQ_SLOT_COUNT 12
+#define CONFIG_IRQ_SLOT_COUNT 12
#define IRQ_ROUTER_BUS 0
#define IRQ_ROUTER_DEVFN PCI_DEVFN(4,3)
#define IRQ_ROUTER_VENDOR 0x1022
const struct irq_routing_table intel_irq_routing_table = {
PIRQ_SIGNATURE, /* u32 signature */
PIRQ_VERSION, /* u16 version */
- 32+16*IRQ_SLOT_COUNT, /* there can be total IRQ_SLOT_COUNT table entries */
+ 32+16*CONFIG_IRQ_SLOT_COUNT, /* there can be total CONFIG_IRQ_SLOT_COUNT table entries */
IRQ_ROUTER_BUS, /* Where the interrupt router lies (bus) */
IRQ_ROUTER_DEVFN, /* Where the interrupt router lies (dev) */
0x00, /* IRQs devoted exclusively to PCI usage */
## Compute the location and size of where this firmware image
## (coreboot plus bootloader) will live in the boot rom chip.
##
-default ROM_SIZE = 256 * 1024
-default ROM_SECTION_SIZE = ROM_SIZE
-default ROM_SECTION_OFFSET = 0
+default CONFIG_ROM_SIZE = 256 * 1024
+default CONFIG_ROM_SECTION_SIZE = CONFIG_ROM_SIZE
+default CONFIG_ROM_SECTION_OFFSET = 0
##
## Compute the start location and size size of
## The coreboot bootloader.
##
-default PAYLOAD_SIZE = ( ROM_SECTION_SIZE - ROM_IMAGE_SIZE )
-default CONFIG_ROM_PAYLOAD_START = (0xffffffff - ROM_SIZE + ROM_SECTION_OFFSET + 1)
+default CONFIG_PAYLOAD_SIZE = ( CONFIG_ROM_SECTION_SIZE - CONFIG_ROM_IMAGE_SIZE )
+default CONFIG_ROM_PAYLOAD_START = (0xffffffff - CONFIG_ROM_SIZE + CONFIG_ROM_SECTION_OFFSET + 1)
##
## Compute where this copy of coreboot will start in the boot rom
##
-default _ROMBASE = ( CONFIG_ROM_PAYLOAD_START + PAYLOAD_SIZE )
+default CONFIG_ROMBASE = ( CONFIG_ROM_PAYLOAD_START + CONFIG_PAYLOAD_SIZE )
##
## Compute a range of ROM that can cached to speed up coreboot,
## execution speed.
##
-## XIP_ROM_SIZE must be a power of 2.
-## XIP_ROM_BASE must be a multiple of XIP_ROM_SIZE
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+## CONFIG_XIP_ROM_BASE must be a multiple of CONFIG_XIP_ROM_SIZE
##
-default XIP_ROM_SIZE=65536
-default XIP_ROM_BASE = ( _ROMBASE + ROM_IMAGE_SIZE - XIP_ROM_SIZE )
+default CONFIG_XIP_ROM_SIZE=65536
+default CONFIG_XIP_ROM_BASE = ( CONFIG_ROMBASE + CONFIG_ROM_IMAGE_SIZE - CONFIG_XIP_ROM_SIZE )
##
## Set all of the defaults for an x86 architecture
driver mainboard.o
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
#object reset.o
##
## Romcc output
##
makerule ./failover.E
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./auto.E
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -E -mcpu=i386 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -E -mcpu=i386 -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -mcpu=i386 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -mcpu=i386 -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
uses CONFIG_UDELAY_IO
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_COMPRESS
uses CONFIG_COMPRESSED_PAYLOAD_NRV2B
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
uses CONFIG_ROM_PAYLOAD
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses HAVE_MP_TABLE
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
uses CONFIG_CONSOLE_SERIAL8250
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
uses CONFIG_VIDEO_MB
-uses PIRQ_ROUTE
+uses CONFIG_PIRQ_ROUTE
-## ROM_SIZE is the size of boot ROM that this board will use.
-default ROM_SIZE = 256*1024
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
+default CONFIG_ROM_SIZE = 256*1024
###
### Build options
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## no MP table
##
-default HAVE_MP_TABLE=0
+default CONFIG_HAVE_MP_TABLE=0
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=0
+default CONFIG_HAVE_HARD_RESET=0
default CONFIG_UDELAY_IO=1
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=0
-default IRQ_SLOT_COUNT=2
-default PIRQ_ROUTE=1
+default CONFIG_HAVE_PIRQ_TABLE=0
+default CONFIG_IRQ_SLOT_COUNT=2
+default CONFIG_PIRQ_ROUTE=1
#object irq_tables.o
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=0
+default CONFIG_HAVE_OPTION_TABLE=0
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
-default FALLBACK_SIZE = 131072
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
+default CONFIG_FALLBACK_SIZE = 131072
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE=0x4000
+default CONFIG_HEAP_SIZE=0x4000
##
## Only use the option table in a normal image
##
-#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
+#default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
# To Enable the Serial Console
default CONFIG_CONSOLE_SERIAL8250=1
-default DEFAULT_CONSOLE_LOGLEVEL=8
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
## The default compiler
##
-default CROSS_COMPILE=""
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CONFIG_CROSS_COMPILE=""
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
default CONFIG_VIDEO_MB = 0
static void main(unsigned long bist)
{
/* Initialize the serial console. */
- w83977f_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ w83977f_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
##
driver mainboard.o
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
#object reset.o
##
## Romcc output
##
makerule ./failover.E
- depends "$(MAINBOARD)/failover.c ../romcc"
- action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/failover.c ../romcc"
+ action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/failover.c ../romcc"
- action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/failover.c ../romcc"
+ action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/failover.c -o $@"
end
makerule ./auto.E
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -E -mcpu=i386 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -E -mcpu=i386 -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -mcpu=i386 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -mcpu=i386 -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
##
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_ROM_PAYLOAD
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses HAVE_MP_TABLE
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
uses CONFIG_CONSOLE_VGA
uses CONFIG_COMPRESSED_PAYLOAD_NRV2B
uses CONFIG_PRECOMPRESSED_PAYLOAD
uses CONFIG_VIDEO_MB
-uses PIRQ_ROUTE
+uses CONFIG_PIRQ_ROUTE
-## ROM_SIZE is the size of boot ROM that this board will use.
-default ROM_SIZE = 256*1024
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
+default CONFIG_ROM_SIZE = 256*1024
###
### Build options
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=0
+default CONFIG_HAVE_FALLBACK_BOOT=0
##
## no MP table
##
-default HAVE_MP_TABLE=0
+default CONFIG_HAVE_MP_TABLE=0
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=0
+default CONFIG_HAVE_HARD_RESET=0
## Delay timer options
##
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=7
-default PIRQ_ROUTE=1
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=7
+default CONFIG_PIRQ_ROUTE=1
#object irq_tables.o
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
-default FALLBACK_SIZE = 131072
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
+default CONFIG_FALLBACK_SIZE = 131072
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE=0x4000
+default CONFIG_HEAP_SIZE=0x4000
##
## Only use the option table in a normal image
##
-#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
+#default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
##
## The default compiler
##
-default CROSS_COMPILE=""
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CONFIG_CROSS_COMPILE=""
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## The Serial Console
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
default CONFIG_VIDEO_MB = 0
static void main(unsigned long bist)
{
/* Initialize the serial console. */
- w83977tf_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ w83977tf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
const struct irq_routing_table intel_irq_routing_table = {
.signature = PIRQ_SIGNATURE, /* u32 signature */
.version = PIRQ_VERSION, /* u16 version */
- .size = 32+16*IRQ_SLOT_COUNT, /* There can be total 4 devices on the bus */
+ .size = 32+16*CONFIG_IRQ_SLOT_COUNT, /* There can be total 4 devices on the bus */
.rtr_bus = 0x00, /* Where the interrupt router lies (bus) */
.rtr_devfn = (0x12<<3)|0x0, /* Where the interrupt router lies (dev) */
.exclusive_irqs = 0x4C20, /* IRQs devoted exclusively to PCI usage */
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
arch i386 end
driver mainboard.o
-if HAVE_PIRQ_TABLE
+if CONFIG_HAVE_PIRQ_TABLE
object irq_tables.o
end
# Compile cache_as_ram.c to auto.inc.
makerule ./cache_as_ram_auto.inc
- # depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- depends "$(MAINBOARD)/cache_as_ram_auto.c"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
mainboardinit cpu/x86/32bit/entry32.inc
ldscript /cpu/x86/16bit/entry16.lds
ldscript /cpu/x86/32bit/entry32.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
end
mainboardinit arch/i386/lib/id.inc
ldscript /arch/i386/lib/id.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
# mainboardinit ./failover.inc
end
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_ROM_PAYLOAD
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESS
uses CONFIG_COMPRESSED_PAYLOAD_NRV2B
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses HAVE_MP_TABLE
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
uses CONFIG_UDELAY_IO
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
uses CONFIG_VIDEO_MB
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
uses CONFIG_USE_PRINTK_IN_CAR
-uses PIRQ_ROUTE
+uses CONFIG_PIRQ_ROUTE
-default ROM_SIZE = 256 * 1024
+default CONFIG_ROM_SIZE = 256 * 1024
default CONFIG_CONSOLE_VGA = 0
default CONFIG_VIDEO_MB = 8
default CONFIG_PCI_ROM_RUN = 0
-default HAVE_FALLBACK_BOOT = 1
-default HAVE_MP_TABLE = 0
-default HAVE_HARD_RESET = 0
+default CONFIG_HAVE_FALLBACK_BOOT = 1
+default CONFIG_HAVE_MP_TABLE = 0
+default CONFIG_HAVE_HARD_RESET = 0
default CONFIG_UDELAY_IO = 1
-default HAVE_PIRQ_TABLE = 1
-default IRQ_SLOT_COUNT = 9
-default PIRQ_ROUTE = 1
-default HAVE_OPTION_TABLE = 0
-default ROM_IMAGE_SIZE = 64 * 1024
-default FALLBACK_SIZE = 128 * 1024
-default USE_DCACHE_RAM = 1
-default DCACHE_RAM_BASE = 0xc8000
-default DCACHE_RAM_SIZE = 32 * 1024
+default CONFIG_HAVE_PIRQ_TABLE = 1
+default CONFIG_IRQ_SLOT_COUNT = 9
+default CONFIG_PIRQ_ROUTE = 1
+default CONFIG_HAVE_OPTION_TABLE = 0
+default CONFIG_ROM_IMAGE_SIZE = 64 * 1024
+default CONFIG_FALLBACK_SIZE = 128 * 1024
+default CONFIG_USE_DCACHE_RAM = 1
+default CONFIG_DCACHE_RAM_BASE = 0xc8000
+default CONFIG_DCACHE_RAM_SIZE = 32 * 1024
default CONFIG_USE_PRINTK_IN_CAR=1
-default STACK_SIZE = 8 * 1024
-default HEAP_SIZE = 16 * 1024
-# default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_STACK_SIZE = 8 * 1024
+default CONFIG_HEAP_SIZE = 16 * 1024
+# default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 0
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
-default CROSS_COMPILE = ""
-default CC = "$(CROSS_COMPILE)gcc -m32"
-default HOSTCC = "gcc"
+default CONFIG_CROSS_COMPILE = ""
+default CC = "$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC = "gcc"
default CONFIG_CONSOLE_SERIAL8250 = 1
-default TTYS0_BAUD = 115200
-default TTYS0_BASE = 0x3f8
-default TTYS0_LCS = 0x3
-default DEFAULT_CONSOLE_LOGLEVEL=8
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_TTYS0_BAUD = 115200
+default CONFIG_TTYS0_BASE = 0x3f8
+default CONFIG_TTYS0_LCS = 0x3
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
#
/* Note: must do this AFTER the early_setup! It is counting on some
* early MSR setup for CS5536.
*/
- w83627hf_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ w83627hf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
mb_gpio_init();
uart_init();
console_init();
const struct irq_routing_table intel_irq_routing_table = {
PIRQ_SIGNATURE, /* u32 signature */
PIRQ_VERSION, /* u16 version */
- 32 + 16 * IRQ_SLOT_COUNT,/* there can be total 6 devices on the bus */
+ 32 + 16 * CONFIG_IRQ_SLOT_COUNT,/* there can be total 6 devices on the bus */
0x00, /* Where the interrupt router lies (bus) */
(0x0F << 3) | 0x0, /* Where the interrupt router lies (dev) */
EXCLUSIVE_PCI_IRQS, /* IRQs devoted exclusively to PCI usage */
##
## Only use the option table in a normal image
##
-default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 128 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 128 * 1024
include /config/nofailovercalculation.lb
##
##
driver mainboard.o
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
object reset.o
##
## Romcc output
##
makerule ./failover.E
- depends "$(MAINBOARD)/failover.c ../romcc"
- action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/failover.c ../romcc"
+ action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/failover.c ../romcc"
- action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/failover.c ../romcc"
+ action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/failover.c -o $@"
end
makerule ./auto.E
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -E -mcpu=p4 -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -E -mcpu=p4 -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -mcpu=p4 -fno-simplify-phi -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -mcpu=p4 -fno-simplify-phi -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
##
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_LOGICAL_CPUS
uses CONFIG_MAX_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
-uses _RAMBASE
+uses CONFIG_RAMBASE
uses CONFIG_GDB_STUB
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_BTEXT
uses CC
-uses HOSTCC
-uses CROSS_COMPILE
-uses OBJCOPY
-uses MAX_REBOOT_CNT
-uses USE_WATCHDOG_ON_BOOT
+uses CONFIG_HOSTCC
+uses CONFIG_CROSS_COMPILE
+uses CONFIG_OBJCOPY
+uses CONFIG_MAX_REBOOT_CNT
+uses CONFIG_USE_WATCHDOG_ON_BOOT
###
##
## Because we do the stutter start we need more attempts
##
-default MAX_REBOOT_CNT=8
+default CONFIG_MAX_REBOOT_CNT=8
##
## Use the watchdog to break out of a lockup condition
##
-default USE_WATCHDOG_ON_BOOT=1
+default CONFIG_USE_WATCHDOG_ON_BOOT=1
##
-## ROM_SIZE is the size of boot ROM that this board will use.
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
##
-default ROM_SIZE=2097152
+default CONFIG_ROM_SIZE=2097152
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## Delay timer options
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=9
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=9
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
##
## Move the default coreboot cmos range off of AMD RTC registers
##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
+default CONFIG_LB_CKS_RANGE_START=49
+default CONFIG_LB_CKS_RANGE_END=122
+default CONFIG_LB_CKS_LOC=123
##
## Build code for SMP support
##
## Clean up the motherboard id strings
##
-default MAINBOARD_PART_NUMBER="SE7520JR22D"
-default MAINBOARD_VENDOR= "Intel"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x8086
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x1079
-#default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x3437
+default CONFIG_MAINBOARD_PART_NUMBER="SE7520JR22D"
+default CONFIG_MAINBOARD_VENDOR= "Intel"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x8086
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x1079
+#default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x3437
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 32K heap
##
-default HEAP_SIZE=0x8000
+default CONFIG_HEAP_SIZE=0x8000
###
### Compute the location and size of where this firmware image
### (coreboot plus bootloader) will live in the boot rom chip.
###
-default FALLBACK_SIZE=131072
+default CONFIG_FALLBACK_SIZE=131072
##
## Coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00004000
+default CONFIG_RAMBASE=0x00004000
##
## Load the payload from the ROM
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## Disable the gdb stub by default
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
##
## Don't enable the btext console
/* Setup the console */
pc87427_disable_dev(CONSOLE_SERIAL_DEV);
pc87427_disable_dev(HIDDEN_SERIAL_DEV);
- pc87427_enable_dev(CONSOLE_SERIAL_DEV, TTYS0_BASE);
+ pc87427_enable_dev(CONSOLE_SERIAL_DEV, CONFIG_TTYS0_BASE);
/* Enable Serial 2 lines instead of GPIO */
outb(0x2c, 0x2e);
outb((inb(0x2f) & (~1<<1)), 0x2f);
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 128 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 128 * 1024
include /config/nofailovercalculation.lb
##
##
driver mainboard.o
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
##
## Romcc output
##
makerule ./failover.E
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./auto.E
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -E -mcpu=p4 -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -E -mcpu=p4 -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -mcpu=p4 -fno-simplify-phi -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -mcpu=p4 -fno-simplify-phi -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
##
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
uses CONFIG_LOGICAL_CPUS
uses CONFIG_MAX_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
-uses _RAMBASE
+uses CONFIG_RAMBASE
uses CONFIG_GDB_STUB
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CC
-uses HOSTCC
-uses CROSS_COMPILE
-uses OBJCOPY
+uses CONFIG_HOSTCC
+uses CONFIG_CROSS_COMPILE
+uses CONFIG_OBJCOPY
###
###
##
-## ROM_SIZE is the size of boot ROM that this board will use.
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
##
-default ROM_SIZE = 2 * 1024 * 1024
+default CONFIG_ROM_SIZE = 2 * 1024 * 1024
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## Delay timer options
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=1
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=1
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
##
## Build code for SMP support
##
## Clean up the motherboard id strings
##
-default MAINBOARD_PART_NUMBER="Mt. Arvon"
-default MAINBOARD_VENDOR= "Intel"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x8086
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2680
+default CONFIG_MAINBOARD_PART_NUMBER="Mt. Arvon"
+default CONFIG_MAINBOARD_VENDOR= "Intel"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x8086
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2680
###
### Coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 32K heap
##
-default HEAP_SIZE=0x8000
+default CONFIG_HEAP_SIZE=0x8000
###
### Compute the location and size of where this firmware image
### (coreboot plus bootloader) will live in the boot rom chip.
###
-default FALLBACK_SIZE=131072
+default CONFIG_FALLBACK_SIZE=131072
##
## coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00004000
+default CONFIG_RAMBASE=0x00004000
##
## Load the payload from the ROM
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## Disable the gdb stub by default
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=5
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=5
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=5
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=5
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
### End Options.lb
#
}
/* Set up the console */
i3100_enable_superio();
- i3100_enable_serial(0x4e, I3100_SP1, TTYS0_BASE);
+ i3100_enable_serial(0x4e, I3100_SP1, CONFIG_TTYS0_BASE);
uart_init();
console_init();
const struct irq_routing_table intel_irq_routing_table = {
PIRQ_SIGNATURE, /* u32 signature */
PIRQ_VERSION, /* u16 version */
- 32+16*IRQ_SLOT_COUNT, /* u16 Table size 32+(16*devices) */
+ 32+16*CONFIG_IRQ_SLOT_COUNT, /* u16 Table size 32+(16*devices) */
0x00, /* u8 Bus 0 */
(0x1f << 3) | 0x0, /* u8 Device 1f, Function 0 */
0x0000, /* u16 reserve IRQ for PCI */
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 128 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 128 * 1024
include /config/nofailovercalculation.lb
##
##
driver mainboard.o
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
##
## Romcc output
##
makerule ./failover.E
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./auto.E
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -E -mcpu=p4 -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -E -mcpu=p4 -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -mcpu=p4 -fno-simplify-phi -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -mcpu=p4 -fno-simplify-phi -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
##
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
uses CONFIG_LOGICAL_CPUS
uses CONFIG_MAX_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
-uses _RAMBASE
+uses CONFIG_RAMBASE
uses CONFIG_GDB_STUB
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CC
-uses HOSTCC
-uses CROSS_COMPILE
-uses OBJCOPY
+uses CONFIG_HOSTCC
+uses CONFIG_CROSS_COMPILE
+uses CONFIG_OBJCOPY
###
###
##
-## ROM_SIZE is the size of boot ROM that this board will use.
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
##
-default ROM_SIZE = 2 * 1024 * 1024
+default CONFIG_ROM_SIZE = 2 * 1024 * 1024
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## Delay timer options
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=1
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=1
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
##
## Build code for SMP support
##
## Clean up the motherboard id strings
##
-default MAINBOARD_PART_NUMBER="Truxton"
-default MAINBOARD_VENDOR= "Intel"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x8086
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2680
+default CONFIG_MAINBOARD_PART_NUMBER="Truxton"
+default CONFIG_MAINBOARD_VENDOR= "Intel"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x8086
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2680
###
### Coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 32K heap
##
-default HEAP_SIZE=0x8000
+default CONFIG_HEAP_SIZE=0x8000
###
### Compute the location and size of where this firmware image
### (coreboot plus bootloader) will live in the boot rom chip.
###
-default FALLBACK_SIZE=131072
+default CONFIG_FALLBACK_SIZE=131072
##
## coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00004000
+default CONFIG_RAMBASE=0x00004000
##
## Load the payload from the ROM
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## Disable the gdb stub by default
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=5
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=5
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=5
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=5
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
### End Options.lb
/* Set up the console */
i3100_enable_superio();
- i3100_enable_serial(I3100_SUPERIO_CONFIG_PORT, I3100_SP1, TTYS0_BASE);
+ i3100_enable_serial(I3100_SUPERIO_CONFIG_PORT, I3100_SP1, CONFIG_TTYS0_BASE);
uart_init();
console_init();
const struct irq_routing_table intel_irq_routing_table = {
PIRQ_SIGNATURE, /* u32 signature */
PIRQ_VERSION, /* u16 version */
- 32+16*IRQ_SLOT_COUNT, /* u16 Table size 32+(16*devices) */
+ 32+16*CONFIG_IRQ_SLOT_COUNT, /* u16 Table size 32+(16*devices) */
0x00, /* u8 Bus 0 */
(0x1f << 3) | 0x0, /* u8 Device 1f, Function 0 */
0x0000, /* u16 reserve IRQ for PCI */
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 128 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 128 * 1024
include /config/nofailovercalculation.lb
arch i386 end
##
driver mainboard.o
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE object irq_tables.o end
-if HAVE_ACPI_TABLES object acpi_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_ACPI_TABLES object acpi_tables.o end
object reset.o
# Include the VGA option ROM, but only if we're compiled to use it
## Romcc output
##
makerule ./failover.E
- depends "$(MAINBOARD)/failover.c ../romcc"
- action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/failover.c ../romcc"
+ action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/failover.c ../romcc"
- action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/failover.c ../romcc"
+ action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/failover.c -o $@"
end
makerule ./auto.E
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -E -mcpu=p4 -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -E -mcpu=p4 -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -mcpu=p4 -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -mcpu=p4 -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
##
##
## Build our reset vector (This is where coreboot is entered)
##
-if HAVE_FALLBACK_BOOT
- if USE_FALLBACK_IMAGE
+if CONFIG_HAVE_FALLBACK_BOOT
+ if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_ACPI_TABLES
-uses HAVE_ACPI_RESUME
-uses HAVE_PIRQ_TABLE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_OPTION_TABLE
-uses IRQ_SLOT_COUNT
+uses CONFIG_HAVE_ACPI_TABLES
+uses CONFIG_HAVE_ACPI_RESUME
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_IRQ_SLOT_COUNT
uses CONFIG_MAX_CPUS
uses CONFIG_LOGICAL_CPUS
uses CONFIG_MAX_PHYSICAL_CPUS
uses CONFIG_ROM_PAYLOAD
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
-uses _RAMBASE
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_RAMBASE
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_SERIAL8250
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
-uses HAVE_INIT_TIMER
+uses CONFIG_HAVE_INIT_TIMER
uses CONFIG_GDB_STUB
-uses CROSS_COMPILE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
-uses DEBUG
-#uses CPU_OPT
+uses CONFIG_DEBUG
+#uses CONFIG_CPU_OPT
uses CONFIG_IDE
## The default definitions are used for these
uses CONFIG_ROM_PAYLOAD_START
-uses PAYLOAD_SIZE
+uses CONFIG_PAYLOAD_SIZE
## These are defined in target Config.lb, don't add here
-uses USE_FALLBACK_IMAGE
-uses ROM_SIZE
-uses ROM_IMAGE_SIZE
-uses FALLBACK_SIZE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_FALLBACK_SIZE
uses COREBOOT_EXTRA_VERSION
## These are defined in mainboard Config.lb, don't add here
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
###
### Build options
###
##
-## ROM_SIZE is the size of boot ROM that this board will use.
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
##
-default ROM_SIZE=2097152
-default ROM_IMAGE_SIZE = 65536
+default CONFIG_ROM_SIZE=2097152
+default CONFIG_ROM_IMAGE_SIZE = 65536
##
## Build code for the fallback boot?
##
-default HAVE_FALLBACK_BOOT=1
-default FALLBACK_SIZE=131072
+default CONFIG_HAVE_FALLBACK_BOOT=1
+default CONFIG_FALLBACK_SIZE=131072
## Delay timer options
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=12
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=12
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
## Build code to export ACPI tables?
-default HAVE_ACPI_TABLES=1
+default CONFIG_HAVE_ACPI_TABLES=1
##
## Build code to export a CMOS option table?
##
-default HAVE_OPTION_TABLE=0
+default CONFIG_HAVE_OPTION_TABLE=0
## CMOS checksum definitions (units == bytes)
## These must match the checksum record in cmos.layout
-default LB_CKS_RANGE_START=128
-default LB_CKS_RANGE_END=130
-default LB_CKS_LOC=131
+default CONFIG_LB_CKS_RANGE_START=128
+default CONFIG_LB_CKS_RANGE_END=130
+default CONFIG_LB_CKS_LOC=131
##
## Build code for SMP support
##
## Motherboard identification
##
-default MAINBOARD_PART_NUMBER="EIDXE7501DEVKIT"
-default MAINBOARD_VENDOR="Intel"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x8086
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2480
+default CONFIG_MAINBOARD_PART_NUMBER="EIDXE7501DEVKIT"
+default CONFIG_MAINBOARD_VENDOR="Intel"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x8086
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2480
###
### coreboot layout values
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE=0x4000
+default CONFIG_HEAP_SIZE=0x4000
##
## CMOS settings not currently supported due to conflicts with factory BIOS
##
-default USE_OPTION_TABLE = 0
+default CONFIG_USE_OPTION_TABLE = 0
##
## Coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00004000
+default CONFIG_RAMBASE=0x00004000
##
## Load the payload from the ROM
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## Disable the gdb stub by default
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
## Things we may not have
default CONFIG_IDE=1
-default DEBUG=1
-# default CPU_OPT="-g"
+default CONFIG_DEBUG=1
+# default CONFIG_CPU_OPT="-g"
### End Options.lb
#
// Get the serial port running and print a welcome banner
- lpc47b272_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ lpc47b272_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/failovercalculation.lb
arch i386 end
#needed by irq_tables and mptable and acpi_tables
object get_bus_conf.o
-if HAVE_MP_TABLE
+if CONFIG_HAVE_MP_TABLE
object mptable.o
end
-if HAVE_PIRQ_TABLE
+if CONFIG_HAVE_PIRQ_TABLE
object irq_tables.o
end
-#if HAVE_ACPI_TABLES
+#if CONFIG_HAVE_ACPI_TABLES
# object acpi_tables.o
# object fadt.o
-# if SB_HT_CHAIN_ON_BUS0
+# if CONFIG_SB_HT_CHAIN_ON_BUS0
# object dsdt_bus0.o
# else
# object dsdt.o
# end
# object ssdt.o
-# if ACPI_SSDTX_NUM
-# if SB_HT_CHAIN_ON_BUS0
+# if CONFIG_ACPI_SSDTX_NUM
+# if CONFIG_SB_HT_CHAIN_ON_BUS0
# object ssdt2_bus0.o
# else
# object ssdt2.o
# end
#end
-if HAVE_ACPI_TABLES
+if CONFIG_HAVE_ACPI_TABLES
object acpi_tables.o
object fadt.o
makerule dsdt.c
- depends "$(MAINBOARD)/dx/dsdt_lb.dsl"
- action "iasl -p $(CURDIR)/dsdt_lb -tc $(MAINBOARD)/dx/dsdt_lb.dsl"
+ depends "$(CONFIG_MAINBOARD)/dx/dsdt_lb.dsl"
+ action "iasl -p $(CURDIR)/dsdt_lb -tc $(CONFIG_MAINBOARD)/dx/dsdt_lb.dsl"
action "mv dsdt_lb.hex dsdt.c"
end
object ./dsdt.o
#./ssdt.o is moved to northbridge/amd/amdk8/Config.lb
- if ACPI_SSDTX_NUM
+ if CONFIG_ACPI_SSDTX_NUM
makerule ssdt2.c
- depends "$(MAINBOARD)/dx/pci2.asl"
- action "iasl -p $(CURDIR)/pci2 -tc $(MAINBOARD)/dx/pci2.asl"
+ depends "$(CONFIG_MAINBOARD)/dx/pci2.asl"
+ action "iasl -p $(CURDIR)/pci2 -tc $(CONFIG_MAINBOARD)/dx/pci2.asl"
action "perl -pi -e 's/AmlCode/AmlCode_ssdt2/g' pci2.hex"
action "mv pci2.hex ssdt2.c"
end
object ./ssdt2.o
makerule ssdt3.c
- depends "$(MAINBOARD)/dx/pci3.asl"
- action "iasl -p $(CURDIR)/pci3 -tc $(MAINBOARD)/dx/pci3.asl"
+ depends "$(CONFIG_MAINBOARD)/dx/pci3.asl"
+ action "iasl -p $(CURDIR)/pci3 -tc $(CONFIG_MAINBOARD)/dx/pci3.asl"
action "perl -pi -e 's/AmlCode/AmlCode_ssdt3/g' pci3.hex"
action "mv pci3.hex ssdt3.c"
end
object ./ssdt3.o
makerule ssdt4.c
- depends "$(MAINBOARD)/dx/pci4.asl"
- action "iasl -p $(CURDIR)/pci4 -tc $(MAINBOARD)/dx/pci4.asl"
+ depends "$(CONFIG_MAINBOARD)/dx/pci4.asl"
+ action "iasl -p $(CURDIR)/pci4 -tc $(CONFIG_MAINBOARD)/dx/pci4.asl"
action "perl -pi -e 's/AmlCode/AmlCode_ssdt4/g' pci4.hex"
action "mv pci4.hex ssdt4.c"
end
object ./ssdt4.o
makerule ssdt5.c
- depends "$(MAINBOARD)/dx/pci5.asl"
- action "iasl -p $(CURDIR)/pci5 -tc $(MAINBOARD)/dx/pci5.asl"
+ depends "$(CONFIG_MAINBOARD)/dx/pci5.asl"
+ action "iasl -p $(CURDIR)/pci5 -tc $(CONFIG_MAINBOARD)/dx/pci5.asl"
action "perl -pi -e 's/AmlCode/AmlCode_ssdt5/g' pci5.hex"
action "mv pci5.hex ssdt5.c"
end
if CONFIG_USE_INIT
# compile cache_as_ram.c to auto.o
makerule ./cache_as_ram_auto.o
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
end
else
#compile cache_as_ram.c to auto.inc
makerule ./cache_as_ram_auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
end
-if USE_FAILOVER_IMAGE
+if CONFIG_USE_FAILOVER_IMAGE
else
if CONFIG_AP_CODE_IN_CAR
makerule ./apc_auto.o
- depends "$(MAINBOARD)/apc_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/apc_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/apc_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/apc_auto.c -o $@"
end
ldscript /arch/i386/init/ldscript_apc.lb
end
## Build our 16 bit and 32 bit coreboot entry code
##
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
end
##
## Build our reset vector (This is where coreboot is entered)
##
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
ldscript /cpu/x86/32bit/reset32.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
ldscript /arch/i386/lib/failover_failover.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
end
end
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses HAVE_ACPI_TABLES
-uses HAVE_ACPI_RESUME
-uses ACPI_SSDTX_NUM
-uses USE_FALLBACK_IMAGE
-uses USE_FAILOVER_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_FAILOVER_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_HAVE_ACPI_TABLES
+uses CONFIG_HAVE_ACPI_RESUME
+uses CONFIG_ACPI_SSDTX_NUM
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_USE_FAILOVER_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_FAILOVER_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_MAX_CPUS
uses CONFIG_MAX_PHYSICAL_CPUS
uses CONFIG_LOGICAL_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses FAILOVER_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_FAILOVER_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
-uses _RAMBASE
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_RAMBASE
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_SERIAL8250
-uses HAVE_INIT_TIMER
+uses CONFIG_HAVE_INIT_TIMER
uses CONFIG_GDB_STUB
uses CONFIG_GDB_STUB
-uses CROSS_COMPILE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
-uses HW_MEM_HOLE_SIZEK
-uses HW_MEM_HOLE_SIZE_AUTO_INC
-uses K8_HT_FREQ_1G_SUPPORT
-
-uses HT_CHAIN_UNITID_BASE
-uses HT_CHAIN_END_UNITID_BASE
-uses SB_HT_CHAIN_ON_BUS0
-uses SB_HT_CHAIN_UNITID_OFFSET_ONLY
-
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
-uses DCACHE_RAM_GLOBAL_VAR_SIZE
+uses CONFIG_HW_MEM_HOLE_SIZEK
+uses CONFIG_HW_MEM_HOLE_SIZE_AUTO_INC
+uses CONFIG_K8_HT_FREQ_1G_SUPPORT
+
+uses CONFIG_HT_CHAIN_UNITID_BASE
+uses CONFIG_HT_CHAIN_END_UNITID_BASE
+uses CONFIG_SB_HT_CHAIN_ON_BUS0
+uses CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY
+
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
+uses CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE
uses CONFIG_USE_INIT
-uses SERIAL_CPU_INIT
+uses CONFIG_SERIAL_CPU_INIT
-uses ENABLE_APIC_EXT_ID
-uses APIC_ID_OFFSET
-uses LIFT_BSP_APIC_ID
+uses CONFIG_ENABLE_APIC_EXT_ID
+uses CONFIG_APIC_ID_OFFSET
+uses CONFIG_LIFT_BSP_APIC_ID
uses CONFIG_PCI_64BIT_PREF_MEM
uses CONFIG_AP_CODE_IN_CAR
-uses MEM_TRAIN_SEQ
+uses CONFIG_MEM_TRAIN_SEQ
-uses WAIT_BEFORE_CPUS_INIT
+uses CONFIG_WAIT_BEFORE_CPUS_INIT
uses CONFIG_USE_PRINTK_IN_CAR
###
##
-## ROM_SIZE is the size of boot ROM that this board will use.
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
##
-default ROM_SIZE=524288
+default CONFIG_ROM_SIZE=524288
##
-## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
+## CONFIG_FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
##
-#default FALLBACK_SIZE=131072
-#default FALLBACK_SIZE=0x40000
+#default CONFIG_FALLBACK_SIZE=131072
+#default CONFIG_FALLBACK_SIZE=0x40000
#FALLBACK: 256K-8K
-default FALLBACK_SIZE=0x3e000
+default CONFIG_FALLBACK_SIZE=0x3e000
#FAILOVER: 8K
-default FAILOVER_SIZE=0x02000
+default CONFIG_FAILOVER_SIZE=0x02000
#more 1M for pgtbl
default CONFIG_LB_MEM_TOPK=2048
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
-default HAVE_FAILOVER_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FAILOVER_BOOT=1
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=11
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=11
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
## ACPI tables will be included
-default HAVE_ACPI_TABLES=1
+default CONFIG_HAVE_ACPI_TABLES=1
## extra SSDT num
-default ACPI_SSDTX_NUM=3
+default CONFIG_ACPI_SSDTX_NUM=3
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
##
## Move the default coreboot cmos range off of AMD RTC registers
##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
+default CONFIG_LB_CKS_RANGE_START=49
+default CONFIG_LB_CKS_RANGE_END=122
+default CONFIG_LB_CKS_LOC=123
##
## Build code for SMP support
default CONFIG_MAX_PHYSICAL_CPUS=2
default CONFIG_LOGICAL_CPUS=1
-default SERIAL_CPU_INIT=0
+default CONFIG_SERIAL_CPU_INIT=0
-default ENABLE_APIC_EXT_ID=0
-default APIC_ID_OFFSET=0x10
-default LIFT_BSP_APIC_ID=1
+default CONFIG_ENABLE_APIC_EXT_ID=0
+default CONFIG_APIC_ID_OFFSET=0x10
+default CONFIG_LIFT_BSP_APIC_ID=1
#memory hole size, 0 mean disable, others will enable the hole, at that case if it is small than mmio_basek, it will use mmio_basek instead.
#2G
-#default HW_MEM_HOLE_SIZEK=0x200000
+#default CONFIG_HW_MEM_HOLE_SIZEK=0x200000
#1G
-#default HW_MEM_HOLE_SIZEK=0x100000
+#default CONFIG_HW_MEM_HOLE_SIZEK=0x100000
#512M
-default HW_MEM_HOLE_SIZEK=0x80000
+default CONFIG_HW_MEM_HOLE_SIZEK=0x80000
#make auto increase hole size to avoid hole_startk equal to basek so as to make some kernel happy
-#default HW_MEM_HOLE_SIZE_AUTO_INC=1
+#default CONFIG_HW_MEM_HOLE_SIZE_AUTO_INC=1
#Opteron K8 1G HT Support
-default K8_HT_FREQ_1G_SUPPORT=1
+default CONFIG_K8_HT_FREQ_1G_SUPPORT=1
#VGA Console
default CONFIG_CONSOLE_VGA=1
default CONFIG_PCI_ROM_RUN=1
#HT Unit ID offset, default is 1, the typical one
-default HT_CHAIN_UNITID_BASE=0xa
+default CONFIG_HT_CHAIN_UNITID_BASE=0xa
#real SB Unit ID, default is 0x20, mean dont touch it at last
-default HT_CHAIN_END_UNITID_BASE=0x6
+default CONFIG_HT_CHAIN_END_UNITID_BASE=0x6
#make the SB HT chain on bus 0, default is not (0)
-default SB_HT_CHAIN_ON_BUS0=2
+default CONFIG_SB_HT_CHAIN_ON_BUS0=2
#only offset for SB chain?, default is yes(1)
-#default SB_HT_CHAIN_UNITID_OFFSET_ONLY=0
+#default CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY=0
#allow capable device use that above 4G
#default CONFIG_PCI_64BIT_PREF_MEM=1
##
## enable CACHE_AS_RAM specifics
##
-default USE_DCACHE_RAM=1
-default DCACHE_RAM_BASE=0xc4000
-default DCACHE_RAM_SIZE=0x0c000
-default DCACHE_RAM_GLOBAL_VAR_SIZE=0x01000
+default CONFIG_USE_DCACHE_RAM=1
+default CONFIG_DCACHE_RAM_BASE=0xc4000
+default CONFIG_DCACHE_RAM_SIZE=0x0c000
+default CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE=0x01000
default CONFIG_USE_INIT=0
##
## for rev F training on AP purpose
##
#default CONFIG_AP_CODE_IN_CAR=1
-#default MEM_TRAIN_SEQ=1
-#default WAIT_BEFORE_CPUS_INIT=1
+#default CONFIG_MEM_TRAIN_SEQ=1
+#default CONFIG_WAIT_BEFORE_CPUS_INIT=1
##
## Build code to setup a generic IOAPIC
##
## Clean up the motherboard id strings
##
-default MAINBOARD_PART_NUMBER="dk8_htx"
-default MAINBOARD_VENDOR="IWILL"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x1022
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2b80
+default CONFIG_MAINBOARD_PART_NUMBER="dk8_htx"
+default CONFIG_MAINBOARD_VENDOR="IWILL"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x1022
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2b80
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 32K heap
##
-default HEAP_SIZE=0x8000
+default CONFIG_HEAP_SIZE=0x8000
##
## Only use the option table in a normal image
##
-default USE_OPTION_TABLE = (!USE_FALLBACK_IMAGE) && (!USE_FAILOVER_IMAGE )
+default CONFIG_USE_OPTION_TABLE = (!CONFIG_USE_FALLBACK_IMAGE) && (!CONFIG_USE_FAILOVER_IMAGE )
##
## Coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00100000
+default CONFIG_RAMBASE=0x00100000
##
## Load the payload from the ROM
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## Disable the gdb stub by default
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
### End Options.lb
#
extern unsigned char AmlCode[];
-#if ACPI_SSDTX_NUM >= 1
+#if CONFIG_ACPI_SSDTX_NUM >= 1
extern unsigned char AmlCode_ssdt2[];
extern unsigned char AmlCode_ssdt3[];
extern unsigned char AmlCode_ssdt4[];
current += ssdt->length;
acpi_add_table(rsdt, ssdt);
-#if ACPI_SSDTX_NUM >= 1
+#if CONFIG_ACPI_SSDTX_NUM >= 1
//same htio, but different position? We may have to copy, change HCIN, and recalculate the checknum and add_table
//if we want to wait for core1 done before DQS training, set it to 0
#define K8_SET_FIDVID_CORE0_ONLY 1
-#if K8_REV_F_SUPPORT == 1
+#if CONFIG_K8_REV_F_SUPPORT == 1
#define K8_REV_F_SUPPORT_F0_F1_WORKAROUND 0
#endif
#include "option_table.h"
#include "pc80/mc146818rtc_early.c"
-#if USE_FAILOVER_IMAGE==0
+#if CONFIG_USE_FAILOVER_IMAGE==0
#include "pc80/serial.c"
#include "arch/i386/lib/console.c"
#include <cpu/amd/model_fxx_rev.h>
#include "cpu/x86/lapic/boot_cpu.c"
#include "northbridge/amd/amdk8/reset_test.c"
-#if USE_FAILOVER_IMAGE==0
+#if CONFIG_USE_FAILOVER_IMAGE==0
#include "cpu/x86/bist.h"
#include "lib/delay.c"
#include "cpu/amd/model_fxx/fidvid.c"
#endif
-#if ((HAVE_FAILOVER_BOOT==1) && (USE_FAILOVER_IMAGE == 1)) || ((HAVE_FAILOVER_BOOT==0) && (USE_FALLBACK_IMAGE == 1))
+#if ((CONFIG_HAVE_FAILOVER_BOOT==1) && (CONFIG_USE_FAILOVER_IMAGE == 1)) || ((CONFIG_HAVE_FAILOVER_BOOT==0) && (CONFIG_USE_FALLBACK_IMAGE == 1))
#include "southbridge/amd/amd8111/amd8111_enable_rom.c"
#include "northbridge/amd/amdk8/early_ht.c"
);
fallback_image:
-#if HAVE_FAILOVER_BOOT==1
+#if CONFIG_HAVE_FAILOVER_BOOT==1
__asm__ volatile ("jmp __fallback_image"
: /* outputs */
: "a" (bist), "b" (cpu_init_detectedx) /* inputs */
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
-#if HAVE_FAILOVER_BOOT==1
- #if USE_FAILOVER_IMAGE==1
+#if CONFIG_HAVE_FAILOVER_BOOT==1
+ #if CONFIG_USE_FAILOVER_IMAGE==1
failover_process(bist, cpu_init_detectedx);
#else
real_main(bist, cpu_init_detectedx);
#endif
#else
- #if USE_FALLBACK_IMAGE == 1
+ #if CONFIG_USE_FALLBACK_IMAGE == 1
failover_process(bist, cpu_init_detectedx);
#endif
real_main(bist, cpu_init_detectedx);
#endif
}
-#if USE_FAILOVER_IMAGE==0
+#if CONFIG_USE_FAILOVER_IMAGE==0
void real_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
};
- struct sys_info *sysinfo = (DCACHE_RAM_BASE + DCACHE_RAM_SIZE - DCACHE_RAM_GLOBAL_VAR_SIZE);
+ struct sys_info *sysinfo = (CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE);
int needs_reset; int i;
unsigned bsp_apicid = 0;
bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);
}
- w83627hf_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ w83627hf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
print_debug("bsp_apicid="); print_debug_hex8(bsp_apicid); print_debug("\r\n");
-#if MEM_TRAIN_SEQ == 1
+#if CONFIG_MEM_TRAIN_SEQ == 1
set_sysinfo_in_ram(0); // in BSP so could hold all ap until sysinfo is in ram
#endif
setup_coherent_ht_domain(); // routing table and start other core0
dev = dev_find_slot(m->bus_8111_0, PCI_DEVFN(sysconf.sbdn,0));
if (dev) {
m->bus_8111_1 = pci_read_config8(dev, PCI_SECONDARY_BUS);
-#if HT_CHAIN_END_UNITID_BASE >= HT_CHAIN_UNITID_BASE
+#if CONFIG_HT_CHAIN_END_UNITID_BASE >= CONFIG_HT_CHAIN_UNITID_BASE
m->bus_isa = pci_read_config8(dev, PCI_SUBORDINATE_BUS);
m->bus_isa++;
// printk_debug("bus_isa=%d\n",bus_isa);
dev = dev_find_slot(m->bus_8132_0, PCI_DEVFN(m->sbdn3+1,0));
if (dev) {
m->bus_8132_2 = pci_read_config8(dev, PCI_SECONDARY_BUS);
-#if HT_CHAIN_END_UNITID_BASE < HT_CHAIN_UNITID_BASE
+#if CONFIG_HT_CHAIN_END_UNITID_BASE < CONFIG_HT_CHAIN_UNITID_BASE
m->bus_isa = pci_read_config8(dev, PCI_SUBORDINATE_BUS);
m->bus_isa++;
// printk_debug("bus_isa=%d\n",bus_isa);
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
##
##
driver mainboard.o
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
#object reset.o
## ATI Rage XL framebuffering graphics driver
if CONFIG_USE_INIT
makerule ./auto.o
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
end
else
makerule ./auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
##
## Build our 16 bit and 32 bit coreboot entry code
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
end
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
end
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_MAX_CPUS
uses CONFIG_MAX_PHYSICAL_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
-uses _RAMBASE
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_RAMBASE
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_SERIAL8250
-uses HAVE_INIT_TIMER
+uses CONFIG_HAVE_INIT_TIMER
uses CONFIG_GDB_STUB
-uses CROSS_COMPILE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
uses CONFIG_USE_INIT
uses CONFIG_USE_PRINTK_IN_CAR
-## ROM_SIZE is the size of boot ROM that this board will use.
-default ROM_SIZE=524288
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
+default CONFIG_ROM_SIZE=524288
###
### Build options
###
##
-## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
+## CONFIG_FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
##
-default FALLBACK_SIZE=0x40000
+default CONFIG_FALLBACK_SIZE=0x40000
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=9
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=9
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
##
## Move the default coreboot cmos range off of AMD RTC registers
##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
+default CONFIG_LB_CKS_RANGE_START=49
+default CONFIG_LB_CKS_RANGE_END=122
+default CONFIG_LB_CKS_LOC=123
##
## Build code for SMP support
##
## enable CACHE_AS_RAM specifics
##
-default USE_DCACHE_RAM=1
-default DCACHE_RAM_BASE=0xcf000
-default DCACHE_RAM_SIZE=0x1000
+default CONFIG_USE_DCACHE_RAM=1
+default CONFIG_DCACHE_RAM_BASE=0xcf000
+default CONFIG_DCACHE_RAM_SIZE=0x1000
default CONFIG_USE_INIT=0
##
## Clean up the motherboard id strings
##
-default MAINBOARD_PART_NUMBER="HDAMA"
-default MAINBOARD_VENDOR="ARIMA"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x161f
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x3016
+default CONFIG_MAINBOARD_PART_NUMBER="HDAMA"
+default CONFIG_MAINBOARD_VENDOR="ARIMA"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x161f
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x3016
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE=0x4000
+default CONFIG_HEAP_SIZE=0x4000
##
## Only use the option table in a normal image
##
-default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
##
## Coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00004000
+default CONFIG_RAMBASE=0x00004000
##
## Load the payload from the ROM
##
## The default compiler
##
-#default CC="$(CROSS_COMPILE)gcc -m32"
-#default HOSTCC="gcc"
+#default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+#default CONFIG_HOSTCC="gcc"
##
## Disable the gdb stub by default
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
### End Options.lb
#
//if we want to wait for core1 done before DQS training, set it to 0
#define K8_SET_FIDVID_CORE0_ONLY 1
-#if K8_REV_F_SUPPORT == 1
+#if CONFIG_K8_REV_F_SUPPORT == 1
#define K8_REV_F_SUPPORT_F0_F1_WORKAROUND 0
#endif
#include "option_table.h"
#include "pc80/mc146818rtc_early.c"
-#if USE_FAILOVER_IMAGE==0
+#if CONFIG_USE_FAILOVER_IMAGE==0
#include "pc80/serial.c"
#include "arch/i386/lib/console.c"
#include <cpu/amd/model_fxx_rev.h>
#include "cpu/x86/lapic/boot_cpu.c"
#include "northbridge/amd/amdk8/reset_test.c"
-#if USE_FAILOVER_IMAGE==0
+#if CONFIG_USE_FAILOVER_IMAGE==0
#include "cpu/x86/bist.h"
#include "lib/delay.c"
#include "cpu/amd/model_fxx/fidvid.c"
#endif
-#if ((HAVE_FAILOVER_BOOT==1) && (USE_FAILOVER_IMAGE == 1)) || ((HAVE_FAILOVER_BOOT==0) && (USE_FALLBACK_IMAGE == 1))
+#if ((CONFIG_HAVE_FAILOVER_BOOT==1) && (CONFIG_USE_FAILOVER_IMAGE == 1)) || ((CONFIG_HAVE_FAILOVER_BOOT==0) && (CONFIG_USE_FALLBACK_IMAGE == 1))
#include "southbridge/amd/amd8111/amd8111_enable_rom.c"
#include "northbridge/amd/amdk8/early_ht.c"
);
fallback_image:
-#if HAVE_FAILOVER_BOOT==1
+#if CONFIG_HAVE_FAILOVER_BOOT==1
__asm__ volatile ("jmp __fallback_image"
: /* outputs */
: "a" (bist), "b" (cpu_init_detectedx) /* inputs */
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
-#if HAVE_FAILOVER_BOOT==1
- #if USE_FAILOVER_IMAGE==1
+#if CONFIG_HAVE_FAILOVER_BOOT==1
+ #if CONFIG_USE_FAILOVER_IMAGE==1
failover_process(bist, cpu_init_detectedx);
#else
real_main(bist, cpu_init_detectedx);
#endif
#else
- #if USE_FALLBACK_IMAGE == 1
+ #if CONFIG_USE_FALLBACK_IMAGE == 1
failover_process(bist, cpu_init_detectedx);
#endif
real_main(bist, cpu_init_detectedx);
#endif
}
-#if USE_FAILOVER_IMAGE==0
+#if CONFIG_USE_FAILOVER_IMAGE==0
void real_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
};
- struct sys_info *sysinfo = (DCACHE_RAM_BASE + DCACHE_RAM_SIZE - DCACHE_RAM_GLOBAL_VAR_SIZE);
+ struct sys_info *sysinfo = (CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE);
int needs_reset; int i;
unsigned bsp_apicid = 0;
bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);
}
- w83627hf_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ w83627hf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
print_debug("bsp_apicid="); print_debug_hex8(bsp_apicid); print_debug("\r\n");
-#if MEM_TRAIN_SEQ == 1
+#if CONFIG_MEM_TRAIN_SEQ == 1
set_sysinfo_in_ram(0); // in BSP so could hold all ap until sysinfo is in ram
#endif
setup_coherent_ht_domain(); // routing table and start other core0
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
##
##
driver mainboard.o
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
#object reset.o
if CONFIG_USE_INIT
makerule ./auto.o
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
end
else
makerule ./auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
##
## Build our 16 bit and 32 bit coreboot entry code
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
end
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
end
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_MAX_CPUS
uses CONFIG_MAX_PHYSICAL_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
-uses _RAMBASE
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_RAMBASE
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_SERIAL8250
-uses HAVE_INIT_TIMER
+uses CONFIG_HAVE_INIT_TIMER
uses CONFIG_GDB_STUB
-uses CROSS_COMPILE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
uses CONFIG_USE_INIT
uses CONFIG_USE_PRINTK_IN_CAR
-## ROM_SIZE is the size of boot ROM that this board will use.
-default ROM_SIZE=524288
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
+default CONFIG_ROM_SIZE=524288
###
### Build options
###
##
-## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
+## CONFIG_FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
##
-default FALLBACK_SIZE=131072
+default CONFIG_FALLBACK_SIZE=131072
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=9
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=9
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
##
## Move the default coreboot cmos range off of AMD RTC registers
##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
+default CONFIG_LB_CKS_RANGE_START=49
+default CONFIG_LB_CKS_RANGE_END=122
+default CONFIG_LB_CKS_LOC=123
##
## Build code for SMP support
##
## enable CACHE_AS_RAM specifics
##
-default USE_DCACHE_RAM=1
-default DCACHE_RAM_BASE=0xcf000
-default DCACHE_RAM_SIZE=0x1000
+default CONFIG_USE_DCACHE_RAM=1
+default CONFIG_DCACHE_RAM_BASE=0xcf000
+default CONFIG_DCACHE_RAM_SIZE=0x1000
default CONFIG_USE_INIT=0
##
## Clean up the motherboard id strings
##
-#default MAINBOARD_PART_NUMBER="HDAMA"
-#default MAINBOARD_VENDOR="ARIMA"
-#default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x161f
-#default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x3016
+#default CONFIG_MAINBOARD_PART_NUMBER="HDAMA"
+#default CONFIG_MAINBOARD_VENDOR="ARIMA"
+#default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x161f
+#default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x3016
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE=0x4000
+default CONFIG_HEAP_SIZE=0x4000
##
## Only use the option table in a normal image
##
-default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
##
## Coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00004000
+default CONFIG_RAMBASE=0x00004000
##
## Load the payload from the ROM
##
## The default compiler
##
-#default CC="$(CROSS_COMPILE)gcc -m32"
-#default HOSTCC="gcc"
+#default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+#default CONFIG_HOSTCC="gcc"
##
## Disable the gdb stub by default
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
### End Options.lb
#
//if we want to wait for core1 done before DQS training, set it to 0
#define K8_SET_FIDVID_CORE0_ONLY 1
-#if K8_REV_F_SUPPORT == 1
+#if CONFIG_K8_REV_F_SUPPORT == 1
#define K8_REV_F_SUPPORT_F0_F1_WORKAROUND 0
#endif
#include "option_table.h"
#include "pc80/mc146818rtc_early.c"
-#if USE_FAILOVER_IMAGE==0
+#if CONFIG_USE_FAILOVER_IMAGE==0
#include "pc80/serial.c"
#include "arch/i386/lib/console.c"
#include <cpu/amd/model_fxx_rev.h>
#include "cpu/x86/lapic/boot_cpu.c"
#include "northbridge/amd/amdk8/reset_test.c"
-#if USE_FAILOVER_IMAGE==0
+#if CONFIG_USE_FAILOVER_IMAGE==0
#include "cpu/x86/bist.h"
#include "lib/delay.c"
#include "cpu/amd/model_fxx/fidvid.c"
#endif
-#if ((HAVE_FAILOVER_BOOT==1) && (USE_FAILOVER_IMAGE == 1)) || ((HAVE_FAILOVER_BOOT==0) && (USE_FALLBACK_IMAGE == 1))
+#if ((CONFIG_HAVE_FAILOVER_BOOT==1) && (CONFIG_USE_FAILOVER_IMAGE == 1)) || ((CONFIG_HAVE_FAILOVER_BOOT==0) && (CONFIG_USE_FALLBACK_IMAGE == 1))
#include "southbridge/amd/amd8111/amd8111_enable_rom.c"
#include "northbridge/amd/amdk8/early_ht.c"
);
fallback_image:
-#if HAVE_FAILOVER_BOOT==1
+#if CONFIG_HAVE_FAILOVER_BOOT==1
__asm__ volatile ("jmp __fallback_image"
: /* outputs */
: "a" (bist), "b" (cpu_init_detectedx) /* inputs */
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
-#if HAVE_FAILOVER_BOOT==1
- #if USE_FAILOVER_IMAGE==1
+#if CONFIG_HAVE_FAILOVER_BOOT==1
+ #if CONFIG_USE_FAILOVER_IMAGE==1
failover_process(bist, cpu_init_detectedx);
#else
real_main(bist, cpu_init_detectedx);
#endif
#else
- #if USE_FALLBACK_IMAGE == 1
+ #if CONFIG_USE_FALLBACK_IMAGE == 1
failover_process(bist, cpu_init_detectedx);
#endif
real_main(bist, cpu_init_detectedx);
#endif
}
-#if USE_FAILOVER_IMAGE==0
+#if CONFIG_USE_FAILOVER_IMAGE==0
void real_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
};
- struct sys_info *sysinfo = (DCACHE_RAM_BASE + DCACHE_RAM_SIZE - DCACHE_RAM_GLOBAL_VAR_SIZE);
+ struct sys_info *sysinfo = (CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE);
int needs_reset; int i;
unsigned bsp_apicid = 0;
bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);
}
- w83627hf_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ w83627hf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
print_debug("bsp_apicid="); print_debug_hex8(bsp_apicid); print_debug("\r\n");
-#if MEM_TRAIN_SEQ == 1
+#if CONFIG_MEM_TRAIN_SEQ == 1
set_sysinfo_in_ram(0); // in BSP so could hold all ap until sysinfo is in ram
#endif
setup_coherent_ht_domain(); // routing table and start other core0
const struct irq_routing_table intel_irq_routing_table = {
PIRQ_SIGNATURE, /* u32 signature */
PIRQ_VERSION, /* u16 version */
- 32+16*IRQ_SLOT_COUNT, /* there can be total IRQ_SLOT_COUNT
+ 32+16*CONFIG_IRQ_SLOT_COUNT, /* there can be total CONFIG_IRQ_SLOT_COUNT
* devices on the bus */
IRQ_ROUTER_BUS, /* Where the interrupt router lies (bus) */
IRQ_ROUTER_DEVFN, /* Where the interrupt router lies (dev) */
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
arch i386 end
driver mainboard.o
-if HAVE_PIRQ_TABLE object irq_tables.o end
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_ACPI_TABLES
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_ACPI_TABLES
object fadt.o
object dsdt.o
object acpi_tables.o
end
makerule ./failover.E
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./auto.E
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -E -mcpu=c3 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -E -mcpu=c3 -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -mcpu=c3 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -mcpu=c3 -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
mainboardinit cpu/x86/16bit/entry16.inc
mainboardinit cpu/x86/32bit/entry32.inc
ldscript /cpu/x86/16bit/entry16.lds
ldscript /cpu/x86/32bit/entry32.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
mainboardinit arch/i386/lib/cpu_reset.inc
mainboardinit arch/i386/lib/id.inc
ldscript /arch/i386/lib/id.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_ROM_PAYLOAD
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_NRV2B
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses HAVE_MP_TABLE
-uses HAVE_ACPI_TABLES
-uses HAVE_ACPI_RESUME
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_HAVE_ACPI_TABLES
+uses CONFIG_HAVE_ACPI_RESUME
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
uses CONFIG_PCI_ROM_RUN
uses CONFIG_CONSOLE_VGA
uses CONFIG_MAX_PCI_BUSES
-uses TTYS0_BAUD
+uses CONFIG_TTYS0_BAUD
uses CONFIG_VIDEO_MB
uses CONFIG_IOAPIC
-default ROM_SIZE = 512 * 1024
+default CONFIG_ROM_SIZE = 512 * 1024
default CONFIG_IOAPIC = 0
default CONFIG_VIDEO_MB = 32
default CONFIG_CONSOLE_SERIAL8250 = 1
default CONFIG_PCI_ROM_RUN = 0
default CONFIG_CONSOLE_VGA = 0
-default HAVE_FALLBACK_BOOT = 1
-default HAVE_MP_TABLE = 0
+default CONFIG_HAVE_FALLBACK_BOOT = 1
+default CONFIG_HAVE_MP_TABLE = 0
default CONFIG_UDELAY_TSC = 1
default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 1
-default HAVE_HARD_RESET = 0
-default HAVE_PIRQ_TABLE = 1
-default IRQ_SLOT_COUNT = 10
-default HAVE_ACPI_TABLES = 0
-default HAVE_OPTION_TABLE = 0
-default ROM_IMAGE_SIZE = 64 * 1024
-default FALLBACK_SIZE = ROM_SIZE
-default USE_FALLBACK_IMAGE = 1
-default STACK_SIZE = 8 * 1024
-default HEAP_SIZE = 16 * 1024
-default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-#default USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_HAVE_HARD_RESET = 0
+default CONFIG_HAVE_PIRQ_TABLE = 1
+default CONFIG_IRQ_SLOT_COUNT = 10
+default CONFIG_HAVE_ACPI_TABLES = 0
+default CONFIG_HAVE_OPTION_TABLE = 0
+default CONFIG_ROM_IMAGE_SIZE = 64 * 1024
+default CONFIG_FALLBACK_SIZE = CONFIG_ROM_SIZE
+default CONFIG_USE_FALLBACK_IMAGE = 1
+default CONFIG_STACK_SIZE = 8 * 1024
+default CONFIG_HEAP_SIZE = 16 * 1024
+default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+#default CONFIG_USE_OPTION_TABLE = 0
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
-default CROSS_COMPILE = ""
-default CC = "$(CROSS_COMPILE)gcc -m32 -fno-stack-protector"
-default HOSTCC = "gcc"
+default CONFIG_CROSS_COMPILE = ""
+default CC = "$(CONFIG_CROSS_COMPILE)gcc -m32 -fno-stack-protector"
+default CONFIG_HOSTCC = "gcc"
##
## Set this to the max PCI bus number you would ever use for PCI config I/O.
#include "southbridge/via/vt8237r/vt8237r_early_smbus.c"
#include "superio/fintek/f71805f/f71805f_early_serial.c"
-#if TTYS0_BASE == 0x2f8
+#if CONFIG_TTYS0_BASE == 0x2f8
#define SERIAL_DEV PNP_DEV(0x2e, F71805F_SP2)
#else
#define SERIAL_DEV PNP_DEV(0x2e, F71805F_SP1)
/* Enable multifunction for northbridge. */
pci_write_config8(ctrl.d0f0, 0x4f, 0x01);
- f71805f_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ f71805f_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
const struct irq_routing_table intel_irq_routing_table = {
PIRQ_SIGNATURE,
PIRQ_VERSION,
- 32 + 16 * IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
+ 32 + 16 * CONFIG_IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
0x00, /* Interrupt router bus */
(0x11 << 3) | 0x0, /* Interrupt router device */
0x828, /* IRQs devoted exclusively to PCI usage */
##
## Only use the option table in a normal image
##
-default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
##
driver mainboard.o
driver rtl8168.o
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE object irq_tables.o end
-if HAVE_SMI_HANDLER smmobject mainboard_smi.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_SMI_HANDLER smmobject mainboard_smi.o end
-if HAVE_ACPI_TABLES
+if CONFIG_HAVE_ACPI_TABLES
object fadt.o
object acpi_tables.o
makerule dsdt.c
- depends "$(MAINBOARD)/dsdt.asl"
- action "iasl -p dsdt -tc $(MAINBOARD)/dsdt.asl"
+ depends "$(CONFIG_MAINBOARD)/dsdt.asl"
+ action "iasl -p dsdt -tc $(CONFIG_MAINBOARD)/dsdt.asl"
action "mv $(CURDIR)/dsdt.hex dsdt.c"
end
object ./dsdt.o
if CONFIG_USE_INIT
makerule ./auto.o
- depends "$(MAINBOARD)/auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/auto.c -o $@"
end
else
makerule ./auto.inc
- depends "$(MAINBOARD)/auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
end
##
# Tables
-uses HAVE_MP_TABLE
-uses HAVE_PIRQ_TABLE
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses HAVE_ACPI_TABLES
-uses HAVE_ACPI_RESUME
-uses HAVE_MAINBOARD_RESOURCES
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_HAVE_ACPI_TABLES
+uses CONFIG_HAVE_ACPI_RESUME
+uses CONFIG_HAVE_MAINBOARD_RESOURCES
# SMP
uses CONFIG_SMP
uses CONFIG_LOGICAL_CPUS
uses CONFIG_MAX_PHYSICAL_CPUS
uses CONFIG_IOAPIC
# Image Size
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses FALLBACK_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
# Payload
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
+uses CONFIG_PAYLOAD_SIZE
# Build Internals
-uses _RAMBASE
-uses _ROMBASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
+uses CONFIG_RAMBASE
+uses CONFIG_ROMBASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
uses CONFIG_USE_INIT
uses CONFIG_USE_PRINTK_IN_CAR
-uses XIP_ROM_BASE
-uses XIP_ROM_SIZE
-uses HAVE_HARD_RESET
-uses HAVE_SMI_HANDLER
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_SMI_HANDLER
uses CONFIG_PCIE_CONFIGSPACE_HOLE
-uses MMCONF_SUPPORT
-uses MMCONF_BASE_ADDRESS
+uses CONFIG_MMCONF_SUPPORT
+uses CONFIG_MMCONF_BASE_ADDRESS
uses CONFIG_GFXUMA
uses CONFIG_CBFS
#
-uses MAINBOARD
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
# Timers
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
# Console
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_VGA
uses CONFIG_VGA_ROM_RUN
uses CONFIG_PCI_ROM_RUN
-uses DEBUG
+uses CONFIG_DEBUG
# Toolchain
uses CC
-uses HOSTCC
-uses CROSS_COMPILE
-uses OBJCOPY
+uses CONFIG_HOSTCC
+uses CONFIG_CROSS_COMPILE
+uses CONFIG_OBJCOPY
# Tweaks
uses CONFIG_GDB_STUB
-uses MAX_REBOOT_CNT
-uses USE_WATCHDOG_ON_BOOT
+uses CONFIG_MAX_REBOOT_CNT
+uses CONFIG_USE_WATCHDOG_ON_BOOT
uses COREBOOT_EXTRA_VERSION
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
###
### Build options
##
##
-default MAX_REBOOT_CNT=3
+default CONFIG_MAX_REBOOT_CNT=3
##
## Use the watchdog to break out of a lockup condition
##
-default USE_WATCHDOG_ON_BOOT=0
+default CONFIG_USE_WATCHDOG_ON_BOOT=0
##
-## ROM_SIZE is the size of boot ROM that this board will use.
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
##
-default ROM_SIZE=1024*1024
+default CONFIG_ROM_SIZE=1024*1024
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## Delay timer options
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
##
## Build SMI handler
##
-default HAVE_SMI_HANDLER=1
+default CONFIG_HAVE_SMI_HANDLER=1
##
## Leave a hole for mmapped PCIe config space
##
default CONFIG_PCIE_CONFIGSPACE_HOLE=1
-default MMCONF_SUPPORT=1
-default MMCONF_BASE_ADDRESS=0xf0000000
+default CONFIG_MMCONF_SUPPORT=1
+default CONFIG_MMCONF_BASE_ADDRESS=0xf0000000
##
## UMA
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=18
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=18
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
##
## Build code to provide ACPI support
##
-default HAVE_ACPI_TABLES=1
-default HAVE_MAINBOARD_RESOURCES=1
+default CONFIG_HAVE_ACPI_TABLES=1
+default CONFIG_HAVE_MAINBOARD_RESOURCES=1
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
##
## Move the default coreboot cmos range off of AMD RTC registers
##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
+default CONFIG_LB_CKS_RANGE_START=49
+default CONFIG_LB_CKS_RANGE_END=122
+default CONFIG_LB_CKS_LOC=123
#VGA Console
default CONFIG_CONSOLE_VGA=1
# for now:
default CONFIG_VGA_ROM_RUN=1
default CONFIG_PCI_ROM_RUN=0
-default DEBUG=0
+default CONFIG_DEBUG=0
##
## Build code for SMP support
##
## enable CACHE_AS_RAM specifics
##
-default USE_DCACHE_RAM=1
-default DCACHE_RAM_SIZE=0x8000
-default DCACHE_RAM_BASE=( 0xfff00000 - DCACHE_RAM_SIZE - 1024*1024)
+default CONFIG_USE_DCACHE_RAM=1
+default CONFIG_DCACHE_RAM_SIZE=0x8000
+default CONFIG_DCACHE_RAM_BASE=( 0xfff00000 - CONFIG_DCACHE_RAM_SIZE - 1024*1024)
default CONFIG_USE_PRINTK_IN_CAR=1
##
##
## Clean up the motherboard id strings
##
-default MAINBOARD_PART_NUMBER="986LCD-M"
-default MAINBOARD_VENDOR= "KONTRON"
+default CONFIG_MAINBOARD_PART_NUMBER="986LCD-M"
+default CONFIG_MAINBOARD_VENDOR= "KONTRON"
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 32K heap
##
-default HEAP_SIZE=0x8000
+default CONFIG_HEAP_SIZE=0x8000
###
### Compute the location and size of where this firmware image
### (coreboot plus bootloader) will live in the boot rom chip.
###
-default FALLBACK_SIZE=ROM_IMAGE_SIZE
+default CONFIG_FALLBACK_SIZE=CONFIG_ROM_IMAGE_SIZE
##
## coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00100000
+default CONFIG_RAMBASE=0x00100000
##
## Load the payload from the ROM
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## Disable the gdb stub by default
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=5
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=5
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=9
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=9
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
#
# CBFS
printk_debug("ACPI: * DMI (Linux workaround)\n");
memcpy((void *)0xfff80, dmi_table, DMI_TABLE_SIZE);
-#if HAVE_HIGH_TABLES == 1
+#if CONFIG_HAVE_HIGH_TABLES == 1
memcpy((void *)current, dmi_table, DMI_TABLE_SIZE);
current += DMI_TABLE_SIZE;
ALIGN_CURRENT;
RCBA32(0x2034) = reg32;
}
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
#include "southbridge/intel/i82801gx/cmos_failover.c"
#endif
/* Enable SPD ROMs and DDR-II DRAM */
enable_smbus();
-#if DEFAULT_CONSOLE_LOGLEVEL > 8
+#if CONFIG_DEFAULT_CONSOLE_LOGLEVEL > 8
dump_spd_registers();
#endif
/* Initialize the internal PCIe links before we go into stage2 */
i945_late_initialization();
-#if DEFAULT_CONSOLE_LOGLEVEL > 8
+#if CONFIG_DEFAULT_CONSOLE_LOGLEVEL > 8
#if defined(DEBUG_RAM_SETUP)
sdram_dump_mchbar_registers();
#endif
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
##
driver mainboard.o
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
#object reset.o
##
## Romcc output
##
makerule ./failover.E
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./auto.E
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -E -mcpu=i386 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -E -mcpu=i386 -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -mcpu=i386 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -mcpu=i386 -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
##
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_ROM_PAYLOAD
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses HAVE_MP_TABLE
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
-## ROM_SIZE is the size of boot ROM that this board will use.
-default ROM_SIZE = 256*1024
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
+default CONFIG_ROM_SIZE = 256*1024
###
### Build options
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## no MP table
##
-default HAVE_MP_TABLE=0
+default CONFIG_HAVE_MP_TABLE=0
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=0
+default CONFIG_HAVE_HARD_RESET=0
## Delay timer options
##
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=2
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=2
#object irq_tables.o
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=0
+default CONFIG_HAVE_OPTION_TABLE=0
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
-default FALLBACK_SIZE = 131072
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
+default CONFIG_FALLBACK_SIZE = 131072
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE=0x4000
+default CONFIG_HEAP_SIZE=0x4000
##
## Only use the option table in a normal image
##
-#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
+#default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
##
## The default compiler
##
-default CROSS_COMPILE=""
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CONFIG_CROSS_COMPILE=""
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## The Serial Console
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
#
SystemPreInit();
msr_init();
- w83627hf_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ w83627hf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
## Based on Config.lb from AMD's DB800 and DBM690T mainboards.
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
##
driver mainboard.o
-if HAVE_PIRQ_TABLE
+if CONFIG_HAVE_PIRQ_TABLE
object irq_tables.o
end
# compile cache_as_ram.c to auto.inc
makerule ./cache_as_ram_auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/.rodata/.rom.data/g' -pi $@"
action "perl -e 's/.text/.section .rom.text/g' -pi $@"
end
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
# mainboardinit ./failover.inc
end
## Based on Options.lb from AMD's DB800 mainboard.
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_ROM_PAYLOAD
uses CONFIG_IDE
uses CONFIG_FS_PAYLOAD
uses CONFIG_FS_EXT2
-uses AUTOBOOT_DELAY
-uses AUTOBOOT_CMDLINE
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_AUTOBOOT_DELAY
+uses CONFIG_AUTOBOOT_CMDLINE
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESS
uses CONFIG_COMPRESSED_PAYLOAD_NRV2B
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses HAVE_MP_TABLE
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses DEBUG
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_DEBUG
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
uses CONFIG_VIDEO_MB
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
uses CONFIG_USE_PRINTK_IN_CAR
-uses PIRQ_ROUTE
+uses CONFIG_PIRQ_ROUTE
-## ROM_SIZE is the size of boot ROM that this board will use.
-default ROM_SIZE = 512 * 1024
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
+default CONFIG_ROM_SIZE = 512 * 1024
###
### Build options
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT = 1
+default CONFIG_HAVE_FALLBACK_BOOT = 1
##
## no MP table
##
-default HAVE_MP_TABLE = 0
+default CONFIG_HAVE_MP_TABLE = 0
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET = 0
+default CONFIG_HAVE_HARD_RESET = 0
## Delay timer options
##
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE = 1
-default IRQ_SLOT_COUNT = 7
-default PIRQ_ROUTE = 1
+default CONFIG_HAVE_PIRQ_TABLE = 1
+default CONFIG_IRQ_SLOT_COUNT = 7
+default CONFIG_PIRQ_ROUTE = 1
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE = 0
+default CONFIG_HAVE_OPTION_TABLE = 0
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 64 * 1024
-default FALLBACK_SIZE = 128 * 1024
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 64 * 1024
+default CONFIG_FALLBACK_SIZE = 128 * 1024
##
## enable CACHE_AS_RAM specifics
##
-default USE_DCACHE_RAM = 1
-default DCACHE_RAM_BASE = 0xc8000
-default DCACHE_RAM_SIZE = 0x08000
+default CONFIG_USE_DCACHE_RAM = 1
+default CONFIG_DCACHE_RAM_BASE = 0xc8000
+default CONFIG_DCACHE_RAM_SIZE = 0x08000
default CONFIG_USE_PRINTK_IN_CAR=1
##
## Use a small 8K stack
##
-default STACK_SIZE = 8 * 1024
+default CONFIG_STACK_SIZE = 8 * 1024
##
## Use a small 16K heap
##
-default HEAP_SIZE = 16 * 1024
+default CONFIG_HEAP_SIZE = 16 * 1024
##
## Only use the option table in a normal image
##
-#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
+#default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
##
## The default compiler
##
-default CROSS_COMPILE = ""
-default CC = "$(CROSS_COMPILE)gcc -m32"
-default HOSTCC = "gcc"
+default CONFIG_CROSS_COMPILE = ""
+default CC = "$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC = "gcc"
##
## The Serial Console
default CONFIG_CONSOLE_SERIAL8250 = 1
## Select the serial console baud rate
-default TTYS0_BAUD = 115200
-#default TTYS0_BAUD = 57600
-#default TTYS0_BAUD = 38400
-#default TTYS0_BAUD = 19200
-#default TTYS0_BAUD = 9600
-#default TTYS0_BAUD = 4800
-#default TTYS0_BAUD = 2400
-#default TTYS0_BAUD = 1200
+default CONFIG_TTYS0_BAUD = 115200
+#default CONFIG_TTYS0_BAUD = 57600
+#default CONFIG_TTYS0_BAUD = 38400
+#default CONFIG_TTYS0_BAUD = 19200
+#default CONFIG_TTYS0_BAUD = 9600
+#default CONFIG_TTYS0_BAUD = 4800
+#default CONFIG_TTYS0_BAUD = 2400
+#default CONFIG_TTYS0_BAUD = 1200
# Select the serial console base port
-default TTYS0_BASE = 0x3f8
+default CONFIG_TTYS0_BASE = 0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS = 0x3
+default CONFIG_TTYS0_LCS = 0x3
# Compile extra debugging code
-default DEBUG = 1
+default CONFIG_DEBUG = 1
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL = 8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL = 8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 8
#
# CBFS
0x1E2C, // disable ATXPowerGood - will cause a reboot!
0x0423, // don't delay POWerOK1/2
0x9072, // watchdog triggers POWOK, counts seconds
-#if !USE_WATCHDOG_ON_BOOT
+#if !CONFIG_USE_WATCHDOG_ON_BOOT
0x0073, 0x0074, // disable watchdog by setting timeout to 0
#endif
0xBF25, 0x372A, 0xF326, // select GPIO function for most pins
* Note: must do this AFTER the early_setup! It is counting on some
* early MSR setup for CS5536.
*/
- it8712f_enable_serial(0, TTYS0_BASE); // Does not use its 1st parameter
+ it8712f_enable_serial(0, CONFIG_TTYS0_BASE); // Does not use its 1st parameter
mb_gpio_init();
uart_init();
console_init();
const struct irq_routing_table intel_irq_routing_table = {
PIRQ_SIGNATURE, /* u32 signature */
PIRQ_VERSION, /* u16 version */
- 32 + 16 * IRQ_SLOT_COUNT,/* there can be total 7 devices on the bus */
+ 32 + 16 * CONFIG_IRQ_SLOT_COUNT,/* there can be total 7 devices on the bus */
0x00, /* Where the interrupt router lies (bus) */
(0x0F << 3) | 0x0, /* Where the interrupt router lies (dev) */
0x00, /* IRQs devoted exclusively to PCI usage */
{0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0}, /* u8 rfu[11] */
0xE0, /* u8 checksum, this has to set to some value that would give 0 after the sum of all bytes for this structure (including checksum) */
{
- /* If you change the number of entries, change the IRQ_SLOT_COUNT above! */
+ /* If you change the number of entries, change the CONFIG_IRQ_SLOT_COUNT above! */
/* bus, dev|fn, {link, bitmap}, {link, bitmap}, {link, bitmap}, {link, bitmap}, slot, rfu */
{0x00, (0x01 << 3) | 0x0, {{L_PIRQA, M_PIRQA}, {0x00, 0x00}, {0x00, 0x00}, {0x00, 0x00}}, 0x0, 0x0}, /* CPU */
{0x00, (0x0F << 3) | 0x0, {{L_PIRQA, M_PIRQA}, {L_PIRQB, M_PIRQB}, {L_PIRQC, M_PIRQC}, {L_PIRQD, M_PIRQD}}, 0x0, 0x0}, /* chipset */
## Based on Config.lb from AMD's DB800 and DBM690T mainboards.
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
##
driver mainboard.o
-if HAVE_PIRQ_TABLE
+if CONFIG_HAVE_PIRQ_TABLE
object irq_tables.o
end
# compile cache_as_ram.c to auto.inc
makerule ./cache_as_ram_auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
# mainboardinit ./failover.inc
end
## Based on Options.lb from AMD's DB800 mainboard.
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_ROM_PAYLOAD
uses CONFIG_IDE
uses CONFIG_FS_PAYLOAD
uses CONFIG_FS_EXT2
-uses AUTOBOOT_DELAY
-uses AUTOBOOT_CMDLINE
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_AUTOBOOT_DELAY
+uses CONFIG_AUTOBOOT_CMDLINE
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESS
uses CONFIG_COMPRESSED_PAYLOAD_NRV2B
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses HAVE_MP_TABLE
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses DEBUG
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_DEBUG
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
uses CONFIG_VIDEO_MB
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
uses CONFIG_USE_PRINTK_IN_CAR
-uses PIRQ_ROUTE
+uses CONFIG_PIRQ_ROUTE
-## ROM_SIZE is the size of boot ROM that this board will use.
-default ROM_SIZE = 512*1024
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
+default CONFIG_ROM_SIZE = 512*1024
###
### Build options
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT = 1
+default CONFIG_HAVE_FALLBACK_BOOT = 1
##
## no MP table
##
-default HAVE_MP_TABLE = 0
+default CONFIG_HAVE_MP_TABLE = 0
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET = 0
+default CONFIG_HAVE_HARD_RESET = 0
## Delay timer options
##
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE = 1
-default IRQ_SLOT_COUNT = 7
-default PIRQ_ROUTE = 1
+default CONFIG_HAVE_PIRQ_TABLE = 1
+default CONFIG_IRQ_SLOT_COUNT = 7
+default CONFIG_PIRQ_ROUTE = 1
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE = 0
+default CONFIG_HAVE_OPTION_TABLE = 0
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 64 * 1024
-default FALLBACK_SIZE = 128 * 1024
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 64 * 1024
+default CONFIG_FALLBACK_SIZE = 128 * 1024
##
## enable CACHE_AS_RAM specifics
##
-default USE_DCACHE_RAM = 1
-default DCACHE_RAM_BASE = 0xc8000
-default DCACHE_RAM_SIZE = 0x08000
+default CONFIG_USE_DCACHE_RAM = 1
+default CONFIG_DCACHE_RAM_BASE = 0xc8000
+default CONFIG_DCACHE_RAM_SIZE = 0x08000
default CONFIG_USE_PRINTK_IN_CAR=1
##
## Use a small 8K stack
##
-default STACK_SIZE = 0x2000
+default CONFIG_STACK_SIZE = 0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE = 0x4000
+default CONFIG_HEAP_SIZE = 0x4000
##
## Only use the option table in a normal image
##
-#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
+#default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
##
## The default compiler
##
-default CROSS_COMPILE = ""
-default CC = "$(CROSS_COMPILE)gcc -m32"
-default HOSTCC = "gcc"
+default CONFIG_CROSS_COMPILE = ""
+default CC = "$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC = "gcc"
##
## The Serial Console
default CONFIG_CONSOLE_SERIAL8250 = 1
## Select the serial console baud rate
-default TTYS0_BAUD = 115200
-#default TTYS0_BAUD = 57600
-#default TTYS0_BAUD = 38400
-#default TTYS0_BAUD = 19200
-#default TTYS0_BAUD = 9600
-#default TTYS0_BAUD = 4800
-#default TTYS0_BAUD = 2400
-#default TTYS0_BAUD = 1200
+default CONFIG_TTYS0_BAUD = 115200
+#default CONFIG_TTYS0_BAUD = 57600
+#default CONFIG_TTYS0_BAUD = 38400
+#default CONFIG_TTYS0_BAUD = 19200
+#default CONFIG_TTYS0_BAUD = 9600
+#default CONFIG_TTYS0_BAUD = 4800
+#default CONFIG_TTYS0_BAUD = 2400
+#default CONFIG_TTYS0_BAUD = 1200
# Select the serial console base port
-default TTYS0_BASE = 0x3f8
+default CONFIG_TTYS0_BASE = 0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS = 0x3
+default CONFIG_TTYS0_LCS = 0x3
# Compile extra debugging code
-default DEBUG = 1
+default CONFIG_DEBUG = 1
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL = 8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL = 8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 8
#
# CBFS
if (device != DIMM0)
return 0xFF; /* No DIMM1, don't even try. */
-#if DEBUG
+#if CONFIG_DEBUG
if (address >= sizeof(spdbytes) || spdbytes[address] == 0xFF) {
print_err("ERROR: spd_read_byte(DIMM0, 0x");
print_err_hex8(address);
0x1E2C, // disable ATXPowerGood
0x0423, // don't delay POWerOK1/2
0x9072, // watchdog triggers POWOK, counts seconds
-#if !USE_WATCHDOG_ON_BOOT
+#if !CONFIG_USE_WATCHDOG_ON_BOOT
0x0073, 0x0074, // disable watchdog by setting timeout to 0
#endif
0xBF25, 0x172A, 0xF326, // select GPIO function for most pins
* Note: Must do this AFTER the early_setup! It is counting on some
* early MSR setup for CS5536.
*/
- it8712f_enable_serial(0, TTYS0_BASE); // Does not use its 1st parameter
+ it8712f_enable_serial(0, CONFIG_TTYS0_BASE); // Does not use its 1st parameter
mb_gpio_init();
uart_init();
console_init();
const struct irq_routing_table intel_irq_routing_table = {
PIRQ_SIGNATURE, /* u32 signature */
PIRQ_VERSION, /* u16 version */
- 32 + 16 * IRQ_SLOT_COUNT,/* There can be total 7 devices on the bus */
+ 32 + 16 * CONFIG_IRQ_SLOT_COUNT,/* There can be total 7 devices on the bus */
0x00, /* Where the interrupt router lies (bus) */
(0x0F << 3) | 0x0, /* Where the interrupt router lies (dev) */
0x00, /* IRQs devoted exclusively to PCI usage */
{0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0}, /* u8 rfu[11] */
0xE0, /* u8 checksum, this has to set to some value that would give 0 after the sum of all bytes for this structure (including checksum) */
{
- /* If you change the number of entries, change the IRQ_SLOT_COUNT above! */
+ /* If you change the number of entries, change the CONFIG_IRQ_SLOT_COUNT above! */
/* bus, dev|fn, {link, bitmap}, {link, bitmap}, {link, bitmap}, {link, bitmap}, slot, rfu */
{0x00, (0x01 << 3) | 0x0, {{L_PIRQA, M_PIRQA}, {0x00, 0x00}, {0x00, 0x00}, {0x00, 0x00}}, 0x0, 0x0}, /* CPU */
{0x00, (0x0F << 3) | 0x0, {{L_PIRQA, M_PIRQA}, {L_PIRQB, M_PIRQB}, {L_PIRQC, M_PIRQC}, {L_PIRQD, M_PIRQD}}, 0x0, 0x0}, /* chipset */
object clock.o
##
-## Set our ARCH
+## Set our CONFIG_ARCH
##
arch ppc end
dir nvram
dir flash
-addaction coreboot.a "$(CROSS_COMPILE)ranlib coreboot.a"
+addaction coreboot.a "$(CONFIG_CROSS_COMPILE)ranlib coreboot.a"
makedefine CFLAGS += -g
uses CONFIG_SANDPOINT_UNITY
uses CONFIG_SANDPOINT_VALIS
uses CONFIG_SANDPOINT_GYRUS
-uses ISA_IO_BASE
-uses ISA_MEM_BASE
-uses PCIC0_CFGADDR
-uses PCIC0_CFGDATA
-uses PNP_CFGADDR
-uses PNP_CFGDATA
-uses _IO_BASE
-
-uses CROSS_COMPILE
-uses HAVE_OPTION_TABLE
+uses CONFIG_ISA_IO_BASE
+uses CONFIG_ISA_MEM_BASE
+uses CONFIG_PCIC0_CFGADDR
+uses CONFIG_PCIC0_CFGDATA
+uses CONFIG_PNP_CFGADDR
+uses CONFIG_PNP_CFGDATA
+uses CONFIG_IO_BASE
+
+uses CONFIG_CROSS_COMPILE
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_SANDPOINT_ALTIMUS
uses CONFIG_COMPRESS
-uses DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
uses CONFIG_USE_INIT
uses CONFIG_CHIP_CONFIGURE
-uses NO_POST
+uses CONFIG_NO_POST
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BASE
+uses CONFIG_TTYS0_BASE
uses CONFIG_IDE
uses CONFIG_FS_PAYLOAD
uses CONFIG_FS_EXT2
uses CONFIG_FS_ISO9660
uses CONFIG_FS_FAT
-uses AUTOBOOT_CMDLINE
-uses PAYLOAD_SIZE
-uses ROM_SIZE
-uses ROM_IMAGE_SIZE
-uses _RESET
-uses _EXCEPTION_VECTORS
-uses _ROMBASE
-uses _ROMSTART
-uses _RAMBASE
-uses _RAMSTART
-uses STACK_SIZE
-uses HEAP_SIZE
-
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_AUTOBOOT_CMDLINE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_RESET
+uses CONFIG_EXCEPTION_VECTORS
+uses CONFIG_ROMBASE
+uses CONFIG_ROMSTART
+uses CONFIG_RAMBASE
+uses CONFIG_RAMSTART
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses CROSS_COMPILE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
##
## Set memory map
##
-default ISA_IO_BASE=0xfe000000
-default ISA_MEM_BASE=0xfd000000
-default PCIC0_CFGADDR=0xfec00000
-default PCIC0_CFGDATA=0xfee00000
-default PNP_CFGADDR=0x15c
-default PNP_CFGDATA=0x15d
-default _IO_BASE=ISA_IO_BASE
+default CONFIG_ISA_IO_BASE=0xfe000000
+default CONFIG_ISA_MEM_BASE=0xfd000000
+default CONFIG_PCIC0_CFGADDR=0xfec00000
+default CONFIG_PCIC0_CFGDATA=0xfee00000
+default CONFIG_PNP_CFGADDR=0x15c
+default CONFIG_PNP_CFGDATA=0x15d
+default CONFIG_IO_BASE=CONFIG_ISA_IO_BASE
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc"
+default CONFIG_HOSTCC="gcc"
## use a cross compiler
-#default CROSS_COMPILE="powerpc-eabi-"
-#default CROSS_COMPILE="ppc_74xx-"
+#default CONFIG_CROSS_COMPILE="powerpc-eabi-"
+#default CONFIG_CROSS_COMPILE="ppc_74xx-"
default CONFIG_ARCH_X86=0
## Use stage 1 initialization code
default CONFIG_COMPRESS=0
## Turn off POST codes
-default NO_POST=1
+default CONFIG_NO_POST=1
## Enable serial console
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
default CONFIG_CONSOLE_SERIAL8250=1
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
## Load payload using filo
default CONFIG_IDE=1
default CONFIG_FS_EXT2=1
default CONFIG_FS_ISO9660=1
default CONFIG_FS_FAT=1
-default AUTOBOOT_CMDLINE="hdc1:/vmlinuz"
+default CONFIG_AUTOBOOT_CMDLINE="hdc1:/vmlinuz"
# coreboot must fit into 128KB
-default ROM_IMAGE_SIZE=131072
-default ROM_SIZE={ROM_IMAGE_SIZE+PAYLOAD_SIZE}
-default PAYLOAD_SIZE=262144
+default CONFIG_ROM_IMAGE_SIZE=131072
+default CONFIG_ROM_SIZE={CONFIG_ROM_IMAGE_SIZE+CONFIG_PAYLOAD_SIZE}
+default CONFIG_PAYLOAD_SIZE=262144
# Set stack and heap sizes (stage 2)
-default STACK_SIZE=0x10000
-default HEAP_SIZE=0x10000
+default CONFIG_STACK_SIZE=0x10000
+default CONFIG_HEAP_SIZE=0x10000
# Sandpoint Demo Board
## Base of ROM
-default _ROMBASE=0xfff00000
+default CONFIG_ROMBASE=0xfff00000
## Sandpoint reset vector
-default _RESET=_ROMBASE+0x100
+default CONFIG_RESET=CONFIG_ROMBASE+0x100
## Exception vectors (other than reset vector)
-default _EXCEPTION_VECTORS=_RESET+0x100
+default CONFIG_EXCEPTION_VECTORS=CONFIG_RESET+0x100
## Start of coreboot in the boot rom
-## = _RESET + exeception vector table size
-default _ROMSTART=_RESET+0x3100
+## = CONFIG_RESET + exeception vector table size
+default CONFIG_ROMSTART=CONFIG_RESET+0x3100
## Coreboot C code runs at this location in RAM
-default _RAMBASE=0x00100000
-default _RAMSTART=0x00100000
+default CONFIG_RAMBASE=0x00100000
+default CONFIG_RAMSTART=0x00100000
default CONFIG_SANDPOINT_ALTIMUS=1
void pnp_output(char address, char data)
{
- outb(address, PNP_CFGADDR);
- outb(data, PNP_CFGDATA);
+ outb(address, CONFIG_PNP_CFGADDR);
+ outb(data, CONFIG_PNP_CFGDATA);
}
void
*/
pnp_output(0x07, 6); /* LD 6 = UART0 */
pnp_output(0x30, 0); /* Dectivate */
- pnp_output(0x60, TTYS0_BASE >> 8); /* IO Base */
- pnp_output(0x61, TTYS0_BASE & 0xFF); /* IO Base */
+ pnp_output(0x60, CONFIG_TTYS0_BASE >> 8); /* IO Base */
+ pnp_output(0x61, CONFIG_TTYS0_BASE & 0xFF); /* IO Base */
pnp_output(0x30, 1); /* Activate */
- uart8250_init(TTYS0_BASE, 115200/TTYS0_BAUD, TTYS0_LCS);
+ uart8250_init(CONFIG_TTYS0_BASE, 115200/CONFIG_TTYS0_BAUD, CONFIG_TTYS0_LCS);
}
void
-uses ISA_IO_BASE
+uses CONFIG_ISA_IO_BASE
uses CONFIG_CBFS
-uses ISA_MEM_BASE
-uses PCIC0_CFGADDR
-uses PCIC0_CFGDATA
-uses PNP_CFGADDR
-uses PNP_CFGDATA
-uses _IO_BASE
-
-uses CROSS_COMPILE
-uses HAVE_OPTION_TABLE
+uses CONFIG_ISA_MEM_BASE
+uses CONFIG_PCIC0_CFGADDR
+uses CONFIG_PCIC0_CFGDATA
+uses CONFIG_PNP_CFGADDR
+uses CONFIG_PNP_CFGDATA
+uses CONFIG_IO_BASE
+
+uses CONFIG_CROSS_COMPILE
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_SANDPOINT_ALTIMUS
uses CONFIG_COMPRESS
-uses DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
uses CONFIG_USE_INIT
uses CONFIG_CHIP_CONFIGURE
-uses NO_POST
+uses CONFIG_NO_POST
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BASE
+uses CONFIG_TTYS0_BASE
uses CONFIG_IDE
uses CONFIG_FS_PAYLOAD
uses CONFIG_FS_EXT2
uses CONFIG_FS_FAT
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses AUTOBOOT_CMDLINE
-uses PAYLOAD_SIZE
-uses ROM_SIZE
-uses ROM_IMAGE_SIZE
-uses _RESET
-uses _EXCEPTION_VECTORS
-uses _ROMBASE
-uses _ROMSTART
-uses _RAMBASE
-uses _RAMSTART
-uses STACK_SIZE
-uses HEAP_SIZE
-
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_AUTOBOOT_CMDLINE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_RESET
+uses CONFIG_EXCEPTION_VECTORS
+uses CONFIG_ROMBASE
+uses CONFIG_ROMSTART
+uses CONFIG_RAMBASE
+uses CONFIG_RAMSTART
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses CROSS_COMPILE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
##
## Set memory map
##
-default ISA_IO_BASE=0xfe000000
-default ISA_MEM_BASE=0xfd000000
-default PCIC0_CFGADDR=0xfec00000
-default PCIC0_CFGDATA=0xfee00000
-default PNP_CFGADDR=0x15c
-default PNP_CFGDATA=0x15d
-default _IO_BASE=ISA_IO_BASE
+default CONFIG_ISA_IO_BASE=0xfe000000
+default CONFIG_ISA_MEM_BASE=0xfd000000
+default CONFIG_PCIC0_CFGADDR=0xfec00000
+default CONFIG_PCIC0_CFGDATA=0xfee00000
+default CONFIG_PNP_CFGADDR=0x15c
+default CONFIG_PNP_CFGDATA=0x15d
+default CONFIG_IO_BASE=CONFIG_ISA_IO_BASE
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc"
+default CONFIG_HOSTCC="gcc"
## use a cross compiler
-#default CROSS_COMPILE="powerpc-eabi-"
-#default CROSS_COMPILE="ppc_74xx-"
+#default CONFIG_CROSS_COMPILE="powerpc-eabi-"
+#default CONFIG_CROSS_COMPILE="ppc_74xx-"
## Use stage 1 initialization code
default CONFIG_USE_INIT=1
default CONFIG_COMPRESS=0
## Turn off POST codes
-default NO_POST=1
+default CONFIG_NO_POST=1
## Enable serial console
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
default CONFIG_CONSOLE_SERIAL8250=1
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
## Load payload using filo
default CONFIG_IDE=1
default CONFIG_FS_EXT2=1
default CONFIG_FS_ISO9660=1
default CONFIG_FS_FAT=1
-default AUTOBOOT_CMDLINE="hdc1:/vmlinuz"
+default CONFIG_AUTOBOOT_CMDLINE="hdc1:/vmlinuz"
# coreboot must fit into 128KB
-default ROM_IMAGE_SIZE=131072
-default ROM_SIZE={ROM_IMAGE_SIZE+PAYLOAD_SIZE}
-default PAYLOAD_SIZE=262144
+default CONFIG_ROM_IMAGE_SIZE=131072
+default CONFIG_ROM_SIZE={CONFIG_ROM_IMAGE_SIZE+CONFIG_PAYLOAD_SIZE}
+default CONFIG_PAYLOAD_SIZE=262144
# Set stack and heap sizes (stage 2)
-default STACK_SIZE=0x10000
-default HEAP_SIZE=0x10000
+default CONFIG_STACK_SIZE=0x10000
+default CONFIG_HEAP_SIZE=0x10000
# Sandpoint Demo Board
## Base of ROM
-default _ROMBASE=0xfff00000
+default CONFIG_ROMBASE=0xfff00000
## Sandpoint reset vector
-default _RESET=_ROMBASE+0x100
+default CONFIG_RESET=CONFIG_ROMBASE+0x100
## Exception vectors (other than reset vector)
-default _EXCEPTION_VECTORS=_RESET+0x100
+default CONFIG_EXCEPTION_VECTORS=CONFIG_RESET+0x100
## Start of coreboot in the boot rom
-## = _RESET + exeception vector table size
-default _ROMSTART=_RESET+0x3100
+## = CONFIG_RESET + exeception vector table size
+default CONFIG_ROMSTART=CONFIG_RESET+0x3100
## Coreboot C code runs at this location in RAM
-default _RAMBASE=0x00100000
-default _RAMSTART=0x00100000
+default CONFIG_RAMBASE=0x00100000
+default CONFIG_RAMSTART=0x00100000
### End Options.lb
#
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
arch i386 end
driver mainboard.o
-if HAVE_PIRQ_TABLE
+if CONFIG_HAVE_PIRQ_TABLE
object irq_tables.o
end
makerule ./failover.E
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -E -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -E -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./auto.E
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -E -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -E -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
mainboardinit cpu/x86/16bit/entry16.inc
mainboardinit cpu/x86/32bit/entry32.inc
ldscript /cpu/x86/16bit/entry16.lds
ldscript /cpu/x86/32bit/entry32.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
mainboardinit arch/i386/lib/cpu_reset.inc
mainboardinit arch/i386/lib/id.inc
ldscript /arch/i386/lib/id.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_ROM_PAYLOAD
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses HAVE_MP_TABLE
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
-default ROM_SIZE = 256 * 1024
-default HAVE_FALLBACK_BOOT = 1
-default HAVE_MP_TABLE = 0
-default HAVE_HARD_RESET = 0
+default CONFIG_ROM_SIZE = 256 * 1024
+default CONFIG_HAVE_FALLBACK_BOOT = 1
+default CONFIG_HAVE_MP_TABLE = 0
+default CONFIG_HAVE_HARD_RESET = 0
default CONFIG_UDELAY_TSC = 1
default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 1
-default HAVE_PIRQ_TABLE = 1
-default IRQ_SLOT_COUNT = 0 # Override this in targets/*/Config.lb.
-default MAINBOARD_VENDOR = "N/A" # Override this in targets/*/Config.lb.
-default MAINBOARD_PART_NUMBER = "N/A" # Override this in targets/*/Config.lb.
-default ROM_IMAGE_SIZE = 64 * 1024
-default FALLBACK_SIZE = 128 * 1024
-default STACK_SIZE = 8 * 1024
-default HEAP_SIZE = 16 * 1024
-default HAVE_OPTION_TABLE = 0
-#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_HAVE_PIRQ_TABLE = 1
+default CONFIG_IRQ_SLOT_COUNT = 0 # Override this in targets/*/Config.lb.
+default CONFIG_MAINBOARD_VENDOR = "N/A" # Override this in targets/*/Config.lb.
+default CONFIG_MAINBOARD_PART_NUMBER = "N/A" # Override this in targets/*/Config.lb.
+default CONFIG_ROM_IMAGE_SIZE = 64 * 1024
+default CONFIG_FALLBACK_SIZE = 128 * 1024
+default CONFIG_STACK_SIZE = 8 * 1024
+default CONFIG_HEAP_SIZE = 16 * 1024
+default CONFIG_HAVE_OPTION_TABLE = 0
+#default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 0
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
-default CROSS_COMPILE = ""
-default CC = "$(CROSS_COMPILE)gcc -m32"
-default HOSTCC = "gcc"
+default CONFIG_CROSS_COMPILE = ""
+default CC = "$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC = "gcc"
default CONFIG_CONSOLE_SERIAL8250 = 1
-default TTYS0_BAUD = 115200
-default TTYS0_BASE = 0x3f8
-default TTYS0_LCS = 0x3 # 8n1
-default DEFAULT_CONSOLE_LOGLEVEL = 9
-default MAXIMUM_CONSOLE_LOGLEVEL = 9
+default CONFIG_TTYS0_BAUD = 115200
+default CONFIG_TTYS0_BASE = 0x3f8
+default CONFIG_TTYS0_LCS = 0x3 # 8n1
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
default CONFIG_CONSOLE_VGA = 1
default CONFIG_PCI_ROM_RUN = 1
if (bist == 0)
early_mtrr_init();
- w83977tf_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ w83977tf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
report_bist_failure(bist);
const struct irq_routing_table intel_irq_routing_table = {
PIRQ_SIGNATURE,
PIRQ_VERSION,
- 32 + 16 * IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
+ 32 + 16 * CONFIG_IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
0x00, /* Interrupt router bus */
(0x07 << 3) | 0x0, /* Interrupt router device */
0x800, /* IRQs devoted exclusively to PCI usage */
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
arch i386 end
driver mainboard.o
-if HAVE_PIRQ_TABLE
+if CONFIG_HAVE_PIRQ_TABLE
object irq_tables.o
end
makerule ./failover.E
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -E -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -E -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./auto.E
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -E -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -E -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
ldscript /cpu/x86/32bit/entry32.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
mainboardinit arch/i386/lib/id.inc
ldscript /arch/i386/lib/id.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_ROM_PAYLOAD
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses HAVE_MP_TABLE
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
-default ROM_SIZE = 256 * 1024
-default HAVE_FALLBACK_BOOT = 1
-default HAVE_MP_TABLE = 0
-default HAVE_HARD_RESET = 0
+default CONFIG_ROM_SIZE = 256 * 1024
+default CONFIG_HAVE_FALLBACK_BOOT = 1
+default CONFIG_HAVE_MP_TABLE = 0
+default CONFIG_HAVE_HARD_RESET = 0
default CONFIG_UDELAY_TSC = 1
default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 1
-default HAVE_PIRQ_TABLE = 1
-default IRQ_SLOT_COUNT = 0 # Override this in targets/*/Config.lb.
-default MAINBOARD_VENDOR = "N/A" # Override this in targets/*/Config.lb.
-default MAINBOARD_PART_NUMBER = "N/A" # Override this in targets/*/Config.lb.
-default ROM_IMAGE_SIZE = 64 * 1024
-default FALLBACK_SIZE = 128 * 1024
-default STACK_SIZE = 8 * 1024
-default HEAP_SIZE = 16 * 1024
-default HAVE_OPTION_TABLE = 0
-#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_HAVE_PIRQ_TABLE = 1
+default CONFIG_IRQ_SLOT_COUNT = 0 # Override this in targets/*/Config.lb.
+default CONFIG_MAINBOARD_VENDOR = "N/A" # Override this in targets/*/Config.lb.
+default CONFIG_MAINBOARD_PART_NUMBER = "N/A" # Override this in targets/*/Config.lb.
+default CONFIG_ROM_IMAGE_SIZE = 64 * 1024
+default CONFIG_FALLBACK_SIZE = 128 * 1024
+default CONFIG_STACK_SIZE = 8 * 1024
+default CONFIG_HEAP_SIZE = 16 * 1024
+default CONFIG_HAVE_OPTION_TABLE = 0
+#default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 0
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
-default CROSS_COMPILE = ""
-default CC = "$(CROSS_COMPILE)gcc -m32"
-default HOSTCC = "gcc"
+default CONFIG_CROSS_COMPILE = ""
+default CC = "$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC = "gcc"
default CONFIG_CONSOLE_SERIAL8250 = 1
-default TTYS0_BAUD = 115200
-default TTYS0_BASE = 0x3f8
-default TTYS0_LCS = 0x3 # 8n1
-default DEFAULT_CONSOLE_LOGLEVEL = 9
-default MAXIMUM_CONSOLE_LOGLEVEL = 9
+default CONFIG_TTYS0_BAUD = 115200
+default CONFIG_TTYS0_BASE = 0x3f8
+default CONFIG_TTYS0_LCS = 0x3 # 8n1
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
default CONFIG_CONSOLE_VGA = 1
default CONFIG_PCI_ROM_RUN = 1
if (bist == 0)
early_mtrr_init();
- w83977tf_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ w83977tf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
report_bist_failure(bist);
const struct irq_routing_table intel_irq_routing_table = {
PIRQ_SIGNATURE,
PIRQ_VERSION,
- 32 + 16 * IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
+ 32 + 16 * CONFIG_IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
0x00, /* Interrupt router bus */
(0x07 << 3) | 0x0, /* Interrupt router device */
0x1c00, /* IRQs devoted exclusively to PCI usage */
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
arch i386 end
driver mainboard.o
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
# object reset.o
makerule ./failover.E
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./auto.E
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -E -mcpu=p2 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -E -mcpu=p2 -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -mcpu=p2 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -mcpu=p2 -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
mainboardinit cpu/x86/16bit/entry16.inc
mainboardinit cpu/x86/32bit/entry32.inc
ldscript /cpu/x86/16bit/entry16.lds
ldscript /cpu/x86/32bit/entry32.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
mainboardinit arch/i386/lib/cpu_reset.inc
mainboardinit arch/i386/lib/id.inc
ldscript /arch/i386/lib/id.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_ROM_PAYLOAD
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses HAVE_MP_TABLE
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
-uses HAVE_HIGH_TABLES
+uses CONFIG_HAVE_HIGH_TABLES
-default ROM_SIZE = 512 * 1024
-default HAVE_FALLBACK_BOOT = 1
-default HAVE_MP_TABLE = 0
-default HAVE_HARD_RESET = 0
-default HAVE_PIRQ_TABLE = 1
-default IRQ_SLOT_COUNT = 0 # Override this in targets/*/Config.lb.
-default MAINBOARD_VENDOR = "N/A" # Override this in targets/*/Config.lb.
-default MAINBOARD_PART_NUMBER = "N/A" # Override this in targets/*/Config.lb.
-default ROM_IMAGE_SIZE = 64 * 1024
-default FALLBACK_SIZE = ROM_IMAGE_SIZE
-default STACK_SIZE = 8 * 1024
-default HEAP_SIZE = 16 * 1024
-default HAVE_OPTION_TABLE = 0
-#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_ROM_SIZE = 512 * 1024
+default CONFIG_HAVE_FALLBACK_BOOT = 1
+default CONFIG_HAVE_MP_TABLE = 0
+default CONFIG_HAVE_HARD_RESET = 0
+default CONFIG_HAVE_PIRQ_TABLE = 1
+default CONFIG_IRQ_SLOT_COUNT = 0 # Override this in targets/*/Config.lb.
+default CONFIG_MAINBOARD_VENDOR = "N/A" # Override this in targets/*/Config.lb.
+default CONFIG_MAINBOARD_PART_NUMBER = "N/A" # Override this in targets/*/Config.lb.
+default CONFIG_ROM_IMAGE_SIZE = 64 * 1024
+default CONFIG_FALLBACK_SIZE = CONFIG_ROM_IMAGE_SIZE
+default CONFIG_STACK_SIZE = 8 * 1024
+default CONFIG_HEAP_SIZE = 16 * 1024
+default CONFIG_HAVE_OPTION_TABLE = 0
+#default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 0
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
-default CROSS_COMPILE = ""
-default CC = "$(CROSS_COMPILE)gcc -m32"
-default HOSTCC = "gcc"
+default CONFIG_CROSS_COMPILE = ""
+default CC = "$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC = "gcc"
default CONFIG_CONSOLE_SERIAL8250 = 1
-default TTYS0_BAUD = 115200
-default TTYS0_BASE = 0x3f8
-default TTYS0_LCS = 0x3 # 8n1
-default DEFAULT_CONSOLE_LOGLEVEL = 9
-default MAXIMUM_CONSOLE_LOGLEVEL = 9
+default CONFIG_TTYS0_BAUD = 115200
+default CONFIG_TTYS0_BASE = 0x3f8
+default CONFIG_TTYS0_LCS = 0x3 # 8n1
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
default CONFIG_UDELAY_TSC = 1
default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 1
default CONFIG_CONSOLE_VGA = 1
default CONFIG_PCI_ROM_RUN = 1
default CONFIG_CBFS = 1
-default HAVE_HIGH_TABLES = 1
+default CONFIG_HAVE_HIGH_TABLES = 1
end
outb(0x87, 0x2e);
outb(0x87, 0x2e);
pnp_write_config(SERIAL_DEV, 0x24, 0x84 | (1 << 6));
- w83627hf_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ w83627hf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
outb(0x87, 0xaa);
uart_init();
const struct irq_routing_table intel_irq_routing_table = {
PIRQ_SIGNATURE,
PIRQ_VERSION,
- 32 + 16 * IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
+ 32 + 16 * CONFIG_IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
0x00, /* Interrupt router bus */
(0x1f << 3) | 0x0, /* Interrupt router device */
0x1c00, /* IRQs devoted exclusively to PCI usage */
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/failovercalculation.lb
arch i386 end
# Needed by irq_tables and mptable and acpi_tables.
object get_bus_conf.o
-if HAVE_MP_TABLE
+if CONFIG_HAVE_MP_TABLE
object mptable.o
end
-if HAVE_PIRQ_TABLE
+if CONFIG_HAVE_PIRQ_TABLE
object irq_tables.o
end
if CONFIG_USE_INIT
makerule ./auto.o
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
end
else
makerule ./auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
##
## Build our 16 bit and 32 bit coreboot entry code.
##
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
end
##
## Build our reset vector (this is where coreboot is entered).
##
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
ldscript /cpu/x86/32bit/reset32.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
##
## ROMSTRAP table for CK804
##
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
mainboardinit southbridge/nvidia/ck804/romstrap.inc
ldscript /southbridge/nvidia/ck804/romstrap.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
mainboardinit southbridge/nvidia/ck804/romstrap.inc
ldscript /southbridge/nvidia/ck804/romstrap.lds
end
### Things are delicate and we test to see if we should
### failover to another image.
###
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
ldscript /arch/i386/lib/failover_failover.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
end
end
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses USE_FAILOVER_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_FAILOVER_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_USE_FAILOVER_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_FAILOVER_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_MAX_CPUS
uses CONFIG_MAX_PHYSICAL_CPUS
uses CONFIG_LOGICAL_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses FAILOVER_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_FAILOVER_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
-uses _RAMBASE
+uses CONFIG_RAMBASE
uses CONFIG_GDB_STUB
-uses CROSS_COMPILE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_SERIAL8250
uses CONFIG_CONSOLE_BTEXT
-uses HAVE_INIT_TIMER
+uses CONFIG_HAVE_INIT_TIMER
uses CONFIG_GDB_STUB
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
-uses HW_MEM_HOLE_SIZEK
+uses CONFIG_HW_MEM_HOLE_SIZEK
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
uses CONFIG_USE_INIT
-uses DCACHE_RAM_GLOBAL_VAR_SIZE
+uses CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE
uses CONFIG_AP_CODE_IN_CAR
uses CONFIG_USE_PRINTK_IN_CAR
-uses MEM_TRAIN_SEQ
-uses WAIT_BEFORE_CPUS_INIT
+uses CONFIG_MEM_TRAIN_SEQ
+uses CONFIG_WAIT_BEFORE_CPUS_INIT
-uses ENABLE_APIC_EXT_ID
-uses APIC_ID_OFFSET
-uses LIFT_BSP_APIC_ID
+uses CONFIG_ENABLE_APIC_EXT_ID
+uses CONFIG_APIC_ID_OFFSET
+uses CONFIG_LIFT_BSP_APIC_ID
uses CONFIG_PCI_64BIT_PREF_MEM
-uses HT_CHAIN_UNITID_BASE
-uses HT_CHAIN_END_UNITID_BASE
-uses SB_HT_CHAIN_ON_BUS0
-uses SB_HT_CHAIN_UNITID_OFFSET_ONLY
+uses CONFIG_HT_CHAIN_UNITID_BASE
+uses CONFIG_HT_CHAIN_END_UNITID_BASE
+uses CONFIG_SB_HT_CHAIN_ON_BUS0
+uses CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY
uses CONFIG_LB_MEM_TOPK
-## ROM_SIZE is the size of boot ROM that this board will use.
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
## ---> 512 Kbytes
-default ROM_SIZE=(512*1024)
+default CONFIG_ROM_SIZE=(512*1024)
##
-## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
+## CONFIG_FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
##
-default FALLBACK_SIZE=(252*1024)
+default CONFIG_FALLBACK_SIZE=(252*1024)
#FAILOVER: 4K
-default FAILOVER_SIZE=(4*1024)
+default CONFIG_FAILOVER_SIZE=(4*1024)
###
### Build options
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
-default HAVE_FAILOVER_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FAILOVER_BOOT=1
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=13
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=13
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
##
## Move the default coreboot cmos range off of AMD RTC registers
##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
+default CONFIG_LB_CKS_RANGE_START=49
+default CONFIG_LB_CKS_RANGE_END=122
+default CONFIG_LB_CKS_LOC=123
##
## Build code for SMP support
default CONFIG_LOGICAL_CPUS=1
#1G memory hole
-default HW_MEM_HOLE_SIZEK=0x100000
+default CONFIG_HW_MEM_HOLE_SIZEK=0x100000
##HT Unit ID offset, default is 1, the typical one
-default HT_CHAIN_UNITID_BASE=0
+default CONFIG_HT_CHAIN_UNITID_BASE=0
##real SB Unit ID, default is 0x20, mean dont touch it at last
-#default HT_CHAIN_END_UNITID_BASE=0x10
+#default CONFIG_HT_CHAIN_END_UNITID_BASE=0x10
#make the SB HT chain on bus 0, default is not (0)
-default SB_HT_CHAIN_ON_BUS0=2
+default CONFIG_SB_HT_CHAIN_ON_BUS0=2
##only offset for SB chain?, default is yes(1)
-default SB_HT_CHAIN_UNITID_OFFSET_ONLY=0
+default CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY=0
#BTEXT Console
#default CONFIG_CONSOLE_BTEXT=1
##
## enable CACHE_AS_RAM specifics
##
-default USE_DCACHE_RAM=1
-#default DCACHE_RAM_BASE=0xcf000
-#default DCACHE_RAM_SIZE=0x1000
-default DCACHE_RAM_BASE=0xc8000
-default DCACHE_RAM_SIZE=0x08000
-default DCACHE_RAM_GLOBAL_VAR_SIZE=0x01000
+default CONFIG_USE_DCACHE_RAM=1
+#default CONFIG_DCACHE_RAM_BASE=0xcf000
+#default CONFIG_DCACHE_RAM_SIZE=0x1000
+default CONFIG_DCACHE_RAM_BASE=0xc8000
+default CONFIG_DCACHE_RAM_SIZE=0x08000
+default CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE=0x01000
default CONFIG_USE_INIT=0
default CONFIG_AP_CODE_IN_CAR=0
-default MEM_TRAIN_SEQ=2
-default WAIT_BEFORE_CPUS_INIT=0
+default CONFIG_MEM_TRAIN_SEQ=2
+default CONFIG_WAIT_BEFORE_CPUS_INIT=0
## APIC stuff
-#default ENABLE_APIC_EXT_ID=0
-#default APIC_ID_OFFSET=0x10
-#default LIFT_BSP_APIC_ID=0
+#default CONFIG_ENABLE_APIC_EXT_ID=0
+#default CONFIG_APIC_ID_OFFSET=0x10
+#default CONFIG_LIFT_BSP_APIC_ID=0
#default CONFIG_PCI_64BIT_PREF_MEM=1
##
## Clean up the motherboard id strings
##
-default MAINBOARD_PART_NUMBER="K8N Neo3 (MS-7135)"
-default MAINBOARD_VENDOR="MSI"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x1462
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x7135
+default CONFIG_MAINBOARD_PART_NUMBER="K8N Neo3 (MS-7135)"
+default CONFIG_MAINBOARD_VENDOR="MSI"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x1462
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x7135
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = (64*1024)
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = (64*1024)
#65536
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE=0x4000
+default CONFIG_HEAP_SIZE=0x4000
##
## Only use the option table in a normal image
##
-#efault USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = (!USE_FALLBACK_IMAGE) && (!USE_FAILOVER_IMAGE )
+#efault CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = (!CONFIG_USE_FALLBACK_IMAGE) && (!CONFIG_USE_FAILOVER_IMAGE )
##
## coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00004000
+default CONFIG_RAMBASE=0x00004000
##
## Load the payload from the ROM
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## Disable the gdb stub by default
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
### End Options.lb
#
#include "northbridge/amd/amdk8/reset_test.c"
#include "superio/winbond/w83627hf/w83627hf_early_serial.c"
-#if USE_FAILOVER_IMAGE == 0
+#if CONFIG_USE_FAILOVER_IMAGE == 0
/* Used by ck804_early_setup(). */
#define CK804_NUM 1
#include "cpu/amd/car/post_cache_as_ram.c"
#include "cpu/amd/model_fxx/init_cpus.c"
-#endif /* USE_FAILOVER_IMAGE */
+#endif /* CONFIG_USE_FAILOVER_IMAGE */
-#if ((HAVE_FAILOVER_BOOT==1) && (USE_FAILOVER_IMAGE == 1)) \
- || ((HAVE_FAILOVER_BOOT==0) && (USE_FALLBACK_IMAGE == 1))
+#if ((CONFIG_HAVE_FAILOVER_BOOT==1) && (CONFIG_USE_FAILOVER_IMAGE == 1)) \
+ || ((CONFIG_HAVE_FAILOVER_BOOT==0) && (CONFIG_USE_FALLBACK_IMAGE == 1))
#include "southbridge/nvidia/ck804/ck804_enable_rom.c"
#include "northbridge/amd/amdk8/early_ht.c"
fallback_image:
-#if HAVE_FAILOVER_BOOT == 1
+#if CONFIG_HAVE_FAILOVER_BOOT == 1
__asm__ volatile ("jmp __fallback_image"
: /* outputs */
:"a" (bist), "b"(cpu_init_detectedx) /* inputs */
;
}
-#endif /* ((HAVE_FAILOVER_BOOT==1) && (USE_FAILOVER_IMAGE == 1)) ... */
+#endif /* ((CONFIG_HAVE_FAILOVER_BOOT==1) && (CONFIG_USE_FAILOVER_IMAGE == 1)) ... */
void real_main(unsigned long bist, unsigned long cpu_init_detectedx);
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
-#if HAVE_FAILOVER_BOOT == 1
-#if USE_FAILOVER_IMAGE == 1
+#if CONFIG_HAVE_FAILOVER_BOOT == 1
+#if CONFIG_USE_FAILOVER_IMAGE == 1
failover_process(bist, cpu_init_detectedx);
#else
real_main(bist, cpu_init_detectedx);
#endif
#else
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
failover_process(bist, cpu_init_detectedx);
#endif
real_main(bist, cpu_init_detectedx);
#endif
}
-#if USE_FAILOVER_IMAGE == 0
+#if CONFIG_USE_FAILOVER_IMAGE == 0
void real_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
static const uint16_t spd_addr[] = {
bsp_apicid = init_cpus(cpu_init_detectedx);
}
- w83627hf_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ w83627hf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
post_cache_as_ram();
}
-#endif /* USE_FAILOVER_IMAGE */
+#endif /* CONFIG_USE_FAILOVER_IMAGE */
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/failovercalculation.lb
arch i386 end
driver mainboard.o
object get_bus_conf.o # Needed by irq_tables and mptable (and acpi_tables).
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
# object reset.o
if CONFIG_USE_INIT
makerule ./cache_as_ram_auto.o
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
end
else
makerule ./cache_as_ram_auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
end
-if USE_FAILOVER_IMAGE
+if CONFIG_USE_FAILOVER_IMAGE
else
if CONFIG_AP_CODE_IN_CAR
makerule ./apc_auto.o
- depends "$(MAINBOARD)/apc_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/apc_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/apc_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/apc_auto.c -o $@"
end
ldscript /arch/i386/init/ldscript_apc.lb
end
end
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
end
ldscript /cpu/amd/car/cache_as_ram.lds
end
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
ldscript /cpu/x86/32bit/reset32.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
ldscript /southbridge/nvidia/mcp55/id.lds
# ROMSTRAP table for MCP55.
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
mainboardinit southbridge/nvidia/mcp55/romstrap.inc
ldscript /southbridge/nvidia/mcp55/romstrap.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
mainboardinit southbridge/nvidia/mcp55/romstrap.inc
ldscript /southbridge/nvidia/mcp55/romstrap.lds
end
mainboardinit cpu/amd/car/cache_as_ram.inc
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
ldscript /arch/i386/lib/failover_failover.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
end
end
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses USE_FAILOVER_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_FAILOVER_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_USE_FAILOVER_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_FAILOVER_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_MAX_CPUS
uses CONFIG_MAX_PHYSICAL_CPUS
uses CONFIG_LOGICAL_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses FAILOVER_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_FAILOVER_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_NRV2B
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
-uses _RAMBASE
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_RAMBASE
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_SERIAL8250
-uses HAVE_INIT_TIMER # ?
-uses CROSS_COMPILE
+uses CONFIG_HAVE_INIT_TIMER # ?
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
uses CONFIG_USBDEBUG_DIRECT
-uses HW_MEM_HOLE_SIZEK
-uses HW_MEM_HOLE_SIZE_AUTO_INC
-uses K8_HT_FREQ_1G_SUPPORT
-uses HT_CHAIN_UNITID_BASE
-uses HT_CHAIN_END_UNITID_BASE
-uses SB_HT_CHAIN_ON_BUS0
-uses SB_HT_CHAIN_UNITID_OFFSET_ONLY
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
-uses DCACHE_RAM_GLOBAL_VAR_SIZE
+uses CONFIG_HW_MEM_HOLE_SIZEK
+uses CONFIG_HW_MEM_HOLE_SIZE_AUTO_INC
+uses CONFIG_K8_HT_FREQ_1G_SUPPORT
+uses CONFIG_HT_CHAIN_UNITID_BASE
+uses CONFIG_HT_CHAIN_END_UNITID_BASE
+uses CONFIG_SB_HT_CHAIN_ON_BUS0
+uses CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
+uses CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE
uses CONFIG_USE_INIT
-uses SERIAL_CPU_INIT
-uses ENABLE_APIC_EXT_ID
-uses APIC_ID_OFFSET
-uses LIFT_BSP_APIC_ID
+uses CONFIG_SERIAL_CPU_INIT
+uses CONFIG_ENABLE_APIC_EXT_ID
+uses CONFIG_APIC_ID_OFFSET
+uses CONFIG_LIFT_BSP_APIC_ID
uses CONFIG_PCI_64BIT_PREF_MEM
uses CONFIG_LB_MEM_TOPK
uses CONFIG_AP_CODE_IN_CAR
-uses MEM_TRAIN_SEQ
-uses WAIT_BEFORE_CPUS_INIT
+uses CONFIG_MEM_TRAIN_SEQ
+uses CONFIG_WAIT_BEFORE_CPUS_INIT
uses CONFIG_USE_PRINTK_IN_CAR
-default ROM_SIZE = 512 * 1024
-default FALLBACK_SIZE = (256 * 1024) - (4 * 1024)
-default FAILOVER_SIZE = 4 * 1024
+default CONFIG_ROM_SIZE = 512 * 1024
+default CONFIG_FALLBACK_SIZE = (256 * 1024) - (4 * 1024)
+default CONFIG_FAILOVER_SIZE = 4 * 1024
default CONFIG_LB_MEM_TOPK = 2048 # 1MB more for pgtbl.
-default HAVE_FALLBACK_BOOT = 1
-default HAVE_FAILOVER_BOOT = 1
-default HAVE_HARD_RESET = 1
-default HAVE_PIRQ_TABLE = 1
-default IRQ_SLOT_COUNT = 11 # TODO: Check if correct.
-default HAVE_MP_TABLE = 1 # TODO: Check if correct.
-default HAVE_OPTION_TABLE = 1
+default CONFIG_HAVE_FALLBACK_BOOT = 1
+default CONFIG_HAVE_FAILOVER_BOOT = 1
+default CONFIG_HAVE_HARD_RESET = 1
+default CONFIG_HAVE_PIRQ_TABLE = 1
+default CONFIG_IRQ_SLOT_COUNT = 11 # TODO: Check if correct.
+default CONFIG_HAVE_MP_TABLE = 1 # TODO: Check if correct.
+default CONFIG_HAVE_OPTION_TABLE = 1
default CONFIG_SMP = 1
default CONFIG_MAX_CPUS = 2
default CONFIG_MAX_PHYSICAL_CPUS = 1
default CONFIG_LOGICAL_CPUS = 1
-# default SERIAL_CPU_INIT = 0
-default ENABLE_APIC_EXT_ID = 0
-default APIC_ID_OFFSET = 0x10
-default LIFT_BSP_APIC_ID = 1
+# default CONFIG_SERIAL_CPU_INIT = 0
+default CONFIG_ENABLE_APIC_EXT_ID = 0
+default CONFIG_APIC_ID_OFFSET = 0x10
+default CONFIG_LIFT_BSP_APIC_ID = 1
# Move the default coreboot CMOS range off of AMD RTC registers.
-default LB_CKS_RANGE_START = 49
-default LB_CKS_RANGE_END = 122
-default LB_CKS_LOC = 123
+default CONFIG_LB_CKS_RANGE_START = 49
+default CONFIG_LB_CKS_RANGE_END = 122
+default CONFIG_LB_CKS_LOC = 123
# Memory hole size. 0 means disable, others will enable the hole. In that
# case, if it is smaller than mmio_basek, it will use mmio_basek instead.
-# default HW_MEM_HOLE_SIZEK = 0x200000 # 2GB
-default HW_MEM_HOLE_SIZEK = 0x100000 # 1GB
-# default HW_MEM_HOLE_SIZEK = 0x80000 # 512MB
+# default CONFIG_HW_MEM_HOLE_SIZEK = 0x200000 # 2GB
+default CONFIG_HW_MEM_HOLE_SIZEK = 0x100000 # 1GB
+# default CONFIG_HW_MEM_HOLE_SIZEK = 0x80000 # 512MB
# Make auto increase hole size to avoid hole_startk equal to basek so as
# to make some kernel happy.
-# default HW_MEM_HOLE_SIZE_AUTO_INC = 1
+# default CONFIG_HW_MEM_HOLE_SIZE_AUTO_INC = 1
# Opteron K8 1G HT support.
-default K8_HT_FREQ_1G_SUPPORT = 1
+default CONFIG_K8_HT_FREQ_1G_SUPPORT = 1
# HT Unit ID offset, default is 1, the typical one, 0 means only one HT device.
-default HT_CHAIN_UNITID_BASE = 0
+default CONFIG_HT_CHAIN_UNITID_BASE = 0
# Real SB Unit ID, default is 0x20, mean don't touch it at last.
-# default HT_CHAIN_END_UNITID_BASE = 0x6
+# default CONFIG_HT_CHAIN_END_UNITID_BASE = 0x6
# Make the SB HT chain on bus 0, default is not (0).
-default SB_HT_CHAIN_ON_BUS0 = 2
+default CONFIG_SB_HT_CHAIN_ON_BUS0 = 2
# Only offset for SB chain? Default is yes (1).
-default SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0
+default CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0
# Allow capable device use that above 4GB.
# default CONFIG_PCI_64BIT_PREF_MEM = 1
default CONFIG_CONSOLE_VGA = 1 # Needed for VGA.
default CONFIG_PCI_ROM_RUN = 1 # Needed for VGA.
default CONFIG_USBDEBUG_DIRECT = 0
-default USE_DCACHE_RAM = 1
-default DCACHE_RAM_BASE = 0xc8000
-default DCACHE_RAM_SIZE = 0x08000
-default DCACHE_RAM_GLOBAL_VAR_SIZE = 0x01000
+default CONFIG_USE_DCACHE_RAM = 1
+default CONFIG_DCACHE_RAM_BASE = 0xc8000
+default CONFIG_DCACHE_RAM_SIZE = 0x08000
+default CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE = 0x01000
default CONFIG_USE_INIT = 0
default CONFIG_AP_CODE_IN_CAR = 0
-default MEM_TRAIN_SEQ = 2
-default WAIT_BEFORE_CPUS_INIT = 0
+default CONFIG_MEM_TRAIN_SEQ = 2
+default CONFIG_WAIT_BEFORE_CPUS_INIT = 0
default CONFIG_IOAPIC = 1
-default MAINBOARD_PART_NUMBER = "K9N Neo (MS-7260)"
-default MAINBOARD_VENDOR = "MSI"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID = 0x1462
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID = 0x7260
-default ROM_IMAGE_SIZE = 65536
-default STACK_SIZE = 0x2000
-default HEAP_SIZE = 0x8000
-default USE_OPTION_TABLE = (!USE_FALLBACK_IMAGE) && (!USE_FAILOVER_IMAGE)
-default _RAMBASE = 0x00100000
+default CONFIG_MAINBOARD_PART_NUMBER = "K9N Neo (MS-7260)"
+default CONFIG_MAINBOARD_VENDOR = "MSI"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID = 0x1462
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID = 0x7260
+default CONFIG_ROM_IMAGE_SIZE = 65536
+default CONFIG_STACK_SIZE = 0x2000
+default CONFIG_HEAP_SIZE = 0x8000
+default CONFIG_USE_OPTION_TABLE = (!CONFIG_USE_FALLBACK_IMAGE) && (!CONFIG_USE_FAILOVER_IMAGE)
+default CONFIG_RAMBASE = 0x00100000
default CONFIG_ROM_PAYLOAD = 1
-default CC = "$(CROSS_COMPILE)gcc -m32"
-default HOSTCC = "gcc"
+default CC = "$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC = "gcc"
default CONFIG_USE_PRINTK_IN_CAR = 1
default CONFIG_CONSOLE_SERIAL8250 = 1
-default TTYS0_BAUD = 115200
-default TTYS0_BASE = 0x3f8
-default TTYS0_LCS = 0x3
-default DEFAULT_CONSOLE_LOGLEVEL = 9
-default MAXIMUM_CONSOLE_LOGLEVEL = 9
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL = "MAINBOARD_POWER_ON"
+default CONFIG_TTYS0_BAUD = 115200
+default CONFIG_TTYS0_BASE = 0x3f8
+default CONFIG_TTYS0_LCS = 0x3
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL = "MAINBOARD_POWER_ON"
#
# CBFS
void hardwaremain(int ret_addr)
{
- struct sys_info *sysinfo = (DCACHE_RAM_BASE + DCACHE_RAM_SIZE -
- DCACHE_RAM_GLOBAL_VAR_SIZE); /* in CACHE */
+ struct sys_info *sysinfo = (CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE -
+ CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE); /* in CACHE */
struct sys_info *sysinfox = ((CONFIG_LB_MEM_TOPK << 10) -
- DCACHE_RAM_GLOBAL_VAR_SIZE); /* in RAM */
+ CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE); /* in RAM */
struct node_core_id id;
id = get_node_core_id_x();
/* If we want to wait for core1 done before DQS training, set it to 0. */
#define K8_SET_FIDVID_CORE0_ONLY 1
-#if K8_REV_F_SUPPORT == 1
+#if CONFIG_K8_REV_F_SUPPORT == 1
#define K8_REV_F_SUPPORT_F0_F1_WORKAROUND 0
#endif
#include "option_table.h"
#include "pc80/mc146818rtc_early.c"
-#if USE_FAILOVER_IMAGE == 0
+#if CONFIG_USE_FAILOVER_IMAGE == 0
#include "pc80/serial.c"
#include "arch/i386/lib/console.c"
#include "superio/winbond/w83627ehg/w83627ehg_early_serial.c"
#include "superio/winbond/w83627ehg/w83627ehg_early_init.c"
-#if USE_FAILOVER_IMAGE == 0
+#if CONFIG_USE_FAILOVER_IMAGE == 0
#include "cpu/x86/bist.h"
#include "northbridge/amd/amdk8/debug.c"
#endif
-#if ((HAVE_FAILOVER_BOOT==1) && (USE_FAILOVER_IMAGE == 1)) || ((HAVE_FAILOVER_BOOT==0) && (USE_FALLBACK_IMAGE == 1))
+#if ((CONFIG_HAVE_FAILOVER_BOOT==1) && (CONFIG_USE_FAILOVER_IMAGE == 1)) || ((CONFIG_HAVE_FAILOVER_BOOT==0) && (CONFIG_USE_FALLBACK_IMAGE == 1))
#include "southbridge/nvidia/mcp55/mcp55_enable_rom.c"
#include "northbridge/amd/amdk8/early_ht.c"
);
fallback_image:
-#if HAVE_FAILOVER_BOOT==1
+#if CONFIG_HAVE_FAILOVER_BOOT==1
__asm__ volatile ("jmp __fallback_image":
:"a" (bist), "b"(cpu_init_detectedx)
)
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
-#if HAVE_FAILOVER_BOOT == 1
-#if USE_FAILOVER_IMAGE == 1
+#if CONFIG_HAVE_FAILOVER_BOOT == 1
+#if CONFIG_USE_FAILOVER_IMAGE == 1
failover_process(bist, cpu_init_detectedx);
#else
real_main(bist, cpu_init_detectedx);
#endif
#else
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
failover_process(bist, cpu_init_detectedx);
#endif
real_main(bist, cpu_init_detectedx);
#endif
}
-#if USE_FAILOVER_IMAGE == 0
+#if CONFIG_USE_FAILOVER_IMAGE == 0
void real_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
};
struct sys_info *sysinfo =
- (DCACHE_RAM_BASE + DCACHE_RAM_SIZE - DCACHE_RAM_GLOBAL_VAR_SIZE);
+ (CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE);
int needs_reset = 0;
unsigned bsp_apicid = 0;
pnp_enter_ext_func_mode(SERIAL_DEV);
/* Switch CLKSEL to 24MHz (default is 48MHz). Needed for serial! */
pnp_write_config(SERIAL_DEV, 0x24, 0);
- w83627ehg_enable_dev(SERIAL_DEV, TTYS0_BASE);
+ w83627ehg_enable_dev(SERIAL_DEV, CONFIG_TTYS0_BASE);
pnp_exit_ext_func_mode(SERIAL_DEV);
setup_mb_resource_map();
print_debug_hex8(bsp_apicid);
print_debug("\r\n");
-#if MEM_TRAIN_SEQ == 1
+#if CONFIG_MEM_TRAIN_SEQ == 1
/* In BSP so could hold all AP until sysinfo is in RAM. */
set_sysinfo_in_ram(0);
#endif
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
arch i386 end
#needed by irq_tables and mptable and acpi_tables
object get_bus_conf.o
-if HAVE_MP_TABLE
+if CONFIG_HAVE_MP_TABLE
object mptable.o
end
-if HAVE_PIRQ_TABLE
+if CONFIG_HAVE_PIRQ_TABLE
object irq_tables.o
end
if CONFIG_USE_INIT
# compile cache_as_ram.c to auto.o
makerule ./cache_as_ram_auto.o
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
end
else
#compile cache_as_ram.c to auto.inc
makerule ./cache_as_ram_auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
## Build our 16 bit and 32 bit coreboot entry code
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
end
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
end
device pci 2.0 on end # USB 0x0223
device pci 2.1 on end # USB
device pci 2.2 on end # USB
- #when HT_CHAIN_END_UNITID_BASE (0,1) < HT_CHAIN_UNITID_BASE (6,,,,),
+ #when CONFIG_HT_CHAIN_END_UNITID_BASE (0,1) < CONFIG_HT_CHAIN_UNITID_BASE (6,,,,),
chip drivers/pci/onboard
device pci 3.0 on end # it is in bcm5785_0 bus, but the device id can not be changed even unitid is changed, fake one to get the rom_address
- # if HT_CHAIN_END_UNITID_BASE=0, it is 4, if HT_CHAIN_END_UNITID_BASE=1, it is 3
+ # if CONFIG_HT_CHAIN_END_UNITID_BASE=0, it is 4, if CONFIG_HT_CHAIN_END_UNITID_BASE=1, it is 3
register "rom_address" = "0xfff80000"
end
#bx_a013+ start
#bx_a013+ end
end
- #when HT_CHAIN_END_UNITID_BASE > HT_CHAIN_UNITID_BASE (6, ,,,,)
+ #when CONFIG_HT_CHAIN_END_UNITID_BASE > CONFIG_HT_CHAIN_UNITID_BASE (6, ,,,,)
# chip drivers/pci/onboard
# device pci 0.0 on end # fake, will be disabled
# end
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses HAVE_ACPI_TABLES
-uses HAVE_ACPI_RESUME
-uses ACPI_SSDTX_NUM
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_HAVE_ACPI_TABLES
+uses CONFIG_HAVE_ACPI_RESUME
+uses CONFIG_ACPI_SSDTX_NUM
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_MAX_CPUS
uses CONFIG_MAX_PHYSICAL_CPUS
uses CONFIG_LOGICAL_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
-uses _RAMBASE
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_RAMBASE
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_SERIAL8250
-uses HAVE_INIT_TIMER
+uses CONFIG_HAVE_INIT_TIMER
uses CONFIG_GDB_STUB
uses CONFIG_GDB_STUB
-uses CROSS_COMPILE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
-uses HW_MEM_HOLE_SIZEK
-uses HW_MEM_HOLE_SIZE_AUTO_INC
-uses K8_HT_FREQ_1G_SUPPORT
-
-uses HT_CHAIN_UNITID_BASE
-uses HT_CHAIN_END_UNITID_BASE
-uses SB_HT_CHAIN_ON_BUS0
-uses SB_HT_CHAIN_UNITID_OFFSET_ONLY
-
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
-uses DCACHE_RAM_GLOBAL_VAR_SIZE
+uses CONFIG_HW_MEM_HOLE_SIZEK
+uses CONFIG_HW_MEM_HOLE_SIZE_AUTO_INC
+uses CONFIG_K8_HT_FREQ_1G_SUPPORT
+
+uses CONFIG_HT_CHAIN_UNITID_BASE
+uses CONFIG_HT_CHAIN_END_UNITID_BASE
+uses CONFIG_SB_HT_CHAIN_ON_BUS0
+uses CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY
+
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
+uses CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE
uses CONFIG_USE_INIT
-uses SERIAL_CPU_INIT
+uses CONFIG_SERIAL_CPU_INIT
-uses ENABLE_APIC_EXT_ID
-uses APIC_ID_OFFSET
-uses LIFT_BSP_APIC_ID
+uses CONFIG_ENABLE_APIC_EXT_ID
+uses CONFIG_APIC_ID_OFFSET
+uses CONFIG_LIFT_BSP_APIC_ID
uses CONFIG_PCI_64BIT_PREF_MEM
###
##
-## ROM_SIZE is the size of boot ROM that this board will use.
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
##
-default ROM_SIZE=524288
+default CONFIG_ROM_SIZE=524288
##
-## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
+## CONFIG_FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
##
-#default FALLBACK_SIZE=131072
+#default CONFIG_FALLBACK_SIZE=131072
#256K
-default FALLBACK_SIZE=0x40000
+default CONFIG_FALLBACK_SIZE=0x40000
#more 1M for pgtbl
default CONFIG_LB_MEM_TOPK=2048
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=11
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=11
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
## ACPI tables will be included
-#default HAVE_ACPI_TABLES=1
+#default CONFIG_HAVE_ACPI_TABLES=1
## extra SSDT num
-#default ACPI_SSDTX_NUM=1
+#default CONFIG_ACPI_SSDTX_NUM=1
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
##
## Move the default coreboot cmos range off of AMD RTC registers
##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
+default CONFIG_LB_CKS_RANGE_START=49
+default CONFIG_LB_CKS_RANGE_END=122
+default CONFIG_LB_CKS_LOC=123
##
## Build code for SMP support
default CONFIG_MAX_PHYSICAL_CPUS=2
default CONFIG_LOGICAL_CPUS=1
-default SERIAL_CPU_INIT=0
+default CONFIG_SERIAL_CPU_INIT=0
-default ENABLE_APIC_EXT_ID=0
-default APIC_ID_OFFSET=0x8
-default LIFT_BSP_APIC_ID=1
+default CONFIG_ENABLE_APIC_EXT_ID=0
+default CONFIG_APIC_ID_OFFSET=0x8
+default CONFIG_LIFT_BSP_APIC_ID=1
#memory hole size, 0 mean disable, others will enable the hole, at that case if it is small than mmio_basek, it will use mmio_basek instead.
#2G
-#default HW_MEM_HOLE_SIZEK=0x200000
+#default CONFIG_HW_MEM_HOLE_SIZEK=0x200000
#1G
-default HW_MEM_HOLE_SIZEK=0x100000
+default CONFIG_HW_MEM_HOLE_SIZEK=0x100000
#512M
-#default HW_MEM_HOLE_SIZEK=0x80000
+#default CONFIG_HW_MEM_HOLE_SIZEK=0x80000
#make auto increase hole size to avoid hole_startk equal to basek so as to make some kernel happy
-#default HW_MEM_HOLE_SIZE_AUTO_INC=1
+#default CONFIG_HW_MEM_HOLE_SIZE_AUTO_INC=1
#Opteron K8 1G HT Support
-default K8_HT_FREQ_1G_SUPPORT=1
+default CONFIG_K8_HT_FREQ_1G_SUPPORT=1
#VGA Console
default CONFIG_CONSOLE_VGA=1
default CONFIG_PCI_ROM_RUN=1
#HT Unit ID offset, default is 1, the typical one
-default HT_CHAIN_UNITID_BASE=0x06
+default CONFIG_HT_CHAIN_UNITID_BASE=0x06
#real SB Unit ID, default is 0x20, mean dont touch it at last
-default HT_CHAIN_END_UNITID_BASE=0x01
+default CONFIG_HT_CHAIN_END_UNITID_BASE=0x01
#make the SB HT chain on bus 0, default is not (0)
-default SB_HT_CHAIN_ON_BUS0=2
+default CONFIG_SB_HT_CHAIN_ON_BUS0=2
#only offset for SB chain?, default is yes(1)
-#default SB_HT_CHAIN_UNITID_OFFSET_ONLY=0
+#default CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY=0
#allow capable device use that above 4G
#default CONFIG_PCI_64BIT_PREF_MEM=1
##
## enable CACHE_AS_RAM specifics
##
-default USE_DCACHE_RAM=1
-default DCACHE_RAM_BASE=0xcc000
-default DCACHE_RAM_SIZE=0x04000
-default DCACHE_RAM_GLOBAL_VAR_SIZE=0x01000
+default CONFIG_USE_DCACHE_RAM=1
+default CONFIG_DCACHE_RAM_BASE=0xcc000
+default CONFIG_DCACHE_RAM_SIZE=0x04000
+default CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE=0x01000
default CONFIG_USE_INIT=0
##
##
## Clean up the motherboard id strings
##
-default MAINBOARD_PART_NUMBER="MS9185"
-default MAINBOARD_VENDOR="MSI"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x1022
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2b80
+default CONFIG_MAINBOARD_PART_NUMBER="MS9185"
+default CONFIG_MAINBOARD_VENDOR="MSI"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x1022
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2b80
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 32K heap
##
-default HEAP_SIZE=0x8000
+default CONFIG_HEAP_SIZE=0x8000
##
## Only use the option table in a normal image
##
-default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
##
## Coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00100000
+default CONFIG_RAMBASE=0x00100000
##
## Load the payload from the ROM
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## Disable the gdb stub by default
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
### End Options.lb
#
#include "cpu/amd/model_fxx/fidvid.c"
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
#include "northbridge/amd/amdk8/early_ht.c"
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
failover_process(bist, cpu_init_detectedx);
#endif
real_main(bist, cpu_init_detectedx);
};
- struct sys_info *sysinfo = (DCACHE_RAM_BASE + DCACHE_RAM_SIZE - DCACHE_RAM_GLOBAL_VAR_SIZE);
+ struct sys_info *sysinfo = (CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE);
int needs_reset;
unsigned bsp_apicid = 0;
// post_code(0x32);
- pc87417_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ pc87417_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
-// dump_mem(DCACHE_RAM_BASE+DCACHE_RAM_SIZE-0x200, DCACHE_RAM_BASE+DCACHE_RAM_SIZE);
+// dump_mem(CONFIG_DCACHE_RAM_BASE+CONFIG_DCACHE_RAM_SIZE-0x200, CONFIG_DCACHE_RAM_BASE+CONFIG_DCACHE_RAM_SIZE);
/* Halt if there was a built in self test failure */
report_bist_failure(bist);
dev = dev_find_slot(m->bus_bcm5785_1, PCI_DEVFN(0xd,0));
if(dev) {
m->bus_bcm5785_1_1 = pci_read_config8(dev, PCI_SECONDARY_BUS);
-#if HT_CHAIN_END_UNITID_BASE >= HT_CHAIN_UNITID_BASE
+#if CONFIG_HT_CHAIN_END_UNITID_BASE >= CONFIG_HT_CHAIN_UNITID_BASE
m->bus_isa = pci_read_config8(dev, PCI_SUBORDINATE_BUS);
m->bus_isa++;
printk_debug("bus_isa=%d\n",m->bus_isa);
dev = dev_find_slot(m->bus_bcm5780[0], PCI_DEVFN(m->sbdn2 + i - 1,0));
if(dev) {
m->bus_bcm5780[i] = pci_read_config8(dev, PCI_SECONDARY_BUS);
-#if HT_CHAIN_END_UNITID_BASE < HT_CHAIN_UNITID_BASE
+#if CONFIG_HT_CHAIN_END_UNITID_BASE < CONFIG_HT_CHAIN_UNITID_BASE
m->bus_isa = pci_read_config8(dev, PCI_SUBORDINATE_BUS);
m->bus_isa++;
printk_debug("bus_isa=%d\n",m->bus_isa);
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
default CONFIG_ROM_PAYLOAD = 1
object get_bus_conf.o
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
#object reset.o
if CONFIG_USE_INIT
makerule ./auto.o
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
end
else
makerule ./auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
##
## Build our 16 bit and 32 bit coreboot entry code
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
end
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
##
## ROMSTRAP table for MCP55
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit southbridge/nvidia/mcp55/romstrap.inc
ldscript /southbridge/nvidia/mcp55/romstrap.lds
end
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
end
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_MAX_CPUS
uses CONFIG_MAX_PHYSICAL_CPUS
uses CONFIG_LOGICAL_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
-uses _RAMBASE
+uses CONFIG_RAMBASE
uses CONFIG_GDB_STUB
-uses CROSS_COMPILE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_SERIAL8250
-uses HAVE_INIT_TIMER
+uses CONFIG_HAVE_INIT_TIMER
uses CONFIG_GDB_STUB
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
#bx_b001- uses K8_HW_MEM_HOLE_SIZEK
-uses K8_HT_FREQ_1G_SUPPORT
+uses CONFIG_K8_HT_FREQ_1G_SUPPORT
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
-uses DCACHE_RAM_GLOBAL_VAR_SIZE
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
+uses CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE
uses CONFIG_USE_INIT
-uses ENABLE_APIC_EXT_ID
-uses APIC_ID_OFFSET
-uses LIFT_BSP_APIC_ID
+uses CONFIG_ENABLE_APIC_EXT_ID
+uses CONFIG_APIC_ID_OFFSET
+uses CONFIG_LIFT_BSP_APIC_ID
-uses HT_CHAIN_UNITID_BASE
-uses HT_CHAIN_END_UNITID_BASE
+uses CONFIG_HT_CHAIN_UNITID_BASE
+uses CONFIG_HT_CHAIN_END_UNITID_BASE
#bx_b001- uses K8_SB_HT_CHAIN_ON_BUS0
-uses SB_HT_CHAIN_UNITID_OFFSET_ONLY
+uses CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY
#bx_b005+
-uses SB_HT_CHAIN_ON_BUS0
+uses CONFIG_SB_HT_CHAIN_ON_BUS0
# stepan 2007-04-12
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
uses CONFIG_USE_PRINTK_IN_CAR
-## ROM_SIZE is the size of boot ROM that this board will use.
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
#512K bytes
-default ROM_SIZE=524288
+default CONFIG_ROM_SIZE=524288
#1M bytes
-#bx- default ROM_SIZE=1048576
+#bx- default CONFIG_ROM_SIZE=1048576
##
-## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
+## CONFIG_FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
##
-#default FALLBACK_SIZE=131072
+#default CONFIG_FALLBACK_SIZE=131072
#256K
-default FALLBACK_SIZE=0x40000
+default CONFIG_FALLBACK_SIZE=0x40000
###
### Build options
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=11
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=11
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
##
## Move the default coreboot cmos range off of AMD RTC registers
##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
+default CONFIG_LB_CKS_RANGE_START=49
+default CONFIG_LB_CKS_RANGE_END=122
+default CONFIG_LB_CKS_LOC=123
##
## Build code for SMP support
#bx_b001- default K8_HW_MEM_HOLE_SIZEK=0x100000
#Opteron K8 1G HT Support
-default K8_HT_FREQ_1G_SUPPORT=1
+default CONFIG_K8_HT_FREQ_1G_SUPPORT=1
##HT Unit ID offset, default is 1, the typical one
-default HT_CHAIN_UNITID_BASE=0x0
+default CONFIG_HT_CHAIN_UNITID_BASE=0x0
##real SB Unit ID, default is 0x20, mean dont touch it at last
-#default HT_CHAIN_END_UNITID_BASE=0x0
+#default CONFIG_HT_CHAIN_END_UNITID_BASE=0x0
#make the SB HT chain on bus 0, default is not (0)
#bx_b001- default K8_SB_HT_CHAIN_ON_BUS0=2
##bx_b005+ make the SB HT chain on bus 0
-default SB_HT_CHAIN_ON_BUS0=1
+default CONFIG_SB_HT_CHAIN_ON_BUS0=1
##only offset for SB chain?, default is yes(1)
-default SB_HT_CHAIN_UNITID_OFFSET_ONLY=0
+default CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY=0
#VGA
default CONFIG_CONSOLE_VGA=1
##
## enable CACHE_AS_RAM specifics
##
-default USE_DCACHE_RAM=1
-default DCACHE_RAM_BASE=0xcc000
-default DCACHE_RAM_SIZE=0x4000
-default DCACHE_RAM_GLOBAL_VAR_SIZE=0x01000
+default CONFIG_USE_DCACHE_RAM=1
+default CONFIG_DCACHE_RAM_BASE=0xcc000
+default CONFIG_DCACHE_RAM_SIZE=0x4000
+default CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE=0x01000
default CONFIG_USE_INIT=0
-default ENABLE_APIC_EXT_ID=1
-default APIC_ID_OFFSET=0x10
-default LIFT_BSP_APIC_ID=0
+default CONFIG_ENABLE_APIC_EXT_ID=1
+default CONFIG_APIC_ID_OFFSET=0x10
+default CONFIG_LIFT_BSP_APIC_ID=0
##
## Build code to setup a generic IOAPIC
##
## Clean up the motherboard id strings
##
-default MAINBOARD_PART_NUMBER="ms9282"
-default MAINBOARD_VENDOR="MSI"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x1462
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x9282
+default CONFIG_MAINBOARD_PART_NUMBER="ms9282"
+default CONFIG_MAINBOARD_VENDOR="MSI"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x1462
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x9282
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE=0x4000
+default CONFIG_HEAP_SIZE=0x4000
##
## Only use the option table in a normal image
##
-default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
##
## Coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00004000
+default CONFIG_RAMBASE=0x00004000
##
## Load the payload from the ROM
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## Disable the gdb stub by default
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
### End Options.lb
#
#include "cpu/amd/model_fxx/init_cpus.c"
#include "cpu/amd/model_fxx/fidvid.c"
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
#include "southbridge/nvidia/mcp55/mcp55_enable_rom.c"
#include "northbridge/amd/amdk8/early_ht.c"
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
failover_process(bist, cpu_init_detectedx);
#endif
real_main(bist, cpu_init_detectedx);
unsigned bsp_apicid = 0;
int needs_reset;
- struct sys_info *sysinfo = (DCACHE_RAM_BASE + DCACHE_RAM_SIZE - DCACHE_RAM_GLOBAL_VAR_SIZE);
+ struct sys_info *sysinfo = (CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE);
char *p ;
if (bist == 0) {
bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);
}
- w83627ehg_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ w83627ehg_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
arch i386 end
driver mainboard.o
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
# object reset.o
makerule ./failover.E
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -E -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -E -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./auto.E
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -E -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -E -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
mainboardinit cpu/x86/16bit/entry16.inc
mainboardinit cpu/x86/32bit/entry32.inc
ldscript /cpu/x86/16bit/entry16.lds
ldscript /cpu/x86/32bit/entry32.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
mainboardinit arch/i386/lib/cpu_reset.inc
mainboardinit arch/i386/lib/id.inc
ldscript /arch/i386/lib/id.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_ROM_PAYLOAD
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses HAVE_MP_TABLE
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
-default ROM_SIZE = 512 * 1024
-default HAVE_FALLBACK_BOOT = 1
-default HAVE_MP_TABLE = 0
-default HAVE_HARD_RESET = 0
-default HAVE_PIRQ_TABLE = 1
-default IRQ_SLOT_COUNT = 0 # Override this in targets/*/Config.lb.
-default MAINBOARD_VENDOR = "N/A" # Override this in targets/*/Config.lb.
-default MAINBOARD_PART_NUMBER = "N/A" # Override this in targets/*/Config.lb.
-default ROM_IMAGE_SIZE = 64 * 1024
-default FALLBACK_SIZE = 128 * 1024
-default STACK_SIZE = 8 * 1024
-default HEAP_SIZE = 16 * 1024
-default HAVE_OPTION_TABLE = 0
-#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_ROM_SIZE = 512 * 1024
+default CONFIG_HAVE_FALLBACK_BOOT = 1
+default CONFIG_HAVE_MP_TABLE = 0
+default CONFIG_HAVE_HARD_RESET = 0
+default CONFIG_HAVE_PIRQ_TABLE = 1
+default CONFIG_IRQ_SLOT_COUNT = 0 # Override this in targets/*/Config.lb.
+default CONFIG_MAINBOARD_VENDOR = "N/A" # Override this in targets/*/Config.lb.
+default CONFIG_MAINBOARD_PART_NUMBER = "N/A" # Override this in targets/*/Config.lb.
+default CONFIG_ROM_IMAGE_SIZE = 64 * 1024
+default CONFIG_FALLBACK_SIZE = 128 * 1024
+default CONFIG_STACK_SIZE = 8 * 1024
+default CONFIG_HEAP_SIZE = 16 * 1024
+default CONFIG_HAVE_OPTION_TABLE = 0
+#default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 0
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
-default CROSS_COMPILE = ""
-default CC = "$(CROSS_COMPILE)gcc -m32"
-default HOSTCC = "gcc"
+default CONFIG_CROSS_COMPILE = ""
+default CC = "$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC = "gcc"
default CONFIG_CONSOLE_SERIAL8250 = 1
-default TTYS0_BAUD = 115200
-default TTYS0_BASE = 0x3f8
-default TTYS0_LCS = 0x3 # 8n1
-default DEFAULT_CONSOLE_LOGLEVEL = 9
-default MAXIMUM_CONSOLE_LOGLEVEL = 9
+default CONFIG_TTYS0_BAUD = 115200
+default CONFIG_TTYS0_BASE = 0x3f8
+default CONFIG_TTYS0_LCS = 0x3 # 8n1
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
default CONFIG_UDELAY_TSC = 1
default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 1
default CONFIG_CONSOLE_VGA = 1
if (bist == 0)
early_mtrr_init();
- smscsuperio_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ smscsuperio_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
const struct irq_routing_table intel_irq_routing_table = {
PIRQ_SIGNATURE,
PIRQ_VERSION,
- 32 + 16 * IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
+ 32 + 16 * CONFIG_IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
0x00, /* Interrupt router bus */
(0x1f << 3) | 0x0, /* Interrupt router device */
0, /* IRQs devoted exclusively to PCI usage */
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
##
##
driver mainboard.o
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
#object reset.o
if CONFIG_USE_INIT
makerule ./auto.o
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
end
else
makerule ./auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
##
## Build our 16 bit and 32 bit coreboot entry code
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
end
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
end
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_MAX_CPUS
uses CONFIG_MAX_PHYSICAL_CPUS
uses CONFIG_LOGICAL_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
-uses _RAMBASE
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_RAMBASE
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_SERIAL8250
-uses HAVE_INIT_TIMER
+uses CONFIG_HAVE_INIT_TIMER
uses CONFIG_GDB_STUB
-uses CROSS_COMPILE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
-uses HW_MEM_HOLE_SIZEK
+uses CONFIG_HW_MEM_HOLE_SIZEK
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
uses CONFIG_USE_INIT
uses CONFIG_USE_PRINTK_IN_CAR
###
##
-## ROM_SIZE is the size of boot ROM that this board will use.
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
##
-default ROM_SIZE=524288
+default CONFIG_ROM_SIZE=524288
##
-## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
+## CONFIG_FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
##
-#default FALLBACK_SIZE=131072
+#default CONFIG_FALLBACK_SIZE=131072
#256K
-default FALLBACK_SIZE=0x40000
+default CONFIG_FALLBACK_SIZE=0x40000
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=15
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=15
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
##
## Move the default coreboot cmos range off of AMD RTC registers
##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
+default CONFIG_LB_CKS_RANGE_START=49
+default CONFIG_LB_CKS_RANGE_END=122
+default CONFIG_LB_CKS_LOC=123
##
## Build code for SMP support
default CONFIG_LOGICAL_CPUS=1
#1G memory hole
-default HW_MEM_HOLE_SIZEK=0x100000
+default CONFIG_HW_MEM_HOLE_SIZEK=0x100000
#VGA Console
default CONFIG_CONSOLE_VGA=1
##
## enable CACHE_AS_RAM specifics
##
-default USE_DCACHE_RAM=1
-default DCACHE_RAM_BASE=0xcf000
-default DCACHE_RAM_SIZE=0x1000
+default CONFIG_USE_DCACHE_RAM=1
+default CONFIG_DCACHE_RAM_BASE=0xcf000
+default CONFIG_DCACHE_RAM_SIZE=0x1000
default CONFIG_USE_INIT=0
##
##
## Clean up the motherboard id strings
##
-default MAINBOARD_PART_NUMBER="Khepri"
-default MAINBOARD_VENDOR="Newisys"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x17c2
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x0010
+default CONFIG_MAINBOARD_PART_NUMBER="Khepri"
+default CONFIG_MAINBOARD_VENDOR="Newisys"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x17c2
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x0010
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE=0x4000
+default CONFIG_HEAP_SIZE=0x4000
##
## Only use the option table in a normal image
##
-default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
##
## Coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00004000
+default CONFIG_RAMBASE=0x00004000
##
## Load the payload from the ROM
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## Disable the gdb stub by default
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
### End Options.lb
#
#include "cpu/amd/model_fxx/init_cpus.c"
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
#include "southbridge/amd/amd8111/amd8111_enable_rom.c"
#include "northbridge/amd/amdk8/early_ht.c"
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
failover_process(bist, cpu_init_detectedx);
#endif
real_main(bist, cpu_init_detectedx);
// post_code(0x32);
- w83627hf_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ w83627hf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
-// dump_mem(DCACHE_RAM_BASE+DCACHE_RAM_SIZE-0x200, DCACHE_RAM_BASE+DCACHE_RAM_SIZE);
+// dump_mem(CONFIG_DCACHE_RAM_BASE+CONFIG_DCACHE_RAM_SIZE-0x200, CONFIG_DCACHE_RAM_BASE+CONFIG_DCACHE_RAM_SIZE);
/* Halt if there was a built in self test failure */
report_bist_failure(bist);
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/failovercalculation.lb
arch i386 end
#needed by irq_tables and mptable and acpi_tables
object get_bus_conf.o
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
#object reset.o
-if HAVE_ACPI_TABLES
+if CONFIG_HAVE_ACPI_TABLES
object acpi_tables.o
object fadt.o
makerule dsdt.c
- depends "$(MAINBOARD)/dx/dsdt_lb.dsl"
- action "/usr/sbin/iasl -tc $(MAINBOARD)/dx/dsdt_lb.dsl"
+ depends "$(CONFIG_MAINBOARD)/dx/dsdt_lb.dsl"
+ action "/usr/sbin/iasl -tc $(CONFIG_MAINBOARD)/dx/dsdt_lb.dsl"
action "mv dsdt_lb.hex dsdt.c"
end
object ./dsdt.o
#./ssdt.o is moved to northbridge/amd/amdk8/Config.lb
- if ACPI_SSDTX_NUM
+ if CONFIG_ACPI_SSDTX_NUM
makerule ssdt6.c
- depends "$(MAINBOARD)/dx/pci6.asl"
- action "/usr/sbin/iasl -tc $(MAINBOARD)/dx/pci6.asl"
+ depends "$(CONFIG_MAINBOARD)/dx/pci6.asl"
+ action "/usr/sbin/iasl -tc $(CONFIG_MAINBOARD)/dx/pci6.asl"
action "perl -pi -e 's/AmlCode/AmlCode_ssdt6/g' pci6.hex"
action "mv pci6.hex ssdt6.c"
end
object ./ssdt6.o
makerule ssdt5.c
- depends "$(MAINBOARD)/dx/pci5.asl"
- action "/usr/sbin/iasl -tc $(MAINBOARD)/dx/pci5.asl"
+ depends "$(CONFIG_MAINBOARD)/dx/pci5.asl"
+ action "/usr/sbin/iasl -tc $(CONFIG_MAINBOARD)/dx/pci5.asl"
action "perl -pi -e 's/AmlCode/AmlCode_ssdt5/g' pci5.hex"
action "mv pci5.hex ssdt5.c"
end
if CONFIG_USE_INIT
makerule ./cache_as_ram_auto.o
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
end
else
makerule ./cache_as_ram_auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
end
-if USE_FAILOVER_IMAGE
+if CONFIG_USE_FAILOVER_IMAGE
else
if CONFIG_AP_CODE_IN_CAR
makerule ./apc_auto.o
- depends "$(MAINBOARD)/apc_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/apc_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/apc_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/apc_auto.c -o $@"
end
ldscript /arch/i386/init/ldscript_apc.lb
end
##
## Build our 16 bit and 32 bit coreboot entry code
##
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
end
##
## Build our reset vector (This is where coreboot is entered)
##
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
ldscript /cpu/x86/32bit/reset32.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
##
## ROMSTRAP table for MCP55
##
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
mainboardinit southbridge/nvidia/mcp55/romstrap.inc
ldscript /southbridge/nvidia/mcp55/romstrap.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
mainboardinit southbridge/nvidia/mcp55/romstrap.inc
ldscript /southbridge/nvidia/mcp55/romstrap.lds
end
### Things are delicate and we test to see if we should
### failover to another image.
###
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
ldscript /arch/i386/lib/failover_failover.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
end
end
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses HAVE_ACPI_TABLES
-uses HAVE_ACPI_RESUME
-uses ACPI_SSDTX_NUM
-uses USE_FALLBACK_IMAGE
-uses USE_FAILOVER_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_FAILOVER_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_HAVE_ACPI_TABLES
+uses CONFIG_HAVE_ACPI_RESUME
+uses CONFIG_ACPI_SSDTX_NUM
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_USE_FAILOVER_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_FAILOVER_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_MAX_CPUS
uses CONFIG_MAX_PHYSICAL_CPUS
uses CONFIG_LOGICAL_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses FAILOVER_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_FAILOVER_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_NRV2B
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
-uses _RAMBASE
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_RAMBASE
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_SERIAL8250
-uses HAVE_INIT_TIMER
+uses CONFIG_HAVE_INIT_TIMER
uses CONFIG_GDB_STUB
uses CONFIG_GDB_STUB
-uses CROSS_COMPILE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
uses CONFIG_CONSOLE_VGA
uses CONFIG_USBDEBUG_DIRECT
uses CONFIG_PCI_ROM_RUN
-uses HW_MEM_HOLE_SIZEK
-uses HW_MEM_HOLE_SIZE_AUTO_INC
-uses K8_HT_FREQ_1G_SUPPORT
-
-uses HT_CHAIN_UNITID_BASE
-uses HT_CHAIN_END_UNITID_BASE
-uses SB_HT_CHAIN_ON_BUS0
-uses SB_HT_CHAIN_UNITID_OFFSET_ONLY
-
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
-uses DCACHE_RAM_GLOBAL_VAR_SIZE
+uses CONFIG_HW_MEM_HOLE_SIZEK
+uses CONFIG_HW_MEM_HOLE_SIZE_AUTO_INC
+uses CONFIG_K8_HT_FREQ_1G_SUPPORT
+
+uses CONFIG_HT_CHAIN_UNITID_BASE
+uses CONFIG_HT_CHAIN_END_UNITID_BASE
+uses CONFIG_SB_HT_CHAIN_ON_BUS0
+uses CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY
+
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
+uses CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE
uses CONFIG_USE_INIT
-uses SERIAL_CPU_INIT
+uses CONFIG_SERIAL_CPU_INIT
-uses ENABLE_APIC_EXT_ID
-uses APIC_ID_OFFSET
-uses LIFT_BSP_APIC_ID
+uses CONFIG_ENABLE_APIC_EXT_ID
+uses CONFIG_APIC_ID_OFFSET
+uses CONFIG_LIFT_BSP_APIC_ID
uses CONFIG_PCI_64BIT_PREF_MEM
uses CONFIG_AP_CODE_IN_CAR
-uses MEM_TRAIN_SEQ
+uses CONFIG_MEM_TRAIN_SEQ
-uses WAIT_BEFORE_CPUS_INIT
+uses CONFIG_WAIT_BEFORE_CPUS_INIT
uses CONFIG_USE_PRINTK_IN_CAR
###
##
-## ROM_SIZE is the size of boot ROM that this board will use.
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
##
-default ROM_SIZE=524288
-#default ROM_SIZE=0x100000
+default CONFIG_ROM_SIZE=524288
+#default CONFIG_ROM_SIZE=0x100000
##
-## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
+## CONFIG_FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
##
-#default FALLBACK_SIZE=131072
-#default FALLBACK_SIZE=0x40000
+#default CONFIG_FALLBACK_SIZE=131072
+#default CONFIG_FALLBACK_SIZE=0x40000
#FALLBACK: 256K-4K
-default FALLBACK_SIZE=0x3f000
+default CONFIG_FALLBACK_SIZE=0x3f000
#FAILOVER: 4K
-default FAILOVER_SIZE=0x01000
+default CONFIG_FAILOVER_SIZE=0x01000
#more 1M for pgtbl
default CONFIG_LB_MEM_TOPK=2048
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
-default HAVE_FAILOVER_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FAILOVER_BOOT=1
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=11
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=11
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
## ACPI tables will be included
-default HAVE_ACPI_TABLES=0
+default CONFIG_HAVE_ACPI_TABLES=0
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
##
## Move the default coreboot cmos range off of AMD RTC registers
##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
+default CONFIG_LB_CKS_RANGE_START=49
+default CONFIG_LB_CKS_RANGE_END=122
+default CONFIG_LB_CKS_LOC=123
##
## Build code for SMP support
default CONFIG_MAX_PHYSICAL_CPUS=2
default CONFIG_LOGICAL_CPUS=1
-#default SERIAL_CPU_INIT=0
+#default CONFIG_SERIAL_CPU_INIT=0
-default ENABLE_APIC_EXT_ID=0
-default APIC_ID_OFFSET=0x10
-default LIFT_BSP_APIC_ID=1
+default CONFIG_ENABLE_APIC_EXT_ID=0
+default CONFIG_APIC_ID_OFFSET=0x10
+default CONFIG_LIFT_BSP_APIC_ID=1
#memory hole size, 0 mean disable, others will enable the hole, at that case if it is small than mmio_basek, it will use mmio_basek instead.
#2G
-#default HW_MEM_HOLE_SIZEK=0x200000
+#default CONFIG_HW_MEM_HOLE_SIZEK=0x200000
#1G
-default HW_MEM_HOLE_SIZEK=0x100000
+default CONFIG_HW_MEM_HOLE_SIZEK=0x100000
#512M
-#default HW_MEM_HOLE_SIZEK=0x80000
+#default CONFIG_HW_MEM_HOLE_SIZEK=0x80000
#make auto increase hole size to avoid hole_startk equal to basek so as to make some kernel happy
-#default HW_MEM_HOLE_SIZE_AUTO_INC=1
+#default CONFIG_HW_MEM_HOLE_SIZE_AUTO_INC=1
#Opteron K8 1G HT Support
-default K8_HT_FREQ_1G_SUPPORT=1
+default CONFIG_K8_HT_FREQ_1G_SUPPORT=1
#VGA Console
default CONFIG_CONSOLE_VGA=1
#default CONFIG_USBDEBUG_DIRECT=1
#HT Unit ID offset, default is 1, the typical one, 0 mean only one HT device
-default HT_CHAIN_UNITID_BASE=0
+default CONFIG_HT_CHAIN_UNITID_BASE=0
#real SB Unit ID, default is 0x20, mean dont touch it at last
-#default HT_CHAIN_END_UNITID_BASE=0x6
+#default CONFIG_HT_CHAIN_END_UNITID_BASE=0x6
#make the SB HT chain on bus 0, default is not (0)
-default SB_HT_CHAIN_ON_BUS0=2
+default CONFIG_SB_HT_CHAIN_ON_BUS0=2
#only offset for SB chain?, default is yes(1)
-default SB_HT_CHAIN_UNITID_OFFSET_ONLY=0
+default CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY=0
#allow capable device use that above 4G
#default CONFIG_PCI_64BIT_PREF_MEM=1
##
## enable CACHE_AS_RAM specifics
##
-default USE_DCACHE_RAM=1
-default DCACHE_RAM_BASE=0xc8000
-default DCACHE_RAM_SIZE=0x08000
-default DCACHE_RAM_GLOBAL_VAR_SIZE=0x01000
+default CONFIG_USE_DCACHE_RAM=1
+default CONFIG_DCACHE_RAM_BASE=0xc8000
+default CONFIG_DCACHE_RAM_SIZE=0x08000
+default CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE=0x01000
default CONFIG_USE_INIT=0
default CONFIG_AP_CODE_IN_CAR=0
-default MEM_TRAIN_SEQ=1
-default WAIT_BEFORE_CPUS_INIT=1
+default CONFIG_MEM_TRAIN_SEQ=1
+default CONFIG_WAIT_BEFORE_CPUS_INIT=1
##
## Build code to setup a generic IOAPIC
##
## Clean up the motherboard id strings
##
-default MAINBOARD_PART_NUMBER="l1_2pvv"
-default MAINBOARD_VENDOR="NVIDIA"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x1022
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2b80
+default CONFIG_MAINBOARD_PART_NUMBER="l1_2pvv"
+default CONFIG_MAINBOARD_VENDOR="NVIDIA"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x1022
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2b80
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 32K heap
##
-default HEAP_SIZE=0x8000
+default CONFIG_HEAP_SIZE=0x8000
##
## Only use the option table in a normal image
##
-default USE_OPTION_TABLE = (!USE_FALLBACK_IMAGE) && (!USE_FAILOVER_IMAGE )
+default CONFIG_USE_OPTION_TABLE = (!CONFIG_USE_FALLBACK_IMAGE) && (!CONFIG_USE_FAILOVER_IMAGE )
##
## Coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00100000
+default CONFIG_RAMBASE=0x00100000
##
## Load the payload from the ROM
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## Disable the gdb stub by default
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
### End Options.lb
#
void hardwaremain(int ret_addr)
{
- struct sys_info *sysinfo = (DCACHE_RAM_BASE + DCACHE_RAM_SIZE - DCACHE_RAM_GLOBAL_VAR_SIZE); // in CACHE
- struct sys_info *sysinfox = ((CONFIG_LB_MEM_TOPK<<10) - DCACHE_RAM_GLOBAL_VAR_SIZE); // in RAM
+ struct sys_info *sysinfo = (CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE); // in CACHE
+ struct sys_info *sysinfox = ((CONFIG_LB_MEM_TOPK<<10) - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE); // in RAM
struct node_core_id id;
//if we want to wait for core1 done before DQS training, set it to 0
#define K8_SET_FIDVID_CORE0_ONLY 1
-#if K8_REV_F_SUPPORT == 1
+#if CONFIG_K8_REV_F_SUPPORT == 1
#define K8_REV_F_SUPPORT_F0_F1_WORKAROUND 0
#endif
#include "option_table.h"
#include "pc80/mc146818rtc_early.c"
-#if USE_FAILOVER_IMAGE==0
+#if CONFIG_USE_FAILOVER_IMAGE==0
#include "pc80/serial.c"
#include "arch/i386/lib/console.c"
#if CONFIG_USBDEBUG_DIRECT
#include "superio/winbond/w83627ehg/w83627ehg_early_serial.c"
#include "superio/winbond/w83627ehg/w83627ehg_early_init.c"
-#if USE_FAILOVER_IMAGE==0
+#if CONFIG_USE_FAILOVER_IMAGE==0
#include "cpu/x86/bist.h"
#endif
-#if ((HAVE_FAILOVER_BOOT==1) && (USE_FAILOVER_IMAGE == 1)) || ((HAVE_FAILOVER_BOOT==0) && (USE_FALLBACK_IMAGE == 1))
+#if ((CONFIG_HAVE_FAILOVER_BOOT==1) && (CONFIG_USE_FAILOVER_IMAGE == 1)) || ((CONFIG_HAVE_FAILOVER_BOOT==0) && (CONFIG_USE_FALLBACK_IMAGE == 1))
#include "southbridge/nvidia/mcp55/mcp55_enable_rom.c"
#include "northbridge/amd/amdk8/early_ht.c"
);
fallback_image:
-#if HAVE_FAILOVER_BOOT==1
+#if CONFIG_HAVE_FAILOVER_BOOT==1
__asm__ volatile ("jmp __fallback_image"
: /* outputs */
: "a" (bist), "b" (cpu_init_detectedx) /* inputs */
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
-#if HAVE_FAILOVER_BOOT==1
- #if USE_FAILOVER_IMAGE==1
+#if CONFIG_HAVE_FAILOVER_BOOT==1
+ #if CONFIG_USE_FAILOVER_IMAGE==1
failover_process(bist, cpu_init_detectedx);
#else
real_main(bist, cpu_init_detectedx);
#endif
#else
- #if USE_FALLBACK_IMAGE == 1
+ #if CONFIG_USE_FALLBACK_IMAGE == 1
failover_process(bist, cpu_init_detectedx);
#endif
real_main(bist, cpu_init_detectedx);
#endif
}
-#if USE_FAILOVER_IMAGE==0
+#if CONFIG_USE_FAILOVER_IMAGE==0
void real_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
#endif
};
- struct sys_info *sysinfo = (DCACHE_RAM_BASE + DCACHE_RAM_SIZE - DCACHE_RAM_GLOBAL_VAR_SIZE);
+ struct sys_info *sysinfo = (CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE);
int needs_reset = 0;
unsigned bsp_apicid = 0;
pnp_enter_ext_func_mode(SERIAL_DEV);
pnp_write_config(SERIAL_DEV, 0x24, 0);
- w83627ehg_enable_dev(SERIAL_DEV, TTYS0_BASE);
+ w83627ehg_enable_dev(SERIAL_DEV, CONFIG_TTYS0_BASE);
pnp_exit_ext_func_mode(SERIAL_DEV);
setup_mb_resource_map();
print_debug("bsp_apicid="); print_debug_hex8(bsp_apicid); print_debug("\r\n");
-#if MEM_TRAIN_SEQ == 1
+#if CONFIG_MEM_TRAIN_SEQ == 1
set_sysinfo_in_ram(0); // in BSP so could hold all ap until sysinfo is in ram
#endif
setup_coherent_ht_domain(); // routing table and start other core0
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
##
driver mainboard.o
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
#object reset.o
##
## Romcc output
##
makerule ./failover.E
- depends "$(MAINBOARD)/failover.c ../romcc"
- action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/failover.c ../romcc"
+ action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/failover.c ../romcc"
- action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/failover.c ../romcc"
+ action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/failover.c -o $@"
end
makerule ./auto.E
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -E -mcpu=p2 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -E -mcpu=p2 -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -mcpu=p2 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -mcpu=p2 -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
##
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_ROM_PAYLOAD
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_NRV2B
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses HAVE_MP_TABLE
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
-## ROM_SIZE is the size of boot ROM that this board will use.
-default ROM_SIZE = 256*1024
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
+default CONFIG_ROM_SIZE = 256*1024
###
### Build options
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## no MP table
##
-default HAVE_MP_TABLE=0
+default CONFIG_HAVE_MP_TABLE=0
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=0
+default CONFIG_HAVE_HARD_RESET=0
## Delay timer options
##
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=2
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=2
#object irq_tables.o
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=0
+default CONFIG_HAVE_OPTION_TABLE=0
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
-default FALLBACK_SIZE = 131072
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
+default CONFIG_FALLBACK_SIZE = 131072
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE=0x4000
+default CONFIG_HEAP_SIZE=0x4000
##
## Only use the option table in a normal image
##
-#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
+#default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
##
## The default compiler
##
-default CROSS_COMPILE=""
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CONFIG_CROSS_COMPILE=""
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## The Serial Console
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
#
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
##
driver mainboard.o
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
#object reset.o
##
## Romcc output
##
makerule ./failover.E
- depends "$(MAINBOARD)/failover.c ../romcc"
- action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/failover.c ../romcc"
+ action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/failover.c ../romcc"
- action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/failover.c ../romcc"
+ action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/failover.c -o $@"
end
makerule ./auto.E
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -E -mcpu=p2 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -E -mcpu=p2 -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -mcpu=p2 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -mcpu=p2 -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
##
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_ROM_PAYLOAD
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_NRV2B
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses HAVE_MP_TABLE
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
-## ROM_SIZE is the size of boot ROM that this board will use.
-default ROM_SIZE = 256*1024
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
+default CONFIG_ROM_SIZE = 256*1024
###
### Build options
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## no MP table
##
-default HAVE_MP_TABLE=0
+default CONFIG_HAVE_MP_TABLE=0
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=0
+default CONFIG_HAVE_HARD_RESET=0
## Delay timer options
##
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=2
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=2
#object irq_tables.o
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=0
+default CONFIG_HAVE_OPTION_TABLE=0
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
-default FALLBACK_SIZE = 131072
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
+default CONFIG_FALLBACK_SIZE = 131072
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE=0x4000
+default CONFIG_HEAP_SIZE=0x4000
##
## Only use the option table in a normal image
##
-#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
+#default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
##
## The default compiler
##
-default CROSS_COMPILE=""
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CONFIG_CROSS_COMPILE=""
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## The Serial Console
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
#
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
##
driver mainboard.o
-if HAVE_PIRQ_TABLE
+if CONFIG_HAVE_PIRQ_TABLE
object irq_tables.o
end
#compile cache_as_ram.c to auto.inc
makerule ./cache_as_ram_auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
# mainboardinit ./failover.inc
end
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_ROM_PAYLOAD
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_NRV2B
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses HAVE_MP_TABLE
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
uses CONFIG_VIDEO_MB
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
uses CONFIG_USE_PRINTK_IN_CAR
-uses PIRQ_ROUTE
+uses CONFIG_PIRQ_ROUTE
-## ROM_SIZE is the size of boot ROM that this board will use.
-default ROM_SIZE = 512*1024
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
+default CONFIG_ROM_SIZE = 512*1024
###
### Build options
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## no MP table
##
-default HAVE_MP_TABLE=0
+default CONFIG_HAVE_MP_TABLE=0
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=0
+default CONFIG_HAVE_HARD_RESET=0
## Delay timer options
##
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=5
-default PIRQ_ROUTE=1
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=5
+default CONFIG_PIRQ_ROUTE=1
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=0
+default CONFIG_HAVE_OPTION_TABLE=0
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
-default FALLBACK_SIZE = 131072
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
+default CONFIG_FALLBACK_SIZE = 131072
##
## enable CACHE_AS_RAM specifics
##
-default USE_DCACHE_RAM=1
-default DCACHE_RAM_BASE=0xc8000
-default DCACHE_RAM_SIZE=0x08000
+default CONFIG_USE_DCACHE_RAM=1
+default CONFIG_DCACHE_RAM_BASE=0xc8000
+default CONFIG_DCACHE_RAM_SIZE=0x08000
default CONFIG_USE_PRINTK_IN_CAR=1
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE=0x4000
+default CONFIG_HEAP_SIZE=0x4000
##
## Only use the option table in a normal image
##
-#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
+#default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
##
## The default compiler
##
-default CROSS_COMPILE=""
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CONFIG_CROSS_COMPILE=""
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## The Serial Console
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
#
* It is counting on some early MSR setup for the CS5536.
*/
cs5536_disable_internal_uart();
- w83627hf_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ w83627hf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
mb_gpio_init();
uart_init();
console_init();
const struct irq_routing_table intel_irq_routing_table = {
PIRQ_SIGNATURE,
PIRQ_VERSION,
- 32 + 16 * IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
+ 32 + 16 * CONFIG_IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
0x00, /* Where the interrupt router lies (bus) */
(0x0F << 3) | 0x0, /* Where the interrupt router lies (dev) */
0x00, /* IRQs devoted exclusively to PCI usage */
{0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0}, /* u8 rfu[11] */
0x00, /* Checksum */
{
- /* If you change the number of entries, change IRQ_SLOT_COUNT above! */
+ /* If you change the number of entries, change CONFIG_IRQ_SLOT_COUNT above! */
/* bus, dev|fn, {link, bitmap}, {link, bitmap}, {link, bitmap}, {link, bitmap}, slot, rfu */
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
arch i386 end
driver mainboard.o
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
# object reset.o
-if HAVE_ACPI_TABLES
+if CONFIG_HAVE_ACPI_TABLES
object fadt.o
object dsdt.o
object acpi_tables.o
end
makerule ./failover.E
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./auto.E
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -E -mcpu=p3 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -E -mcpu=p3 -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -mcpu=p3 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -mcpu=p3 -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
mainboardinit cpu/x86/16bit/entry16.inc
mainboardinit cpu/x86/32bit/entry32.inc
ldscript /cpu/x86/16bit/entry16.lds
ldscript /cpu/x86/32bit/entry32.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
mainboardinit arch/i386/lib/cpu_reset.inc
mainboardinit arch/i386/lib/id.inc
ldscript /arch/i386/lib/id.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
uses CONFIG_UDELAY_TSC
uses CONFIG_VIDEO_MB
-uses CROSS_COMPILE
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses FALLBACK_SIZE
-uses HAVE_ACPI_TABLES
-uses HAVE_ACPI_RESUME
-uses HAVE_FALLBACK_BOOT
-uses HAVE_MP_TABLE
-uses HAVE_OPTION_TABLE
-uses HAVE_PIRQ_TABLE
-uses HEAP_SIZE
-uses HOSTCC
-uses IRQ_SLOT_COUNT
+uses CONFIG_CROSS_COMPILE
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_HAVE_ACPI_TABLES
+uses CONFIG_HAVE_ACPI_RESUME
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_HOSTCC
+uses CONFIG_IRQ_SLOT_COUNT
uses COREBOOT_EXTRA_VERSION
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses OBJCOPY
-uses PAYLOAD_SIZE
-uses _RAMBASE
-uses _ROMBASE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
-uses ROM_SIZE
-uses STACK_SIZE
-uses TTYS0_BASE
-uses TTYS0_BAUD
-uses TTYS0_LCS
-uses USE_FALLBACK_IMAGE
-uses USE_OPTION_TABLE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_OBJCOPY
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_RAMBASE
+uses CONFIG_ROMBASE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
+uses CONFIG_ROM_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_LCS
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
-default ROM_SIZE = 512 * 1024
-default ROM_IMAGE_SIZE = 128 * 1024
-default HAVE_FALLBACK_BOOT = 1
-default FALLBACK_SIZE = 512 * 1024
+default CONFIG_ROM_SIZE = 512 * 1024
+default CONFIG_ROM_IMAGE_SIZE = 128 * 1024
+default CONFIG_HAVE_FALLBACK_BOOT = 1
+default CONFIG_FALLBACK_SIZE = 512 * 1024
default CONFIG_UDELAY_TSC = 1
default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 1
-default HAVE_PIRQ_TABLE = 1
-default IRQ_SLOT_COUNT = 7
-default HAVE_MP_TABLE = 0
-default HAVE_ACPI_TABLES = 0
+default CONFIG_HAVE_PIRQ_TABLE = 1
+default CONFIG_IRQ_SLOT_COUNT = 7
+default CONFIG_HAVE_MP_TABLE = 0
+default CONFIG_HAVE_ACPI_TABLES = 0
default CONFIG_IOAPIC = 0
-default HAVE_OPTION_TABLE = 0
+default CONFIG_HAVE_OPTION_TABLE = 0
default CONFIG_CONSOLE_VGA = 0
default CONFIG_PCI_ROM_RUN = 0
default CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0
default CONFIG_VIDEO_MB = 0
-default STACK_SIZE = 0x2000
-default HEAP_SIZE = 0x4000
-default _RAMBASE = 0x00004000
-default USE_OPTION_TABLE = 0
+default CONFIG_STACK_SIZE = 0x2000
+default CONFIG_HEAP_SIZE = 0x4000
+default CONFIG_RAMBASE = 0x00004000
+default CONFIG_USE_OPTION_TABLE = 0
default CONFIG_ROM_PAYLOAD = 1
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
default CONFIG_CONSOLE_SERIAL8250 = 1
-default TTYS0_BAUD = 115200
-default TTYS0_BASE = 0x3f8
-default TTYS0_LCS = 0x3 # 8n1
-default DEFAULT_CONSOLE_LOGLEVEL = 9
-default MAXIMUM_CONSOLE_LOGLEVEL = 9
-default MAINBOARD_VENDOR = "RCA"
-default MAINBOARD_PART_NUMBER = "RM4100"
+default CONFIG_TTYS0_BAUD = 115200
+default CONFIG_TTYS0_BASE = 0x3f8
+default CONFIG_TTYS0_LCS = 0x3 # 8n1
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
+default CONFIG_MAINBOARD_VENDOR = "RCA"
+default CONFIG_MAINBOARD_PART_NUMBER = "RM4100"
#
# CBFS
#
hard_reset();
}
- smscsuperio_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ smscsuperio_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
mb_gpio_init();
uart_init();
console_init();
const struct irq_routing_table intel_irq_routing_table = {
PIRQ_SIGNATURE, /* u32 signature */
PIRQ_VERSION, /* u16 version */
- 32+16*IRQ_SLOT_COUNT, /* there can be total 7 devices on the bus */
+ 32+16*CONFIG_IRQ_SLOT_COUNT, /* there can be total 7 devices on the bus */
0x00, /* Where the interrupt router lies (bus) */
(0x1f<<3)|0x0, /* Where the interrupt router lies (dev) */
0, /* IRQs devoted exclusively to PCI usage */
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
arch i386 end
driver mainboard.o
-if HAVE_PIRQ_TABLE
+if CONFIG_HAVE_PIRQ_TABLE
object irq_tables.o
end
makerule ./failover.E
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -E -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -E -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./auto.E
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -E -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -E -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
mainboardinit cpu/x86/16bit/entry16.inc
mainboardinit cpu/x86/32bit/entry32.inc
ldscript /cpu/x86/16bit/entry16.lds
ldscript /cpu/x86/32bit/entry32.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
mainboardinit arch/i386/lib/cpu_reset.inc
mainboardinit arch/i386/lib/id.inc
ldscript /arch/i386/lib/id.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_ROM_PAYLOAD
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses HAVE_MP_TABLE
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
-default ROM_SIZE = 256 * 1024
-default HAVE_FALLBACK_BOOT = 1
-default HAVE_MP_TABLE = 0
-default HAVE_HARD_RESET = 0
+default CONFIG_ROM_SIZE = 256 * 1024
+default CONFIG_HAVE_FALLBACK_BOOT = 1
+default CONFIG_HAVE_MP_TABLE = 0
+default CONFIG_HAVE_HARD_RESET = 0
default CONFIG_UDELAY_TSC = 1
default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 1
-default HAVE_PIRQ_TABLE = 1
-default IRQ_SLOT_COUNT = 0 # Override this in targets/*/Config.lb.
-default MAINBOARD_VENDOR = "N/A" # Override this in targets/*/Config.lb.
-default MAINBOARD_PART_NUMBER = "N/A" # Override this in targets/*/Config.lb.
-default ROM_IMAGE_SIZE = 64 * 1024
-default FALLBACK_SIZE = 128 * 1024
-default STACK_SIZE = 8 * 1024
-default HEAP_SIZE = 16 * 1024
-default HAVE_OPTION_TABLE = 0
-#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_HAVE_PIRQ_TABLE = 1
+default CONFIG_IRQ_SLOT_COUNT = 0 # Override this in targets/*/Config.lb.
+default CONFIG_MAINBOARD_VENDOR = "N/A" # Override this in targets/*/Config.lb.
+default CONFIG_MAINBOARD_PART_NUMBER = "N/A" # Override this in targets/*/Config.lb.
+default CONFIG_ROM_IMAGE_SIZE = 64 * 1024
+default CONFIG_FALLBACK_SIZE = 128 * 1024
+default CONFIG_STACK_SIZE = 8 * 1024
+default CONFIG_HEAP_SIZE = 16 * 1024
+default CONFIG_HAVE_OPTION_TABLE = 0
+#default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 0
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
-default CROSS_COMPILE = ""
-default CC = "$(CROSS_COMPILE)gcc -m32"
-default HOSTCC = "gcc"
+default CONFIG_CROSS_COMPILE = ""
+default CC = "$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC = "gcc"
default CONFIG_CONSOLE_SERIAL8250 = 1
-default TTYS0_BAUD = 115200
-default TTYS0_BASE = 0x3f8
-default TTYS0_LCS = 0x3 # 8n1
-default DEFAULT_CONSOLE_LOGLEVEL = 9
-default MAXIMUM_CONSOLE_LOGLEVEL = 9
+default CONFIG_TTYS0_BAUD = 115200
+default CONFIG_TTYS0_BASE = 0x3f8
+default CONFIG_TTYS0_LCS = 0x3 # 8n1
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
default CONFIG_CONSOLE_VGA = 1
default CONFIG_PCI_ROM_RUN = 1
default CONFIG_CBFS = 0
if (bist == 0)
early_mtrr_init();
- it8671f_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ it8671f_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
report_bist_failure(bist);
const struct irq_routing_table intel_irq_routing_table = {
PIRQ_SIGNATURE, /* u32 signature */
PIRQ_VERSION, /* u16 version */
- 32 + 16 * IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
+ 32 + 16 * CONFIG_IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
0x00, /* Interrupt router bus */
(0x07 << 3) | 0x0, /* Interrupt router dev */
0xc00, /* IRQs devoted exclusively to PCI usage */
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
default CONFIG_ROM_PAYLOAD = 1
#needed by irq_tables and mptable and acpi_tables
object get_bus_conf.o
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
#object reset.o
if CONFIG_USE_INIT
makerule ./auto.o
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
end
else
makerule ./auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
##
## Build our 16 bit and 32 bit coreboot entry code
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
end
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
##
## ROMSTRAP table for CK804
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit southbridge/nvidia/ck804/romstrap.inc
ldscript /southbridge/nvidia/ck804/romstrap.lds
end
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
end
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_MAX_CPUS
uses CONFIG_MAX_PHYSICAL_CPUS
uses CONFIG_LOGICAL_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
-uses _RAMBASE
+uses CONFIG_RAMBASE
uses CONFIG_GDB_STUB
-uses CROSS_COMPILE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_SERIAL8250
-uses HAVE_INIT_TIMER
+uses CONFIG_HAVE_INIT_TIMER
uses CONFIG_GDB_STUB
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
-uses HW_MEM_HOLE_SIZEK
-uses K8_HT_FREQ_1G_SUPPORT
+uses CONFIG_HW_MEM_HOLE_SIZEK
+uses CONFIG_K8_HT_FREQ_1G_SUPPORT
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
uses CONFIG_USE_INIT
uses CONFIG_USE_PRINTK_IN_CAR
-uses ENABLE_APIC_EXT_ID
-uses APIC_ID_OFFSET
-uses LIFT_BSP_APIC_ID
+uses CONFIG_ENABLE_APIC_EXT_ID
+uses CONFIG_APIC_ID_OFFSET
+uses CONFIG_LIFT_BSP_APIC_ID
-uses HT_CHAIN_UNITID_BASE
-uses HT_CHAIN_END_UNITID_BASE
-uses SB_HT_CHAIN_ON_BUS0
-uses SB_HT_CHAIN_UNITID_OFFSET_ONLY
+uses CONFIG_HT_CHAIN_UNITID_BASE
+uses CONFIG_HT_CHAIN_END_UNITID_BASE
+uses CONFIG_SB_HT_CHAIN_ON_BUS0
+uses CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY
-## ROM_SIZE is the size of boot ROM that this board will use.
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
#512K bytes
-#default ROM_SIZE=524288
+#default CONFIG_ROM_SIZE=524288
#1M bytes
-default ROM_SIZE=1048576
+default CONFIG_ROM_SIZE=1048576
##
-## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
+## CONFIG_FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
##
-#default FALLBACK_SIZE=131072
+#default CONFIG_FALLBACK_SIZE=131072
#256K
-default FALLBACK_SIZE=0x40000
+default CONFIG_FALLBACK_SIZE=0x40000
###
### Build options
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=11
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=11
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
##
## Move the default coreboot cmos range off of AMD RTC registers
##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
+default CONFIG_LB_CKS_RANGE_START=49
+default CONFIG_LB_CKS_RANGE_END=122
+default CONFIG_LB_CKS_LOC=123
##
## Build code for SMP support
default CONFIG_LOGICAL_CPUS=1
#1G memory hole
-default HW_MEM_HOLE_SIZEK=0x100000
+default CONFIG_HW_MEM_HOLE_SIZEK=0x100000
#Opteron K8 1G HT Support
-default K8_HT_FREQ_1G_SUPPORT=1
+default CONFIG_K8_HT_FREQ_1G_SUPPORT=1
##HT Unit ID offset, default is 1, the typical one
-default HT_CHAIN_UNITID_BASE=0x0
+default CONFIG_HT_CHAIN_UNITID_BASE=0x0
##real SB Unit ID, default is 0x20, mean dont touch it at last
-#default HT_CHAIN_END_UNITID_BASE=0x0
+#default CONFIG_HT_CHAIN_END_UNITID_BASE=0x0
#make the SB HT chain on bus 0, default is not (0)
-default SB_HT_CHAIN_ON_BUS0=2
+default CONFIG_SB_HT_CHAIN_ON_BUS0=2
##only offset for SB chain?, default is yes(1)
-default SB_HT_CHAIN_UNITID_OFFSET_ONLY=0
+default CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY=0
#VGA
default CONFIG_CONSOLE_VGA=1
##
## enable CACHE_AS_RAM specifics
##
-default USE_DCACHE_RAM=1
-default DCACHE_RAM_BASE=0xcf000
-default DCACHE_RAM_SIZE=0x1000
+default CONFIG_USE_DCACHE_RAM=1
+default CONFIG_DCACHE_RAM_BASE=0xcf000
+default CONFIG_DCACHE_RAM_SIZE=0x1000
default CONFIG_USE_INIT=0
-default ENABLE_APIC_EXT_ID=1
-default APIC_ID_OFFSET=0x10
-default LIFT_BSP_APIC_ID=0
+default CONFIG_ENABLE_APIC_EXT_ID=1
+default CONFIG_APIC_ID_OFFSET=0x10
+default CONFIG_LIFT_BSP_APIC_ID=0
##
##
## Clean up the motherboard id strings
##
-default MAINBOARD_PART_NUMBER="ultra40"
-default MAINBOARD_VENDOR="sunw"
+default CONFIG_MAINBOARD_PART_NUMBER="ultra40"
+default CONFIG_MAINBOARD_VENDOR="sunw"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x108e
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x40
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x108e
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x40
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE=0x4000
+default CONFIG_HEAP_SIZE=0x4000
##
## Only use the option table in a normal image
##
-default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
##
## Coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00004000
+default CONFIG_RAMBASE=0x00004000
##
## Load the payload from the ROM
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## Disable the gdb stub by default
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
### End Options.lb
#
#include "cpu/amd/model_fxx/init_cpus.c"
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
#include "southbridge/nvidia/ck804/ck804_enable_rom.c"
#include "northbridge/amd/amdk8/early_ht.c"
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
failover_process(bist, cpu_init_detectedx);
#endif
real_main(bist, cpu_init_detectedx);
bsp_apicid = init_cpus(cpu_init_detectedx);
}
- lpc47b397_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ lpc47b397_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/failovercalculation.lb
arch i386 end
#needed by irq_tables and mptable and acpi_tables
object get_bus_conf.o
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
#object reset.o
if CONFIG_USE_INIT
makerule ./auto.o
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
end
else
makerule ./auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
end
-if USE_FAILOVER_IMAGE
+if CONFIG_USE_FAILOVER_IMAGE
else
if CONFIG_AP_CODE_IN_CAR
makerule ./apc_auto.o
- depends "$(MAINBOARD)/apc_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/apc_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/apc_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/apc_auto.c -o $@"
end
ldscript /arch/i386/init/ldscript_apc.lb
end
##
## Build our 16 bit and 32 bit coreboot entry code
##
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
end
##
## Build our reset vector (This is where coreboot is entered)
##
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
ldscript /cpu/x86/32bit/reset32.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
##
## ROMSTRAP table for MCP55
##
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
mainboardinit southbridge/nvidia/mcp55/romstrap.inc
ldscript /southbridge/nvidia/mcp55/romstrap.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
mainboardinit southbridge/nvidia/mcp55/romstrap.inc
ldscript /southbridge/nvidia/mcp55/romstrap.lds
end
### Things are delicate and we test to see if we should
### failover to another image.
###
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
ldscript /arch/i386/lib/failover_failover.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
end
end
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses HAVE_ACPI_TABLES
-uses HAVE_ACPI_RESUME
-uses ACPI_SSDTX_NUM
-uses USE_FALLBACK_IMAGE
-uses USE_FAILOVER_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_FAILOVER_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_HAVE_ACPI_TABLES
+uses CONFIG_HAVE_ACPI_RESUME
+uses CONFIG_ACPI_SSDTX_NUM
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_USE_FAILOVER_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_FAILOVER_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_MAX_CPUS
uses CONFIG_MAX_PHYSICAL_CPUS
uses CONFIG_LOGICAL_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses FAILOVER_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_FAILOVER_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_NRV2B
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses HAVE_LOW_TABLES
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_HAVE_LOW_TABLES
uses CONFIG_MULTIBOOT
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
-uses _RAMBASE
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_RAMBASE
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_SERIAL8250
-uses HAVE_INIT_TIMER
+uses CONFIG_HAVE_INIT_TIMER
uses CONFIG_GDB_STUB
uses CONFIG_GDB_STUB
-uses CROSS_COMPILE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
-uses HW_MEM_HOLE_SIZEK
-uses HW_MEM_HOLE_SIZE_AUTO_INC
-uses K8_HT_FREQ_1G_SUPPORT
-
-uses HT_CHAIN_UNITID_BASE
-uses HT_CHAIN_END_UNITID_BASE
-uses SB_HT_CHAIN_ON_BUS0
-uses SB_HT_CHAIN_UNITID_OFFSET_ONLY
-
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
-uses DCACHE_RAM_GLOBAL_VAR_SIZE
+uses CONFIG_HW_MEM_HOLE_SIZEK
+uses CONFIG_HW_MEM_HOLE_SIZE_AUTO_INC
+uses CONFIG_K8_HT_FREQ_1G_SUPPORT
+
+uses CONFIG_HT_CHAIN_UNITID_BASE
+uses CONFIG_HT_CHAIN_END_UNITID_BASE
+uses CONFIG_SB_HT_CHAIN_ON_BUS0
+uses CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY
+
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
+uses CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE
uses CONFIG_USE_INIT
-uses SERIAL_CPU_INIT
+uses CONFIG_SERIAL_CPU_INIT
-uses ENABLE_APIC_EXT_ID
-uses APIC_ID_OFFSET
-uses LIFT_BSP_APIC_ID
+uses CONFIG_ENABLE_APIC_EXT_ID
+uses CONFIG_APIC_ID_OFFSET
+uses CONFIG_LIFT_BSP_APIC_ID
uses CONFIG_PCI_64BIT_PREF_MEM
uses CONFIG_AP_CODE_IN_CAR
-uses MEM_TRAIN_SEQ
+uses CONFIG_MEM_TRAIN_SEQ
-uses WAIT_BEFORE_CPUS_INIT
+uses CONFIG_WAIT_BEFORE_CPUS_INIT
uses CONFIG_USE_PRINTK_IN_CAR
###
##
-## ROM_SIZE is the size of boot ROM that this board will use.
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
##
-#default ROM_SIZE=524288
-default ROM_SIZE=0x100000
+#default CONFIG_ROM_SIZE=524288
+default CONFIG_ROM_SIZE=0x100000
-default HAVE_LOW_TABLES = 0
+default CONFIG_HAVE_LOW_TABLES = 0
default CONFIG_MULTIBOOT=0
##
-## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
+## CONFIG_FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
##
-#default FALLBACK_SIZE=131072
-#default FALLBACK_SIZE=0x40000
+#default CONFIG_FALLBACK_SIZE=131072
+#default CONFIG_FALLBACK_SIZE=0x40000
#FALLBACK: 256K-4K
-default FALLBACK_SIZE=0x3f000
+default CONFIG_FALLBACK_SIZE=0x3f000
#FAILOVER: 4K
-default FAILOVER_SIZE=0x01000
+default CONFIG_FAILOVER_SIZE=0x01000
#more 1M for pgtbl
default CONFIG_LB_MEM_TOPK=2048
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
-default HAVE_FAILOVER_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FAILOVER_BOOT=1
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=11
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=11
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
## ACPI tables will be included
-default HAVE_ACPI_TABLES=0
+default CONFIG_HAVE_ACPI_TABLES=0
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
##
## Move the default coreboot cmos range off of AMD RTC registers
##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
+default CONFIG_LB_CKS_RANGE_START=49
+default CONFIG_LB_CKS_RANGE_END=122
+default CONFIG_LB_CKS_LOC=123
##
## Build code for SMP support
default CONFIG_MAX_PHYSICAL_CPUS=2
default CONFIG_LOGICAL_CPUS=1
-default SERIAL_CPU_INIT=0
+default CONFIG_SERIAL_CPU_INIT=0
-default ENABLE_APIC_EXT_ID=0
-default APIC_ID_OFFSET=0x10
-default LIFT_BSP_APIC_ID=1
+default CONFIG_ENABLE_APIC_EXT_ID=0
+default CONFIG_APIC_ID_OFFSET=0x10
+default CONFIG_LIFT_BSP_APIC_ID=1
#memory hole size, 0 mean disable, others will enable the hole, at that case if it is small than mmio_basek, it will use mmio_basek instead.
#2G
-#default HW_MEM_HOLE_SIZEK=0x200000
+#default CONFIG_HW_MEM_HOLE_SIZEK=0x200000
#1G
-default HW_MEM_HOLE_SIZEK=0x100000
+default CONFIG_HW_MEM_HOLE_SIZEK=0x100000
#512M
-#default HW_MEM_HOLE_SIZEK=0x80000
+#default CONFIG_HW_MEM_HOLE_SIZEK=0x80000
#make auto increase hole size to avoid hole_startk equal to basek so as to make some kernel happy
-#default HW_MEM_HOLE_SIZE_AUTO_INC=1
+#default CONFIG_HW_MEM_HOLE_SIZE_AUTO_INC=1
#Opteron K8 1G HT Support
-default K8_HT_FREQ_1G_SUPPORT=1
+default CONFIG_K8_HT_FREQ_1G_SUPPORT=1
#VGA Console
default CONFIG_CONSOLE_VGA=1
default CONFIG_PCI_ROM_RUN=1
#HT Unit ID offset, default is 1, the typical one, 0 mean only one HT device
-default HT_CHAIN_UNITID_BASE=0
+default CONFIG_HT_CHAIN_UNITID_BASE=0
#real SB Unit ID, default is 0x20, mean dont touch it at last
-#default HT_CHAIN_END_UNITID_BASE=0x6
+#default CONFIG_HT_CHAIN_END_UNITID_BASE=0x6
#make the SB HT chain on bus 0, default is not (0)
-default SB_HT_CHAIN_ON_BUS0=2
+default CONFIG_SB_HT_CHAIN_ON_BUS0=2
#only offset for SB chain?, default is yes(1)
-default SB_HT_CHAIN_UNITID_OFFSET_ONLY=0
+default CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY=0
#allow capable device use that above 4G
#default CONFIG_PCI_64BIT_PREF_MEM=1
##
## enable CACHE_AS_RAM specifics
##
-default USE_DCACHE_RAM=1
-default DCACHE_RAM_BASE=0xc8000
-default DCACHE_RAM_SIZE=0x08000
-default DCACHE_RAM_GLOBAL_VAR_SIZE=0x01000
+default CONFIG_USE_DCACHE_RAM=1
+default CONFIG_DCACHE_RAM_BASE=0xc8000
+default CONFIG_DCACHE_RAM_SIZE=0x08000
+default CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE=0x01000
default CONFIG_USE_INIT=0
default CONFIG_AP_CODE_IN_CAR=1
-default MEM_TRAIN_SEQ=1
-default WAIT_BEFORE_CPUS_INIT=1
+default CONFIG_MEM_TRAIN_SEQ=1
+default CONFIG_WAIT_BEFORE_CPUS_INIT=1
##
## Build code to setup a generic IOAPIC
##
## Clean up the motherboard id strings
##
-default MAINBOARD_PART_NUMBER="h8dme"
-default MAINBOARD_VENDOR="Supermicro"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x15d9
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x1511
+default CONFIG_MAINBOARD_PART_NUMBER="h8dme"
+default CONFIG_MAINBOARD_VENDOR="Supermicro"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x15d9
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x1511
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 32K heap
##
-default HEAP_SIZE=0x8000
+default CONFIG_HEAP_SIZE=0x8000
##
## Only use the option table in a normal image
##
-default USE_OPTION_TABLE = (!USE_FALLBACK_IMAGE) && (!USE_FAILOVER_IMAGE )
+default CONFIG_USE_OPTION_TABLE = (!CONFIG_USE_FALLBACK_IMAGE) && (!CONFIG_USE_FAILOVER_IMAGE )
##
## Coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00100000
+default CONFIG_RAMBASE=0x00100000
##
## Load the payload from the ROM
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## Disable the gdb stub by default
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=9
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=9
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=9
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=9
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
### End Options.lb
#
void hardwaremain(int ret_addr)
{
- struct sys_info *sysinfo = (DCACHE_RAM_BASE + DCACHE_RAM_SIZE - DCACHE_RAM_GLOBAL_VAR_SIZE); // in CACHE
- struct sys_info *sysinfox = ((CONFIG_LB_MEM_TOPK<<10) - DCACHE_RAM_GLOBAL_VAR_SIZE); // in RAM
+ struct sys_info *sysinfo = (CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE); // in CACHE
+ struct sys_info *sysinfox = ((CONFIG_LB_MEM_TOPK<<10) - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE); // in RAM
struct node_core_id id;
//if we want to wait for core1 done before DQS training, set it to 0
#define K8_SET_FIDVID_CORE0_ONLY 1
-#if K8_REV_F_SUPPORT == 1
+#if CONFIG_K8_REV_F_SUPPORT == 1
#define K8_REV_F_SUPPORT_F0_F1_WORKAROUND 0
#endif
// for enable the FAN
#include "southbridge/nvidia/mcp55/mcp55_early_smbus.c"
-#if USE_FAILOVER_IMAGE==0
+#if CONFIG_USE_FAILOVER_IMAGE==0
#include "pc80/serial.c"
#include "arch/i386/lib/console.c"
#include "ram/ramtest.c"
#include "superio/winbond/w83627hf/w83627hf_early_serial.c"
#include "superio/winbond/w83627hf/w83627hf_early_init.c"
-#if USE_FAILOVER_IMAGE==0
+#if CONFIG_USE_FAILOVER_IMAGE==0
#include "cpu/x86/bist.h"
#endif
-#if ((HAVE_FAILOVER_BOOT==1) && (USE_FAILOVER_IMAGE == 1)) || ((HAVE_FAILOVER_BOOT==0) && (USE_FALLBACK_IMAGE == 1))
+#if ((CONFIG_HAVE_FAILOVER_BOOT==1) && (CONFIG_USE_FAILOVER_IMAGE == 1)) || ((CONFIG_HAVE_FAILOVER_BOOT==0) && (CONFIG_USE_FALLBACK_IMAGE == 1))
#include "southbridge/nvidia/mcp55/mcp55_enable_rom.c"
#include "northbridge/amd/amdk8/early_ht.c"
);
fallback_image:
-#if HAVE_FAILOVER_BOOT==1
+#if CONFIG_HAVE_FAILOVER_BOOT==1
__asm__ volatile ("jmp __fallback_image": /* outputs */
:"a" (bist), "b"(cpu_init_detectedx) /* inputs */
)
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
-#if HAVE_FAILOVER_BOOT==1
-#if USE_FAILOVER_IMAGE==1
+#if CONFIG_HAVE_FAILOVER_BOOT==1
+#if CONFIG_USE_FAILOVER_IMAGE==1
failover_process(bist, cpu_init_detectedx);
#else
real_main(bist, cpu_init_detectedx);
#endif
#else
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
failover_process(bist, cpu_init_detectedx);
#endif
real_main(bist, cpu_init_detectedx);
#define RC0 (2<<8)
#define RC1 (1<<8)
-#if USE_FAILOVER_IMAGE==0
+#if CONFIG_USE_FAILOVER_IMAGE==0
void real_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
};
struct sys_info *sysinfo =
- (DCACHE_RAM_BASE + DCACHE_RAM_SIZE - DCACHE_RAM_GLOBAL_VAR_SIZE);
+ (CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE);
int needs_reset = 0;
unsigned bsp_apicid = 0;
pnp_enter_ext_func_mode(SERIAL_DEV);
pnp_write_config(SERIAL_DEV, 0x24, 0x84 | (1 << 6));
- w83627hf_enable_dev(SERIAL_DEV, TTYS0_BASE);
+ w83627hf_enable_dev(SERIAL_DEV, CONFIG_TTYS0_BASE);
pnp_exit_ext_func_mode(SERIAL_DEV);
uart_init();
print_debug_hex8(bsp_apicid);
print_debug("\r\n");
-#if MEM_TRAIN_SEQ == 1
+#if CONFIG_MEM_TRAIN_SEQ == 1
set_sysinfo_in_ram(0); // in BSP so could hold all ap until sysinfo is in ram
#endif
/* dump_smbus_registers(); */
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/failovercalculation.lb
arch i386 end
#needed by irq_tables and mptable and acpi_tables
object get_bus_conf.o
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
#object reset.o
if CONFIG_USE_INIT
makerule ./auto.o
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
end
else
makerule ./auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
end
-if USE_FAILOVER_IMAGE
+if CONFIG_USE_FAILOVER_IMAGE
else
if CONFIG_AP_CODE_IN_CAR
makerule ./apc_auto.o
- depends "$(MAINBOARD)/apc_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/apc_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/apc_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/apc_auto.c -o $@"
end
ldscript /arch/i386/init/ldscript_apc.lb
end
##
## Build our 16 bit and 32 bit coreboot entry code
##
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
end
##
## Build our reset vector (This is where coreboot is entered)
##
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
ldscript /cpu/x86/32bit/reset32.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
##
## ROMSTRAP table for MCP55
##
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
mainboardinit southbridge/nvidia/mcp55/romstrap.inc
ldscript /southbridge/nvidia/mcp55/romstrap.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
mainboardinit southbridge/nvidia/mcp55/romstrap.inc
ldscript /southbridge/nvidia/mcp55/romstrap.lds
end
### Things are delicate and we test to see if we should
### failover to another image.
###
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
ldscript /arch/i386/lib/failover_failover.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
end
end
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses HAVE_ACPI_TABLES
-uses HAVE_ACPI_RESUME
-uses ACPI_SSDTX_NUM
-uses USE_FALLBACK_IMAGE
-uses USE_FAILOVER_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_FAILOVER_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_HAVE_ACPI_TABLES
+uses CONFIG_HAVE_ACPI_RESUME
+uses CONFIG_ACPI_SSDTX_NUM
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_USE_FAILOVER_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_FAILOVER_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_MAX_CPUS
uses CONFIG_MAX_PHYSICAL_CPUS
uses CONFIG_LOGICAL_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses FAILOVER_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_FAILOVER_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_NRV2B
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
-uses _RAMBASE
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_RAMBASE
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_SERIAL8250
-uses HAVE_INIT_TIMER
+uses CONFIG_HAVE_INIT_TIMER
uses CONFIG_GDB_STUB
uses CONFIG_GDB_STUB
-uses CROSS_COMPILE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
-uses HW_MEM_HOLE_SIZEK
-uses HW_MEM_HOLE_SIZE_AUTO_INC
-uses K8_HT_FREQ_1G_SUPPORT
-
-uses HT_CHAIN_UNITID_BASE
-uses HT_CHAIN_END_UNITID_BASE
-uses SB_HT_CHAIN_ON_BUS0
-uses SB_HT_CHAIN_UNITID_OFFSET_ONLY
-
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
-uses DCACHE_RAM_GLOBAL_VAR_SIZE
+uses CONFIG_HW_MEM_HOLE_SIZEK
+uses CONFIG_HW_MEM_HOLE_SIZE_AUTO_INC
+uses CONFIG_K8_HT_FREQ_1G_SUPPORT
+
+uses CONFIG_HT_CHAIN_UNITID_BASE
+uses CONFIG_HT_CHAIN_END_UNITID_BASE
+uses CONFIG_SB_HT_CHAIN_ON_BUS0
+uses CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY
+
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
+uses CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE
uses CONFIG_USE_INIT
-uses SERIAL_CPU_INIT
+uses CONFIG_SERIAL_CPU_INIT
-uses ENABLE_APIC_EXT_ID
-uses APIC_ID_OFFSET
-uses LIFT_BSP_APIC_ID
+uses CONFIG_ENABLE_APIC_EXT_ID
+uses CONFIG_APIC_ID_OFFSET
+uses CONFIG_LIFT_BSP_APIC_ID
uses CONFIG_PCI_64BIT_PREF_MEM
uses CONFIG_AP_CODE_IN_CAR
-uses MEM_TRAIN_SEQ
+uses CONFIG_MEM_TRAIN_SEQ
-uses WAIT_BEFORE_CPUS_INIT
+uses CONFIG_WAIT_BEFORE_CPUS_INIT
uses CONFIG_USE_PRINTK_IN_CAR
###
##
-## ROM_SIZE is the size of boot ROM that this board will use.
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
##
-#default ROM_SIZE=524288
-default ROM_SIZE=0x100000
+#default CONFIG_ROM_SIZE=524288
+default CONFIG_ROM_SIZE=0x100000
##
-## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
+## CONFIG_FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
##
-#default FALLBACK_SIZE=131072
-#default FALLBACK_SIZE=0x40000
+#default CONFIG_FALLBACK_SIZE=131072
+#default CONFIG_FALLBACK_SIZE=0x40000
#FALLBACK: 256K-4K
-default FALLBACK_SIZE=0x3f000
+default CONFIG_FALLBACK_SIZE=0x3f000
#FAILOVER: 4K
-default FAILOVER_SIZE=0x01000
+default CONFIG_FAILOVER_SIZE=0x01000
#more 1M for pgtbl
default CONFIG_LB_MEM_TOPK=2048
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
-default HAVE_FAILOVER_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FAILOVER_BOOT=1
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=11
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=11
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
## ACPI tables will be included
-default HAVE_ACPI_TABLES=0
+default CONFIG_HAVE_ACPI_TABLES=0
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
##
## Move the default coreboot cmos range off of AMD RTC registers
##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
+default CONFIG_LB_CKS_RANGE_START=49
+default CONFIG_LB_CKS_RANGE_END=122
+default CONFIG_LB_CKS_LOC=123
##
## Build code for SMP support
default CONFIG_MAX_PHYSICAL_CPUS=2
default CONFIG_LOGICAL_CPUS=1
-default SERIAL_CPU_INIT=0
+default CONFIG_SERIAL_CPU_INIT=0
-default ENABLE_APIC_EXT_ID=0
-default APIC_ID_OFFSET=0x10
-default LIFT_BSP_APIC_ID=1
+default CONFIG_ENABLE_APIC_EXT_ID=0
+default CONFIG_APIC_ID_OFFSET=0x10
+default CONFIG_LIFT_BSP_APIC_ID=1
#memory hole size, 0 mean disable, others will enable the hole, at that case if it is small than mmio_basek, it will use mmio_basek instead.
#2G
-#default HW_MEM_HOLE_SIZEK=0x200000
+#default CONFIG_HW_MEM_HOLE_SIZEK=0x200000
#1G
-default HW_MEM_HOLE_SIZEK=0x100000
+default CONFIG_HW_MEM_HOLE_SIZEK=0x100000
#512M
-#default HW_MEM_HOLE_SIZEK=0x80000
+#default CONFIG_HW_MEM_HOLE_SIZEK=0x80000
#make auto increase hole size to avoid hole_startk equal to basek so as to make some kernel happy
-#default HW_MEM_HOLE_SIZE_AUTO_INC=1
+#default CONFIG_HW_MEM_HOLE_SIZE_AUTO_INC=1
#Opteron K8 1G HT Support
-default K8_HT_FREQ_1G_SUPPORT=1
+default CONFIG_K8_HT_FREQ_1G_SUPPORT=1
#VGA Console
default CONFIG_CONSOLE_VGA=1
default CONFIG_PCI_ROM_RUN=1
#HT Unit ID offset, default is 1, the typical one, 0 mean only one HT device
-default HT_CHAIN_UNITID_BASE=0
+default CONFIG_HT_CHAIN_UNITID_BASE=0
#real SB Unit ID, default is 0x20, mean dont touch it at last
-#default HT_CHAIN_END_UNITID_BASE=0x6
+#default CONFIG_HT_CHAIN_END_UNITID_BASE=0x6
#make the SB HT chain on bus 0, default is not (0)
-default SB_HT_CHAIN_ON_BUS0=2
+default CONFIG_SB_HT_CHAIN_ON_BUS0=2
#only offset for SB chain?, default is yes(1)
-default SB_HT_CHAIN_UNITID_OFFSET_ONLY=0
+default CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY=0
#allow capable device use that above 4G
#default CONFIG_PCI_64BIT_PREF_MEM=1
##
## enable CACHE_AS_RAM specifics
##
-default USE_DCACHE_RAM=1
-default DCACHE_RAM_BASE=0xc8000
-default DCACHE_RAM_SIZE=0x08000
-default DCACHE_RAM_GLOBAL_VAR_SIZE=0x01000
+default CONFIG_USE_DCACHE_RAM=1
+default CONFIG_DCACHE_RAM_BASE=0xc8000
+default CONFIG_DCACHE_RAM_SIZE=0x08000
+default CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE=0x01000
default CONFIG_USE_INIT=0
default CONFIG_AP_CODE_IN_CAR=1
-default MEM_TRAIN_SEQ=1
-default WAIT_BEFORE_CPUS_INIT=1
+default CONFIG_MEM_TRAIN_SEQ=1
+default CONFIG_WAIT_BEFORE_CPUS_INIT=1
##
## Build code to setup a generic IOAPIC
##
## Clean up the motherboard id strings
##
-default MAINBOARD_PART_NUMBER="h8dmr"
-default MAINBOARD_VENDOR="Supermicro"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x15d9
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x1511
+default CONFIG_MAINBOARD_PART_NUMBER="h8dmr"
+default CONFIG_MAINBOARD_VENDOR="Supermicro"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x15d9
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x1511
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 32K heap
##
-default HEAP_SIZE=0x8000
+default CONFIG_HEAP_SIZE=0x8000
##
## Only use the option table in a normal image
##
-default USE_OPTION_TABLE = (!USE_FALLBACK_IMAGE) && (!USE_FAILOVER_IMAGE )
+default CONFIG_USE_OPTION_TABLE = (!CONFIG_USE_FALLBACK_IMAGE) && (!CONFIG_USE_FAILOVER_IMAGE )
##
## Coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00100000
+default CONFIG_RAMBASE=0x00100000
##
## Load the payload from the ROM
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## Disable the gdb stub by default
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
### End Options.lb
#
void hardwaremain(int ret_addr)
{
- struct sys_info *sysinfo = (DCACHE_RAM_BASE + DCACHE_RAM_SIZE - DCACHE_RAM_GLOBAL_VAR_SIZE); // in CACHE
- struct sys_info *sysinfox = ((CONFIG_LB_MEM_TOPK<<10) - DCACHE_RAM_GLOBAL_VAR_SIZE); // in RAM
+ struct sys_info *sysinfo = (CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE); // in CACHE
+ struct sys_info *sysinfox = ((CONFIG_LB_MEM_TOPK<<10) - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE); // in RAM
struct node_core_id id;
//if we want to wait for core1 done before DQS training, set it to 0
#define K8_SET_FIDVID_CORE0_ONLY 1
-#if K8_REV_F_SUPPORT == 1
+#if CONFIG_K8_REV_F_SUPPORT == 1
#define K8_REV_F_SUPPORT_F0_F1_WORKAROUND 0
#endif
// for enable the FAN
#include "southbridge/nvidia/mcp55/mcp55_early_smbus.c"
-#if USE_FAILOVER_IMAGE==0
+#if CONFIG_USE_FAILOVER_IMAGE==0
#include "pc80/serial.c"
#include "arch/i386/lib/console.c"
#include "ram/ramtest.c"
#include "superio/winbond/w83627hf/w83627hf_early_serial.c"
#include "superio/winbond/w83627hf/w83627hf_early_init.c"
-#if USE_FAILOVER_IMAGE==0
+#if CONFIG_USE_FAILOVER_IMAGE==0
#include "cpu/x86/bist.h"
#endif
-#if ((HAVE_FAILOVER_BOOT==1) && (USE_FAILOVER_IMAGE == 1)) || ((HAVE_FAILOVER_BOOT==0) && (USE_FALLBACK_IMAGE == 1))
+#if ((CONFIG_HAVE_FAILOVER_BOOT==1) && (CONFIG_USE_FAILOVER_IMAGE == 1)) || ((CONFIG_HAVE_FAILOVER_BOOT==0) && (CONFIG_USE_FALLBACK_IMAGE == 1))
#include "southbridge/nvidia/mcp55/mcp55_enable_rom.c"
#include "northbridge/amd/amdk8/early_ht.c"
);
fallback_image:
-#if HAVE_FAILOVER_BOOT==1
+#if CONFIG_HAVE_FAILOVER_BOOT==1
__asm__ volatile ("jmp __fallback_image"
: /* outputs */
: "a" (bist), "b" (cpu_init_detectedx) /* inputs */
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
-#if HAVE_FAILOVER_BOOT==1
- #if USE_FAILOVER_IMAGE==1
+#if CONFIG_HAVE_FAILOVER_BOOT==1
+ #if CONFIG_USE_FAILOVER_IMAGE==1
failover_process(bist, cpu_init_detectedx);
#else
real_main(bist, cpu_init_detectedx);
#endif
#else
- #if USE_FALLBACK_IMAGE == 1
+ #if CONFIG_USE_FALLBACK_IMAGE == 1
failover_process(bist, cpu_init_detectedx);
#endif
real_main(bist, cpu_init_detectedx);
#endif
}
-#if USE_FAILOVER_IMAGE==0
+#if CONFIG_USE_FAILOVER_IMAGE==0
void real_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
#endif
};
- struct sys_info *sysinfo = (DCACHE_RAM_BASE + DCACHE_RAM_SIZE - DCACHE_RAM_GLOBAL_VAR_SIZE);
+ struct sys_info *sysinfo = (CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE);
int needs_reset = 0;
unsigned bsp_apicid = 0;
pnp_enter_ext_func_mode(SERIAL_DEV);
pnp_write_config(SERIAL_DEV, 0x24, 0x84 | (1 << 6));
- w83627hf_enable_dev(SERIAL_DEV, TTYS0_BASE);
+ w83627hf_enable_dev(SERIAL_DEV, CONFIG_TTYS0_BASE);
pnp_exit_ext_func_mode(SERIAL_DEV);
uart_init();
print_debug("bsp_apicid="); print_debug_hex8(bsp_apicid); print_debug("\r\n");
-#if MEM_TRAIN_SEQ == 1
+#if CONFIG_MEM_TRAIN_SEQ == 1
set_sysinfo_in_ram(0); // in BSP so could hold all ap until sysinfo is in ram
#endif
setup_coherent_ht_domain(); // routing table and start other core0
##
## Only use the option table in a normal image
##
-default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 128 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 128 * 1024
include /config/nofailovercalculation.lb
##
##
driver mainboard.o
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
object reset.o
##
## Romcc output
##
makerule ./failover.E
- depends "$(MAINBOARD)/failover.c ../romcc"
- action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/failover.c ../romcc"
+ action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/failover.c ../romcc"
- action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/failover.c ../romcc"
+ action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/failover.c -o $@"
end
makerule ./auto.E
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -E -mcpu=p4 -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -E -mcpu=p4 -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -mcpu=p4 -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -mcpu=p4 -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
##
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_LOGICAL_CPUS
uses CONFIG_MAX_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
-uses _RAMBASE
+uses CONFIG_RAMBASE
uses CONFIG_GDB_STUB
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_BTEXT
uses CC
-uses HOSTCC
-uses CROSS_COMPILE
-uses OBJCOPY
+uses CONFIG_HOSTCC
+uses CONFIG_CROSS_COMPILE
+uses CONFIG_OBJCOPY
###
###
##
-## ROM_SIZE is the size of boot ROM that this board will use.
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
##
-default ROM_SIZE=1048576
+default CONFIG_ROM_SIZE=1048576
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## Delay timer options
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=16
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=16
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
##
## Move the default coreboot cmos range off of AMD RTC registers
##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
+default CONFIG_LB_CKS_RANGE_START=49
+default CONFIG_LB_CKS_RANGE_END=122
+default CONFIG_LB_CKS_LOC=123
##
## Build code for SMP support
##
## Clean up the motherboard id strings
##
-default MAINBOARD_PART_NUMBER="X6DAI"
-default MAINBOARD_VENDOR= "Supermicro"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x15D9
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x6780
+default CONFIG_MAINBOARD_PART_NUMBER="X6DAI"
+default CONFIG_MAINBOARD_VENDOR= "Supermicro"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x15D9
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x6780
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 32K heap
##
-default HEAP_SIZE=0x8000
+default CONFIG_HEAP_SIZE=0x8000
###
### Compute the location and size of where this firmware image
### (coreboot plus bootloader) will live in the boot rom chip.
###
-default FALLBACK_SIZE=131072
+default CONFIG_FALLBACK_SIZE=131072
##
## Coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00004000
+default CONFIG_RAMBASE=0x00004000
##
## Load the payload from the ROM
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## Disable the gdb stub by default
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
##
## Don't enable the btext console
outb(0x87,0x2e);
outb(0x87,0x2e);
pnp_write_config(CONSOLE_SERIAL_DEV, 0x24, 0x84 | (1 << 6));
- w83627hf_enable_dev(CONSOLE_SERIAL_DEV, TTYS0_BASE);
+ w83627hf_enable_dev(CONSOLE_SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
##
## Only use the option table in a normal image
##
-default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 128 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 128 * 1024
include /config/nofailovercalculation.lb
## Set all of the defaults for an x86 architecture
##
driver mainboard.o
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
object reset.o
##
## Romcc output
##
makerule ./failover.E
- depends "$(MAINBOARD)/failover.c ../romcc"
- action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/failover.c ../romcc"
+ action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/failover.c ../romcc"
- action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/failover.c ../romcc"
+ action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/failover.c -o $@"
end
makerule ./auto.E
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -E -mcpu=p4 -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -E -mcpu=p4 -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -mcpu=p4 -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -mcpu=p4 -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
##
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_LOGICAL_CPUS
uses CONFIG_MAX_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
-uses _RAMBASE
+uses CONFIG_RAMBASE
uses CONFIG_GDB_STUB
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_BTEXT
uses CC
-uses HOSTCC
-uses CROSS_COMPILE
-uses OBJCOPY
+uses CONFIG_HOSTCC
+uses CONFIG_CROSS_COMPILE
+uses CONFIG_OBJCOPY
###
###
##
-## ROM_SIZE is the size of boot ROM that this board will use.
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
##
-default ROM_SIZE=1048576
+default CONFIG_ROM_SIZE=1048576
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## Delay timer options
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=16
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=16
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
##
## Move the default coreboot cmos range off of AMD RTC registers
##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
+default CONFIG_LB_CKS_RANGE_START=49
+default CONFIG_LB_CKS_RANGE_END=122
+default CONFIG_LB_CKS_LOC=123
##
## Build code for SMP support
##
## Clean up the motherboard id strings
##
-default MAINBOARD_PART_NUMBER="X6DHE_g"
-default MAINBOARD_VENDOR= "Supermicro"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x15D9
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x6080
+default CONFIG_MAINBOARD_PART_NUMBER="X6DHE_g"
+default CONFIG_MAINBOARD_VENDOR= "Supermicro"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x15D9
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x6080
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 32K heap
##
-default HEAP_SIZE=0x8000
+default CONFIG_HEAP_SIZE=0x8000
###
### Compute the location and size of where this firmware image
### (coreboot plus bootloader) will live in the boot rom chip.
###
-default FALLBACK_SIZE=131072
+default CONFIG_FALLBACK_SIZE=131072
##
## Coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00004000
+default CONFIG_RAMBASE=0x00004000
##
## Load the payload from the ROM
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## Disable the gdb stub by default
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
##
## Don't enable the btext console
outb(0x87,0x2e);
outb(0x87,0x2e);
pnp_write_config(CONSOLE_SERIAL_DEV, 0x24, 0x84 | (1 << 6));
- w83627hf_enable_dev(CONSOLE_SERIAL_DEV, TTYS0_BASE);
+ w83627hf_enable_dev(CONSOLE_SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
}
else {
printk_debug("ERROR - could not find IOAPIC PCI 1:00.1\n");
- printk_debug("DEBUG: Dev= %p\n", dev);
+ printk_debug("CONFIG_DEBUG: Dev= %p\n", dev);
}
/* PXHd apic 5 */
dev = dev_find_slot(1, PCI_DEVFN(0x00,3));
}
else {
printk_debug("ERROR - could not find IOAPIC PCI 1:00.3\n");
- printk_debug("DEBUG: Dev= %p\n", dev);
+ printk_debug("CONFIG_DEBUG: Dev= %p\n", dev);
}
}
##
## Only use the option table in a normal image
##
-default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 128 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 128 * 1024
include /config/nofailovercalculation.lb
## Set all of the defaults for an x86 architecture
##
driver mainboard.o
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
object reset.o
##
## Romcc output
##
makerule ./failover.E
- depends "$(MAINBOARD)/failover.c ../romcc"
- action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/failover.c ../romcc"
+ action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/failover.c ../romcc"
- action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/failover.c ../romcc"
+ action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/failover.c -o $@"
end
makerule ./auto.E
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -E -mcpu=p4 -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -E -mcpu=p4 -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -mcpu=p4 -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -mcpu=p4 -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
##
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_LOGICAL_CPUS
uses CONFIG_MAX_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
-uses _RAMBASE
+uses CONFIG_RAMBASE
uses CONFIG_GDB_STUB
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_BTEXT
uses CC
-uses HOSTCC
-uses CROSS_COMPILE
-uses OBJCOPY
+uses CONFIG_HOSTCC
+uses CONFIG_CROSS_COMPILE
+uses CONFIG_OBJCOPY
###
###
##
-## ROM_SIZE is the size of boot ROM that this board will use.
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
##
-default ROM_SIZE=1048576
+default CONFIG_ROM_SIZE=1048576
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## Delay timer options
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=16
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=16
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
##
## Move the default coreboot cmos range off of AMD RTC registers
##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
+default CONFIG_LB_CKS_RANGE_START=49
+default CONFIG_LB_CKS_RANGE_END=122
+default CONFIG_LB_CKS_LOC=123
##
## Build code for SMP support
##
## Clean up the motherboard id strings
##
-default MAINBOARD_PART_NUMBER="X6DHE_g"
-default MAINBOARD_VENDOR= "Supermicro"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x15D9
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x6080
+default CONFIG_MAINBOARD_PART_NUMBER="X6DHE_g"
+default CONFIG_MAINBOARD_VENDOR= "Supermicro"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x15D9
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x6080
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 32K heap
##
-default HEAP_SIZE=0x8000
+default CONFIG_HEAP_SIZE=0x8000
###
### Compute the location and size of where this firmware image
### (coreboot plus bootloader) will live in the boot rom chip.
###
-default FALLBACK_SIZE=131072
+default CONFIG_FALLBACK_SIZE=131072
##
## Coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00004000
+default CONFIG_RAMBASE=0x00004000
##
## Load the payload from the ROM
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## Disable the gdb stub by default
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
##
## Don't enable the btext console
outb(0x87,0x2e);
outb(0x87,0x2e);
pnp_write_config(CONSOLE_SERIAL_DEV, 0x24, 0x84 | (1 << 6));
- pc87427_enable_dev(CONSOLE_SERIAL_DEV, TTYS0_BASE);
+ pc87427_enable_dev(CONSOLE_SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
outb(0x87,0x2e);
outb(0x87,0x2e);
pnp_write_config(CONSOLE_SERIAL_DEV, 0x24, 0x84 | (1 << 6));
- w83627hf_enable_dev(CONSOLE_SERIAL_DEV, TTYS0_BASE);
+ w83627hf_enable_dev(CONSOLE_SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
}
else {
printk_debug("ERROR - could not find IOAPIC PCI 1:00.1\n");
- printk_debug("DEBUG: Dev= %p\n", dev);
+ printk_debug("CONFIG_DEBUG: Dev= %p\n", dev);
}
/* PXHd apic 5 */
dev = dev_find_slot(1, PCI_DEVFN(0x00,3));
}
else {
printk_debug("ERROR - could not find IOAPIC PCI 1:00.3\n");
- printk_debug("DEBUG: Dev= %p\n", dev);
+ printk_debug("CONFIG_DEBUG: Dev= %p\n", dev);
}
}
##
## Only use the option table in a normal image
##
-default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 128 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 128 * 1024
include /config/nofailovercalculation.lb
##
##
driver mainboard.o
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
object reset.o
##
## Romcc output
##
makerule ./failover.E
- depends "$(MAINBOARD)/failover.c ../romcc"
- action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/failover.c ../romcc"
+ action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/failover.c ../romcc"
- action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/failover.c ../romcc"
+ action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/failover.c -o $@"
end
makerule ./auto.E
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -E -mcpu=p4 -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -E -mcpu=p4 -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -mcpu=p4 -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -mcpu=p4 -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
##
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_LOGICAL_CPUS
uses CONFIG_MAX_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
-uses _RAMBASE
+uses CONFIG_RAMBASE
uses CONFIG_GDB_STUB
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_BTEXT
uses CC
-uses HOSTCC
-uses CROSS_COMPILE
-uses OBJCOPY
+uses CONFIG_HOSTCC
+uses CONFIG_CROSS_COMPILE
+uses CONFIG_OBJCOPY
###
###
##
-## ROM_SIZE is the size of boot ROM that this board will use.
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
##
-default ROM_SIZE=1048576
+default CONFIG_ROM_SIZE=1048576
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## Delay timer options
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=16
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=16
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
##
## Move the default coreboot cmos range off of AMD RTC registers
##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
+default CONFIG_LB_CKS_RANGE_START=49
+default CONFIG_LB_CKS_RANGE_END=122
+default CONFIG_LB_CKS_LOC=123
##
## Build code for SMP support
##
## Clean up the motherboard id strings
##
-default MAINBOARD_PART_NUMBER="X6DHR"
-default MAINBOARD_VENDOR= "Supermicro"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x15D9
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x5580
+default CONFIG_MAINBOARD_PART_NUMBER="X6DHR"
+default CONFIG_MAINBOARD_VENDOR= "Supermicro"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x15D9
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x5580
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 32K heap
##
-default HEAP_SIZE=0x8000
+default CONFIG_HEAP_SIZE=0x8000
###
### Compute the location and size of where this firmware image
### (coreboot plus bootloader) will live in the boot rom chip.
###
-default FALLBACK_SIZE=131072
+default CONFIG_FALLBACK_SIZE=131072
##
## Coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00004000
+default CONFIG_RAMBASE=0x00004000
##
## Load the payload from the ROM
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## Disable the gdb stub by default
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
##
## Don't enable the btext console
outb(0x87,0x2e);
outb(0x87,0x2e);
pnp_write_config(CONSOLE_SERIAL_DEV, 0x24, 0x84 | (1 << 6));
- w83627hf_enable_dev(CONSOLE_SERIAL_DEV, TTYS0_BASE);
+ w83627hf_enable_dev(CONSOLE_SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
##
## Only use the option table in a normal image
##
-default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 128 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 128 * 1024
include /config/nofailovercalculation.lb
##
##
driver mainboard.o
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
object reset.o
##
## Romcc output
##
makerule ./failover.E
- depends "$(MAINBOARD)/failover.c ../romcc"
- action "../romcc -fno-simplify-phi -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/failover.c ../romcc"
+ action "../romcc -fno-simplify-phi -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/failover.c ../romcc"
- action "../romcc -fno-simplify-phi -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/failover.c ../romcc"
+ action "../romcc -fno-simplify-phi -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/failover.c -o $@"
end
makerule ./auto.E
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -fno-simplify-phi -E -mcpu=p4 -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -fno-simplify-phi -E -mcpu=p4 -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -fno-simplify-phi -mcpu=p4 -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -fno-simplify-phi -mcpu=p4 -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
##
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_LOGICAL_CPUS
uses CONFIG_MAX_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
-uses _RAMBASE
+uses CONFIG_RAMBASE
uses CONFIG_GDB_STUB
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_BTEXT
uses CC
-uses HOSTCC
-uses CROSS_COMPILE
-uses OBJCOPY
+uses CONFIG_HOSTCC
+uses CONFIG_CROSS_COMPILE
+uses CONFIG_OBJCOPY
###
###
##
-## ROM_SIZE is the size of boot ROM that this board will use.
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
##
-default ROM_SIZE=1048576
+default CONFIG_ROM_SIZE=1048576
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## Delay timer options
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=16
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=16
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
##
## Move the default coreboot cmos range off of AMD RTC registers
##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
+default CONFIG_LB_CKS_RANGE_START=49
+default CONFIG_LB_CKS_RANGE_END=122
+default CONFIG_LB_CKS_LOC=123
##
## Build code for SMP support
##
## Clean up the motherboard id strings
##
-default MAINBOARD_PART_NUMBER="X6DHR"
-default MAINBOARD_VENDOR= "Supermicro"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x15D9
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x5580
+default CONFIG_MAINBOARD_PART_NUMBER="X6DHR"
+default CONFIG_MAINBOARD_VENDOR= "Supermicro"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x15D9
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x5580
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 32K heap
##
-default HEAP_SIZE=0x8000
+default CONFIG_HEAP_SIZE=0x8000
###
### Compute the location and size of where this firmware image
### (coreboot plus bootloader) will live in the boot rom chip.
###
-default FALLBACK_SIZE=131072
+default CONFIG_FALLBACK_SIZE=131072
##
## Coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00004000
+default CONFIG_RAMBASE=0x00004000
##
## Load the payload from the ROM
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## Disable the gdb stub by default
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
##
## Don't enable the btext console
outb(0x87,0x2e);
outb(0x87,0x2e);
pnp_write_config(CONSOLE_SERIAL_DEV, 0x24, 0x84 | (1 << 6));
- w83627hf_enable_dev(CONSOLE_SERIAL_DEV, TTYS0_BASE);
+ w83627hf_enable_dev(CONSOLE_SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
##
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
arch i386 end
#dir /drivers/si/3114
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE
object get_bus_conf.o
object irq_tables.o
end
-if HAVE_ACPI_TABLES
+if CONFIG_HAVE_ACPI_TABLES
object acpi_tables.o
object fadt.o
makerule dsdt.c
- depends "$(MAINBOARD)/acpi/*.asl"
- action "iasl -p $(CURDIR)/dsdt -tc $(MAINBOARD)/acpi/dsdt.asl"
+ depends "$(CONFIG_MAINBOARD)/acpi/*.asl"
+ action "iasl -p $(CURDIR)/dsdt -tc $(CONFIG_MAINBOARD)/acpi/dsdt.asl"
action "mv dsdt.hex dsdt.c"
end
object ./dsdt.o
if CONFIG_USE_INIT
makerule ./cache_as_ram_auto.o
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
end
else
makerule ./cache_as_ram_auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
end
##
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses HAVE_ACPI_TABLES
-uses HAVE_ACPI_RESUME
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_HAVE_ACPI_TABLES
+uses CONFIG_HAVE_ACPI_RESUME
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_MAX_CPUS
uses CONFIG_MAX_PHYSICAL_CPUS
uses CONFIG_LOGICAL_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
-uses _RAMBASE
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_RAMBASE
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_SERIAL8250
-uses HAVE_INIT_TIMER
+uses CONFIG_HAVE_INIT_TIMER
uses CONFIG_GDB_STUB
uses CONFIG_GDB_STUB
-uses CROSS_COMPILE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
-uses HW_MEM_HOLE_SIZEK
-uses HT_CHAIN_UNITID_BASE
-uses HT_CHAIN_END_UNITID_BASE
-uses SB_HT_CHAIN_ON_BUS0
-
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
-uses DCACHE_RAM_GLOBAL_VAR_SIZE
+uses CONFIG_HW_MEM_HOLE_SIZEK
+uses CONFIG_HT_CHAIN_UNITID_BASE
+uses CONFIG_HT_CHAIN_END_UNITID_BASE
+uses CONFIG_SB_HT_CHAIN_ON_BUS0
+
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
+uses CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE
uses CONFIG_USE_INIT
-uses SB_HT_CHAIN_UNITID_OFFSET_ONLY
+uses CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY
uses CONFIG_USE_PRINTK_IN_CAR
uses CONFIG_VIDEO_MB
uses CONFIG_GFXUMA
-uses HAVE_MAINBOARD_RESOURCES
+uses CONFIG_HAVE_MAINBOARD_RESOURCES
###
### Build options
###
##
-## ROM_SIZE is the size of boot ROM that this board will use.
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
##
-default ROM_SIZE=524288
+default CONFIG_ROM_SIZE=524288
##
-## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
+## CONFIG_FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
##
-#default FALLBACK_SIZE=131072
+#default CONFIG_FALLBACK_SIZE=131072
#256K
-default FALLBACK_SIZE=0x40000
+default CONFIG_FALLBACK_SIZE=0x40000
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=11
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=11
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
## ACPI tables will be included
-default HAVE_ACPI_TABLES=1
+default CONFIG_HAVE_ACPI_TABLES=1
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=0
+default CONFIG_HAVE_OPTION_TABLE=0
##
## Move the default coreboot cmos range off of AMD RTC registers
##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
+default CONFIG_LB_CKS_RANGE_START=49
+default CONFIG_LB_CKS_RANGE_END=122
+default CONFIG_LB_CKS_LOC=123
##
## Build code for SMP support
#1G memory hole
-default HW_MEM_HOLE_SIZEK=0x100000
+default CONFIG_HW_MEM_HOLE_SIZEK=0x100000
#VGA Console
default CONFIG_CONSOLE_VGA=1
# BTDC: Only one HT device on Herring.
#HT Unit ID offset
-#default HT_CHAIN_UNITID_BASE=0x6
-default HT_CHAIN_UNITID_BASE=0x0
+#default CONFIG_HT_CHAIN_UNITID_BASE=0x6
+default CONFIG_HT_CHAIN_UNITID_BASE=0x0
#real SB Unit ID
-default HT_CHAIN_END_UNITID_BASE=0x1
+default CONFIG_HT_CHAIN_END_UNITID_BASE=0x1
#make the SB HT chain on bus 0
-default SB_HT_CHAIN_ON_BUS0=1
+default CONFIG_SB_HT_CHAIN_ON_BUS0=1
##
## enable CACHE_AS_RAM specifics
##
-default USE_DCACHE_RAM=1
-default DCACHE_RAM_BASE=0xc8000
-default DCACHE_RAM_SIZE=0x8000
-default DCACHE_RAM_GLOBAL_VAR_SIZE=0x01000
+default CONFIG_USE_DCACHE_RAM=1
+default CONFIG_DCACHE_RAM_BASE=0xc8000
+default CONFIG_DCACHE_RAM_SIZE=0x8000
+default CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE=0x01000
default CONFIG_USE_INIT=0
##
##
## Clean up the motherboard id strings
##
-default MAINBOARD_PART_NUMBER="tim8690"
-default MAINBOARD_VENDOR="technexion"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x1022
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x3050
+default CONFIG_MAINBOARD_PART_NUMBER="tim8690"
+default CONFIG_MAINBOARD_VENDOR="technexion"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x1022
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x3050
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE=0x4000
+default CONFIG_HEAP_SIZE=0x4000
##
## Only use the option table in a normal image
##
-#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
+#default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 0
##
## coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00004000
+default CONFIG_RAMBASE=0x00004000
##
## Load the payload from the ROM
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## Disable the gdb stub by default
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
default CONFIG_VIDEO_MB=1
default CONFIG_GFXUMA=1
-default HAVE_MAINBOARD_RESOURCES=1
+default CONFIG_HAVE_MAINBOARD_RESOURCES=1
### End Options.lb
end
extern u8 AmlCode[];
-#if ACPI_SSDTX_NUM >= 1
+#if CONFIG_ACPI_SSDTX_NUM >= 1
extern u8 AmlCode_ssdt2[];
extern u8 AmlCode_ssdt3[];
extern u8 AmlCode_ssdt4[];
current += ssdt->length;
acpi_add_table(rsdt, ssdt);
-#if ACPI_SSDTX_NUM >= 1
+#if CONFIG_ACPI_SSDTX_NUM >= 1
/* same htio, but different position? We may have to copy, change HCIN, and recalculate the checknum and add_table */
#include "cpu/amd/model_fxx/fidvid.c"
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
#include "northbridge/amd/amdk8/early_ht.c"
fallback_image:
post_code(0x25);
}
-#endif /* USE_FALLBACK_IMAGE == 1 */
+#endif /* CONFIG_USE_FALLBACK_IMAGE == 1 */
void real_main(unsigned long bist, unsigned long cpu_init_detectedx);
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
failover_process(bist, cpu_init_detectedx);
#endif
real_main(bist, cpu_init_detectedx);
u32 bsp_apicid = 0;
msr_t msr;
struct cpuid_result cpuid1;
- struct sys_info *sysinfo = (struct sys_info *)(DCACHE_RAM_BASE + DCACHE_RAM_SIZE - DCACHE_RAM_GLOBAL_VAR_SIZE);
+ struct sys_info *sysinfo = (struct sys_info *)(CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE);
if (bist == 0) {
sb600_lpc_init();
/* it8712f_enable_serial does not use its 1st parameter. */
- it8712f_enable_serial(0, TTYS0_BASE);
+ it8712f_enable_serial(0, CONFIG_TTYS0_BASE);
it8712f_kill_watchdog();
uart_init();
console_init();
/* PCI interrupts are level triggered, and are
* associated with a specific bus/device/function tuple.
*/
-#if HAVE_ACPI_TABLES == 0
+#if CONFIG_HAVE_ACPI_TABLES == 0
#define PCI_INT(bus, dev, fn, pin) \
smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, (bus), (((dev)<<2)|(fn)), apicid_sb600, (pin))
#else
-default ROM_SIZE = 128 * 1024
-default FALLBACK_SIZE = 0x10000
+default CONFIG_ROM_SIZE = 128 * 1024
+default CONFIG_FALLBACK_SIZE = 0x10000
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 32 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 32 * 1024
include /config/nofailovercalculation.lb
##
##
driver mainboard.o
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
# object reset.o
##
## Romcc output
##
makerule ./failover.E
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./auto.E
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -E -mcpu=i386 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -E -mcpu=i386 -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -mcpu=i386 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -mcpu=i386 -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
##
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_COMPRESS
uses CONFIG_ROM_PAYLOAD
uses CONFIG_USE_INIT
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses HAVE_MP_TABLE
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
uses CONFIG_CONSOLE_SERIAL8250
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x2f8
+default CONFIG_TTYS0_BASE=0x2f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
-default DEFAULT_CONSOLE_LOGLEVEL=9
-default MAXIMUM_CONSOLE_LOGLEVEL=9
-## ROM_SIZE is the size of boot ROM that this board will use.
-default ROM_SIZE = 256*1024
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=9
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=9
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
+default CONFIG_ROM_SIZE = 256*1024
###
### Build options
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## no MP table
##
-default HAVE_MP_TABLE=0
+default CONFIG_HAVE_MP_TABLE=0
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=0
+default CONFIG_HAVE_HARD_RESET=0
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=7
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=7
#object irq_tables.o
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
-default FALLBACK_SIZE = 131072
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
+default CONFIG_FALLBACK_SIZE = 131072
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE=0x4000
+default CONFIG_HEAP_SIZE=0x4000
##
## Only use the option table in a normal image
##
-#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
+#default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
#
# CBFS
/* hack for IDIOTIC need to fix rom_start */
printk_err("Patching rom_start due to sc520 limits\n");
rom_start = 0x09400000 + 0xe0000;
- rom_end = rom_start + PAYLOAD_SIZE - 1;
+ rom_end = rom_start + CONFIG_PAYLOAD_SIZE - 1;
printk_err("TS5300 EXIT %s\n", __func__);
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
arch i386 end
driver mainboard.o
-if HAVE_PIRQ_TABLE
+if CONFIG_HAVE_PIRQ_TABLE
object irq_tables.o
end
makerule ./failover.E
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./auto.E
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -E -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -E -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
mainboardinit cpu/x86/16bit/entry16.inc
mainboardinit cpu/x86/32bit/entry32.inc
ldscript /cpu/x86/16bit/entry16.lds
ldscript /cpu/x86/32bit/entry32.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
mainboardinit arch/i386/lib/cpu_reset.inc
mainboardinit arch/i386/lib/id.inc
ldscript /arch/i386/lib/id.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_ROM_PAYLOAD
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
uses CONFIG_SPLASH_GRAPHIC
uses CONFIG_GX1_VIDEO
uses CONFIG_GX1_VIDEOMODE
-uses PIRQ_ROUTE
+uses CONFIG_PIRQ_ROUTE
## Enable VGA with a splash screen (only 640x480 to run on most monitors).
## We want to support up to 1024x768@16 so we need 2MiB video memory.
default CONFIG_GX1_VIDEOMODE = 0
default CONFIG_SPLASH_GRAPHIC = 1
default CONFIG_VIDEO_MB = 2
-default HAVE_PIRQ_TABLE=0
-default PIRQ_ROUTE=1
+default CONFIG_HAVE_PIRQ_TABLE=0
+default CONFIG_PIRQ_ROUTE=1
-default ROM_SIZE = 256 * 1024
-default MAINBOARD_VENDOR = "TeleVideo"
-default MAINBOARD_PART_NUMBER = "TC7020"
-default HAVE_FALLBACK_BOOT = 1
-default HAVE_MP_TABLE = 0
-default HAVE_HARD_RESET = 0
+default CONFIG_ROM_SIZE = 256 * 1024
+default CONFIG_MAINBOARD_VENDOR = "TeleVideo"
+default CONFIG_MAINBOARD_PART_NUMBER = "TC7020"
+default CONFIG_HAVE_FALLBACK_BOOT = 1
+default CONFIG_HAVE_MP_TABLE = 0
+default CONFIG_HAVE_HARD_RESET = 0
default CONFIG_UDELAY_TSC = 1
default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 1
-default HAVE_PIRQ_TABLE = 1
-default IRQ_SLOT_COUNT = 3 # Soldered NIC, internal USB, mini PCI slot
-default HAVE_OPTION_TABLE = 0
-default ROM_IMAGE_SIZE = 64 * 1024
-default FALLBACK_SIZE = 128 * 1024
-default STACK_SIZE = 8 * 1024
-default HEAP_SIZE = 16 * 1024
-default USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_HAVE_PIRQ_TABLE = 1
+default CONFIG_IRQ_SLOT_COUNT = 3 # Soldered NIC, internal USB, mini PCI slot
+default CONFIG_HAVE_OPTION_TABLE = 0
+default CONFIG_ROM_IMAGE_SIZE = 64 * 1024
+default CONFIG_FALLBACK_SIZE = 128 * 1024
+default CONFIG_STACK_SIZE = 8 * 1024
+default CONFIG_HEAP_SIZE = 16 * 1024
+default CONFIG_USE_OPTION_TABLE = 0
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
-default CROSS_COMPILE = ""
-default CC = "$(CROSS_COMPILE)gcc "
-default HOSTCC = "gcc"
+default CONFIG_CROSS_COMPILE = ""
+default CC = "$(CONFIG_CROSS_COMPILE)gcc "
+default CONFIG_HOSTCC = "gcc"
default CONFIG_CONSOLE_SERIAL8250 = 1
-default TTYS0_BAUD = 115200
-default TTYS0_BASE = 0x3f8
-default TTYS0_LCS = 0x3 # 8n1
-default DEFAULT_CONSOLE_LOGLEVEL = 6
-default MAXIMUM_CONSOLE_LOGLEVEL = 6
+default CONFIG_TTYS0_BAUD = 115200
+default CONFIG_TTYS0_BASE = 0x3f8
+default CONFIG_TTYS0_LCS = 0x3 # 8n1
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 6
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 6
#
# CBFS
static void main(unsigned long bist)
{
/* Initialize the serial console. */
- pc97317_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ pc97317_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
const struct irq_routing_table intel_irq_routing_table = {
PIRQ_SIGNATURE, /* u32 signature */
PIRQ_VERSION, /* u16 version */
- 32+16*IRQ_SLOT_COUNT, /* There can be a total of IRQ_SLOT_COUNT devices on the bus */
+ 32+16*CONFIG_IRQ_SLOT_COUNT, /* There can be a total of CONFIG_IRQ_SLOT_COUNT devices on the bus */
0x00, /* Where the interrupt router lies (bus) */
(0x12<<3)|0x0, /* Where the interrupt router lies (dev) */
EXCLUSIVE_PCI_IRQS, /* IRQs devoted exclusively to PCI usage */
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
arch i386 end
driver mainboard.o
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
# object reset.o
-if HAVE_ACPI_TABLES
+if CONFIG_HAVE_ACPI_TABLES
object fadt.o
object dsdt.o
object acpi_tables.o
end
makerule ./failover.E
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./auto.E
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -E -mcpu=p3 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -E -mcpu=p3 -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -mcpu=p3 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -mcpu=p3 -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
mainboardinit cpu/x86/16bit/entry16.inc
mainboardinit cpu/x86/32bit/entry32.inc
ldscript /cpu/x86/16bit/entry16.lds
ldscript /cpu/x86/32bit/entry32.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
mainboardinit arch/i386/lib/cpu_reset.inc
mainboardinit arch/i386/lib/id.inc
ldscript /arch/i386/lib/id.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
uses CONFIG_UDELAY_TSC
uses CONFIG_VIDEO_MB
-uses CROSS_COMPILE
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses FALLBACK_SIZE
-uses HAVE_ACPI_TABLES
-uses HAVE_ACPI_RESUME
-uses HAVE_FALLBACK_BOOT
-uses HAVE_MP_TABLE
-uses HAVE_OPTION_TABLE
-uses HAVE_PIRQ_TABLE
-uses HEAP_SIZE
-uses HOSTCC
-uses IRQ_SLOT_COUNT
+uses CONFIG_CROSS_COMPILE
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_HAVE_ACPI_TABLES
+uses CONFIG_HAVE_ACPI_RESUME
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_HOSTCC
+uses CONFIG_IRQ_SLOT_COUNT
uses COREBOOT_EXTRA_VERSION
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses OBJCOPY
-uses PAYLOAD_SIZE
-uses _RAMBASE
-uses _ROMBASE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
-uses ROM_SIZE
-uses STACK_SIZE
-uses TTYS0_BASE
-uses TTYS0_BAUD
-uses TTYS0_LCS
-uses USE_FALLBACK_IMAGE
-uses USE_OPTION_TABLE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_OBJCOPY
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_RAMBASE
+uses CONFIG_ROMBASE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
+uses CONFIG_ROM_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_LCS
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
-default ROM_SIZE = 512 * 1024
-default ROM_IMAGE_SIZE = 128 * 1024
-default HAVE_FALLBACK_BOOT = 1
-default FALLBACK_SIZE = 256 * 1024
+default CONFIG_ROM_SIZE = 512 * 1024
+default CONFIG_ROM_IMAGE_SIZE = 128 * 1024
+default CONFIG_HAVE_FALLBACK_BOOT = 1
+default CONFIG_FALLBACK_SIZE = 256 * 1024
default CONFIG_UDELAY_TSC = 1
default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 1
-default HAVE_PIRQ_TABLE = 1
-default IRQ_SLOT_COUNT = 7
-default HAVE_MP_TABLE = 0
-default HAVE_ACPI_TABLES = 0
+default CONFIG_HAVE_PIRQ_TABLE = 1
+default CONFIG_IRQ_SLOT_COUNT = 7
+default CONFIG_HAVE_MP_TABLE = 0
+default CONFIG_HAVE_ACPI_TABLES = 0
default CONFIG_IOAPIC = 0
-default HAVE_OPTION_TABLE = 0
+default CONFIG_HAVE_OPTION_TABLE = 0
default CONFIG_CONSOLE_VGA = 0
default CONFIG_PCI_ROM_RUN = 0
default CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0
default CONFIG_VIDEO_MB = 0
-default STACK_SIZE = 0x2000
-default HEAP_SIZE = 0x4000
-default _RAMBASE = 0x00004000
-default USE_OPTION_TABLE = 0
+default CONFIG_STACK_SIZE = 0x2000
+default CONFIG_HEAP_SIZE = 0x4000
+default CONFIG_RAMBASE = 0x00004000
+default CONFIG_USE_OPTION_TABLE = 0
default CONFIG_ROM_PAYLOAD = 1
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
default CONFIG_CONSOLE_SERIAL8250 = 1
-default TTYS0_BAUD = 115200
-default TTYS0_BASE = 0x3f8
-default TTYS0_LCS = 0x3 # 8n1
-default DEFAULT_CONSOLE_LOGLEVEL = 9
-default MAXIMUM_CONSOLE_LOGLEVEL = 9
-default MAINBOARD_VENDOR = "THOMSON"
-default MAINBOARD_PART_NUMBER = "IP1000"
+default CONFIG_TTYS0_BAUD = 115200
+default CONFIG_TTYS0_BASE = 0x3f8
+default CONFIG_TTYS0_LCS = 0x3 # 8n1
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
+default CONFIG_MAINBOARD_VENDOR = "THOMSON"
+default CONFIG_MAINBOARD_PART_NUMBER = "IP1000"
#
# CBFS
#
hard_reset();
}
- smscsuperio_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ smscsuperio_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
mb_gpio_init();
uart_init();
console_init();
const struct irq_routing_table intel_irq_routing_table = {
PIRQ_SIGNATURE, /* u32 signature */
PIRQ_VERSION, /* u16 version */
- 32+16*IRQ_SLOT_COUNT, /* there can be total 7 devices on the bus */
+ 32+16*CONFIG_IRQ_SLOT_COUNT, /* there can be total 7 devices on the bus */
0x00, /* Where the interrupt router lies (bus) */
(0x1f<<3)|0x0, /* Where the interrupt router lies (dev) */
0, /* IRQs devoted exclusively to PCI usage */
## Build the objects we have code for in this directory.
##
-addaction coreboot.a "$(CROSS_COMPILE)ranlib coreboot.a"
+addaction coreboot.a "$(CONFIG_CROSS_COMPILE)ranlib coreboot.a"
## Config file for the Total Impact briQ
##
-uses TTYS0_DIV
+uses CONFIG_TTYS0_DIV
uses CONFIG_CBFS
uses CONFIG_ARCH_X86
-uses TTYS0_BASE
+uses CONFIG_TTYS0_BASE
uses CONFIG_BRIQ_750FX
uses CONFIG_BRIQ_7400
-uses ISA_IO_BASE
-uses ISA_MEM_BASE
-uses PCIC0_CFGADDR
-uses PCIC0_CFGDATA
-uses _IO_BASE
-uses HAVE_OPTION_TABLE
+uses CONFIG_ISA_IO_BASE
+uses CONFIG_ISA_MEM_BASE
+uses CONFIG_PCIC0_CFGADDR
+uses CONFIG_PCIC0_CFGDATA
+uses CONFIG_IO_BASE
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_COMPRESS
-uses DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
uses CONFIG_USE_INIT
-uses NO_POST
+uses CONFIG_NO_POST
uses CONFIG_CONSOLE_SERIAL8250
uses CONFIG_IDE_PAYLOAD
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses IDE_BOOT_DRIVE
-uses IDE_SWAB IDE_OFFSET
-uses ROM_SIZE
-uses ROM_IMAGE_SIZE
-uses _RESET
-uses _EXCEPTION_VECTORS
-uses _ROMBASE
-uses _ROMSTART
-uses _RAMBASE
-uses _RAMSTART
-uses STACK_SIZE
-uses HEAP_SIZE
+uses CONFIG_IDE_BOOT_DRIVE
+uses CONFIG_IDE_SWAB CONFIG_IDE_OFFSET
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_RESET
+uses CONFIG_EXCEPTION_VECTORS
+uses CONFIG_ROMBASE
+uses CONFIG_ROMSTART
+uses CONFIG_RAMBASE
+uses CONFIG_RAMSTART
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
uses CONFIG_BRIQ_750FX
uses CONFIG_BRIQ_7400
uses CONFIG_SYS_CLK_FREQ
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses CROSS_COMPILE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
##
## Set memory map
##
-default ISA_IO_BASE=0x80000000
-default ISA_MEM_BASE=0xc0000000
-default PCIC0_CFGADDR=0xff5f8000
-default PCIC0_CFGDATA=0xff5f8010
-default _IO_BASE=ISA_IO_BASE
+default CONFIG_ISA_IO_BASE=0x80000000
+default CONFIG_ISA_MEM_BASE=0xc0000000
+default CONFIG_PCIC0_CFGADDR=0xff5f8000
+default CONFIG_PCIC0_CFGDATA=0xff5f8010
+default CONFIG_IO_BASE=CONFIG_ISA_IO_BASE
##
## The briQ uses weird clocking, 4 = 115200
##
-default TTYS0_DIV=4
+default CONFIG_TTYS0_DIV=4
##
## Set UART base address
##
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc"
+default CONFIG_HOSTCC="gcc"
## use a cross compiler
-#default CROSS_COMPILE="powerpc-eabi-"
-#default CROSS_COMPILE="ppc_74xx-"
+#default CONFIG_CROSS_COMPILE="powerpc-eabi-"
+#default CONFIG_CROSS_COMPILE="ppc_74xx-"
default CONFIG_ARCH_X86=0
## Use stage 1 initialization code
default CONFIG_COMPRESS=0
## Turn off POST codes
-default NO_POST=1
+default CONFIG_NO_POST=1
## Enable serial console
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
default CONFIG_CONSOLE_SERIAL8250=1
## Boot linux from IDE
default CONFIG_IDE_PAYLOAD=1
-default IDE_BOOT_DRIVE=0
-default IDE_SWAB=1
-default IDE_OFFSET=0
+default CONFIG_IDE_BOOT_DRIVE=0
+default CONFIG_IDE_SWAB=1
+default CONFIG_IDE_OFFSET=0
# ROM is 1Mb
-default ROM_SIZE=1048576
+default CONFIG_ROM_SIZE=1048576
# Set stack and heap sizes (stage 2)
-default STACK_SIZE=0x10000
-default HEAP_SIZE=0x10000
+default CONFIG_STACK_SIZE=0x10000
+default CONFIG_HEAP_SIZE=0x10000
##
## System clock
# Sandpoint Demo Board
## Base of ROM
-default _ROMBASE=0xfff00000
+default CONFIG_ROMBASE=0xfff00000
## Sandpoint reset vector
-default _RESET=_ROMBASE+0x100
+default CONFIG_RESET=CONFIG_ROMBASE+0x100
## Exception vectors (other than reset vector)
-default _EXCEPTION_VECTORS=_RESET+0x100
+default CONFIG_EXCEPTION_VECTORS=CONFIG_RESET+0x100
## Start of coreboot in the boot rom
-## = _RESET + exeception vector table size
-default _ROMSTART=_RESET+0x3100
+## = CONFIG_RESET + exeception vector table size
+default CONFIG_ROMSTART=CONFIG_RESET+0x3100
## Coreboot C code runs at this location in RAM
-default _RAMBASE=0x00100000
-default _RAMSTART=0x00100000
+default CONFIG_RAMBASE=0x00100000
+default CONFIG_RAMSTART=0x00100000
default CONFIG_BRIQ_750FX=1
#default CONFIG_BRIQ_7400=1
/*
* Enable UART
*/
- uart8250_init(TTYS0_BASE, TTYS0_DIV, TTYS0_LCS);
+ uart8250_init(CONFIG_TTYS0_BASE, CONFIG_TTYS0_DIV, CONFIG_TTYS0_LCS);
printk_info("briQ initialized...\n");
}
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
arch i386 end
driver mainboard.o
-if HAVE_PIRQ_TABLE
+if CONFIG_HAVE_PIRQ_TABLE
object irq_tables.o
end
makerule ./failover.E
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -E -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -E -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -O2 -mcpu=p2 --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./auto.E
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -E -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -E -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- # depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- depends "$(MAINBOARD)/auto.c ../romcc"
- action "../romcc -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ # depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ depends "$(CONFIG_MAINBOARD)/auto.c ../romcc"
+ action "../romcc -O2 -mcpu=p2 -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
mainboardinit cpu/x86/16bit/entry16.inc
mainboardinit cpu/x86/32bit/entry32.inc
ldscript /cpu/x86/16bit/entry16.lds
ldscript /cpu/x86/32bit/entry32.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
mainboardinit arch/i386/lib/cpu_reset.inc
mainboardinit arch/i386/lib/id.inc
ldscript /arch/i386/lib/id.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_ROM_PAYLOAD
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses HAVE_MP_TABLE
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
-default ROM_SIZE = 256 * 1024
-default HAVE_FALLBACK_BOOT = 1
-default HAVE_MP_TABLE = 0
-default HAVE_HARD_RESET = 0
+default CONFIG_ROM_SIZE = 256 * 1024
+default CONFIG_HAVE_FALLBACK_BOOT = 1
+default CONFIG_HAVE_MP_TABLE = 0
+default CONFIG_HAVE_HARD_RESET = 0
default CONFIG_UDELAY_TSC = 1
default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 1
-default HAVE_PIRQ_TABLE = 0
-default IRQ_SLOT_COUNT = 0 # Override this in targets/*/Config.lb.
-default MAINBOARD_VENDOR = "N/A" # Override this in targets/*/Config.lb.
-default MAINBOARD_PART_NUMBER = "N/A" # Override this in targets/*/Config.lb.
-default ROM_IMAGE_SIZE = 64 * 1024
-default FALLBACK_SIZE = 128 * 1024
-default STACK_SIZE = 8 * 1024
-default HEAP_SIZE = 16 * 1024
-default HAVE_OPTION_TABLE = 0
-#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_HAVE_PIRQ_TABLE = 0
+default CONFIG_IRQ_SLOT_COUNT = 0 # Override this in targets/*/Config.lb.
+default CONFIG_MAINBOARD_VENDOR = "N/A" # Override this in targets/*/Config.lb.
+default CONFIG_MAINBOARD_PART_NUMBER = "N/A" # Override this in targets/*/Config.lb.
+default CONFIG_ROM_IMAGE_SIZE = 64 * 1024
+default CONFIG_FALLBACK_SIZE = 128 * 1024
+default CONFIG_STACK_SIZE = 8 * 1024
+default CONFIG_HEAP_SIZE = 16 * 1024
+default CONFIG_HAVE_OPTION_TABLE = 0
+#default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 0
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
-default CROSS_COMPILE = ""
-default CC = "$(CROSS_COMPILE)gcc -m32"
-default HOSTCC = "gcc"
+default CONFIG_CROSS_COMPILE = ""
+default CC = "$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC = "gcc"
default CONFIG_CONSOLE_SERIAL8250 = 1
-default TTYS0_BAUD = 115200
-default TTYS0_BASE = 0x3f8
-default TTYS0_LCS = 0x3 # 8n1
-default DEFAULT_CONSOLE_LOGLEVEL = 9
-default MAXIMUM_CONSOLE_LOGLEVEL = 9
+default CONFIG_TTYS0_BAUD = 115200
+default CONFIG_TTYS0_BASE = 0x3f8
+default CONFIG_TTYS0_LCS = 0x3 # 8n1
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
default CONFIG_CONSOLE_VGA = 1
default CONFIG_PCI_ROM_RUN = 1
if (bist == 0)
early_mtrr_init();
- pc87309_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ pc87309_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
report_bist_failure(bist);
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
default CONFIG_ROM_PAYLOAD = 1
##
driver mainboard.o
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
object reset.o
if CONFIG_USE_INIT
makerule ./auto.o
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
end
else
makerule ./auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
end
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_USE_INIT
uses CONFIG_MAX_CPUS
uses CONFIG_MAX_PHYSICAL_CPUS
uses CONFIG_LOGICAL_CPUS
-uses SERIAL_CPU_INIT
+uses CONFIG_SERIAL_CPU_INIT
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
-uses _RAMBASE
+uses CONFIG_RAMBASE
uses CONFIG_GDB_STUB
-uses CROSS_COMPILE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_SERIAL8250
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
uses CONFIG_CONSOLE_BTEXT
-uses HAVE_INIT_TIMER
+uses CONFIG_HAVE_INIT_TIMER
uses CONFIG_GDB_STUB
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
uses CONFIG_USE_PRINTK_IN_CAR
-## ROM_SIZE is the size of boot ROM that this board will use.
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
#512K bytes
-default ROM_SIZE=524288
+default CONFIG_ROM_SIZE=524288
#1M bytes
-#default ROM_SIZE=1048576
+#default CONFIG_ROM_SIZE=1048576
##
-## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
+## CONFIG_FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
##
-default FALLBACK_SIZE=131072
+default CONFIG_FALLBACK_SIZE=131072
###
### Build options
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
## Delay timer options
##
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=15
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=15
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
##
## Move the default coreboot cmos range off of AMD RTC registers
##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
+default CONFIG_LB_CKS_RANGE_START=49
+default CONFIG_LB_CKS_RANGE_END=122
+default CONFIG_LB_CKS_LOC=123
##
## Build code for SMP support
default CONFIG_MAX_PHYSICAL_CPUS=2
default CONFIG_LOGICAL_CPUS=1
-default SERIAL_CPU_INIT=0
+default CONFIG_SERIAL_CPU_INIT=0
#BTEXT Console
#default CONFIG_CONSOLE_BTEXT=1
##
## enable CACHE_AS_RAM specifics
##
-default USE_DCACHE_RAM=1
-#default DCACHE_RAM_BASE=0xF2000000
-default DCACHE_RAM_BASE=0xcf000
-default DCACHE_RAM_SIZE=0x1000
+default CONFIG_USE_DCACHE_RAM=1
+#default CONFIG_DCACHE_RAM_BASE=0xF2000000
+default CONFIG_DCACHE_RAM_BASE=0xcf000
+default CONFIG_DCACHE_RAM_SIZE=0x1000
default CONFIG_USE_PRINTK_IN_CAR=1
##
## Clean up the motherboard id strings
##
-default MAINBOARD_PART_NUMBER="s2735"
-default MAINBOARD_VENDOR="Tyan"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x10f1
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2735
+default CONFIG_MAINBOARD_PART_NUMBER="s2735"
+default CONFIG_MAINBOARD_VENDOR="Tyan"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x10f1
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2735
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE=0x4000
+default CONFIG_HEAP_SIZE=0x4000
##
## Only use the option table in a normal image
##
-default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
##
## Coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00004000
+default CONFIG_RAMBASE=0x00004000
##
## Load the payload from the ROM
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## Disable the gdb stub by default
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
### End Options.lb
#
#include "cpu/x86/car/copy_and_run.c"
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
#include "southbridge/intel/i82801er/cmos_failover.c"
// post_code(0x32);
- w83627hf_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ w83627hf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
}
__asm__ volatile (
- /* set new esp */ /* before _RAMBASE */
+ /* set new esp */ /* before CONFIG_RAMBASE */
"subl %0, %%ebp\n\t"
"subl %0, %%esp\n\t"
- ::"a"( (DCACHE_RAM_BASE + DCACHE_RAM_SIZE)- _RAMBASE )
+ ::"a"( (CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE)- CONFIG_RAMBASE )
);
{
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
arch i386 end
#dir /drivers/si/3114
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
if CONFIG_USE_INIT
makerule ./auto.o
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
end
else
makerule ./auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
##
## Build our 16 bit and 32 bit coreboot entry code
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
end
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
end
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_MAX_CPUS
uses CONFIG_MAX_PHYSICAL_CPUS
uses CONFIG_LOGICAL_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
-uses _RAMBASE
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_RAMBASE
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_SERIAL8250
-uses HAVE_INIT_TIMER
+uses CONFIG_HAVE_INIT_TIMER
uses CONFIG_GDB_STUB
uses CONFIG_GDB_STUB
-uses CROSS_COMPILE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
-uses HW_MEM_HOLE_SIZEK
+uses CONFIG_HW_MEM_HOLE_SIZEK
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
uses CONFIG_USE_INIT
uses CONFIG_USE_PRINTK_IN_CAR
###
##
-## ROM_SIZE is the size of boot ROM that this board will use.
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
##
-default ROM_SIZE=524288
+default CONFIG_ROM_SIZE=524288
##
-## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
+## CONFIG_FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
##
-#default FALLBACK_SIZE=131072
+#default CONFIG_FALLBACK_SIZE=131072
#256K
-default FALLBACK_SIZE=0x40000
+default CONFIG_FALLBACK_SIZE=0x40000
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=12
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=12
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
##
## Move the default coreboot cmos range off of AMD RTC registers
##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
+default CONFIG_LB_CKS_RANGE_START=49
+default CONFIG_LB_CKS_RANGE_END=122
+default CONFIG_LB_CKS_LOC=123
##
## Build code for SMP support
default CONFIG_LOGICAL_CPUS=1
#1G memory hole
-default HW_MEM_HOLE_SIZEK=0x100000
+default CONFIG_HW_MEM_HOLE_SIZEK=0x100000
#VGA Console
default CONFIG_CONSOLE_VGA=1
##
## enable CACHE_AS_RAM specifics
##
-default USE_DCACHE_RAM=1
-default DCACHE_RAM_BASE=0xcf000
-default DCACHE_RAM_SIZE=0x1000
+default CONFIG_USE_DCACHE_RAM=1
+default CONFIG_DCACHE_RAM_BASE=0xcf000
+default CONFIG_DCACHE_RAM_SIZE=0x1000
default CONFIG_USE_INIT=0
##
##
## Clean up the motherboard id strings
##
-default MAINBOARD_PART_NUMBER="S2850"
-default MAINBOARD_VENDOR="Tyan"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x10f1
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2850
+default CONFIG_MAINBOARD_PART_NUMBER="S2850"
+default CONFIG_MAINBOARD_VENDOR="Tyan"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x10f1
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2850
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE=0x4000
+default CONFIG_HEAP_SIZE=0x4000
##
## Only use the option table in a normal image
##
-default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
##
## Coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00004000
+default CONFIG_RAMBASE=0x00004000
##
## Load the payload from the ROM
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## Disable the gdb stub by default
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
### End Options.lb
#
#include "cpu/amd/model_fxx/init_cpus.c"
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
#include "southbridge/amd/amd8111/amd8111_enable_rom.c"
#include "northbridge/amd/amdk8/early_ht.c"
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
failover_process(bist, cpu_init_detectedx);
#endif
real_main(bist, cpu_init_detectedx);
// post_code(0x32);
- w83627hf_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ w83627hf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
arch i386 end
#dir /drivers/si/3114
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
if CONFIG_USE_INIT
makerule ./auto.o
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
end
else
makerule ./auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
##
## Build our 16 bit and 32 bit coreboot entry code
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
end
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
end
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_MAX_CPUS
uses CONFIG_MAX_PHYSICAL_CPUS
uses CONFIG_LOGICAL_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
-uses _RAMBASE
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_RAMBASE
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_SERIAL8250
-uses HAVE_INIT_TIMER
+uses CONFIG_HAVE_INIT_TIMER
uses CONFIG_GDB_STUB
uses CONFIG_GDB_STUB
-uses CROSS_COMPILE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
-uses HW_MEM_HOLE_SIZEK
+uses CONFIG_HW_MEM_HOLE_SIZEK
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
uses CONFIG_USE_INIT
uses CONFIG_USE_PRINTK_IN_CAR
###
##
-## ROM_SIZE is the size of boot ROM that this board will use.
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
##
-default ROM_SIZE=524288
+default CONFIG_ROM_SIZE=524288
##
-## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
+## CONFIG_FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
##
-#default FALLBACK_SIZE=131072
+#default CONFIG_FALLBACK_SIZE=131072
#256K
-default FALLBACK_SIZE=0x40000
+default CONFIG_FALLBACK_SIZE=0x40000
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=13
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=13
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
##
## Move the default coreboot cmos range off of AMD RTC registers
##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
+default CONFIG_LB_CKS_RANGE_START=49
+default CONFIG_LB_CKS_RANGE_END=122
+default CONFIG_LB_CKS_LOC=123
##
## Build code for SMP support
default CONFIG_LOGICAL_CPUS=1
#1G memory hole
-default HW_MEM_HOLE_SIZEK=0x100000
+default CONFIG_HW_MEM_HOLE_SIZEK=0x100000
#VGA Console
default CONFIG_CONSOLE_VGA=1
##
## enable CACHE_AS_RAM specifics
##
-default USE_DCACHE_RAM=1
-default DCACHE_RAM_BASE=0xcf000
-default DCACHE_RAM_SIZE=0x1000
+default CONFIG_USE_DCACHE_RAM=1
+default CONFIG_DCACHE_RAM_BASE=0xcf000
+default CONFIG_DCACHE_RAM_SIZE=0x1000
default CONFIG_USE_INIT=0
##
##
## Clean up the motherboard id strings
##
-default MAINBOARD_PART_NUMBER="s2875"
-default MAINBOARD_VENDOR="Tyan"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x10f1
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2875
+default CONFIG_MAINBOARD_PART_NUMBER="s2875"
+default CONFIG_MAINBOARD_VENDOR="Tyan"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x10f1
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2875
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE=0x4000
+default CONFIG_HEAP_SIZE=0x4000
##
## Only use the option table in a normal image
##
-default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
##
## Coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00004000
+default CONFIG_RAMBASE=0x00004000
##
## Load the payload from the ROM
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## Disable the gdb stub by default
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
### End Options.lb
#
#include "cpu/amd/model_fxx/init_cpus.c"
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
#include "southbridge/amd/amd8111/amd8111_enable_rom.c"
#include "northbridge/amd/amdk8/early_ht.c"
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
failover_process(bist, cpu_init_detectedx);
#endif
real_main(bist, cpu_init_detectedx);
init_cpus(cpu_init_detectedx);
}
- w83627hf_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ w83627hf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
arch i386 end
#dir /drivers/si/3114
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
if CONFIG_USE_INIT
makerule ./auto.o
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
end
else
makerule ./auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
##
## Build our 16 bit and 32 bit coreboot entry code
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
end
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
end
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_MAX_CPUS
uses CONFIG_MAX_PHYSICAL_CPUS
uses CONFIG_LOGICAL_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
-uses _RAMBASE
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_RAMBASE
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_SERIAL8250
-uses HAVE_INIT_TIMER
+uses CONFIG_HAVE_INIT_TIMER
uses CONFIG_GDB_STUB
uses CONFIG_GDB_STUB
-uses CROSS_COMPILE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
-uses HW_MEM_HOLE_SIZEK
+uses CONFIG_HW_MEM_HOLE_SIZEK
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
uses CONFIG_USE_INIT
uses CONFIG_USE_PRINTK_IN_CAR
###
##
-## ROM_SIZE is the size of boot ROM that this board will use.
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
##
-default ROM_SIZE=524288
+default CONFIG_ROM_SIZE=524288
##
-## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
+## CONFIG_FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
##
-#default FALLBACK_SIZE=131072
+#default CONFIG_FALLBACK_SIZE=131072
#256K
-default FALLBACK_SIZE=0x40000
+default CONFIG_FALLBACK_SIZE=0x40000
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=13
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=13
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
##
## Move the default coreboot cmos range off of AMD RTC registers
##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
+default CONFIG_LB_CKS_RANGE_START=49
+default CONFIG_LB_CKS_RANGE_END=122
+default CONFIG_LB_CKS_LOC=123
##
## Build code for SMP support
default CONFIG_LOGICAL_CPUS=0
#1G memory hole
-default HW_MEM_HOLE_SIZEK=0x100000
+default CONFIG_HW_MEM_HOLE_SIZEK=0x100000
#VGA Console
default CONFIG_CONSOLE_VGA=1
##
## enable CACHE_AS_RAM specifics
##
-default USE_DCACHE_RAM=1
-default DCACHE_RAM_BASE=0xcf000
-default DCACHE_RAM_SIZE=0x1000
+default CONFIG_USE_DCACHE_RAM=1
+default CONFIG_DCACHE_RAM_BASE=0xcf000
+default CONFIG_DCACHE_RAM_SIZE=0x1000
default CONFIG_USE_INIT=0
##
##
## Clean up the motherboard id strings
##
-default MAINBOARD_PART_NUMBER="S2880"
-default MAINBOARD_VENDOR="Tyan"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x10f1
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2880
+default CONFIG_MAINBOARD_PART_NUMBER="S2880"
+default CONFIG_MAINBOARD_VENDOR="Tyan"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x10f1
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2880
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE=0x4000
+default CONFIG_HEAP_SIZE=0x4000
##
## Only use the option table in a normal image
##
-default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
##
## Coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00004000
+default CONFIG_RAMBASE=0x00004000
##
## Load the payload from the ROM
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## Disable the gdb stub by default
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
### End Options.lb
#
#include "cpu/amd/model_fxx/init_cpus.c"
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
#include "southbridge/amd/amd8111/amd8111_enable_rom.c"
#include "northbridge/amd/amdk8/early_ht.c"
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
failover_process(bist, cpu_init_detectedx);
#endif
real_main(bist, cpu_init_detectedx);
}
- w83627hf_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ w83627hf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
arch i386 end
#dir /drivers/si/3114
object get_bus_conf.o
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
if CONFIG_USE_INIT
makerule ./auto.o
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
end
else
makerule ./auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
##
## Build our 16 bit and 32 bit coreboot entry code
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
end
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
end
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_MAX_CPUS
uses CONFIG_MAX_PHYSICAL_CPUS
uses CONFIG_LOGICAL_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
-uses _RAMBASE
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_RAMBASE
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_SERIAL8250
-uses HAVE_INIT_TIMER
+uses CONFIG_HAVE_INIT_TIMER
uses CONFIG_GDB_STUB
uses CONFIG_GDB_STUB
-uses CROSS_COMPILE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
-uses HW_MEM_HOLE_SIZEK
+uses CONFIG_HW_MEM_HOLE_SIZEK
-uses HT_CHAIN_UNITID_BASE
-uses HT_CHAIN_END_UNITID_BASE
-uses SB_HT_CHAIN_ON_BUS0
-uses SB_HT_CHAIN_UNITID_OFFSET_ONLY
+uses CONFIG_HT_CHAIN_UNITID_BASE
+uses CONFIG_HT_CHAIN_END_UNITID_BASE
+uses CONFIG_SB_HT_CHAIN_ON_BUS0
+uses CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
uses CONFIG_USE_INIT
uses CONFIG_USE_PRINTK_IN_CAR
###
##
-## ROM_SIZE is the size of boot ROM that this board will use.
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
##
-default ROM_SIZE=524288
+default CONFIG_ROM_SIZE=524288
##
-## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
+## CONFIG_FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
##
-#default FALLBACK_SIZE=131072
+#default CONFIG_FALLBACK_SIZE=131072
#256K
-default FALLBACK_SIZE=0x40000
+default CONFIG_FALLBACK_SIZE=0x40000
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=9
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=9
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
##
## Move the default coreboot cmos range off of AMD RTC registers
##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
+default CONFIG_LB_CKS_RANGE_START=49
+default CONFIG_LB_CKS_RANGE_END=122
+default CONFIG_LB_CKS_LOC=123
##
## Build code for SMP support
default CONFIG_LOGICAL_CPUS=1
##HT Unit ID offset, default is 1, the typical one
-default HT_CHAIN_UNITID_BASE=0x0a
+default CONFIG_HT_CHAIN_UNITID_BASE=0x0a
##real SB Unit ID, default is 0x20, mean dont touch it at last
-default HT_CHAIN_END_UNITID_BASE=0x06
+default CONFIG_HT_CHAIN_END_UNITID_BASE=0x06
#make the SB HT chain on bus 0, default is not (0)
-default SB_HT_CHAIN_ON_BUS0=0
+default CONFIG_SB_HT_CHAIN_ON_BUS0=0
##only offset for SB chain?, default is yes(1)
-#default SB_HT_CHAIN_UNITID_OFFSET_ONLY=0
+#default CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY=0
#1G memory hole
-default HW_MEM_HOLE_SIZEK=0x100000
+default CONFIG_HW_MEM_HOLE_SIZEK=0x100000
#VGA Console
default CONFIG_CONSOLE_VGA=1
##
## enable CACHE_AS_RAM specifics
##
-default USE_DCACHE_RAM=1
-default DCACHE_RAM_BASE=0xcf000
-default DCACHE_RAM_SIZE=0x1000
+default CONFIG_USE_DCACHE_RAM=1
+default CONFIG_DCACHE_RAM_BASE=0xcf000
+default CONFIG_DCACHE_RAM_SIZE=0x1000
default CONFIG_USE_INIT=0
##
##
## Clean up the motherboard id strings
##
-default MAINBOARD_PART_NUMBER="s2881"
-default MAINBOARD_VENDOR="Tyan"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x10f1
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2881
+default CONFIG_MAINBOARD_PART_NUMBER="s2881"
+default CONFIG_MAINBOARD_VENDOR="Tyan"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x10f1
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2881
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE=0x4000
+default CONFIG_HEAP_SIZE=0x4000
##
## Only use the option table in a normal image
##
-default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
##
## Coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00004000
+default CONFIG_RAMBASE=0x00004000
##
## Load the payload from the ROM
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## Disable the gdb stub by default
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
### End Options.lb
#
#include "cpu/amd/model_fxx/init_cpus.c"
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
#include "southbridge/amd/amd8111/amd8111_enable_rom.c"
#include "northbridge/amd/amdk8/early_ht.c"
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
failover_process(bist, cpu_init_detectedx);
#endif
real_main(bist, cpu_init_detectedx);
// post_code(0x32);
- w83627hf_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ w83627hf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
dev = dev_find_slot(bus_8111_0, PCI_DEVFN(sysconf.sbdn,0));
if (dev) {
bus_8111_1 = pci_read_config8(dev, PCI_SECONDARY_BUS);
-#if HT_CHAIN_END_UNITID_BASE >= HT_CHAIN_UNITID_BASE
+#if CONFIG_HT_CHAIN_END_UNITID_BASE >= CONFIG_HT_CHAIN_UNITID_BASE
bus_isa = pci_read_config8(dev, PCI_SUBORDINATE_BUS);
bus_isa++;
// printk_debug("bus_isa=%d\n",bus_isa);
dev = dev_find_slot(bus_8131_0, PCI_DEVFN(sbdn3+1,0));
if (dev) {
bus_8131_2 = pci_read_config8(dev, PCI_SECONDARY_BUS);
-#if HT_CHAIN_END_UNITID_BASE < HT_CHAIN_UNITID_BASE
+#if CONFIG_HT_CHAIN_END_UNITID_BASE < CONFIG_HT_CHAIN_UNITID_BASE
bus_isa = pci_read_config8(dev, PCI_SUBORDINATE_BUS);
bus_isa++;
// printk_debug("bus_isa=%d\n",bus_isa);
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
arch i386 end
#dir /drivers/si/3114
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
if CONFIG_USE_INIT
makerule ./auto.o
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
end
else
makerule ./auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
##
## Build our 16 bit and 32 bit coreboot entry code
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
end
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
end
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_MAX_CPUS
uses CONFIG_MAX_PHYSICAL_CPUS
uses CONFIG_LOGICAL_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
-uses _RAMBASE
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_RAMBASE
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_SERIAL8250
-uses HAVE_INIT_TIMER
+uses CONFIG_HAVE_INIT_TIMER
uses CONFIG_GDB_STUB
uses CONFIG_GDB_STUB
-uses CROSS_COMPILE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
-uses HW_MEM_HOLE_SIZEK
+uses CONFIG_HW_MEM_HOLE_SIZEK
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
uses CONFIG_USE_INIT
uses CONFIG_USE_PRINTK_IN_CAR
###
##
-## ROM_SIZE is the size of boot ROM that this board will use.
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
##
-default ROM_SIZE=524288
+default CONFIG_ROM_SIZE=524288
##
-## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
+## CONFIG_FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
##
-#default FALLBACK_SIZE=131072
+#default CONFIG_FALLBACK_SIZE=131072
#256K
-default FALLBACK_SIZE=0x40000
+default CONFIG_FALLBACK_SIZE=0x40000
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=15
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=15
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
##
## Move the default coreboot cmos range off of AMD RTC registers
##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
+default CONFIG_LB_CKS_RANGE_START=49
+default CONFIG_LB_CKS_RANGE_END=122
+default CONFIG_LB_CKS_LOC=123
##
## Build code for SMP support
default CONFIG_LOGICAL_CPUS=1
#1G memory hole
-default HW_MEM_HOLE_SIZEK=0x100000
+default CONFIG_HW_MEM_HOLE_SIZEK=0x100000
#VGA Console
default CONFIG_CONSOLE_VGA=1
##
## enable CACHE_AS_RAM specifics
##
-default USE_DCACHE_RAM=1
-default DCACHE_RAM_BASE=0xcf000
-default DCACHE_RAM_SIZE=0x1000
+default CONFIG_USE_DCACHE_RAM=1
+default CONFIG_DCACHE_RAM_BASE=0xcf000
+default CONFIG_DCACHE_RAM_SIZE=0x1000
default CONFIG_USE_INIT=0
##
##
## Clean up the motherboard id strings
##
-default MAINBOARD_PART_NUMBER="S2882"
-default MAINBOARD_VENDOR="Tyan"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x10f1
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2882
+default CONFIG_MAINBOARD_PART_NUMBER="S2882"
+default CONFIG_MAINBOARD_VENDOR="Tyan"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x10f1
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2882
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE=0x4000
+default CONFIG_HEAP_SIZE=0x4000
##
## Only use the option table in a normal image
##
-default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
##
## Coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00004000
+default CONFIG_RAMBASE=0x00004000
##
## Load the payload from the ROM
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## Disable the gdb stub by default
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
### End Options.lb
#
#include "cpu/amd/model_fxx/init_cpus.c"
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
#include "southbridge/amd/amd8111/amd8111_enable_rom.c"
#include "northbridge/amd/amdk8/early_ht.c"
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
failover_process(bist, cpu_init_detectedx);
#endif
real_main(bist, cpu_init_detectedx);
}
- w83627hf_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ w83627hf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
arch i386 end
#dir /drivers/si/3114
object get_bus_conf.o
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
if CONFIG_USE_INIT
makerule ./auto.o
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
end
else
makerule ./auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
##
## Build our 16 bit and 32 bit coreboot entry code
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
end
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
end
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_MAX_CPUS
uses CONFIG_MAX_PHYSICAL_CPUS
uses CONFIG_LOGICAL_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
-uses _RAMBASE
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_RAMBASE
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_SERIAL8250
-uses HAVE_INIT_TIMER
+uses CONFIG_HAVE_INIT_TIMER
uses CONFIG_GDB_STUB
uses CONFIG_GDB_STUB
-uses CROSS_COMPILE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
-uses HW_MEM_HOLE_SIZEK
+uses CONFIG_HW_MEM_HOLE_SIZEK
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
uses CONFIG_USE_INIT
uses CONFIG_USE_PRINTK_IN_CAR
-uses ENABLE_APIC_EXT_ID
-uses APIC_ID_OFFSET
-uses LIFT_BSP_APIC_ID
+uses CONFIG_ENABLE_APIC_EXT_ID
+uses CONFIG_APIC_ID_OFFSET
+uses CONFIG_LIFT_BSP_APIC_ID
-uses HT_CHAIN_UNITID_BASE
-uses HT_CHAIN_END_UNITID_BASE
-uses SB_HT_CHAIN_ON_BUS0
-uses SB_HT_CHAIN_UNITID_OFFSET_ONLY
+uses CONFIG_HT_CHAIN_UNITID_BASE
+uses CONFIG_HT_CHAIN_END_UNITID_BASE
+uses CONFIG_SB_HT_CHAIN_ON_BUS0
+uses CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY
uses CONFIG_LB_MEM_TOPK
###
##
-## ROM_SIZE is the size of boot ROM that this board will use.
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
##
-default ROM_SIZE=524288
+default CONFIG_ROM_SIZE=524288
##
-## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
+## CONFIG_FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
##
-#default FALLBACK_SIZE=131072
+#default CONFIG_FALLBACK_SIZE=131072
#256K
-default FALLBACK_SIZE=0x40000
+default CONFIG_FALLBACK_SIZE=0x40000
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=11
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=11
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
##
## Move the default coreboot cmos range off of AMD RTC registers
##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
+default CONFIG_LB_CKS_RANGE_START=49
+default CONFIG_LB_CKS_RANGE_END=122
+default CONFIG_LB_CKS_LOC=123
##
## Build code for SMP support
default CONFIG_LOGICAL_CPUS=1
##HT Unit ID offset, default is 1, the typical one
-default HT_CHAIN_UNITID_BASE=0x0a
+default CONFIG_HT_CHAIN_UNITID_BASE=0x0a
##real SB Unit ID, default is 0x20, mean dont touch it at last
-default HT_CHAIN_END_UNITID_BASE=0x06
+default CONFIG_HT_CHAIN_END_UNITID_BASE=0x06
#make the SB HT chain on bus 0, default is not (0)
-default SB_HT_CHAIN_ON_BUS0=2
+default CONFIG_SB_HT_CHAIN_ON_BUS0=2
##only offset for SB chain?, default is yes(1)
-#default SB_HT_CHAIN_UNITID_OFFSET_ONLY=0
+#default CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY=0
#1G memory hole
-default HW_MEM_HOLE_SIZEK=0x100000
+default CONFIG_HW_MEM_HOLE_SIZEK=0x100000
#VGA Console
default CONFIG_CONSOLE_VGA=1
##
## enable CACHE_AS_RAM specifics
##
-default USE_DCACHE_RAM=1
-default DCACHE_RAM_BASE=0xcf000
-default DCACHE_RAM_SIZE=0x1000
+default CONFIG_USE_DCACHE_RAM=1
+default CONFIG_DCACHE_RAM_BASE=0xcf000
+default CONFIG_DCACHE_RAM_SIZE=0x1000
default CONFIG_USE_INIT=0
-default ENABLE_APIC_EXT_ID=1
-default APIC_ID_OFFSET=0x10
-default LIFT_BSP_APIC_ID=0
+default CONFIG_ENABLE_APIC_EXT_ID=1
+default CONFIG_APIC_ID_OFFSET=0x10
+default CONFIG_LIFT_BSP_APIC_ID=0
##
## Build code to setup a generic IOAPIC
##
## Clean up the motherboard id strings
##
-default MAINBOARD_PART_NUMBER="s2885"
-default MAINBOARD_VENDOR="Tyan"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x10f1
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2885
+default CONFIG_MAINBOARD_PART_NUMBER="s2885"
+default CONFIG_MAINBOARD_VENDOR="Tyan"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x10f1
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2885
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE=0x4000
+default CONFIG_HEAP_SIZE=0x4000
##
## Only use the option table in a normal image
##
-default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
##
## Coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00004000
+default CONFIG_RAMBASE=0x00004000
##
## Load the payload from the ROM
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## Disable the gdb stub by default
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
### End Options.lb
#
#include "cpu/amd/model_fxx/init_cpus.c"
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
#include "southbridge/amd/amd8111/amd8111_enable_rom.c"
#include "northbridge/amd/amdk8/early_ht.c"
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
failover_process(bist, cpu_init_detectedx);
#endif
real_main(bist, cpu_init_detectedx);
// post_code(0x32);
- w83627hf_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ w83627hf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
-// dump_mem(DCACHE_RAM_BASE+DCACHE_RAM_SIZE-0x200, DCACHE_RAM_BASE+DCACHE_RAM_SIZE);
+// dump_mem(CONFIG_DCACHE_RAM_BASE+CONFIG_DCACHE_RAM_SIZE-0x200, CONFIG_DCACHE_RAM_BASE+CONFIG_DCACHE_RAM_SIZE);
/* Halt if there was a built in self test failure */
report_bist_failure(bist);
dev = dev_find_slot(bus_8111_0, PCI_DEVFN(sysconf.sbdn,0));
if (dev) {
bus_8111_1 = pci_read_config8(dev, PCI_SECONDARY_BUS);
-#if HT_CHAIN_END_UNITID_BASE >= HT_CHAIN_UNITID_BASE
+#if CONFIG_HT_CHAIN_END_UNITID_BASE >= CONFIG_HT_CHAIN_UNITID_BASE
bus_isa = pci_read_config8(dev, PCI_SUBORDINATE_BUS);
bus_isa++;
// printk_debug("bus_isa=%d\n",bus_isa);
dev = dev_find_slot(bus_8131_0, PCI_DEVFN(sbdn3+1,0));
if (dev) {
bus_8131_2 = pci_read_config8(dev, PCI_SECONDARY_BUS);
-#if HT_CHAIN_END_UNITID_BASE < HT_CHAIN_UNITID_BASE
+#if CONFIG_HT_CHAIN_END_UNITID_BASE < CONFIG_HT_CHAIN_UNITID_BASE
bus_isa = pci_read_config8(dev, PCI_SUBORDINATE_BUS);
bus_isa++;
// printk_debug("bus_isa=%d\n",bus_isa);
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
default CONFIG_ROM_PAYLOAD = 1
#needed by irq_tables and mptable and acpi_tables
object get_bus_conf.o
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
#object reset.o
-if HAVE_ACPI_TABLES
+if CONFIG_HAVE_ACPI_TABLES
object acpi_tables.o
makerule dsdt.c
- depends "$(MAINBOARD)/dsdt.dsl"
- action "iasl -p $(CURDIR)/dsdt -tc $(MAINBOARD)/dsdt.dsl"
+ depends "$(CONFIG_MAINBOARD)/dsdt.dsl"
+ action "iasl -p $(CURDIR)/dsdt -tc $(CONFIG_MAINBOARD)/dsdt.dsl"
action "mv dsdt.hex dsdt.c"
end
object ./dsdt.o
if CONFIG_USE_INIT
makerule ./auto.o
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
end
else
makerule ./auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
##
## Build our 16 bit and 32 bit coreboot entry code
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
end
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
##
## ROMSTRAP table for CK804
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit southbridge/nvidia/ck804/romstrap.inc
ldscript /southbridge/nvidia/ck804/romstrap.lds
end
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
end
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_MAX_CPUS
uses CONFIG_MAX_PHYSICAL_CPUS
uses CONFIG_LOGICAL_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses HAVE_ACPI_TABLES
-uses HAVE_ACPI_RESUME
-uses HAVE_LOW_TABLES
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_HAVE_ACPI_TABLES
+uses CONFIG_HAVE_ACPI_RESUME
+uses CONFIG_HAVE_LOW_TABLES
uses CONFIG_MULTIBOOT
-uses HAVE_SMI_HANDLER
-uses MAINBOARD
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_HAVE_SMI_HANDLER
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
-uses _RAMBASE
+uses CONFIG_RAMBASE
uses CONFIG_GDB_STUB
-uses CROSS_COMPILE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_SERIAL8250
uses CONFIG_CONSOLE_BTEXT
-uses HAVE_INIT_TIMER
+uses CONFIG_HAVE_INIT_TIMER
uses CONFIG_GDB_STUB
uses CONFIG_CONSOLE_VGA
uses CONFIG_VGA_ROM_RUN
uses CONFIG_PCI_ROM_RUN
-uses HW_MEM_HOLE_SIZEK
+uses CONFIG_HW_MEM_HOLE_SIZEK
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
uses CONFIG_USE_INIT
uses CONFIG_USE_PRINTK_IN_CAR
-uses ENABLE_APIC_EXT_ID
-uses APIC_ID_OFFSET
-uses LIFT_BSP_APIC_ID
+uses CONFIG_ENABLE_APIC_EXT_ID
+uses CONFIG_APIC_ID_OFFSET
+uses CONFIG_LIFT_BSP_APIC_ID
uses CONFIG_PCI_64BIT_PREF_MEM
-uses HT_CHAIN_UNITID_BASE
-uses HT_CHAIN_END_UNITID_BASE
-uses SB_HT_CHAIN_ON_BUS0
-uses SB_HT_CHAIN_UNITID_OFFSET_ONLY
+uses CONFIG_HT_CHAIN_UNITID_BASE
+uses CONFIG_HT_CHAIN_END_UNITID_BASE
+uses CONFIG_SB_HT_CHAIN_ON_BUS0
+uses CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY
uses CONFIG_LB_MEM_TOPK
-## ROM_SIZE is the size of boot ROM that this board will use.
-default ROM_SIZE=512*1024
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
+default CONFIG_ROM_SIZE=512*1024
##
-## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
+## CONFIG_FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
##
-#default FALLBACK_SIZE=131072
+#default CONFIG_FALLBACK_SIZE=131072
#256K
-default FALLBACK_SIZE=0x40000
+default CONFIG_FALLBACK_SIZE=0x40000
###
### Build options
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
##
## Build SMI handler
##
-default HAVE_SMI_HANDLER=0
+default CONFIG_HAVE_SMI_HANDLER=0
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=11
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=11
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
##
## Build code to provide ACPI support
##
-default HAVE_ACPI_TABLES=1
-default HAVE_LOW_TABLES=1
+default CONFIG_HAVE_ACPI_TABLES=1
+default CONFIG_HAVE_LOW_TABLES=1
default CONFIG_MULTIBOOT=0
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
##
## Move the default coreboot cmos range off of AMD RTC registers
##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
+default CONFIG_LB_CKS_RANGE_START=49
+default CONFIG_LB_CKS_RANGE_END=122
+default CONFIG_LB_CKS_LOC=123
#VGA Console
default CONFIG_CONSOLE_VGA=1
default CONFIG_LOGICAL_CPUS=1
#1G memory hole
-default HW_MEM_HOLE_SIZEK=0x100000
+default CONFIG_HW_MEM_HOLE_SIZEK=0x100000
##HT Unit ID offset, default is 1, the typical one
-default HT_CHAIN_UNITID_BASE=0x0
+default CONFIG_HT_CHAIN_UNITID_BASE=0x0
##real SB Unit ID, default is 0x20, mean dont touch it at last
-#default HT_CHAIN_END_UNITID_BASE=0x0
+#default CONFIG_HT_CHAIN_END_UNITID_BASE=0x0
#make the SB HT chain on bus 0, default is not (0)
-default SB_HT_CHAIN_ON_BUS0=2
+default CONFIG_SB_HT_CHAIN_ON_BUS0=2
##only offset for SB chain?, default is yes(1)
-#default SB_HT_CHAIN_UNITID_OFFSET_ONLY=0
+#default CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY=0
#BTEXT Console
#default CONFIG_CONSOLE_BTEXT=1
##
## enable CACHE_AS_RAM specifics
##
-default USE_DCACHE_RAM=1
-default DCACHE_RAM_BASE=0xcf000
-default DCACHE_RAM_SIZE=0x1000
+default CONFIG_USE_DCACHE_RAM=1
+default CONFIG_DCACHE_RAM_BASE=0xcf000
+default CONFIG_DCACHE_RAM_SIZE=0x1000
default CONFIG_USE_INIT=0
-default ENABLE_APIC_EXT_ID=0
-default APIC_ID_OFFSET=0x10
-default LIFT_BSP_APIC_ID=0
+default CONFIG_ENABLE_APIC_EXT_ID=0
+default CONFIG_APIC_ID_OFFSET=0x10
+default CONFIG_LIFT_BSP_APIC_ID=0
#default CONFIG_PCI_64BIT_PREF_MEM=1
##
## Clean up the motherboard id strings
##
-default MAINBOARD_PART_NUMBER="s2891"
-default MAINBOARD_VENDOR="Tyan"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x10f1
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2891
+default CONFIG_MAINBOARD_PART_NUMBER="s2891"
+default CONFIG_MAINBOARD_VENDOR="Tyan"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x10f1
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2891
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE=0x4000
+default CONFIG_HEAP_SIZE=0x4000
##
## Only use the option table in a normal image
##
-default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
##
## Coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00004000
+default CONFIG_RAMBASE=0x00004000
##
## Load the payload from the ROM
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## Disable the gdb stub by default
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
### End Options.lb
#
#include "cpu/amd/model_fxx/init_cpus.c"
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
#include "southbridge/nvidia/ck804/ck804_enable_rom.c"
#include "northbridge/amd/amdk8/early_ht.c"
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
failover_process(bist, cpu_init_detectedx);
#endif
real_main(bist, cpu_init_detectedx);
// post_code(0x32);
- w83627hf_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ w83627hf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
default CONFIG_ROM_PAYLOAD = 1
#needed by irq_tables and mptable and acpi_tables
object get_bus_conf.o
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
#object reset.o
-if HAVE_ACPI_TABLES
+if CONFIG_HAVE_ACPI_TABLES
object acpi_tables.o
makerule dsdt.c
- depends "$(MAINBOARD)/dsdt.dsl"
- action "iasl -p $(CURDIR)/dsdt -tc $(MAINBOARD)/dsdt.dsl"
+ depends "$(CONFIG_MAINBOARD)/dsdt.dsl"
+ action "iasl -p $(CURDIR)/dsdt -tc $(CONFIG_MAINBOARD)/dsdt.dsl"
action "mv dsdt.hex dsdt.c"
end
object ./dsdt.o
if CONFIG_USE_INIT
makerule ./auto.o
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
end
else
makerule ./auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
##
## Build our 16 bit and 32 bit coreboot entry code
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
end
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
##
## ROMSTRAP table for CK804
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit southbridge/nvidia/ck804/romstrap.inc
ldscript /southbridge/nvidia/ck804/romstrap.lds
end
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
end
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_MAX_CPUS
uses CONFIG_MAX_PHYSICAL_CPUS
uses CONFIG_LOGICAL_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses HAVE_ACPI_TABLES
-uses HAVE_ACPI_RESUME
-uses HAVE_LOW_TABLES
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_HAVE_ACPI_TABLES
+uses CONFIG_HAVE_ACPI_RESUME
+uses CONFIG_HAVE_LOW_TABLES
uses CONFIG_MULTIBOOT
-uses HAVE_SMI_HANDLER
-uses MAINBOARD
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_HAVE_SMI_HANDLER
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
-uses _RAMBASE
+uses CONFIG_RAMBASE
uses CONFIG_GDB_STUB
-uses CROSS_COMPILE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_SERIAL8250
uses CONFIG_CONSOLE_BTEXT
-uses HAVE_INIT_TIMER
+uses CONFIG_HAVE_INIT_TIMER
uses CONFIG_GDB_STUB
uses CONFIG_CONSOLE_VGA
uses CONFIG_VGA_ROM_RUN
uses CONFIG_PCI_ROM_RUN
-uses HW_MEM_HOLE_SIZEK
+uses CONFIG_HW_MEM_HOLE_SIZEK
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
uses CONFIG_USE_INIT
uses CONFIG_USE_PRINTK_IN_CAR
-uses HT_CHAIN_UNITID_BASE
-uses HT_CHAIN_END_UNITID_BASE
-uses SB_HT_CHAIN_ON_BUS0
-uses SB_HT_CHAIN_UNITID_OFFSET_ONLY
+uses CONFIG_HT_CHAIN_UNITID_BASE
+uses CONFIG_HT_CHAIN_END_UNITID_BASE
+uses CONFIG_SB_HT_CHAIN_ON_BUS0
+uses CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY
uses CONFIG_LB_MEM_TOPK
-## ROM_SIZE is the size of boot ROM that this board will use.
-default ROM_SIZE=1024*1024
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
+default CONFIG_ROM_SIZE=1024*1024
##
-## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
+## CONFIG_FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
##
-#default FALLBACK_SIZE=131072
+#default CONFIG_FALLBACK_SIZE=131072
#256K
-default FALLBACK_SIZE=0x40000
+default CONFIG_FALLBACK_SIZE=0x40000
###
### Build options
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
##
## Build SMI handler
##
-default HAVE_SMI_HANDLER=0
+default CONFIG_HAVE_SMI_HANDLER=0
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=11
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=11
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
##
## Build code to provide ACPI support
##
-default HAVE_ACPI_TABLES=1
-default HAVE_LOW_TABLES=1
+default CONFIG_HAVE_ACPI_TABLES=1
+default CONFIG_HAVE_LOW_TABLES=1
default CONFIG_MULTIBOOT=0
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
##
## Move the default coreboot cmos range off of AMD RTC registers
##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
+default CONFIG_LB_CKS_RANGE_START=49
+default CONFIG_LB_CKS_RANGE_END=122
+default CONFIG_LB_CKS_LOC=123
#VGA Console
default CONFIG_CONSOLE_VGA=1
default CONFIG_LOGICAL_CPUS=1
#1G memory hole
-default HW_MEM_HOLE_SIZEK=0x100000
+default CONFIG_HW_MEM_HOLE_SIZEK=0x100000
##HT Unit ID offset, default is 1, the typical one
-default HT_CHAIN_UNITID_BASE=0x0
+default CONFIG_HT_CHAIN_UNITID_BASE=0x0
##real SB Unit ID, default is 0x20, mean dont touch it at last
-#default HT_CHAIN_END_UNITID_BASE=0x0
+#default CONFIG_HT_CHAIN_END_UNITID_BASE=0x0
#make the SB HT chain on bus 0, default is not (0)
-default SB_HT_CHAIN_ON_BUS0=2
+default CONFIG_SB_HT_CHAIN_ON_BUS0=2
##only offset for SB chain?, default is yes(1)
-default SB_HT_CHAIN_UNITID_OFFSET_ONLY=0
+default CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY=0
#BTEXT Console
#default CONFIG_CONSOLE_BTEXT=1
##
## enable CACHE_AS_RAM specifics
##
-default USE_DCACHE_RAM=1
-default DCACHE_RAM_BASE=0xcf000
-default DCACHE_RAM_SIZE=0x1000
+default CONFIG_USE_DCACHE_RAM=1
+default CONFIG_DCACHE_RAM_BASE=0xcf000
+default CONFIG_DCACHE_RAM_SIZE=0x1000
default CONFIG_USE_INIT=0
##
## Clean up the motherboard id strings
##
-default MAINBOARD_PART_NUMBER="s2892"
-default MAINBOARD_VENDOR="Tyan"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x10f1
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2892
+default CONFIG_MAINBOARD_PART_NUMBER="s2892"
+default CONFIG_MAINBOARD_VENDOR="Tyan"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x10f1
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2892
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE=0x4000
+default CONFIG_HEAP_SIZE=0x4000
##
## Only use the option table in a normal image
##
-default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
##
## Coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00004000
+default CONFIG_RAMBASE=0x00004000
##
## Load the payload from the ROM
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## Disable the gdb stub by default
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
### End Options.lb
#
#include "cpu/amd/model_fxx/init_cpus.c"
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
#include "southbridge/nvidia/ck804/ck804_enable_rom.c"
#include "northbridge/amd/amdk8/early_ht.c"
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
failover_process(bist, cpu_init_detectedx);
#endif
real_main(bist, cpu_init_detectedx);
// post_code(0x32);
- w83627hf_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ w83627hf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/failovercalculation.lb
arch i386 end
#needed by irq_tables and mptable and acpi_tables
object get_bus_conf.o
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
#object reset.o
-if HAVE_ACPI_TABLES
+if CONFIG_HAVE_ACPI_TABLES
object acpi_tables.o
makerule dsdt.c
- depends "$(MAINBOARD)/dsdt.dsl"
- action "iasl -p $(CURDIR)/dsdt -tc $(MAINBOARD)/dsdt.dsl"
+ depends "$(CONFIG_MAINBOARD)/dsdt.dsl"
+ action "iasl -p $(CURDIR)/dsdt -tc $(CONFIG_MAINBOARD)/dsdt.dsl"
action "mv dsdt.hex dsdt.c"
end
object ./dsdt.o
if CONFIG_USE_INIT
makerule ./auto.o
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
end
else
makerule ./auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
##
## Build our 16 bit and 32 bit coreboot entry code
##
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
end
##
## Build our reset vector (This is where coreboot is entered)
##
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
ldscript /cpu/x86/32bit/reset32.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
##
## ROMSTRAP table for CK804
##
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
mainboardinit southbridge/nvidia/ck804/romstrap.inc
ldscript /southbridge/nvidia/ck804/romstrap.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
mainboardinit southbridge/nvidia/ck804/romstrap.inc
ldscript /southbridge/nvidia/ck804/romstrap.lds
end
### Things are delicate and we test to see if we should
### failover to another image.
###
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
ldscript /arch/i386/lib/failover_failover.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
end
end
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses USE_FAILOVER_IMAGE
-uses HAVE_FAILOVER_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_USE_FAILOVER_IMAGE
+uses CONFIG_HAVE_FAILOVER_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_MAX_CPUS
uses CONFIG_MAX_PHYSICAL_CPUS
uses CONFIG_LOGICAL_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses FAILOVER_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_FAILOVER_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses HAVE_ACPI_TABLES
-uses HAVE_ACPI_RESUME
-uses HAVE_LOW_TABLES
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_HAVE_ACPI_TABLES
+uses CONFIG_HAVE_ACPI_RESUME
+uses CONFIG_HAVE_LOW_TABLES
uses CONFIG_MULTIBOOT
-uses HAVE_SMI_HANDLER
-uses MAINBOARD
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_HAVE_SMI_HANDLER
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
-uses _RAMBASE
+uses CONFIG_RAMBASE
uses CONFIG_GDB_STUB
-uses CROSS_COMPILE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_SERIAL8250
-uses HAVE_INIT_TIMER
+uses CONFIG_HAVE_INIT_TIMER
uses CONFIG_GDB_STUB
uses CONFIG_CONSOLE_VGA
uses CONFIG_VGA_ROM_RUN
uses CONFIG_PCI_ROM_RUN
-uses HW_MEM_HOLE_SIZEK
-uses K8_HT_FREQ_1G_SUPPORT
+uses CONFIG_HW_MEM_HOLE_SIZEK
+uses CONFIG_K8_HT_FREQ_1G_SUPPORT
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
uses CONFIG_USE_INIT
uses CONFIG_USE_PRINTK_IN_CAR
-uses SERIAL_CPU_INIT
+uses CONFIG_SERIAL_CPU_INIT
-uses ENABLE_APIC_EXT_ID
-uses APIC_ID_OFFSET
-uses LIFT_BSP_APIC_ID
+uses CONFIG_ENABLE_APIC_EXT_ID
+uses CONFIG_APIC_ID_OFFSET
+uses CONFIG_LIFT_BSP_APIC_ID
-uses HT_CHAIN_UNITID_BASE
-uses HT_CHAIN_END_UNITID_BASE
-uses SB_HT_CHAIN_ON_BUS0
-uses SB_HT_CHAIN_UNITID_OFFSET_ONLY
+uses CONFIG_HT_CHAIN_UNITID_BASE
+uses CONFIG_HT_CHAIN_END_UNITID_BASE
+uses CONFIG_SB_HT_CHAIN_ON_BUS0
+uses CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY
uses CONFIG_LB_MEM_TOPK
-## ROM_SIZE is the size of boot ROM that this board will use.
-default ROM_SIZE=1024*1024
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
+default CONFIG_ROM_SIZE=1024*1024
##
-## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
+## CONFIG_FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
##
-#default FALLBACK_SIZE=131072
-#default FALLBACK_SIZE=0x40000
+#default CONFIG_FALLBACK_SIZE=131072
+#default CONFIG_FALLBACK_SIZE=0x40000
#FALLBACK: 256K-4K
-default FALLBACK_SIZE=0x3f000
+default CONFIG_FALLBACK_SIZE=0x3f000
#FAILOVER: 4K
-default FAILOVER_SIZE=0x01000
+default CONFIG_FAILOVER_SIZE=0x01000
#more 1M for pgtbl
default CONFIG_LB_MEM_TOPK=2048
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
-default HAVE_FAILOVER_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FAILOVER_BOOT=1
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
##
## Build SMI handler
##
-default HAVE_SMI_HANDLER=0
+default CONFIG_HAVE_SMI_HANDLER=0
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=11
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=11
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
##
## Build code to provide ACPI support
##
-default HAVE_ACPI_TABLES=1
-default HAVE_LOW_TABLES=1
+default CONFIG_HAVE_ACPI_TABLES=1
+default CONFIG_HAVE_LOW_TABLES=1
default CONFIG_MULTIBOOT=0
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
##
## Move the default coreboot cmos range off of AMD RTC registers
##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
+default CONFIG_LB_CKS_RANGE_START=49
+default CONFIG_LB_CKS_RANGE_END=122
+default CONFIG_LB_CKS_LOC=123
#VGA Console
default CONFIG_CONSOLE_VGA=1
default CONFIG_MAX_PHYSICAL_CPUS=2
default CONFIG_LOGICAL_CPUS=1
-default SERIAL_CPU_INIT=0
+default CONFIG_SERIAL_CPU_INIT=0
#1G memory hole
-default HW_MEM_HOLE_SIZEK=0x100000
+default CONFIG_HW_MEM_HOLE_SIZEK=0x100000
##HT Unit ID offset, default is 1, the typical one
-default HT_CHAIN_UNITID_BASE=0x0
+default CONFIG_HT_CHAIN_UNITID_BASE=0x0
##real SB Unit ID, default is 0x20, mean dont touch it at last
-#default HT_CHAIN_END_UNITID_BASE=0x0
+#default CONFIG_HT_CHAIN_END_UNITID_BASE=0x0
#make the SB HT chain on bus 0, default is not (0)
-default SB_HT_CHAIN_ON_BUS0=2
+default CONFIG_SB_HT_CHAIN_ON_BUS0=2
##only offset for SB chain?, default is yes(1)
-default SB_HT_CHAIN_UNITID_OFFSET_ONLY=0
+default CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY=0
#Opteron K8 1G HT Support
-default K8_HT_FREQ_1G_SUPPORT=1
+default CONFIG_K8_HT_FREQ_1G_SUPPORT=1
#VGA Console
default CONFIG_CONSOLE_VGA=1
##
## enable CACHE_AS_RAM specifics
##
-default USE_DCACHE_RAM=1
-default DCACHE_RAM_BASE=0xcf000
-default DCACHE_RAM_SIZE=0x1000
+default CONFIG_USE_DCACHE_RAM=1
+default CONFIG_DCACHE_RAM_BASE=0xcf000
+default CONFIG_DCACHE_RAM_SIZE=0x1000
default CONFIG_USE_INIT=0
-default ENABLE_APIC_EXT_ID=0
-default APIC_ID_OFFSET=0x10
-default LIFT_BSP_APIC_ID=0
+default CONFIG_ENABLE_APIC_EXT_ID=0
+default CONFIG_APIC_ID_OFFSET=0x10
+default CONFIG_LIFT_BSP_APIC_ID=0
##
##
## Clean up the motherboard id strings
##
-default MAINBOARD_PART_NUMBER="s2895"
-default MAINBOARD_VENDOR="Tyan"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x10f1
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2895
+default CONFIG_MAINBOARD_PART_NUMBER="s2895"
+default CONFIG_MAINBOARD_VENDOR="Tyan"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x10f1
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2895
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE=0x4000
+default CONFIG_HEAP_SIZE=0x4000
##
## Only use the option table in a normal image
##
-default USE_OPTION_TABLE = (!USE_FALLBACK_IMAGE) && (!USE_FAILOVER_IMAGE )
+default CONFIG_USE_OPTION_TABLE = (!CONFIG_USE_FALLBACK_IMAGE) && (!CONFIG_USE_FAILOVER_IMAGE )
##
## Coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00100000
+default CONFIG_RAMBASE=0x00100000
##
## Load the payload from the ROM
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## Disable the gdb stub by default
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
### End Options.lb
#
#include "option_table.h"
#include "pc80/mc146818rtc_early.c"
-#if USE_FAILOVER_IMAGE==0
+#if CONFIG_USE_FAILOVER_IMAGE==0
#include "pc80/serial.c"
#include "arch/i386/lib/console.c"
#include "ram/ramtest.c"
#define SUPERIO_GPIO_IO_BASE 0x400
-#if USE_FAILOVER_IMAGE==0
+#if CONFIG_USE_FAILOVER_IMAGE==0
#include "cpu/x86/bist.h"
#endif
-#if ((HAVE_FAILOVER_BOOT==1) && (USE_FAILOVER_IMAGE == 1)) || ((HAVE_FAILOVER_BOOT==0) && (USE_FALLBACK_IMAGE == 1))
+#if ((CONFIG_HAVE_FAILOVER_BOOT==1) && (CONFIG_USE_FAILOVER_IMAGE == 1)) || ((CONFIG_HAVE_FAILOVER_BOOT==0) && (CONFIG_USE_FALLBACK_IMAGE == 1))
#include "southbridge/nvidia/ck804/ck804_enable_rom.c"
#include "northbridge/amd/amdk8/early_ht.c"
fallback_image:
// post_code(0x25);
-#if HAVE_FAILOVER_BOOT==1
+#if CONFIG_HAVE_FAILOVER_BOOT==1
__asm__ volatile ("jmp __fallback_image"
: /* outputs */
: "a" (bist), "b" (cpu_init_detectedx) /* inputs */
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
-#if HAVE_FAILOVER_BOOT==1
- #if USE_FAILOVER_IMAGE==1
+#if CONFIG_HAVE_FAILOVER_BOOT==1
+ #if CONFIG_USE_FAILOVER_IMAGE==1
failover_process(bist, cpu_init_detectedx);
#else
real_main(bist, cpu_init_detectedx);
#endif
#else
- #if USE_FALLBACK_IMAGE == 1
+ #if CONFIG_USE_FALLBACK_IMAGE == 1
failover_process(bist, cpu_init_detectedx);
#endif
real_main(bist, cpu_init_detectedx);
#endif
}
-#if USE_FAILOVER_IMAGE==0
+#if CONFIG_USE_FAILOVER_IMAGE==0
void real_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
// post_code(0x32);
- lpc47b397_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ lpc47b397_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/failovercalculation.lb
arch i386 end
#needed by irq_tables and mptable and acpi_tables
object get_bus_conf.o
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
#object reset.o
if CONFIG_USE_INIT
makerule ./cache_as_ram_auto.o
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
end
else
makerule ./cache_as_ram_auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
end
-if USE_FAILOVER_IMAGE
+if CONFIG_USE_FAILOVER_IMAGE
else
if CONFIG_AP_CODE_IN_CAR
makerule ./apc_auto.o
- depends "$(MAINBOARD)/apc_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/apc_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/apc_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/apc_auto.c -o $@"
end
ldscript /arch/i386/init/ldscript_apc.lb
end
##
## Build our 16 bit and 32 bit coreboot entry code
##
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
end
##
## Build our reset vector (This is where coreboot is entered)
##
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
ldscript /cpu/x86/32bit/reset32.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
##
## ROMSTRAP table for MCP55
##
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
mainboardinit southbridge/nvidia/mcp55/romstrap.inc
ldscript /southbridge/nvidia/mcp55/romstrap.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
mainboardinit southbridge/nvidia/mcp55/romstrap.inc
ldscript /southbridge/nvidia/mcp55/romstrap.lds
end
### Things are delicate and we test to see if we should
### failover to another image.
###
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
ldscript /arch/i386/lib/failover_failover.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
end
end
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses HAVE_ACPI_TABLES
-uses HAVE_ACPI_RESUME
-uses ACPI_SSDTX_NUM
-uses USE_FALLBACK_IMAGE
-uses USE_FAILOVER_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_FAILOVER_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_HAVE_ACPI_TABLES
+uses CONFIG_HAVE_ACPI_RESUME
+uses CONFIG_ACPI_SSDTX_NUM
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_USE_FAILOVER_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_FAILOVER_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_MAX_CPUS
uses CONFIG_MAX_PHYSICAL_CPUS
uses CONFIG_LOGICAL_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses FAILOVER_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_FAILOVER_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_NRV2B
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
-uses _RAMBASE
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_RAMBASE
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_SERIAL8250
-uses HAVE_INIT_TIMER
+uses CONFIG_HAVE_INIT_TIMER
uses CONFIG_GDB_STUB
uses CONFIG_GDB_STUB
-uses CROSS_COMPILE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
uses CONFIG_CONSOLE_VGA
uses CONFIG_USBDEBUG_DIRECT
uses CONFIG_PCI_ROM_RUN
-uses HW_MEM_HOLE_SIZEK
-uses HW_MEM_HOLE_SIZE_AUTO_INC
-uses K8_HT_FREQ_1G_SUPPORT
-
-uses HT_CHAIN_UNITID_BASE
-uses HT_CHAIN_END_UNITID_BASE
-uses SB_HT_CHAIN_ON_BUS0
-uses SB_HT_CHAIN_UNITID_OFFSET_ONLY
-
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
-uses DCACHE_RAM_GLOBAL_VAR_SIZE
+uses CONFIG_HW_MEM_HOLE_SIZEK
+uses CONFIG_HW_MEM_HOLE_SIZE_AUTO_INC
+uses CONFIG_K8_HT_FREQ_1G_SUPPORT
+
+uses CONFIG_HT_CHAIN_UNITID_BASE
+uses CONFIG_HT_CHAIN_END_UNITID_BASE
+uses CONFIG_SB_HT_CHAIN_ON_BUS0
+uses CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY
+
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
+uses CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE
uses CONFIG_USE_INIT
-uses SERIAL_CPU_INIT
+uses CONFIG_SERIAL_CPU_INIT
-uses ENABLE_APIC_EXT_ID
-uses APIC_ID_OFFSET
-uses LIFT_BSP_APIC_ID
+uses CONFIG_ENABLE_APIC_EXT_ID
+uses CONFIG_APIC_ID_OFFSET
+uses CONFIG_LIFT_BSP_APIC_ID
uses CONFIG_PCI_64BIT_PREF_MEM
uses CONFIG_AP_CODE_IN_CAR
-uses MEM_TRAIN_SEQ
+uses CONFIG_MEM_TRAIN_SEQ
-uses WAIT_BEFORE_CPUS_INIT
+uses CONFIG_WAIT_BEFORE_CPUS_INIT
uses CONFIG_USE_PRINTK_IN_CAR
###
##
-## ROM_SIZE is the size of boot ROM that this board will use.
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
##
-default ROM_SIZE=524288
-#default ROM_SIZE=0x100000
+default CONFIG_ROM_SIZE=524288
+#default CONFIG_ROM_SIZE=0x100000
##
-## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
+## CONFIG_FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
##
-#default FALLBACK_SIZE=131072
-#default FALLBACK_SIZE=0x40000
+#default CONFIG_FALLBACK_SIZE=131072
+#default CONFIG_FALLBACK_SIZE=0x40000
#FALLBACK: 256K-4K
-default FALLBACK_SIZE=0x3f000
+default CONFIG_FALLBACK_SIZE=0x3f000
#FAILOVER: 4K
-default FAILOVER_SIZE=0x01000
+default CONFIG_FAILOVER_SIZE=0x01000
#more 1M for pgtbl
default CONFIG_LB_MEM_TOPK=2048
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
-default HAVE_FAILOVER_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FAILOVER_BOOT=1
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=11
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=11
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
## ACPI tables will be included
-default HAVE_ACPI_TABLES=0
+default CONFIG_HAVE_ACPI_TABLES=0
## extra SSDT num
-default ACPI_SSDTX_NUM=3
+default CONFIG_ACPI_SSDTX_NUM=3
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
##
## Move the default coreboot cmos range off of AMD RTC registers
##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
+default CONFIG_LB_CKS_RANGE_START=49
+default CONFIG_LB_CKS_RANGE_END=122
+default CONFIG_LB_CKS_LOC=123
##
## Build code for SMP support
default CONFIG_MAX_PHYSICAL_CPUS=2
default CONFIG_LOGICAL_CPUS=1
-#default SERIAL_CPU_INIT=0
+#default CONFIG_SERIAL_CPU_INIT=0
-default ENABLE_APIC_EXT_ID=0
-default APIC_ID_OFFSET=0x10
-default LIFT_BSP_APIC_ID=1
+default CONFIG_ENABLE_APIC_EXT_ID=0
+default CONFIG_APIC_ID_OFFSET=0x10
+default CONFIG_LIFT_BSP_APIC_ID=1
#memory hole size, 0 mean disable, others will enable the hole, at that case if it is small than mmio_basek, it will use mmio_basek instead.
#2G
-#default HW_MEM_HOLE_SIZEK=0x200000
+#default CONFIG_HW_MEM_HOLE_SIZEK=0x200000
#1G
-default HW_MEM_HOLE_SIZEK=0x100000
+default CONFIG_HW_MEM_HOLE_SIZEK=0x100000
#512M
-#default HW_MEM_HOLE_SIZEK=0x80000
+#default CONFIG_HW_MEM_HOLE_SIZEK=0x80000
#make auto increase hole size to avoid hole_startk equal to basek so as to make some kernel happy
-#default HW_MEM_HOLE_SIZE_AUTO_INC=1
+#default CONFIG_HW_MEM_HOLE_SIZE_AUTO_INC=1
#Opteron K8 1G HT Support
-default K8_HT_FREQ_1G_SUPPORT=1
+default CONFIG_K8_HT_FREQ_1G_SUPPORT=1
#VGA Console
default CONFIG_CONSOLE_VGA=1
#default CONFIG_USBDEBUG_DIRECT=1
#HT Unit ID offset, default is 1, the typical one, 0 mean only one HT device
-default HT_CHAIN_UNITID_BASE=0
+default CONFIG_HT_CHAIN_UNITID_BASE=0
#real SB Unit ID, default is 0x20, mean dont touch it at last
-#default HT_CHAIN_END_UNITID_BASE=0x6
+#default CONFIG_HT_CHAIN_END_UNITID_BASE=0x6
#make the SB HT chain on bus 0, default is not (0)
-default SB_HT_CHAIN_ON_BUS0=2
+default CONFIG_SB_HT_CHAIN_ON_BUS0=2
#only offset for SB chain?, default is yes(1)
-default SB_HT_CHAIN_UNITID_OFFSET_ONLY=0
+default CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY=0
#allow capable device use that above 4G
#default CONFIG_PCI_64BIT_PREF_MEM=1
##
## enable CACHE_AS_RAM specifics
##
-default USE_DCACHE_RAM=1
-default DCACHE_RAM_BASE=0xc8000
-default DCACHE_RAM_SIZE=0x08000
-default DCACHE_RAM_GLOBAL_VAR_SIZE=0x01000
+default CONFIG_USE_DCACHE_RAM=1
+default CONFIG_DCACHE_RAM_BASE=0xc8000
+default CONFIG_DCACHE_RAM_SIZE=0x08000
+default CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE=0x01000
default CONFIG_USE_INIT=0
default CONFIG_AP_CODE_IN_CAR=0
-default MEM_TRAIN_SEQ=1
-default WAIT_BEFORE_CPUS_INIT=1
+default CONFIG_MEM_TRAIN_SEQ=1
+default CONFIG_WAIT_BEFORE_CPUS_INIT=1
##
## Build code to setup a generic IOAPIC
##
## Clean up the motherboard id strings
##
-default MAINBOARD_PART_NUMBER="S2912"
-default MAINBOARD_VENDOR="Tyan"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x10f1
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2912
+default CONFIG_MAINBOARD_PART_NUMBER="S2912"
+default CONFIG_MAINBOARD_VENDOR="Tyan"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x10f1
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2912
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 32K heap
##
-default HEAP_SIZE=0x8000
+default CONFIG_HEAP_SIZE=0x8000
##
## Only use the option table in a normal image
##
-default USE_OPTION_TABLE = (!USE_FALLBACK_IMAGE) && (!USE_FAILOVER_IMAGE )
+default CONFIG_USE_OPTION_TABLE = (!CONFIG_USE_FALLBACK_IMAGE) && (!CONFIG_USE_FAILOVER_IMAGE )
##
## Coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00100000
+default CONFIG_RAMBASE=0x00100000
##
## Load the payload from the ROM
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## Disable the gdb stub by default
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
### End Options.lb
#
void hardwaremain(int ret_addr)
{
- struct sys_info *sysinfo = (DCACHE_RAM_BASE + DCACHE_RAM_SIZE - DCACHE_RAM_GLOBAL_VAR_SIZE); // in CACHE
- struct sys_info *sysinfox = ((CONFIG_LB_MEM_TOPK<<10) - DCACHE_RAM_GLOBAL_VAR_SIZE); // in RAM
+ struct sys_info *sysinfo = (CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE); // in CACHE
+ struct sys_info *sysinfox = ((CONFIG_LB_MEM_TOPK<<10) - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE); // in RAM
struct node_core_id id;
//if we want to wait for core1 done before DQS training, set it to 0
#define K8_SET_FIDVID_CORE0_ONLY 1
-#if K8_REV_F_SUPPORT == 1
+#if CONFIG_K8_REV_F_SUPPORT == 1
#define K8_REV_F_SUPPORT_F0_F1_WORKAROUND 0
#endif
#include "option_table.h"
#include "pc80/mc146818rtc_early.c"
-#if USE_FAILOVER_IMAGE==0
+#if CONFIG_USE_FAILOVER_IMAGE==0
#include "pc80/serial.c"
#include "arch/i386/lib/console.c"
#if CONFIG_USBDEBUG_DIRECT
#include "superio/winbond/w83627hf/w83627hf_early_serial.c"
#include "superio/winbond/w83627hf/w83627hf_early_init.c"
-#if USE_FAILOVER_IMAGE==0
+#if CONFIG_USE_FAILOVER_IMAGE==0
#include "cpu/x86/bist.h"
#endif
-#if ((HAVE_FAILOVER_BOOT==1) && (USE_FAILOVER_IMAGE == 1)) || ((HAVE_FAILOVER_BOOT==0) && (USE_FALLBACK_IMAGE == 1))
+#if ((CONFIG_HAVE_FAILOVER_BOOT==1) && (CONFIG_USE_FAILOVER_IMAGE == 1)) || ((CONFIG_HAVE_FAILOVER_BOOT==0) && (CONFIG_USE_FALLBACK_IMAGE == 1))
#include "southbridge/nvidia/mcp55/mcp55_enable_rom.c"
#include "northbridge/amd/amdk8/early_ht.c"
);
fallback_image:
-#if HAVE_FAILOVER_BOOT==1
+#if CONFIG_HAVE_FAILOVER_BOOT==1
__asm__ volatile ("jmp __fallback_image"
: /* outputs */
: "a" (bist), "b" (cpu_init_detectedx) /* inputs */
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
-#if HAVE_FAILOVER_BOOT==1
- #if USE_FAILOVER_IMAGE==1
+#if CONFIG_HAVE_FAILOVER_BOOT==1
+ #if CONFIG_USE_FAILOVER_IMAGE==1
failover_process(bist, cpu_init_detectedx);
#else
real_main(bist, cpu_init_detectedx);
#endif
#else
- #if USE_FALLBACK_IMAGE == 1
+ #if CONFIG_USE_FALLBACK_IMAGE == 1
failover_process(bist, cpu_init_detectedx);
#endif
real_main(bist, cpu_init_detectedx);
#endif
}
-#if USE_FAILOVER_IMAGE==0
+#if CONFIG_USE_FAILOVER_IMAGE==0
void real_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
#endif
};
- struct sys_info *sysinfo = (DCACHE_RAM_BASE + DCACHE_RAM_SIZE - DCACHE_RAM_GLOBAL_VAR_SIZE);
+ struct sys_info *sysinfo = (CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE);
int needs_reset = 0;
unsigned bsp_apicid = 0;
bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);
}
- w83627hf_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ w83627hf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
setup_mb_resource_map();
print_debug("bsp_apicid="); print_debug_hex8(bsp_apicid); print_debug("\r\n");
-#if MEM_TRAIN_SEQ == 1
+#if CONFIG_MEM_TRAIN_SEQ == 1
set_sysinfo_in_ram(0); // in BSP so could hold all ap until sysinfo is in ram
#endif
setup_coherent_ht_domain(); // routing table and start other core0
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/failovercalculation.lb
arch i386 end
#needed by irq_tables and mptable and acpi_tables
object get_bus_conf.o
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
#object reset.o
if CONFIG_USE_INIT
makerule ./cache_as_ram_auto.o
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
end
else
makerule ./cache_as_ram_auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
end
-if USE_FAILOVER_IMAGE
+if CONFIG_USE_FAILOVER_IMAGE
else
if CONFIG_AP_CODE_IN_CAR
makerule ./apc_auto.o
- depends "$(MAINBOARD)/apc_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/apc_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/apc_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/apc_auto.c -o $@"
end
ldscript /arch/i386/init/ldscript_apc.lb
end
##
## Build our 16 bit and 32 bit coreboot entry code
##
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
end
##
## Build our reset vector (This is where coreboot is entered)
##
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
ldscript /cpu/x86/32bit/reset32.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
##
## ROMSTRAP table for MCP55
##
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
mainboardinit southbridge/nvidia/mcp55/romstrap.inc
ldscript /southbridge/nvidia/mcp55/romstrap.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
mainboardinit southbridge/nvidia/mcp55/romstrap.inc
ldscript /southbridge/nvidia/mcp55/romstrap.lds
end
### Things are delicate and we test to see if we should
### failover to another image.
###
-if HAVE_FAILOVER_BOOT
- if USE_FAILOVER_IMAGE
+if CONFIG_HAVE_FAILOVER_BOOT
+ if CONFIG_USE_FAILOVER_IMAGE
ldscript /arch/i386/lib/failover_failover.lds
end
else
- if USE_FALLBACK_IMAGE
+ if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
end
end
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses HAVE_ACPI_TABLES
-uses HAVE_ACPI_RESUME
-uses ACPI_SSDTX_NUM
-uses USE_FALLBACK_IMAGE
-uses USE_FAILOVER_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_FAILOVER_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_HAVE_ACPI_TABLES
+uses CONFIG_HAVE_ACPI_RESUME
+uses CONFIG_ACPI_SSDTX_NUM
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_USE_FAILOVER_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_FAILOVER_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_MAX_CPUS
uses CONFIG_MAX_PHYSICAL_CPUS
uses CONFIG_LOGICAL_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses FAILOVER_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_FAILOVER_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_NRV2B
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
-uses _RAMBASE
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_RAMBASE
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_SERIAL8250
-uses HAVE_INIT_TIMER
+uses CONFIG_HAVE_INIT_TIMER
uses CONFIG_GDB_STUB
uses CONFIG_GDB_STUB
-uses CROSS_COMPILE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
uses CONFIG_CONSOLE_VGA
uses CONFIG_USBDEBUG_DIRECT
uses CONFIG_PCI_ROM_RUN
-uses HW_MEM_HOLE_SIZEK
-uses HW_MEM_HOLE_SIZE_AUTO_INC
-
-uses HT_CHAIN_UNITID_BASE
-uses HT_CHAIN_END_UNITID_BASE
-uses SB_HT_CHAIN_ON_BUS0
-uses SB_HT_CHAIN_UNITID_OFFSET_ONLY
-
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
-uses DCACHE_RAM_GLOBAL_VAR_SIZE
+uses CONFIG_HW_MEM_HOLE_SIZEK
+uses CONFIG_HW_MEM_HOLE_SIZE_AUTO_INC
+
+uses CONFIG_HT_CHAIN_UNITID_BASE
+uses CONFIG_HT_CHAIN_END_UNITID_BASE
+uses CONFIG_SB_HT_CHAIN_ON_BUS0
+uses CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY
+
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
+uses CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE
uses CONFIG_USE_INIT
-uses SERIAL_CPU_INIT
+uses CONFIG_SERIAL_CPU_INIT
-uses ENABLE_APIC_EXT_ID
-uses APIC_ID_OFFSET
-uses LIFT_BSP_APIC_ID
+uses CONFIG_ENABLE_APIC_EXT_ID
+uses CONFIG_APIC_ID_OFFSET
+uses CONFIG_LIFT_BSP_APIC_ID
uses CONFIG_PCI_64BIT_PREF_MEM
uses CONFIG_LB_MEM_TOPK
-uses PCI_BUS_SEGN_BITS
+uses CONFIG_PCI_BUS_SEGN_BITS
uses CONFIG_AP_CODE_IN_CAR
-uses MEM_TRAIN_SEQ
+uses CONFIG_MEM_TRAIN_SEQ
-uses WAIT_BEFORE_CPUS_INIT
+uses CONFIG_WAIT_BEFORE_CPUS_INIT
uses CONFIG_AMDMCT
uses CONFIG_USE_PRINTK_IN_CAR
-uses CAR_FAM10
-uses AMD_UCODE_PATCH_FILE
+uses CONFIG_CAR_FAM10
+uses CONFIG_AMD_UCODE_PATCH_FILE
###
### Build options
###
##
-## ROM_SIZE is the size of boot ROM that this board will use.
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
##
-default ROM_SIZE=1024*1024
-#default ROM_SIZE=0x100000
+default CONFIG_ROM_SIZE=1024*1024
+#default CONFIG_ROM_SIZE=0x100000
##
-## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
+## CONFIG_FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
##
-#default FALLBACK_SIZE=131072
-#default FALLBACK_SIZE=0x40000
+#default CONFIG_FALLBACK_SIZE=131072
+#default CONFIG_FALLBACK_SIZE=0x40000
-default FALLBACK_SIZE=0x3f000
-default FAILOVER_SIZE=0x01000
+default CONFIG_FALLBACK_SIZE=0x3f000
+default CONFIG_FAILOVER_SIZE=0x01000
#more 1M for pgtbl
default CONFIG_LB_MEM_TOPK=16384
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
-default HAVE_FAILOVER_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FAILOVER_BOOT=1
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=11
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=11
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
## ACPI tables will be included
-default HAVE_ACPI_TABLES=0
+default CONFIG_HAVE_ACPI_TABLES=0
## extra SSDT num
-default ACPI_SSDTX_NUM=31
+default CONFIG_ACPI_SSDTX_NUM=31
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
##
## Move the default coreboot cmos range off of AMD RTC registers
##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
+default CONFIG_LB_CKS_RANGE_START=49
+default CONFIG_LB_CKS_RANGE_END=122
+default CONFIG_LB_CKS_LOC=123
##
## Build code for SMP support
default CONFIG_MAX_CPUS=4 * CONFIG_MAX_PHYSICAL_CPUS
default CONFIG_LOGICAL_CPUS=1
-#default SERIAL_CPU_INIT=0
+#default CONFIG_SERIAL_CPU_INIT=0
-default ENABLE_APIC_EXT_ID=1
-default APIC_ID_OFFSET=0x00
-default LIFT_BSP_APIC_ID=1
+default CONFIG_ENABLE_APIC_EXT_ID=1
+default CONFIG_APIC_ID_OFFSET=0x00
+default CONFIG_LIFT_BSP_APIC_ID=1
#memory hole size, 0 mean disable, others will enable the hole, at that case if it is small than mmio_basek, it will use mmio_basek instead.
#2G
-#default HW_MEM_HOLE_SIZEK=0x200000
+#default CONFIG_HW_MEM_HOLE_SIZEK=0x200000
#1G
-default HW_MEM_HOLE_SIZEK=0x100000
+default CONFIG_HW_MEM_HOLE_SIZEK=0x100000
#512M
-#default HW_MEM_HOLE_SIZEK=0x80000
+#default CONFIG_HW_MEM_HOLE_SIZEK=0x80000
#make auto increase hole size to avoid hole_startk equal to basek so as to make some kernel happy
-#default HW_MEM_HOLE_SIZE_AUTO_INC=1
+#default CONFIG_HW_MEM_HOLE_SIZE_AUTO_INC=1
#VGA Console
default CONFIG_CONSOLE_VGA=1
#default CONFIG_USBDEBUG_DIRECT=1
#HT Unit ID offset, default is 1, the typical one, 0 mean only one HT device
-default HT_CHAIN_UNITID_BASE=1
+default CONFIG_HT_CHAIN_UNITID_BASE=1
#real SB Unit ID, default is 0x20, mean dont touch it at last
-#default HT_CHAIN_END_UNITID_BASE=0x6
+#default CONFIG_HT_CHAIN_END_UNITID_BASE=0x6
#make the SB HT chain on bus 0, default is not (0)
-default SB_HT_CHAIN_ON_BUS0=2
+default CONFIG_SB_HT_CHAIN_ON_BUS0=2
#only offset for SB chain?, default is yes(1)
-default SB_HT_CHAIN_UNITID_OFFSET_ONLY=0
+default CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY=0
#allow capable device use that above 4G
#default CONFIG_PCI_64BIT_PREF_MEM=1
##
## enable CACHE_AS_RAM specifics
##
-default USE_DCACHE_RAM=1
-default DCACHE_RAM_BASE=0xc4000
-default DCACHE_RAM_SIZE=0x0c000
-default DCACHE_RAM_GLOBAL_VAR_SIZE=0x04000
+default CONFIG_USE_DCACHE_RAM=1
+default CONFIG_DCACHE_RAM_BASE=0xc4000
+default CONFIG_DCACHE_RAM_SIZE=0x0c000
+default CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE=0x04000
default CONFIG_USE_INIT=0
-default MEM_TRAIN_SEQ=2
-default WAIT_BEFORE_CPUS_INIT=0
+default CONFIG_MEM_TRAIN_SEQ=2
+default CONFIG_WAIT_BEFORE_CPUS_INIT=0
default CONFIG_AMDMCT = 1
##
##
## Clean up the motherboard id strings
##
-default MAINBOARD_PART_NUMBER="S2912 (Fam10)"
-default MAINBOARD_VENDOR="Tyan"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x10f1
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2912
+default CONFIG_MAINBOARD_PART_NUMBER="S2912 (Fam10)"
+default CONFIG_MAINBOARD_VENDOR="Tyan"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x10f1
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2912
##
## Set microcode patch file name
## Barcelona rev DR-B2, B3: "mc_patch_01000095.h"
## Shanghai rev DA-C2: "mc_patch_0100009f.h"
##
-default AMD_UCODE_PATCH_FILE="mc_patch_01000095.h"
+default CONFIG_AMD_UCODE_PATCH_FILE="mc_patch_01000095.h"
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 32K heap
##
-default HEAP_SIZE=0xc0000
+default CONFIG_HEAP_SIZE=0xc0000
##
## Only use the option table in a normal image
##
-default USE_OPTION_TABLE = (!USE_FALLBACK_IMAGE) && (!USE_FAILOVER_IMAGE )
+default CONFIG_USE_OPTION_TABLE = (!CONFIG_USE_FALLBACK_IMAGE) && (!CONFIG_USE_FAILOVER_IMAGE )
##
## Coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00200000
+default CONFIG_RAMBASE=0x00200000
##
## Load the payload from the ROM
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## Disable the gdb stub by default
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
### End Options.lb
#
void hardwaremain(int ret_addr)
{
- struct sys_info *sysinfo = (DCACHE_RAM_BASE + DCACHE_RAM_SIZE - DCACHE_RAM_GLOBAL_VAR_SIZE); // in CACHE
- struct sys_info *sysinfox = ((CONFIG_LB_MEM_TOPK<<10) - DCACHE_RAM_GLOBAL_VAR_SIZE); // in RAM
+ struct sys_info *sysinfo = (CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE); // in CACHE
+ struct sys_info *sysinfox = ((CONFIG_LB_MEM_TOPK<<10) - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE); // in RAM
struct node_core_id id;
outb(value, 0x80);
}
-#if USE_FAILOVER_IMAGE==0
+#if CONFIG_USE_FAILOVER_IMAGE==0
#include "pc80/serial.c"
#include "arch/i386/lib/console.c"
#if CONFIG_USBDEBUG_DIRECT
#include "superio/winbond/w83627hf/w83627hf_early_serial.c"
#include "superio/winbond/w83627hf/w83627hf_early_init.c"
-#if USE_FAILOVER_IMAGE==0
+#if CONFIG_USE_FAILOVER_IMAGE==0
#include "cpu/x86/bist.h"
#endif
-#if ((HAVE_FAILOVER_BOOT==1) && (USE_FAILOVER_IMAGE == 1)) || ((HAVE_FAILOVER_BOOT==0) && (USE_FALLBACK_IMAGE == 1))
+#if ((CONFIG_HAVE_FAILOVER_BOOT==1) && (CONFIG_USE_FAILOVER_IMAGE == 1)) || ((CONFIG_HAVE_FAILOVER_BOOT==0) && (CONFIG_USE_FALLBACK_IMAGE == 1))
#include "southbridge/nvidia/mcp55/mcp55_enable_rom.c"
#include "northbridge/amd/amdfam10/early_ht.c"
);
fallback_image:
-#if HAVE_FAILOVER_BOOT==1
+#if CONFIG_HAVE_FAILOVER_BOOT==1
__asm__ volatile ("jmp __fallback_image"
: /* outputs */
: "a" (bist), "b" (cpu_init_detectedx) /* inputs */
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
-#if HAVE_FAILOVER_BOOT==1
- #if USE_FAILOVER_IMAGE==1
+#if CONFIG_HAVE_FAILOVER_BOOT==1
+ #if CONFIG_USE_FAILOVER_IMAGE==1
failover_process(bist, cpu_init_detectedx);
#else
real_main(bist, cpu_init_detectedx);
#endif
#else
- #if USE_FALLBACK_IMAGE == 1
+ #if CONFIG_USE_FALLBACK_IMAGE == 1
failover_process(bist, cpu_init_detectedx);
#endif
real_main(bist, cpu_init_detectedx);
#endif
}
-#if USE_FAILOVER_IMAGE==0
+#if CONFIG_USE_FAILOVER_IMAGE==0
#include "spd_addr.h"
#include "cpu/amd/microcode/microcode.c"
#include "cpu/amd/model_10xxx/update_microcode.c"
void real_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
- struct sys_info *sysinfo = (struct sys_info *)(DCACHE_RAM_BASE + DCACHE_RAM_SIZE - DCACHE_RAM_GLOBAL_VAR_SIZE);
+ struct sys_info *sysinfo = (struct sys_info *)(CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE);
u32 bsp_apicid = 0;
u32 val;
post_code(0x32);
- w83627hf_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ w83627hf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
printk_debug("\n");
pirq_info++; slot_num++;
}
-#if CBB
- write_pirq_info(pirq_info, CBB, (0<<3)|0, 0x1, 0xdef8, 0x2, 0xdef8, 0x3, 0xdef8, 0x4, 0xdef8, 0, 0);
+#if CONFIG_CBB
+ write_pirq_info(pirq_info, CONFIG_CBB, (0<<3)|0, 0x1, 0xdef8, 0x2, 0xdef8, 0x3, 0xdef8, 0x4, 0xdef8, 0, 0);
pirq_info++; slot_num++;
if(sysconf.nodes>32) {
- write_pirq_info(pirq_info, CBB-1, (0<<3)|0, 0x1, 0xdef8, 0x2, 0xdef8, 0x3, 0xdef8, 0x4, 0xdef8, 0, 0);
+ write_pirq_info(pirq_info, CONFIG_CBB-1, (0<<3)|0, 0x1, 0xdef8, 0x2, 0xdef8, 0x3, 0xdef8, 0x4, 0xdef8, 0, 0);
pirq_info++; slot_num++;
}
#endif
* This field defines the upper address bits of a 40 bit address
* that define the end of the DRAM region.
*/
- // PCI_ADDR(CBB, CDB, 1, 0x44), 0x0000f8f8, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0x4C), 0x0000f8f8, 0x00000001,
- PCI_ADDR(CBB, CDB, 1, 0x54), 0x0000f8f8, 0x00000002,
- PCI_ADDR(CBB, CDB, 1, 0x5C), 0x0000f8f8, 0x00000003,
- PCI_ADDR(CBB, CDB, 1, 0x64), 0x0000f8f8, 0x00000004,
- PCI_ADDR(CBB, CDB, 1, 0x6C), 0x0000f8f8, 0x00000005,
- PCI_ADDR(CBB, CDB, 1, 0x74), 0x0000f8f8, 0x00000006,
- PCI_ADDR(CBB, CDB, 1, 0x7C), 0x0000f8f8, 0x00000007,
+ // PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x44), 0x0000f8f8, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x4C), 0x0000f8f8, 0x00000001,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x54), 0x0000f8f8, 0x00000002,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x5C), 0x0000f8f8, 0x00000003,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x64), 0x0000f8f8, 0x00000004,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x6C), 0x0000f8f8, 0x00000005,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x74), 0x0000f8f8, 0x00000006,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x7C), 0x0000f8f8, 0x00000007,
/* DRAM Base i Registers
* F1:0x40 i = 0
* This field defines the upper address bits of a 40-bit address
* that define the start of the DRAM region.
*/
- // PCI_ADDR(CBB, CDB, 1, 0x40), 0x0000f8fc, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0x48), 0x0000f8fc, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0x50), 0x0000f8fc, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0x58), 0x0000f8fc, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0x60), 0x0000f8fc, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0x68), 0x0000f8fc, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0x70), 0x0000f8fc, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0x78), 0x0000f8fc, 0x00000000,
+ // PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x40), 0x0000f8fc, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x48), 0x0000f8fc, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x50), 0x0000f8fc, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x58), 0x0000f8fc, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x60), 0x0000f8fc, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x68), 0x0000f8fc, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x70), 0x0000f8fc, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x78), 0x0000f8fc, 0x00000000,
/* Memory-Mapped I/O Limit i Registers
* F1:0x84 i = 0
* This field defines the upp adddress bits of a 40-bit address that
* defines the end of a memory-mapped I/O region n
*/
- PCI_ADDR(CBB, CDB, 1, 0x84), 0x00000048, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0x8C), 0x00000048, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0x94), 0x00000048, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0x9C), 0x00000048, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0xA4), 0x00000048, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0xAC), 0x00000048, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0xB4), 0x00000048, 0x00000000,
-// PCI_ADDR(CBB, CDB, 1, 0xBC), 0x00000048, 0x00ffff00,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x84), 0x00000048, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x8C), 0x00000048, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x94), 0x00000048, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x9C), 0x00000048, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xA4), 0x00000048, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xAC), 0x00000048, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xB4), 0x00000048, 0x00000000,
+// PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xBC), 0x00000048, 0x00ffff00,
/* Memory-Mapped I/O Base i Registers
* F1:0x80 i = 0
* This field defines the upper address bits of a 40bit address
* that defines the start of memory-mapped I/O region i
*/
- PCI_ADDR(CBB, CDB, 1, 0x80), 0x000000f0, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0x88), 0x000000f0, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0x90), 0x000000f0, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0x98), 0x000000f0, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0xA0), 0x000000f0, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0xA8), 0x000000f0, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0xB0), 0x000000f0, 0x00000000,
-// PCI_ADDR(CBB, CDB, 1, 0xB8), 0x000000f0, 0x00fc0003,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x80), 0x000000f0, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x88), 0x000000f0, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x90), 0x000000f0, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x98), 0x000000f0, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xA0), 0x000000f0, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xA8), 0x000000f0, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xB0), 0x000000f0, 0x00000000,
+// PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xB8), 0x000000f0, 0x00fc0003,
/* PCI I/O Limit i Registers
* F1:0xC4 i = 0
* This field defines the end of PCI I/O region n
* [31:25] Reserved
*/
-// PCI_ADDR(CBB, CDB, 1, 0xC4), 0xFE000FC8, 0x00007000,
-// PCI_ADDR(CBB, CDB, 1, 0xCC), 0xFE000FC8, 0x01fff020, // need to talk to ANALOG of second CK804 to release PCI E reset
- PCI_ADDR(CBB, CDB, 1, 0xD4), 0xFE000FC8, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0xDC), 0xFE000FC8, 0x00000000,
+// PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xC4), 0xFE000FC8, 0x00007000,
+// PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xCC), 0xFE000FC8, 0x01fff020, // need to talk to ANALOG of second CK804 to release PCI E reset
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xD4), 0xFE000FC8, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xDC), 0xFE000FC8, 0x00000000,
/* PCI I/O Base i Registers
* F1:0xC0 i = 0
* This field defines the start of PCI I/O region n
* [31:25] Reserved
*/
-// PCI_ADDR(CBB, CDB, 1, 0xC0), 0xFE000FCC, 0x00000033,
-// PCI_ADDR(CBB, CDB, 1, 0xC8), 0xFE000FCC, 0x00008033,
- PCI_ADDR(CBB, CDB, 1, 0xD0), 0xFE000FCC, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0xD8), 0xFE000FCC, 0x00000000,
+// PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xC0), 0xFE000FCC, 0x00000033,
+// PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xC8), 0xFE000FCC, 0x00008033,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xD0), 0xFE000FCC, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xD8), 0xFE000FCC, 0x00000000,
/* Config Base and Limit i Registers
* F1:0xE0 i = 0
* [31:24] Bus Number Limit i
* This field defines the highest bus number in configuration region i
*/
-// PCI_ADDR(CBB, CDB, 1, 0xE0), 0x0000FC88, 0x3f000003, /* link 0 of cpu 0 --> Nvidia MCP55 Pro */
-// PCI_ADDR(CBB, CDB, 1, 0xE4), 0x0000FC88, 0x7f400203, /* link 2 of cpu 0 --> nvidia io55 */
- PCI_ADDR(CBB, CDB, 1, 0xE8), 0x0000FC88, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0xEC), 0x0000FC88, 0x00000000,
+// PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xE0), 0x0000FC88, 0x3f000003, /* link 0 of cpu 0 --> Nvidia MCP55 Pro */
+// PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xE4), 0x0000FC88, 0x7f400203, /* link 2 of cpu 0 --> nvidia io55 */
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xE8), 0x0000FC88, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xEC), 0x0000FC88, 0x00000000,
};
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
default CONFIG_ROM_PAYLOAD = 1
##
driver mainboard.o
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
if CONFIG_USE_INIT
makerule ./auto.o
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
end
else
makerule ./auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
##
## Build our 16 bit and 32 bit coreboot entry code
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
end
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
end
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_MAX_CPUS
uses CONFIG_MAX_PHYSICAL_CPUS
uses CONFIG_LOGICAL_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
-uses _RAMBASE
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_RAMBASE
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_SERIAL8250
-uses HAVE_INIT_TIMER
+uses CONFIG_HAVE_INIT_TIMER
uses CONFIG_GDB_STUB
uses CONFIG_GDB_STUB
-uses CROSS_COMPILE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
-uses HW_MEM_HOLE_SIZEK
+uses CONFIG_HW_MEM_HOLE_SIZEK
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
uses CONFIG_USE_INIT
uses CONFIG_USE_PRINTK_IN_CAR
-uses ENABLE_APIC_EXT_ID
-uses APIC_ID_OFFSET
-uses LIFT_BSP_APIC_ID
+uses CONFIG_ENABLE_APIC_EXT_ID
+uses CONFIG_APIC_ID_OFFSET
+uses CONFIG_LIFT_BSP_APIC_ID
###
### Build options
###
##
-## ROM_SIZE is the size of boot ROM that this board will use.
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
##
-default ROM_SIZE=524288
+default CONFIG_ROM_SIZE=524288
##
-## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
+## CONFIG_FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
##
-#default FALLBACK_SIZE=131072
+#default CONFIG_FALLBACK_SIZE=131072
#256K
-default FALLBACK_SIZE=0x40000
+default CONFIG_FALLBACK_SIZE=0x40000
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=22
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=22
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
##
## Move the default coreboot cmos range off of AMD RTC registers
##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
+default CONFIG_LB_CKS_RANGE_START=49
+default CONFIG_LB_CKS_RANGE_END=122
+default CONFIG_LB_CKS_LOC=123
##
## Build code for SMP support
default CONFIG_LOGICAL_CPUS=1
#1G memory hole
-default HW_MEM_HOLE_SIZEK=0x100000
+default CONFIG_HW_MEM_HOLE_SIZEK=0x100000
#VGA Console
default CONFIG_CONSOLE_VGA=1
##
## enable CACHE_AS_RAM specifics
##
-default USE_DCACHE_RAM=1
-default DCACHE_RAM_BASE=0xcf000
-default DCACHE_RAM_SIZE=0x1000
+default CONFIG_USE_DCACHE_RAM=1
+default CONFIG_DCACHE_RAM_BASE=0xcf000
+default CONFIG_DCACHE_RAM_SIZE=0x1000
default CONFIG_USE_INIT=0
-default ENABLE_APIC_EXT_ID=1
-default APIC_ID_OFFSET=0x10
-default LIFT_BSP_APIC_ID=0
+default CONFIG_ENABLE_APIC_EXT_ID=1
+default CONFIG_APIC_ID_OFFSET=0x10
+default CONFIG_LIFT_BSP_APIC_ID=0
##
##
## Clean up the motherboard id strings
##
-default MAINBOARD_VENDOR="Tyan"
-default MAINBOARD_PART_NUMBER="s4880"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x10f1
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x4880
+default CONFIG_MAINBOARD_VENDOR="Tyan"
+default CONFIG_MAINBOARD_PART_NUMBER="s4880"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x10f1
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x4880
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE=0x4000
+default CONFIG_HEAP_SIZE=0x4000
##
## Only use the option table in a normal image
##
-default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
##
## Coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00004000
+default CONFIG_RAMBASE=0x00004000
##
## Load the payload from the ROM
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## Disable the gdb stub by default
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
### End Options.lb
#
#include "cpu/amd/model_fxx/init_cpus.c"
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
#include "southbridge/amd/amd8111/amd8111_enable_rom.c"
#include "northbridge/amd/amdk8/early_ht.c"
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
failover_process(bist, cpu_init_detectedx);
#endif
real_main(bist, cpu_init_detectedx);
init_cpus(cpu_init_detectedx);
}
- w83627hf_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ w83627hf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
default CONFIG_ROM_PAYLOAD = 1
##
driver mainboard.o
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
if CONFIG_USE_INIT
makerule ./auto.o
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
end
else
makerule ./auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/cache_as_ram_auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
##
## Build our 16 bit and 32 bit coreboot entry code
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/entry16.inc
ldscript /cpu/x86/16bit/entry16.lds
end
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
end
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_MAX_CPUS
uses CONFIG_MAX_PHYSICAL_CPUS
uses CONFIG_LOGICAL_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
-uses _RAMBASE
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_RAMBASE
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_SERIAL8250
-uses HAVE_INIT_TIMER
+uses CONFIG_HAVE_INIT_TIMER
uses CONFIG_GDB_STUB
uses CONFIG_GDB_STUB
-uses CROSS_COMPILE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
-uses HW_MEM_HOLE_SIZEK
+uses CONFIG_HW_MEM_HOLE_SIZEK
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
uses CONFIG_USE_INIT
uses CONFIG_USE_PRINTK_IN_CAR
-uses ENABLE_APIC_EXT_ID
-uses APIC_ID_OFFSET
-uses LIFT_BSP_APIC_ID
+uses CONFIG_ENABLE_APIC_EXT_ID
+uses CONFIG_APIC_ID_OFFSET
+uses CONFIG_LIFT_BSP_APIC_ID
###
### Build options
###
##
-## ROM_SIZE is the size of boot ROM that this board will use.
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
##
-default ROM_SIZE=524288
+default CONFIG_ROM_SIZE=524288
##
-## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
+## CONFIG_FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
##
-#default FALLBACK_SIZE=131072
+#default CONFIG_FALLBACK_SIZE=131072
#256K
-default FALLBACK_SIZE=0x40000
+default CONFIG_FALLBACK_SIZE=0x40000
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=22
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=22
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
##
## Move the default coreboot cmos range off of AMD RTC registers
##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
+default CONFIG_LB_CKS_RANGE_START=49
+default CONFIG_LB_CKS_RANGE_END=122
+default CONFIG_LB_CKS_LOC=123
##
## Build code for SMP support
default CONFIG_LOGICAL_CPUS=1
#1G memory hole
-default HW_MEM_HOLE_SIZEK=0x100000
+default CONFIG_HW_MEM_HOLE_SIZEK=0x100000
#VGA Console
#default CONFIG_CONSOLE_VGA=1
##
## enable CACHE_AS_RAM specifics
##
-default USE_DCACHE_RAM=1
-default DCACHE_RAM_BASE=0xcf000
-default DCACHE_RAM_SIZE=0x1000
+default CONFIG_USE_DCACHE_RAM=1
+default CONFIG_DCACHE_RAM_BASE=0xcf000
+default CONFIG_DCACHE_RAM_SIZE=0x1000
default CONFIG_USE_INIT=0
-default ENABLE_APIC_EXT_ID=1
-default APIC_ID_OFFSET=0x10
-default LIFT_BSP_APIC_ID=0
+default CONFIG_ENABLE_APIC_EXT_ID=1
+default CONFIG_APIC_ID_OFFSET=0x10
+default CONFIG_LIFT_BSP_APIC_ID=0
##
## Build code to setup a generic IOAPIC
##
## Clean up the motherboard id strings
##
-default MAINBOARD_VENDOR="Tyan"
-default MAINBOARD_PART_NUMBER="s4882"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x10f1
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x4882
+default CONFIG_MAINBOARD_VENDOR="Tyan"
+default CONFIG_MAINBOARD_PART_NUMBER="s4882"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x10f1
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x4882
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE=0x4000
+default CONFIG_HEAP_SIZE=0x4000
##
## Only use the option table in a normal image
##
-default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
##
## Coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00002000
+default CONFIG_RAMBASE=0x00002000
##
## Load the payload from the ROM
##
## The default compiler
##
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## Disable the gdb stub by default
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
### End Options.lb
#
#include "cpu/amd/model_fxx/init_cpus.c"
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
#include "southbridge/amd/amd8111/amd8111_enable_rom.c"
#include "northbridge/amd/amdk8/early_ht.c"
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
failover_process(bist, cpu_init_detectedx);
#endif
real_main(bist, cpu_init_detectedx);
}
- w83627hf_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ w83627hf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
arch i386 end
driver mainboard.o
-if HAVE_PIRQ_TABLE object irq_tables.o end
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_ACPI_TABLES
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_ACPI_TABLES
object fadt.o
object dsdt.o
object acpi_tables.o
end
makerule ./failover.E
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./auto.E
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -E -mcpu=c3 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -E -mcpu=c3 -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -mcpu=c3 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -mcpu=c3 -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
mainboardinit cpu/x86/16bit/entry16.inc
mainboardinit cpu/x86/32bit/entry32.inc
ldscript /cpu/x86/16bit/entry16.lds
ldscript /cpu/x86/32bit/entry32.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
mainboardinit arch/i386/lib/cpu_reset.inc
mainboardinit arch/i386/lib/id.inc
ldscript /arch/i386/lib/id.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_ROM_PAYLOAD
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_NRV2B
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses HAVE_MP_TABLE
-uses HAVE_ACPI_TABLES
-uses HAVE_ACPI_RESUME
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_HAVE_ACPI_TABLES
+uses CONFIG_HAVE_ACPI_RESUME
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
uses CONFIG_PCI_ROM_RUN
uses CONFIG_CONSOLE_VGA
uses CONFIG_MAX_PCI_BUSES
-uses TTYS0_BAUD
+uses CONFIG_TTYS0_BAUD
uses CONFIG_VIDEO_MB
uses CONFIG_IOAPIC
-default ROM_SIZE = 512 * 1024
+default CONFIG_ROM_SIZE = 512 * 1024
default CONFIG_IOAPIC = 0
default CONFIG_VIDEO_MB = 32
default CONFIG_CONSOLE_SERIAL8250 = 1
default CONFIG_PCI_ROM_RUN = 0
default CONFIG_CONSOLE_VGA = 0
-default HAVE_FALLBACK_BOOT = 1
-default HAVE_MP_TABLE = 0
+default CONFIG_HAVE_FALLBACK_BOOT = 1
+default CONFIG_HAVE_MP_TABLE = 0
default CONFIG_UDELAY_TSC = 1
default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 1
-default HAVE_HARD_RESET = 0
-default HAVE_PIRQ_TABLE = 1
-default IRQ_SLOT_COUNT = 9
-default HAVE_ACPI_TABLES = 0
-default HAVE_OPTION_TABLE = 1
-default ROM_IMAGE_SIZE = 64 * 1024
-default FALLBACK_SIZE = ROM_SIZE
-default USE_FALLBACK_IMAGE = 1
-default STACK_SIZE = 8 * 1024
-default HEAP_SIZE = 16 * 1024
-#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_HAVE_HARD_RESET = 0
+default CONFIG_HAVE_PIRQ_TABLE = 1
+default CONFIG_IRQ_SLOT_COUNT = 9
+default CONFIG_HAVE_ACPI_TABLES = 0
+default CONFIG_HAVE_OPTION_TABLE = 1
+default CONFIG_ROM_IMAGE_SIZE = 64 * 1024
+default CONFIG_FALLBACK_SIZE = CONFIG_ROM_SIZE
+default CONFIG_USE_FALLBACK_IMAGE = 1
+default CONFIG_STACK_SIZE = 8 * 1024
+default CONFIG_HEAP_SIZE = 16 * 1024
+#default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 0
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
-default CROSS_COMPILE = ""
-default CC = "$(CROSS_COMPILE)gcc -m32 -fno-stack-protector"
-default HOSTCC = "gcc"
+default CONFIG_CROSS_COMPILE = ""
+default CC = "$(CONFIG_CROSS_COMPILE)gcc -m32 -fno-stack-protector"
+default CONFIG_HOSTCC = "gcc"
##
## Set this to the max PCI bus number you would ever use for PCI config I/O.
const struct irq_routing_table intel_irq_routing_table = {
PIRQ_SIGNATURE,
PIRQ_VERSION,
- 32 + 16 * IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
+ 32 + 16 * CONFIG_IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
0x00, /* Interrupt router bus */
(0x11 << 3) | 0x0, /* Interrupt router device */
0xc20, /* IRQs devoted exclusively to PCI usage */
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
##
##
driver mainboard.o
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
#object reset.o
object vgabios.o
-if HAVE_ACPI_TABLES
+if CONFIG_HAVE_ACPI_TABLES
object fadt.o
object dsdt.o
object acpi_tables.o
## Romcc output
##
makerule ./failover.E
- depends "$(MAINBOARD)/failover.c ../romcc"
- action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/failover.c ../romcc"
+ action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/failover.c ../romcc"
- action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/failover.c ../romcc"
+ action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/failover.c -o $@"
end
makerule ./auto.E
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -E -mcpu=c3 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -E -mcpu=c3 -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -mcpu=c3 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -mcpu=c3 -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
##
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_ROM_PAYLOAD
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_NRV2B
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses HAVE_MP_TABLE
-uses HAVE_ACPI_TABLES
-uses HAVE_ACPI_RESUME
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_HAVE_ACPI_TABLES
+uses CONFIG_HAVE_ACPI_RESUME
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
uses CONFIG_PCI_ROM_RUN
uses CONFIG_CONSOLE_VGA
uses CONFIG_MAX_PCI_BUSES
-uses TTYS0_BAUD
+uses CONFIG_TTYS0_BAUD
-## ROM_SIZE is the size of boot ROM that this board will use.
-default ROM_SIZE = 256*1024
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
+default CONFIG_ROM_SIZE = 256*1024
###
### Build options
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## no MP table
##
-default HAVE_MP_TABLE=0
+default CONFIG_HAVE_MP_TABLE=0
##
## Use TSC for udelay.
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=0
+default CONFIG_HAVE_HARD_RESET=0
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=5
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=5
##
## Build code to load acpi tables
##
-default HAVE_ACPI_TABLES=1
+default CONFIG_HAVE_ACPI_TABLES=1
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
-default FALLBACK_SIZE = 131072
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
+default CONFIG_FALLBACK_SIZE = 131072
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE=0x4000
+default CONFIG_HEAP_SIZE=0x4000
##
## Only use the option table in a normal image
##
-#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
+#default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
##
## The default compiler
##
-default CROSS_COMPILE=""
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CONFIG_CROSS_COMPILE=""
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## Set this to the max PCI bus number you
##
default CONFIG_MAX_PCI_BUSES = 5
-default MAXIMUM_CONSOLE_LOGLEVEL=8
-default DEFAULT_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
default CONFIG_CONSOLE_SERIAL8250=1
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
arch i386 end
driver mainboard.o
driver wakeup.o
-if HAVE_PIRQ_TABLE object irq_tables.o end
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_ACPI_TABLES
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_ACPI_TABLES
object fadt.o
object dsdt.o
# object ssdt.o
end
# These lines maybe noused.
makerule ./failover.E
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ./romcc"
- action "./romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ./romcc"
+ action "./romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ./romcc"
- action "./romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ./romcc"
+ action "./romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
-if USE_DCACHE_RAM
+if CONFIG_USE_DCACHE_RAM
if CONFIG_USE_INIT
makerule ./cache_as_ram_auto.o
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/cache_as_ram_auto.c -Os -nostdinc -nostdlib -fno-builtin -Wall -c -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -Os -nostdinc -nostdlib -fno-builtin -Wall -c -o $@"
end
else
makerule ./cache_as_ram_auto.inc
- depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/cache_as_ram_auto.c -Os -nostdinc -nostdlib -fno-builtin -Wall -c -S -o $@"
+ depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -Os -nostdinc -nostdlib -fno-builtin -Wall -c -S -o $@"
action "perl -e 's/.rodata/.rom.data/g' -pi $@"
action "perl -e 's/.text/.section .rom.text/g' -pi $@"
end
mainboardinit cpu/x86/32bit/entry32.inc
ldscript /cpu/x86/32bit/entry32.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
mainboardinit arch/i386/lib/id.inc
ldscript /arch/i386/lib/id.lds
-if USE_DCACHE_RAM
+if CONFIG_USE_DCACHE_RAM
mainboardinit cpu/via/car/cache_as_ram.inc
end
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
# failover.inc need definition in cpu_reset.inc, but we do not include
# cpu_reset.inc,so ...
# mainboardinit cpu/x86/fpu/enable_fpu.inc
# mainboardinit cpu/x86/mmx/enable_mmx.inc
-if USE_DCACHE_RAM
+if CONFIG_USE_DCACHE_RAM
if CONFIG_USE_INIT
initobject cache_as_ram_auto.o
else
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
+uses CONFIG_HAVE_MP_TABLE
uses CONFIG_CBFS
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_ROM_PAYLOAD
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_NRV2B
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses HAVE_MP_TABLE
-uses HAVE_ACPI_TABLES
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_HAVE_ACPI_TABLES
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
uses CONFIG_PCI_ROM_RUN
uses CONFIG_CONSOLE_VGA
uses CONFIG_MAX_PCI_BUSES
-uses TTYS0_BAUD
+uses CONFIG_TTYS0_BAUD
uses CONFIG_VIDEO_MB
uses CONFIG_IOAPIC
## New options
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
uses CONFIG_USE_INIT
#uses MAX_RAM_SLOTS
#uses USB_ENABLE
#uses VIACONFIG_VGA_PCI_14
## New options
-default USE_DCACHE_RAM = 1
-default DCACHE_RAM_BASE = 0xffef0000
-# default DCACHE_RAM_BASE = 0xffbf0000
-# default DCACHE_RAM_BASE = 0xfec00000 # HPET may use this.
-default DCACHE_RAM_SIZE = 8 * 1024
+default CONFIG_USE_DCACHE_RAM = 1
+default CONFIG_DCACHE_RAM_BASE = 0xffef0000
+# default CONFIG_DCACHE_RAM_BASE = 0xffbf0000
+# default CONFIG_DCACHE_RAM_BASE = 0xfec00000 # HPET may use this.
+default CONFIG_DCACHE_RAM_SIZE = 8 * 1024
default CONFIG_USE_INIT = 0
#default MAX_RAM_SLOTS = 2
#default USB_ENABLE = 1
#default VIACONFIG_VGA_PCI_10 = 0xf8000008
#default VIACONFIG_VGA_PCI_14 = 0xfc000000
-default ROM_SIZE = 512 * 1024
+default CONFIG_ROM_SIZE = 512 * 1024
default CONFIG_IOAPIC = 1
# Define framebuffer size of VX800's integrated graphics card.
default CONFIG_CONSOLE_SERIAL8250 = 1
default CONFIG_PCI_ROM_RUN = 0
default CONFIG_CONSOLE_VGA = 0
-default HAVE_FALLBACK_BOOT = 1
-default HAVE_MP_TABLE = 0
+default CONFIG_HAVE_FALLBACK_BOOT = 1
+default CONFIG_HAVE_MP_TABLE = 0
default CONFIG_UDELAY_TSC = 1
default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 1
-default HAVE_HARD_RESET = 0
-default HAVE_PIRQ_TABLE = 0
-default IRQ_SLOT_COUNT = 14
-default HAVE_ACPI_TABLES = 1
-default HAVE_OPTION_TABLE = 1
-default ROM_IMAGE_SIZE = 128 * 1024
-default FALLBACK_SIZE = ROM_SIZE
-default USE_FALLBACK_IMAGE = 1
-default STACK_SIZE = 16 * 1024
-default HEAP_SIZE = 20 * 1024
-# default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_HAVE_HARD_RESET = 0
+default CONFIG_HAVE_PIRQ_TABLE = 0
+default CONFIG_IRQ_SLOT_COUNT = 14
+default CONFIG_HAVE_ACPI_TABLES = 1
+default CONFIG_HAVE_OPTION_TABLE = 1
+default CONFIG_ROM_IMAGE_SIZE = 128 * 1024
+default CONFIG_FALLBACK_SIZE = CONFIG_ROM_SIZE
+default CONFIG_USE_FALLBACK_IMAGE = 1
+default CONFIG_STACK_SIZE = 16 * 1024
+default CONFIG_HEAP_SIZE = 20 * 1024
+# default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 0
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
-default CROSS_COMPILE = ""
-default CC = "$(CROSS_COMPILE)gcc -m32"
-default HOSTCC = "gcc"
+default CONFIG_CROSS_COMPILE = ""
+default CC = "$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC = "gcc"
default CONFIG_CBFS = 0
##
/*
* These four macros are copied from <arch/smp/mpspec.h>, I have to do this
- * since the "default HAVE_MP_TABLE = 0" in Options.lb, and also since
+ * since the "default CONFIG_HAVE_MP_TABLE = 0" in Options.lb, and also since
* mainboard/via/... have no mptable.c (so that I can not set
- * HAVE_MP_TABLE = 1) as many other mainboards.
+ * CONFIG_HAVE_MP_TABLE = 1) as many other mainboards.
* So I have to copy these four to here. acpi_fill_madt() needs this.
*/
#define MP_IRQ_POLARITY_HIGH 0x1
* around CLEAR_FIRST_1M_RAM and #include "cpu/x86/car/cache_as_ram_post.c".
* The CLEAR_FIRST_1M_RAM seems to make cpu/x86/car/cache_as_ram_post.c stop
* at somewhere, and cpu/x86/car/cache_as_ram_post.c do not cache my
- * $XIP_ROM_BASE+SIZE area.
+ * $CONFIG_XIP_ROM_BASE+SIZE area.
*
* Use #include "cpu/via/car/cache_as_ram_post.c". This version post.c have
* some diff with x86-version.
#include "cpu/via/car/cache_as_ram_post.c"
/* #include "cpu/x86/car/cache_as_ram_post.c" */
__asm__ volatile (
- /* Set new esp *//* before _RAMBASE */
+ /* Set new esp *//* before CONFIG_RAMBASE */
"subl %0, %%ebp\n\t"
"subl %0, %%esp\n\t"::
- "a" ((DCACHE_RAM_BASE + DCACHE_RAM_SIZE) - _RAMBASE)
+ "a" ((CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE) - CONFIG_RAMBASE)
);
{
const struct irq_routing_table intel_irq_routing_table = {
PIRQ_SIGNATURE, /* u32 signature */
PIRQ_VERSION, /* u16 version */
- 32 + 16 * IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
+ 32 + 16 * CONFIG_IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
0x00, /* Where the interrupt router lies (bus) */
(0x11 << 3) | 0x0, /* Where the interrupt router lies (dev) */
0xc20, /* IRQs devoted exclusively to PCI usage */
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
##
##
driver mainboard.o
-if HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
#object reset.o
##
## Romcc output
##
makerule ./failover.E
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./auto.E
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -E -mcpu=c3 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -E -mcpu=c3 -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -mcpu=c3 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -mcpu=c3 -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
##
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
### Things are delicate and we test to see if we should
### failover to another image.
###
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
irq 0x70 = 1
irq 0x72 = 12
end
- register "com1" = "{TTYS0_BAUD}"
+ register "com1" = "{CONFIG_TTYS0_BAUD}"
end
device pnp 2e.6 off end # CIR
device pnp 2e.7 off end # GAME_MIDI_GIPO1
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CBFS
-uses DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses HAVE_MP_TABLE
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
uses CONFIG_UDELAY_IO
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_ROM_PAYLOAD
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses HAVE_MP_TABLE
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
# logging
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
# logging
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
+default CONFIG_TTYS0_BAUD=115200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
-## ROM_SIZE is the size of boot ROM that this board will use.
-default ROM_SIZE = 256*1024
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
+default CONFIG_ROM_SIZE = 256*1024
###
### Build options
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## no MP table
##
-default HAVE_MP_TABLE=0
+default CONFIG_HAVE_MP_TABLE=0
##
## Build code to reset the motherboard from coreboot
##
-default HAVE_HARD_RESET=0
+default CONFIG_HAVE_HARD_RESET=0
##
## use io based udelay function
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=5
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=5
#object irq_tables.o
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
###
### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default ROM_IMAGE_SIZE = 65536
-default FALLBACK_SIZE = 131072
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
+default CONFIG_FALLBACK_SIZE = 131072
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE=0x4000
+default CONFIG_HEAP_SIZE=0x4000
##
## Only use the option table in a normal image
##
-#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
+#default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
##
## The default compiler
##
-default CROSS_COMPILE=""
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CONFIG_CROSS_COMPILE=""
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
arch i386 end
driver mainboard.o
-if HAVE_PIRQ_TABLE object irq_tables.o end
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_ACPI_TABLES
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_ACPI_TABLES
object fadt.o
object dsdt.o
object acpi_tables.o
end
makerule ./failover.E
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./failover.inc
- depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
- action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c ../romcc"
+ action "../romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
end
makerule ./auto.E
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -E -mcpu=c3 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -E -mcpu=c3 -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- depends "$(MAINBOARD)/auto.c option_table.h ../romcc"
- action "../romcc -mcpu=c3 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h ../romcc"
+ action "../romcc -mcpu=c3 -O -I$(TOP)/src -I. $(CPPFLAGS) $(CONFIG_MAINBOARD)/auto.c -o $@"
end
mainboardinit cpu/x86/16bit/entry16.inc
mainboardinit cpu/x86/32bit/entry32.inc
ldscript /cpu/x86/16bit/entry16.lds
ldscript /cpu/x86/32bit/entry32.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
mainboardinit arch/i386/lib/cpu_reset.inc
mainboardinit arch/i386/lib/id.inc
ldscript /arch/i386/lib/id.lds
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
mainboardinit ./failover.inc
end
uses CONFIG_SMP
uses CONFIG_CBFS
-uses HAVE_MP_TABLE
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
uses CONFIG_ROM_PAYLOAD
-uses IRQ_SLOT_COUNT
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_NRV2B
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses HAVE_MP_TABLE
-uses HAVE_ACPI_TABLES
-uses HAVE_ACPI_RESUME
-uses CROSS_COMPILE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_HAVE_ACPI_TABLES
+uses CONFIG_HAVE_ACPI_RESUME
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
uses CONFIG_PCI_ROM_RUN
uses CONFIG_CONSOLE_VGA
uses CONFIG_MAX_PCI_BUSES
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
uses CONFIG_VIDEO_MB
uses CONFIG_IOAPIC
-default ROM_SIZE = 512 * 1024
-default ROM_IMAGE_SIZE = 64 * 1024
-default FALLBACK_SIZE = ROM_SIZE
+default CONFIG_ROM_SIZE = 512 * 1024
+default CONFIG_ROM_IMAGE_SIZE = 64 * 1024
+default CONFIG_FALLBACK_SIZE = CONFIG_ROM_SIZE
default CONFIG_IOAPIC = 0
default CONFIG_VIDEO_MB = 32
default CONFIG_CONSOLE_SERIAL8250 = 1
default CONFIG_PCI_ROM_RUN = 0
default CONFIG_CONSOLE_VGA = 0
-default HAVE_FALLBACK_BOOT = 1
+default CONFIG_HAVE_FALLBACK_BOOT = 1
default CONFIG_SMP = 1
-default HAVE_MP_TABLE = 1
+default CONFIG_HAVE_MP_TABLE = 1
default CONFIG_UDELAY_TSC = 1
default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 1
-default HAVE_HARD_RESET = 0
-default HAVE_PIRQ_TABLE = 1
-default IRQ_SLOT_COUNT = 10
-default HAVE_ACPI_TABLES = 0
-default HAVE_OPTION_TABLE = 1
-default USE_FALLBACK_IMAGE = 1
-default MAINBOARD_VENDOR = "VIA"
-default MAINBOARD_PART_NUMBER = "pc2500e"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID = 0x1019
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID = 0xaa51
-default STACK_SIZE = 8 * 1024
-default HEAP_SIZE = 16 * 1024
-# default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 1
-default _RAMBASE = 0x00004000
+default CONFIG_HAVE_HARD_RESET = 0
+default CONFIG_HAVE_PIRQ_TABLE = 1
+default CONFIG_IRQ_SLOT_COUNT = 10
+default CONFIG_HAVE_ACPI_TABLES = 0
+default CONFIG_HAVE_OPTION_TABLE = 1
+default CONFIG_USE_FALLBACK_IMAGE = 1
+default CONFIG_MAINBOARD_VENDOR = "VIA"
+default CONFIG_MAINBOARD_PART_NUMBER = "pc2500e"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID = 0x1019
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID = 0xaa51
+default CONFIG_STACK_SIZE = 8 * 1024
+default CONFIG_HEAP_SIZE = 16 * 1024
+# default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 1
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
-default CROSS_COMPILE = ""
-default CC = "$(CROSS_COMPILE)gcc -m32 -fno-stack-protector"
-default HOSTCC = "gcc"
+default CONFIG_CROSS_COMPILE = ""
+default CC = "$(CONFIG_CROSS_COMPILE)gcc -m32 -fno-stack-protector"
+default CONFIG_HOSTCC = "gcc"
default CONFIG_MAX_PCI_BUSES = 3
default CONFIG_CONSOLE_SERIAL8250 = 1
-default TTYS0_BAUD = 115200
-default TTYS0_BASE = 0x3f8
-default TTYS0_LCS = 0x3
-default MAXIMUM_CONSOLE_LOGLEVEL = 9
-default DEFAULT_CONSOLE_LOGLEVEL = 9
+default CONFIG_TTYS0_BAUD = 115200
+default CONFIG_TTYS0_BASE = 0x3f8
+default CONFIG_TTYS0_LCS = 0x3
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
#
/* Enable multifunction for northbridge. */
pci_write_config8(ctrl.d0f0, 0x4f, 0x01);
- it8716f_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ it8716f_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
const struct irq_routing_table intel_irq_routing_table = {
PIRQ_SIGNATURE,
PIRQ_VERSION,
- 32 + 16 * IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
+ 32 + 16 * CONFIG_IRQ_SLOT_COUNT,/* Max. number of devices on the bus */
0x00, /* Interrupt router bus */
(0x11 << 3) | 0x0, /* Interrupt router device */
0x828, /* IRQs devoted exclusively to PCI usage */
## MA 02110-1301 USA
##
-## XIP_ROM_SIZE must be a power of 2.
-default XIP_ROM_SIZE = 64 * 1024
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+default CONFIG_XIP_ROM_SIZE = 64 * 1024
include /config/nofailovercalculation.lb
##
driver mainboard.o
-if HAVE_MP_TABLE
+if CONFIG_HAVE_MP_TABLE
object mptable.o
end
-if HAVE_PIRQ_TABLE
+if CONFIG_HAVE_PIRQ_TABLE
object irq_tables.o
end
-if HAVE_ACPI_TABLES
+if CONFIG_HAVE_ACPI_TABLES
object fadt.o
object acpi_tables.o
makerule dsdt.c
- depends "$(MAINBOARD)/dsdt.dsl"
- action "iasl -p dsdt -tc $(MAINBOARD)/dsdt.dsl"
+ depends "$(CONFIG_MAINBOARD)/dsdt.dsl"
+ action "iasl -p dsdt -tc $(CONFIG_MAINBOARD)/dsdt.dsl"
action "mv dsdt.hex dsdt.c"
end
object ./dsdt.o
## Romcc output
##
makerule ./auto.inc
- depends "$(MAINBOARD)/auto.c option_table.h"
- action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(MAINBOARD)/auto.c -o $@"
+ depends "$(CONFIG_MAINBOARD)/auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/auto.c -o $@"
action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
end
##
## Build our reset vector (This is where coreboot is entered)
##
-if USE_FALLBACK_IMAGE
+if CONFIG_USE_FALLBACK_IMAGE
mainboardinit cpu/x86/16bit/reset16.inc
ldscript /cpu/x86/16bit/reset16.lds
else
## MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
-uses HAVE_PIRQ_TABLE
-uses IRQ_SLOT_COUNT
-uses HAVE_ACPI_TABLES
-uses HAVE_OPTION_TABLE
-uses USE_OPTION_TABLE
-uses HAVE_LOW_TABLES
-
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses MAINBOARD
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PART_NUMBER
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_ACPI_TABLES
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_HAVE_LOW_TABLES
+
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
uses COREBOOT_EXTRA_VERSION
-uses ARCH
-uses FALLBACK_SIZE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_ARCH
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_COMPRESS
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_NRV2B
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
-uses PAYLOAD_SIZE
+uses CONFIG_PAYLOAD_SIZE
-uses _ROMBASE
-uses _RAMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
+uses CONFIG_ROMBASE
+uses CONFIG_RAMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
uses CONFIG_CBFS
# compiler specifics
-uses CROSS_COMPILE
+uses CONFIG_CROSS_COMPILE
uses CC
-uses HOSTCC
-uses OBJCOPY
+uses CONFIG_HOSTCC
+uses CONFIG_OBJCOPY
# Console specifics
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
uses CONFIG_UDELAY_TSC
uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
uses CONFIG_GDB_STUB
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
uses CONFIG_USE_PRINTK_IN_CAR
-## ROM_SIZE is the size of boot ROM that this board will use.
-default ROM_SIZE = 256*1024
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
+default CONFIG_ROM_SIZE = 256*1024
-default USE_DCACHE_RAM=1
-default DCACHE_RAM_BASE=0xffef0000
-#default DCACHE_RAM_BASE=0xffbf0000
-#default DCACHE_RAM_BASE=0xfec00000
-default DCACHE_RAM_SIZE=0x8000
+default CONFIG_USE_DCACHE_RAM=1
+default CONFIG_DCACHE_RAM_BASE=0xffef0000
+#default CONFIG_DCACHE_RAM_BASE=0xffbf0000
+#default CONFIG_DCACHE_RAM_BASE=0xfec00000
+default CONFIG_DCACHE_RAM_SIZE=0x8000
default CONFIG_USE_PRINTK_IN_CAR=1
###
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
## Use TSC for udelay.
##
## Build code to reset the motherboard from linuxBIOS
##
-default HAVE_HARD_RESET=1
+default CONFIG_HAVE_HARD_RESET=1
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=15
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=15
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
##
## Build code to load acpi tables
##
-default HAVE_ACPI_TABLES=1
+default CONFIG_HAVE_ACPI_TABLES=1
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
##
## Build code to fill in tables both in low and high memory
##
-default HAVE_LOW_TABLES=1
+default CONFIG_HAVE_LOW_TABLES=1
##
### LinuxBIOS layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy.
-default ROM_IMAGE_SIZE = 65536
-default FALLBACK_SIZE = ROM_IMAGE_SIZE
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
+default CONFIG_FALLBACK_SIZE = CONFIG_ROM_IMAGE_SIZE
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE=0x4000
+default CONFIG_HEAP_SIZE=0x4000
##
## Only use the option table in a normal image
##
-#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-default USE_OPTION_TABLE = 0
+#default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = 0
-default _RAMBASE = 0x00004000
+default CONFIG_RAMBASE = 0x00004000
default CONFIG_ROM_PAYLOAD = 1
##
## The default compiler
##
-default CROSS_COMPILE=""
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
+default CONFIG_CROSS_COMPILE=""
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default CONFIG_HOSTCC="gcc"
##
## Set this to the max PCI bus number you
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
## Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=5
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=5
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=5
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=5
#
# CBFS
const struct irq_routing_table intel_irq_routing_table = {
PIRQ_SIGNATURE, /* u32 signature */
PIRQ_VERSION, /* u16 version */
- 32 + 16 * IRQ_SLOT_COUNT, /* There can be total 15 devices on the bus */
+ 32 + 16 * CONFIG_IRQ_SLOT_COUNT, /* There can be total 15 devices on the bus */
0x00, /* Where the interrupt router lies (bus) */
(0x11 << 3) | 0x0, /* Where the interrupt router lies (dev) */
0xc20, /* IRQs devoted exclusively to PCI usage */
# Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
#
-uses AGP_APERTURE_SIZE
-uses HAVE_ACPI_TABLES
-uses HAVE_HIGH_TABLES
+uses CONFIG_AGP_APERTURE_SIZE
+uses CONFIG_HAVE_ACPI_TABLES
+uses CONFIG_HAVE_HIGH_TABLES
-default AGP_APERTURE_SIZE=0x4000000
-default HAVE_HIGH_TABLES=1
+default CONFIG_AGP_APERTURE_SIZE=0x4000000
+default CONFIG_HAVE_HIGH_TABLES=1
config chip.h
driver northbridge.o
driver misc_control.o
-if HAVE_ACPI_TABLES
+if CONFIG_HAVE_ACPI_TABLES
object amdfam10_acpi.o
makerule ssdt.c
depends "$(TOP)/src/northbridge/amd/amdfam10/ssdt.dsl"
#ifdef __ROMCC__
#if NODE_NUMS==64
- #define NODE_PCI(x, fn) ((x<32)?(PCI_DEV(CBB,(CDB+x),fn)):(PCI_DEV((CBB-1),(CDB+x-32),fn)))
+ #define NODE_PCI(x, fn) ((x<32)?(PCI_DEV(CONFIG_CBB,(CONFIG_CDB+x),fn)):(PCI_DEV((CONFIG_CBB-1),(CONFIG_CDB+x-32),fn)))
#else
- #define NODE_PCI(x, fn) PCI_DEV(CBB,(CDB+x),fn)
+ #define NODE_PCI(x, fn) PCI_DEV(CONFIG_CBB,(CONFIG_CDB+x),fn)
#endif
#endif
//#define MEM_CS_COPY 1
#define MEM_CS_COPY NODE_NUMS
-#if MEM_TRAIN_SEQ == 0
+#if CONFIG_MEM_TRAIN_SEQ == 0
#define DQS_DELAY_COPY NODE_NUMS
#else
// #define DQS_DELAY_COPY 1
/* fill the first 8 byte with that num */
/* fill the next num*num byte with distance, local is 10, 1 hop mean 20, and 2 hop with 30.... */
- struct sys_info *sysinfox = (struct sys_info *)((CONFIG_LB_MEM_TOPK<<10) - DCACHE_RAM_GLOBAL_VAR_SIZE);
+ struct sys_info *sysinfox = (struct sys_info *)((CONFIG_LB_MEM_TOPK<<10) - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE);
u8 *ln = sysinfox->ln;
u8 *CBST;
u8 *CBBX;
u8 *CBS2;
- u8 *CBB2;
+ u8 *CONFIG_CBB2;
int i;
HCDN = ssdt+0x57a; //+5 will be next HCDN
CBBX = ssdt+0x61f; //
CBST = ssdt+0x626;
- CBB2 = ssdt+0x62d; //
+ CONFIG_CBB2 = ssdt+0x62d; //
CBS2 = ssdt+0x634;
for(i=0;i<HC_NUMS;i++) {
int_to_stream(0x20202020, HCDN + i*5);
}
- *CBBX = (u8)(CBB);
+ *CBBX = (u8)(CONFIG_CBB);
- if(CBB == 0xff) {
+ if(CONFIG_CBB == 0xff) {
*CBST = (u8) (0x0f);
} else {
if((sysconf.pci1234[0] >> 12) & 0xff) { //sb chain on other than bus 0
}
}
- if((CBB == 0xff) && (sysconf.nodes>32)) {
+ if((CONFIG_CBB == 0xff) && (sysconf.nodes>32)) {
*CBS2 = 0x0f;
- *CBB2 = (u8)(CBB-1);
+ *CONFIG_CBB2 = (u8)(CONFIG_CBB-1);
} else {
*CBS2 = 0x00;
- *CBB2 = 0x00;
+ *CONFIG_CBB2 = 0x00;
}
}
device_t dev;
struct dram_base_mask_t d;
#if defined(__ROMCC__)
- dev = PCI_DEV(CBB, CDB, 1);
+ dev = PCI_DEV(CONFIG_CBB, CONFIG_CDB, 1);
#else
dev = __f1_dev[0];
#endif
-#if EXT_CONF_SUPPORT == 1
+#if CONFIG_EXT_CONF_SUPPORT == 1
// I will use ext space only for simple
pci_write_config32(dev, 0x110, nodeid | (1<<28)); // [47:27] at [28:8]
d.mask = pci_read_config32(dev, 0x114); // enable is bit 0
{
u32 i;
device_t dev;
-#if EXT_CONF_SUPPORT == 1
+#if CONFIG_EXT_CONF_SUPPORT == 1
// I will use ext space only for simple
u32 d_base_i, d_base_d, d_mask_i, d_mask_d;
d_base_i = nodeid | (0<<28);
dev = __f1_dev[i];
#endif
-#if EXT_CONF_SUPPORT == 1
+#if CONFIG_EXT_CONF_SUPPORT == 1
// I will use ext space only for simple
pci_write_config32(dev, 0x110, d_base_i);
pci_write_config32(dev, 0x114, d_base_d); //[47:27] at [28:8];
return one_DCT;
}
#endif
-#if HW_MEM_HOLE_SIZEK != 0
+#if CONFIG_HW_MEM_HOLE_SIZEK != 0
static u32 hoist_memory(u32 hole_startk, u32 i, u32 one_DCT, u32 nodes)
{
#endif
-#if EXT_CONF_SUPPORT
+#if CONFIG_EXT_CONF_SUPPORT
static void set_addr_map_reg_4_6_in_one_node(u32 nodeid, u32 cfg_map_dest,
u32 busn_min, u32 busn_max,
u32 type)
busn_min>>=segbit;
busn_max>>=segbit;
-#if EXT_CONF_SUPPORT
+#if CONFIG_EXT_CONF_SUPPORT
if(ht_c_index < 4) {
#endif
tempreg = 3 | ((nodeid&0xf)<<4) | ((nodeid & 0x30)<<(12-4))|(linkn<<8)|((busn_min & 0xff)<<16)|((busn_max&0xff)<<24);
#endif
pci_write_config32(dev, 0xe0 + ht_c_index * 4, tempreg);
}
-#if EXT_CONF_SUPPORT
+#if CONFIG_EXT_CONF_SUPPORT
return;
}
u32 i;
device_t dev;
-#if EXT_CONF_SUPPORT
+#if CONFIG_EXT_CONF_SUPPORT
if(ht_c_index<4) {
#endif
for(i=0; i<nodes; i++) {
#endif
pci_write_config32(dev, 0xe0 + ht_c_index * 4, 0);
}
-#if EXT_CONF_SUPPORT
+#if CONFIG_EXT_CONF_SUPPORT
return;
}
}
-#if PCI_BUS_SEGN_BITS
+#if CONFIG_PCI_BUS_SEGN_BITS
static u32 check_segn(device_t dev, u32 segbusn, u32 nodes,
sys_info_conf_t *sysinfo)
{
u32 tempreg;
device_t dev;
-#if EXT_CONF_SUPPORT
+#if CONFIG_EXT_CONF_SUPPORT
if(ht_c_index<4) {
#endif
/* io range allocation */
#endif
pci_write_config32(dev, 0xC0 + ht_c_index * 8, tempreg);
}
-#if EXT_CONF_SUPPORT
+#if CONFIG_EXT_CONF_SUPPORT
return;
}
{
u32 i;
device_t dev;
-#if EXT_CONF_SUPPORT
+#if CONFIG_EXT_CONF_SUPPORT
if(ht_c_index<4) {
#endif
/* io range allocation */
pci_write_config32(dev, 0xC4 + ht_c_index * 8, 0);
pci_write_config32(dev, 0xC0 + ht_c_index * 8, 0);
}
-#if EXT_CONF_SUPPORT
+#if CONFIG_EXT_CONF_SUPPORT
return;
}
// : if hc_c_index > 3, We should use io_min, io_max to clear extend space
pci_write_config32(dev, 0xe0 + ht_c_index * 4, 0);
}
}
-#if EXT_CONF_SUPPORT
+#if CONFIG_EXT_CONF_SUPPORT
u32 j;
// clear the extend space
for(j = 0; j< nodes; j++) {
tempreg = 3 | ((nodeid & 0xf) <<4) | ((nodeid & 0x30)<<(12-4)) | (linkn<<8);
for(ht_c_index=0;ht_c_index<4; ht_c_index++) {
- reg = pci_read_config32(PCI_DEV(CBB, CDB, 1), 0xe0 + ht_c_index * 4);
+ reg = pci_read_config32(PCI_DEV(CONFIG_CBB, CONFIG_CDB, 1), 0xe0 + ht_c_index * 4);
if(((reg & 0xffff) == 0x0000)) { /*found free*/
break;
}
static void set_BusSegmentEn(u32 node, u32 segbit)
{
-#if PCI_BUS_SEGN_BITS
+#if CONFIG_PCI_BUS_SEGN_BITS
u32 dword;
device_t dev;
u32 io_min, u32 io_max)
{
u32 val;
-#if EXT_CONF_SUPPORT
+#if CONFIG_EXT_CONF_SUPPORT
if(reg!=0x110) {
#endif
/* io range allocation */
index = (reg-0xc0)>>3;
-#if EXT_CONF_SUPPORT
+#if CONFIG_EXT_CONF_SUPPORT
} else {
index+=4;
}
u32 mmio_min, u32 mmio_max)
{
u32 val;
-#if EXT_CONF_SUPPORT
+#if CONFIG_EXT_CONF_SUPPORT
if(reg!=0x110) {
#endif
/* io range allocation */
index = (reg-0x80)>>3;
-#if EXT_CONF_SUPPORT
+#if CONFIG_EXT_CONF_SUPPORT
} else {
index+=8;
}
u32 i;
u32 tempreg;
-#if EXT_CONF_SUPPORT
+#if CONFIG_EXT_CONF_SUPPORT
if(reg!=0x110) {
#endif
/* io range allocation */
#endif
for(i=0; i<sysconf.nodes; i++)
pci_write_config32(__f1_dev[i], reg, tempreg);
-#if EXT_CONF_SUPPORT
+#if CONFIG_EXT_CONF_SUPPORT
return;
}
u32 i;
u32 tempreg;
-#if EXT_CONF_SUPPORT
+#if CONFIG_EXT_CONF_SUPPORT
if(reg!=0x110) {
#endif
/* io range allocation */
tempreg = 3 | (nodeid & 0x30) | (mmio_min&0xffffff00);
for(i=0; i<sysconf.nodes; i++)
pci_write_config32(__f1_dev[i], reg, tempreg);
-#if EXT_CONF_SUPPORT
+#if CONFIG_EXT_CONF_SUPPORT
return;
}
static void print_debug_pci_dev(u32 dev)
{
-#if PCI_BUS_SEGN_BITS==0
+#if CONFIG_PCI_BUS_SEGN_BITS==0
printk_debug("PCI: %02x:%02x.%02x", (dev>>20) & 0xff, (dev>>15) & 0x1f, (dev>>12) & 0x7);
#else
printk_debug("PCI: %04x:%02x:%02x.%02x", (dev>>28) & 0x0f, (dev>>20) & 0xff, (dev>>15) & 0x1f, (dev>>12) & 0x7);
// mmconf is not ready yet
static void set_bsp_node_CHtExtNodeCfgEn(void)
{
-#if EXT_RT_TBL_SUPPORT == 1
+#if CONFIG_EXT_RT_TBL_SUPPORT == 1
u32 dword;
dword = pci_io_read_config32(PCI_DEV(0, 0x18, 0), 0x68);
dword |= (1<<27) | (1<<25);
/* CHtExtAddrEn */
pci_io_write_config32(PCI_DEV(0, 0x18, 0), 0x68, dword);
- // CPU on bus 0xff and 0xfe now. For now on we can use CBB and CDB.
+ // CPU on bus 0xff and 0xfe now. For now on we can use CONFIG_CBB and CONFIG_CDB.
#endif
}
static void enumerate_ht_chain(void)
{
-#if HT_CHAIN_UNITID_BASE != 0
-/* HT_CHAIN_UNITID_BASE could be 0 (only one ht device in the ht chain),
+#if CONFIG_HT_CHAIN_UNITID_BASE != 0
+/* CONFIG_HT_CHAIN_UNITID_BASE could be 0 (only one ht device in the ht chain),
if so, don't need to go through the chain */
/* Assumption the HT chain that is bus 0 has the HT I/O Hub on it.
* links needs to be programed to point at bus 0.
*/
unsigned next_unitid, last_unitid = 0;
-#if HT_CHAIN_END_UNITID_BASE != 0x20
+#if CONFIG_HT_CHAIN_END_UNITID_BASE != 0x20
// let't record the device of last ht device, So we can set the
- // Unitid to HT_CHAIN_END_UNITID_BASE
+ // Unitid to CONFIG_HT_CHAIN_END_UNITID_BASE
unsigned real_last_unitid = 0;
u8 real_last_pos = 0;
int ht_dev_num = 0; // except host_bridge
u8 end_used = 0;
#endif
- next_unitid = HT_CHAIN_UNITID_BASE;
+ next_unitid = CONFIG_HT_CHAIN_UNITID_BASE;
do {
u32 id;
u8 hdr_type, pos;
unsigned ctrl, ctrl_off;
device_t devx;
-#if HT_CHAIN_END_UNITID_BASE != 0x20
+#if CONFIG_HT_CHAIN_END_UNITID_BASE != 0x20
if(next_unitid>=0x18) {
if(!end_used) {
- next_unitid = HT_CHAIN_END_UNITID_BASE;
+ next_unitid = CONFIG_HT_CHAIN_END_UNITID_BASE;
end_used = 1;
} else {
goto out;
real_last_pos = pos;
ht_dev_num++ ;
#endif
- #if HT_CHAIN_END_UNITID_BASE == 0
+ #if CONFIG_HT_CHAIN_END_UNITID_BASE == 0
if (!next_unitid)
goto out;
#endif
} while(last_unitid != next_unitid);
out: ;
-#if HT_CHAIN_END_UNITID_BASE != 0x20
- if((ht_dev_num>1) && (real_last_unitid != HT_CHAIN_END_UNITID_BASE) && !end_used) {
+#if CONFIG_HT_CHAIN_END_UNITID_BASE != 0x20
+ if((ht_dev_num>1) && (real_last_unitid != CONFIG_HT_CHAIN_END_UNITID_BASE) && !end_used) {
u16 flags;
flags = pci_io_read_config16(PCI_DEV(0,real_last_unitid,0), real_last_pos + PCI_CAP_FLAGS);
flags &= ~0x1f;
- flags |= HT_CHAIN_END_UNITID_BASE & 0x1f;
+ flags |= CONFIG_HT_CHAIN_END_UNITID_BASE & 0x1f;
pci_io_write_config16(PCI_DEV(0, real_last_unitid, 0), real_last_pos + PCI_CAP_FLAGS, flags);
}
#endif
* reset HC_POSSIBLE_NUM and update ssdt.dsl (hcdn, hclk)
*
* Put all the possible ht node/link to the list tp pci1234[] in get_bus_conf.c
- * on MB dir. Also, don't forget to increase the ACPI_SSDTX_NUM etc if you have
+ * on MB dir. Also, don't forget to increase the CONFIG_ACPI_SSDTX_NUM etc if you have
* too much SSDT. How about co-processor on socket 1 on 2 way system.
* or socket 2, and socket3 on 4 way system? treat that as one hc too!
*
pci_dev_read_resources(dev);
/* If we are not the first processor don't allocate the gart apeture */
- if (dev->path.pci.devfn != PCI_DEVFN(CDB, 3)) {
+ if (dev->path.pci.devfn != PCI_DEVFN(CONFIG_CDB, 3)) {
return;
}
if (iommu) {
/* Add a Gart apeture resource */
resource = new_resource(dev, 0x94);
- resource->size = iommu?AGP_APERTURE_SIZE:1;
+ resource->size = iommu?CONFIG_AGP_APERTURE_SIZE:1;
resource->align = log2(resource->size);
resource->gran = log2(resource->size);
resource->limit = 0xffffffff; /* 4G */
#include "amdfam10.h"
-#if HW_MEM_HOLE_SIZEK != 0
+#if CONFIG_HW_MEM_HOLE_SIZEK != 0
#include <cpu/amd/model_10xxx_rev.h>
#endif
{
#if NODE_NUMS == 64
if(nodeid<32) {
- return dev_find_slot(CBB, PCI_DEVFN(CDB + nodeid, fn));
+ return dev_find_slot(CONFIG_CBB, PCI_DEVFN(CONFIG_CDB + nodeid, fn));
} else {
- return dev_find_slot(CBB-1, PCI_DEVFN(CDB + nodeid - 32, fn));
+ return dev_find_slot(CONFIG_CBB-1, PCI_DEVFN(CONFIG_CDB + nodeid - 32, fn));
}
#else
- return dev_find_slot(CBB, PCI_DEVFN(CDB + nodeid, fn));
+ return dev_find_slot(CONFIG_CBB, PCI_DEVFN(CONFIG_CDB + nodeid, fn));
#endif
}
__f4_dev[i] = get_node_pci(i, 4);
}
if (!__f1_dev[0]) {
- printk_err("Cannot find %02x:%02x.1", CBB, CDB);
+ printk_err("Cannot find %02x:%02x.1", CONFIG_CBB, CONFIG_CDB);
die("Cannot go on\n");
}
}
#if NODE_NUMS == 64
unsigned busn;
busn = dev->bus->secondary;
- if(busn != CBB) {
- return (dev->path.pci.devfn >> 3) - CDB + 32;
+ if(busn != CONFIG_CBB) {
+ return (dev->path.pci.devfn >> 3) - CONFIG_CDB + 32;
} else {
- return (dev->path.pci.devfn >> 3) - CDB;
+ return (dev->path.pci.devfn >> 3) - CONFIG_CDB;
}
#else
- return (dev->path.pci.devfn >> 3) - CDB;
+ return (dev->path.pci.devfn >> 3) - CONFIG_CDB;
#endif
}
u32 busn = max&0xff;
u32 max_devfn;
-#if HT3_SUPPORT==1
+#if CONFIG_HT3_SUPPORT==1
if(is_sublink1) {
u32 regpos;
u32 reg;
*/
ht_c_index = get_ht_c_index(nodeid, link, &sysconf);
-#if EXT_CONF_SUPPORT == 0
+#if CONFIG_EXT_CONF_SUPPORT == 0
if(ht_c_index>=4) return max;
#endif
* so we set the subordinate bus number to 0xff for the moment.
*/
-#if SB_HT_CHAIN_ON_BUS0 > 0
+#if CONFIG_SB_HT_CHAIN_ON_BUS0 > 0
// first chain will on bus 0
if((nodeid == 0) && (sblink==link)) { // actually max is 0 here
min_bus = max;
}
- #if SB_HT_CHAIN_ON_BUS0 > 1
+ #if CONFIG_SB_HT_CHAIN_ON_BUS0 > 1
// second chain will be on 0x40, third 0x80, forth 0xc0
// i would refined that to 2, 3, 4 ==> 0, 0x, 40, 0x80, 0xc0
// >4 will use more segments, We can have 16 segmment and every segment have 256 bus, For that case need the kernel support mmio pci config.
// Put sb chain in bus 0
-#if SB_HT_CHAIN_ON_BUS0 > 0
+#if CONFIG_SB_HT_CHAIN_ON_BUS0 > 0
if(nodeid==0) {
- #if ((HT_CHAIN_UNITID_BASE != 1) || (HT_CHAIN_END_UNITID_BASE != 0x20))
+ #if ((CONFIG_HT_CHAIN_UNITID_BASE != 1) || (CONFIG_HT_CHAIN_END_UNITID_BASE != 0x20))
offset_unitid = 1;
#endif
max = amdfam10_scan_chain(dev, nodeid, sblink, sblink, max, offset_unitid ); // do sb ht chain at first, in case s2885 put sb chain (8131/8111) on link2, but put 8151 on link0
#endif
-#if PCI_BUS_SEGN_BITS
+#if CONFIG_PCI_BUS_SEGN_BITS
max = check_segn(dev, max, sysconf.nodes, &sysconf);
#endif
for(link = 0; link < dev->links; link++) {
-#if SB_HT_CHAIN_ON_BUS0 > 0
+#if CONFIG_SB_HT_CHAIN_ON_BUS0 > 0
if( (nodeid == 0) && (sblink == link) ) continue; //already done
#endif
offset_unitid = 0;
- #if ((HT_CHAIN_UNITID_BASE != 1) || (HT_CHAIN_END_UNITID_BASE != 0x20))
- #if SB_HT_CHAIN_UNITID_OFFSET_ONLY == 1
+ #if ((CONFIG_HT_CHAIN_UNITID_BASE != 1) || (CONFIG_HT_CHAIN_END_UNITID_BASE != 0x20))
+ #if CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY == 1
if((nodeid == 0) && (sblink == link))
#endif
offset_unitid = 1;
resource = amdfam10_find_iopair(dev, nodeid, link);
if (resource) {
u32 align;
-#if EXT_CONF_SUPPORT == 1
+#if CONFIG_EXT_CONF_SUPPORT == 1
if((resource->index & 0x1fff) == 0x1110) { // ext
align = 8;
}
IORESOURCE_MEM | IORESOURCE_PREFETCH,
IORESOURCE_MEM | IORESOURCE_PREFETCH);
-#if EXT_CONF_SUPPORT == 1
+#if CONFIG_EXT_CONF_SUPPORT == 1
if((resource->index & 0x1fff) == 0x1110) { // ext
normalize_resource(resource);
}
IORESOURCE_MEM | IORESOURCE_PREFETCH,
IORESOURCE_MEM);
-#if EXT_CONF_SUPPORT == 1
+#if CONFIG_EXT_CONF_SUPPORT == 1
if((resource->index & 0x1fff) == 0x1110) { // ext
normalize_resource(resource);
}
#define BRIDGE_IO_MASK (IORESOURCE_IO | IORESOURCE_MEM | IORESOURCE_PREFETCH)
#endif
-#if HW_MEM_HOLE_SIZEK != 0
+#if CONFIG_HW_MEM_HOLE_SIZEK != 0
struct hw_mem_hole_info {
unsigned hole_startk;
struct hw_mem_hole_info mem_hole;
int i;
- mem_hole.hole_startk = HW_MEM_HOLE_SIZEK;
+ mem_hole.hole_startk = CONFIG_HW_MEM_HOLE_SIZEK;
mem_hole.node_id = -1;
for (i = 0; i < sysconf.nodes; i++) {
u32 hole_sizek;
u32 one_DCT;
- struct sys_info *sysinfox = (struct sys_info *)((CONFIG_LB_MEM_TOPK<<10) - DCACHE_RAM_GLOBAL_VAR_SIZE); // in RAM
+ struct sys_info *sysinfox = (struct sys_info *)((CONFIG_LB_MEM_TOPK<<10) - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE); // in RAM
struct mem_info *meminfo;
meminfo = &sysinfox->meminfo[i];
#endif
-#if HAVE_HIGH_TABLES==1
+#if CONFIG_HAVE_HIGH_TABLES==1
#define HIGH_TABLES_SIZE 64 // maximum size of high tables in KB
extern uint64_t high_tables_base, high_tables_size;
#endif
u32 pci_tolm;
int i, idx;
u32 link;
-#if HW_MEM_HOLE_SIZEK != 0
+#if CONFIG_HW_MEM_HOLE_SIZEK != 0
struct hw_mem_hole_info mem_hole;
u32 reset_memhole = 1;
#endif
/* Round the mmio hold to 64M */
mmio_basek &= ~((64*1024) - 1);
-#if HW_MEM_HOLE_SIZEK != 0
+#if CONFIG_HW_MEM_HOLE_SIZEK != 0
/* if the hw mem hole is already set in raminit stage, here we will compare
* mmio_basek and hole_basek. if mmio_basek is bigger that hole_basek and will
* use hole_basek as mmio_basek and we don't need to reset hole.
if(reset_memhole) {
if(mem_hole.node_id!=-1) {
- /* We need to select HW_MEM_HOLE_SIZEK for raminit, it can not
+ /* We need to select CONFIG_HW_MEM_HOLE_SIZEK for raminit, it can not
make hole_startk to some basek too!
We need to reset our Mem Hole, because We want more big HOLE
than we already set
disable_hoist_memory(mem_hole.hole_startk, mem_hole.node_id);
}
- #if HW_MEM_HOLE_SIZE_AUTO_INC == 1
+ #if CONFIG_HW_MEM_HOLE_SIZE_AUTO_INC == 1
// We need to double check if the mmio_basek is valid for hole
// setting, if it is equal to basek, we need to decrease it some
resource_t basek_pri;
ram_resource(dev, (idx | i), basek, pre_sizek);
idx += 0x10;
sizek -= pre_sizek;
-#if HAVE_HIGH_TABLES==1
+#if CONFIG_HAVE_HIGH_TABLES==1
if (i==0 && high_tables_base==0) {
/* Leave some space for ACPI, PIRQ and MP tables */
high_tables_base = (mmio_basek - HIGH_TABLES_SIZE) * 1024;
#endif
}
#if CONFIG_AMDMCT == 0
- #if HW_MEM_HOLE_SIZEK != 0
+ #if CONFIG_HW_MEM_HOLE_SIZEK != 0
if(reset_memhole) {
- struct sys_info *sysinfox = (struct sys_info *)((CONFIG_LB_MEM_TOPK<<10) - DCACHE_RAM_GLOBAL_VAR_SIZE); // in RAM
+ struct sys_info *sysinfox = (struct sys_info *)((CONFIG_LB_MEM_TOPK<<10) - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE); // in RAM
struct mem_info *meminfo;
meminfo = &sysinfox->meminfo[i];
sizek += hoist_memory(mmio_basek,i, get_one_DCT(meminfo), sysconf.nodes);
}
ram_resource(dev, (idx | i), basek, sizek);
idx += 0x10;
-#if HAVE_HIGH_TABLES==1
+#if CONFIG_HAVE_HIGH_TABLES==1
printk_debug("%d: mmio_basek=%08lx, basek=%08x, limitk=%08x\n",
i, mmio_basek, basek, limitk);
if (i==0 && high_tables_base==0) {
for(reg = 0xe0; reg <= 0xec; reg += 4) {
f1_write_config32(reg, 0);
}
-#if EXT_CONF_SUPPORT == 1
+#if CONFIG_EXT_CONF_SUPPORT == 1
// all nodes
for(i = 0; i< sysconf.nodes; i++) {
int index;
for(i=0;i<dev->links;i++) {
- max = pci_scan_bus(&dev->link[i], PCI_DEVFN(CDB, 0), 0xff, max);
+ max = pci_scan_bus(&dev->link[i], PCI_DEVFN(CONFIG_CDB, 0), 0xff, max);
}
/* Tune the hypertransport transaction for best performance.
.enable_resources = enable_childrens_resources,
.init = 0,
.scan_bus = pci_domain_scan_bus,
-#if MMCONF_SUPPORT_DEFAULT
+#if CONFIG_MMCONF_SUPPORT_DEFAULT
.ops_pci_bus = &pci_ops_mmconf,
#else
.ops_pci_bus = &pci_cf8_conf1,
sysconf.bsp_apicid = lapicid();
sysconf.apicid_offset = sysconf.bsp_apicid;
-#if (ENABLE_APIC_EXT_ID == 1)
+#if (CONFIG_ENABLE_APIC_EXT_ID == 1)
if (pci_read_config32(dev, 0x68) & (HTTC_APIC_EXT_ID|HTTC_APIC_EXT_BRD_CST))
{
sysconf.enabled_apic_ext_id = 1;
}
- #if (APIC_ID_OFFSET>0)
+ #if (CONFIG_APIC_ID_OFFSET>0)
if(sysconf.enabled_apic_ext_id) {
if(sysconf.bsp_apicid == 0) {
/* bsp apic id is not changed */
- sysconf.apicid_offset = APIC_ID_OFFSET;
+ sysconf.apicid_offset = CONFIG_APIC_ID_OFFSET;
} else {
sysconf.lift_bsp_apicid = 1;
}
nb_cfg_54 = read_nb_cfg_54();
-#if CBB
- dev_mc = dev_find_slot(0, PCI_DEVFN(CDB, 0)); //0x00
+#if CONFIG_CBB
+ dev_mc = dev_find_slot(0, PCI_DEVFN(CONFIG_CDB, 0)); //0x00
if(dev_mc && dev_mc->bus) {
printk_debug("%s found", dev_path(dev_mc));
pci_domain = dev_mc->bus->dev;
if(pci_domain && (pci_domain->path.type == DEVICE_PATH_PCI_DOMAIN)) {
printk_debug("\n%s move to ",dev_path(dev_mc));
- dev_mc->bus->secondary = CBB; // move to 0xff
+ dev_mc->bus->secondary = CONFIG_CBB; // move to 0xff
printk_debug("%s",dev_path(dev_mc));
} else {
printk_debug("\n");
}
- dev_mc = dev_find_slot(CBB, PCI_DEVFN(CDB, 0));
+ dev_mc = dev_find_slot(CONFIG_CBB, PCI_DEVFN(CONFIG_CDB, 0));
if(!dev_mc) {
dev_mc = dev_find_slot(0, PCI_DEVFN(0x18, 0));
if (dev_mc && dev_mc->bus) {
if(pci_domain && (pci_domain->path.type == DEVICE_PATH_PCI_DOMAIN)) {
if((pci_domain->links==1) && (pci_domain->link[0].children == dev_mc)) {
printk_debug("%s move to ",dev_path(dev_mc));
- dev_mc->bus->secondary = CBB; // move to 0xff
+ dev_mc->bus->secondary = CONFIG_CBB; // move to 0xff
printk_debug("%s\n",dev_path(dev_mc));
while(dev_mc){
printk_debug("%s move to ",dev_path(dev_mc));
#endif
- dev_mc = dev_find_slot(CBB, PCI_DEVFN(CDB, 0));
+ dev_mc = dev_find_slot(CONFIG_CBB, PCI_DEVFN(CONFIG_CDB, 0));
if (!dev_mc) {
- printk_err("%02x:%02x.0 not found", CBB, CDB);
+ printk_err("%02x:%02x.0 not found", CONFIG_CBB, CONFIG_CDB);
die("");
}
nodes = sysconf.nodes;
-#if CBB && (NODE_NUMS > 32)
+#if CONFIG_CBB && (NODE_NUMS > 32)
if(nodes>32) { // need to put node 32 to node 63 to bus 0xfe
if(pci_domain->links==1) {
pci_domain->links++; // from 1 to 2
pci_domain->link[1].children = 0;
printk_debug("%s links increase to %d\n", dev_path(pci_domain), pci_domain->links);
}
- pci_domain->link[1].secondary = CBB - 1;
+ pci_domain->link[1].secondary = CONFIG_CBB - 1;
}
#endif
/* Find which cpus are present */
unsigned busn, devn;
struct bus *pbus;
- busn = CBB;
- devn = CDB+i;
+ busn = CONFIG_CBB;
+ devn = CONFIG_CDB+i;
pbus = dev_mc->bus;
-#if CBB && (NODE_NUMS > 32)
+#if CONFIG_CBB && (NODE_NUMS > 32)
if(i>=32) {
busn--;
devn-=32;
*/
int j;
int linknum;
-#if HT3_SUPPORT==1
+#if CONFIG_HT3_SUPPORT==1
linknum = 8;
#else
linknum = 4;
if (cpu) {
cpu->path.apic.node_id = i;
cpu->path.apic.core_id = j;
- #if (ENABLE_APIC_EXT_ID == 1) && (APIC_ID_OFFSET>0)
+ #if (CONFIG_ENABLE_APIC_EXT_ID == 1) && (CONFIG_APIC_ID_OFFSET>0)
if(sysconf.enabled_apic_ext_id) {
if(sysconf.lift_bsp_apicid) {
cpu->path.apic.apic_id += sysconf.apicid_offset;
#define RAMINIT_H
#if 0
-#if DIMM_SUPPORT==0x0110
+#if CONFIG_DIMM_SUPPORT==0x0110
//FBDIMM REG
/* each channel can have 8 fbdimm */
#define DIMM_SOCKETS 8
#endif
#endif
-//#if (DIMM_SUPPORT & 0x00ff)==0x0004
+//#if (CONFIG_DIMM_SUPPORT & 0x00ff)==0x0004
//DDR2 REG and unbuffered : Socket F 1027 and AM3
/* every channel have 4 DDR2 DIMM for socket F
* 2 for socket M2/M3
void mctSMBhub_Init(u32 node)
{
- struct sys_info *sysinfo = (struct sys_info *)(DCACHE_RAM_BASE + DCACHE_RAM_SIZE - DCACHE_RAM_GLOBAL_VAR_SIZE);
+ struct sys_info *sysinfo = (struct sys_info *)(CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE);
struct mem_controller *ctrl = &( sysinfo->ctrl[node] );
activate_spd_rom(ctrl);
}
void mctGet_DIMMAddr(struct DCTStatStruc *pDCTstat, u32 node)
{
int j;
- struct sys_info *sysinfo = (struct sys_info *)(DCACHE_RAM_BASE + DCACHE_RAM_SIZE - DCACHE_RAM_GLOBAL_VAR_SIZE);
+ struct sys_info *sysinfo = (struct sys_info *)(CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE);
struct mem_controller *ctrl = &( sysinfo->ctrl[node] );
for(j=0;j<DIMM_SOCKETS;j++) {
static u32 bios_reset_detected(void)
{
u32 htic;
- htic = pci_io_read_config32(PCI_DEV(CBB, CDB, 0), HT_INIT_CONTROL);
+ htic = pci_io_read_config32(PCI_DEV(CONFIG_CBB, CONFIG_CDB, 0), HT_INIT_CONTROL);
return (htic & HTIC_ColdR_Detect) && !(htic & HTIC_BIOSR_Detect);
}
static u32 cold_reset_detected(void)
{
u32 htic;
- htic = pci_io_read_config32(PCI_DEV(CBB, CDB, 0), HT_INIT_CONTROL);
+ htic = pci_io_read_config32(PCI_DEV(CONFIG_CBB, CONFIG_CDB, 0), HT_INIT_CONTROL);
return !(htic & HTIC_ColdR_Detect);
}
static u32 other_reset_detected(void) // other warm reset not started by BIOS
{
u32 htic;
- htic = pci_io_read_config32(PCI_DEV(CBB, CDB, 0), HT_INIT_CONTROL);
+ htic = pci_io_read_config32(PCI_DEV(CONFIG_CBB, CONFIG_CDB, 0), HT_INIT_CONTROL);
return (htic & HTIC_ColdR_Detect) && (htic & HTIC_BIOSR_Detect);
}
device_t dev;
int i;
- nodes = ((pci_read_config32(PCI_DEV(CBB, CDB, 0), 0x60) >> 4) & 7) + 1;
+ nodes = ((pci_read_config32(PCI_DEV(CONFIG_CBB, CONFIG_CDB, 0), 0x60) >> 4) & 7) + 1;
for(i = 0; i < nodes; i++) {
dev = NODE_PCI(i,0);
for(reg = 0xE0; reg < 0xF0; reg += 0x04) {
u32 config_map;
- config_map = pci_io_read_config32(PCI_DEV(CBB, CDB, 1), reg);
+ config_map = pci_io_read_config32(PCI_DEV(CONFIG_CBB, CONFIG_CDB, 1), reg);
if ((config_map & 3) != 3) {
continue;
}
}
}
-#if EXT_CONF_SUPPORT == 1
+#if CONFIG_EXT_CONF_SUPPORT == 1
// let's check that in extend space
// use the nodeid extend space to find out the bus for the linkn
u32 tempreg;
static u32 get_sblk(void)
{
u32 reg;
- /* read PCI_DEV(CBB,CDB,0) 0x64 bit [8:9] to find out SbLink m */
- reg = pci_io_read_config32(PCI_DEV(CBB, CDB, 0), 0x64);
+ /* read PCI_DEV(CONFIG_CBB,CONFIG_CDB,0) 0x64 bit [8:9] to find out SbLink m */
+ reg = pci_io_read_config32(PCI_DEV(CONFIG_CBB, CONFIG_CDB, 0), 0x64);
return ((reg>>8) & 3) ;
}
* This field defines the upper address bits of a 40 bit
* address that define the end of the DRAM region.
*/
- PCI_ADDR(CBB, CDB, 1, 0x44), 0x0000f8f8, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0x4C), 0x0000f8f8, 0x00000001,
- PCI_ADDR(CBB, CDB, 1, 0x54), 0x0000f8f8, 0x00000002,
- PCI_ADDR(CBB, CDB, 1, 0x5C), 0x0000f8f8, 0x00000003,
- PCI_ADDR(CBB, CDB, 1, 0x64), 0x0000f8f8, 0x00000004,
- PCI_ADDR(CBB, CDB, 1, 0x6C), 0x0000f8f8, 0x00000005,
- PCI_ADDR(CBB, CDB, 1, 0x74), 0x0000f8f8, 0x00000006,
- PCI_ADDR(CBB, CDB, 1, 0x7C), 0x0000f8f8, 0x00000007,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x44), 0x0000f8f8, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x4C), 0x0000f8f8, 0x00000001,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x54), 0x0000f8f8, 0x00000002,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x5C), 0x0000f8f8, 0x00000003,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x64), 0x0000f8f8, 0x00000004,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x6C), 0x0000f8f8, 0x00000005,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x74), 0x0000f8f8, 0x00000006,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x7C), 0x0000f8f8, 0x00000007,
/* DRAM Base i Registers
* F1:0x40 i = 0
* F1:0x48 i = 1
* This field defines the upper address bits of a 40-bit
* address that define the start of the DRAM region.
*/
- PCI_ADDR(CBB, CDB, 1, 0x40), 0x0000f8fc, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0x48), 0x0000f8fc, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0x50), 0x0000f8fc, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0x58), 0x0000f8fc, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0x60), 0x0000f8fc, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0x68), 0x0000f8fc, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0x70), 0x0000f8fc, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0x78), 0x0000f8fc, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x40), 0x0000f8fc, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x48), 0x0000f8fc, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x50), 0x0000f8fc, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x58), 0x0000f8fc, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x60), 0x0000f8fc, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x68), 0x0000f8fc, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x70), 0x0000f8fc, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x78), 0x0000f8fc, 0x00000000,
/* Memory-Mapped I/O Limit i Registers
* F1:0x84 i = 0
* address that defines the end of a memory-mapped
* I/O region n
*/
- PCI_ADDR(CBB, CDB, 1, 0x84), 0x00000048, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0x8C), 0x00000048, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0x94), 0x00000048, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0x9C), 0x00000048, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0xA4), 0x00000048, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0xAC), 0x00000048, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0xB4), 0x00000048, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0xBC), 0x00000048, 0x00ffff00,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x84), 0x00000048, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x8C), 0x00000048, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x94), 0x00000048, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x9C), 0x00000048, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xA4), 0x00000048, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xAC), 0x00000048, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xB4), 0x00000048, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xBC), 0x00000048, 0x00ffff00,
/* Memory-Mapped I/O Base i Registers
* F1:0x80 i = 0
* address that defines the start of memory-mapped
* I/O region i
*/
- PCI_ADDR(CBB, CDB, 1, 0x80), 0x000000f0, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0x88), 0x000000f0, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0x90), 0x000000f0, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0x98), 0x000000f0, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0xA0), 0x000000f0, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0xA8), 0x000000f0, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0xB0), 0x000000f0, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0xB8), 0x000000f0, 0x00fc0003,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x80), 0x000000f0, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x88), 0x000000f0, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x90), 0x000000f0, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x98), 0x000000f0, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xA0), 0x000000f0, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xA8), 0x000000f0, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xB0), 0x000000f0, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xB8), 0x000000f0, 0x00fc0003,
/* PCI I/O Limit i Registers
* F1:0xC4 i = 0
* This field defines the end of PCI I/O region n
* [31:25] Reserved
*/
- PCI_ADDR(CBB, CDB, 1, 0xC4), 0xFE000FC8, 0x01fff000,
- PCI_ADDR(CBB, CDB, 1, 0xCC), 0xFE000FC8, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0xD4), 0xFE000FC8, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0xDC), 0xFE000FC8, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xC4), 0xFE000FC8, 0x01fff000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xCC), 0xFE000FC8, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xD4), 0xFE000FC8, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xDC), 0xFE000FC8, 0x00000000,
/* PCI I/O Base i Registers
* F1:0xC0 i = 0
* This field defines the start of PCI I/O region n
* [31:25] Reserved
*/
- PCI_ADDR(CBB, CDB, 1, 0xC0), 0xFE000FCC, 0x00000003,
- PCI_ADDR(CBB, CDB, 1, 0xC8), 0xFE000FCC, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0xD0), 0xFE000FCC, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0xD8), 0xFE000FCC, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xC0), 0xFE000FCC, 0x00000003,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xC8), 0xFE000FCC, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xD0), 0xFE000FCC, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xD8), 0xFE000FCC, 0x00000000,
/* Config Base and Limit i Registers
* F1:0xE0 i = 0
* This field defines the highest bus number in
* configuration regin i
*/
- PCI_ADDR(CBB, CDB, 1, 0xE0), 0x0000FC88, 0xff000003,
- PCI_ADDR(CBB, CDB, 1, 0xE4), 0x0000FC88, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0xE8), 0x0000FC88, 0x00000000,
- PCI_ADDR(CBB, CDB, 1, 0xEC), 0x0000FC88, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xE0), 0x0000FC88, 0xff000003,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xE4), 0x0000FC88, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xE8), 0x0000FC88, 0x00000000,
+ PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xEC), 0x0000FC88, 0x00000000,
};
u32 max;
device_t dev;
u32 nodes;
- dev = PCI_DEV(CBB, CDB, 0);
+ dev = PCI_DEV(CONFIG_CBB, CONFIG_CDB, 0);
nodes = ((pci_read_config32(dev, 0x60)>>4) & 7) ;
#if CONFIG_MAX_PHYSICAL_CPUS > 8
nodes += (((pci_read_config32(dev, 0x160)>>4) & 7)<<3);
*/
BOOL AMD_CB_ManualBUIDSwapList (u8 node, u16 link, u8 **List)
{
- const u8 swaplist[] = { 0xFF, HT_CHAIN_UNITID_BASE, HT_CHAIN_END_UNITID_BASE, 0xFF };
+ const u8 swaplist[] = { 0xFF, CONFIG_HT_CHAIN_UNITID_BASE, CONFIG_HT_CHAIN_END_UNITID_BASE, 0xFF };
/* If the BUID was adjusted in early_ht we need to do the manual override */
- if ((HT_CHAIN_UNITID_BASE != 0) && (HT_CHAIN_END_UNITID_BASE != 0)) {
+ if ((CONFIG_HT_CHAIN_UNITID_BASE != 0) && (CONFIG_HT_CHAIN_END_UNITID_BASE != 0)) {
printk_debug("AMD_CB_ManualBUIDSwapList()\n");
if ((node == 0) && (link == 0)) { /* BSP SB link */
*List = swaplist;
-uses AGP_APERTURE_SIZE
-uses HAVE_ACPI_TABLES
-uses HAVE_HIGH_TABLES
-uses K8_REV_F_SUPPORT
+uses CONFIG_AGP_APERTURE_SIZE
+uses CONFIG_HAVE_ACPI_TABLES
+uses CONFIG_HAVE_HIGH_TABLES
+uses CONFIG_K8_REV_F_SUPPORT
-default AGP_APERTURE_SIZE=0x4000000
-default HAVE_HIGH_TABLES=1
+default CONFIG_AGP_APERTURE_SIZE=0x4000000
+default CONFIG_HAVE_HIGH_TABLES=1
config chip.h
driver northbridge.o
driver misc_control.o
-if K8_REV_F_SUPPORT
+if CONFIG_K8_REV_F_SUPPORT
makerule raminit_test
depends "$(TOP)/src/northbridge/amd/amdk8/raminit_test.c"
depends "$(TOP)/src/northbridge/amd/amdk8/raminit_f.c"
- action "$(HOSTCC) $(HOSTCFLAGS) $(CPUFLAGS) -Wno-unused-function -I$(TOP)/src/include -g $< -o $@"
+ action "$(CONFIG_HOSTCC) $(HOSTCFLAGS) $(CPUFLAGS) -Wno-unused-function -I$(TOP)/src/include -g $< -o $@"
end
else
makerule raminit_test
depends "$(TOP)/src/northbridge/amd/amdk8/raminit_test.c"
depends "$(TOP)/src/northbridge/amd/amdk8/raminit.c"
- action "$(HOSTCC) $(HOSTCFLAGS) $(CPUFLAGS) -Wno-unused-function -I$(TOP)/src/include -g $< -o $@"
+ action "$(CONFIG_HOSTCC) $(HOSTCFLAGS) $(CPUFLAGS) -Wno-unused-function -I$(TOP)/src/include -g $< -o $@"
end
end
-if HAVE_ACPI_TABLES
+if CONFIG_HAVE_ACPI_TABLES
object amdk8_acpi.o
end
#define AMDK8_H
-#if K8_REV_F_SUPPORT == 1
+#if CONFIG_K8_REV_F_SUPPORT == 1
#include "amdk8_f.h"
#else
#include "amdk8_pre_f.h"
#define TRY_HIGH_FIRST 0
#endif
-#ifndef K8_HT_FREQ_1G_SUPPORT
- #define K8_HT_FREQ_1G_SUPPORT 0
+#ifndef CONFIG_K8_HT_FREQ_1G_SUPPORT
+ #define CONFIG_K8_HT_FREQ_1G_SUPPORT 0
#endif
#ifndef K8_HT_CHECK_PENDING_LINK
#define CONFIG_MAX_PHYSICAL_CPUS_4_BUT_MORE_INSTALLED 0
#endif
-#ifndef ENABLE_APIC_EXT_ID
- #define ENABLE_APIC_EXT_ID 0
+#ifndef CONFIG_ENABLE_APIC_EXT_ID
+ #define CONFIG_ENABLE_APIC_EXT_ID 0
#endif
static void enable_apic_ext_id(u8 node)
{
-#if ENABLE_APIC_EXT_ID==1
+#if CONFIG_ENABLE_APIC_EXT_ID==1
#warning "FIXME Is the right place to enable apic ext id here?"
u32 val;
freq_cap = pci_read_config16(dev, pos);
freq_cap &= ~(1 << HT_FREQ_VENDOR); /* Ignore Vendor HT frequencies */
-#if K8_HT_FREQ_1G_SUPPORT == 1
- #if K8_REV_F_SUPPORT == 0
+#if CONFIG_K8_HT_FREQ_1G_SUPPORT == 1
+ #if CONFIG_K8_REV_F_SUPPORT == 0
if (!is_cpu_pre_e0())
#endif
{
static void coherent_ht_finalize(unsigned nodes)
{
unsigned node;
-#if K8_REV_F_SUPPORT == 0
+#if CONFIG_K8_REV_F_SUPPORT == 0
int rev_a0;
#endif
#if CONFIG_LOGICAL_CPUS==1
unsigned total_cpus;
- if ((!HAVE_OPTION_TABLE) ||
+ if ((!CONFIG_HAVE_OPTION_TABLE) ||
read_option(CMOS_VSTART_dual_core, CMOS_VLEN_dual_core, 0) == 0) { /* dual_core */
total_cpus = verify_dualcore(nodes);
}
*/
print_spew("coherent_ht_finalize\r\n");
-#if K8_REV_F_SUPPORT == 0
+#if CONFIG_K8_REV_F_SUPPORT == 0
rev_a0 = is_cpu_rev_a0();
#endif
for (node = 0; node < nodes; node++) {
(3 << HTTC_HI_PRI_BYP_CNT_SHIFT);
pci_write_config32(dev, HT_TRANSACTION_CONTROL, val);
-#if K8_REV_F_SUPPORT == 0
+#if CONFIG_K8_REV_F_SUPPORT == 0
if (rev_a0) {
pci_write_config32(dev, 0x94, 0);
pci_write_config32(dev, 0xb4, 0);
device_t dev;
uint32_t cmd;
dev = NODE_MC(node);
-#if K8_REV_F_SUPPORT == 0
+#if CONFIG_K8_REV_F_SUPPORT == 0
if (is_cpu_pre_c0()) {
/* Errata 66
print_debug("\r\n");
}
-#if K8_REV_F_SUPPORT == 1
+#if CONFIG_K8_REV_F_SUPPORT == 1
static uint32_t pci_read_config32_index_wait(device_t dev, uint32_t index_reg, uint32_t index);
static void dump_pci_device_index_wait(unsigned dev, uint32_t index_reg)
{
// only for sb ht chain
static void enumerate_ht_chain(void)
{
-#if HT_CHAIN_UNITID_BASE != 0
-/* HT_CHAIN_UNITID_BASE could be 0 (only one ht device in the ht chain), if so, don't need to go through the chain */
+#if CONFIG_HT_CHAIN_UNITID_BASE != 0
+/* CONFIG_HT_CHAIN_UNITID_BASE could be 0 (only one ht device in the ht chain), if so, don't need to go through the chain */
/* Assumption the HT chain that is bus 0 has the HT I/O Hub on it.
* On most boards this just happens. If a cpu has multiple
*/
unsigned next_unitid, last_unitid;
device_t dev;
-#if HT_CHAIN_END_UNITID_BASE != 0x20
- //let't record the device of last ht device, So we can set the Unitid to HT_CHAIN_END_UNITID_BASE
+#if CONFIG_HT_CHAIN_END_UNITID_BASE != 0x20
+ //let't record the device of last ht device, So we can set the Unitid to CONFIG_HT_CHAIN_END_UNITID_BASE
unsigned real_last_unitid;
uint8_t real_last_pos;
int ht_dev_num = 0; // except host_bridge
#endif
dev = PCI_DEV(0,0,0);
- next_unitid = HT_CHAIN_UNITID_BASE;
+ next_unitid = CONFIG_HT_CHAIN_UNITID_BASE;
do {
uint32_t id;
uint8_t hdr_type, pos;
unsigned ctrl, ctrl_off;
device_t devx;
-#if HT_CHAIN_END_UNITID_BASE != 0x20
+#if CONFIG_HT_CHAIN_END_UNITID_BASE != 0x20
if(next_unitid>=0x18) { // don't get mask out by k8, at this time BSP, RT is not enabled, it will response from 0x18,0--0x1f.
if(!end_used) {
- next_unitid = HT_CHAIN_END_UNITID_BASE;
+ next_unitid = CONFIG_HT_CHAIN_END_UNITID_BASE;
end_used = 1;
} else {
goto out;
out:
;
-#if HT_CHAIN_END_UNITID_BASE != 0x20
- if((ht_dev_num>1) && (real_last_unitid != HT_CHAIN_END_UNITID_BASE) && !end_used) {
+#if CONFIG_HT_CHAIN_END_UNITID_BASE != 0x20
+ if((ht_dev_num>1) && (real_last_unitid != CONFIG_HT_CHAIN_END_UNITID_BASE) && !end_used) {
uint16_t flags;
dev = PCI_DEV(0,real_last_unitid, 0);
flags = pci_read_config16(dev, real_last_pos + PCI_CAP_FLAGS);
flags &= ~0x1f;
- flags |= HT_CHAIN_END_UNITID_BASE & 0x1f;
+ flags |= CONFIG_HT_CHAIN_END_UNITID_BASE & 0x1f;
pci_write_config16(dev, real_last_pos + PCI_CAP_FLAGS, flags);
}
#endif
printk_debug(" done\n");
}
-#if HW_MEM_HOLE_SIZEK != 0
+#if CONFIG_HW_MEM_HOLE_SIZEK != 0
/* init hw mem hole here */
/* DramHoleValid bit only can be set after MemClrStatus is set by Hardware */
set_hw_mem_hole(controllers, ctrl);
* Just put all the possible HT Node/link to the list tp pci1234[] in
* src/mainboard/<vendor>/<mainboard>get_bus_conf.c
*
- * Also don't forget to increase the ACPI_SSDTX_NUM etc (FIXME what else) if
+ * Also don't forget to increase the CONFIG_ACPI_SSDTX_NUM etc (FIXME what else) if
* you have too many SSDTs
*
* What about co-processor in socket 1 on a 2 way system? Or socket 2 and
#include <device/pci_ids.h>
#include <device/hypertransport_def.h>
-#ifndef K8_HT_FREQ_1G_SUPPORT
- #define K8_HT_FREQ_1G_SUPPORT 0
+#ifndef CONFIG_K8_HT_FREQ_1G_SUPPORT
+ #define CONFIG_K8_HT_FREQ_1G_SUPPORT 0
#endif
#ifndef RAMINIT_SYSINFO
device_t dev;
//actually, only for one HT device HT chain, and unitid is 0
-#if HT_CHAIN_UNITID_BASE == 0
+#if CONFIG_HT_CHAIN_UNITID_BASE == 0
if(offset_unitid) {
return;
}
#endif
/* Check if is already collapsed */
- if((!offset_unitid) || (offset_unitid && (!((HT_CHAIN_END_UNITID_BASE == 0) && (HT_CHAIN_END_UNITID_BASE <HT_CHAIN_UNITID_BASE))))) {
+ if((!offset_unitid) || (offset_unitid && (!((CONFIG_HT_CHAIN_END_UNITID_BASE == 0) && (CONFIG_HT_CHAIN_END_UNITID_BASE <CONFIG_HT_CHAIN_UNITID_BASE))))) {
uint32_t id;
dev = PCI_DEV(bus, 0, 0);
id = pci_read_config32(dev, PCI_VENDOR_ID);
/* AMD K8 Unsupported 1Ghz? */
if (id == (PCI_VENDOR_ID_AMD | (0x1100 << 16))) {
- #if K8_HT_FREQ_1G_SUPPORT == 1
- #if K8_REV_F_SUPPORT == 0
+ #if CONFIG_K8_HT_FREQ_1G_SUPPORT == 1
+ #if CONFIG_K8_REV_F_SUPPORT == 0
if (is_cpu_pre_e0()) { // only E0 later support 1GHz
freq_cap &= ~(1 << HT_FREQ_1000Mhz);
}
return needs_reset;
}
-#if (USE_DCACHE_RAM == 1) && (K8_SCAN_PCI_BUS == 1)
+#if (CONFIG_USE_DCACHE_RAM == 1) && (K8_SCAN_PCI_BUS == 1)
#if RAMINIT_SYSINFO == 1
static void ht_setup_chainx(device_t udev, uint8_t upos, uint8_t bus, unsigned offset_unitid, struct sys_info *sysinfo);
static int ht_setup_chainx(device_t udev, uint8_t upos, uint8_t bus, unsigned offset_unitid)
#endif
{
- //even HT_CHAIN_UNITID_BASE == 0, we still can go through this function, because of end_of_chain check, also We need it to optimize link
+ //even CONFIG_HT_CHAIN_UNITID_BASE == 0, we still can go through this function, because of end_of_chain check, also We need it to optimize link
uint8_t next_unitid, last_unitid;
unsigned uoffs;
int reset_needed = 0;
#endif
-#if HT_CHAIN_END_UNITID_BASE != 0x20
- //let't record the device of last ht device, So we can set the Unitid to HT_CHAIN_END_UNITID_BASE
+#if CONFIG_HT_CHAIN_END_UNITID_BASE != 0x20
+ //let't record the device of last ht device, So we can set the Unitid to CONFIG_HT_CHAIN_END_UNITID_BASE
unsigned real_last_unitid;
uint8_t real_last_pos;
int ht_dev_num = 0;
#endif
uoffs = PCI_HT_HOST_OFFS;
- next_unitid = (offset_unitid) ? HT_CHAIN_UNITID_BASE:1;
+ next_unitid = (offset_unitid) ? CONFIG_HT_CHAIN_UNITID_BASE:1;
do {
uint32_t id;
}
-#if HT_CHAIN_END_UNITID_BASE != 0x20
+#if CONFIG_HT_CHAIN_END_UNITID_BASE != 0x20
if(offset_unitid) {
if(next_unitid>= (bus ? 0x20:0x18) ) {
if(!end_used) {
- next_unitid = HT_CHAIN_END_UNITID_BASE;
+ next_unitid = CONFIG_HT_CHAIN_END_UNITID_BASE;
end_used = 1;
} else {
goto out;
} while (last_unitid != next_unitid );
-#if HT_CHAIN_END_UNITID_BASE != 0x20
+#if CONFIG_HT_CHAIN_END_UNITID_BASE != 0x20
out:
#endif
end_of_chain: ;
-#if HT_CHAIN_END_UNITID_BASE != 0x20
- if(offset_unitid && (ht_dev_num>1) && (real_last_unitid != HT_CHAIN_END_UNITID_BASE) && !end_used ) {
+#if CONFIG_HT_CHAIN_END_UNITID_BASE != 0x20
+ if(offset_unitid && (ht_dev_num>1) && (real_last_unitid != CONFIG_HT_CHAIN_END_UNITID_BASE) && !end_used ) {
uint16_t flags;
int i;
flags = pci_read_config16(PCI_DEV(bus,real_last_unitid,0), real_last_pos + PCI_CAP_FLAGS);
flags &= ~0x1f;
- flags |= HT_CHAIN_END_UNITID_BASE & 0x1f;
+ flags |= CONFIG_HT_CHAIN_END_UNITID_BASE & 0x1f;
pci_write_config16(PCI_DEV(bus, real_last_unitid, 0), real_last_pos + PCI_CAP_FLAGS, flags);
#if RAMINIT_SYSINFO == 1
{
struct link_pair_st *link_pair = &sysinfo->link_pair[i];
if(link_pair->udev == PCI_DEV(bus, real_last_unitid, 0)) {
- link_pair->udev = PCI_DEV(bus, HT_CHAIN_END_UNITID_BASE, 0);
+ link_pair->udev = PCI_DEV(bus, CONFIG_HT_CHAIN_END_UNITID_BASE, 0);
continue;
}
if(link_pair->dev == PCI_DEV(bus, real_last_unitid, 0)) {
- link_pair->dev = PCI_DEV(bus, HT_CHAIN_END_UNITID_BASE, 0);
+ link_pair->dev = PCI_DEV(bus, CONFIG_HT_CHAIN_END_UNITID_BASE, 0);
}
}
#endif
#endif
{
unsigned offset_unitid = 0;
-#if ((HT_CHAIN_UNITID_BASE != 1) || (HT_CHAIN_END_UNITID_BASE != 0x20))
+#if ((CONFIG_HT_CHAIN_UNITID_BASE != 1) || (CONFIG_HT_CHAIN_END_UNITID_BASE != 0x20))
offset_unitid = 1;
#endif
/* Make certain the HT bus is not enumerated */
ht_collapse_previous_enumeration(0, 0);
-#if ((HT_CHAIN_UNITID_BASE != 1) || (HT_CHAIN_END_UNITID_BASE != 0x20))
+#if ((CONFIG_HT_CHAIN_UNITID_BASE != 1) || (CONFIG_HT_CHAIN_END_UNITID_BASE != 0x20))
offset_unitid = 1;
#endif
uint8_t val;
unsigned devn = 1;
- #if ((HT_CHAIN_UNITID_BASE != 1) || (HT_CHAIN_END_UNITID_BASE != 0x20))
- #if SB_HT_CHAIN_UNITID_OFFSET_ONLY == 1
+ #if ((CONFIG_HT_CHAIN_UNITID_BASE != 1) || (CONFIG_HT_CHAIN_END_UNITID_BASE != 0x20))
+ #if CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY == 1
if(i==0) // to check if it is sb ht chain
#endif
- devn = HT_CHAIN_UNITID_BASE;
+ devn = CONFIG_HT_CHAIN_UNITID_BASE;
#endif
reg = pci_read_config32(PCI_DEV(0,0x18,1), 0xe0 + i * 4);
unsigned regpos;
uint32_t dword;
uint8_t busn;
- #if (USE_DCACHE_RAM == 1) && (K8_SCAN_PCI_BUS == 1)
+ #if (CONFIG_USE_DCACHE_RAM == 1) && (K8_SCAN_PCI_BUS == 1)
unsigned bus;
#endif
unsigned offset_unitid = 0;
pci_write_config32( PCI_DEV(0, devpos,0), regpos , dword);
- #if ((HT_CHAIN_UNITID_BASE != 1) || (HT_CHAIN_END_UNITID_BASE != 0x20))
- #if SB_HT_CHAIN_UNITID_OFFSET_ONLY == 1
+ #if ((CONFIG_HT_CHAIN_UNITID_BASE != 1) || (CONFIG_HT_CHAIN_END_UNITID_BASE != 0x20))
+ #if CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY == 1
if(i==0) // to check if it is sb ht chain
#endif
offset_unitid = 1;
reset_needed |= ht_setup_chainx(udev,upos,busn, offset_unitid); //all not
#endif
- #if (USE_DCACHE_RAM == 1) && (K8_SCAN_PCI_BUS == 1)
+ #if (CONFIG_USE_DCACHE_RAM == 1) && (K8_SCAN_PCI_BUS == 1)
/* You can use use this in romcc, because there is function call in romcc, recursive will kill you */
bus = busn; // we need 32 bit
#if RAMINIT_SYSINFO == 1
if (iommu) {
/* Add a Gart apeture resource */
resource = new_resource(dev, 0x94);
- resource->size = iommu?AGP_APERTURE_SIZE:1;
+ resource->size = iommu?CONFIG_AGP_APERTURE_SIZE:1;
resource->align = log2(resource->size);
resource->gran = log2(resource->size);
resource->limit = 0xffffffff; /* 4G */
cmd = pci_read_config32(dev, 0x44);
cmd |= (1<<6) | (1<<25);
pci_write_config32(dev, 0x44, cmd );
-#if K8_REV_F_SUPPORT == 0
+#if CONFIG_K8_REV_F_SUPPORT == 0
if (is_cpu_pre_c0()) {
/* Errata 58
* We have no idea how many busses are behind this bridge yet,
* so we set the subordinate bus number to 0xff for the moment.
*/
-#if SB_HT_CHAIN_ON_BUS0 > 0
+#if CONFIG_SB_HT_CHAIN_ON_BUS0 > 0
// first chain will on bus 0
if((nodeid == 0) && (sblink==link)) { // actually max is 0 here
min_bus = max;
}
- #if SB_HT_CHAIN_ON_BUS0 > 1
+ #if CONFIG_SB_HT_CHAIN_ON_BUS0 > 1
// second chain will be on 0x40, third 0x80, forth 0xc0
else {
min_bus = ((max>>6) + 1) * 0x40;
if(nodeid==0) {
sblink = (pci_read_config32(dev, 0x64)>>8) & 3;
-#if SB_HT_CHAIN_ON_BUS0 > 0
- #if ((HT_CHAIN_UNITID_BASE != 1) || (HT_CHAIN_END_UNITID_BASE != 0x20))
+#if CONFIG_SB_HT_CHAIN_ON_BUS0 > 0
+ #if ((CONFIG_HT_CHAIN_UNITID_BASE != 1) || (CONFIG_HT_CHAIN_END_UNITID_BASE != 0x20))
offset_unitid = 1;
#endif
max = amdk8_scan_chain(dev, nodeid, sblink, sblink, max, offset_unitid ); // do sb ht chain at first, in case s2885 put sb chain (8131/8111) on link2, but put 8151 on link0
}
for(link = 0; link < dev->links; link++) {
-#if SB_HT_CHAIN_ON_BUS0 > 0
+#if CONFIG_SB_HT_CHAIN_ON_BUS0 > 0
if( (nodeid == 0) && (sblink == link) ) continue; //already done
#endif
offset_unitid = 0;
- #if ((HT_CHAIN_UNITID_BASE != 1) || (HT_CHAIN_END_UNITID_BASE != 0x20))
- #if SB_HT_CHAIN_UNITID_OFFSET_ONLY == 1
+ #if ((CONFIG_HT_CHAIN_UNITID_BASE != 1) || (CONFIG_HT_CHAIN_END_UNITID_BASE != 0x20))
+ #if CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY == 1
if((nodeid == 0) && (sblink == link))
#endif
offset_unitid = 1;
#define BRIDGE_IO_MASK (IORESOURCE_IO | IORESOURCE_MEM | IORESOURCE_PREFETCH)
#endif
-#if HW_MEM_HOLE_SIZEK != 0
+#if CONFIG_HW_MEM_HOLE_SIZEK != 0
struct hw_mem_hole_info {
unsigned hole_startk;
struct hw_mem_hole_info mem_hole;
int i;
- mem_hole.hole_startk = HW_MEM_HOLE_SIZEK;
+ mem_hole.hole_startk = CONFIG_HW_MEM_HOLE_SIZEK;
mem_hole.node_id = -1;
for (i = 0; i < FX_DEVS; i++) {
}
#endif
-#if HAVE_HIGH_TABLES==1
+#if CONFIG_HAVE_HIGH_TABLES==1
#define HIGH_TABLES_SIZE 64 // maximum size of high tables in KB
extern uint64_t high_tables_base, high_tables_size;
#endif
unsigned long mmio_basek;
uint32_t pci_tolm;
int i, idx;
-#if HW_MEM_HOLE_SIZEK != 0
+#if CONFIG_HW_MEM_HOLE_SIZEK != 0
struct hw_mem_hole_info mem_hole;
unsigned reset_memhole = 1;
#endif
mmio_basek &= ~((64*1024) - 1);
#endif
-#if HW_MEM_HOLE_SIZEK != 0
+#if CONFIG_HW_MEM_HOLE_SIZEK != 0
/* if the hw mem hole is already set in raminit stage, here we will compare mmio_basek and hole_basek
* if mmio_basek is bigger that hole_basek and will use hole_basek as mmio_basek and we don't need to reset hole.
* otherwise We reset the hole to the mmio_basek
*/
- #if K8_REV_F_SUPPORT == 0
+ #if CONFIG_K8_REV_F_SUPPORT == 0
if (!is_cpu_pre_e0()) {
#endif
//mmio_basek = 3*1024*1024; // for debug to meet boundary
if(reset_memhole) {
- if(mem_hole.node_id!=-1) { // We need to select HW_MEM_HOLE_SIZEK for raminit, it can not make hole_startk to some basek too....!
+ if(mem_hole.node_id!=-1) { // We need to select CONFIG_HW_MEM_HOLE_SIZEK for raminit, it can not make hole_startk to some basek too....!
// We need to reset our Mem Hole, because We want more big HOLE than we already set
//Before that We need to disable mem hole at first, becase memhole could already be set on i+1 instead
disable_hoist_memory(mem_hole.hole_startk, mem_hole.node_id);
}
- #if HW_MEM_HOLE_SIZE_AUTO_INC == 1
+ #if CONFIG_HW_MEM_HOLE_SIZE_AUTO_INC == 1
//We need to double check if the mmio_basek is valid for hole setting, if it is equal to basek, we need to decrease it some
uint32_t basek_pri;
for (i = 0; i < FX_DEVS; i++) {
#endif
}
-#if K8_REV_F_SUPPORT == 0
+#if CONFIG_K8_REV_F_SUPPORT == 0
} // is_cpu_pre_e0
#endif
ram_resource(dev, (idx | i), basek, pre_sizek);
idx += 0x10;
sizek -= pre_sizek;
-#if HAVE_HIGH_TABLES==1
+#if CONFIG_HAVE_HIGH_TABLES==1
if (i==0 && high_tables_base==0) {
/* Leave some space for ACPI, PIRQ and MP tables */
high_tables_base = (mmio_basek - HIGH_TABLES_SIZE) * 1024;
}
#endif
}
- #if HW_MEM_HOLE_SIZEK != 0
+ #if CONFIG_HW_MEM_HOLE_SIZEK != 0
if(reset_memhole)
- #if K8_REV_F_SUPPORT == 0
+ #if CONFIG_K8_REV_F_SUPPORT == 0
if(!is_cpu_pre_e0() )
#endif
sizek += hoist_memory(mmio_basek,i);
if (sizek)
ram_resource(dev, (idx | i), basek, sizek);
idx += 0x10;
-#if HAVE_HIGH_TABLES==1
+#if CONFIG_HAVE_HIGH_TABLES==1
printk_debug("%d: mmio_basek=%08lx, basek=%08x, limitk=%08x\n",
i, mmio_basek, basek, limitk);
if (i==0 && high_tables_base==0) {
sysconf.enabled_apic_ext_id = 1;
if(bsp_apicid == 0) {
/* bsp apic id is not changed */
- sysconf.apicid_offset = APIC_ID_OFFSET;
+ sysconf.apicid_offset = CONFIG_APIC_ID_OFFSET;
} else
{
sysconf.lift_bsp_apicid = 1;
// That is the typical case
if(j == 0 ){
- #if K8_REV_F_SUPPORT == 0
+ #if CONFIG_K8_REV_F_SUPPORT == 0
e0_later_single_core = is_e0_later_in_bsp(i); // single core
#else
e0_later_single_core = is_cpu_f0_in_bsp(i); // We can read cpuid(1) from Func3
if (nbcap & NBCAP_ECC) {
dcl |= DCL_DimmEccEn;
}
- if (HAVE_OPTION_TABLE &&
+ if (CONFIG_HAVE_OPTION_TABLE &&
read_option(CMOS_VSTART_ECC_memory, CMOS_VLEN_ECC_memory, 1) == 0) {
dcl &= ~DCL_DimmEccEn;
}
* so I can see my rom chip and other I/O devices.
*/
if (tom_k >= 0x003f0000) {
-#if HW_MEM_HOLE_SIZEK != 0
+#if CONFIG_HW_MEM_HOLE_SIZEK != 0
if (hole_startk != 0) {
tom_k = hole_startk;
} else
{
unsigned long tom_k, base_k;
- if ((!HAVE_OPTION_TABLE) ||
+ if ((!CONFIG_HAVE_OPTION_TABLE) ||
read_option(CMOS_VSTART_interleave_chip_selects, CMOS_VLEN_interleave_chip_selects, 1) != 0) {
tom_k = interleave_chip_selects(ctrl);
} else {
min_cycle_time = min_cycle_times[(value >> NBCAP_MEMCLK_SHIFT) & NBCAP_MEMCLK_MASK];
bios_cycle_time = min_cycle_times[
read_option(CMOS_VSTART_max_mem_clock, CMOS_VLEN_max_mem_clock, 0)];
- if (HAVE_OPTION_TABLE && bios_cycle_time > min_cycle_time) {
+ if (CONFIG_HAVE_OPTION_TABLE && bios_cycle_time > min_cycle_time) {
min_cycle_time = bios_cycle_time;
}
min_latency = 2;
return;
}
-#if HW_MEM_HOLE_SIZEK != 0
+#if CONFIG_HW_MEM_HOLE_SIZEK != 0
static uint32_t hoist_memory(int controllers, const struct mem_controller *ctrl,unsigned hole_startk, int i)
{
int ii;
uint32_t hole_startk;
int i;
- hole_startk = 4*1024*1024 - HW_MEM_HOLE_SIZEK;
+ hole_startk = 4*1024*1024 - CONFIG_HW_MEM_HOLE_SIZEK;
printk_spew("Handling memory hole at 0x%08x (default)\n", hole_startk);
-#if HW_MEM_HOLE_SIZE_AUTO_INC == 1
+#if CONFIG_HW_MEM_HOLE_SIZE_AUTO_INC == 1
/* We need to double check if hole_startk is valid.
* If it is equal to the dram base address in K (base_k),
* we need to decrease it.
printk_debug(" done\n");
}
-#if HW_MEM_HOLE_SIZEK != 0
+#if CONFIG_HW_MEM_HOLE_SIZEK != 0
// init hw mem hole here
/* DramHoleValid bit only can be set after MemClrStatus is set by Hardware */
if (!is_cpu_pre_e0())
if (base0) {
uint32_t dword;
uint32_t ClkDis0;
-#if CPU_SOCKET_TYPE == 0x10 /* L1 */
+#if CONFIG_CPU_SOCKET_TYPE == 0x10 /* L1 */
ClkDis0 = DTL_MemClkDis0;
-#elif CPU_SOCKET_TYPE == 0x11 /* AM2 */
+#elif CONFIG_CPU_SOCKET_TYPE == 0x11 /* AM2 */
ClkDis0 = DTL_MemClkDis0_AM2;
-#elif CPU_SOCKET_TYPE == 0x12 /* S1G1 */
+#elif CONFIG_CPU_SOCKET_TYPE == 0x12 /* S1G1 */
ClkDis0 = DTL_MemClkDis0_S1g1;
#endif
* so I can see my rom chip and other I/O devices.
*/
if (tom_k >= 0x003f0000) {
-#if HW_MEM_HOLE_SIZEK != 0
+#if CONFIG_HW_MEM_HOLE_SIZEK != 0
if (hole_startk != 0) {
tom_k = hole_startk;
} else
u8 common_cl;
/* S1G1 and AM2 sockets are Mod64BitMux capable. */
-#if CPU_SOCKET_TYPE == 0x11 || CPU_SOCKET_TYPE == 0x12
+#if CONFIG_CPU_SOCKET_TYPE == 0x11 || CONFIG_CPU_SOCKET_TYPE == 0x12
u8 mux_cap = 1;
#else
u8 mux_cap = 0;
}
-#if DIMM_SUPPORT == 0x0204
+#if CONFIG_DIMM_SUPPORT == 0x0204
odt = 0x2; /* 150 ohms */
#endif
long dimm_mask = meminfo->dimm_mask & 0x0f;
-#if DIMM_SUPPORT==0x0104 /* DDR2 and REG */
+#if CONFIG_DIMM_SUPPORT==0x0104 /* DDR2 and REG */
/* for REG DIMM */
dword = 0x00111222;
dwordx = 0x002f0000;
#endif
-#if DIMM_SUPPORT==0x0204 /* DDR2 and SO-DIMM, S1G1 */
+#if CONFIG_DIMM_SUPPORT==0x0204 /* DDR2 and SO-DIMM, S1G1 */
dword = 0x00111222;
dwordx = 0x002F2F00;
}
#endif
-#if DIMM_SUPPORT==0x0004 /* DDR2 and unbuffered */
+#if CONFIG_DIMM_SUPPORT==0x0004 /* DDR2 and unbuffered */
/* for UNBUF DIMM */
dword = 0x00111222;
dwordx = 0x002f2f00;
printk_raminit("\tAddr Timing= %08x\n", dwordx);
#endif
-#if (DIMM_SUPPORT & 0x0100)==0x0000 /* 2T mode only used for unbuffered DIMM */
+#if (CONFIG_DIMM_SUPPORT & 0x0100)==0x0000 /* 2T mode only used for unbuffered DIMM */
if (SlowAccessMode) {
set_SlowAccessMode(ctrl);
}
static void set_RDqsEn(const struct mem_controller *ctrl,
const struct mem_param *param, struct mem_info *meminfo)
{
-#if CPU_SOCKET_TYPE==0x10
+#if CONFIG_CPU_SOCKET_TYPE==0x10
//only need to set for reg and x8
uint32_t dch;
#include "raminit_f_dqs.c"
-#if HW_MEM_HOLE_SIZEK != 0
+#if CONFIG_HW_MEM_HOLE_SIZEK != 0
static uint32_t hoist_memory(int controllers, const struct mem_controller *ctrl,unsigned hole_startk, int i)
{
int ii;
uint32_t hole_startk;
int i;
- hole_startk = 4*1024*1024 - HW_MEM_HOLE_SIZEK;
+ hole_startk = 4*1024*1024 - CONFIG_HW_MEM_HOLE_SIZEK;
printk_raminit("Handling memory hole at 0x%08x (default)\n", hole_startk);
-#if HW_MEM_HOLE_SIZE_AUTO_INC == 1
+#if CONFIG_HW_MEM_HOLE_SIZE_AUTO_INC == 1
/* We need to double check if the hole_startk is valid, if it is equal
to basek, we need to decrease it some */
uint32_t basek_pri;
printk_debug(" done\n");
}
-#if HW_MEM_HOLE_SIZEK != 0
+#if CONFIG_HW_MEM_HOLE_SIZEK != 0
/* init hw mem hole here */
/* DramHoleValid bit only can be set after MemClrStatus is set by Hardware */
set_hw_mem_hole(controllers, ctrl);
}
-#if MEM_TRAIN_SEQ == 0
+#if CONFIG_MEM_TRAIN_SEQ == 0
#if K8_REV_F_SUPPORT_F0_F1_WORKAROUND == 1
dqs_timing(controllers, ctrl, tsc0, sysinfo);
#else
#endif
#else
-#if MEM_TRAIN_SEQ == 2
+#if CONFIG_MEM_TRAIN_SEQ == 2
/* need to enable mtrr, so dqs training could access the test address */
setup_mtrr_dqs(sysinfo->tom_k, sysinfo->tom2_k);
#endif
dqs_timing(i, &ctrl[i], sysinfo, 1);
-#if MEM_TRAIN_SEQ == 1
+#if CONFIG_MEM_TRAIN_SEQ == 1
break; // only train the first node with ram
#endif
}
-#if MEM_TRAIN_SEQ == 2
+#if CONFIG_MEM_TRAIN_SEQ == 2
clear_mtrr_dqs(sysinfo->tom2_k);
#endif
#endif
-#if MEM_TRAIN_SEQ != 1
+#if CONFIG_MEM_TRAIN_SEQ != 1
wait_all_core0_mem_trained(sysinfo);
#endif
uint32_t mem_base;
unsigned nodeid = ctrl->node_id;
-#if HW_MEM_HOLE_SIZEK != 0
+#if CONFIG_HW_MEM_HOLE_SIZEK != 0
uint32_t hole_reg;
#endif
mem_base &= 0xffff0000;
dword += mem_base;
-#if HW_MEM_HOLE_SIZEK != 0
+#if CONFIG_HW_MEM_HOLE_SIZEK != 0
hole_reg = sysinfo->hole_reg[nodeid];
if(hole_reg & 1) {
unsigned hole_startk;
//restore SSE2 setting
disable_sse2();
-#if MEM_TRAIN_SEQ != 1
+#if CONFIG_MEM_TRAIN_SEQ != 1
/* We need tidy output for type 1 */
printk_debug(" CTLRMaxDelay=%02x\n", CTLRMaxDelay);
#endif
align = max_align;
}
sizek = 1 << align;
-#if MEM_TRAIN_SEQ != 1
+#if CONFIG_MEM_TRAIN_SEQ != 1
printk_debug("Setting variable MTRR %d, base: %4dMB, range: %4dMB, type %s\r\n",
reg, range_startk >>10, sizek >> 10,
(type==MTRR_TYPE_UNCACHEABLE)?"UC":
pci_write_config32(dev, DRAM_CONFIG_HIGH, reg);
}
-#if MEM_TRAIN_SEQ == 0
+#if CONFIG_MEM_TRAIN_SEQ == 0
#if K8_REV_F_SUPPORT_F0_F1_WORKAROUND == 1
static void dqs_timing(int controllers, const struct mem_controller *ctrl, tsc_t *tsc0, struct sys_info *sysinfo)
#else
#endif
-#if MEM_TRAIN_SEQ > 0
+#if CONFIG_MEM_TRAIN_SEQ > 0
static void dqs_timing(int i, const struct mem_controller *ctrl, struct sys_info *sysinfo, unsigned v)
{
if(sysinfo->mem_trained[i] != 0x80) return;
-#if MEM_TRAIN_SEQ == 1
+#if CONFIG_MEM_TRAIN_SEQ == 1
//need to enable mtrr, so dqs training could access the test address
setup_mtrr_dqs(sysinfo->tom_k, sysinfo->tom2_k);
#endif
}
out:
-#if MEM_TRAIN_SEQ == 1
+#if CONFIG_MEM_TRAIN_SEQ == 1
clear_mtrr_dqs(sysinfo->tom2_k);
#endif
}
#endif
-#if MEM_TRAIN_SEQ == 1
+#if CONFIG_MEM_TRAIN_SEQ == 1
static void train_ram(unsigned nodeid, struct sys_info *sysinfo, struct sys_info *sysinfox)
{
dqs_timing(nodeid, &sysinfo->ctrl[nodeid], sysinfo, 0); // keep the output tidy
static inline void train_ram_on_node(unsigned nodeid, unsigned coreid, struct sys_info *sysinfo, unsigned retcall)
{
if(coreid) return; // only do it on core0
- struct sys_info *sysinfox = ((CONFIG_LB_MEM_TOPK<<10) - DCACHE_RAM_GLOBAL_VAR_SIZE);
+ struct sys_info *sysinfox = ((CONFIG_LB_MEM_TOPK<<10) - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE);
wait_till_sysinfo_in_ram(); // use pci to get it
if(sysinfox->mem_trained[nodeid] == 0x80) {
sysinfo->mem_trained[nodeid] = sysinfox->mem_trained[nodeid];
memcpy(&sysinfo->ctrl[nodeid], &sysinfox->ctrl[nodeid], sizeof(struct mem_controller));
#else
- memcpy(sysinfo, sysinfox, DCACHE_RAM_GLOBAL_VAR_SIZE);
+ memcpy(sysinfo, sysinfox, CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE);
#endif
set_top_mem_ap(sysinfo->tom_k, sysinfo->tom2_k); // keep the ap's tom consistent with bsp's
#if CONFIG_AP_CODE_IN_CAR == 0
-uses HAVE_HIGH_TABLES
+uses CONFIG_HAVE_HIGH_TABLES
config chip.h
driver northbridge.o
-default HAVE_HIGH_TABLES=1
+default CONFIG_HAVE_HIGH_TABLES=1
return tolm;
}
-#if HAVE_HIGH_TABLES==1
+#if CONFIG_HAVE_HIGH_TABLES==1
#define HIGH_TABLES_SIZE 64 // maximum size of high tables in KB
extern uint64_t high_tables_base, high_tables_size;
#endif
tolmk = tomk;
}
-#if HAVE_HIGH_TABLES==1
+#if CONFIG_HAVE_HIGH_TABLES==1
/* Leave some space for ACPI, PIRQ and MP tables */
high_tables_base = (tolmk - HIGH_TABLES_SIZE) * 1024;
high_tables_size = HIGH_TABLES_SIZE * 1024;
-uses HAVE_HIGH_TABLES
+uses CONFIG_HAVE_HIGH_TABLES
config chip.h
driver northbridge.o
object northbridgeinit.o
object chipsetinit.o
object grphinit.o
-default HAVE_HIGH_TABLES=1
+default CONFIG_HAVE_HIGH_TABLES=1
void chipsetInit (void);
-#if HAVE_HIGH_TABLES==1
+#if CONFIG_HAVE_HIGH_TABLES==1
#define HIGH_TABLES_SIZE 64 // maximum size of high tables in KB
extern uint64_t high_tables_base, high_tables_size;
#endif
dev->ops = &pci_domain_ops;
pci_set_method(dev);
tomk = ((sizeram() - VIDEO_MB) * 1024) - SMM_SIZE;
-#if HAVE_HIGH_TABLES==1
+#if CONFIG_HAVE_HIGH_TABLES==1
/* Leave some space for ACPI, PIRQ and MP tables */
high_tables_base = (tomk - HIGH_TABLES_SIZE) * 1024;
high_tables_size = HIGH_TABLES_SIZE * 1024;
-uses HAVE_HIGH_TABLES
+uses CONFIG_HAVE_HIGH_TABLES
config chip.h
driver northbridge.o
object northbridgeinit.o
object grphinit.o
-default HAVE_HIGH_TABLES=1
+default CONFIG_HAVE_HIGH_TABLES=1
*/
void print_conf(void)
{
-#if DEFAULT_CONSOLE_LOGLEVEL >= BIOS_ERR
+#if CONFIG_DEFAULT_CONSOLE_LOGLEVEL >= BIOS_ERR
int i;
unsigned long iol;
msr_t msr;
iol = inl(GPIO_MAPPER_X);
printk_debug("IOR 0x%08X is now 0x%08X\n", GPIO_IO_BASE + GPIO_MAPPER_X,
iol);
-#endif //DEFAULT_CONSOLE_LOGLEVEL >= BIOS_ERR
+#endif //CONFIG_DEFAULT_CONSOLE_LOGLEVEL >= BIOS_ERR
}
/* todo: add a resource record. We don't do this here because this may be called when
IORESOURCE_FIXED | IORESOURCE_STORED | IORESOURCE_ASSIGNED;
}
-#if HAVE_HIGH_TABLES==1
+#if CONFIG_HAVE_HIGH_TABLES==1
#define HIGH_TABLES_SIZE 64 // maximum size of high tables in KB
extern uint64_t high_tables_base, high_tables_size;
#endif
ram_resource(dev, idx++, 0, 640);
ram_resource(dev, idx++, 1024, tomk - 1024); // Systop - 1 MB -> KB
-#if HAVE_HIGH_TABLES==1
+#if CONFIG_HAVE_HIGH_TABLES==1
/* Leave some space for ACPI, PIRQ and MP tables */
high_tables_base = (tomk - HIGH_TABLES_SIZE) * 1024;
high_tables_size = HIGH_TABLES_SIZE * 1024;
setCPC710_PCI32(CPC710_PCIL0_MSIZE, CPC710_PCI32_MEM_SIZE);
setCPC710_PCI32(CPC710_PCIL0_IOSIZE, CPC710_PCI32_IO_SIZE);
setCPC710_PCI32(CPC710_PCIL0_SMBAR, CPC710_PCI32_MEM_BASE);
- setCPC710_PCI32(CPC710_PCIL0_SIBAR, CPC710_PCI32_IO_BASE);
+ setCPC710_PCI32(CPC710_PCIL0_SIBAR, CPC710_PCI32CONFIG_IO_BASE);
setCPC710_PCI32(CPC710_PCIL0_CTLRW, 0x00000000);
setCPC710_PCI32(CPC710_PCIL0_PSSIZE, 0x00000080);
setCPC710_PCI32(CPC710_PCIL0_BARPS, 0x00000000);
setCPC710_PCI64(CPC710_PCIL0_MSIZE, CPC710_PCI64_MEM_SIZE);
setCPC710_PCI64(CPC710_PCIL0_IOSIZE, CPC710_PCI64_IO_SIZE);
setCPC710_PCI64(CPC710_PCIL0_SMBAR, CPC710_PCI64_MEM_BASE);
- setCPC710_PCI64(CPC710_PCIL0_SIBAR, CPC710_PCI64_IO_BASE);
+ setCPC710_PCI64(CPC710_PCIL0_SIBAR, CPC710_PCI64CONFIG_IO_BASE);
setCPC710_PCI64(CPC710_PCIL0_CTLRW, 0x02000000);
setCPC710_PCI64(CPC710_PCIL0_PSSIZE, 0x00000080);
#ifndef _CPC710_PCI_H_
#define _CPC710_PCI_H_
-#define CPC710_PCI32_CONFIG (PCIC0_CFGADDR & 0xfff00000)
+#define CPC710_PCI32_CONFIG (CONFIG_PCIC0_CFGADDR & 0xfff00000)
#define CPC710_PCI32_MEM_SIZE 0xf8000000
#define CPC710_PCI32_MEM_BASE 0xc0000000
#define CPC710_PCI32_IO_SIZE 0xf8000000
-#define CPC710_PCI32_IO_BASE 0x80000000
+#define CPC710_PCI32CONFIG_IO_BASE 0x80000000
//#define CPC710_PCI64_CONFIG 0xff400000
//#define CPC710_PCI64_MEM_SIZE 0xf8000000
//#define CPC710_PCI64_MEM_BASE 0xc8000000
//#define CPC710_PCI64_IO_SIZE 0xf8000000
-//#define CPC710_PCI64_IO_BASE 0x88000000
+//#define CPC710_PCI64CONFIG_IO_BASE 0x88000000
#define CPC710_PCIL0_PSEA 0xf6110
#define CPC710_PCIL0_PCIDG 0xf6120
-uses HAVE_HIGH_TABLES
+uses CONFIG_HAVE_HIGH_TABLES
config chip.h
object northbridge.o
-default HAVE_HIGH_TABLES=1
+default CONFIG_HAVE_HIGH_TABLES=1
return tolm;
}
-#if HAVE_HIGH_TABLES==1
+#if CONFIG_HAVE_HIGH_TABLES==1
#define HIGH_TABLES_SIZE 64 // maximum size of high tables in KB
extern uint64_t high_tables_base, high_tables_size;
#endif
(remaplimitk + 64*1024) - remapbasek);
}
-#if HAVE_HIGH_TABLES==1
+#if CONFIG_HAVE_HIGH_TABLES==1
/* Leave some space for ACPI, PIRQ and MP tables */
high_tables_base = (tolmk - HIGH_TABLES_SIZE) * 1024;
high_tables_size = HIGH_TABLES_SIZE * 1024;
-uses HAVE_HIGH_TABLES
+uses CONFIG_HAVE_HIGH_TABLES
config chip.h
driver northbridge.o
driver pciexp_portb.o
driver pciexp_portc.o
-default HAVE_HIGH_TABLES=1
+default CONFIG_HAVE_HIGH_TABLES=1
makerule raminit_test
depends "$(TOP)/src/northbridge/intel/e7520/raminit_test.c"
depends "$(TOP)/src/northbridge/intel/e7520/raminit.c"
- action "$(HOSTCC) $(HOSTCFLAGS) $(CPUFLAGS) -Wno-unused-function -I$(TOP)/src/include -g $< -o $@"
+ action "$(CONFIG_HOSTCC) $(HOSTCFLAGS) $(CPUFLAGS) -Wno-unused-function -I$(TOP)/src/include -g $< -o $@"
end
return tolm;
}
-#if HAVE_HIGH_TABLES==1
+#if CONFIG_HAVE_HIGH_TABLES==1
#define HIGH_TABLES_SIZE 64 // maximum size of high tables in KB
extern uint64_t high_tables_base, high_tables_size;
#endif
(remaplimitk + 64*1024) - remapbasek);
}
-#if HAVE_HIGH_TABLES==1
+#if CONFIG_HAVE_HIGH_TABLES==1
/* Leave some space for ACPI, PIRQ and MP tables */
high_tables_base = (tolmk - HIGH_TABLES_SIZE) * 1024;
high_tables_size = HIGH_TABLES_SIZE * 1024;
-uses HAVE_HIGH_TABLES
+uses CONFIG_HAVE_HIGH_TABLES
config chip.h
driver northbridge.o
driver pciexp_portb.o
driver pciexp_portc.o
-default HAVE_HIGH_TABLES=1
+default CONFIG_HAVE_HIGH_TABLES=1
makerule raminit_test
depends "$(TOP)/src/northbridge/intel/e7525/raminit_test.c"
depends "$(TOP)/src/northbridge/intel/e7525/raminit.c"
- action "$(HOSTCC) $(HOSTCFLAGS) $(CPUFLAGS) -Wno-unused-function -I$(TOP)/src/include -g $< -o $@"
+ action "$(CONFIG_HOSTCC) $(HOSTCFLAGS) $(CPUFLAGS) -Wno-unused-function -I$(TOP)/src/include -g $< -o $@"
end
return tolm;
}
-#if HAVE_HIGH_TABLES==1
+#if CONFIG_HAVE_HIGH_TABLES==1
#define HIGH_TABLES_SIZE 64 // maximum size of high tables in KB
extern uint64_t high_tables_base, high_tables_size;
#endif
(remaplimitk + 64*1024) - remapbasek);
}
-#if HAVE_HIGH_TABLES==1
+#if CONFIG_HAVE_HIGH_TABLES==1
/* Leave some space for ACPI, PIRQ and MP tables */
high_tables_base = (tolmk - HIGH_TABLES_SIZE) * 1024;
high_tables_size = HIGH_TABLES_SIZE * 1024;
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_HIGH_TABLES
+uses CONFIG_HAVE_HIGH_TABLES
config chip.h
driver northbridge.o
driver pciexp_porta.o
-default HAVE_HIGH_TABLES=1
+default CONFIG_HAVE_HIGH_TABLES=1
return tolm;
}
-#if HAVE_HIGH_TABLES==1
+#if CONFIG_HAVE_HIGH_TABLES==1
#define HIGH_TABLES_SIZE 64 // maximum size of high tables in KB
extern uint64_t high_tables_base, high_tables_size;
#endif
(remaplimitk + 64*1024) - remapbasek);
}
-#if HAVE_HIGH_TABLES==1
+#if CONFIG_HAVE_HIGH_TABLES==1
/* Leave some space for ACPI, PIRQ and MP tables */
high_tables_base = (tolmk - HIGH_TABLES_SIZE) * 1024;
high_tables_size = HIGH_TABLES_SIZE * 1024;
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_HIGH_TABLES
+uses CONFIG_HAVE_HIGH_TABLES
config chip.h
driver northbridge.o
-default HAVE_HIGH_TABLES=1
+default CONFIG_HAVE_HIGH_TABLES=1
return tolm;
}
-#if HAVE_HIGH_TABLES==1
+#if CONFIG_HAVE_HIGH_TABLES==1
#define HIGH_TABLES_SIZE 64 // maximum size of high tables in KB
extern uint64_t high_tables_base, high_tables_size;
#endif
ram_resource(dev, idx++, 0, 640);
ram_resource(dev, idx++, 768, tolmk - 768);
-#if HAVE_HIGH_TABLES==1
+#if CONFIG_HAVE_HIGH_TABLES==1
/* Leave some space for ACPI, PIRQ and MP tables */
high_tables_base = (tomk - HIGH_TABLES_SIZE) * 1024;
high_tables_size = HIGH_TABLES_SIZE * 1024;
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_HIGH_TABLES
+uses CONFIG_HAVE_HIGH_TABLES
config chip.h
driver northbridge.o
-default HAVE_HIGH_TABLES=1
+default CONFIG_HAVE_HIGH_TABLES=1
/* MB */0, 8, 0, 16, 16, 24, 32, 32, 48, 64, 64, 96, 128, 128, 192, 256,
};
-#if HAVE_HIGH_TABLES==1
+#if CONFIG_HAVE_HIGH_TABLES==1
#define HIGH_TABLES_SIZE 64 // maximum size of high tables in KB
extern uint64_t high_tables_base, high_tables_size;
#endif
ram_resource(dev, idx++, 0, 640);
ram_resource(dev, idx++, 768, tolmk - 768);
-#if HAVE_HIGH_TABLES==1
+#if CONFIG_HAVE_HIGH_TABLES==1
/* Leave some space for ACPI, PIRQ and MP tables */
high_tables_base = (tomk - HIGH_TABLES_SIZE) * 1024;
high_tables_size = HIGH_TABLES_SIZE * 1024;
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_HIGH_TABLES
+uses CONFIG_HAVE_HIGH_TABLES
config chip.h
driver northbridge.o
driver vga.o
-default HAVE_HIGH_TABLES=1
+default CONFIG_HAVE_HIGH_TABLES=1
return tolm;
}
-#if HAVE_HIGH_TABLES==1
+#if CONFIG_HAVE_HIGH_TABLES==1
#define HIGH_TABLES_SIZE 64 // maximum size of high tables in KB
extern uint64_t high_tables_base, high_tables_size;
#endif
ram_resource(dev, idx++, 0, 640);
ram_resource(dev, idx++, 1024, tolmk - 1024);
-#if HAVE_HIGH_TABLES==1
+#if CONFIG_HAVE_HIGH_TABLES==1
/* Leave some space for ACPI, PIRQ and MP tables */
high_tables_base = (tomk - HIGH_TABLES_SIZE) * 1024;
high_tables_size = HIGH_TABLES_SIZE * 1024;
* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*/
-uses HAVE_HIGH_TABLES
+uses CONFIG_HAVE_HIGH_TABLES
config chip.h
object northbridge.o
-default HAVE_HIGH_TABLES=1
+default CONFIG_HAVE_HIGH_TABLES=1
return tolm;
}
-#if HAVE_HIGH_TABLES==1
+#if CONFIG_HAVE_HIGH_TABLES==1
#define HIGH_TABLES_SIZE 64 // maximum size of high tables in KB
extern uint64_t high_tables_base, high_tables_size;
#endif
/* ram_resource(dev, idx++, 1024, tolmk - 1024); */
ram_resource(dev, idx++, 768, tolmk - 768);
-#if HAVE_HIGH_TABLES==1
+#if CONFIG_HAVE_HIGH_TABLES==1
/* Leave some space for ACPI, PIRQ and MP tables */
high_tables_base = (tomk - HIGH_TABLES_SIZE) * 1024;
high_tables_size = HIGH_TABLES_SIZE * 1024;
-uses HAVE_HIGH_TABLES
+uses CONFIG_HAVE_HIGH_TABLES
config chip.h
object northbridge.o
-default HAVE_HIGH_TABLES=1
+default CONFIG_HAVE_HIGH_TABLES=1
return tolm;
}
-#if HAVE_HIGH_TABLES==1
+#if CONFIG_HAVE_HIGH_TABLES==1
#define HIGH_TABLES_SIZE 64 // maximum size of high tables in KB
extern uint64_t high_tables_base, high_tables_size;
#endif
ram_resource(dev, idx++, 0, 640);
ram_resource(dev, idx++, 768, tolmk - 768);
-#if HAVE_HIGH_TABLES==1
+#if CONFIG_HAVE_HIGH_TABLES==1
/* Leave some space for ACPI, PIRQ and MP tables */
high_tables_base = (tomk - HIGH_TABLES_SIZE) * 1024;
high_tables_size = HIGH_TABLES_SIZE * 1024;
# Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
#
-uses HAVE_HIGH_TABLES
+uses CONFIG_HAVE_HIGH_TABLES
-default HAVE_HIGH_TABLES=1
+default CONFIG_HAVE_HIGH_TABLES=1
config chip.h
driver northbridge.o
return tolm;
}
-#if HAVE_HIGH_TABLES==1
+#if CONFIG_HAVE_HIGH_TABLES==1
#define HIGH_TABLES_SIZE 64 // maximum size of high tables in KB
extern uint64_t high_tables_base, high_tables_size;
#endif
assign_resources(&dev->link[0]);
-#if HAVE_HIGH_TABLES==1
+#if CONFIG_HAVE_HIGH_TABLES==1
/* Leave some space for ACPI, PIRQ and MP tables */
high_tables_base = (tomk - HIGH_TABLES_SIZE) * 1024;
high_tables_size = HIGH_TABLES_SIZE * 1024;
.enable_resources = enable_childrens_resources,
.init = 0,
.scan_bus = pci_domain_scan_bus,
-#if MMCONF_SUPPORT_DEFAULT
+#if CONFIG_MMCONF_SUPPORT_DEFAULT
.ops_pci_bus = &pci_ops_mmconf,
#else
.ops_pci_bus = &pci_cf8_conf1,
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_HIGH_TABLES
+uses CONFIG_HAVE_HIGH_TABLES
config chip.h
driver agp.o
driver vga.o
-default HAVE_HIGH_TABLES=1
+default CONFIG_HAVE_HIGH_TABLES=1
return tolm;
}
-#if HAVE_HIGH_TABLES==1
+#if CONFIG_HAVE_HIGH_TABLES==1
/* maximum size of high tables in KB */
#define HIGH_TABLES_SIZE 64
extern uint64_t high_tables_base, high_tables_size;
tolmk = tomk;
}
-#if HAVE_HIGH_TABLES == 1
+#if CONFIG_HAVE_HIGH_TABLES == 1
high_tables_base = (tolmk - HIGH_TABLES_SIZE) * 1024;
high_tables_size = HIGH_TABLES_SIZE* 1024;
printk_debug("tom: %lx, high_tables_base: %llx, high_tables_size: %llx\n", tomk*1024, high_tables_base, high_tables_size);
print_debug("Copying BOCHS BIOS to 0xf000\n");
/*
- * Copy BOCHS BIOS from 4G-ROM_SIZE-64k (in flash) to 0xf0000 (in RAM)
+ * Copy BOCHS BIOS from 4G-CONFIG_ROM_SIZE-64k (in flash) to 0xf0000 (in RAM)
* This is for compatibility with the VGA ROM's BIOS callbacks.
*/
- memcpy(0xf0000, (0xffffffff - ROM_SIZE - 0xffff), 0x10000);
+ memcpy(0xf0000, (0xffffffff - CONFIG_ROM_SIZE - 0xffff), 0x10000);
printk_debug("Initializing VGA\n");
## along with this program; if not, write to the Free Software
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
-uses HAVE_HIGH_TABLES
+uses CONFIG_HAVE_HIGH_TABLES
config chip.h
driver cx700_sata.o
driver cx700_vga.o
-default HAVE_HIGH_TABLES=1
+default CONFIG_HAVE_HIGH_TABLES=1
return tolm;
}
-#if HAVE_HIGH_TABLES==1
+#if CONFIG_HAVE_HIGH_TABLES==1
/* maximum size of high tables in KB */
#define HIGH_TABLES_SIZE 64
extern uint64_t high_tables_base, high_tables_size;
tolmk -= 1024; // TOP 1M SM Memory
}
-#if HAVE_HIGH_TABLES == 1
+#if CONFIG_HAVE_HIGH_TABLES == 1
high_tables_base = (tolmk - HIGH_TABLES_SIZE) * 1024;
high_tables_size = HIGH_TABLES_SIZE* 1024;
printk_debug("tom: %lx, high_tables_base: %llx, high_tables_size: %llx\n", tomk*1024, high_tables_base, high_tables_size);
-uses HAVE_HIGH_TABLES
+uses CONFIG_HAVE_HIGH_TABLES
config chip.h
driver northbridge.o
-default HAVE_HIGH_TABLES=1
+default CONFIG_HAVE_HIGH_TABLES=1
return tolm;
}
-#if HAVE_HIGH_TABLES==1
+#if CONFIG_HAVE_HIGH_TABLES==1
/* maximum size of high tables in KB */
#define HIGH_TABLES_SIZE 64
extern uint64_t high_tables_base, high_tables_size;
tolmk = tomk;
}
-#if HAVE_HIGH_TABLES == 1
+#if CONFIG_HAVE_HIGH_TABLES == 1
high_tables_base = (tolmk - HIGH_TABLES_SIZE) * 1024;
high_tables_size = HIGH_TABLES_SIZE* 1024;
printk_debug("tom: %lx, high_tables_base: %llx, high_tables_size: %llx\n", tomk*1024, high_tables_base, high_tables_size);
-uses HAVE_HIGH_TABLES
+uses CONFIG_HAVE_HIGH_TABLES
config chip.h
driver northbridge.o
-default HAVE_HIGH_TABLES=1
+default CONFIG_HAVE_HIGH_TABLES=1
return tolm;
}
-#if HAVE_HIGH_TABLES==1
+#if CONFIG_HAVE_HIGH_TABLES==1
/* maximum size of high tables in KB */
#define HIGH_TABLES_SIZE 64
extern uint64_t high_tables_base, high_tables_size;
tolmk = tomk;
}
-#if HAVE_HIGH_TABLES == 1
+#if CONFIG_HAVE_HIGH_TABLES == 1
high_tables_base = (tolmk - HIGH_TABLES_SIZE) * 1024;
high_tables_size = HIGH_TABLES_SIZE* 1024;
printk_debug("tom: %lx, high_tables_base: %llx, high_tables_size: %llx\n", tomk*1024, high_tables_base, high_tables_size);
Only the code around CLEAR_FIRST_1M_RAM is changed.
I remove all the code around CLEAR_FIRST_1M_RAM and #include "cpu/x86/car/cache_as_ram_post.c"
the CLEAR_FIRST_1M_RAM seems to make cpu/x86/car/cache_as_ram_post.c stop at somewhere,
-and cpu/x86/car/cache_as_ram_post.c do not cache my $XIP_ROM_BASE+SIZE area.
+and cpu/x86/car/cache_as_ram_post.c do not cache my $CONFIG_XIP_ROM_BASE+SIZE area.
So,I use: #include "cpu/via/car/cache_as_ram_post.c". my via-version post.c have some diff withx86-version
*/
#include "cpu/via/car/cache_as_ram_post.c"
//#include "cpu/x86/car/cache_as_ram_post.c"
__asm__ volatile (
- /* set new esp *//* before _RAMBASE */
+ /* set new esp *//* before CONFIG_RAMBASE */
"subl %0, %%ebp\n\t"
"subl %0, %%esp\n\t"::
- "a" ((DCACHE_RAM_BASE + DCACHE_RAM_SIZE) -
- _RAMBASE)
+ "a" ((CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE) -
+ CONFIG_RAMBASE)
);
{
* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*/
-#if HAVE_ACPI_RESUME == 1
+#if CONFIG_HAVE_ACPI_RESUME == 1
#include <arch/acpi.h>
#endif
#include <../northbridge/via/vx800/vx800.h>
void hardwaremain(int boot_complete)
{
struct lb_memory *lb_mem;
-#if HAVE_ACPI_RESUME == 1
+#if CONFIG_HAVE_ACPI_RESUME == 1
void *wake_vec;
#endif
*/
SECTIONS {
- . = (_ROMBASE + ROM_IMAGE_SIZE - 0x2c) - (__romstrap_end - __romstrap_start);
+ . = (CONFIG_ROMBASE + CONFIG_ROM_IMAGE_SIZE - 0x2c) - (__romstrap_end - __romstrap_start);
.romstrap (.): {
*(.romstrap)
}
printk_debug("RTC Init\n");
-#if HAVE_OPTION_TABLE
+#if CONFIG_HAVE_OPTION_TABLE
/* See if there has been a CMOS power problem. */
x = cmos_read(RTC_VALID);
cmos_invalid = !(x & RTC_VRT);
/* Setup the frequency it operates at */
cmos_write(RTC_FREQ_SELECT_DEFAULT, RTC_FREQ_SELECT);
-#if HAVE_OPTION_TABLE
+#if CONFIG_HAVE_OPTION_TABLE
/* See if there is a LB CMOS checksum error */
- checksum_invalid = !rtc_checksum_valid(LB_CKS_RANGE_START,
- LB_CKS_RANGE_END,LB_CKS_LOC);
+ checksum_invalid = !rtc_checksum_valid(CONFIG_LB_CKS_RANGE_START,
+ CONFIG_LB_CKS_RANGE_END,CONFIG_LB_CKS_LOC);
if(checksum_invalid)
printk_debug("Invalid CMOS LB checksum\n");
}
-#if USE_OPTION_TABLE == 1
+#if CONFIG_USE_OPTION_TABLE == 1
/* This routine returns the value of the requested bits
input bit = bit count from the beginning of the cmos image
length = number of bits to include in the value
if(get_cmos_value(ce->bit, ce->length, dest))
return(-3);
- if(!rtc_checksum_valid(LB_CKS_RANGE_START,
- LB_CKS_RANGE_END,LB_CKS_LOC))
+ if(!rtc_checksum_valid(CONFIG_LB_CKS_RANGE_START,
+ CONFIG_LB_CKS_RANGE_END,CONFIG_LB_CKS_LOC))
return(-4);
return(0);
}
-#endif /* USE_OPTION_TABLE */
+#endif /* CONFIG_USE_OPTION_TABLE */
#include <pc80/mc146818rtc.h>
#include <part/fallback_boot.h>
-#ifndef MAX_REBOOT_CNT
-#error "MAX_REBOOT_CNT not defined"
+#ifndef CONFIG_MAX_REBOOT_CNT
+#error "CONFIG_MAX_REBOOT_CNT not defined"
#endif
-#if MAX_REBOOT_CNT > 15
-#error "MAX_REBOOT_CNT too high"
+#if CONFIG_MAX_REBOOT_CNT > 15
+#error "CONFIG_MAX_REBOOT_CNT too high"
#endif
static unsigned char cmos_read(unsigned char addr)
unsigned long sum, old_sum;
sum = 0;
/* Comput the cmos checksum */
- for(addr = LB_CKS_RANGE_START; addr <= LB_CKS_RANGE_END; addr++) {
+ for(addr = CONFIG_LB_CKS_RANGE_START; addr <= CONFIG_LB_CKS_RANGE_END; addr++) {
sum += cmos_read(addr);
}
sum = (sum & 0xffff) ^ 0xffff;
/* Read the stored checksum */
- old_sum = cmos_read(LB_CKS_LOC) << 8;
- old_sum |= cmos_read(LB_CKS_LOC+1);
+ old_sum = cmos_read(CONFIG_LB_CKS_LOC) << 8;
+ old_sum |= cmos_read(CONFIG_LB_CKS_LOC+1);
return sum == old_sum;
}
*/
byte = cmos_read(RTC_BOOT_BYTE);
byte &= 0x0c;
- byte |= MAX_REBOOT_CNT << 4;
+ byte |= CONFIG_MAX_REBOOT_CNT << 4;
cmos_write(byte, RTC_BOOT_BYTE);
}
/* Properly set the last boot flag */
byte &= 0xfc;
- if ((byte >> 4) < MAX_REBOOT_CNT) {
+ if ((byte >> 4) < CONFIG_MAX_REBOOT_CNT) {
byte |= (1<<1);
}
/* Are we already at the max count? */
- if ((byte >> 4) < MAX_REBOOT_CNT) {
+ if ((byte >> 4) < CONFIG_MAX_REBOOT_CNT) {
byte += 1 << 4; /* No, add 1 to the count */
}
else {
static unsigned read_option(unsigned start, unsigned size, unsigned def)
{
-#if USE_OPTION_TABLE == 1
+#if CONFIG_USE_OPTION_TABLE == 1
unsigned byte;
byte = cmos_read(start/8);
return (byte >> (start & 7U)) & ((1U << size) - 1U);
#include <part/fallback_boot.h>
/* Base Address */
-#ifndef TTYS0_BASE
-#define TTYS0_BASE 0x3f8
+#ifndef CONFIG_TTYS0_BASE
+#define CONFIG_TTYS0_BASE 0x3f8
#endif
-#ifndef TTYS0_BAUD
-#define TTYS0_BAUD 115200
+#ifndef CONFIG_TTYS0_BAUD
+#define CONFIG_TTYS0_BAUD 115200
#endif
-#if ((115200%TTYS0_BAUD) != 0)
+#if ((115200%CONFIG_TTYS0_BAUD) != 0)
#error Bad ttys0 baud rate
#endif
-#define TTYS0_DIV (115200/TTYS0_BAUD)
+#define CONFIG_TTYS0_DIV (115200/CONFIG_TTYS0_BAUD)
/* Line Control Settings */
-#ifndef TTYS0_LCS
+#ifndef CONFIG_TTYS0_LCS
/* Set 8bit, 1 stop bit, no parity */
-#define TTYS0_LCS 0x3
+#define CONFIG_TTYS0_LCS 0x3
#endif
-#define UART_LCS TTYS0_LCS
+#define UART_LCS CONFIG_TTYS0_LCS
#if CONFIG_USE_PRINTK_IN_CAR == 0
static int uart_can_tx_byte(void)
{
- return inb(TTYS0_BASE + UART_LSR) & 0x20;
+ return inb(CONFIG_TTYS0_BASE + UART_LSR) & 0x20;
}
static void uart_wait_to_tx_byte(void)
static void uart_wait_until_sent(void)
{
- while(!(inb(TTYS0_BASE + UART_LSR) & 0x40))
+ while(!(inb(CONFIG_TTYS0_BASE + UART_LSR) & 0x40))
;
}
static void uart_tx_byte(unsigned char data)
{
uart_wait_to_tx_byte();
- outb(data, TTYS0_BASE + UART_TBR);
+ outb(data, CONFIG_TTYS0_BASE + UART_TBR);
/* Make certain the data clears the fifos */
uart_wait_until_sent();
}
static void uart_init(void)
{
/* disable interrupts */
- outb(0x0, TTYS0_BASE + UART_IER);
+ outb(0x0, CONFIG_TTYS0_BASE + UART_IER);
/* enable fifo's */
- outb(0x01, TTYS0_BASE + UART_FCR);
+ outb(0x01, CONFIG_TTYS0_BASE + UART_FCR);
/* Set Baud Rate Divisor to 12 ==> 115200 Baud */
- outb(0x80 | UART_LCS, TTYS0_BASE + UART_LCR);
-#if USE_OPTION_TABLE == 1
+ outb(0x80 | UART_LCS, CONFIG_TTYS0_BASE + UART_LCR);
+#if CONFIG_USE_OPTION_TABLE == 1
static const unsigned char divisor[] = { 1,2,3,6,12,24,48,96 };
unsigned ttys0_div, ttys0_index;
ttys0_index = read_option(CMOS_VSTART_baud_rate, CMOS_VLEN_baud_rate, 0);
ttys0_index &= 7;
ttys0_div = divisor[ttys0_index];
- outb(ttys0_div & 0xff, TTYS0_BASE + UART_DLL);
- outb(0, TTYS0_BASE + UART_DLM);
+ outb(ttys0_div & 0xff, CONFIG_TTYS0_BASE + UART_DLL);
+ outb(0, CONFIG_TTYS0_BASE + UART_DLM);
#else
- outb(TTYS0_DIV & 0xFF, TTYS0_BASE + UART_DLL);
- outb((TTYS0_DIV >> 8) & 0xFF, TTYS0_BASE + UART_DLM);
+ outb(CONFIG_TTYS0_DIV & 0xFF, CONFIG_TTYS0_BASE + UART_DLL);
+ outb((CONFIG_TTYS0_DIV >> 8) & 0xFF, CONFIG_TTYS0_BASE + UART_DLM);
#endif
- outb(UART_LCS, TTYS0_BASE + UART_LCR);
+ outb(UART_LCS, CONFIG_TTYS0_BASE + UART_LCR);
}
#else
extern void uart8250_init(unsigned base_port, unsigned divisor, unsigned lcs);
void uart_init(void)
{
-#if USE_OPTION_TABLE == 1
+#if CONFIG_USE_OPTION_TABLE == 1
static const unsigned char divisor[] = { 1,2,3,6,12,24,48,96 };
unsigned ttys0_div, ttys0_index;
ttys0_index = read_option(CMOS_VSTART_baud_rate, CMOS_VLEN_baud_rate, 0);
ttys0_index &= 7;
ttys0_div = divisor[ttys0_index];
- uart8250_init(TTYS0_BASE, ttys0_div, UART_LCS);
+ uart8250_init(CONFIG_TTYS0_BASE, ttys0_div, UART_LCS);
#else
- uart8250_init(TTYS0_BASE, TTYS0_DIV, UART_LCS);
+ uart8250_init(CONFIG_TTYS0_BASE, CONFIG_TTYS0_DIV, UART_LCS);
#endif
}
#endif
static void early_usbdebug_direct_init(void)
{
struct ehci_debug_info *dbg_info =
- (struct ehci_debug_info *)(DCACHE_RAM_BASE + DCACHE_RAM_SIZE - sizeof (struct ehci_debug_info));
+ (struct ehci_debug_info *)(CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE - sizeof (struct ehci_debug_info));
usbdebug_direct_init(EHCI_BAR, EHCI_DEBUG_OFFSET, dbg_info);
}
void usbdebug_direct_tx_byte(unsigned char data)
{
struct ehci_debug_info *dbg_info;
- dbg_info = (struct ehci_debug_info *)(DCACHE_RAM_BASE + DCACHE_RAM_SIZE - sizeof (struct ehci_debug_info)); // in Cache
+ dbg_info = (struct ehci_debug_info *)(CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE - sizeof (struct ehci_debug_info)); // in Cache
if (dbg_info->ehci_debug) {
dbgp_bulk_write_x(dbg_info, &data, 1);
}
static void write_phys(unsigned long addr, unsigned long value)
{
-#if HAVE_MOVNTI
+#if CONFIG_HAVE_MOVNTI
asm volatile(
"movnti %1, (%0)"
: /* outputs */
#define SLOW_CPU_OFF 0
#define SLOW_CPU__ON 1
-#ifndef MAINBOARD_POWER_ON_AFTER_POWER_FAIL
-#define MAINBOARD_POWER_ON_AFTER_POWER_FAIL MAINBOARD_POWER_ON
+#ifndef CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+#define CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL MAINBOARD_POWER_ON
#endif
return do_smbus_write_byte(res->base, device, address, val);
}
-#if HAVE_ACPI_TABLES == 1
+#if CONFIG_HAVE_ACPI_TABLES == 1
unsigned pm_base;
#endif
pci_write_config8(dev, 0x41, byte | (1<<6)|(1<<5));
/* power on after power fail */
- on = MAINBOARD_POWER_ON_AFTER_POWER_FAIL;
+ on = CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL;
get_option(&on, "power_on_after_fail");
byte = pci_read_config8(dev, PREVIOUS_POWER_STATE);
byte &= ~0x40;
(on*12)+(on>>1),(on&1)*5);
}
-#if HAVE_ACPI_TABLES == 1
+#if CONFIG_HAVE_ACPI_TABLES == 1
pm_base = pci_read_config16(dev, 0x58) & 0xff00;
printk_debug("pm_base: 0x%04x\n",pm_base);
#endif
#include <device/pci.h>
#include <device/pci_ids.h>
-#if (PIRQ_ROUTE==1 && HAVE_PIRQ_TABLE==1)
+#if (CONFIG_PIRQ_ROUTE==1 && CONFIG_HAVE_PIRQ_TABLE==1)
void pirq_assign_irqs(const unsigned char pIntAtoD[4])
{
device_t pdev;
#include <device/pci.h>
#include <device/pci_ids.h>
-#if (PIRQ_ROUTE==1 && HAVE_PIRQ_TABLE==1)
+#if (CONFIG_PIRQ_ROUTE==1 && CONFIG_HAVE_PIRQ_TABLE==1)
void pirq_assign_irqs(const unsigned char pIntAtoD[4])
{
device_t pdev;
/*CIM set this register; but I didn't find its description in RPR.
On DBM690T platform, I didn't find different between set and skip this register.
- But on Filbert platform, the DEBUG message from serial port on Peanut board can't be displayed
+ But on Filbert platform, the CONFIG_DEBUG message from serial port on Peanut board can't be displayed
after the bit0 of this register is set.
pci_write_config8(dev, 0x04, 0x21);
*/
#define MAINBOARD_POWER_OFF 0
#define MAINBOARD_POWER_ON 1
-#ifndef MAINBOARD_POWER_ON_AFTER_POWER_FAIL
-#define MAINBOARD_POWER_ON_AFTER_POWER_FAIL MAINBOARD_POWER_ON
+#ifndef CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+#define CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL MAINBOARD_POWER_ON
#endif
struct ioapicreg {
pm_iowrite(0x53, byte);
/* power after power fail */
- on = MAINBOARD_POWER_ON_AFTER_POWER_FAIL;
+ on = CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL;
get_option(&on, "power_on_after_fail");
byte = pm_ioread(0x74);
byte &= ~0x03;
* by yinghai.lu@amd.com
*/
-#if USE_FALLBACK_IMAGE == 1
+#if CONFIG_USE_FALLBACK_IMAGE == 1
static void bcm5785_enable_rom(void)
{
byte |=(1<<1)|(1<<0);
pci_write_config8(dev, 0x48, byte);
}
-#endif /* USE_FALLBACK_IMAGE == 1 */
+#endif /* CONFIG_USE_FALLBACK_IMAGE == 1 */
static void bcm5785_enable_wdt_port_cf9(void)
static void check_cmos_failed(void)
{
-#if HAVE_OPTION_TABLE
+#if CONFIG_HAVE_OPTION_TABLE
uint8_t byte = pci_read_config8(PCI_DEV(0,0x1f,0),GEN_PMCON_3);
if( byte & RTC_BATTERY_DEAD) {
// clear reboot_bits
byte = cmos_read(RTC_BOOT_BYTE);
byte &= 0x0c;
- byte |= MAX_REBOOT_CNT << 4;
+ byte |= CONFIG_MAX_REBOOT_CNT << 4;
cmos_write(byte, RTC_BOOT_BYTE);
}
#endif
#define NMI_OFF 0
-#ifndef MAINBOARD_POWER_ON_AFTER_POWER_FAIL
-#define MAINBOARD_POWER_ON_AFTER_POWER_FAIL MAINBOARD_POWER_ON
+#ifndef CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+#define CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL MAINBOARD_POWER_ON
#endif
#define MAINBOARD_POWER_OFF 0
{
uint32_t dword;
int rtc_failed;
- int pwr_on = MAINBOARD_POWER_ON_AFTER_POWER_FAIL;
+ int pwr_on = CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL;
uint8_t pmcon3 = pci_read_config8(dev, GEN_PMCON_3);
rtc_failed = pmcon3 & RTC_BATTERY_DEAD;
//clear bit 1 and bit 2
byte = cmos_read(RTC_BOOT_BYTE);
byte &= 0x0c;
- byte |= MAX_REBOOT_CNT << 4;
+ byte |= CONFIG_MAX_REBOOT_CNT << 4;
cmos_write(byte, RTC_BOOT_BYTE);
}
}
//clear bit 1 and bit 2
byte = cmos_read(RTC_BOOT_BYTE);
byte &= 0x0c;
- byte |= MAX_REBOOT_CNT << 4;
+ byte |= CONFIG_MAX_REBOOT_CNT << 4;
cmos_write(byte, RTC_BOOT_BYTE);
}
}
#define MAINBOARD_POWER_OFF 0
#define MAINBOARD_POWER_ON 1
-#ifndef MAINBOARD_POWER_ON_AFTER_POWER_FAIL
-#define MAINBOARD_POWER_ON_AFTER_POWER_FAIL MAINBOARD_POWER_ON
+#ifndef CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+#define CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL MAINBOARD_POWER_ON
#endif
#define ALL (0xff << 24)
{
uint8_t byte;
uint32_t value;
- int pwr_on=MAINBOARD_POWER_ON_AFTER_POWER_FAIL;
+ int pwr_on=CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL;
/* IO APIC initialization */
value = pci_read_config32(dev, 0xd0);
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_SMI_HANDLER
+uses CONFIG_HAVE_SMI_HANDLER
config chip.h
driver i82801gx.o
object i82801gx_reset.o
object i82801gx_watchdog.o
-if HAVE_SMI_HANDLER
+if CONFIG_HAVE_SMI_HANDLER
object i82801gx_smi.o
smmobject i82801gx_smihandler.o
end
// clear bit 1 and bit 2
byte = cmos_read(RTC_BOOT_BYTE);
byte &= 0x0c;
- byte |= MAX_REBOOT_CNT << 4;
+ byte |= CONFIG_MAX_REBOOT_CNT << 4;
cmos_write(byte, RTC_BOOT_BYTE);
}
}
u8 reg8;
u32 reg32;
-#if MMCONF_SUPPORT
+#if CONFIG_MMCONF_SUPPORT
// ESD
reg32 = pci_mmio_read_config32(dev, 0x134);
reg32 &= 0xff00ffff;
reg32 |= (0x80 << 0); // VCi map
pci_mmio_write_config32(dev, 0x120, reg32);
#else
-#error ICH7 Azalia required MMCONF_SUPPORT
+#error ICH7 Azalia required CONFIG_MMCONF_SUPPORT
#endif
/* Set Bus Master */
u8 reg8;
u16 reg16;
- int pwr_on=MAINBOARD_POWER_ON_AFTER_POWER_FAIL;
+ int pwr_on=CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL;
int nmi_option;
/* Which state do we want to goto after g3 (power restored)?
RCBA32(0x341c) = reg32;
}
-#if HAVE_SMI_HANDLER
+#if CONFIG_HAVE_SMI_HANDLER
static void i82801gx_lock_smm(struct device *dev)
{
void smm_lock(void);
setup_i8259();
-#if HAVE_SMI_HANDLER
+#if CONFIG_HAVE_SMI_HANDLER
i82801gx_lock_smm(dev);
#endif
if (dev->on_mainboard && ops && ops->set_subsystem) {
printk_debug("%s subsystem <- %02x/%02x\n",
dev_path(dev),
- MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID,
- MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID);
+ CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID,
+ CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID);
ops->set_subsystem(dev,
- MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID,
- MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID);
+ CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID,
+ CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID);
}
command = pci_read_config16(dev, PCI_COMMAND);
reg32 |= (1 << 3) | (1 << 2) | (1 << 1) | (1 << 0);
pci_write_config32(dev, 0xe1, reg32);
-#if MMCONF_SUPPORT
+#if CONFIG_MMCONF_SUPPORT
/* Set VC0 transaction class */
reg32 = pci_mmio_read_config32(dev, 0x114);
reg32 &= 0xffffff00;
//clear bit 1 and bit 2
byte = cmos_read(RTC_BOOT_BYTE);
byte &= 0x0c;
- byte |= MAX_REBOOT_CNT << 4;
+ byte |= CONFIG_MAX_REBOOT_CNT << 4;
cmos_write(byte, RTC_BOOT_BYTE);
}
}
-uses HAVE_ACPI_TABLES
+uses CONFIG_HAVE_ACPI_TABLES
config chip.h
driver ck804.o
driver ck804_ht.o
object ck804_reset.o
-if HAVE_ACPI_TABLES
+if CONFIG_HAVE_ACPI_TABLES
object ck804_fadt.o
end
#define CK804_CHIP_REV 3
-#if HT_CHAIN_END_UNITID_BASE < HT_CHAIN_UNITID_BASE
-#define CK804_DEVN_BASE HT_CHAIN_END_UNITID_BASE
+#if CONFIG_HT_CHAIN_END_UNITID_BASE < CONFIG_HT_CHAIN_UNITID_BASE
+#define CK804_DEVN_BASE CONFIG_HT_CHAIN_END_UNITID_BASE
#else
-#define CK804_DEVN_BASE HT_CHAIN_UNITID_BASE
+#define CK804_DEVN_BASE CONFIG_HT_CHAIN_UNITID_BASE
#endif
-#if SB_HT_CHAIN_UNITID_OFFSET_ONLY == 1
+#if CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY == 1
#define CK804B_DEVN_BASE 1
#else
#define CK804B_DEVN_BASE CK804_DEVN_BASE
#define CK804_CHIP_REV 3
-#if HT_CHAIN_END_UNITID_BASE < HT_CHAIN_UNITID_BASE
-#define CK804_DEVN_BASE HT_CHAIN_END_UNITID_BASE
+#if CONFIG_HT_CHAIN_END_UNITID_BASE < CONFIG_HT_CHAIN_UNITID_BASE
+#define CK804_DEVN_BASE CONFIG_HT_CHAIN_END_UNITID_BASE
#else
-#define CK804_DEVN_BASE HT_CHAIN_UNITID_BASE
+#define CK804_DEVN_BASE CONFIG_HT_CHAIN_UNITID_BASE
#endif
-#if SB_HT_CHAIN_UNITID_OFFSET_ONLY == 1
+#if CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY == 1
#define CK804B_DEVN_BASE 1
#else
#define CK804B_DEVN_BASE CK804_DEVN_BASE
* by yhlu@tyan.com
*/
-#if HT_CHAIN_END_UNITID_BASE < HT_CHAIN_UNITID_BASE
-#define CK804_DEVN_BASE HT_CHAIN_END_UNITID_BASE
+#if CONFIG_HT_CHAIN_END_UNITID_BASE < CONFIG_HT_CHAIN_UNITID_BASE
+#define CK804_DEVN_BASE CONFIG_HT_CHAIN_END_UNITID_BASE
#else
-#define CK804_DEVN_BASE HT_CHAIN_UNITID_BASE
+#define CK804_DEVN_BASE CONFIG_HT_CHAIN_UNITID_BASE
#endif
static void ck804_enable_rom(void)
#define SLOW_CPU_OFF 0
#define SLOW_CPU__ON 1
-#ifndef MAINBOARD_POWER_ON_AFTER_POWER_FAIL
-#define MAINBOARD_POWER_ON_AFTER_POWER_FAIL MAINBOARD_POWER_ON
+#ifndef CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+#define CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL MAINBOARD_POWER_ON
#endif
static void lpc_common_init(device_t dev)
#endif
/* power after power fail */
- on = MAINBOARD_POWER_ON_AFTER_POWER_FAIL;
+ on = CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL;
get_option(&on, "power_on_after_fail");
byte = pci_read_config8(dev, PREVIOUS_POWER_STATE);
byte &= ~0x40;
.globl __id_start
__id_start:
vendor:
- .asciz MAINBOARD_VENDOR
+ .asciz CONFIG_MAINBOARD_VENDOR
part:
- .asciz MAINBOARD_PART_NUMBER
+ .asciz CONFIG_MAINBOARD_PART_NUMBER
.long __id_end + 0x80 - vendor /* Reverse offset to the vendor ID */
.long __id_end + 0x80 - part /* Reverse offset to the part number */
-.long PAYLOAD_SIZE + ROM_IMAGE_SIZE /* Size of this ROM image */
+.long CONFIG_PAYLOAD_SIZE + CONFIG_ROM_IMAGE_SIZE /* Size of this ROM image */
.globl __id_end
__id_end:
SECTIONS {
- . = (_ROMBASE + ROM_IMAGE_SIZE - 0x80) - (__id_end - __id_start);
+ . = (CONFIG_ROMBASE + CONFIG_ROM_IMAGE_SIZE - 0x80) - (__id_end - __id_start);
.id (.): {
*(.id)
}
SECTIONS {
- . = (_ROMBASE + ROM_IMAGE_SIZE - 0x10) - (__romstrap_end - __romstrap_start);
+ . = (CONFIG_ROMBASE + CONFIG_ROM_IMAGE_SIZE - 0x10) - (__romstrap_end - __romstrap_start);
.romstrap (.): {
*(.romstrap)
}
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_ACPI_TABLES
+uses CONFIG_HAVE_ACPI_TABLES
config chip.h
driver mcp55.o
driver mcp55_pcie.o
driver mcp55_ht.o
object mcp55_reset.o
-if HAVE_ACPI_TABLES
+if CONFIG_HAVE_ACPI_TABLES
object mcp55_fadt.o
end
.globl __id_start
__id_start:
vendor:
- .asciz MAINBOARD_VENDOR
+ .asciz CONFIG_MAINBOARD_VENDOR
part:
- .asciz MAINBOARD_PART_NUMBER
+ .asciz CONFIG_MAINBOARD_PART_NUMBER
.long __id_end + 0x80 - vendor /* Reverse offset to the vendor id */
.long __id_end + 0x80 - part /* Reverse offset to the part number */
-.long PAYLOAD_SIZE + ROM_IMAGE_SIZE /* Size of this romimage */
+.long CONFIG_PAYLOAD_SIZE + CONFIG_ROM_IMAGE_SIZE /* Size of this romimage */
.globl __id_end
__id_end:
*/
SECTIONS {
- . = (_ROMBASE + ROM_IMAGE_SIZE - 0x80) - (__id_end - __id_start);
+ . = (CONFIG_ROMBASE + CONFIG_ROM_IMAGE_SIZE - 0x80) - (__id_end - __id_start);
.id (.): {
*(.id)
}
* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*/
-#if HT_CHAIN_END_UNITID_BASE != 0x20
- #define MCP55_DEVN_BASE HT_CHAIN_END_UNITID_BASE
+#if CONFIG_HT_CHAIN_END_UNITID_BASE != 0x20
+ #define MCP55_DEVN_BASE CONFIG_HT_CHAIN_END_UNITID_BASE
#else
- #define MCP55_DEVN_BASE HT_CHAIN_UNITID_BASE
+ #define MCP55_DEVN_BASE CONFIG_HT_CHAIN_UNITID_BASE
#endif
static void mcp55_enable_rom(void)
* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*/
-#if HT_CHAIN_END_UNITID_BASE != 0x20
- #define MCP55_DEVN_BASE HT_CHAIN_END_UNITID_BASE
+#if CONFIG_HT_CHAIN_END_UNITID_BASE != 0x20
+ #define MCP55_DEVN_BASE CONFIG_HT_CHAIN_END_UNITID_BASE
#else
- #define MCP55_DEVN_BASE HT_CHAIN_UNITID_BASE
+ #define MCP55_DEVN_BASE CONFIG_HT_CHAIN_UNITID_BASE
#endif
#define EHCI_BAR_INDEX 0x10
#define SLOW_CPU_OFF 0
#define SLOW_CPU__ON 1
-#ifndef MAINBOARD_POWER_ON_AFTER_POWER_FAIL
-#define MAINBOARD_POWER_ON_AFTER_POWER_FAIL MAINBOARD_POWER_ON
+#ifndef CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+#define CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL MAINBOARD_POWER_ON
#endif
static void lpc_common_init(device_t dev, int master)
/* power after power fail */
#if 1
- on = MAINBOARD_POWER_ON_AFTER_POWER_FAIL;
+ on = CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL;
get_option(&on, "power_on_after_fail");
byte = pci_read_config8(dev, PREVIOUS_POWER_STATE);
byte &= ~0x40;
.write_byte = lsmbus_write_byte,
};
-#if HAVE_ACPI_TABLES == 1
+#if CONFIG_HAVE_ACPI_TABLES == 1
unsigned pm_base;
#endif
static void mcp55_sm_init(device_t dev)
{
-#if HAVE_ACPI_TABLES == 1
+#if CONFIG_HAVE_ACPI_TABLES == 1
struct resource *res;
res = find_resource(dev, 0x60);
*/
SECTIONS {
- . = (_ROMBASE + ROM_IMAGE_SIZE - 0x10) - (__romstrap_end - __romstrap_start);
+ . = (CONFIG_ROMBASE + CONFIG_ROM_IMAGE_SIZE - 0x10) - (__romstrap_end - __romstrap_start);
.romstrap (.): {
*(.romstrap)
}
.globl __id_start
__id_start:
vendor:
- .asciz MAINBOARD_VENDOR
+ .asciz CONFIG_MAINBOARD_VENDOR
part:
- .asciz MAINBOARD_PART_NUMBER
+ .asciz CONFIG_MAINBOARD_PART_NUMBER
.long __id_end + 0x80 - vendor /* Reverse offset to the vendor id */
.long __id_end + 0x80 - part /* Reverse offset to the part number */
-.long PAYLOAD_SIZE + ROM_IMAGE_SIZE /* Size of this romimage */
+.long CONFIG_PAYLOAD_SIZE + CONFIG_ROM_IMAGE_SIZE /* Size of this romimage */
.globl __id_end
__id_end:
*/
SECTIONS {
- . = (_ROMBASE + ROM_IMAGE_SIZE - 0x80) - (__id_end - __id_start);
+ . = (CONFIG_ROMBASE + CONFIG_ROM_IMAGE_SIZE - 0x80) - (__id_end - __id_start);
.id (.): {
*(.id)
}
*/
SECTIONS {
- . = (_ROMBASE + ROM_IMAGE_SIZE - 0x10) - (__romstrap_end - __romstrap_start);
+ . = (CONFIG_ROMBASE + CONFIG_ROM_IMAGE_SIZE - 0x10) - (__romstrap_end - __romstrap_start);
.romstrap (.): {
*(.romstrap)
}
* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*/
-#if HT_CHAIN_END_UNITID_BASE < HT_CHAIN_UNITID_BASE
- #define SIS966_DEVN_BASE HT_CHAIN_END_UNITID_BASE
+#if CONFIG_HT_CHAIN_END_UNITID_BASE < CONFIG_HT_CHAIN_UNITID_BASE
+ #define SIS966_DEVN_BASE CONFIG_HT_CHAIN_END_UNITID_BASE
#else
- #define SIS966_DEVN_BASE HT_CHAIN_UNITID_BASE
+ #define SIS966_DEVN_BASE CONFIG_HT_CHAIN_UNITID_BASE
#endif
static void sis966_enable_rom(void)
* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*/
-#if HT_CHAIN_END_UNITID_BASE < HT_CHAIN_UNITID_BASE
- #define SIS966_DEVN_BASE HT_CHAIN_END_UNITID_BASE
+#if CONFIG_HT_CHAIN_END_UNITID_BASE < CONFIG_HT_CHAIN_UNITID_BASE
+ #define SIS966_DEVN_BASE CONFIG_HT_CHAIN_END_UNITID_BASE
#else
- #define SIS966_DEVN_BASE HT_CHAIN_UNITID_BASE
+ #define SIS966_DEVN_BASE CONFIG_HT_CHAIN_UNITID_BASE
#endif
#define EHCI_BAR_INDEX 0x10
#define SLOW_CPU_OFF 0
#define SLOW_CPU__ON 1
-#ifndef MAINBOARD_POWER_ON_AFTER_POWER_FAIL
-#define MAINBOARD_POWER_ON_AFTER_POWER_FAIL MAINBOARD_POWER_ON
+#ifndef CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+#define CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL MAINBOARD_POWER_ON
#endif
static void lpc_common_init(device_t dev)
/* power after power fail */
- on = MAINBOARD_POWER_ON_AFTER_POWER_FAIL;
+ on = CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL;
get_option(&on, "power_on_after_fail");
byte = pci_read_config8(dev, PREVIOUS_POWER_STATE);
byte &= ~0x40;
(proposed_base < ((uint64_t) 0xffffffff) )) {
resmax = res;
}
-#if HAVE_HIGH_TABLES==1
+#if CONFIG_HAVE_HIGH_TABLES==1
/* in arch/i386/boot/tables.c */
extern uint64_t high_tables_base, high_tables_size;
/* Modified for K8T890 ROM strap by Rudolf Marek <r.marek@assembler.cz>. */
SECTIONS {
- . = (_ROMBASE + ROM_IMAGE_SIZE - 0x2c) - (__romstrap_end - __romstrap_start);
+ . = (CONFIG_ROMBASE + CONFIG_ROM_IMAGE_SIZE - 0x2c) - (__romstrap_end - __romstrap_start);
.romstrap (.): {
*(.romstrap)
}
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_ACPI_TABLES
+uses CONFIG_HAVE_ACPI_TABLES
config chip.h
driver vt8237r_ide.o
driver vt8237r_lpc.o
driver vt8237r_sata.o
-if HAVE_ACPI_TABLES
+if CONFIG_HAVE_ACPI_TABLES
object vt8237_fadt.o
end
printk_err("NO HARD RESET ON VT8237R! FIX ME!\n");
}
-#if DEFAULT_CONSOLE_LOGLEVEL > 7
+#if CONFIG_DEFAULT_CONSOLE_LOGLEVEL > 7
void writeback(struct device *dev, u16 where, u8 what)
{
u8 regval;
/* SCI is generated for RTC/pwrBtn/slpBtn. */
tmp = inw(VT8237R_ACPI_IO_BASE + 0x04);
-#if HAVE_ACPI_RESUME == 1
+#if CONFIG_HAVE_ACPI_RESUME == 1
acpi_slp_type = ((tmp & (7 << 10)) >> 10) == 1 ? 3 : 0 ;
printk_debug("SLP_TYP type was %x %x\n", tmp, acpi_slp_type);
#endif
#include <string.h>
#include <pc80/ide.h>
-#ifndef IDE_BOOT_DRIVE
-#define IDE_BOOT_DRIVE 0
+#ifndef CONFIG_IDE_BOOT_DRIVE
+#define CONFIG_IDE_BOOT_DRIVE 0
#endif
static unsigned long offset;
#ifdef ONE_TRACK
offset = (ONE_TRACK*512);
-#elif defined(IDE_OFFSET)
- offset = IDE_OFFSET;
+#elif defined(CONFIG_IDE_OFFSET)
+ offset = CONFIG_IDE_OFFSET;
#else
offset = 0x7e00;
#endif
- res = ide_probe(IDE_BOOT_DRIVE);
+ res = ide_probe(CONFIG_IDE_BOOT_DRIVE);
delay(1);
return res;
}
if (block_num != offs / 512 || first_fill) {
block_num = offs / 512;
printk_notice (".");
- ide_read(IDE_BOOT_DRIVE, block_num, buffer);
+ ide_read(CONFIG_IDE_BOOT_DRIVE, block_num, buffer);
first_fill = 0;
}
/*XXXXXXXXXXXXXX */
unsigned char *rom_start = (unsigned char *)CONFIG_ROM_PAYLOAD_START;
-unsigned char *rom_end = (unsigned char *)(CONFIG_ROM_PAYLOAD_START + PAYLOAD_SIZE - 1);
+unsigned char *rom_end = (unsigned char *)(CONFIG_ROM_PAYLOAD_START + CONFIG_PAYLOAD_SIZE - 1);
/*XXXXXXXXXXXXXX */
static const unsigned char *rom;
dest = &_eheap; /* need a good address on RAM */
-#if _RAMBASE<0x00100000
+#if CONFIG_RAMBASE<0x00100000
olen = *(unsigned int *)dest;
#if (CONFIG_CONSOLE_VGA==1) || (CONFIG_PCI_ROM_RUN == 1)
if((dest < (unsigned char *)0xa0000) && ((dest+olen)>(unsigned char *)0xa0000)) {
pnp_write_config(dev, 0x02, 0x02);
}
-#ifdef HAVE_FANCTL
+#ifdef CONFIG_HAVE_FANCTL
extern void init_ec(uint16_t base);
#else
static void pnp_write_index(uint16_t port_base, uint8_t reg, uint8_t value)
target atc-6220
mainboard a-trend/atc-6220
-option ROM_SIZE = 256 * 1024
+option CONFIG_ROM_SIZE = 256 * 1024
-option MAINBOARD_VENDOR = "A-Trend"
-option MAINBOARD_PART_NUMBER = "ATC-6220"
+option CONFIG_MAINBOARD_VENDOR = "A-Trend"
+option CONFIG_MAINBOARD_PART_NUMBER = "ATC-6220"
-option IRQ_SLOT_COUNT = 7
+option CONFIG_IRQ_SLOT_COUNT = 7
-option DEFAULT_CONSOLE_LOGLEVEL = 9
-option MAXIMUM_CONSOLE_LOGLEVEL = 9
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
option CONFIG_CONSOLE_VGA = 1
option CONFIG_PCI_ROM_RUN = 1
romimage "normal"
- option USE_FALLBACK_IMAGE = 0
+ option CONFIG_USE_FALLBACK_IMAGE = 0
option COREBOOT_EXTRA_VERSION = ".0Normal"
payload /tmp/filo.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE = 1
+ option CONFIG_USE_FALLBACK_IMAGE = 1
option COREBOOT_EXTRA_VERSION = ".0Fallback"
payload /tmp/filo.elf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
target atc-6240
mainboard a-trend/atc-6240
-option ROM_SIZE = 256 * 1024
+option CONFIG_ROM_SIZE = 256 * 1024
-option MAINBOARD_VENDOR = "A-Trend"
-option MAINBOARD_PART_NUMBER = "ATC-6240"
+option CONFIG_MAINBOARD_VENDOR = "A-Trend"
+option CONFIG_MAINBOARD_PART_NUMBER = "ATC-6240"
-option IRQ_SLOT_COUNT = 7
+option CONFIG_IRQ_SLOT_COUNT = 7
-option DEFAULT_CONSOLE_LOGLEVEL = 9
-option MAXIMUM_CONSOLE_LOGLEVEL = 9
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
option CONFIG_CONSOLE_VGA = 1
option CONFIG_PCI_ROM_RUN = 1
romimage "normal"
- option USE_FALLBACK_IMAGE = 0
+ option CONFIG_USE_FALLBACK_IMAGE = 0
option COREBOOT_EXTRA_VERSION = ".0Normal"
payload ../payload.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE = 1
+ option CONFIG_USE_FALLBACK_IMAGE = 1
option COREBOOT_EXTRA_VERSION = ".0Fallback"
payload ../payload.elf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
target be6-ii_v2_0
mainboard abit/be6-ii_v2_0
-option ROM_SIZE = 256 * 1024
+option CONFIG_ROM_SIZE = 256 * 1024
-option MAINBOARD_VENDOR = "Abit"
-option MAINBOARD_PART_NUMBER = "BE6-II V2.0"
+option CONFIG_MAINBOARD_VENDOR = "Abit"
+option CONFIG_MAINBOARD_PART_NUMBER = "BE6-II V2.0"
-option IRQ_SLOT_COUNT = 9
+option CONFIG_IRQ_SLOT_COUNT = 9
-option DEFAULT_CONSOLE_LOGLEVEL = 9
-option MAXIMUM_CONSOLE_LOGLEVEL = 9
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
option CONFIG_CONSOLE_VGA = 1
option CONFIG_PCI_ROM_RUN = 1
romimage "normal"
- option USE_FALLBACK_IMAGE = 0
+ option CONFIG_USE_FALLBACK_IMAGE = 0
option COREBOOT_EXTRA_VERSION = ".0Normal"
payload /tmp/filo.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE = 1
+ option CONFIG_USE_FALLBACK_IMAGE = 1
option COREBOOT_EXTRA_VERSION = ".0Fallback"
payload /tmp/filo.elf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
target pcm-5820
mainboard advantech/pcm-5820
-option ROM_SIZE = 256 * 1024
+option CONFIG_ROM_SIZE = 256 * 1024
-option MAINBOARD_VENDOR = "Advantech"
-option MAINBOARD_PART_NUMBER = "PCM-5820"
+option CONFIG_MAINBOARD_VENDOR = "Advantech"
+option CONFIG_MAINBOARD_PART_NUMBER = "PCM-5820"
-option IRQ_SLOT_COUNT = 2
+option CONFIG_IRQ_SLOT_COUNT = 2
## Enable VGA with a splash screen (only 640x480 to run on most monitors).
## We want to support up to 1024x768@16 so we need 2MiB video memory.
option CONFIG_SPLASH_GRAPHIC = 1
option CONFIG_VIDEO_MB = 2
-option DEFAULT_CONSOLE_LOGLEVEL = 9
-option MAXIMUM_CONSOLE_LOGLEVEL = 9
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
romimage "normal"
- option USE_FALLBACK_IMAGE = 0
+ option CONFIG_USE_FALLBACK_IMAGE = 0
option COREBOOT_EXTRA_VERSION = ".0Normal"
payload /tmp/filo.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE = 1
+ option CONFIG_USE_FALLBACK_IMAGE = 1
option COREBOOT_EXTRA_VERSION = ".0Fallback"
payload /tmp/filo.elf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
option CONFIG_COMPRESSED_PAYLOAD_LZMA=0
# Leave 36k for VSA.
-option ROM_SIZE=512*1024-36*1024
-# option ROM_SIZE=256*1024-36*1024
-option FALLBACK_SIZE=ROM_SIZE
+option CONFIG_ROM_SIZE=512*1024-36*1024
+# option CONFIG_ROM_SIZE=256*1024-36*1024
+option CONFIG_FALLBACK_SIZE=CONFIG_ROM_SIZE
-option DEFAULT_CONSOLE_LOGLEVEL = 9
-option MAXIMUM_CONSOLE_LOGLEVEL = 9
-# option DEFAULT_CONSOLE_LOGLEVEL = 4
-# option MAXIMUM_CONSOLE_LOGLEVEL = 4
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
+# option CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 4
+# option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 4
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=64*1024
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=64*1024
option COREBOOT_EXTRA_VERSION=".0Fallback"
payload ../payload.elf
end
-buildrom ./coreboot.rom ROM_SIZE "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback"
mainboard VENDOR/MAINBOARD
option CC="CROSSCC"
-option CROSS_COMPILE="CROSS_PREFIX"
-option HOSTCC="CROSS_HOSTCC"
+option CONFIG_CROSS_COMPILE="CROSS_PREFIX"
+option CONFIG_HOSTCC="CROSS_HOSTCC"
__COMPRESSION__
__LOGLEVEL__
-option ROM_SIZE=1024*1024
+option CONFIG_ROM_SIZE=1024*1024
romimage "normal"
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=0x20000
- option XIP_ROM_SIZE=0x20000
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+ option CONFIG_XIP_ROM_SIZE=0x20000
option COREBOOT_EXTRA_VERSION=".0-normal"
payload __PAYLOAD__
end
romimage "failover"
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x20000
- option XIP_ROM_SIZE=0x20000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+ option CONFIG_XIP_ROM_SIZE=0x20000
option COREBOOT_EXTRA_VERSION=".0-failover"
payload __PAYLOAD__
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "failover"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "failover"
mainboard amd/dbm690t
romimage "normal"
- option ROM_SIZE = 1024*1024 - 55808
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=0x20000
- option XIP_ROM_SIZE=0x20000
+ option CONFIG_ROM_SIZE = 1024*1024 - 55808
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+ option CONFIG_XIP_ROM_SIZE=0x20000
payload ../payload.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x20000
- option XIP_ROM_SIZE=0x20000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+ option CONFIG_XIP_ROM_SIZE=0x20000
payload ../payload.elf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
option CONFIG_COMPRESSED_PAYLOAD_NRV2B=0
option CONFIG_COMPRESSED_PAYLOAD_LZMA=0
-option ROM_SIZE=512*1024-36*1024
-#option ROM_SIZE=256*1024-36*1024
-option FALLBACK_SIZE=ROM_SIZE
+option CONFIG_ROM_SIZE=512*1024-36*1024
+#option CONFIG_ROM_SIZE=256*1024-36*1024
+option CONFIG_FALLBACK_SIZE=CONFIG_ROM_SIZE
-option DEFAULT_CONSOLE_LOGLEVEL = 9
-option MAXIMUM_CONSOLE_LOGLEVEL = 9
-#option DEFAULT_CONSOLE_LOGLEVEL = 4
-#option MAXIMUM_CONSOLE_LOGLEVEL = 4
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
+#option CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 4
+#option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 4
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=64*1024
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=64*1024
option COREBOOT_EXTRA_VERSION=".0Fallback"
payload ../payload.elf
end
-buildrom ./coreboot.rom ROM_SIZE "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback"
mainboard VENDOR/MAINBOARD
option CC="CROSSCC"
-option CROSS_COMPILE="CROSS_PREFIX"
-option HOSTCC="CROSS_HOSTCC"
+option CONFIG_CROSS_COMPILE="CROSS_PREFIX"
+option CONFIG_HOSTCC="CROSS_HOSTCC"
__COMPRESSION__
__LOGLEVEL__
-option ROM_SIZE=1024*1024
+option CONFIG_ROM_SIZE=1024*1024
romimage "normal"
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=0x20000
- option XIP_ROM_SIZE=0x20000
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+ option CONFIG_XIP_ROM_SIZE=0x20000
option COREBOOT_EXTRA_VERSION=".0-normal"
payload __PAYLOAD__
end
romimage "failover"
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x20000
- option XIP_ROM_SIZE=0x20000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+ option CONFIG_XIP_ROM_SIZE=0x20000
option COREBOOT_EXTRA_VERSION=".0-failover"
payload __PAYLOAD__
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "failover"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "failover"
mainboard amd/pistachio
romimage "normal"
- option ROM_SIZE = 1024*1024 - 55808
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=0x20000
- option XIP_ROM_SIZE=0x20000
+ option CONFIG_ROM_SIZE = 1024*1024 - 55808
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+ option CONFIG_XIP_ROM_SIZE=0x20000
payload ../payload.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x20000
- option XIP_ROM_SIZE=0x20000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+ option CONFIG_XIP_ROM_SIZE=0x20000
payload ../payload.elf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
target rumba
mainboard amd/rumba
-option ROM_SIZE=256*1024
+option CONFIG_ROM_SIZE=256*1024
romimage "normal"
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=0x10000
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=0x10000
option COREBOOT_EXTRA_VERSION=".0Normal"
# payload /usr/share/etherboot/5.1.9pre2-lnxi-lb/tg3--ide_disk.zelf
# payload ../../../../tg3--ide_disk.zelf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x10000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x10000
option COREBOOT_EXTRA_VERSION=".0Fallback"
# payload /usr/share/etherboot/5.1.9pre2-lnxi-lb/tg3--ide_disk.zelf
# payload ../../../../tg3--ide_disk.zelf
payload /tmp/filo.elf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
target rumba
mainboard amd/rumba
-option ROM_SIZE=128*1024
-option FALLBACK_SIZE=ROM_SIZE
-#option FALLBACK_SIZE=65535
+option CONFIG_ROM_SIZE=128*1024
+option CONFIG_FALLBACK_SIZE=CONFIG_ROM_SIZE
+#option CONFIG_FALLBACK_SIZE=65535
#romimage "normal"
-# option USE_FALLBACK_IMAGE=0
-# option ROM_IMAGE_SIZE=0x10000
+# option CONFIG_USE_FALLBACK_IMAGE=0
+# option CONFIG_ROM_IMAGE_SIZE=0x10000
# option COREBOOT_EXTRA_VERSION=".0Normal"
# payload /usr/share/etherboot/5.1.9pre2-lnxi-lb/tg3--ide_disk.zelf
# payload ../../../../tg3--ide_disk.zelf
#end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x10000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x10000
option COREBOOT_EXTRA_VERSION=".0Fallback"
# payload /usr/share/etherboot/5.1.9pre2-lnxi-lb/tg3--ide_disk.zelf
# payload ../../../../tg3--ide_disk.zelf
# payload /home/ollie/work/filo-0.4.1/filo.elf
end
-#buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
-buildrom ./coreboot.rom ROM_SIZE "fallback"
+#buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback"
mainboard VENDOR/MAINBOARD
option CC="CROSSCC"
-option CROSS_COMPILE="CROSS_PREFIX"
-option HOSTCC="CROSS_HOSTCC"
+option CONFIG_CROSS_COMPILE="CROSS_PREFIX"
+option CONFIG_HOSTCC="CROSS_HOSTCC"
__COMPRESSION__
__LOGLEVEL__
romimage "normal"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=0x20000
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
option COREBOOT_EXTRA_VERSION=".0-normal"
payload __PAYLOAD__
end
romimage "fallback"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x20000
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
option COREBOOT_EXTRA_VERSION=".0-fallback"
payload __PAYLOAD__
end
romimage "failover"
- option USE_FAILOVER_IMAGE=1
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=FAILOVER_SIZE
- option XIP_ROM_SIZE=FAILOVER_SIZE
+ option CONFIG_USE_FAILOVER_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=CONFIG_FAILOVER_SIZE
+ option CONFIG_XIP_ROM_SIZE=CONFIG_FAILOVER_SIZE
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback" "failover"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback" "failover"
target serengeti_cheetah
mainboard amd/serengeti_cheetah
-option ROM_SIZE = 0x100000
-option USE_FAILOVER_IMAGE=0
-option HAVE_FAILOVER_BOOT=0
-option FAILOVER_SIZE=0
+option CONFIG_ROM_SIZE = 0x100000
+option CONFIG_USE_FAILOVER_IMAGE=0
+option CONFIG_HAVE_FAILOVER_BOOT=0
+option CONFIG_FAILOVER_SIZE=0
romimage "fallback"
option CONFIG_PRECOMPRESSED_PAYLOAD=1
option CONFIG_COMPRESSED_PAYLOAD_LZMA=1
- option FALLBACK_SIZE=ROM_SIZE
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x1a000
- option XIP_ROM_SIZE=0x40000
+ option CONFIG_FALLBACK_SIZE=CONFIG_ROM_SIZE
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x1a000
+ option CONFIG_XIP_ROM_SIZE=0x40000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Normal"
payload ../payload.elf.lzma
end
-buildrom ./coreboot.rom ROM_SIZE "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback"
# serengeti_leopard
romimage "normal"
# 48K for SCSI FW
-# option ROM_SIZE = 475136
+# option CONFIG_ROM_SIZE = 475136
# 48K for SCSI FW and 48K for ATI ROM
-# option ROM_SIZE = 425984
+# option CONFIG_ROM_SIZE = 425984
# 64K for Etherboot
-# option ROM_SIZE = 458752
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=0
-# option ROM_IMAGE_SIZE=0x13800
-# option ROM_IMAGE_SIZE=0x18800
- option ROM_IMAGE_SIZE=0x20000
-# option ROM_IMAGE_SIZE=0x15800
- option XIP_ROM_SIZE=0x40000
+# option CONFIG_ROM_SIZE = 458752
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=0
+# option CONFIG_ROM_IMAGE_SIZE=0x13800
+# option CONFIG_ROM_IMAGE_SIZE=0x18800
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+# option CONFIG_ROM_IMAGE_SIZE=0x15800
+ option CONFIG_XIP_ROM_SIZE=0x40000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Normal"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
end
romimage "fallback"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=1
-# option ROM_IMAGE_SIZE=0x13800
-# option ROM_IMAGE_SIZE=0x19800
- option ROM_IMAGE_SIZE=0x20000
-# option ROM_IMAGE_SIZE=0x15800
- option XIP_ROM_SIZE=0x40000
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=1
+# option CONFIG_ROM_IMAGE_SIZE=0x13800
+# option CONFIG_ROM_IMAGE_SIZE=0x19800
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+# option CONFIG_ROM_IMAGE_SIZE=0x15800
+ option CONFIG_XIP_ROM_SIZE=0x40000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
end
romimage "failover"
- option USE_FAILOVER_IMAGE=1
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=FAILOVER_SIZE
- option XIP_ROM_SIZE=FAILOVER_SIZE
+ option CONFIG_USE_FAILOVER_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=CONFIG_FAILOVER_SIZE
+ option CONFIG_XIP_ROM_SIZE=CONFIG_FAILOVER_SIZE
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Failover"
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback" "failover"
-#buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback" "failover"
+#buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
mainboard VENDOR/MAINBOARD
option CC="CROSSCC"
-option CROSS_COMPILE="CROSS_PREFIX"
-option HOSTCC="CROSS_HOSTCC"
+option CONFIG_CROSS_COMPILE="CROSS_PREFIX"
+option CONFIG_HOSTCC="CROSS_HOSTCC"
__COMPRESSION__
__LOGLEVEL__
-option ROM_SIZE=1024*1024
+option CONFIG_ROM_SIZE=1024*1024
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x3f000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x3f000
option COREBOOT_EXTRA_VERSION=".0-fallback"
payload __PAYLOAD__
end
romimage "failover"
- option USE_FAILOVER_IMAGE=1
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=FAILOVER_SIZE
- option XIP_ROM_SIZE=FAILOVER_SIZE
+ option CONFIG_USE_FAILOVER_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=CONFIG_FAILOVER_SIZE
+ option CONFIG_XIP_ROM_SIZE=CONFIG_FAILOVER_SIZE
option COREBOOT_EXTRA_VERSION=".0-failover"
end
-buildrom ./coreboot.rom ROM_SIZE "fallback" "failover"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback" "failover"
target serengeti_cheetah_fam10
mainboard amd/serengeti_cheetah_fam10
# Request this level of debugging output
- option DEFAULT_CONSOLE_LOGLEVEL=9
+ option CONFIG_DEFAULT_CONSOLE_LOGLEVEL=9
# At a maximum only compile in this level of debugging
- option MAXIMUM_CONSOLE_LOGLEVEL=9
+ option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=9
# 1024KB ROM
-option ROM_SIZE=1024*1024
-option FALLBACK_SIZE=ROM_SIZE-FAILOVER_SIZE
+option CONFIG_ROM_SIZE=1024*1024
+option CONFIG_FALLBACK_SIZE=CONFIG_ROM_SIZE-CONFIG_FAILOVER_SIZE
romimage "fallback"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x30000
- option XIP_ROM_SIZE=0x40000
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x30000
+ option CONFIG_XIP_ROM_SIZE=0x40000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
payload ../payload.elf.lzma
end
romimage "failover"
- option USE_FAILOVER_IMAGE=1
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=FAILOVER_SIZE
- option XIP_ROM_SIZE=FAILOVER_SIZE
+ option CONFIG_USE_FAILOVER_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=CONFIG_FAILOVER_SIZE
+ option CONFIG_XIP_ROM_SIZE=CONFIG_FAILOVER_SIZE
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Failover"
end
-buildrom ./coreboot.rom ROM_SIZE "fallback" "failover"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback" "failover"
target serengeti_cheetah_fam10
mainboard amd/serengeti_cheetah_fam10
# Request this level of debugging output
- option DEFAULT_CONSOLE_LOGLEVEL=9
+ option CONFIG_DEFAULT_CONSOLE_LOGLEVEL=9
# At a maximum only compile in this level of debugging
- option MAXIMUM_CONSOLE_LOGLEVEL=9
+ option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=9
# 512KB ROM
-option ROM_SIZE=1024*1024
+option CONFIG_ROM_SIZE=1024*1024
# Cheetah Family 10
#romimage "normal"
# 1MB ROM
-# option ROM_SIZE = 0x100000
-# option USE_FAILOVER_IMAGE=0
-# option USE_FALLBACK_IMAGE=0
-# option ROM_IMAGE_SIZE=0x20000
-# option ROM_IMAGE_SIZE=0x30000
-# option XIP_ROM_SIZE=0x40000
+# option CONFIG_ROM_SIZE = 0x100000
+# option CONFIG_USE_FAILOVER_IMAGE=0
+# option CONFIG_USE_FALLBACK_IMAGE=0
+# option CONFIG_ROM_IMAGE_SIZE=0x20000
+# option CONFIG_ROM_IMAGE_SIZE=0x30000
+# option CONFIG_XIP_ROM_SIZE=0x40000
# option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Normal"
# payload ../payload.elf
#end
romimage "fallback"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=1
-# option ROM_IMAGE_SIZE=0x13800
-# option ROM_IMAGE_SIZE=0x19800
- option ROM_IMAGE_SIZE=0x7f000
-# option ROM_IMAGE_SIZE=0x15800
- option XIP_ROM_SIZE=0x80000
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=1
+# option CONFIG_ROM_IMAGE_SIZE=0x13800
+# option CONFIG_ROM_IMAGE_SIZE=0x19800
+ option CONFIG_ROM_IMAGE_SIZE=0x7f000
+# option CONFIG_ROM_IMAGE_SIZE=0x15800
+ option CONFIG_XIP_ROM_SIZE=0x80000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
payload ../payload.elf
end
romimage "failover"
- option USE_FAILOVER_IMAGE=1
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=FAILOVER_SIZE
- option XIP_ROM_SIZE=FAILOVER_SIZE
+ option CONFIG_USE_FAILOVER_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=CONFIG_FAILOVER_SIZE
+ option CONFIG_XIP_ROM_SIZE=CONFIG_FAILOVER_SIZE
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Failover"
end
-#buildrom ./coreboot.rom ROM_SIZE "normal" "fallback" "failover"
-buildrom ./coreboot.rom ROM_SIZE "fallback" "failover"
+#buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback" "failover"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback" "failover"
mainboard VENDOR/MAINBOARD
option CC="CROSSCC"
-option CROSS_COMPILE="CROSS_PREFIX"
-option HOSTCC="CROSS_HOSTCC"
+option CONFIG_CROSS_COMPILE="CROSS_PREFIX"
+option CONFIG_HOSTCC="CROSS_HOSTCC"
__COMPRESSION__
__LOGLEVEL__
-option ROM_SIZE=512*1024
+option CONFIG_ROM_SIZE=512*1024
romimage "normal"
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=0x20000
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
option COREBOOT_EXTRA_VERSION=".0-normal"
payload __PAYLOAD__
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x20000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
option COREBOOT_EXTRA_VERSION=".0-fallback"
payload __PAYLOAD__
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
target hdama
-uses ARCH
+uses CONFIG_ARCH
uses CONFIG_COMPRESS
uses CONFIG_IOAPIC
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_UDELAY_TSC
uses CPU_FIXUP
-uses FALLBACK_SIZE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_MP_TABLE
-uses HAVE_PIRQ_TABLE
-uses HAVE_HARD_RESET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_HAVE_HARD_RESET
uses i586
uses i686
-uses INTEL_PPRO_MTRR
-uses HEAP_SIZE
-uses IRQ_SLOT_COUNT
+uses CONFIG_INTEL_PPRO_MTRR
+uses CONFIG_HEAP_SIZE
+uses CONFIG_IRQ_SLOT_COUNT
uses k7
uses k8
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
uses CONFIG_SMP
uses CONFIG_MAX_CPUS
-uses MEMORY_HOLE
-uses PAYLOAD_SIZE
-uses _RAMBASE
-uses _ROMBASE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_OFFSET
-uses ROM_SECTION_SIZE
-uses ROM_SIZE
-uses STACK_SIZE
-uses USE_FALLBACK_IMAGE
-uses USE_OPTION_TABLE
-uses HAVE_OPTION_TABLE
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MEMORY_HOLE
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_RAMBASE
+uses CONFIG_ROMBASE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_STACK_SIZE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
uses CONFIG_CONSOLE_SERIAL8250
-uses MAINBOARD
+uses CONFIG_MAINBOARD
uses CONFIG_CHIP_CONFIGURE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
uses COREBOOT_EXTRA_VERSION
option CONFIG_CHIP_CONFIGURE=1
-option MAXIMUM_CONSOLE_LOGLEVEL=8
-option DEFAULT_CONSOLE_LOGLEVEL=8
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
option CONFIG_CONSOLE_SERIAL8250=1
option CPU_FIXUP=1
option CONFIG_UDELAY_TSC=0
option i686=1
option i586=1
-option INTEL_PPRO_MTRR=1
+option CONFIG_INTEL_PPRO_MTRR=1
option k7=1
option k8=1
-option ROM_SIZE=1024*1024
+option CONFIG_ROM_SIZE=1024*1024
-option HAVE_OPTION_TABLE=1
+option CONFIG_HAVE_OPTION_TABLE=1
option CONFIG_ROM_PAYLOAD=1
-option HAVE_FALLBACK_BOOT=1
+option CONFIG_HAVE_FALLBACK_BOOT=1
###
### Compute the location and size of where this firmware image
### (coreboot plus bootloader) will live in the boot rom chip.
###
-option FALLBACK_SIZE=ROM_SIZE
+option CONFIG_FALLBACK_SIZE=CONFIG_ROM_SIZE
## Coreboot C code runs at this location in RAM
-option _RAMBASE=0x00004000
+option CONFIG_RAMBASE=0x00004000
#
###
#
# Arima hdama
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x10000
-# option ROM_SECTION_SIZE=0x100000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x10000
+# option CONFIG_ROM_SECTION_SIZE=0x100000
option COREBOOT_EXTRA_VERSION=".0Fallback"
mainboard arima/hdama
# payload ../../../../tg3--ide_disk.zelf
# payload /usr/share/etherboot/5.1.9pre2-lnxi-lb/tg3--ide_disk.zelf
end
-buildrom ./coreboot.rom ROM_SIZE "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback"
target hdama
mainboard arima/hdama
-option ROM_SIZE=512*1024-36*1024
+option CONFIG_ROM_SIZE=512*1024-36*1024
# Arima hdama
romimage "normal"
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=0x20000
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
option COREBOOT_EXTRA_VERSION=".0Normal"
payload ../../../payloads/filo.elf
# payload /etc/hosts
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x20000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
option COREBOOT_EXTRA_VERSION=".0Fallback"
payload ../../../payloads/filo.elf
# payload /etc/hosts
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
option CONFIG_COMPRESSED_PAYLOAD_NRV2B=0
option CONFIG_COMPRESSED_PAYLOAD_LZMA=0
-## ROM_SIZE is the total number of bytes allocated for coreboot use
+## CONFIG_ROM_SIZE is the total number of bytes allocated for coreboot use
## (normal AND fallback images and payloads).
## leave 36k for vsa and 32K for video ROM
-#option ROM_SIZE = 1024*256 - 36*1024 - 32 * 1024
+#option CONFIG_ROM_SIZE = 1024*256 - 36*1024 - 32 * 1024
#No VGA for now
-option ROM_SIZE = 1024*512 - 36*1024
+option CONFIG_ROM_SIZE = 1024*512 - 36*1024
-# ROM_IMAGE_SIZE is the maximum number of bytes allowed for a coreboot image,
+# CONFIG_ROM_IMAGE_SIZE is the maximum number of bytes allowed for a coreboot image,
## not including any payload.
-option ROM_IMAGE_SIZE=64*1024
+option CONFIG_ROM_IMAGE_SIZE=64*1024
-option FALLBACK_SIZE = ROM_SIZE
+option CONFIG_FALLBACK_SIZE = CONFIG_ROM_SIZE
-option DEFAULT_CONSOLE_LOGLEVEL = 9
-option MAXIMUM_CONSOLE_LOGLEVEL = 9
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=1
option COREBOOT_EXTRA_VERSION=".0Fallback"
payload ../payload.elf
end
-buildrom ./coreboot.rom ROM_SIZE "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback"
target mb_5blgp
mainboard asi/mb_5blgp
-option ROM_SIZE = 256 * 1024
+option CONFIG_ROM_SIZE = 256 * 1024
-option MAINBOARD_VENDOR = "ASI"
-option MAINBOARD_PART_NUMBER = "MB-5BLGP"
+option CONFIG_MAINBOARD_VENDOR = "ASI"
+option CONFIG_MAINBOARD_PART_NUMBER = "MB-5BLGP"
-option IRQ_SLOT_COUNT = 3
+option CONFIG_IRQ_SLOT_COUNT = 3
## Enable VGA with a splash screen (only 640x480 to run on most monitors).
## We want to support up to 1024x768@16 so we need 2MiB video memory.
option CONFIG_SPLASH_GRAPHIC = 1
option CONFIG_VIDEO_MB = 2
-option DEFAULT_CONSOLE_LOGLEVEL = 9
-option MAXIMUM_CONSOLE_LOGLEVEL = 9
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
romimage "normal"
- option USE_FALLBACK_IMAGE = 0
+ option CONFIG_USE_FALLBACK_IMAGE = 0
option COREBOOT_EXTRA_VERSION = ".0Normal"
payload ../payload.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE = 1
+ option CONFIG_USE_FALLBACK_IMAGE = 1
option COREBOOT_EXTRA_VERSION = ".0Fallback"
payload ../payload.elf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
target mb_5blmp
mainboard asi/mb_5blmp
-option ROM_SIZE = (256 * 1024)
-# option ROM_SIZE = (256 * 1024) - (32 * 1024)
-# option FALLBACK_SIZE = (256 * 1024) - (32 * 1024)
+option CONFIG_ROM_SIZE = (256 * 1024)
+# option CONFIG_ROM_SIZE = (256 * 1024) - (32 * 1024)
+# option CONFIG_FALLBACK_SIZE = (256 * 1024) - (32 * 1024)
romimage "normal"
- option USE_FALLBACK_IMAGE = 0
- option ROM_IMAGE_SIZE = 64 * 1024
+ option CONFIG_USE_FALLBACK_IMAGE = 0
+ option CONFIG_ROM_IMAGE_SIZE = 64 * 1024
option COREBOOT_EXTRA_VERSION = ".0Normal"
payload /tmp/filo.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE = 1
- option ROM_IMAGE_SIZE = 64 * 1024
+ option CONFIG_USE_FALLBACK_IMAGE = 1
+ option CONFIG_ROM_IMAGE_SIZE = 64 * 1024
option COREBOOT_EXTRA_VERSION = ".0Fallback"
payload /tmp/filo.elf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
-# buildrom ./coreboot.rom ROM_SIZE "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
+# buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback"
mainboard VENDOR/MAINBOARD
option CC="CROSSCC"
-option CROSS_COMPILE="CROSS_PREFIX"
-option HOSTCC="CROSS_HOSTCC"
+option CONFIG_CROSS_COMPILE="CROSS_PREFIX"
+option CONFIG_HOSTCC="CROSS_HOSTCC"
__COMPRESSION__
__LOGLEVEL__
romimage "normal"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=0x20000
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
option COREBOOT_EXTRA_VERSION=".0-normal"
payload __PAYLOAD__
end
romimage "fallback"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x20000
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
option COREBOOT_EXTRA_VERSION=".0-fallback"
payload __PAYLOAD__
end
romimage "failover"
- option USE_FAILOVER_IMAGE=1
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=FAILOVER_SIZE
- option XIP_ROM_SIZE=FAILOVER_SIZE
+ option CONFIG_USE_FAILOVER_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=CONFIG_FAILOVER_SIZE
+ option CONFIG_XIP_ROM_SIZE=CONFIG_FAILOVER_SIZE
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback" "failover"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback" "failover"
mainboard asus/a8n_e
romimage "normal"
- option USE_FAILOVER_IMAGE = 0
- option USE_FALLBACK_IMAGE = 0
- option ROM_IMAGE_SIZE = 128 * 1024
- option XIP_ROM_SIZE = 128 * 1024
+ option CONFIG_USE_FAILOVER_IMAGE = 0
+ option CONFIG_USE_FALLBACK_IMAGE = 0
+ option CONFIG_ROM_IMAGE_SIZE = 128 * 1024
+ option CONFIG_XIP_ROM_SIZE = 128 * 1024
option COREBOOT_EXTRA_VERSION = "_Normal"
payload ../payload.elf
end
romimage "fallback"
- option USE_FAILOVER_IMAGE = 0
- option USE_FALLBACK_IMAGE = 1
- option ROM_IMAGE_SIZE = 128 * 1024
- option XIP_ROM_SIZE = 128 * 1024
+ option CONFIG_USE_FAILOVER_IMAGE = 0
+ option CONFIG_USE_FALLBACK_IMAGE = 1
+ option CONFIG_ROM_IMAGE_SIZE = 128 * 1024
+ option CONFIG_XIP_ROM_SIZE = 128 * 1024
option COREBOOT_EXTRA_VERSION = "_Fallback"
payload ../payload.elf
end
romimage "failover"
- option USE_FAILOVER_IMAGE = 1
- option USE_FALLBACK_IMAGE = 0
- option ROM_IMAGE_SIZE = FAILOVER_SIZE
- option XIP_ROM_SIZE = FAILOVER_SIZE
+ option CONFIG_USE_FAILOVER_IMAGE = 1
+ option CONFIG_USE_FALLBACK_IMAGE = 0
+ option CONFIG_ROM_IMAGE_SIZE = CONFIG_FAILOVER_SIZE
+ option CONFIG_XIP_ROM_SIZE = CONFIG_FAILOVER_SIZE
option COREBOOT_EXTRA_VERSION = "_Failover"
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback" "failover"
-# buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback" "failover"
+# buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
mainboard asus/a8v-e_se
romimage "normal"
- option ROM_SIZE = 512 * 1024
- option USE_FALLBACK_IMAGE = 0
- option ROM_IMAGE_SIZE = 128 * 1024
+ option CONFIG_ROM_SIZE = 512 * 1024
+ option CONFIG_USE_FALLBACK_IMAGE = 0
+ option CONFIG_ROM_IMAGE_SIZE = 128 * 1024
option COREBOOT_EXTRA_VERSION=".0Normal"
payload ../payload.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE = 1
- option ROM_IMAGE_SIZE = 128 * 1024
+ option CONFIG_USE_FALLBACK_IMAGE = 1
+ option CONFIG_ROM_IMAGE_SIZE = 128 * 1024
option COREBOOT_EXTRA_VERSION=".0Fallback"
payload ../payload.elf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
mainboard asus/m2v-mx_se
option CC="CROSSCC"
-option CROSS_COMPILE="CROSS_PREFIX"
-option HOSTCC="CROSS_HOSTCC"
+option CONFIG_CROSS_COMPILE="CROSS_PREFIX"
+option CONFIG_HOSTCC="CROSS_HOSTCC"
-## ROM_SIZE is the total number of bytes allocated for coreboot use
+## CONFIG_ROM_SIZE is the total number of bytes allocated for coreboot use
## (normal AND fallback images and payloads).
# The board comes with 512KB SPI flash (DIP8), 128KB is for coreboot binary
# 384KB of flash is for payload/roms.
-option ROM_SIZE = 512 * 1024
+option CONFIG_ROM_SIZE = 512 * 1024
-## ROM_IMAGE_SIZE is the maximum number of bytes allowed for a coreboot image,
+## CONFIG_ROM_IMAGE_SIZE is the maximum number of bytes allowed for a coreboot image,
## not including any payload.
# Please note that 128KB is cached for (XIP) too
-option ROM_IMAGE_SIZE = 128 * 1024
+option CONFIG_ROM_IMAGE_SIZE = 128 * 1024
-## FALLBACK_SIZE is the amount of the ROM the complete fallback image
+## CONFIG_FALLBACK_SIZE is the amount of the ROM the complete fallback image
## (including payload) will use.
-option FALLBACK_SIZE = ROM_SIZE
+option CONFIG_FALLBACK_SIZE = CONFIG_ROM_SIZE
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=1
payload __PAYLOAD__
end
-buildrom ./coreboot.rom ROM_SIZE "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback"
target asus_m2v-mx_se
mainboard asus/m2v-mx_se
-## ROM_SIZE is the total number of bytes allocated for coreboot use
+## CONFIG_ROM_SIZE is the total number of bytes allocated for coreboot use
## (normal AND fallback images and payloads).
# The board comes with 512KB SPI flash (DIP8), 128KB is for coreboot binary
# 384KB of flash is for payload/roms.
-option ROM_SIZE = 512 * 1024
+option CONFIG_ROM_SIZE = 512 * 1024
# Use following line instead if you want to use onboard VGA -
# padd the rom size to 64KB or XIP won't work, complaining about
# not good base.
-#option ROM_SIZE = (512 * 1024) - (64 * 1024)
+#option CONFIG_ROM_SIZE = (512 * 1024) - (64 * 1024)
-## ROM_IMAGE_SIZE is the maximum number of bytes allowed for a coreboot image,
+## CONFIG_ROM_IMAGE_SIZE is the maximum number of bytes allowed for a coreboot image,
## not including any payload.
# Please note that 128KB is cached for (XIP) too
-option ROM_IMAGE_SIZE = 128 * 1024
+option CONFIG_ROM_IMAGE_SIZE = 128 * 1024
-## FALLBACK_SIZE is the amount of the ROM the complete fallback image
+## CONFIG_FALLBACK_SIZE is the amount of the ROM the complete fallback image
## (including payload) will use.
-option FALLBACK_SIZE = ROM_SIZE
+option CONFIG_FALLBACK_SIZE = CONFIG_ROM_SIZE
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=1
payload ../payload.elf
end
-buildrom ./coreboot.rom ROM_SIZE "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback"
target mew-am
mainboard asus/mew-am
-option ROM_SIZE = 512 * 1024
+option CONFIG_ROM_SIZE = 512 * 1024
-option MAINBOARD_VENDOR = "ASUS"
-option MAINBOARD_PART_NUMBER = "MEW-AM"
+option CONFIG_MAINBOARD_VENDOR = "ASUS"
+option CONFIG_MAINBOARD_PART_NUMBER = "MEW-AM"
-option IRQ_SLOT_COUNT = 8
+option CONFIG_IRQ_SLOT_COUNT = 8
-option DEFAULT_CONSOLE_LOGLEVEL = 9
-option MAXIMUM_CONSOLE_LOGLEVEL = 9
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
option CONFIG_CONSOLE_VGA = 1
option CONFIG_PCI_ROM_RUN = 1
romimage "normal"
- option USE_FALLBACK_IMAGE = 0
+ option CONFIG_USE_FALLBACK_IMAGE = 0
option COREBOOT_EXTRA_VERSION = ".0Normal"
payload /tmp/filo.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE = 1
+ option CONFIG_USE_FALLBACK_IMAGE = 1
option COREBOOT_EXTRA_VERSION = ".0Fallback"
payload /tmp/filo.elf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
mainboard asus/mew-vm
## Without VGA BIOS
-option ROM_SIZE = 512 * 1024
+option CONFIG_ROM_SIZE = 512 * 1024
## With VGA BIOS (32k)
-#option ROM_SIZE = (512 * 1024) - (32 * 1024)
+#option CONFIG_ROM_SIZE = (512 * 1024) - (32 * 1024)
romimage "normal"
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=0x10000
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=0x10000
option COREBOOT_EXTRA_VERSION=".0Normal"
# payload /etc/hosts
payload /home/amp/filo-0.5/filo.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x10000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x10000
option COREBOOT_EXTRA_VERSION=".0Fallback"
# payload /etc/hosts
payload /home/amp/filo-0.5/filo.elf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
target p2b-d
mainboard asus/p2b-d
-option ROM_SIZE = 256 * 1024
+option CONFIG_ROM_SIZE = 256 * 1024
-option MAINBOARD_VENDOR = "ASUS"
-option MAINBOARD_PART_NUMBER = "P2B-D"
+option CONFIG_MAINBOARD_VENDOR = "ASUS"
+option CONFIG_MAINBOARD_PART_NUMBER = "P2B-D"
-option IRQ_SLOT_COUNT = 6
+option CONFIG_IRQ_SLOT_COUNT = 6
-option DEFAULT_CONSOLE_LOGLEVEL = 9
-option MAXIMUM_CONSOLE_LOGLEVEL = 9
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
option CONFIG_CONSOLE_VGA = 1
option CONFIG_PCI_ROM_RUN = 1
romimage "normal"
- option USE_FALLBACK_IMAGE = 0
+ option CONFIG_USE_FALLBACK_IMAGE = 0
option COREBOOT_EXTRA_VERSION = ".0Normal"
payload ../payload.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE = 1
+ option CONFIG_USE_FALLBACK_IMAGE = 1
option COREBOOT_EXTRA_VERSION = ".0Fallback"
payload ../payload.elf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
target p2b-ds
mainboard asus/p2b-ds
-option ROM_SIZE = 256 * 1024
+option CONFIG_ROM_SIZE = 256 * 1024
-option MAINBOARD_VENDOR = "ASUS"
-option MAINBOARD_PART_NUMBER = "P2B-DS"
+option CONFIG_MAINBOARD_VENDOR = "ASUS"
+option CONFIG_MAINBOARD_PART_NUMBER = "P2B-DS"
-option IRQ_SLOT_COUNT = 7
+option CONFIG_IRQ_SLOT_COUNT = 7
-option DEFAULT_CONSOLE_LOGLEVEL = 9
-option MAXIMUM_CONSOLE_LOGLEVEL = 9
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
option CONFIG_CONSOLE_VGA = 1
option CONFIG_PCI_ROM_RUN = 1
romimage "normal"
- option USE_FALLBACK_IMAGE = 0
+ option CONFIG_USE_FALLBACK_IMAGE = 0
option COREBOOT_EXTRA_VERSION = ".0Normal"
payload ../payload.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE = 1
+ option CONFIG_USE_FALLBACK_IMAGE = 1
option COREBOOT_EXTRA_VERSION = ".0Fallback"
payload ../payload.elf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
target p2b-f
mainboard asus/p2b-f
-option ROM_SIZE = 256 * 1024
+option CONFIG_ROM_SIZE = 256 * 1024
-option MAINBOARD_VENDOR = "ASUS"
-option MAINBOARD_PART_NUMBER = "P2B-F"
+option CONFIG_MAINBOARD_VENDOR = "ASUS"
+option CONFIG_MAINBOARD_PART_NUMBER = "P2B-F"
-option IRQ_SLOT_COUNT = 7
+option CONFIG_IRQ_SLOT_COUNT = 7
-option DEFAULT_CONSOLE_LOGLEVEL = 9
-option MAXIMUM_CONSOLE_LOGLEVEL = 9
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
option CONFIG_CONSOLE_VGA = 1
option CONFIG_PCI_ROM_RUN = 1
romimage "normal"
- option USE_FALLBACK_IMAGE = 0
+ option CONFIG_USE_FALLBACK_IMAGE = 0
option COREBOOT_EXTRA_VERSION = ".0Normal"
payload /tmp/filo.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE = 1
+ option CONFIG_USE_FALLBACK_IMAGE = 1
option COREBOOT_EXTRA_VERSION = ".0Fallback"
payload /tmp/filo.elf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
target p2b
mainboard asus/p2b
-option ROM_SIZE = 256 * 1024
+option CONFIG_ROM_SIZE = 256 * 1024
-option MAINBOARD_VENDOR = "ASUS"
-option MAINBOARD_PART_NUMBER = "P2B"
+option CONFIG_MAINBOARD_VENDOR = "ASUS"
+option CONFIG_MAINBOARD_PART_NUMBER = "P2B"
-option IRQ_SLOT_COUNT = 6
+option CONFIG_IRQ_SLOT_COUNT = 6
-option DEFAULT_CONSOLE_LOGLEVEL = 9
-option MAXIMUM_CONSOLE_LOGLEVEL = 9
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
option CONFIG_CONSOLE_VGA = 1
option CONFIG_PCI_ROM_RUN = 1
romimage "normal"
- option USE_FALLBACK_IMAGE = 0
+ option CONFIG_USE_FALLBACK_IMAGE = 0
option COREBOOT_EXTRA_VERSION = ".0Normal"
payload /tmp/filo.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE = 1
+ option CONFIG_USE_FALLBACK_IMAGE = 1
option COREBOOT_EXTRA_VERSION = ".0Fallback"
payload /tmp/filo.elf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
target p3b-f
mainboard asus/p3b-f
-option ROM_SIZE = 256 * 1024
+option CONFIG_ROM_SIZE = 256 * 1024
-option MAINBOARD_VENDOR = "ASUS"
-option MAINBOARD_PART_NUMBER = "P3B-F"
+option CONFIG_MAINBOARD_VENDOR = "ASUS"
+option CONFIG_MAINBOARD_PART_NUMBER = "P3B-F"
-option IRQ_SLOT_COUNT = 8
+option CONFIG_IRQ_SLOT_COUNT = 8
-option DEFAULT_CONSOLE_LOGLEVEL = 9
-option MAXIMUM_CONSOLE_LOGLEVEL = 9
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
option CONFIG_CONSOLE_VGA = 1
option CONFIG_PCI_ROM_RUN = 1
romimage "normal"
- option USE_FALLBACK_IMAGE = 0
+ option CONFIG_USE_FALLBACK_IMAGE = 0
option COREBOOT_EXTRA_VERSION = ".0Normal"
payload /tmp/filo.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE = 1
+ option CONFIG_USE_FALLBACK_IMAGE = 1
option COREBOOT_EXTRA_VERSION = ".0Fallback"
payload /tmp/filo.elf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
target tc320
mainboard axus/tc320
-option ROM_SIZE = 256 * 1024
+option CONFIG_ROM_SIZE = 256 * 1024
## Enable VGA with a splash screen (only 640x480 to run on most monitors).
## We want to support up to 1024x768@16 so we need 2MiB video memory.
option CONFIG_SPLASH_GRAPHIC = 1
option CONFIG_VIDEO_MB = 2
-option DEFAULT_CONSOLE_LOGLEVEL = 6
-option MAXIMUM_CONSOLE_LOGLEVEL = 6
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 6
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 6
romimage "normal"
- option USE_FALLBACK_IMAGE = 0
+ option CONFIG_USE_FALLBACK_IMAGE = 0
option COREBOOT_EXTRA_VERSION = ".0Normal"
payload ../../../../../../../images/etherboot.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE = 1
+ option CONFIG_USE_FALLBACK_IMAGE = 1
option COREBOOT_EXTRA_VERSION = ".0Fallback"
payload ../../../../../../../images/etherboot.elf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
target pt-6ibd
mainboard azza/pt-6ibd
-option ROM_SIZE = 256 * 1024
+option CONFIG_ROM_SIZE = 256 * 1024
-option MAINBOARD_VENDOR = "AZZA"
-option MAINBOARD_PART_NUMBER = "PT-6IBD"
+option CONFIG_MAINBOARD_VENDOR = "AZZA"
+option CONFIG_MAINBOARD_PART_NUMBER = "PT-6IBD"
-option IRQ_SLOT_COUNT = 7
+option CONFIG_IRQ_SLOT_COUNT = 7
-option DEFAULT_CONSOLE_LOGLEVEL = 9
-option MAXIMUM_CONSOLE_LOGLEVEL = 9
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
option CONFIG_CONSOLE_VGA = 1
option CONFIG_PCI_ROM_RUN = 1
romimage "normal"
- option USE_FALLBACK_IMAGE = 0
+ option CONFIG_USE_FALLBACK_IMAGE = 0
option COREBOOT_EXTRA_VERSION = ".0Normal"
payload /tmp/filo.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE = 1
+ option CONFIG_USE_FALLBACK_IMAGE = 1
option COREBOOT_EXTRA_VERSION = ".0Fallback"
payload /tmp/filo.elf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
target winnet100
mainboard bcom/winnet100
-option ROM_SIZE = 256 * 1024
+option CONFIG_ROM_SIZE = 256 * 1024
## Enable VGA with a splash screen (only 640x480 to run on most monitors).
## We want to support up to 1024x768@16 so we need 2MiB video memory.
option CONFIG_SPLASH_GRAPHIC = 1
option CONFIG_VIDEO_MB = 2
-option DEFAULT_CONSOLE_LOGLEVEL = 6
-option MAXIMUM_CONSOLE_LOGLEVEL = 6
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 6
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 6
romimage "normal"
- option USE_FALLBACK_IMAGE = 0
- option ROM_IMAGE_SIZE = 64 * 1024
+ option CONFIG_USE_FALLBACK_IMAGE = 0
+ option CONFIG_ROM_IMAGE_SIZE = 64 * 1024
option COREBOOT_EXTRA_VERSION = ".0Normal"
payload ../../../../../../../images/etherboot.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE = 1
- option ROM_IMAGE_SIZE = 64 * 1024
+ option CONFIG_USE_FALLBACK_IMAGE = 1
+ option CONFIG_ROM_IMAGE_SIZE = 64 * 1024
option COREBOOT_EXTRA_VERSION = ".0Fallback"
payload ../../../../../../../images/etherboot.elf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
mainboard VENDOR/MAINBOARD
option CC="CROSSCC"
-option CROSS_COMPILE="CROSS_PREFIX"
-option HOSTCC="CROSS_HOSTCC"
+option CONFIG_CROSS_COMPILE="CROSS_PREFIX"
+option CONFIG_HOSTCC="CROSS_HOSTCC"
__COMPRESSION__
__LOGLEVEL__
-option ROM_SIZE=512*1024
+option CONFIG_ROM_SIZE=512*1024
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x20000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
option COREBOOT_EXTRA_VERSION=".0-fallback"
payload __PAYLOAD__
end
-buildrom ./coreboot.rom ROM_SIZE "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback"
target bcom-winnet-p680
mainboard bcom/winnetp680
-option MAXIMUM_CONSOLE_LOGLEVEL=8
-option DEFAULT_CONSOLE_LOGLEVEL=8
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
option CONFIG_CONSOLE_SERIAL8250=1
# coreboot C code runs at this location in RAM
-option _RAMBASE=0x00004000
+option CONFIG_RAMBASE=0x00004000
#
# If space is allotted for a VGA BIOS,
# generate the final ROM like this:
# cat vgabios bochsbios coreboot.rom > coreboot.rom.final
#
-#option ROM_SIZE = (512 * 1024) - (63 * 1024) - (64 * 1024)
-option ROM_SIZE = (512 * 1024)
+#option CONFIG_ROM_SIZE = (512 * 1024) - (63 * 1024) - (64 * 1024)
+option CONFIG_ROM_SIZE = (512 * 1024)
romimage "image"
option COREBOOT_EXTRA_VERSION = "-winnetp680"
payload ../payload.elf
end
-buildrom ./coreboot.rom ROM_SIZE "image"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "image"
mainboard biostar/m6tba
# Note: The original flash ROM chip is 128 KB.
-option ROM_SIZE = 256 * 1024
+option CONFIG_ROM_SIZE = 256 * 1024
-option MAINBOARD_VENDOR = "Biostar"
-option MAINBOARD_PART_NUMBER = "M6TBA"
+option CONFIG_MAINBOARD_VENDOR = "Biostar"
+option CONFIG_MAINBOARD_PART_NUMBER = "M6TBA"
-option IRQ_SLOT_COUNT = 7
+option CONFIG_IRQ_SLOT_COUNT = 7
-option DEFAULT_CONSOLE_LOGLEVEL = 9
-option MAXIMUM_CONSOLE_LOGLEVEL = 9
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
option CONFIG_CONSOLE_VGA = 1
option CONFIG_PCI_ROM_RUN = 1
romimage "normal"
- option USE_FALLBACK_IMAGE = 0
+ option CONFIG_USE_FALLBACK_IMAGE = 0
option COREBOOT_EXTRA_VERSION = ".0Normal"
payload /tmp/filo.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE = 1
+ option CONFIG_USE_FALLBACK_IMAGE = 1
option COREBOOT_EXTRA_VERSION = ".0Fallback"
payload /tmp/filo.elf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
romimage "normal"
# 48K for ATI rom
- option ROM_SIZE = 512*1024-48*1024
+ option CONFIG_ROM_SIZE = 512*1024-48*1024
# 48K for SCSI FW and 48K for ATI ROM
-# option ROM_SIZE = 512*1024-48*1024-48*1024
+# option CONFIG_ROM_SIZE = 512*1024-48*1024-48*1024
# 64K for Etherboot
-# option ROM_SIZE = 512*1024-64*1024
- option USE_FALLBACK_IMAGE=0
-# option ROM_IMAGE_SIZE=0x13800
-# option ROM_IMAGE_SIZE=0x17800
-# option ROM_IMAGE_SIZE=0x15000
- option ROM_IMAGE_SIZE=0x20000
- option XIP_ROM_SIZE=0x20000
+# option CONFIG_ROM_SIZE = 512*1024-64*1024
+ option CONFIG_USE_FALLBACK_IMAGE=0
+# option CONFIG_ROM_IMAGE_SIZE=0x13800
+# option CONFIG_ROM_IMAGE_SIZE=0x17800
+# option CONFIG_ROM_IMAGE_SIZE=0x15000
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+ option CONFIG_XIP_ROM_SIZE=0x20000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Normal"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
-# option ROM_IMAGE_SIZE=0x13800
-# option ROM_IMAGE_SIZE=0x17800
-# option ROM_IMAGE_SIZE=0x15000
- option ROM_IMAGE_SIZE=0x20000
- option XIP_ROM_SIZE=0x20000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+# option CONFIG_ROM_IMAGE_SIZE=0x13800
+# option CONFIG_ROM_IMAGE_SIZE=0x17800
+# option CONFIG_ROM_IMAGE_SIZE=0x15000
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+ option CONFIG_XIP_ROM_SIZE=0x20000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
# payload ../../../payloads/tg3--eepro100--e1000--filo_hda2_com2.zelf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
target deskpro_en_sff_p600
mainboard compaq/deskpro_en_sff_p600
-option ROM_SIZE = 256 * 1024
+option CONFIG_ROM_SIZE = 256 * 1024
-option MAINBOARD_VENDOR = "Compaq"
-option MAINBOARD_PART_NUMBER = "Deskpro EN SFF P600"
+option CONFIG_MAINBOARD_VENDOR = "Compaq"
+option CONFIG_MAINBOARD_PART_NUMBER = "Deskpro EN SFF P600"
-option IRQ_SLOT_COUNT = 5
+option CONFIG_IRQ_SLOT_COUNT = 5
-option DEFAULT_CONSOLE_LOGLEVEL = 9
-option MAXIMUM_CONSOLE_LOGLEVEL = 9
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
option CONFIG_CONSOLE_VGA = 1
option CONFIG_PCI_ROM_RUN = 1
romimage "normal"
- option USE_FALLBACK_IMAGE = 0
+ option CONFIG_USE_FALLBACK_IMAGE = 0
option COREBOOT_EXTRA_VERSION = ".0Normal"
payload /tmp/filo.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE = 1
+ option CONFIG_USE_FALLBACK_IMAGE = 1
option COREBOOT_EXTRA_VERSION = ".0Fallback"
payload /tmp/filo.elf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
target s1850
mainboard dell/s1850
-option ROM_SIZE=1024*1024
-option MAXIMUM_CONSOLE_LOGLEVEL=9
-option DEFAULT_CONSOLE_LOGLEVEL=9
+option CONFIG_ROM_SIZE=1024*1024
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=9
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL=9
romimage "normal"
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=0x16000
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=0x16000
option COREBOOT_EXTRA_VERSION=".0Normal"
# payload ../../../payloads/filo.elf
payload /tmp/filo.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x16000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x16000
option COREBOOT_EXTRA_VERSION=".0Fallback"
# payload ../../../payloads/filo.elf
payload /tmp/filo.elf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
target adl855pc
mainboard digitallogic/adl855pc
-option DEFAULT_CONSOLE_LOGLEVEL=9
-option MAXIMUM_CONSOLE_LOGLEVEL=9
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL=9
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=9
romimage "normal"
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=0x10000
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=0x10000
option COREBOOT_EXTRA_VERSION=".0Normal"
payload /etc/hosts
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x10000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x10000
option COREBOOT_EXTRA_VERSION=".0Fallback"
payload /etc/hosts
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
mainboard VENDOR/MAINBOARD
option CC="CROSSCC"
-option CROSS_COMPILE="CROSS_PREFIX"
-option HOSTCC="CROSS_HOSTCC"
+option CONFIG_CROSS_COMPILE="CROSS_PREFIX"
+option CONFIG_HOSTCC="CROSS_HOSTCC"
__COMPRESSION__
__LOGLEVEL__
romimage "fallback"
- option FALLBACK_SIZE = 256 * 1024
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE= 128 * 1024
+ option CONFIG_FALLBACK_SIZE = 256 * 1024
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE= 128 * 1024
option COREBOOT_EXTRA_VERSION=".0Fallback"
payload __PAYLOAD__
end
-buildrom ./coreboot.rom ROM_SIZE "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback"
-option DEFAULT_CONSOLE_LOGLEVEL=3
-option MAXIMUM_CONSOLE_LOGLEVEL=3
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL=3
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=3
option CONFIG_COMPRESS=0
option CONFIG_CONSOLE_VGA=0
#romimage "normal"
-# option USE_FALLBACK_IMAGE=0
-# option ROM_IMAGE_SIZE=0x10000
+# option CONFIG_USE_FALLBACK_IMAGE=0
+# option CONFIG_ROM_IMAGE_SIZE=0x10000
# option COREBOOT_EXTRA_VERSION=".0Normal"
# payload /etc/hosts
#end
romimage "fallback"
- option FALLBACK_SIZE = 256 * 1024
-# option ROM_SIZE=512*1024
-# option ROM_SECTION_SIZE=512*1024
- option USE_FALLBACK_IMAGE=1
-# option ROM_IMAGE_SIZE=32 * 1024 # 0x8000
- option ROM_IMAGE_SIZE=128 * 1024 # 0x10000
-# option ROM_IMAGE_SIZE=512 * 1024 # 0x10000
+ option CONFIG_FALLBACK_SIZE = 256 * 1024
+# option CONFIG_ROM_SIZE=512*1024
+# option CONFIG_ROM_SECTION_SIZE=512*1024
+ option CONFIG_USE_FALLBACK_IMAGE=1
+# option CONFIG_ROM_IMAGE_SIZE=32 * 1024 # 0x8000
+ option CONFIG_ROM_IMAGE_SIZE=128 * 1024 # 0x10000
+# option CONFIG_ROM_IMAGE_SIZE=512 * 1024 # 0x10000
option COREBOOT_EXTRA_VERSION=".0Fallback"
payload ../../filo.elf
# payload ../../eepro100--ide_disk.zelf
end
-buildrom ./coreboot.rom ROM_SIZE "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback"
option CONFIG_COMPRESSED_PAYLOAD_NRV2B=0
-## ROM_SIZE is the total number of bytes allocated for coreboot use
+## CONFIG_ROM_SIZE is the total number of bytes allocated for coreboot use
## (normal AND fallback images and payloads).
## leave 36k for vsa
##
-option ROM_SIZE = 1024*1024 - 36 * 1024
+option CONFIG_ROM_SIZE = 1024*1024 - 36 * 1024
-## ROM_IMAGE_SIZE is the maximum number of bytes allowed for a coreboot image,
+## CONFIG_ROM_IMAGE_SIZE is the maximum number of bytes allowed for a coreboot image,
## not including any payload.
-option ROM_IMAGE_SIZE=64*1024
+option CONFIG_ROM_IMAGE_SIZE=64*1024
-option FALLBACK_SIZE = ROM_SIZE
+option CONFIG_FALLBACK_SIZE = CONFIG_ROM_SIZE
-option DEFAULT_CONSOLE_LOGLEVEL = 9
-option MAXIMUM_CONSOLE_LOGLEVEL = 9
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=1
option COREBOOT_EXTRA_VERSION=".0Fallback"
payload ../payload.elf
end
-buildrom ./coreboot.rom ROM_SIZE "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback"
target 5bcm
mainboard eaglelion/5bcm
-option ROM_SIZE=256*1024
+option CONFIG_ROM_SIZE=256*1024
romimage "normal"
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=0x10000
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=0x10000
option COREBOOT_EXTRA_VERSION=".0Normal"
# payload /usr/share/etherboot/5.1.9pre2-lnxi-lb/tg3--ide_disk.zelf
# payload ../../../../tg3--ide_disk.zelf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x10000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x10000
option COREBOOT_EXTRA_VERSION=".0Fallback"
# payload /usr/share/etherboot/5.1.9pre2-lnxi-lb/tg3--ide_disk.zelf
# payload ../../../../tg3--ide_disk.zelf
payload /home/hamish/work/etherboot/eb-5.2.6-lne100.elf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
romimage "normal"
## Enable PPC405 instructions
- option CPU_OPT="-mcpu=405"
+ option CONFIG_CPU_OPT="-mcpu=405"
## use a cross compiler
- #option CROSS_COMPILE="powerpc-ibm-eabi-"
+ #option CONFIG_CROSS_COMPILE="powerpc-ibm-eabi-"
## Use stage 1 initialization code
option CONFIG_USE_INIT=1
option CONFIG_COMPRESS=0
## Turn off POST codes
- option NO_POST=1
+ option CONFIG_NO_POST=1
## Enable serial console
- option DEFAULT_CONSOLE_LOGLEVEL=8
+ option CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
option CONFIG_CONSOLE_SERIAL8250=1
# Divisor of 69 == 9600 baud due to weird clocking
- option TTYS0_DIV=69
- option TTYS0_BAUD=9600
+ option CONFIG_TTYS0_DIV=69
+ option CONFIG_TTYS0_BAUD=9600
## Boot linux from IDE
option CONFIG_IDE=1
option CONFIG_FS_EXT2=1
option CONFIG_FS_ISO9660=1
option CONFIG_FS_FAT=1
- option AUTOBOOT_CMDLINE="hda1:/vmlinuz"
+ option CONFIG_AUTOBOOT_CMDLINE="hda1:/vmlinuz"
- option ROM_SIZE=1024*1024
+ option CONFIG_ROM_SIZE=1024*1024
## Board has fixed size RAM
- option EMBEDDED_RAM_SIZE=64*1024*1024
+ option CONFIG_EMBEDDED_RAM_SIZE=64*1024*1024
## Coreboot C code runs at this location in RAM
- option _RAMBASE=0x00100000
+ option CONFIG_RAMBASE=0x00100000
##
## Use a 64K stack
##
- option STACK_SIZE=0x10000
+ option CONFIG_STACK_SIZE=0x10000
##
## Use a 64K heap
##
- option HEAP_SIZE=0x10000
+ option CONFIG_HEAP_SIZE=0x10000
##
## System clock
option CONFIG_SYS_CLK_FREQ=33
##
- option _ROMBASE=0xfff00000
+ option CONFIG_ROMBASE=0xfff00000
## Reset vector address
- option _RESET=0xfffffffc
+ option CONFIG_RESET=0xfffffffc
## Exception vectors
- option _EXCEPTION_VECTORS=_ROMBASE+0x100
+ option CONFIG_EXCEPTION_VECTORS=CONFIG_ROMBASE+0x100
## coreboot ROM start address
- option _ROMSTART=0xfff03000
+ option CONFIG_ROMSTART=0xfff03000
## coreboot C code runs at this location in RAM
- option _RAMBASE=0x00100000
+ option CONFIG_RAMBASE=0x00100000
end
-buildrom ./coreboot.rom ROM_SIZE "normal"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal"
mainboard VENDOR/MAINBOARD
option CC="CROSSCC"
-option CROSS_COMPILE="CROSS_PREFIX"
-option HOSTCC="CROSS_HOSTCC"
+option CONFIG_CROSS_COMPILE="CROSS_PREFIX"
+option CONFIG_HOSTCC="CROSS_HOSTCC"
__COMPRESSION__
__LOGLEVEL__
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=1
option COREBOOT_EXTRA_VERSION=".0"
payload __PAYLOAD__
end
-buildrom ./coreboot.rom ROM_SIZE "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback"
target qemu-x86-car
mainboard emulation/qemu-x86
-option USE_DCACHE_RAM=1
+option CONFIG_USE_DCACHE_RAM=1
option CONFIG_USE_INIT=1
-option ROM_SIZE=512*1024
+option CONFIG_ROM_SIZE=512*1024
option CONFIG_USE_INIT=1
option CONFIG_USE_PRINTK_IN_CAR=1
option CC="gcc -m32"
-option HAVE_PIRQ_TABLE=1
-option IRQ_SLOT_COUNT=6
+option CONFIG_HAVE_PIRQ_TABLE=1
+option CONFIG_IRQ_SLOT_COUNT=6
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x10000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x10000
option COREBOOT_EXTRA_VERSION="-GRUB2"
# payload /home/stepan/core.img
payload ../payload.elf
end
-buildrom ./coreboot.rom ROM_SIZE "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback"
target qemu-x86
mainboard emulation/qemu-x86
-option ROM_SIZE=2048*1024
+option CONFIG_ROM_SIZE=2048*1024
option CONFIG_COMPRESSED_PAYLOAD_LZMA=1
option CONFIG_PRECOMPRESSED_PAYLOAD=1
option CC="gcc -m32"
-option HAVE_PIRQ_TABLE=1
-option IRQ_SLOT_COUNT=6
+option CONFIG_HAVE_PIRQ_TABLE=1
+option CONFIG_IRQ_SLOT_COUNT=6
romimage "image"
option COREBOOT_EXTRA_VERSION="-LAB"
payload ../payload.elf.lzma
end
-buildrom ./coreboot.rom ROM_SIZE "image"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "image"
target qemu-x86-OLPC
mainboard emulation/qemu-x86
-option ROM_SIZE=1024*1024 - (128 * 1024)
+option CONFIG_ROM_SIZE=1024*1024 - (128 * 1024)
option CONFIG_COMPRESSED_PAYLOAD_LZMA=1
option CONFIG_PRECOMPRESSED_PAYLOAD=0
option CC="gcc -m32"
-option HAVE_PIRQ_TABLE=1
-option IRQ_SLOT_COUNT=6
+option CONFIG_HAVE_PIRQ_TABLE=1
+option CONFIG_IRQ_SLOT_COUNT=6
romimage "image"
option COREBOOT_EXTRA_VERSION="-OpenBIOS"
payload /tmp/olpcpayload.elf
end
-buildrom ./coreboot.rom ROM_SIZE "image"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "image"
target qemu-x86
mainboard emulation/qemu-x86
-option ROM_SIZE=512*1024
+option CONFIG_ROM_SIZE=512*1024
option CC="gcc -m32"
-option HAVE_PIRQ_TABLE=1
-option IRQ_SLOT_COUNT=6
-option DEFAULT_CONSOLE_LOGLEVEL=9
-option MAXIMUM_CONSOLE_LOGLEVEL=9
+option CONFIG_HAVE_PIRQ_TABLE=1
+option CONFIG_IRQ_SLOT_COUNT=6
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL=9
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=9
romimage "normal"
option COREBOOT_EXTRA_VERSION="-GRUB2"
payload ../payload.elf
end
-buildrom ./coreboot.rom ROM_SIZE "normal"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal"
target ga-6bxc
mainboard gigabyte/ga-6bxc
-option ROM_SIZE = 256 * 1024
+option CONFIG_ROM_SIZE = 256 * 1024
-option MAINBOARD_VENDOR = "GIGABYTE"
-option MAINBOARD_PART_NUMBER = "GA-6BXC"
+option CONFIG_MAINBOARD_VENDOR = "GIGABYTE"
+option CONFIG_MAINBOARD_PART_NUMBER = "GA-6BXC"
-option IRQ_SLOT_COUNT = 6
+option CONFIG_IRQ_SLOT_COUNT = 6
-option DEFAULT_CONSOLE_LOGLEVEL = 9
-option MAXIMUM_CONSOLE_LOGLEVEL = 9
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
option CONFIG_CONSOLE_VGA = 1
option CONFIG_PCI_ROM_RUN = 1
romimage "normal"
- option USE_FALLBACK_IMAGE = 0
+ option CONFIG_USE_FALLBACK_IMAGE = 0
option COREBOOT_EXTRA_VERSION = ".0Normal"
payload /tmp/filo.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE = 1
+ option CONFIG_USE_FALLBACK_IMAGE = 1
option COREBOOT_EXTRA_VERSION = ".0Fallback"
payload /tmp/filo.elf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
mainboard VENDOR/MAINBOARD
option CC="CROSSCC"
-option CROSS_COMPILE="CROSS_PREFIX"
-option HOSTCC="CROSS_HOSTCC"
+option CONFIG_CROSS_COMPILE="CROSS_PREFIX"
+option CONFIG_HOSTCC="CROSS_HOSTCC"
__COMPRESSION__
__LOGLEVEL__
-option ROM_SIZE = 512*1024
+option CONFIG_ROM_SIZE = 512*1024
romimage "normal"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=0x28000
- option XIP_ROM_SIZE=0x40000
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=0x28000
+ option CONFIG_XIP_ROM_SIZE=0x40000
option COREBOOT_EXTRA_VERSION=".0-Normal"
payload __PAYLOAD__
end
romimage "fallback"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x20000
- option XIP_ROM_SIZE=0x40000
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+ option CONFIG_XIP_ROM_SIZE=0x40000
option COREBOOT_EXTRA_VERSION=".0-Fallback"
payload __PAYLOAD__
end
romimage "failover"
- option USE_FAILOVER_IMAGE=1
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=FAILOVER_SIZE
- option XIP_ROM_SIZE=FAILOVER_SIZE
+ option CONFIG_USE_FAILOVER_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=CONFIG_FAILOVER_SIZE
+ option CONFIG_XIP_ROM_SIZE=CONFIG_FAILOVER_SIZE
option COREBOOT_EXTRA_VERSION=".0-Failover"
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback" "failover"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback" "failover"
romimage "normal"
# 32K for VGA BIOS
- option ROM_SIZE = (512*1024 - 32*1024)
+ option CONFIG_ROM_SIZE = (512*1024 - 32*1024)
- option USE_FAILOVER_IMAGE=0
- option ROM_IMAGE_SIZE=0x20000
- option XIP_ROM_SIZE=0x40000
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+ option CONFIG_XIP_ROM_SIZE=0x40000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Normal"
# payload ../../../../payloads/filo_uda1.elf
payload ../payload.elf
end
romimage "fallback"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x20000
- option XIP_ROM_SIZE=0x40000
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+ option CONFIG_XIP_ROM_SIZE=0x40000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
# payload ../../../../payloads/filo_uda1.elf
payload ../payload.elf
end
romimage "failover"
- option USE_FAILOVER_IMAGE=1
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=FAILOVER_SIZE
- option XIP_ROM_SIZE=FAILOVER_SIZE
+ option CONFIG_USE_FAILOVER_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=CONFIG_FAILOVER_SIZE
+ option CONFIG_XIP_ROM_SIZE=CONFIG_FAILOVER_SIZE
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Failover"
end
-# buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
- buildrom ./coreboot.rom ROM_SIZE "normal" "fallback" "failover"
+# buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
+ buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback" "failover"
mainboard VENDOR/MAINBOARD
option CC="CROSSCC"
-option CROSS_COMPILE="CROSS_PREFIX"
-option HOSTCC="CROSS_HOSTCC"
+option CONFIG_CROSS_COMPILE="CROSS_PREFIX"
+option CONFIG_HOSTCC="CROSS_HOSTCC"
__COMPRESSION__
__LOGLEVEL__
romimage "normal"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=0x20000
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
option COREBOOT_EXTRA_VERSION=".0-normal"
payload __PAYLOAD__
end
romimage "fallback"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x20000
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
option COREBOOT_EXTRA_VERSION=".0-fallback"
payload __PAYLOAD__
end
romimage "failover"
- option USE_FAILOVER_IMAGE=1
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=FAILOVER_SIZE
- option XIP_ROM_SIZE=FAILOVER_SIZE
+ option CONFIG_USE_FAILOVER_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=CONFIG_FAILOVER_SIZE
+ option CONFIG_XIP_ROM_SIZE=CONFIG_FAILOVER_SIZE
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback" "failover"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback" "failover"
target m57sli
mainboard gigabyte/m57sli
-option ROM_SIZE=0x100000
-option FALLBACK_SIZE=(ROM_SIZE-0x1000)
+option CONFIG_ROM_SIZE=0x100000
+option CONFIG_FALLBACK_SIZE=(CONFIG_ROM_SIZE-0x1000)
romimage "fallback"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=1
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=1
option CONFIG_COMPRESSED_PAYLOAD_LZMA=1
option CONFIG_PRECOMPRESSED_PAYLOAD=1
- option ROM_IMAGE_SIZE=0x17000
- option XIP_ROM_SIZE=0x40000
+ option CONFIG_ROM_IMAGE_SIZE=0x17000
+ option CONFIG_XIP_ROM_SIZE=0x40000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
payload ../payload.elf.lzma
end
romimage "failover"
- option USE_FAILOVER_IMAGE=1
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=FAILOVER_SIZE
- option XIP_ROM_SIZE=FAILOVER_SIZE
+ option CONFIG_USE_FAILOVER_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=CONFIG_FAILOVER_SIZE
+ option CONFIG_XIP_ROM_SIZE=CONFIG_FAILOVER_SIZE
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Failover"
end
-buildrom ./coreboot.rom ROM_SIZE "fallback" "failover"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback" "failover"
# serengeti_leopard
romimage "normal"
# 48K for SCSI FW
-# option ROM_SIZE = 475136
+# option CONFIG_ROM_SIZE = 475136
# 48K for SCSI FW and 48K for ATI ROM
-# option ROM_SIZE = 425984
+# option CONFIG_ROM_SIZE = 425984
# 64K for Etherboot
-# option ROM_SIZE = 458752
+# option CONFIG_ROM_SIZE = 458752
# 44k for atixx.rom
-# option ROM_SIZE = 479232
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=0
-# option ROM_IMAGE_SIZE=0x13800
-# option ROM_IMAGE_SIZE=0x18800
- option ROM_IMAGE_SIZE=0x20000
-# option ROM_IMAGE_SIZE=0x15800
- option XIP_ROM_SIZE=0x40000
+# option CONFIG_ROM_SIZE = 479232
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=0
+# option CONFIG_ROM_IMAGE_SIZE=0x13800
+# option CONFIG_ROM_IMAGE_SIZE=0x18800
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+# option CONFIG_ROM_IMAGE_SIZE=0x15800
+ option CONFIG_XIP_ROM_SIZE=0x40000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Normal"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
end
romimage "fallback"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=1
-# option ROM_IMAGE_SIZE=0x13800
-# option ROM_IMAGE_SIZE=0x19800
- option ROM_IMAGE_SIZE=0x20000
-# option ROM_IMAGE_SIZE=0x15800
- option XIP_ROM_SIZE=0x40000
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=1
+# option CONFIG_ROM_IMAGE_SIZE=0x13800
+# option CONFIG_ROM_IMAGE_SIZE=0x19800
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+# option CONFIG_ROM_IMAGE_SIZE=0x15800
+ option CONFIG_XIP_ROM_SIZE=0x40000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
end
romimage "failover"
- option USE_FAILOVER_IMAGE=1
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=FAILOVER_SIZE
- option XIP_ROM_SIZE=FAILOVER_SIZE
+ option CONFIG_USE_FAILOVER_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=CONFIG_FAILOVER_SIZE
+ option CONFIG_XIP_ROM_SIZE=CONFIG_FAILOVER_SIZE
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Failover"
end
-#buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback" "failover"
+#buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback" "failover"
target m57sli
mainboard gigabyte/m57sli
-option ROM_SIZE=0x200000
-option FALLBACK_SIZE=(ROM_SIZE-0x1000)
+option CONFIG_ROM_SIZE=0x200000
+option CONFIG_FALLBACK_SIZE=(CONFIG_ROM_SIZE-0x1000)
romimage "fallback"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=1
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=1
option CONFIG_COMPRESSED_PAYLOAD_LZMA=1
option CONFIG_PRECOMPRESSED_PAYLOAD=1
-# option ROM_IMAGE_SIZE=0x19800
- option ROM_IMAGE_SIZE=0x17000
-# option ROM_IMAGE_SIZE=0x15800
-# option ROM_IMAGE_SIZE=0x13800
- option XIP_ROM_SIZE=0x40000
+# option CONFIG_ROM_IMAGE_SIZE=0x19800
+ option CONFIG_ROM_IMAGE_SIZE=0x17000
+# option CONFIG_ROM_IMAGE_SIZE=0x15800
+# option CONFIG_ROM_IMAGE_SIZE=0x13800
+ option CONFIG_XIP_ROM_SIZE=0x40000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
end
romimage "failover"
- option USE_FAILOVER_IMAGE=1
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=FAILOVER_SIZE
- option XIP_ROM_SIZE=FAILOVER_SIZE
+ option CONFIG_USE_FAILOVER_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=CONFIG_FAILOVER_SIZE
+ option CONFIG_XIP_ROM_SIZE=CONFIG_FAILOVER_SIZE
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Failover"
end
-buildrom ./coreboot.rom ROM_SIZE "fallback" "failover"
-#buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback" "failover"
+#buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
target dl145_g3
mainboard hp/dl145_g3
-option ROM_SIZE= 1024*1024
+option CONFIG_ROM_SIZE= 1024*1024
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
- option XIP_ROM_SIZE=0x20000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_XIP_ROM_SIZE=0x20000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
payload ./bios.bin.elf
end
-buildrom ./coreboot.rom ROM_SIZE "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback"
pci_rom ./matrox.rom vendor_id=0x102b device_id=0x0522
#
# Arima hdama
romimage "normal"
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=0x20000
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
option COREBOOT_EXTRA_VERSION=".0Normal"
# payload ../../filo.elf
payload ../../../payloads/filo.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x20000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
option COREBOOT_EXTRA_VERSION=".0Fallback"
# payload ../../filo.elf
payload ../../../payloads/filo.elf
# payload /etc/hosts
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
mainboard VENDOR/MAINBOARD
option CC="CROSSCC"
-option CROSS_COMPILE="CROSS_PREFIX"
-option HOSTCC="CROSS_HOSTCC"
+option CONFIG_CROSS_COMPILE="CROSS_PREFIX"
+option CONFIG_HOSTCC="CROSS_HOSTCC"
__COMPRESSION__
__LOGLEVEL__
-option ROM_SIZE=512*1024
+option CONFIG_ROM_SIZE=512*1024
romimage "normal"
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=0x20000
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
option COREBOOT_EXTRA_VERSION=".0-normal"
payload __PAYLOAD__
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x20000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
option COREBOOT_EXTRA_VERSION=".0-fallback"
payload __PAYLOAD__
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
###
romimage "normal"
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=0x20000
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
option COREBOOT_EXTRA_VERSION=".0Normal"
# payload ../../filo.elf
payload ../../../payloads/filo.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x20000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
option COREBOOT_EXTRA_VERSION=".0Fallback"
# payload ../../filo.elf
payload ../../../payloads/filo.elf
# payload /etc/hosts
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
mainboard VENDOR/MAINBOARD
option CC="CROSSCC"
-option CROSS_COMPILE="CROSS_PREFIX"
-option HOSTCC="CROSS_HOSTCC"
+option CONFIG_CROSS_COMPILE="CROSS_PREFIX"
+option CONFIG_HOSTCC="CROSS_HOSTCC"
__COMPRESSION__
__LOGLEVEL__
-option ROM_SIZE=256*1024
+option CONFIG_ROM_SIZE=256*1024
###
### Compute the location and size of where this firmware image
### (coreboot plus bootloader) will live in the boot rom chip.
###
-option FALLBACK_SIZE=128*1024
+option CONFIG_FALLBACK_SIZE=128*1024
romimage "normal"
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=64*1024
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=64*1024
option COREBOOT_EXTRA_VERSION=".0-Normal"
payload __PAYLOAD__
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=64*1024
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=64*1024
option COREBOOT_EXTRA_VERSION=".0-Fallback"
payload __PAYLOAD__
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
target juki-511p
mainboard iei/juki-511p
-option ROM_SIZE=256*1024
+option CONFIG_ROM_SIZE=256*1024
-option HAVE_PIRQ_TABLE=1
+option CONFIG_HAVE_PIRQ_TABLE=1
option CONFIG_COMPRESS=0
option CONFIG_PRECOMPRESSED_PAYLOAD=0
romimage "image"
- option ROM_IMAGE_SIZE=64*1024
+ option CONFIG_ROM_IMAGE_SIZE=64*1024
option COREBOOT_EXTRA_VERSION="-filo"
payload ../../filo.elf
end
-buildrom ./coreboot.rom ROM_SIZE "image"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "image"
target nova4899r
mainboard iei/nova4899r
-#option ROM_SIZE=256*1024
+#option CONFIG_ROM_SIZE=256*1024
#from OLPC definitions
option CONFIG_COMPRESSED_PAYLOAD_NRV2B=1
#option CONFIG_COMPRESSED_PAYLOAD_LZMA=1
#option CONFIG_PRECOMPRESSED_PAYLOAD=0
# leave 128k for vsa and 32k for VGA code
-option ROM_SIZE=(256*1024)-(128*1024)-(32*1024)
-option FALLBACK_SIZE=ROM_SIZE
+option CONFIG_ROM_SIZE=(256*1024)-(128*1024)-(32*1024)
+option CONFIG_FALLBACK_SIZE=CONFIG_ROM_SIZE
-option DEFAULT_CONSOLE_LOGLEVEL = 8
-option MAXIMUM_CONSOLE_LOGLEVEL = 8
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 8
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 8
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=64*1024
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=64*1024
option COREBOOT_EXTRA_VERSION=".0Fallback"
payload /opt/coreboot-SVN/filo.elf
end
-buildrom ./coreboot.rom ROM_SIZE "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback"
#"normal"
option CONFIG_COMPRESSED_PAYLOAD_LZMA = 0
# Leave 36k for VSA.
-option ROM_SIZE = (512 * 1024) - (36 * 1024)
-# option ROM_SIZE = (2048 * 1024) - (36 * 1024)
+option CONFIG_ROM_SIZE = (512 * 1024) - (36 * 1024)
+# option CONFIG_ROM_SIZE = (2048 * 1024) - (36 * 1024)
# Leave 36k for VSA, 1152k for bzImage and 750k for initrd.
-# option ROM_SIZE = (2048 * 1024) - (36 * 1024) - (1152 * 1024) - (750 * 1024)
-option FALLBACK_SIZE = ROM_SIZE
+# option CONFIG_ROM_SIZE = (2048 * 1024) - (36 * 1024) - (1152 * 1024) - (750 * 1024)
+option CONFIG_FALLBACK_SIZE = CONFIG_ROM_SIZE
-option DEFAULT_CONSOLE_LOGLEVEL = 0
-option MAXIMUM_CONSOLE_LOGLEVEL = 0
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0
romimage "fallback"
- option USE_FALLBACK_IMAGE = 1
- option ROM_IMAGE_SIZE = 80 * 1024
+ option CONFIG_USE_FALLBACK_IMAGE = 1
+ option CONFIG_ROM_IMAGE_SIZE = 80 * 1024
option COREBOOT_EXTRA_VERSION = ".0Fallback"
payload ../payload.elf
end
-buildrom ./coreboot.rom ROM_SIZE "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback"
target mtarvon
mainboard intel/mtarvon
-## ROM_SIZE is the total number of bytes allocated for coreboot use
+## CONFIG_ROM_SIZE is the total number of bytes allocated for coreboot use
## (normal AND fallback images and payloads).
-option ROM_SIZE = 2 * 1024 * 1024
+option CONFIG_ROM_SIZE = 2 * 1024 * 1024
-## ROM_IMAGE_SIZE is the maximum number of bytes allowed for a coreboot image,
+## CONFIG_ROM_IMAGE_SIZE is the maximum number of bytes allowed for a coreboot image,
## not including any payload.
-option ROM_IMAGE_SIZE = 128 * 1024
+option CONFIG_ROM_IMAGE_SIZE = 128 * 1024
-## FALLBACK_SIZE is the amount of the ROM the complete fallback image
+## CONFIG_FALLBACK_SIZE is the amount of the ROM the complete fallback image
## (including payload) will use
-option FALLBACK_SIZE = ROM_SIZE
+option CONFIG_FALLBACK_SIZE = CONFIG_ROM_SIZE
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=1
payload /tmp/filo.elf
end
-buildrom ./coreboot.rom ROM_SIZE "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback"
target truxton
mainboard intel/truxton
-## ROM_SIZE is the total number of bytes allocated for coreboot use
+## CONFIG_ROM_SIZE is the total number of bytes allocated for coreboot use
## (normal AND fallback images and payloads).
-option ROM_SIZE = 2 * 1024 * 1024
+option CONFIG_ROM_SIZE = 2 * 1024 * 1024
-## ROM_IMAGE_SIZE is the maximum number of bytes allowed for a coreboot image,
+## CONFIG_ROM_IMAGE_SIZE is the maximum number of bytes allowed for a coreboot image,
## not including any payload.
-option ROM_IMAGE_SIZE = 128 * 1024
+option CONFIG_ROM_IMAGE_SIZE = 128 * 1024
-## FALLBACK_SIZE is the amount of the ROM the complete fallback image
+## CONFIG_FALLBACK_SIZE is the amount of the ROM the complete fallback image
## (including payload) will use
-option FALLBACK_SIZE = ROM_SIZE
+option CONFIG_FALLBACK_SIZE = CONFIG_ROM_SIZE
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=1
payload /tmp/filo.elf
end
-buildrom ./coreboot.rom ROM_SIZE "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback"
target xe7501devkit
mainboard intel/xe7501devkit
-## ROM_SIZE is the total number of bytes allocated for coreboot use
+## CONFIG_ROM_SIZE is the total number of bytes allocated for coreboot use
## (normal AND fallback images and payloads).
-option ROM_SIZE = 192*1024
+option CONFIG_ROM_SIZE = 192*1024
-## ROM_IMAGE_SIZE is the maximum number of bytes allowed for a coreboot image,
+## CONFIG_ROM_IMAGE_SIZE is the maximum number of bytes allowed for a coreboot image,
## not including any payload.
-option ROM_IMAGE_SIZE = 0x1B000
+option CONFIG_ROM_IMAGE_SIZE = 0x1B000
-## FALLBACK_SIZE is the amount of the ROM the complete fallback image
+## CONFIG_FALLBACK_SIZE is the amount of the ROM the complete fallback image
## (including payload) will use
-option FALLBACK_SIZE = 0
+option CONFIG_FALLBACK_SIZE = 0
romimage "normal"
- option USE_FALLBACK_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=0
# option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Normal"
# payload ../../../../../../../memtest86/memtest
# payload ../../../../../../../etherboot/src/bin/e1000.zelf
#NOTE: CMOS currently not supported due to conflicts with factory BIOS
# Thus no support for fallback boot.
#romimage "fallback"
-# option USE_FALLBACK_IMAGE=1
+# option CONFIG_USE_FALLBACK_IMAGE=1
# option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
# payload ../../../../../../../memtest86/memtest
# payload ../../../../../../../etherboot/src/bin/e1000.zelf
# payload ../../../../../../../etherboot/src/bin/e1000--filo.zelf
#end
-buildrom ./coreboot.rom ROM_SIZE "normal"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal"
mainboard VENDOR/MAINBOARD
option CC="CROSSCC"
-option CROSS_COMPILE="CROSS_PREFIX"
-option HOSTCC="CROSS_HOSTCC"
+option CONFIG_CROSS_COMPILE="CROSS_PREFIX"
+option CONFIG_HOSTCC="CROSS_HOSTCC"
__COMPRESSION__
__LOGLEVEL__
romimage "normal"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=0x20000
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
option COREBOOT_EXTRA_VERSION=".0-normal"
payload __PAYLOAD__
end
romimage "fallback"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x20000
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
option COREBOOT_EXTRA_VERSION=".0-fallback"
payload __PAYLOAD__
end
romimage "failover"
- option USE_FAILOVER_IMAGE=1
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=FAILOVER_SIZE
- option XIP_ROM_SIZE=FAILOVER_SIZE
+ option CONFIG_USE_FAILOVER_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=CONFIG_FAILOVER_SIZE
+ option CONFIG_XIP_ROM_SIZE=CONFIG_FAILOVER_SIZE
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback" "failover"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback" "failover"
# serengeti_leopard
romimage "normal"
# 48K for SCSI FW
-# option ROM_SIZE = 475136
+# option CONFIG_ROM_SIZE = 475136
# 48K for SCSI FW and 48K for ATI ROM
-# option ROM_SIZE = 425984
+# option CONFIG_ROM_SIZE = 425984
# 64K for Etherboot
-# option ROM_SIZE = 458752
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=0
-# option ROM_IMAGE_SIZE=0x13800
-# option ROM_IMAGE_SIZE=0x17800
-# option ROM_IMAGE_SIZE=0x15800
- option ROM_IMAGE_SIZE=0x20000
- option XIP_ROM_SIZE=0x20000
+# option CONFIG_ROM_SIZE = 458752
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=0
+# option CONFIG_ROM_IMAGE_SIZE=0x13800
+# option CONFIG_ROM_IMAGE_SIZE=0x17800
+# option CONFIG_ROM_IMAGE_SIZE=0x15800
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+ option CONFIG_XIP_ROM_SIZE=0x20000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Normal"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
end
romimage "fallback"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=1
-# option ROM_IMAGE_SIZE=0x13800
-# option ROM_IMAGE_SIZE=0x17800
-# option ROM_IMAGE_SIZE=0x15800
- option ROM_IMAGE_SIZE=0x20000
- option XIP_ROM_SIZE=0x20000
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=1
+# option CONFIG_ROM_IMAGE_SIZE=0x13800
+# option CONFIG_ROM_IMAGE_SIZE=0x17800
+# option CONFIG_ROM_IMAGE_SIZE=0x15800
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+ option CONFIG_XIP_ROM_SIZE=0x20000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
end
romimage "failover"
- option USE_FAILOVER_IMAGE=1
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=FAILOVER_SIZE
- option XIP_ROM_SIZE=FAILOVER_SIZE
+ option CONFIG_USE_FAILOVER_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=CONFIG_FAILOVER_SIZE
+ option CONFIG_XIP_ROM_SIZE=CONFIG_FAILOVER_SIZE
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Failover"
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback" "failover"
-#buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback" "failover"
+#buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
mainboard iwill/dk8s2
-option HAVE_HARD_RESET=1
+option CONFIG_HAVE_HARD_RESET=1
-option HAVE_OPTION_TABLE=1
-option HAVE_MP_TABLE=1
-option ROM_SIZE=1024*1024
+option CONFIG_HAVE_OPTION_TABLE=1
+option CONFIG_HAVE_MP_TABLE=1
+option CONFIG_ROM_SIZE=1024*1024
-option HAVE_FALLBACK_BOOT=1
+option CONFIG_HAVE_FALLBACK_BOOT=1
#option CONFIG_LSI_SCSI_FW_FIXUP=1
###
### Build code to export a programmable irq routing table
###
-option HAVE_PIRQ_TABLE=1
-option IRQ_SLOT_COUNT=12
+option CONFIG_HAVE_PIRQ_TABLE=1
+option CONFIG_IRQ_SLOT_COUNT=12
#
###
### Build code for SMP support
option CONFIG_IOAPIC=1
#
###
-### MEMORY_HOLE instructs earlymtrr.inc to
+### CONFIG_MEMORY_HOLE instructs earlymtrr.inc to
### enable caching from 0-640KB and to disable
### caching from 640KB-1MB using fixed MTRRs
###
### CPU identification depends on only variable MTRRs
### being enabled.
###
-#option MEMORY_HOLE=0
+#option CONFIG_MEMORY_HOLE=0
#
###
### Clean up the motherboard id strings
###
-option MAINBOARD_PART_NUMBER="DK8S2"
-option MAINBOARD_VENDOR="IWILL"
+option CONFIG_MAINBOARD_PART_NUMBER="DK8S2"
+option CONFIG_MAINBOARD_VENDOR="IWILL"
#
###
### Compute the location and size of where this firmware image
### (coreboot plus bootloader) will live in the boot rom chip.
###
-#option FALLBACK_SIZE=524288
-#option FALLBACK_SIZE=98304
-option FALLBACK_SIZE=131072
+#option CONFIG_FALLBACK_SIZE=524288
+#option CONFIG_FALLBACK_SIZE=98304
+option CONFIG_FALLBACK_SIZE=131072
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-option ROM_IMAGE_SIZE=65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+option CONFIG_ROM_IMAGE_SIZE=65536
###
#option CONFIG_COMPRESS=1
option CONFIG_CONSOLE_SERIAL8250=1
-option TTYS0_BAUD=115200
+option CONFIG_TTYS0_BAUD=115200
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-option DEFAULT_CONSOLE_LOGLEVEL=7
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL=7
## At a maximum only compile in this level of debugging
-option MAXIMUM_CONSOLE_LOGLEVEL=7
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=7
-#option DEBUG=1
+#option CONFIG_DEBUG=1
#
## Coreboot C code runs at this location in RAM
-option _RAMBASE=0x004000
+option CONFIG_RAMBASE=0x004000
##
## Use a 32K stack
##
-option STACK_SIZE=0x8000
+option CONFIG_STACK_SIZE=0x8000
##
## Use a 56K heap
##
-option HEAP_SIZE=0xe000
+option CONFIG_HEAP_SIZE=0xe000
#
###
#
romimage "normal"
# 48K for SCSI FW
-# option ROM_SIZE = 512*1024-48*1024
+# option CONFIG_ROM_SIZE = 512*1024-48*1024
# 48K for SCSI FW and 48K for ATI ROM
-# option ROM_SIZE = 512*1024-48*1024-48*1024
+# option CONFIG_ROM_SIZE = 512*1024-48*1024-48*1024
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Normal"
- option USE_FALLBACK_IMAGE=0
- option ROM_SECTION_SIZE = (ROM_SIZE - FALLBACK_SIZE)
- option ROM_SECTION_OFFSET= 0
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_SECTION_SIZE = (CONFIG_ROM_SIZE - CONFIG_FALLBACK_SIZE)
+ option CONFIG_ROM_SECTION_OFFSET= 0
- option PAYLOAD_SIZE = (ROM_SECTION_SIZE - ROM_IMAGE_SIZE)
- option CONFIG_ROM_PAYLOAD_START = (0xffffffff - ROM_SIZE + ROM_SECTION_OFFSET + 1)
- option _ROMBASE = (CONFIG_ROM_PAYLOAD_START + PAYLOAD_SIZE)
+ option CONFIG_PAYLOAD_SIZE = (CONFIG_ROM_SECTION_SIZE - CONFIG_ROM_IMAGE_SIZE)
+ option CONFIG_ROM_PAYLOAD_START = (0xffffffff - CONFIG_ROM_SIZE + CONFIG_ROM_SECTION_OFFSET + 1)
+ option CONFIG_ROMBASE = (CONFIG_ROM_PAYLOAD_START + CONFIG_PAYLOAD_SIZE)
-# option XIP_ROM_SIZE = FALLBACK_SIZE
- option XIP_ROM_SIZE = 65536
+# option CONFIG_XIP_ROM_SIZE = CONFIG_FALLBACK_SIZE
+ option CONFIG_XIP_ROM_SIZE = 65536
- option XIP_ROM_BASE = (_ROMBASE + ROM_IMAGE_SIZE - XIP_ROM_SIZE)
+ option CONFIG_XIP_ROM_BASE = (CONFIG_ROMBASE + CONFIG_ROM_IMAGE_SIZE - CONFIG_XIP_ROM_SIZE)
payload /usr/src/filo-0.4.1_btext/filo.elf
# payload /usr/src/filo-0.4.2/filo.elf
romimage "fallback"
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
- option USE_FALLBACK_IMAGE=1
- option ROM_SECTION_SIZE = FALLBACK_SIZE
- option ROM_SECTION_OFFSET= (ROM_SIZE - FALLBACK_SIZE)
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_SECTION_SIZE = CONFIG_FALLBACK_SIZE
+ option CONFIG_ROM_SECTION_OFFSET= (CONFIG_ROM_SIZE - CONFIG_FALLBACK_SIZE)
- option PAYLOAD_SIZE = (ROM_SECTION_SIZE - ROM_IMAGE_SIZE)
- option CONFIG_ROM_PAYLOAD_START = (0xffffffff - ROM_SIZE + ROM_SECTION_OFFSET + 1)
- option _ROMBASE = (CONFIG_ROM_PAYLOAD_START + PAYLOAD_SIZE)
+ option CONFIG_PAYLOAD_SIZE = (CONFIG_ROM_SECTION_SIZE - CONFIG_ROM_IMAGE_SIZE)
+ option CONFIG_ROM_PAYLOAD_START = (0xffffffff - CONFIG_ROM_SIZE + CONFIG_ROM_SECTION_OFFSET + 1)
+ option CONFIG_ROMBASE = (CONFIG_ROM_PAYLOAD_START + CONFIG_PAYLOAD_SIZE)
-# option XIP_ROM_SIZE = FALLBACK_SIZE
- option XIP_ROM_SIZE = 65536
- option XIP_ROM_BASE = (_ROMBASE + ROM_IMAGE_SIZE - XIP_ROM_SIZE)
+# option CONFIG_XIP_ROM_SIZE = CONFIG_FALLBACK_SIZE
+ option CONFIG_XIP_ROM_SIZE = 65536
+ option CONFIG_XIP_ROM_BASE = (CONFIG_ROMBASE + CONFIG_ROM_IMAGE_SIZE - CONFIG_XIP_ROM_SIZE)
payload ../../../payloads/filo.elf
# payload /usr/src/filo-0.4.2/filo.elf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
mainboard iwill/dk8x
-option HAVE_HARD_RESET=1
+option CONFIG_HAVE_HARD_RESET=1
-option HAVE_OPTION_TABLE=1
-option HAVE_MP_TABLE=1
-option ROM_SIZE=1024*1024
+option CONFIG_HAVE_OPTION_TABLE=1
+option CONFIG_HAVE_MP_TABLE=1
+option CONFIG_ROM_SIZE=1024*1024
-option HAVE_FALLBACK_BOOT=1
+option CONFIG_HAVE_FALLBACK_BOOT=1
#option CONFIG_LSI_SCSI_FW_FIXUP=1
###
### Build code to export a programmable irq routing table
###
-option HAVE_PIRQ_TABLE=1
-option IRQ_SLOT_COUNT=12
+option CONFIG_HAVE_PIRQ_TABLE=1
+option CONFIG_IRQ_SLOT_COUNT=12
#
###
### Build code for SMP support
option CONFIG_IOAPIC=1
#
###
-### MEMORY_HOLE instructs earlymtrr.inc to
+### CONFIG_MEMORY_HOLE instructs earlymtrr.inc to
### enable caching from 0-640KB and to disable
### caching from 640KB-1MB using fixed MTRRs
###
### CPU identification depends on only variable MTRRs
### being enabled.
###
-#option MEMORY_HOLE=0
+#option CONFIG_MEMORY_HOLE=0
#
###
### Clean up the motherboard id strings
###
-option MAINBOARD_PART_NUMBER="DK8X"
-option MAINBOARD_VENDOR="IWILL"
+option CONFIG_MAINBOARD_PART_NUMBER="DK8X"
+option CONFIG_MAINBOARD_VENDOR="IWILL"
#
###
### Compute the location and size of where this firmware image
### (coreboot plus bootloader) will live in the boot rom chip.
###
-#option FALLBACK_SIZE=524288
-#option FALLBACK_SIZE=98304
-option FALLBACK_SIZE=131072
+#option CONFIG_FALLBACK_SIZE=524288
+#option CONFIG_FALLBACK_SIZE=98304
+option CONFIG_FALLBACK_SIZE=131072
-## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-option ROM_IMAGE_SIZE=65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+option CONFIG_ROM_IMAGE_SIZE=65536
###
#option CONFIG_COMPRESS=1
option CONFIG_CONSOLE_SERIAL8250=1
-option TTYS0_BAUD=115200
+option CONFIG_TTYS0_BAUD=115200
##
### Select the coreboot loglevel
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-option DEFAULT_CONSOLE_LOGLEVEL=7
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL=7
## At a maximum only compile in this level of debugging
-option MAXIMUM_CONSOLE_LOGLEVEL=7
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=7
-#option DEBUG=1
+#option CONFIG_DEBUG=1
#
## Coreboot C code runs at this location in RAM
-option _RAMBASE=0x004000
+option CONFIG_RAMBASE=0x004000
##
## Use a 32K stack
##
-option STACK_SIZE=0x8000
+option CONFIG_STACK_SIZE=0x8000
##
## Use a 56K heap
##
-option HEAP_SIZE=0xe000
+option CONFIG_HEAP_SIZE=0xe000
#
###
#
romimage "normal"
# 48K for SCSI FW
-# option ROM_SIZE = 512*1024-48*1024
+# option CONFIG_ROM_SIZE = 512*1024-48*1024
# 48K for SCSI FW and 48K for ATI ROM
-# option ROM_SIZE = 512*1024-48*1024-48*1024
+# option CONFIG_ROM_SIZE = 512*1024-48*1024-48*1024
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Normal"
- option USE_FALLBACK_IMAGE=0
- option ROM_SECTION_SIZE = (ROM_SIZE - FALLBACK_SIZE)
- option ROM_SECTION_OFFSET= 0
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_SECTION_SIZE = (CONFIG_ROM_SIZE - CONFIG_FALLBACK_SIZE)
+ option CONFIG_ROM_SECTION_OFFSET= 0
- option PAYLOAD_SIZE = (ROM_SECTION_SIZE - ROM_IMAGE_SIZE)
- option CONFIG_ROM_PAYLOAD_START = (0xffffffff - ROM_SIZE + ROM_SECTION_OFFSET + 1)
- option _ROMBASE = (CONFIG_ROM_PAYLOAD_START + PAYLOAD_SIZE)
+ option CONFIG_PAYLOAD_SIZE = (CONFIG_ROM_SECTION_SIZE - CONFIG_ROM_IMAGE_SIZE)
+ option CONFIG_ROM_PAYLOAD_START = (0xffffffff - CONFIG_ROM_SIZE + CONFIG_ROM_SECTION_OFFSET + 1)
+ option CONFIG_ROMBASE = (CONFIG_ROM_PAYLOAD_START + CONFIG_PAYLOAD_SIZE)
-# option XIP_ROM_SIZE = FALLBACK_SIZE
- option XIP_ROM_SIZE = 65536
+# option CONFIG_XIP_ROM_SIZE = CONFIG_FALLBACK_SIZE
+ option CONFIG_XIP_ROM_SIZE = 65536
- option XIP_ROM_BASE = (_ROMBASE + ROM_IMAGE_SIZE - XIP_ROM_SIZE)
+ option CONFIG_XIP_ROM_BASE = (CONFIG_ROMBASE + CONFIG_ROM_IMAGE_SIZE - CONFIG_XIP_ROM_SIZE)
payload /usr/src/filo-0.4.1_btext/filo.elf
# payload /usr/src/filo-0.4.2/filo.elf
romimage "fallback"
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
- option USE_FALLBACK_IMAGE=1
- option ROM_SECTION_SIZE = FALLBACK_SIZE
- option ROM_SECTION_OFFSET= (ROM_SIZE - FALLBACK_SIZE)
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_SECTION_SIZE = CONFIG_FALLBACK_SIZE
+ option CONFIG_ROM_SECTION_OFFSET= (CONFIG_ROM_SIZE - CONFIG_FALLBACK_SIZE)
- option PAYLOAD_SIZE = (ROM_SECTION_SIZE - ROM_IMAGE_SIZE)
- option CONFIG_ROM_PAYLOAD_START = (0xffffffff - ROM_SIZE + ROM_SECTION_OFFSET + 1)
- option _ROMBASE = (CONFIG_ROM_PAYLOAD_START + PAYLOAD_SIZE)
+ option CONFIG_PAYLOAD_SIZE = (CONFIG_ROM_SECTION_SIZE - CONFIG_ROM_IMAGE_SIZE)
+ option CONFIG_ROM_PAYLOAD_START = (0xffffffff - CONFIG_ROM_SIZE + CONFIG_ROM_SECTION_OFFSET + 1)
+ option CONFIG_ROMBASE = (CONFIG_ROM_PAYLOAD_START + CONFIG_PAYLOAD_SIZE)
-# option XIP_ROM_SIZE = FALLBACK_SIZE
- option XIP_ROM_SIZE = 65536
- option XIP_ROM_BASE = (_ROMBASE + ROM_IMAGE_SIZE - XIP_ROM_SIZE)
+# option CONFIG_XIP_ROM_SIZE = CONFIG_FALLBACK_SIZE
+ option CONFIG_XIP_ROM_SIZE = 65536
+ option CONFIG_XIP_ROM_BASE = (CONFIG_ROMBASE + CONFIG_ROM_IMAGE_SIZE - CONFIG_XIP_ROM_SIZE)
payload ../../../payloads/filo.elf
# payload /usr/src/filo-0.4.2/filo.elf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
mainboard VENDOR/MAINBOARD
option CC="CROSSCC"
-option CROSS_COMPILE="CROSS_PREFIX"
-option HOSTCC="CROSS_HOSTCC"
+option CONFIG_CROSS_COMPILE="CROSS_PREFIX"
+option CONFIG_HOSTCC="CROSS_HOSTCC"
__COMPRESSION__
__LOGLEVEL__
-option ROM_SIZE=512*1024
+option CONFIG_ROM_SIZE=512*1024
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x20000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
option COREBOOT_EXTRA_VERSION=".0-fallback"
payload __PAYLOAD__
end
-buildrom ./coreboot.rom ROM_SIZE "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback"
target jetway-j7f24
mainboard jetway/j7f24
-option MAXIMUM_CONSOLE_LOGLEVEL=8
-option DEFAULT_CONSOLE_LOGLEVEL=8
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
option CONFIG_CONSOLE_SERIAL8250=1
# coreboot C code runs at this location in RAM
-option _RAMBASE=0x00004000
+option CONFIG_RAMBASE=0x00004000
#
# If space is allotted for a VGA BIOS,
# generate the final ROM like this:
# cat vgabios bochsbios coreboot.rom > coreboot.rom.final
#
-#option ROM_SIZE = (512 * 1024) - (63 * 1024) - (64 * 1024)
-option ROM_SIZE = (512 * 1024)
+#option CONFIG_ROM_SIZE = (512 * 1024) - (63 * 1024) - (64 * 1024)
+option CONFIG_ROM_SIZE = (512 * 1024)
romimage "image"
option COREBOOT_EXTRA_VERSION = "-j7f24"
payload ../payload.elf
end
-buildrom ./coreboot.rom ROM_SIZE "image"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "image"
mainboard VENDOR/MAINBOARD
option CC="CROSSCC"
-option CROSS_COMPILE="CROSS_PREFIX"
-option HOSTCC="CROSS_HOSTCC"
+option CONFIG_CROSS_COMPILE="CROSS_PREFIX"
+option CONFIG_HOSTCC="CROSS_HOSTCC"
__COMPRESSION__
__LOGLEVEL__
-option ROM_SIZE=1024*1024
+option CONFIG_ROM_SIZE=1024*1024
romimage "normal"
- option USE_FALLBACK_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=0
option COREBOOT_EXTRA_VERSION=".0-normal"
payload __PAYLOAD__
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=1
option COREBOOT_EXTRA_VERSION=".0-fallback"
payload __PAYLOAD__
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
#pci_rom ../../../misc/kontron-pci8086,27a2.rom vendor_id=0x8086 device_id=0x27a2
target kontron_986lcd_m
mainboard kontron/986lcd-m
-## ROM_SIZE is the total number of bytes allocated for coreboot use
+## CONFIG_ROM_SIZE is the total number of bytes allocated for coreboot use
## (normal AND fallback images and payloads).
-option ROM_SIZE = 1024 * 1024
+option CONFIG_ROM_SIZE = 1024 * 1024
romimage "fallback"
- option USE_FALLBACK_IMAGE = 1
+ option CONFIG_USE_FALLBACK_IMAGE = 1
payload ../payload.elf
end
-buildrom ./coreboot.rom ROM_SIZE "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback"
# Uncomment this and fix the path to your VGA BIOS blob (~/amipci_01.20 here) for on-board VGA support.
# See http://www.coreboot.org/Kontron_986LCD-M_mITX for details.
target frontrunner
mainboard lippert/frontrunner
-option ROM_SIZE=256*1024
+option CONFIG_ROM_SIZE=256*1024
romimage "normal"
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=0x16000
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=0x16000
option COREBOOT_EXTRA_VERSION=".0Normal"
# payload /usr/share/etherboot/5.1.9pre2-lnxi-lb/tg3--ide_disk.zelf
# payload ../../../../tg3--ide_disk.zelf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x16000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x16000
option COREBOOT_EXTRA_VERSION=".0Fallback"
# payload /usr/share/etherboot/5.1.9pre2-lnxi-lb/tg3--ide_disk.zelf
# payload ../../../../tg3--ide_disk.zelf
payload /tmp/filo.elf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
#option CONFIG_IDE = 1
#option CONFIG_FS_PAYLOAD = 1
#option CONFIG_FS_EXT2 = 1
-#option AUTOBOOT_DELAY = 0
-#option AUTOBOOT_CMDLINE = "hda1:/payload.elf"
+#option CONFIG_AUTOBOOT_DELAY = 0
+#option CONFIG_AUTOBOOT_CMDLINE = "hda1:/payload.elf"
# Leave 36k for VSA. Usually board is equipped with a 512 KB FWH (LPC) flash,
# however it can be replaced with a 1 MB chip.
-option ROM_SIZE = (512 * 1024) - (36 * 1024)
-#option ROM_SIZE = (1024 * 1024) - (36 * 1024)
-option FALLBACK_SIZE = ROM_SIZE
+option CONFIG_ROM_SIZE = (512 * 1024) - (36 * 1024)
+#option CONFIG_ROM_SIZE = (1024 * 1024) - (36 * 1024)
+option CONFIG_FALLBACK_SIZE = CONFIG_ROM_SIZE
-#option DEFAULT_CONSOLE_LOGLEVEL = 4
-#option MAXIMUM_CONSOLE_LOGLEVEL = 4
+#option CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 4
+#option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 4
-# Saves space on ROM_IMAGE_SIZE, but decompression costs a second on boot.
+# Saves space on CONFIG_ROM_IMAGE_SIZE, but decompression costs a second on boot.
option CONFIG_COMPRESS = 1
romimage "image"
- option USE_FALLBACK_IMAGE = 1
- option ROM_IMAGE_SIZE = 64 * 1024
+ option CONFIG_USE_FALLBACK_IMAGE = 1
+ option CONFIG_ROM_IMAGE_SIZE = 64 * 1024
option COREBOOT_EXTRA_VERSION = ".0"
payload ../payload.elf
# If getting payload from IDE
# payload /dev/null
end
-buildrom ./coreboot.rom ROM_SIZE "image"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "image"
#option CONFIG_IDE = 1
#option CONFIG_FS_PAYLOAD = 1
#option CONFIG_FS_EXT2 = 1
-#option AUTOBOOT_DELAY = 0
-#option AUTOBOOT_CMDLINE = "hda1:/payload.elf"
+#option CONFIG_AUTOBOOT_DELAY = 0
+#option CONFIG_AUTOBOOT_CMDLINE = "hda1:/payload.elf"
# Leave 36k for VSA. Board is equipped with a 1 MB SPI flash, however, due to
# limitations of the IT8712F Super I/O, only the top 512 KB are directly mapped.
-option ROM_SIZE = (512 * 1024) - (36 * 1024)
-option FALLBACK_SIZE = ROM_SIZE
+option CONFIG_ROM_SIZE = (512 * 1024) - (36 * 1024)
+option CONFIG_FALLBACK_SIZE = CONFIG_ROM_SIZE
-#option DEFAULT_CONSOLE_LOGLEVEL = 4
-#option MAXIMUM_CONSOLE_LOGLEVEL = 4
+#option CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 4
+#option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 4
-# Saves space on ROM_IMAGE_SIZE, but decompression costs a second on boot.
+# Saves space on CONFIG_ROM_IMAGE_SIZE, but decompression costs a second on boot.
option CONFIG_COMPRESS = 1
romimage "image"
- option USE_FALLBACK_IMAGE = 1
- option ROM_IMAGE_SIZE = 64 * 1024
+ option CONFIG_USE_FALLBACK_IMAGE = 1
+ option CONFIG_ROM_IMAGE_SIZE = 64 * 1024
option COREBOOT_EXTRA_VERSION = ".0"
payload ../payload.elf
# If getting payload from IDE
# payload /dev/null
end
-buildrom ./coreboot.rom ROM_SIZE "image"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "image"
# Apache Demo Board
romimage "normal"
## Base of ROM
- option _ROMBASE=0xfff00000
+ option CONFIG_ROMBASE=0xfff00000
## Apache reset vector
- option _RESET=_ROMBASE+0x100
+ option CONFIG_RESET=CONFIG_ROMBASE+0x100
## Exception vectors (other than reset vector)
- option _EXCEPTION_VECTORS=_RESET+0x100
+ option CONFIG_EXCEPTION_VECTORS=CONFIG_RESET+0x100
## Start of coreboot in the boot rom
- ## = _RESET + exeception vector table size
- option _ROMSTART=_RESET+0x3100
+ ## = CONFIG_RESET + exeception vector table size
+ option CONFIG_ROMSTART=CONFIG_RESET+0x3100
## Coreboot C code runs at this location in RAM
- option _RAMBASE=0x00100000
- option _RAMSTART=0x00100000
+ option CONFIG_RAMBASE=0x00100000
+ option CONFIG_RAMSTART=0x00100000
end
-buildrom ./coreboot.rom ROM_SIZE "normal"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal"
# Sandpoint Demo Board
romimage "normal"
## Base of ROM
- option _ROMBASE=0xfff00000
+ option CONFIG_ROMBASE=0xfff00000
## Sandpoint reset vector
- option _RESET=_ROMBASE+0x100
+ option CONFIG_RESET=CONFIG_ROMBASE+0x100
## Exception vectors (other than reset vector)
- option _EXCEPTION_VECTORS=_RESET+0x100
+ option CONFIG_EXCEPTION_VECTORS=CONFIG_RESET+0x100
## Start of coreboot in the boot rom
- ## = _RESET + exeception vector table size
- option _ROMSTART=_RESET+0x3100
+ ## = CONFIG_RESET + exeception vector table size
+ option CONFIG_ROMSTART=CONFIG_RESET+0x3100
## Coreboot C code runs at this location in RAM
- option _RAMBASE=0x00100000
- option _RAMSTART=0x00100000
+ option CONFIG_RAMBASE=0x00100000
+ option CONFIG_RAMSTART=0x00100000
option CONFIG_SANDPOINT_ALTIMUS=1
end
-buildrom ./coreboot.rom ROM_SIZE "normal"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal"
target sandpoint
-uses CROSS_COMPILE
-uses HAVE_OPTION_TABLE
+uses CONFIG_CROSS_COMPILE
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_SANDPOINT_ALTIMUS
uses CONFIG_COMPRESS
-uses DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
uses CONFIG_USE_INIT
uses CONFIG_CHIP_CONFIGURE
-uses NO_POST
+uses CONFIG_NO_POST
uses CONFIG_CONSOLE_SERIAL8250
-uses TTYS0_BASE
+uses CONFIG_TTYS0_BASE
uses CONFIG_IDE_PAYLOAD
-uses IDE_BOOT_DRIVE
-uses IDE_SWAB IDE_OFFSET
-uses ROM_SIZE
-uses _RESET
-uses _EXCEPTION_VECTORS
-uses _ROMBASE
-uses _ROMSTART
-uses _RAMBASE
-uses _RAMSTART
-uses STACK_SIZE
-uses HEAP_SIZE
+uses CONFIG_IDE_BOOT_DRIVE
+uses CONFIG_IDE_SWAB CONFIG_IDE_OFFSET
+uses CONFIG_ROM_SIZE
+uses CONFIG_RESET
+uses CONFIG_EXCEPTION_VECTORS
+uses CONFIG_ROMBASE
+uses CONFIG_ROMSTART
+uses CONFIG_RAMBASE
+uses CONFIG_RAMSTART
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
## use a cross compiler
-#option CROSS_COMPILE="powerpc-eabi-"
-#option CROSS_COMPILE="ppc_74xx-"
+#option CONFIG_CROSS_COMPILE="powerpc-eabi-"
+#option CONFIG_CROSS_COMPILE="ppc_74xx-"
## Use stage 1 initialization code
option CONFIG_USE_INIT=1
option CONFIG_COMPRESS=0
## Turn off POST codes
-option NO_POST=1
+option CONFIG_NO_POST=1
## Enable serial console
-option DEFAULT_CONSOLE_LOGLEVEL=8
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
option CONFIG_CONSOLE_SERIAL8250=1
-option TTYS0_BASE=0x3f8
+option CONFIG_TTYS0_BASE=0x3f8
## Boot linux from IDE
option CONFIG_IDE_PAYLOAD=1
-option IDE_BOOT_DRIVE=0
-option IDE_SWAB=1
-option IDE_OFFSET=0
+option CONFIG_IDE_BOOT_DRIVE=0
+option CONFIG_IDE_SWAB=1
+option CONFIG_IDE_OFFSET=0
# ROM is 1Mb
-option ROM_SIZE=1024*1024
+option CONFIG_ROM_SIZE=1024*1024
# Set stack and heap sizes (stage 2)
-option STACK_SIZE=0x10000
-option HEAP_SIZE=0x10000
+option CONFIG_STACK_SIZE=0x10000
+option CONFIG_HEAP_SIZE=0x10000
# Sandpoint Demo Board
romimage "normal"
## Base of ROM
- option _ROMBASE=0xfff00000
+ option CONFIG_ROMBASE=0xfff00000
## Sandpoint reset vector
- option _RESET=_ROMBASE+0x100
+ option CONFIG_RESET=CONFIG_ROMBASE+0x100
## Exception vectors (other than reset vector)
- option _EXCEPTION_VECTORS=_RESET+0x100
+ option CONFIG_EXCEPTION_VECTORS=CONFIG_RESET+0x100
## Start of coreboot in the boot rom
- ## = _RESET + exeception vector table size
- option _ROMSTART=_RESET+0x3100
+ ## = CONFIG_RESET + exeception vector table size
+ option CONFIG_ROMSTART=CONFIG_RESET+0x3100
## Coreboot C code runs at this location in RAM
- option _RAMBASE=0x00100000
- option _RAMSTART=0x00100000
+ option CONFIG_RAMBASE=0x00100000
+ option CONFIG_RAMSTART=0x00100000
option CONFIG_SANDPOINT_ALTIMUS=1
mainboard motorola/sandpoint
end
-buildrom ./coreboot.rom ROM_SIZE "normal"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal"
target ms6119
mainboard msi/ms6119
-option ROM_SIZE = 256 * 1024
+option CONFIG_ROM_SIZE = 256 * 1024
-option MAINBOARD_VENDOR = "MSI"
-option MAINBOARD_PART_NUMBER = "MS-6119"
+option CONFIG_MAINBOARD_VENDOR = "MSI"
+option CONFIG_MAINBOARD_PART_NUMBER = "MS-6119"
-option IRQ_SLOT_COUNT = 7
+option CONFIG_IRQ_SLOT_COUNT = 7
-option DEFAULT_CONSOLE_LOGLEVEL = 9
-option MAXIMUM_CONSOLE_LOGLEVEL = 9
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
option CONFIG_CONSOLE_VGA = 1
option CONFIG_PCI_ROM_RUN = 1
romimage "normal"
- option USE_FALLBACK_IMAGE = 0
+ option CONFIG_USE_FALLBACK_IMAGE = 0
option COREBOOT_EXTRA_VERSION = ".0Normal"
payload /tmp/filo.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE = 1
+ option CONFIG_USE_FALLBACK_IMAGE = 1
option COREBOOT_EXTRA_VERSION = ".0Fallback"
payload /tmp/filo.elf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
target ms6147
mainboard msi/ms6147
-option ROM_SIZE = 256 * 1024
+option CONFIG_ROM_SIZE = 256 * 1024
-option MAINBOARD_VENDOR = "MSI"
-option MAINBOARD_PART_NUMBER = "MS-6147"
+option CONFIG_MAINBOARD_VENDOR = "MSI"
+option CONFIG_MAINBOARD_PART_NUMBER = "MS-6147"
-option IRQ_SLOT_COUNT = 8
+option CONFIG_IRQ_SLOT_COUNT = 8
-option DEFAULT_CONSOLE_LOGLEVEL = 9
-option MAXIMUM_CONSOLE_LOGLEVEL = 9
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
option CONFIG_CONSOLE_VGA = 1
option CONFIG_PCI_ROM_RUN = 1
romimage "normal"
- option USE_FALLBACK_IMAGE = 0
+ option CONFIG_USE_FALLBACK_IMAGE = 0
option COREBOOT_EXTRA_VERSION = ".Normal"
payload ../payload.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE = 1
+ option CONFIG_USE_FALLBACK_IMAGE = 1
option COREBOOT_EXTRA_VERSION = ".Fallback"
payload ../payload.elf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
target ms6178
mainboard msi/ms6178
-option ROM_SIZE = 512 * 1024
+option CONFIG_ROM_SIZE = 512 * 1024
-option MAINBOARD_VENDOR = "MSI"
-option MAINBOARD_PART_NUMBER = "MS-6178"
+option CONFIG_MAINBOARD_VENDOR = "MSI"
+option CONFIG_MAINBOARD_PART_NUMBER = "MS-6178"
-option IRQ_SLOT_COUNT = 4
+option CONFIG_IRQ_SLOT_COUNT = 4
-option DEFAULT_CONSOLE_LOGLEVEL = 9
-option MAXIMUM_CONSOLE_LOGLEVEL = 9
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
option CONFIG_CONSOLE_VGA = 1
option CONFIG_PCI_ROM_RUN = 1
romimage "normal"
- option USE_FALLBACK_IMAGE = 0
+ option CONFIG_USE_FALLBACK_IMAGE = 0
option COREBOOT_EXTRA_VERSION = ".0Normal"
payload /tmp/filo.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE = 1
+ option CONFIG_USE_FALLBACK_IMAGE = 1
option COREBOOT_EXTRA_VERSION = ".0Fallback"
payload /tmp/filo.elf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
# pci_rom i810.vga vendor_id=0x8086 device_id=0x7120
mainboard VENDOR/MAINBOARD
option CC="CROSSCC"
-option CROSS_COMPILE="CROSS_PREFIX"
-option HOSTCC="CROSS_HOSTCC"
+option CONFIG_CROSS_COMPILE="CROSS_PREFIX"
+option CONFIG_HOSTCC="CROSS_HOSTCC"
__COMPRESSION__
__LOGLEVEL__
romimage "normal"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=0x20000
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
option COREBOOT_EXTRA_VERSION=".0-normal"
payload __PAYLOAD__
end
romimage "fallback"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x20000
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
option COREBOOT_EXTRA_VERSION=".0-fallback"
payload __PAYLOAD__
end
romimage "failover"
- option USE_FAILOVER_IMAGE=1
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=FAILOVER_SIZE
- option XIP_ROM_SIZE=FAILOVER_SIZE
+ option CONFIG_USE_FAILOVER_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=CONFIG_FAILOVER_SIZE
+ option CONFIG_XIP_ROM_SIZE=CONFIG_FAILOVER_SIZE
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback" "failover"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback" "failover"
target ms7135
mainboard msi/ms7135
-option DEFAULT_CONSOLE_LOGLEVEL=8
-option MAXIMUM_CONSOLE_LOGLEVEL=8
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
-option HAVE_PIRQ_TABLE=1
+option CONFIG_HAVE_PIRQ_TABLE=1
option CONFIG_CONSOLE_VGA=1
option CONFIG_PCI_ROM_RUN=1
romimage "normal"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=0x20000
- option XIP_ROM_SIZE=0x20000
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+ option CONFIG_XIP_ROM_SIZE=0x20000
option COREBOOT_EXTRA_VERSION="_Normal"
payload /tmp/payload.elf
end
romimage "fallback"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x20000
- option XIP_ROM_SIZE=0x20000
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+ option CONFIG_XIP_ROM_SIZE=0x20000
option COREBOOT_EXTRA_VERSION="_Fallback"
payload /tmp/payload.elf
end
romimage "failover"
- option USE_FAILOVER_IMAGE=1
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=FAILOVER_SIZE
- option XIP_ROM_SIZE=FAILOVER_SIZE
+ option CONFIG_USE_FAILOVER_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=CONFIG_FAILOVER_SIZE
+ option CONFIG_XIP_ROM_SIZE=CONFIG_FAILOVER_SIZE
option COREBOOT_EXTRA_VERSION="_Failover"
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback" "failover"
-#buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback" "failover"
+#buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
mainboard VENDOR/MAINBOARD
option CC="CROSSCC"
-option CROSS_COMPILE="CROSS_PREFIX"
-option HOSTCC="CROSS_HOSTCC"
+option CONFIG_CROSS_COMPILE="CROSS_PREFIX"
+option CONFIG_HOSTCC="CROSS_HOSTCC"
__COMPRESSION__
__LOGLEVEL__
romimage "normal"
- option USE_FAILOVER_IMAGE = 0
- option USE_FALLBACK_IMAGE = 0
- option ROM_IMAGE_SIZE = 128 * 1024
- option XIP_ROM_SIZE = 256 * 1024
+ option CONFIG_USE_FAILOVER_IMAGE = 0
+ option CONFIG_USE_FALLBACK_IMAGE = 0
+ option CONFIG_ROM_IMAGE_SIZE = 128 * 1024
+ option CONFIG_XIP_ROM_SIZE = 256 * 1024
option COREBOOT_EXTRA_VERSION = ".0Normal"
payload __PAYLOAD__
end
romimage "fallback"
- option USE_FAILOVER_IMAGE = 0
- option USE_FALLBACK_IMAGE = 1
- option ROM_IMAGE_SIZE = 128 * 1024
- option XIP_ROM_SIZE = 256 * 1024
+ option CONFIG_USE_FAILOVER_IMAGE = 0
+ option CONFIG_USE_FALLBACK_IMAGE = 1
+ option CONFIG_ROM_IMAGE_SIZE = 128 * 1024
+ option CONFIG_XIP_ROM_SIZE = 256 * 1024
option COREBOOT_EXTRA_VERSION = ".0Fallback"
payload __PAYLOAD__
end
romimage "failover"
- option USE_FAILOVER_IMAGE = 1
- option USE_FALLBACK_IMAGE = 0
- option ROM_IMAGE_SIZE = FAILOVER_SIZE
- option XIP_ROM_SIZE = FAILOVER_SIZE
+ option CONFIG_USE_FAILOVER_IMAGE = 1
+ option CONFIG_USE_FALLBACK_IMAGE = 0
+ option CONFIG_ROM_IMAGE_SIZE = CONFIG_FAILOVER_SIZE
+ option CONFIG_XIP_ROM_SIZE = CONFIG_FAILOVER_SIZE
option COREBOOT_EXTRA_VERSION = ".0Failover"
end
-# buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback" "failover"
+# buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback" "failover"
target ms7260
mainboard msi/ms7260
-option ROM_SIZE = 512 * 1024
+option CONFIG_ROM_SIZE = 512 * 1024
option CONFIG_COMPRESSED_PAYLOAD_NRV2B = 1 # NRV2B compression
# option CONFIG_COMPRESSED_PAYLOAD_LZMA = 1 # LZMA compression
romimage "normal"
- option USE_FAILOVER_IMAGE = 0
- option USE_FALLBACK_IMAGE = 0
- option ROM_IMAGE_SIZE = 128 * 1024
- option XIP_ROM_SIZE = 256 * 1024
+ option CONFIG_USE_FAILOVER_IMAGE = 0
+ option CONFIG_USE_FALLBACK_IMAGE = 0
+ option CONFIG_ROM_IMAGE_SIZE = 128 * 1024
+ option CONFIG_XIP_ROM_SIZE = 256 * 1024
option COREBOOT_EXTRA_VERSION = ".0Normal"
# payload /tmp/filo.elf
payload ../payload.elf
end
romimage "fallback"
- option USE_FAILOVER_IMAGE = 0
- option USE_FALLBACK_IMAGE = 1
- option ROM_IMAGE_SIZE = 128 * 1024
- option XIP_ROM_SIZE = 256 * 1024
+ option CONFIG_USE_FAILOVER_IMAGE = 0
+ option CONFIG_USE_FALLBACK_IMAGE = 1
+ option CONFIG_ROM_IMAGE_SIZE = 128 * 1024
+ option CONFIG_XIP_ROM_SIZE = 256 * 1024
option COREBOOT_EXTRA_VERSION = ".0Fallback"
# payload /tmp/filo.elf
payload ../payload.elf
end
romimage "failover"
- option USE_FAILOVER_IMAGE = 1
- option USE_FALLBACK_IMAGE = 0
- option ROM_IMAGE_SIZE = FAILOVER_SIZE
- option XIP_ROM_SIZE = FAILOVER_SIZE
+ option CONFIG_USE_FAILOVER_IMAGE = 1
+ option CONFIG_USE_FALLBACK_IMAGE = 0
+ option CONFIG_ROM_IMAGE_SIZE = CONFIG_FAILOVER_SIZE
+ option CONFIG_XIP_ROM_SIZE = CONFIG_FAILOVER_SIZE
option COREBOOT_EXTRA_VERSION = ".0Failover"
end
-# buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback" "failover"
+# buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback" "failover"
mainboard VENDOR/MAINBOARD
option CC="CROSSCC"
-option CROSS_COMPILE="CROSS_PREFIX"
-option HOSTCC="CROSS_HOSTCC"
+option CONFIG_CROSS_COMPILE="CROSS_PREFIX"
+option CONFIG_HOSTCC="CROSS_HOSTCC"
__COMPRESSION__
__LOGLEVEL__
romimage "normal"
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE = 128 * 1024
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE = 128 * 1024
option COREBOOT_EXTRA_VERSION=".0-normal"
payload __PAYLOAD__
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE = 128 * 1024
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE = 128 * 1024
option COREBOOT_EXTRA_VERSION=".0-fallback"
payload __PAYLOAD__
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
# ms9185
romimage "normal"
# 36k for ATI option rom
- option ROM_SIZE = 512*1024-36*1024
-# option ROM_SIZE = 524288
-# option ROM_SIZE = 425984
+ option CONFIG_ROM_SIZE = 512*1024-36*1024
+# option CONFIG_ROM_SIZE = 524288
+# option CONFIG_ROM_SIZE = 425984
# 64K for Etherboot
-# option ROM_SIZE = 458752
- option USE_FALLBACK_IMAGE=0
-# option ROM_IMAGE_SIZE=0x13800
-# option ROM_IMAGE_SIZE=0x18800
- option ROM_IMAGE_SIZE=0x20000
-# option ROM_IMAGE_SIZE=0x15800
- option XIP_ROM_SIZE=0x40000
+# option CONFIG_ROM_SIZE = 458752
+ option CONFIG_USE_FALLBACK_IMAGE=0
+# option CONFIG_ROM_IMAGE_SIZE=0x13800
+# option CONFIG_ROM_IMAGE_SIZE=0x18800
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+# option CONFIG_ROM_IMAGE_SIZE=0x15800
+ option CONFIG_XIP_ROM_SIZE=0x40000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Normal"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
-# option ROM_IMAGE_SIZE=0x13800
-# option ROM_IMAGE_SIZE=0x19800
- option ROM_IMAGE_SIZE=0x20000
-# option ROM_IMAGE_SIZE=0x15800
- option XIP_ROM_SIZE=0x40000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+# option CONFIG_ROM_IMAGE_SIZE=0x13800
+# option CONFIG_ROM_IMAGE_SIZE=0x19800
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+# option CONFIG_ROM_IMAGE_SIZE=0x15800
+ option CONFIG_XIP_ROM_SIZE=0x40000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
# payload ../../../payloads/tg3--eepro100--e1000--filo_hda2_com2.zelf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
mainboard VENDOR/MAINBOARD
option CC="CROSSCC"
-option CROSS_COMPILE="CROSS_PREFIX"
-option HOSTCC="CROSS_HOSTCC"
+option CONFIG_CROSS_COMPILE="CROSS_PREFIX"
+option CONFIG_HOSTCC="CROSS_HOSTCC"
__COMPRESSION__
__LOGLEVEL__
romimage "normal"
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE = 128 * 1024
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE = 128 * 1024
option COREBOOT_EXTRA_VERSION=".0-normal"
payload __PAYLOAD__
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE = 128 * 1024
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE = 128 * 1024
option COREBOOT_EXTRA_VERSION=".0-fallback"
payload __PAYLOAD__
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
romimage "normal"
# 48K for SCSI FW
-# option ROM_SIZE = 475136
- option ROM_SIZE = 512*1024-36*1024
-# option ROM_SIZE = 524288
+# option CONFIG_ROM_SIZE = 475136
+ option CONFIG_ROM_SIZE = 512*1024-36*1024
+# option CONFIG_ROM_SIZE = 524288
# 48K for SCSI FW and 48K for ATI ROM
-# option ROM_SIZE = 425984
+# option CONFIG_ROM_SIZE = 425984
# 64K for Etherboot
-# option ROM_SIZE = 458752
- option USE_FALLBACK_IMAGE=0
-# option ROM_IMAGE_SIZE=0x13800
-# option ROM_IMAGE_SIZE=0x18800
- option ROM_IMAGE_SIZE=0x20000
-# option ROM_IMAGE_SIZE=0x15800
- option XIP_ROM_SIZE=0x40000
+# option CONFIG_ROM_SIZE = 458752
+ option CONFIG_USE_FALLBACK_IMAGE=0
+# option CONFIG_ROM_IMAGE_SIZE=0x13800
+# option CONFIG_ROM_IMAGE_SIZE=0x18800
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+# option CONFIG_ROM_IMAGE_SIZE=0x15800
+ option CONFIG_XIP_ROM_SIZE=0x40000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Normal"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
-# option ROM_IMAGE_SIZE=0x13800
-# option ROM_IMAGE_SIZE=0x19800
- option ROM_IMAGE_SIZE=0x20000
-# option ROM_IMAGE_SIZE=0x15800
- option XIP_ROM_SIZE=0x40000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+# option CONFIG_ROM_IMAGE_SIZE=0x13800
+# option CONFIG_ROM_IMAGE_SIZE=0x19800
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+# option CONFIG_ROM_IMAGE_SIZE=0x15800
+ option CONFIG_XIP_ROM_SIZE=0x40000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
# payload ../../../payloads/tg3--eepro100--e1000--filo_hda2_com2.zelf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
target powermate2000
mainboard nec/powermate2000
-option ROM_SIZE = 512 * 1024
+option CONFIG_ROM_SIZE = 512 * 1024
-option MAINBOARD_VENDOR = "NEC"
-option MAINBOARD_PART_NUMBER = "PowerMate 2000"
+option CONFIG_MAINBOARD_VENDOR = "NEC"
+option CONFIG_MAINBOARD_PART_NUMBER = "PowerMate 2000"
-option IRQ_SLOT_COUNT = 5
+option CONFIG_IRQ_SLOT_COUNT = 5
-option DEFAULT_CONSOLE_LOGLEVEL = 9
-option MAXIMUM_CONSOLE_LOGLEVEL = 9
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
option CONFIG_CONSOLE_VGA = 1
option CONFIG_PCI_ROM_RUN = 1
romimage "normal"
- option USE_FALLBACK_IMAGE = 0
+ option CONFIG_USE_FALLBACK_IMAGE = 0
option COREBOOT_EXTRA_VERSION = ".0Normal"
payload ../payload.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE = 1
+ option CONFIG_USE_FALLBACK_IMAGE = 1
option COREBOOT_EXTRA_VERSION = ".0Fallback"
payload ../payload.elf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
# Configuration options.
-option MAXIMUM_CONSOLE_LOGLEVEL=8
-option DEFAULT_CONSOLE_LOGLEVEL=8
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
option CONFIG_CONSOLE_SERIAL8250=1
# Size of the image. Khepri comes with 512k per default.
-option ROM_SIZE=512*1024
+option CONFIG_ROM_SIZE=512*1024
-option HAVE_OPTION_TABLE=1
+option CONFIG_HAVE_OPTION_TABLE=1
option CONFIG_ROM_PAYLOAD=1
-option HAVE_FALLBACK_BOOT=1
+option CONFIG_HAVE_FALLBACK_BOOT=1
-option FALLBACK_SIZE=131072
+option CONFIG_FALLBACK_SIZE=131072
## Coreboot C code runs at this location in RAM
-option _RAMBASE=0x00004000
+option CONFIG_RAMBASE=0x00004000
romimage "normal"
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=0x20000
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
option COREBOOT_EXTRA_VERSION="-Khepri-Normal"
payload ../../../payloads/tg3--ide_disk.zelf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x20000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
option COREBOOT_EXTRA_VERSION="-Khepri-Fallback"
payload ../../../payloads/tg3--ide_disk.zelf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
mainboard VENDOR/MAINBOARD
option CC="CROSSCC"
-option CROSS_COMPILE="CROSS_PREFIX"
-option HOSTCC="CROSS_HOSTCC"
+option CONFIG_CROSS_COMPILE="CROSS_PREFIX"
+option CONFIG_HOSTCC="CROSS_HOSTCC"
__COMPRESSION__
__LOGLEVEL__
romimage "normal"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=0x20000
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
option COREBOOT_EXTRA_VERSION=".0-normal"
payload __PAYLOAD__
end
romimage "fallback"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x20000
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
option COREBOOT_EXTRA_VERSION=".0-fallback"
payload __PAYLOAD__
end
romimage "failover"
- option USE_FAILOVER_IMAGE=1
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=FAILOVER_SIZE
- option XIP_ROM_SIZE=FAILOVER_SIZE
+ option CONFIG_USE_FAILOVER_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=CONFIG_FAILOVER_SIZE
+ option CONFIG_XIP_ROM_SIZE=CONFIG_FAILOVER_SIZE
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback" "failover"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback" "failover"
# serengeti_leopard
romimage "normal"
# 48K for SCSI FW
-# option ROM_SIZE = 475136
+# option CONFIG_ROM_SIZE = 475136
# 48K for SCSI FW and 48K for ATI ROM
-# option ROM_SIZE = 425984
+# option CONFIG_ROM_SIZE = 425984
# 64K for Etherboot
-# option ROM_SIZE = 458752
+# option CONFIG_ROM_SIZE = 458752
# 44k for atixx.rom
-# option ROM_SIZE = 479232
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=0
-# option ROM_IMAGE_SIZE=0x13800
-# option ROM_IMAGE_SIZE=0x18800
- option ROM_IMAGE_SIZE=0x20000
-# option ROM_IMAGE_SIZE=0x15800
- option XIP_ROM_SIZE=0x40000
+# option CONFIG_ROM_SIZE = 479232
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=0
+# option CONFIG_ROM_IMAGE_SIZE=0x13800
+# option CONFIG_ROM_IMAGE_SIZE=0x18800
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+# option CONFIG_ROM_IMAGE_SIZE=0x15800
+ option CONFIG_XIP_ROM_SIZE=0x40000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Normal"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
end
romimage "fallback"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=1
-# option ROM_IMAGE_SIZE=0x13800
-# option ROM_IMAGE_SIZE=0x19800
- option ROM_IMAGE_SIZE=0x20000
-# option ROM_IMAGE_SIZE=0x15800
- option XIP_ROM_SIZE=0x40000
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=1
+# option CONFIG_ROM_IMAGE_SIZE=0x13800
+# option CONFIG_ROM_IMAGE_SIZE=0x19800
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+# option CONFIG_ROM_IMAGE_SIZE=0x15800
+ option CONFIG_XIP_ROM_SIZE=0x40000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
end
romimage "failover"
- option USE_FAILOVER_IMAGE=1
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=FAILOVER_SIZE
- option XIP_ROM_SIZE=FAILOVER_SIZE
+ option CONFIG_USE_FAILOVER_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=CONFIG_FAILOVER_SIZE
+ option CONFIG_XIP_ROM_SIZE=CONFIG_FAILOVER_SIZE
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Failover"
end
-#buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback" "failover"
+#buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback" "failover"
target l1_2pvv
mainboard nvidia/l1_2pvv
-option ROM_SIZE=0x200000
-option FALLBACK_SIZE=(ROM_SIZE-0x1000)
+option CONFIG_ROM_SIZE=0x200000
+option CONFIG_FALLBACK_SIZE=(CONFIG_ROM_SIZE-0x1000)
romimage "fallback"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=1
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=1
option CONFIG_COMPRESSED_PAYLOAD_LZMA=1
option CONFIG_PRECOMPRESSED_PAYLOAD=1
-# option ROM_IMAGE_SIZE=0x19800
- option ROM_IMAGE_SIZE=0x17000
-# option ROM_IMAGE_SIZE=0x15800
-# option ROM_IMAGE_SIZE=0x13800
- option XIP_ROM_SIZE=0x40000
+# option CONFIG_ROM_IMAGE_SIZE=0x19800
+ option CONFIG_ROM_IMAGE_SIZE=0x17000
+# option CONFIG_ROM_IMAGE_SIZE=0x15800
+# option CONFIG_ROM_IMAGE_SIZE=0x13800
+ option CONFIG_XIP_ROM_SIZE=0x40000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
end
romimage "failover"
- option USE_FAILOVER_IMAGE=1
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=FAILOVER_SIZE
- option XIP_ROM_SIZE=FAILOVER_SIZE
+ option CONFIG_USE_FAILOVER_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=CONFIG_FAILOVER_SIZE
+ option CONFIG_XIP_ROM_SIZE=CONFIG_FAILOVER_SIZE
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Failover"
end
-buildrom ./coreboot.rom ROM_SIZE "fallback" "failover"
-#buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback" "failover"
+#buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
#option CONFIG_PRECOMPRESSED_PAYLOAD=0
# leave 64k for vsa and 64k for EC code
-option ROM_SIZE=(1024*1024)-(64*1024)-(64*1024)
-option FALLBACK_SIZE=ROM_SIZE
+option CONFIG_ROM_SIZE=(1024*1024)-(64*1024)-(64*1024)
+option CONFIG_FALLBACK_SIZE=CONFIG_ROM_SIZE
-option DEFAULT_CONSOLE_LOGLEVEL = 3
-option MAXIMUM_CONSOLE_LOGLEVEL = 3
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 3
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 3
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=32*1024
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=32*1024
option COREBOOT_EXTRA_VERSION=".0Fallback"
payload /tmp/olpcpayload.elf
end
-buildrom ./coreboot.rom ROM_SIZE "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback"
#option CONFIG_PRECOMPRESSED_PAYLOAD=1
# leave 64k for vsa
-option ROM_SIZE=(1024*1024)-(64*1024)
-option FALLBACK_SIZE=ROM_SIZE
+option CONFIG_ROM_SIZE=(1024*1024)-(64*1024)
+option CONFIG_FALLBACK_SIZE=CONFIG_ROM_SIZE
-option DEFAULT_CONSOLE_LOGLEVEL = 9
-option MAXIMUM_CONSOLE_LOGLEVEL = 9
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=32*1024
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=32*1024
option COREBOOT_EXTRA_VERSION=".0Fallback"
payload /tmp/olpcpayload.elf
end
-buildrom ./coreboot.rom ROM_SIZE "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback"
#option CONFIG_PRECOMPRESSED_PAYLOAD=0
# leave 64k for vsa and 64k for EC code
-option ROM_SIZE=(1024*1024)-(64*1024)-(64*1024)
-option FALLBACK_SIZE=ROM_SIZE
+option CONFIG_ROM_SIZE=(1024*1024)-(64*1024)-(64*1024)
+option CONFIG_FALLBACK_SIZE=CONFIG_ROM_SIZE
-option DEFAULT_CONSOLE_LOGLEVEL = 9
-option MAXIMUM_CONSOLE_LOGLEVEL = 9
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=32*1024
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=32*1024
option COREBOOT_EXTRA_VERSION=".0Fallback"
payload /tmp/olpcpayload.elf
end
-buildrom ./coreboot.rom ROM_SIZE "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback"
target rev_a
mainboard olpc/rev_a
-option ROM_SIZE=7*128*1024
-option FALLBACK_SIZE=ROM_SIZE
+option CONFIG_ROM_SIZE=7*128*1024
+option CONFIG_FALLBACK_SIZE=CONFIG_ROM_SIZE
#romimage "normal"
-# option USE_FALLBACK_IMAGE=0
-# option ROM_IMAGE_SIZE=0x10000
+# option CONFIG_USE_FALLBACK_IMAGE=0
+# option CONFIG_ROM_IMAGE_SIZE=0x10000
# option COREBOOT_EXTRA_VERSION=".0Normal"
## payload /usr/share/etherboot/5.1.9pre2-lnxi-lb/tg3--ide_disk.zelf
## payload ../../../../tg3--ide_disk.zelf
#end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x10000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x10000
option COREBOOT_EXTRA_VERSION=".0Fallback"
# payload /usr/share/etherboot/5.1.9pre2-lnxi-lb/tg3--ide_disk.zelf
# payload ../../../../tg3--ide_disk.zelf
payload /tmp/olpc
end
-buildrom ./coreboot.rom ROM_SIZE "fallback"
-#buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback"
+#buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
# leave 64k for vsa
option CONFIG_COMPRESSED_PAYLOAD_NRV2B=0
-option ROM_SIZE=512*1024-64*1024
-option FALLBACK_SIZE=ROM_SIZE
+option CONFIG_ROM_SIZE=512*1024-64*1024
+option CONFIG_FALLBACK_SIZE=CONFIG_ROM_SIZE
-option DEFAULT_CONSOLE_LOGLEVEL = 9
-option MAXIMUM_CONSOLE_LOGLEVEL = 9
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=32*1024
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=32*1024
option COREBOOT_EXTRA_VERSION=".0Fallback"
payload /tmp/olpcpayload.elf
end
-buildrom ./coreboot.rom ROM_SIZE "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback"
option CONFIG_COMPRESSED_PAYLOAD_NRV2B=0
-## ROM_SIZE is the total number of bytes allocated for coreboot use
+## CONFIG_ROM_SIZE is the total number of bytes allocated for coreboot use
## (normal AND fallback images and payloads). Leave 36k for VSA.
-option ROM_SIZE = (512 * 1024) - (36 * 1024)
+option CONFIG_ROM_SIZE = (512 * 1024) - (36 * 1024)
-## ROM_IMAGE_SIZE is the maximum number of bytes allowed for a coreboot image,
+## CONFIG_ROM_IMAGE_SIZE is the maximum number of bytes allowed for a coreboot image,
## not including any payload.
-option ROM_IMAGE_SIZE = (64 * 1024)
+option CONFIG_ROM_IMAGE_SIZE = (64 * 1024)
-option FALLBACK_SIZE = ROM_SIZE
+option CONFIG_FALLBACK_SIZE = CONFIG_ROM_SIZE
-option DEFAULT_CONSOLE_LOGLEVEL = 3
-option MAXIMUM_CONSOLE_LOGLEVEL = 9
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 3
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
romimage "fallback"
- option USE_FALLBACK_IMAGE = 1
+ option CONFIG_USE_FALLBACK_IMAGE = 1
option COREBOOT_EXTRA_VERSION = ".0Fallback"
payload ../payload.elf
end
-buildrom ./coreboot.rom ROM_SIZE "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback"
mainboard VENDOR/MAINBOARD
option CC="CROSSCC"
-option CROSS_COMPILE="CROSS_PREFIX"
-option HOSTCC="CROSS_HOSTCC"
+option CONFIG_CROSS_COMPILE="CROSS_PREFIX"
+option CONFIG_HOSTCC="CROSS_HOSTCC"
__COMPRESSION__
__LOGLEVEL__
romimage "fallback"
- option USE_FALLBACK_IMAGE = 1
+ option CONFIG_USE_FALLBACK_IMAGE = 1
payload __PAYLOAD__
end
-buildrom ./coreboot.rom ROM_SIZE "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback"
## Total number of bytes allocated for coreboot use
## (fallback images and payloads).
##
-# option ROM_SIZE = 1024 * 1024
+# option CONFIG_ROM_SIZE = 1024 * 1024
## For VGA BIOS (-64k)
-option ROM_SIZE = (1024 * 1024) - (64 * 1024)
+option CONFIG_ROM_SIZE = (1024 * 1024) - (64 * 1024)
##
## VGA Console
##
## Request this level of debugging output
##
-option DEFAULT_CONSOLE_LOGLEVEL = 7
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 7
romimage "fallback"
- option USE_FALLBACK_IMAGE = 1
- option FALLBACK_SIZE = ROM_SIZE
+ option CONFIG_USE_FALLBACK_IMAGE = 1
+ option CONFIG_FALLBACK_SIZE = CONFIG_ROM_SIZE
option COREBOOT_EXTRA_VERSION = "_RM4100"
payload /tmp/filo.elf
# payload /tmp/eb-5.4.3-eepro100.elf
end
-buildrom ./coreboot.rom ROM_SIZE "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback"
target sy-6ba-plus-iii
mainboard soyo/sy-6ba-plus-iii
-option ROM_SIZE = 256 * 1024
-# option FALLBACK_SIZE = ROM_SIZE
+option CONFIG_ROM_SIZE = 256 * 1024
+# option CONFIG_FALLBACK_SIZE = CONFIG_ROM_SIZE
-option MAINBOARD_VENDOR = "Soyo"
-option MAINBOARD_PART_NUMBER = "SY-6BA+ III"
+option CONFIG_MAINBOARD_VENDOR = "Soyo"
+option CONFIG_MAINBOARD_PART_NUMBER = "SY-6BA+ III"
-option IRQ_SLOT_COUNT = 7
+option CONFIG_IRQ_SLOT_COUNT = 7
-option DEFAULT_CONSOLE_LOGLEVEL = 9
-option MAXIMUM_CONSOLE_LOGLEVEL = 9
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
option CONFIG_CONSOLE_VGA = 1
option CONFIG_PCI_ROM_RUN = 1
romimage "normal"
- option USE_FALLBACK_IMAGE = 0
+ option CONFIG_USE_FALLBACK_IMAGE = 0
option COREBOOT_EXTRA_VERSION = ".0Normal"
payload ../payload.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE = 1
+ option CONFIG_USE_FALLBACK_IMAGE = 1
option COREBOOT_EXTRA_VERSION = ".0Fallback"
payload ../payload.elf
end
-# buildrom ./coreboot.rom ROM_SIZE "fallback"
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+# buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
target ultra40
mainboard sunw/ultra40
-option ROM_SIZE=512*1024
+option CONFIG_ROM_SIZE=512*1024
# sunw ultra40
romimage "normal"
# 48K for SCSI FW
-# option ROM_SIZE = 512*1024-48*1024
+# option CONFIG_ROM_SIZE = 512*1024-48*1024
# 48K for SCSI FW and 48K for ATI ROM
-# option ROM_SIZE = 512*1024-48*1024-48*1024
+# option CONFIG_ROM_SIZE = 512*1024-48*1024-48*1024
# 64K for Etherboot
-# option ROM_SIZE = 512*1024-64*1024
+# option CONFIG_ROM_SIZE = 512*1024-64*1024
# 64K for NIC option 48K for Raid option rom
-# option ROM_SIZE = 512*1024-64*1024-48*1024
- option USE_FALLBACK_IMAGE=0
-# option ROM_IMAGE_SIZE=0x11800
-# option ROM_IMAGE_SIZE=0x13800
-# option ROM_IMAGE_SIZE=0x15000
- option ROM_IMAGE_SIZE=0x20000
-# option ROM_IMAGE_SIZE=0x17800
- option XIP_ROM_SIZE=0x20000
+# option CONFIG_ROM_SIZE = 512*1024-64*1024-48*1024
+ option CONFIG_USE_FALLBACK_IMAGE=0
+# option CONFIG_ROM_IMAGE_SIZE=0x11800
+# option CONFIG_ROM_IMAGE_SIZE=0x13800
+# option CONFIG_ROM_IMAGE_SIZE=0x15000
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+# option CONFIG_ROM_IMAGE_SIZE=0x17800
+ option CONFIG_XIP_ROM_SIZE=0x20000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Normal"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
-# option ROM_IMAGE_SIZE=0x11800
-# option ROM_IMAGE_SIZE=0x13800
-# option ROM_IMAGE_SIZE=0x15000
- option ROM_IMAGE_SIZE=0x20000
-# option ROM_IMAGE_SIZE=0x17800
- option XIP_ROM_SIZE=0x20000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+# option CONFIG_ROM_IMAGE_SIZE=0x11800
+# option CONFIG_ROM_IMAGE_SIZE=0x13800
+# option CONFIG_ROM_IMAGE_SIZE=0x15000
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+# option CONFIG_ROM_IMAGE_SIZE=0x17800
+ option CONFIG_XIP_ROM_SIZE=0x20000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
# payload ../../../payloads/tg3--eepro100--e1000--filo_hda2.zelf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
mainboard VENDOR/MAINBOARD
option CC="CROSSCC"
-option CROSS_COMPILE="CROSS_PREFIX"
-option HOSTCC="CROSS_HOSTCC"
+option CONFIG_CROSS_COMPILE="CROSS_PREFIX"
+option CONFIG_HOSTCC="CROSS_HOSTCC"
__COMPRESSION__
__LOGLEVEL__
romimage "normal"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=0x20000
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
option COREBOOT_EXTRA_VERSION=".0-normal"
payload __PAYLOAD__
end
romimage "fallback"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x20000
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
option COREBOOT_EXTRA_VERSION=".0-fallback"
payload __PAYLOAD__
end
romimage "failover"
- option USE_FAILOVER_IMAGE=1
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=FAILOVER_SIZE
- option XIP_ROM_SIZE=FAILOVER_SIZE
+ option CONFIG_USE_FAILOVER_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=CONFIG_FAILOVER_SIZE
+ option CONFIG_XIP_ROM_SIZE=CONFIG_FAILOVER_SIZE
option COREBOOT_EXTRA_VERSION=".0-failover"
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback" "failover"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback" "failover"
target h8dmre
mainboard supermicro/h8dme
-option ROM_SIZE=0x100000
+option CONFIG_ROM_SIZE=0x100000
# 44K for ATI ROM in 1M; 4K for failover
-option FALLBACK_SIZE=(ROM_SIZE-0xC000)
+option CONFIG_FALLBACK_SIZE=(CONFIG_ROM_SIZE-0xC000)
romimage "fallback"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=1
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=1
option CONFIG_COMPRESSED_PAYLOAD_LZMA=1
option CONFIG_PRECOMPRESSED_PAYLOAD=1
- option ROM_IMAGE_SIZE=0x18000
- option XIP_ROM_SIZE=0x40000
+ option CONFIG_ROM_IMAGE_SIZE=0x18000
+ option CONFIG_XIP_ROM_SIZE=0x40000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
payload ../payload.elf.lzma
end
romimage "failover"
- option USE_FAILOVER_IMAGE=1
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=FAILOVER_SIZE
- option XIP_ROM_SIZE=FAILOVER_SIZE
+ option CONFIG_USE_FAILOVER_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=CONFIG_FAILOVER_SIZE
+ option CONFIG_XIP_ROM_SIZE=CONFIG_FAILOVER_SIZE
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Failover"
end
-buildrom ./coreboot.rom ROM_SIZE "fallback" "failover"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback" "failover"
mainboard supermicro/h8dme
romimage "normal"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=0x20000
- option XIP_ROM_SIZE=0x40000
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+ option CONFIG_XIP_ROM_SIZE=0x40000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Normal"
payload ../payload.elf
end
romimage "fallback"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x20000
- option XIP_ROM_SIZE=0x40000
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+ option CONFIG_XIP_ROM_SIZE=0x40000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
payload ../payload.elf
end
romimage "failover"
- option USE_FAILOVER_IMAGE=1
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=FAILOVER_SIZE
- option XIP_ROM_SIZE=FAILOVER_SIZE
+ option CONFIG_USE_FAILOVER_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=CONFIG_FAILOVER_SIZE
+ option CONFIG_XIP_ROM_SIZE=CONFIG_FAILOVER_SIZE
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Failover"
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback" "failover"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback" "failover"
target h8dme
mainboard supermicro/h8dme
-option ROM_SIZE=0x200000
-option FALLBACK_SIZE=(ROM_SIZE-0x1000)
+option CONFIG_ROM_SIZE=0x200000
+option CONFIG_FALLBACK_SIZE=(CONFIG_ROM_SIZE-0x1000)
romimage "fallback"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=1
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=1
option CONFIG_COMPRESSED_PAYLOAD_LZMA=1
option CONFIG_PRECOMPRESSED_PAYLOAD=1
- option ROM_IMAGE_SIZE=0x18000
- option XIP_ROM_SIZE=0x40000
+ option CONFIG_ROM_IMAGE_SIZE=0x18000
+ option CONFIG_XIP_ROM_SIZE=0x40000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
end
romimage "failover"
- option USE_FAILOVER_IMAGE=1
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=FAILOVER_SIZE
- option XIP_ROM_SIZE=FAILOVER_SIZE
+ option CONFIG_USE_FAILOVER_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=CONFIG_FAILOVER_SIZE
+ option CONFIG_XIP_ROM_SIZE=CONFIG_FAILOVER_SIZE
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Failover"
end
-buildrom ./coreboot.rom ROM_SIZE "fallback" "failover"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback" "failover"
mainboard VENDOR/MAINBOARD
option CC="CROSSCC"
-option CROSS_COMPILE="CROSS_PREFIX"
-option HOSTCC="CROSS_HOSTCC"
+option CONFIG_CROSS_COMPILE="CROSS_PREFIX"
+option CONFIG_HOSTCC="CROSS_HOSTCC"
__COMPRESSION__
__LOGLEVEL__
romimage "normal"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=0x20000
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
option COREBOOT_EXTRA_VERSION=".0-normal"
payload __PAYLOAD__
end
romimage "fallback"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x20000
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
option COREBOOT_EXTRA_VERSION=".0-fallback"
payload __PAYLOAD__
end
romimage "failover"
- option USE_FAILOVER_IMAGE=1
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=FAILOVER_SIZE
- option XIP_ROM_SIZE=FAILOVER_SIZE
+ option CONFIG_USE_FAILOVER_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=CONFIG_FAILOVER_SIZE
+ option CONFIG_XIP_ROM_SIZE=CONFIG_FAILOVER_SIZE
option COREBOOT_EXTRA_VERSION=".0-failover"
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback" "failover"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback" "failover"
target h8dmr
mainboard supermicro/h8dmr
-option ROM_SIZE=0x100000
+option CONFIG_ROM_SIZE=0x100000
# 44K for ATI ROM in 1M; 4K for failover
-option FALLBACK_SIZE=(ROM_SIZE-0xC000)
+option CONFIG_FALLBACK_SIZE=(CONFIG_ROM_SIZE-0xC000)
romimage "fallback"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=1
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=1
option CONFIG_COMPRESSED_PAYLOAD_LZMA=1
option CONFIG_PRECOMPRESSED_PAYLOAD=1
- option ROM_IMAGE_SIZE=0x18000
- option XIP_ROM_SIZE=0x40000
+ option CONFIG_ROM_IMAGE_SIZE=0x18000
+ option CONFIG_XIP_ROM_SIZE=0x40000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
payload ../payload.elf.lzma
end
romimage "failover"
- option USE_FAILOVER_IMAGE=1
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=FAILOVER_SIZE
- option XIP_ROM_SIZE=FAILOVER_SIZE
+ option CONFIG_USE_FAILOVER_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=CONFIG_FAILOVER_SIZE
+ option CONFIG_XIP_ROM_SIZE=CONFIG_FAILOVER_SIZE
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Failover"
end
-buildrom ./coreboot.rom ROM_SIZE "fallback" "failover"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback" "failover"
romimage "normal"
# 48K for SCSI FW
-# option ROM_SIZE = 475136
+# option CONFIG_ROM_SIZE = 475136
# 48K for SCSI FW and 48K for ATI ROM
-# option ROM_SIZE = 425984
+# option CONFIG_ROM_SIZE = 425984
# 64K for Etherboot
-# option ROM_SIZE = 458752
+# option CONFIG_ROM_SIZE = 458752
# 44k for atixx.rom
-# option ROM_SIZE = 479232
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=0
-# option ROM_IMAGE_SIZE=0x13800
-# option ROM_IMAGE_SIZE=0x18800
- option ROM_IMAGE_SIZE=0x20000
-# option ROM_IMAGE_SIZE=0x15800
- option XIP_ROM_SIZE=0x40000
+# option CONFIG_ROM_SIZE = 479232
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=0
+# option CONFIG_ROM_IMAGE_SIZE=0x13800
+# option CONFIG_ROM_IMAGE_SIZE=0x18800
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+# option CONFIG_ROM_IMAGE_SIZE=0x15800
+ option CONFIG_XIP_ROM_SIZE=0x40000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Normal"
payload ../payload.elf
end
romimage "fallback"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=1
-# option ROM_IMAGE_SIZE=0x13800
-# option ROM_IMAGE_SIZE=0x19800
- option ROM_IMAGE_SIZE=0x20000
-# option ROM_IMAGE_SIZE=0x15800
- option XIP_ROM_SIZE=0x40000
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=1
+# option CONFIG_ROM_IMAGE_SIZE=0x13800
+# option CONFIG_ROM_IMAGE_SIZE=0x19800
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+# option CONFIG_ROM_IMAGE_SIZE=0x15800
+ option CONFIG_XIP_ROM_SIZE=0x40000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
payload ../payload.elf
end
romimage "failover"
- option USE_FAILOVER_IMAGE=1
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=FAILOVER_SIZE
- option XIP_ROM_SIZE=FAILOVER_SIZE
+ option CONFIG_USE_FAILOVER_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=CONFIG_FAILOVER_SIZE
+ option CONFIG_XIP_ROM_SIZE=CONFIG_FAILOVER_SIZE
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Failover"
end
-#buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback" "failover"
+#buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback" "failover"
target h8dmr
mainboard supermicro/h8dmr
-option ROM_SIZE=0x200000
-option FALLBACK_SIZE=(ROM_SIZE-0x1000)
+option CONFIG_ROM_SIZE=0x200000
+option CONFIG_FALLBACK_SIZE=(CONFIG_ROM_SIZE-0x1000)
romimage "fallback"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=1
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=1
option CONFIG_COMPRESSED_PAYLOAD_LZMA=1
option CONFIG_PRECOMPRESSED_PAYLOAD=1
-# option ROM_IMAGE_SIZE=0x19800
- option ROM_IMAGE_SIZE=0x18000
-# option ROM_IMAGE_SIZE=0x15800
-# option ROM_IMAGE_SIZE=0x13800
- option XIP_ROM_SIZE=0x40000
+# option CONFIG_ROM_IMAGE_SIZE=0x19800
+ option CONFIG_ROM_IMAGE_SIZE=0x18000
+# option CONFIG_ROM_IMAGE_SIZE=0x15800
+# option CONFIG_ROM_IMAGE_SIZE=0x13800
+ option CONFIG_XIP_ROM_SIZE=0x40000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
end
romimage "failover"
- option USE_FAILOVER_IMAGE=1
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=FAILOVER_SIZE
- option XIP_ROM_SIZE=FAILOVER_SIZE
+ option CONFIG_USE_FAILOVER_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=CONFIG_FAILOVER_SIZE
+ option CONFIG_XIP_ROM_SIZE=CONFIG_FAILOVER_SIZE
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Failover"
end
-buildrom ./coreboot.rom ROM_SIZE "fallback" "failover"
-#buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback" "failover"
+#buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
mainboard VENDOR/MAINBOARD
option CC="CROSSCC"
-option CROSS_COMPILE="CROSS_PREFIX"
-option HOSTCC="CROSS_HOSTCC"
+option CONFIG_CROSS_COMPILE="CROSS_PREFIX"
+option CONFIG_HOSTCC="CROSS_HOSTCC"
__COMPRESSION__
__LOGLEVEL__
romimage "normal"
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=0x20000
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
option COREBOOT_EXTRA_VERSION=".0-normal"
payload __PAYLOAD__
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x20000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
option COREBOOT_EXTRA_VERSION=".0-fallback"
payload __PAYLOAD__
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
romimage "normal"
- option ROM_SIZE = 1024*512 - 55808
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=0x20000
- option XIP_ROM_SIZE=0x20000
+ option CONFIG_ROM_SIZE = 1024*512 - 55808
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+ option CONFIG_XIP_ROM_SIZE=0x20000
payload /home/daniel/mypayloads/link
end
romimage "fallback"
- option FALLBACK_SIZE= 1024*512 - 55808
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x20000
- option XIP_ROM_SIZE=0x20000
+ option CONFIG_FALLBACK_SIZE= 1024*512 - 55808
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+ option CONFIG_XIP_ROM_SIZE=0x20000
payload /home/daniel/mypayloads/link
end
-buildrom ./coreboot.rom ROM_SIZE "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback"
mainboard VENDOR/MAINBOARD
option CC="CROSSCC"
-option CROSS_COMPILE="CROSS_PREFIX"
-option HOSTCC="CROSS_HOSTCC"
+option CONFIG_CROSS_COMPILE="CROSS_PREFIX"
+option CONFIG_HOSTCC="CROSS_HOSTCC"
__COMPRESSION__
__LOGLEVEL__
romimage "fallback"
- option FALLBACK_SIZE = 256 * 1024
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=128 * 1024 # 0x10000
+ option CONFIG_FALLBACK_SIZE = 256 * 1024
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=128 * 1024 # 0x10000
option COREBOOT_EXTRA_VERSION=".0-Fallback"
payload __PAYLOAD__
end
-buildrom ./coreboot.rom ROM_SIZE "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback"
target technologic_ts5300
mainboard technologic/ts5300
-option DEFAULT_CONSOLE_LOGLEVEL=3
-option MAXIMUM_CONSOLE_LOGLEVEL=3
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL=3
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=3
option CONFIG_COMPRESS=1
#romimage "normal"
-# option USE_FALLBACK_IMAGE=0
-# option ROM_IMAGE_SIZE=0x10000
+# option CONFIG_USE_FALLBACK_IMAGE=0
+# option CONFIG_ROM_IMAGE_SIZE=0x10000
# option COREBOOT_EXTRA_VERSION=".0-Normal"
# payload /etc/hosts
#end
romimage "fallback"
- option FALLBACK_SIZE = 128 * 1024
-# option ROM_SIZE=512*1024
-# option ROM_SECTION_SIZE=512*1024
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=32 * 1024 # 0x8000
-# option ROM_IMAGE_SIZE=48 * 1024 # 0x8000
-# option ROM_IMAGE_SIZE=64 * 1024 # 0x10000
-# option ROM_IMAGE_SIZE=512 * 1024 # 0x10000
+ option CONFIG_FALLBACK_SIZE = 128 * 1024
+# option CONFIG_ROM_SIZE=512*1024
+# option CONFIG_ROM_SECTION_SIZE=512*1024
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=32 * 1024 # 0x8000
+# option CONFIG_ROM_IMAGE_SIZE=48 * 1024 # 0x8000
+# option CONFIG_ROM_IMAGE_SIZE=64 * 1024 # 0x10000
+# option CONFIG_ROM_IMAGE_SIZE=512 * 1024 # 0x10000
# option COREBOOT_EXTRA_VERSION=".0-Fallback"
option COREBOOT_EXTRA_VERSION=".0"
payload /home/stepan/filo-ts5300.elf
end
-buildrom ./coreboot.rom ROM_SIZE "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback"
target tc7020
mainboard televideo/tc7020
-option ROM_SIZE = 256 * 1024
+option CONFIG_ROM_SIZE = 256 * 1024
## Enable VGA with a splash screen (only 640x480 to run on most monitors).
## We want to support up to 1024x768@16 so we need 2MiB video memory.
option CONFIG_SPLASH_GRAPHIC = 1
option CONFIG_VIDEO_MB = 2
-option DEFAULT_CONSOLE_LOGLEVEL = 6
-option MAXIMUM_CONSOLE_LOGLEVEL = 6
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 6
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 6
romimage "normal"
- option USE_FALLBACK_IMAGE = 0
- option ROM_IMAGE_SIZE = 64 * 1024
+ option CONFIG_USE_FALLBACK_IMAGE = 0
+ option CONFIG_ROM_IMAGE_SIZE = 64 * 1024
option COREBOOT_EXTRA_VERSION = ".0Normal"
payload /tmp/filo.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE = 1
- option ROM_IMAGE_SIZE = 64 * 1024
+ option CONFIG_USE_FALLBACK_IMAGE = 1
+ option CONFIG_ROM_IMAGE_SIZE = 64 * 1024
option COREBOOT_EXTRA_VERSION = ".0Fallback"
payload /tmp/filo.elf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
mainboard VENDOR/MAINBOARD
option CC="CROSSCC"
-option CROSS_COMPILE="CROSS_PREFIX"
-option HOSTCC="CROSS_HOSTCC"
+option CONFIG_CROSS_COMPILE="CROSS_PREFIX"
+option CONFIG_HOSTCC="CROSS_HOSTCC"
__COMPRESSION__
__LOGLEVEL__
romimage "fallback"
- option USE_FALLBACK_IMAGE = 1
+ option CONFIG_USE_FALLBACK_IMAGE = 1
payload __PAYLOAD__
end
-buildrom ./coreboot.rom ROM_SIZE "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback"
## Total number of bytes allocated for coreboot use
## (fallback images and payloads).
##
-# option ROM_SIZE = 1024 * 1024
+# option CONFIG_ROM_SIZE = 1024 * 1024
## For VGA BIOS (-64k)
-option ROM_SIZE = (1024 * 1024) - (64 * 1024)
+option CONFIG_ROM_SIZE = (1024 * 1024) - (64 * 1024)
##
## VGA Console
##
## Request this level of debugging output
##
-option DEFAULT_CONSOLE_LOGLEVEL = 7
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 7
romimage "fallback"
- option USE_FALLBACK_IMAGE = 1
- option FALLBACK_SIZE = ROM_SIZE
+ option CONFIG_USE_FALLBACK_IMAGE = 1
+ option CONFIG_FALLBACK_SIZE = CONFIG_ROM_SIZE
option COREBOOT_EXTRA_VERSION = "_IP1000"
payload /tmp/filo.elf
# payload /tmp/eb-5.4.3-eepro100.elf
end
-buildrom ./coreboot.rom ROM_SIZE "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback"
option CONFIG_COMPRESS=0
## Turn off POST codes
-option NO_POST=1
+option CONFIG_NO_POST=1
## Enable serial console
-option DEFAULT_CONSOLE_LOGLEVEL=8
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
option CONFIG_CONSOLE_SERIAL8250=1
## Boot linux from IDE
option CONFIG_IDE_PAYLOAD=1
-option IDE_BOOT_DRIVE=0
-option IDE_SWAB=1
-option IDE_OFFSET=0
+option CONFIG_IDE_BOOT_DRIVE=0
+option CONFIG_IDE_SWAB=1
+option CONFIG_IDE_OFFSET=0
# ROM is 1Mb
-option ROM_SIZE=1024*1024
+option CONFIG_ROM_SIZE=1024*1024
# Set stack and heap sizes (stage 2)
-option STACK_SIZE=0x10000
-option HEAP_SIZE=0x10000
+option CONFIG_STACK_SIZE=0x10000
+option CONFIG_HEAP_SIZE=0x10000
# Sandpoint Demo Board
romimage "normal"
## Base of ROM
- option _ROMBASE=0xfff00000
+ option CONFIG_ROMBASE=0xfff00000
## Sandpoint reset vector
- option _RESET=_ROMBASE+0x100
+ option CONFIG_RESET=CONFIG_ROMBASE+0x100
## Exception vectors (other than reset vector)
- option _EXCEPTION_VECTORS=_RESET+0x100
+ option CONFIG_EXCEPTION_VECTORS=CONFIG_RESET+0x100
## Start of coreboot in the boot rom
- ## = _RESET + exeception vector table size
- option _ROMSTART=_RESET+0x3100
+ ## = CONFIG_RESET + exeception vector table size
+ option CONFIG_ROMSTART=CONFIG_RESET+0x3100
## Coreboot C code runs at this location in RAM
- option _RAMBASE=0x00100000
- option _RAMSTART=0x00100000
+ option CONFIG_RAMBASE=0x00100000
+ option CONFIG_RAMSTART=0x00100000
option CONFIG_BRIQ_750FX=1
#option CONFIG_BRIQ_7400=1
end
-buildrom ./coreboot.rom ROM_SIZE "normal"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal"
target s1846
mainboard tyan/s1846
-option ROM_SIZE = 256 * 1024
+option CONFIG_ROM_SIZE = 256 * 1024
-option MAINBOARD_VENDOR = "Tyan"
-option MAINBOARD_PART_NUMBER = "S1846"
+option CONFIG_MAINBOARD_VENDOR = "Tyan"
+option CONFIG_MAINBOARD_PART_NUMBER = "S1846"
# TODO: Add/fix PIRQ table.
-option HAVE_PIRQ_TABLE = 0
-option IRQ_SLOT_COUNT = 0 # FIXME
+option CONFIG_HAVE_PIRQ_TABLE = 0
+option CONFIG_IRQ_SLOT_COUNT = 0 # FIXME
-option DEFAULT_CONSOLE_LOGLEVEL = 9
-option MAXIMUM_CONSOLE_LOGLEVEL = 9
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
option CONFIG_CONSOLE_VGA = 1
option CONFIG_PCI_ROM_RUN = 1
romimage "normal"
- option USE_FALLBACK_IMAGE = 0
+ option CONFIG_USE_FALLBACK_IMAGE = 0
option COREBOOT_EXTRA_VERSION = ".0Normal"
payload /tmp/filo.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE = 1
+ option CONFIG_USE_FALLBACK_IMAGE = 1
option COREBOOT_EXTRA_VERSION = ".0Fallback"
payload /tmp/filo.elf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
# Tyan s2735
romimage "normal"
# 48K for SCSI FW
-# option ROM_SIZE = 512*1024-48*1024
+# option CONFIG_ROM_SIZE = 512*1024-48*1024
# 48K for SCSI FW and 48K for ATI ROM
-# option ROM_SIZE = 512*1024-48*1024-48*1024
+# option CONFIG_ROM_SIZE = 512*1024-48*1024-48*1024
# 64K for Etherboot
-# option ROM_SIZE = 512*1024-64*1024
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=0x11800
- option XIP_ROM_SIZE=0x20000
+# option CONFIG_ROM_SIZE = 512*1024-64*1024
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=0x11800
+ option CONFIG_XIP_ROM_SIZE=0x20000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Normal"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x11800
- option XIP_ROM_SIZE=0x20000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x11800
+ option CONFIG_XIP_ROM_SIZE=0x20000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
payload ../../../payloads/tg3--eepro100--e1000--filo_hda2.zelf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
# Tyan s2850
romimage "normal"
# 48K for SCSI FW or ATI ROM
- option ROM_SIZE = 512*1024-48*1024
+ option CONFIG_ROM_SIZE = 512*1024-48*1024
# 48K for SCSI FW and 48K for ATI ROM
-# option ROM_SIZE = 512*1024-48*1024-48*1024
+# option CONFIG_ROM_SIZE = 512*1024-48*1024-48*1024
# 64K for Etherboot
-# option ROM_SIZE = 512*1024-64*1024
- option USE_FALLBACK_IMAGE=0
-# option ROM_IMAGE_SIZE=0x11800
-# option ROM_IMAGE_SIZE=0x16000
-# option ROM_IMAGE_SIZE=0x17800
-# option ROM_IMAGE_SIZE=0x13c00
- option ROM_IMAGE_SIZE=0x20000
- option XIP_ROM_SIZE=0x20000
+# option CONFIG_ROM_SIZE = 512*1024-64*1024
+ option CONFIG_USE_FALLBACK_IMAGE=0
+# option CONFIG_ROM_IMAGE_SIZE=0x11800
+# option CONFIG_ROM_IMAGE_SIZE=0x16000
+# option CONFIG_ROM_IMAGE_SIZE=0x17800
+# option CONFIG_ROM_IMAGE_SIZE=0x13c00
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+ option CONFIG_XIP_ROM_SIZE=0x20000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Normal"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
-# option ROM_IMAGE_SIZE=0x11800
-# option ROM_IMAGE_SIZE=0x16000
-# option ROM_IMAGE_SIZE=0x17800
-# option ROM_IMAGE_SIZE=0x13c00
- option ROM_IMAGE_SIZE=0x20000
- option XIP_ROM_SIZE=0x20000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+# option CONFIG_ROM_IMAGE_SIZE=0x11800
+# option CONFIG_ROM_IMAGE_SIZE=0x16000
+# option CONFIG_ROM_IMAGE_SIZE=0x17800
+# option CONFIG_ROM_IMAGE_SIZE=0x13c00
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+ option CONFIG_XIP_ROM_SIZE=0x20000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
# payload ../../../payloads/tg3--eepro100--e1000--filo_hda2.zelf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
# Tyan s2875
romimage "normal"
# 48K for SCSI FW or ATI ROM
- option ROM_SIZE = 512*1024-48*1024
+ option CONFIG_ROM_SIZE = 512*1024-48*1024
# 48K for SCSI FW and 48K for ATI ROM
-# option ROM_SIZE = 512*1024-48*1024-48*1024
+# option CONFIG_ROM_SIZE = 512*1024-48*1024-48*1024
# 64K for Etherboot
-# option ROM_SIZE = 512*1024-64*1024
- option USE_FALLBACK_IMAGE=0
-# option ROM_IMAGE_SIZE=0x11800
-# option ROM_IMAGE_SIZE=0x13800
-# option ROM_IMAGE_SIZE=0x16000
-# option ROM_IMAGE_SIZE=0x17800
- option ROM_IMAGE_SIZE=0x20000
- option XIP_ROM_SIZE=0x20000
+# option CONFIG_ROM_SIZE = 512*1024-64*1024
+ option CONFIG_USE_FALLBACK_IMAGE=0
+# option CONFIG_ROM_IMAGE_SIZE=0x11800
+# option CONFIG_ROM_IMAGE_SIZE=0x13800
+# option CONFIG_ROM_IMAGE_SIZE=0x16000
+# option CONFIG_ROM_IMAGE_SIZE=0x17800
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+ option CONFIG_XIP_ROM_SIZE=0x20000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Normal"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
-# option ROM_IMAGE_SIZE=0x11800
-# option ROM_IMAGE_SIZE=0x13800
-# option ROM_IMAGE_SIZE=0x16000
-# option ROM_IMAGE_SIZE=0x17800
- option ROM_IMAGE_SIZE=0x20000
- option XIP_ROM_SIZE=0x20000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+# option CONFIG_ROM_IMAGE_SIZE=0x11800
+# option CONFIG_ROM_IMAGE_SIZE=0x13800
+# option CONFIG_ROM_IMAGE_SIZE=0x16000
+# option CONFIG_ROM_IMAGE_SIZE=0x17800
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+ option CONFIG_XIP_ROM_SIZE=0x20000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
# payload ../../../payloads/tg3--eepro100--e1000--filo_hda2.zelf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
# Tyan s2880
romimage "normal"
# 48K for SCSI FW or ATI ROM
- option ROM_SIZE = 512*1024-48*1024
+ option CONFIG_ROM_SIZE = 512*1024-48*1024
# 48K for SCSI FW and 48K for ATI ROM
-# option ROM_SIZE = 512*1024-48*1024-48*1024
+# option CONFIG_ROM_SIZE = 512*1024-48*1024-48*1024
# 64K for Etherboot
-# option ROM_SIZE = 512*1024-64*1024
- option USE_FALLBACK_IMAGE=0
-# option ROM_IMAGE_SIZE=0x11800
-# option ROM_IMAGE_SIZE=0x13800
-# option ROM_IMAGE_SIZE=0x16000
- option ROM_IMAGE_SIZE=0x20000
-# option ROM_IMAGE_SIZE=0x17800
- option XIP_ROM_SIZE=0x20000
+# option CONFIG_ROM_SIZE = 512*1024-64*1024
+ option CONFIG_USE_FALLBACK_IMAGE=0
+# option CONFIG_ROM_IMAGE_SIZE=0x11800
+# option CONFIG_ROM_IMAGE_SIZE=0x13800
+# option CONFIG_ROM_IMAGE_SIZE=0x16000
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+# option CONFIG_ROM_IMAGE_SIZE=0x17800
+ option CONFIG_XIP_ROM_SIZE=0x20000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Normal"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
-# option ROM_IMAGE_SIZE=0x11800
-# option ROM_IMAGE_SIZE=0x13800
-# option ROM_IMAGE_SIZE=0x16000
- option ROM_IMAGE_SIZE=0x20000
-# option ROM_IMAGE_SIZE=0x17800
- option XIP_ROM_SIZE=0x20000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+# option CONFIG_ROM_IMAGE_SIZE=0x11800
+# option CONFIG_ROM_IMAGE_SIZE=0x13800
+# option CONFIG_ROM_IMAGE_SIZE=0x16000
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+# option CONFIG_ROM_IMAGE_SIZE=0x17800
+ option CONFIG_XIP_ROM_SIZE=0x20000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
# payload ../../../payloads/tg3--eepro100--e1000--filo_hda2.zelf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
target s2881
mainboard tyan/s2881
-option ROM_SIZE=0x100000
+option CONFIG_ROM_SIZE=0x100000
# 36K for ATI ROM in 1M
-option FALLBACK_SIZE=(ROM_SIZE-0x9000)
+option CONFIG_FALLBACK_SIZE=(CONFIG_ROM_SIZE-0x9000)
# Tyan s2881
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=1
option CONFIG_COMPRESSED_PAYLOAD_LZMA=1
option CONFIG_PRECOMPRESSED_PAYLOAD=1
- option ROM_IMAGE_SIZE=0x17000
- option XIP_ROM_SIZE=0x40000
+ option CONFIG_ROM_IMAGE_SIZE=0x17000
+ option CONFIG_XIP_ROM_SIZE=0x40000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
payload ../payload.elf.lzma
end
-buildrom ./coreboot.rom ROM_SIZE "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback"
# Tyan s2881
romimage "normal"
# 36K for ATI ROM
- option ROM_SIZE = 512*1024-36*1024
+ option CONFIG_ROM_SIZE = 512*1024-36*1024
# 48K for SCSI FW
-# option ROM_SIZE = 512*1024-48*1024
+# option CONFIG_ROM_SIZE = 512*1024-48*1024
# 48K for SCSI FW and 36K for ATI ROM
-# option ROM_SIZE = 512*1024-48*1024-36*1024
+# option CONFIG_ROM_SIZE = 512*1024-48*1024-36*1024
# 64K for Etherboot
-# option ROM_SIZE = 512*1024-64*1024
- option USE_FALLBACK_IMAGE=0
-# option ROM_IMAGE_SIZE=0x11800
-# option ROM_IMAGE_SIZE=0x13000
-# option ROM_IMAGE_SIZE=0x16000
- option ROM_IMAGE_SIZE=0x20000
- option XIP_ROM_SIZE=0x20000
+# option CONFIG_ROM_SIZE = 512*1024-64*1024
+ option CONFIG_USE_FALLBACK_IMAGE=0
+# option CONFIG_ROM_IMAGE_SIZE=0x11800
+# option CONFIG_ROM_IMAGE_SIZE=0x13000
+# option CONFIG_ROM_IMAGE_SIZE=0x16000
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+ option CONFIG_XIP_ROM_SIZE=0x20000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Normal"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
-# option ROM_IMAGE_SIZE=0x11800
-# option ROM_IMAGE_SIZE=0x13000
-# option ROM_IMAGE_SIZE=0x16000
- option ROM_IMAGE_SIZE=0x20000
- option XIP_ROM_SIZE=0x20000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+# option CONFIG_ROM_IMAGE_SIZE=0x11800
+# option CONFIG_ROM_IMAGE_SIZE=0x13000
+# option CONFIG_ROM_IMAGE_SIZE=0x16000
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+ option CONFIG_XIP_ROM_SIZE=0x20000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
payload ../payload.elf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
target s2882
mainboard tyan/s2882
-option ROM_SIZE=0x100000
+option CONFIG_ROM_SIZE=0x100000
# 36K for ATI ROM in 1M
-option FALLBACK_SIZE=(ROM_SIZE-0x9000)
+option CONFIG_FALLBACK_SIZE=(CONFIG_ROM_SIZE-0x9000)
# Tyan s2882
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=1
option CONFIG_COMPRESSED_PAYLOAD_LZMA=1
option CONFIG_PRECOMPRESSED_PAYLOAD=1
- option ROM_IMAGE_SIZE=0x17000
- option XIP_ROM_SIZE=0x40000
+ option CONFIG_ROM_IMAGE_SIZE=0x17000
+ option CONFIG_XIP_ROM_SIZE=0x40000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
payload ../payload.elf.lzma
end
-buildrom ./coreboot.rom ROM_SIZE "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback"
# Tyan s2882
romimage "normal"
# 36K for ATI ROM
- option ROM_SIZE = 512*1024-36*1024
+ option CONFIG_ROM_SIZE = 512*1024-36*1024
# 48K for SCSI FW and 36K for ATI ROM
-# option ROM_SIZE = 512*1024-48*1024-36*1024
+# option CONFIG_ROM_SIZE = 512*1024-48*1024-36*1024
# 64K for Etherboot
-# option ROM_SIZE = 512*1024-64*1024
- option USE_FALLBACK_IMAGE=0
-# option ROM_IMAGE_SIZE=0x11800
-# option ROM_IMAGE_SIZE=0x16000
- option ROM_IMAGE_SIZE=0x20000
- option XIP_ROM_SIZE=0x20000
+# option CONFIG_ROM_SIZE = 512*1024-64*1024
+ option CONFIG_USE_FALLBACK_IMAGE=0
+# option CONFIG_ROM_IMAGE_SIZE=0x11800
+# option CONFIG_ROM_IMAGE_SIZE=0x16000
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+ option CONFIG_XIP_ROM_SIZE=0x20000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Normal"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
-# option ROM_IMAGE_SIZE=0x11800
-# option ROM_IMAGE_SIZE=0x16000
- option ROM_IMAGE_SIZE=0x20000
- option XIP_ROM_SIZE=0x20000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+# option CONFIG_ROM_IMAGE_SIZE=0x11800
+# option CONFIG_ROM_IMAGE_SIZE=0x16000
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+ option CONFIG_XIP_ROM_SIZE=0x20000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
payload ../payload.elf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
# Tyan s2895
romimage "normal"
# 48K for SCSI FW
-# option ROM_SIZE = 512*1024-48*1024
+# option CONFIG_ROM_SIZE = 512*1024-48*1024
# 48K for SCSI FW and 48K for ATI ROM
-# option ROM_SIZE = 512*1024-48*1024-48*1024
+# option CONFIG_ROM_SIZE = 512*1024-48*1024-48*1024
# 64K for Etherboot
-# option ROM_SIZE = 512*1024-64*1024
- option USE_FALLBACK_IMAGE=0
-# option ROM_IMAGE_SIZE=0x13800
-# option ROM_IMAGE_SIZE=0x17800
-# option ROM_IMAGE_SIZE=0x16200
- option ROM_IMAGE_SIZE=0x20000
- option XIP_ROM_SIZE=0x20000
+# option CONFIG_ROM_SIZE = 512*1024-64*1024
+ option CONFIG_USE_FALLBACK_IMAGE=0
+# option CONFIG_ROM_IMAGE_SIZE=0x13800
+# option CONFIG_ROM_IMAGE_SIZE=0x17800
+# option CONFIG_ROM_IMAGE_SIZE=0x16200
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+ option CONFIG_XIP_ROM_SIZE=0x20000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Normal"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
-# option ROM_IMAGE_SIZE=0x13800
-# option ROM_IMAGE_SIZE=0x17800
-# option ROM_IMAGE_SIZE=0x16200
- option ROM_IMAGE_SIZE=0x20000
- option XIP_ROM_SIZE=0x20000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+# option CONFIG_ROM_IMAGE_SIZE=0x13800
+# option CONFIG_ROM_IMAGE_SIZE=0x17800
+# option CONFIG_ROM_IMAGE_SIZE=0x16200
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+ option CONFIG_XIP_ROM_SIZE=0x20000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
# payload ../../../payloads/tg3--eepro100--e1000--filo_hda2_com2.zelf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
mainboard VENDOR/MAINBOARD
option CC="CROSSCC"
-option CROSS_COMPILE="CROSS_PREFIX"
-option HOSTCC="CROSS_HOSTCC"
+option CONFIG_CROSS_COMPILE="CROSS_PREFIX"
+option CONFIG_HOSTCC="CROSS_HOSTCC"
__COMPRESSION__
__LOGLEVEL__
romimage "normal"
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=0x20000
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
option COREBOOT_EXTRA_VERSION=".0-normal"
payload __PAYLOAD__
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x20000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
option COREBOOT_EXTRA_VERSION=".0-fallback"
payload __PAYLOAD__
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
target s2891
mainboard tyan/s2891
-option ROM_SIZE=0x100000
+option CONFIG_ROM_SIZE=0x100000
# 36K for ATI ROM in 1M
-option FALLBACK_SIZE=(ROM_SIZE-0x9000)
+option CONFIG_FALLBACK_SIZE=(CONFIG_ROM_SIZE-0x9000)
# Tyan s2891
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=1
option CONFIG_COMPRESSED_PAYLOAD_LZMA=1
option CONFIG_PRECOMPRESSED_PAYLOAD=1
- option ROM_IMAGE_SIZE=0x17000
- option XIP_ROM_SIZE=0x40000
+ option CONFIG_ROM_IMAGE_SIZE=0x17000
+ option CONFIG_XIP_ROM_SIZE=0x40000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
payload ../payload.elf.lzma
end
-buildrom ./coreboot.rom ROM_SIZE "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback"
# Tyan s2891
romimage "normal"
# 36K for ATI ROM in 1M
- option ROM_SIZE = 1024*1024-36*1024
+ option CONFIG_ROM_SIZE = 1024*1024-36*1024
# 48K for SCSI FW
-# option ROM_SIZE = 512*1024-48*1024
+# option CONFIG_ROM_SIZE = 512*1024-48*1024
# 48K for SCSI FW and 36K for ATI ROM
-# option ROM_SIZE = 512*1024-48*1024-36*1024
+# option CONFIG_ROM_SIZE = 512*1024-48*1024-36*1024
# 64K for Etherboot
-# option ROM_SIZE = 512*1024-64*1024
- option USE_FALLBACK_IMAGE=0
-# option ROM_IMAGE_SIZE=0x11800
-# option ROM_IMAGE_SIZE=0x13000
-# option ROM_IMAGE_SIZE=0x16000
- option ROM_IMAGE_SIZE=0x20000
- option XIP_ROM_SIZE=0x20000
+# option CONFIG_ROM_SIZE = 512*1024-64*1024
+ option CONFIG_USE_FALLBACK_IMAGE=0
+# option CONFIG_ROM_IMAGE_SIZE=0x11800
+# option CONFIG_ROM_IMAGE_SIZE=0x13000
+# option CONFIG_ROM_IMAGE_SIZE=0x16000
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+ option CONFIG_XIP_ROM_SIZE=0x20000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Normal"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
-# option ROM_IMAGE_SIZE=0x11800
-# option ROM_IMAGE_SIZE=0x13000
-# option ROM_IMAGE_SIZE=0x16000
- option ROM_IMAGE_SIZE=0x20000
- option XIP_ROM_SIZE=0x20000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+# option CONFIG_ROM_IMAGE_SIZE=0x11800
+# option CONFIG_ROM_IMAGE_SIZE=0x13000
+# option CONFIG_ROM_IMAGE_SIZE=0x16000
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+ option CONFIG_XIP_ROM_SIZE=0x20000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
payload ../payload.elf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
# Tyan s2891
romimage "normal"
# 48K for SCSI FW or ATI ROM
- option ROM_SIZE = 512*1024-48*1024
+ option CONFIG_ROM_SIZE = 512*1024-48*1024
# 48K for SCSI FW and 48K for ATI ROM
-# option ROM_SIZE = 512*1024-48*1024-48*1024
+# option CONFIG_ROM_SIZE = 512*1024-48*1024-48*1024
# 64K for Etherboot
-# option ROM_SIZE = 512*1024-64*1024
- option USE_FALLBACK_IMAGE=0
-# option ROM_IMAGE_SIZE=0x11800
-# option ROM_IMAGE_SIZE=0x13000
- option ROM_IMAGE_SIZE=0x15800
- option XIP_ROM_SIZE=0x20000
+# option CONFIG_ROM_SIZE = 512*1024-64*1024
+ option CONFIG_USE_FALLBACK_IMAGE=0
+# option CONFIG_ROM_IMAGE_SIZE=0x11800
+# option CONFIG_ROM_IMAGE_SIZE=0x13000
+ option CONFIG_ROM_IMAGE_SIZE=0x15800
+ option CONFIG_XIP_ROM_SIZE=0x20000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Normal"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
-# option ROM_IMAGE_SIZE=0x11800
-# option ROM_IMAGE_SIZE=0x13000
- option ROM_IMAGE_SIZE=0x15800
- option XIP_ROM_SIZE=0x20000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+# option CONFIG_ROM_IMAGE_SIZE=0x11800
+# option CONFIG_ROM_IMAGE_SIZE=0x13000
+ option CONFIG_ROM_IMAGE_SIZE=0x15800
+ option CONFIG_XIP_ROM_SIZE=0x20000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
# payload ../../../payloads/tg3--eepro100--e1000--filo_hda2.zelf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
mainboard VENDOR/MAINBOARD
option CC="CROSSCC"
-option CROSS_COMPILE="CROSS_PREFIX"
-option HOSTCC="CROSS_HOSTCC"
+option CONFIG_CROSS_COMPILE="CROSS_PREFIX"
+option CONFIG_HOSTCC="CROSS_HOSTCC"
__COMPRESSION__
__LOGLEVEL__
romimage "normal"
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=0x20000
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
option COREBOOT_EXTRA_VERSION=".0-normal"
payload __PAYLOAD__
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x20000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
option COREBOOT_EXTRA_VERSION=".0-fallback"
payload __PAYLOAD__
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
mainboard tyan/s2892
# Leave Space for VGA BIOS
-option ROM_SIZE = 1024*1024-36*1024
-#option ROM_SIZE = 1024*1024
+option CONFIG_ROM_SIZE = 1024*1024-36*1024
+#option CONFIG_ROM_SIZE = 1024*1024
option CONFIG_CONSOLE_SERIAL8250 = 1
option CONFIG_CONSOLE_VGA = 1
-option XIP_ROM_SIZE = 0x20000
-option ROM_IMAGE_SIZE = 0x18000
-option FALLBACK_SIZE = ROM_SIZE
+option CONFIG_XIP_ROM_SIZE = 0x20000
+option CONFIG_ROM_IMAGE_SIZE = 0x18000
+option CONFIG_FALLBACK_SIZE = CONFIG_ROM_SIZE
# Tyan s2892
romimage "fallback"
option CONFIG_COMPRESSED_PAYLOAD_LZMA=1
option CONFIG_PRECOMPRESSED_PAYLOAD=1
- option USE_FALLBACK_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=1
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
payload ../payload.elf.lzma
end
-buildrom ./coreboot.rom ROM_SIZE "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback"
# Tyan s2892
romimage "normal"
# 36K for ATI ROM in 1M
- option ROM_SIZE = 1024*1024-36*1024
+ option CONFIG_ROM_SIZE = 1024*1024-36*1024
# 48K for SCSI FW or ATI ROM
-# option ROM_SIZE = 512*1024-48*1024
+# option CONFIG_ROM_SIZE = 512*1024-48*1024
# 48K for SCSI FW and 48K for ATI ROM
-# option ROM_SIZE = 512*1024-48*1024-48*1024
+# option CONFIG_ROM_SIZE = 512*1024-48*1024-48*1024
# 64K for Etherboot
-# option ROM_SIZE = 512*1024-64*1024
- option USE_FALLBACK_IMAGE=0
-# option ROM_IMAGE_SIZE=0x11800
-# option ROM_IMAGE_SIZE=0x13800
-# option ROM_IMAGE_SIZE=0x16380
- option ROM_IMAGE_SIZE=0x20000
-# option ROM_IMAGE_SIZE=0x17800
- option XIP_ROM_SIZE=0x20000
+# option CONFIG_ROM_SIZE = 512*1024-64*1024
+ option CONFIG_USE_FALLBACK_IMAGE=0
+# option CONFIG_ROM_IMAGE_SIZE=0x11800
+# option CONFIG_ROM_IMAGE_SIZE=0x13800
+# option CONFIG_ROM_IMAGE_SIZE=0x16380
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+# option CONFIG_ROM_IMAGE_SIZE=0x17800
+ option CONFIG_XIP_ROM_SIZE=0x20000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Normal"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
-# option ROM_IMAGE_SIZE=0x11800
-# option ROM_IMAGE_SIZE=0x13800
-# option ROM_IMAGE_SIZE=0x16380
- option ROM_IMAGE_SIZE=0x20000
-# option ROM_IMAGE_SIZE=0x17800
- option XIP_ROM_SIZE=0x20000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+# option CONFIG_ROM_IMAGE_SIZE=0x11800
+# option CONFIG_ROM_IMAGE_SIZE=0x13800
+# option CONFIG_ROM_IMAGE_SIZE=0x16380
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+# option CONFIG_ROM_IMAGE_SIZE=0x17800
+ option CONFIG_XIP_ROM_SIZE=0x20000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
payload ../payload.elf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
mainboard VENDOR/MAINBOARD
option CC="CROSSCC"
-option CROSS_COMPILE="CROSS_PREFIX"
-option HOSTCC="CROSS_HOSTCC"
+option CONFIG_CROSS_COMPILE="CROSS_PREFIX"
+option CONFIG_HOSTCC="CROSS_HOSTCC"
__COMPRESSION__
__LOGLEVEL__
romimage "normal"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=0x20000
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
option COREBOOT_EXTRA_VERSION=".0-normal"
payload __PAYLOAD__
end
romimage "fallback"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x20000
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
option COREBOOT_EXTRA_VERSION=".0-fallback"
payload __PAYLOAD__
end
romimage "failover"
- option USE_FAILOVER_IMAGE=1
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=FAILOVER_SIZE
- option XIP_ROM_SIZE=FAILOVER_SIZE
+ option CONFIG_USE_FAILOVER_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=CONFIG_FAILOVER_SIZE
+ option CONFIG_XIP_ROM_SIZE=CONFIG_FAILOVER_SIZE
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback" "failover"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback" "failover"
option CONFIG_CONSOLE_SERIAL8250 = 1
option CONFIG_CONSOLE_VGA = 1
-option XIP_ROM_SIZE = 0x20000
-option ROM_IMAGE_SIZE = 0x18000
-option HAVE_FAILOVER_BOOT = 0
-option FAILOVER_SIZE = 0
-option FALLBACK_SIZE = ROM_SIZE
+option CONFIG_XIP_ROM_SIZE = 0x20000
+option CONFIG_ROM_IMAGE_SIZE = 0x18000
+option CONFIG_HAVE_FAILOVER_BOOT = 0
+option CONFIG_FAILOVER_SIZE = 0
+option CONFIG_FALLBACK_SIZE = CONFIG_ROM_SIZE
option CONFIG_COMPRESSED_PAYLOAD_LZMA = 1
option CONFIG_PRECOMPRESSED_PAYLOAD = 1
# Tyan s2895
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=1
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
payload ../payload.elf.lzma
end
-buildrom ./coreboot.rom ROM_SIZE "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback"
# Tyan s2895
romimage "normal"
# 48K for SCSI FW
-# option ROM_SIZE = 475136
+# option CONFIG_ROM_SIZE = 475136
# 48K for SCSI FW and 48K for ATI ROM
-# option ROM_SIZE = 425984
+# option CONFIG_ROM_SIZE = 425984
# 64K for Etherboot
-# option ROM_SIZE = 458752
+# option CONFIG_ROM_SIZE = 458752
# 64K for NIC option 48K for Raid option rom
-# option ROM_SIZE = 409600
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=0
-# option ROM_IMAGE_SIZE=0x11800
-# option ROM_IMAGE_SIZE=0x13800
-# option ROM_IMAGE_SIZE=0x15000
- option ROM_IMAGE_SIZE=0x20000
-# option ROM_IMAGE_SIZE=0x17800
- option XIP_ROM_SIZE=0x20000
+# option CONFIG_ROM_SIZE = 409600
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=0
+# option CONFIG_ROM_IMAGE_SIZE=0x11800
+# option CONFIG_ROM_IMAGE_SIZE=0x13800
+# option CONFIG_ROM_IMAGE_SIZE=0x15000
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+# option CONFIG_ROM_IMAGE_SIZE=0x17800
+ option CONFIG_XIP_ROM_SIZE=0x20000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Normal"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
end
romimage "fallback"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=1
-# option ROM_IMAGE_SIZE=0x11800
-# option ROM_IMAGE_SIZE=0x13800
-# option ROM_IMAGE_SIZE=0x15000
- option ROM_IMAGE_SIZE=0x20000
-# option ROM_IMAGE_SIZE=0x17800
- option XIP_ROM_SIZE=0x20000
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=1
+# option CONFIG_ROM_IMAGE_SIZE=0x11800
+# option CONFIG_ROM_IMAGE_SIZE=0x13800
+# option CONFIG_ROM_IMAGE_SIZE=0x15000
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+# option CONFIG_ROM_IMAGE_SIZE=0x17800
+ option CONFIG_XIP_ROM_SIZE=0x20000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
end
romimage "failover"
- option USE_FAILOVER_IMAGE=1
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=FAILOVER_SIZE
- option XIP_ROM_SIZE=FAILOVER_SIZE
+ option CONFIG_USE_FAILOVER_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=CONFIG_FAILOVER_SIZE
+ option CONFIG_XIP_ROM_SIZE=CONFIG_FAILOVER_SIZE
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Failover"
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback" "failover"
-#buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback" "failover"
+#buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
mainboard VENDOR/MAINBOARD
option CC="CROSSCC"
-option CROSS_COMPILE="CROSS_PREFIX"
-option HOSTCC="CROSS_HOSTCC"
+option CONFIG_CROSS_COMPILE="CROSS_PREFIX"
+option CONFIG_HOSTCC="CROSS_HOSTCC"
__COMPRESSION__
__LOGLEVEL__
romimage "normal"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=0x20000
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
option COREBOOT_EXTRA_VERSION=".0-normal"
payload __PAYLOAD__
end
romimage "fallback"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x20000
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
option COREBOOT_EXTRA_VERSION=".0-fallback"
payload __PAYLOAD__
end
romimage "failover"
- option USE_FAILOVER_IMAGE=1
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=FAILOVER_SIZE
- option XIP_ROM_SIZE=FAILOVER_SIZE
+ option CONFIG_USE_FAILOVER_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=CONFIG_FAILOVER_SIZE
+ option CONFIG_XIP_ROM_SIZE=CONFIG_FAILOVER_SIZE
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback" "failover"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback" "failover"
# serengeti_leopard
romimage "normal"
# 48K for SCSI FW
-# option ROM_SIZE = 475136
+# option CONFIG_ROM_SIZE = 475136
# 48K for SCSI FW and 48K for ATI ROM
-# option ROM_SIZE = 425984
+# option CONFIG_ROM_SIZE = 425984
# 64K for Etherboot
-# option ROM_SIZE = 458752
+# option CONFIG_ROM_SIZE = 458752
# 44k for atixx.rom
-# option ROM_SIZE = 479232
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=0
-# option ROM_IMAGE_SIZE=0x13800
-# option ROM_IMAGE_SIZE=0x18800
- option ROM_IMAGE_SIZE=0x20000
-# option ROM_IMAGE_SIZE=0x15800
- option XIP_ROM_SIZE=0x40000
+# option CONFIG_ROM_SIZE = 479232
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=0
+# option CONFIG_ROM_IMAGE_SIZE=0x13800
+# option CONFIG_ROM_IMAGE_SIZE=0x18800
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+# option CONFIG_ROM_IMAGE_SIZE=0x15800
+ option CONFIG_XIP_ROM_SIZE=0x40000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Normal"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
end
romimage "fallback"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=1
-# option ROM_IMAGE_SIZE=0x13800
-# option ROM_IMAGE_SIZE=0x19800
- option ROM_IMAGE_SIZE=0x20000
-# option ROM_IMAGE_SIZE=0x15800
- option XIP_ROM_SIZE=0x40000
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=1
+# option CONFIG_ROM_IMAGE_SIZE=0x13800
+# option CONFIG_ROM_IMAGE_SIZE=0x19800
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+# option CONFIG_ROM_IMAGE_SIZE=0x15800
+ option CONFIG_XIP_ROM_SIZE=0x40000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
end
romimage "failover"
- option USE_FAILOVER_IMAGE=1
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=FAILOVER_SIZE
- option XIP_ROM_SIZE=FAILOVER_SIZE
+ option CONFIG_USE_FAILOVER_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=CONFIG_FAILOVER_SIZE
+ option CONFIG_XIP_ROM_SIZE=CONFIG_FAILOVER_SIZE
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Failover"
end
-#buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback" "failover"
+#buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback" "failover"
target s2912
mainboard tyan/s2912
-option ROM_SIZE=0x200000
-option FALLBACK_SIZE=(ROM_SIZE-0x1000)
+option CONFIG_ROM_SIZE=0x200000
+option CONFIG_FALLBACK_SIZE=(CONFIG_ROM_SIZE-0x1000)
romimage "fallback"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=1
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=1
option CONFIG_COMPRESSED_PAYLOAD_LZMA=1
option CONFIG_PRECOMPRESSED_PAYLOAD=1
-# option ROM_IMAGE_SIZE=0x19800
- option ROM_IMAGE_SIZE=0x17000
-# option ROM_IMAGE_SIZE=0x15800
-# option ROM_IMAGE_SIZE=0x13800
- option XIP_ROM_SIZE=0x40000
+# option CONFIG_ROM_IMAGE_SIZE=0x19800
+ option CONFIG_ROM_IMAGE_SIZE=0x17000
+# option CONFIG_ROM_IMAGE_SIZE=0x15800
+# option CONFIG_ROM_IMAGE_SIZE=0x13800
+ option CONFIG_XIP_ROM_SIZE=0x40000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
end
romimage "failover"
- option USE_FAILOVER_IMAGE=1
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=FAILOVER_SIZE
- option XIP_ROM_SIZE=FAILOVER_SIZE
+ option CONFIG_USE_FAILOVER_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=CONFIG_FAILOVER_SIZE
+ option CONFIG_XIP_ROM_SIZE=CONFIG_FAILOVER_SIZE
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Failover"
end
-buildrom ./coreboot.rom ROM_SIZE "fallback" "failover"
-#buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback" "failover"
+#buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
mainboard tyan/s2912_fam10
option CC="CROSSCC"
-option CROSS_COMPILE="CROSS_PREFIX"
-option HOSTCC="CROSS_HOSTCC"
+option CONFIG_CROSS_COMPILE="CROSS_PREFIX"
+option CONFIG_HOSTCC="CROSS_HOSTCC"
__COMPRESSION__
__LOGLEVEL__
romimage "normal"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=0x34000
- option XIP_ROM_SIZE=0x40000
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=0x34000
+ option CONFIG_XIP_ROM_SIZE=0x40000
option COREBOOT_EXTRA_VERSION=".0-Normal"
payload __PAYLOAD__
end
romimage "fallback"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x34000
- option XIP_ROM_SIZE=0x40000
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x34000
+ option CONFIG_XIP_ROM_SIZE=0x40000
option COREBOOT_EXTRA_VERSION=".0-Fallback"
payload __PAYLOAD__
end
romimage "failover"
- option USE_FAILOVER_IMAGE=1
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=FAILOVER_SIZE
- option XIP_ROM_SIZE=FAILOVER_SIZE
+ option CONFIG_USE_FAILOVER_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=CONFIG_FAILOVER_SIZE
+ option CONFIG_XIP_ROM_SIZE=CONFIG_FAILOVER_SIZE
option COREBOOT_EXTRA_VERSION=".0-Failover"
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback" "failover"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback" "failover"
mainboard tyan/s2912_fam10
# Make room for ATI ES1000 VGA ROM
-option ROM_SIZE=ROM_SIZE-44*1024
+option CONFIG_ROM_SIZE=ROM_SIZE-44*1024
romimage "normal"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=0x20000
- option XIP_ROM_SIZE=0x40000
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+ option CONFIG_XIP_ROM_SIZE=0x40000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Normal"
# payload ../../../../payloads/forcedeth--filo_hda2_vga_5_4_2_mcp55.zelf
payload ../payload.elf
end
romimage "fallback"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x20000
- option XIP_ROM_SIZE=0x40000
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+ option CONFIG_XIP_ROM_SIZE=0x40000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
# payload ../../../../payloads/forcedeth--filo_hda2_vga_5_4_2_mcp55.zelf
payload ../payload.elf
end
romimage "failover"
- option USE_FAILOVER_IMAGE=1
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=FAILOVER_SIZE
- option XIP_ROM_SIZE=FAILOVER_SIZE
+ option CONFIG_USE_FAILOVER_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=CONFIG_FAILOVER_SIZE
+ option CONFIG_XIP_ROM_SIZE=CONFIG_FAILOVER_SIZE
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Failover"
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback" "failover"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback" "failover"
target s2912
mainboard tyan/s2912
-option ROM_SIZE=0x200000
-option FALLBACK_SIZE=(ROM_SIZE-0x1000)
+option CONFIG_ROM_SIZE=0x200000
+option CONFIG_FALLBACK_SIZE=(CONFIG_ROM_SIZE-0x1000)
romimage "fallback"
- option USE_FAILOVER_IMAGE=0
- option USE_FALLBACK_IMAGE=1
+ option CONFIG_USE_FAILOVER_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=1
option CONFIG_COMPRESSED_PAYLOAD_LZMA=1
option CONFIG_PRECOMPRESSED_PAYLOAD=1
-# option ROM_IMAGE_SIZE=0x19800
- option ROM_IMAGE_SIZE=0x17000
-# option ROM_IMAGE_SIZE=0x15800
-# option ROM_IMAGE_SIZE=0x13800
- option XIP_ROM_SIZE=0x40000
+# option CONFIG_ROM_IMAGE_SIZE=0x19800
+ option CONFIG_ROM_IMAGE_SIZE=0x17000
+# option CONFIG_ROM_IMAGE_SIZE=0x15800
+# option CONFIG_ROM_IMAGE_SIZE=0x13800
+ option CONFIG_XIP_ROM_SIZE=0x40000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
end
romimage "failover"
- option USE_FAILOVER_IMAGE=1
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=FAILOVER_SIZE
- option XIP_ROM_SIZE=FAILOVER_SIZE
+ option CONFIG_USE_FAILOVER_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=CONFIG_FAILOVER_SIZE
+ option CONFIG_XIP_ROM_SIZE=CONFIG_FAILOVER_SIZE
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Failover"
end
-buildrom ./coreboot.rom ROM_SIZE "fallback" "failover"
-#buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback" "failover"
+#buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
# Tyan s4880
romimage "normal"
# 48K for SCSI FW or ATI ROM
- option ROM_SIZE = 512*1024-48*1024
+ option CONFIG_ROM_SIZE = 512*1024-48*1024
# 48K for SCSI FW and 48K for ATI ROM
-# option ROM_SIZE = 512*1024-48*1024-48*1024
+# option CONFIG_ROM_SIZE = 512*1024-48*1024-48*1024
# 64K for Etherboot
-# option ROM_SIZE = 512*1024-64*1024
- option USE_FALLBACK_IMAGE=0
-# option ROM_IMAGE_SIZE=0x19000
-# option ROM_IMAGE_SIZE=0x19c00
- option ROM_IMAGE_SIZE=0x20000
- option XIP_ROM_SIZE=0x20000
+# option CONFIG_ROM_SIZE = 512*1024-64*1024
+ option CONFIG_USE_FALLBACK_IMAGE=0
+# option CONFIG_ROM_IMAGE_SIZE=0x19000
+# option CONFIG_ROM_IMAGE_SIZE=0x19c00
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+ option CONFIG_XIP_ROM_SIZE=0x20000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Normal"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
-# option ROM_IMAGE_SIZE=0x19000
-# option ROM_IMAGE_SIZE=0x19c00
- option ROM_IMAGE_SIZE=0x20000
- option XIP_ROM_SIZE=0x20000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+# option CONFIG_ROM_IMAGE_SIZE=0x19000
+# option CONFIG_ROM_IMAGE_SIZE=0x19c00
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+ option CONFIG_XIP_ROM_SIZE=0x20000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
# payload ../../../payloads/tg3--eepro100--e1000--filo_hda2.zelf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
# Tyan s4882
romimage "normal"
# 48K for SCSI FW or ATI ROM
- option ROM_SIZE = 512*1024-48*1024
+ option CONFIG_ROM_SIZE = 512*1024-48*1024
# 48K for SCSI FW and 48K for ATI ROM
-# option ROM_SIZE = 512*1024-48*1024-48*1024
+# option CONFIG_ROM_SIZE = 512*1024-48*1024-48*1024
# 64K for Etherboot
-# option ROM_SIZE = 512*1024-64*1024
- option USE_FALLBACK_IMAGE=0
-# option ROM_IMAGE_SIZE=0x19000
-# option ROM_IMAGE_SIZE=0x19c00
-# option ROM_IMAGE_SIZE=0x18800
-# option ROM_IMAGE_SIZE=0x16200
- option ROM_IMAGE_SIZE=0x20000
- option XIP_ROM_SIZE=0x20000
+# option CONFIG_ROM_SIZE = 512*1024-64*1024
+ option CONFIG_USE_FALLBACK_IMAGE=0
+# option CONFIG_ROM_IMAGE_SIZE=0x19000
+# option CONFIG_ROM_IMAGE_SIZE=0x19c00
+# option CONFIG_ROM_IMAGE_SIZE=0x18800
+# option CONFIG_ROM_IMAGE_SIZE=0x16200
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+ option CONFIG_XIP_ROM_SIZE=0x20000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Normal"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
-# option ROM_IMAGE_SIZE=0x19000
-# option ROM_IMAGE_SIZE=0x19c00
-# option ROM_IMAGE_SIZE=0x18800
-# option ROM_IMAGE_SIZE=0x16200
- option ROM_IMAGE_SIZE=0x20000
- option XIP_ROM_SIZE=0x20000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+# option CONFIG_ROM_IMAGE_SIZE=0x19000
+# option CONFIG_ROM_IMAGE_SIZE=0x19c00
+# option CONFIG_ROM_IMAGE_SIZE=0x18800
+# option CONFIG_ROM_IMAGE_SIZE=0x16200
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
+ option CONFIG_XIP_ROM_SIZE=0x20000
option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
# payload ../../../payloads/tg3--ide_disk.zelf
# payload ../../../payloads/filo.elf
# payload ../../../payloads/tg3--eepro100--e1000--filo_hda2.zelf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
mainboard VENDOR/MAINBOARD
option CC="CROSSCC"
-option CROSS_COMPILE="CROSS_PREFIX"
-option HOSTCC="CROSS_HOSTCC"
+option CONFIG_CROSS_COMPILE="CROSS_PREFIX"
+option CONFIG_HOSTCC="CROSS_HOSTCC"
__COMPRESSION__
__LOGLEVEL__
-option ROM_SIZE=512*1024
+option CONFIG_ROM_SIZE=512*1024
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x20000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x20000
option COREBOOT_EXTRA_VERSION=".0-fallback"
payload __PAYLOAD__
end
-buildrom ./coreboot.rom ROM_SIZE "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback"
target via_epia_cn
mainboard via/epia-cn
-option MAXIMUM_CONSOLE_LOGLEVEL=8
-option DEFAULT_CONSOLE_LOGLEVEL=8
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
option CONFIG_CONSOLE_SERIAL8250=1
# coreboot C code runs at this location in RAM
-option _RAMBASE=0x00004000
+option CONFIG_RAMBASE=0x00004000
#
# Generate the final ROM like this:
# cat vgabios bochsbios coreboot.rom > coreboot.rom.final
#
-option ROM_SIZE = (512 * 1024) - (64 * 1024) - (64 * 1024)
+option CONFIG_ROM_SIZE = (512 * 1024) - (64 * 1024) - (64 * 1024)
romimage "image"
option COREBOOT_EXTRA_VERSION = "-epiacn"
payload ../payload.elf
end
-buildrom ./coreboot.rom ROM_SIZE "image"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "image"
mainboard VENDOR/MAINBOARD
option CC="CROSSCC"
-option CROSS_COMPILE="CROSS_PREFIX"
-option HOSTCC="CROSS_HOSTCC"
+option CONFIG_CROSS_COMPILE="CROSS_PREFIX"
+option CONFIG_HOSTCC="CROSS_HOSTCC"
__COMPRESSION__
__LOGLEVEL__
-option ROM_SIZE=256*1024
+option CONFIG_ROM_SIZE=256*1024
romimage "normal"
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=64*1024
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=64*1024
option COREBOOT_EXTRA_VERSION=".0-Normal"
payload __PAYLOAD__
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=64*1024
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=64*1024
option COREBOOT_EXTRA_VERSION=".0-Fallback"
payload __PAYLOAD__
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
mainboard via/epia-m
-option MAXIMUM_CONSOLE_LOGLEVEL=8
-option DEFAULT_CONSOLE_LOGLEVEL=8
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
option CONFIG_CONSOLE_SERIAL8250=1
-option ROM_SIZE=512*1024
+option CONFIG_ROM_SIZE=512*1024
-option HAVE_OPTION_TABLE=1
+option CONFIG_HAVE_OPTION_TABLE=1
option CONFIG_ROM_PAYLOAD=1
-option HAVE_FALLBACK_BOOT=1
+option CONFIG_HAVE_FALLBACK_BOOT=1
###
### Compute the location and size of where this firmware image
### (coreboot plus bootloader) will live in the boot rom chip.
###
-option FALLBACK_SIZE=131072
+option CONFIG_FALLBACK_SIZE=131072
## Coreboot C code runs at this location in RAM
-option _RAMBASE=0x00004000
+option CONFIG_RAMBASE=0x00004000
#
###
# Via EPIA M
#
romimage "normal"
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=0x10000
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=0x10000
option COREBOOT_EXTRA_VERSION=".0Normal"
# payload /usr/share/etherboot/5.1.9pre2-lnxi-lb/tg3--ide_disk.zelf
# payload ../../../../tg3--ide_disk.zelf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x10000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x10000
option COREBOOT_EXTRA_VERSION=".0Fallback"
# payload /usr/share/etherboot/5.1.9pre2-lnxi-lb/tg3--ide_disk.zelf
# payload ../../../../tg3--ide_disk.zelf
payload ../../../../../lnxieepro100.ebi
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
mainboard via/epia-m
-option MAXIMUM_CONSOLE_LOGLEVEL=8
-option DEFAULT_CONSOLE_LOGLEVEL=8
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
option CONFIG_CONSOLE_SERIAL8250=1
-option ROM_SIZE=256*1024
+option CONFIG_ROM_SIZE=256*1024
-option HAVE_OPTION_TABLE=1
+option CONFIG_HAVE_OPTION_TABLE=1
option CONFIG_ROM_PAYLOAD=1
-option HAVE_FALLBACK_BOOT=1
+option CONFIG_HAVE_FALLBACK_BOOT=1
###
### Compute the location and size of where this firmware image
### (coreboot plus bootloader) will live in the boot rom chip.
###
-option FALLBACK_SIZE=131072
+option CONFIG_FALLBACK_SIZE=131072
## Coreboot C code runs at this location in RAM
-option _RAMBASE=0x00004000
+option CONFIG_RAMBASE=0x00004000
#
###
# Via EPIA-M
#
romimage "normal"
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=0x10000
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=0x10000
option COREBOOT_EXTRA_VERSION=".0Normal"
# payload /usr/share/etherboot/5.1.9pre2-lnxi-lb/tg3--ide_disk.zelf
# payload ../../../../tg3--ide_disk.zelf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x10000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x10000
option COREBOOT_EXTRA_VERSION=".0Fallback"
# payload /usr/share/etherboot/5.1.9pre2-lnxi-lb/tg3--ide_disk.zelf
# payload ../../../../tg3--ide_disk.zelf
payload ../../../../../lnxieepro100.ebi
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
mainboard via/epia-m
-option MAXIMUM_CONSOLE_LOGLEVEL=8
-option DEFAULT_CONSOLE_LOGLEVEL=8
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
option CONFIG_CONSOLE_SERIAL8250=1
-option ROM_SIZE=256*1024
+option CONFIG_ROM_SIZE=256*1024
-option HAVE_OPTION_TABLE=1
+option CONFIG_HAVE_OPTION_TABLE=1
option CONFIG_ROM_PAYLOAD=1
-option HAVE_FALLBACK_BOOT=1
+option CONFIG_HAVE_FALLBACK_BOOT=1
###
### Compute the location and size of where this firmware image
### (coreboot plus bootloader) will live in the boot rom chip.
###
-option FALLBACK_SIZE=131072
+option CONFIG_FALLBACK_SIZE=131072
## Coreboot C code runs at this location in RAM
-option _RAMBASE=0x00004000
+option CONFIG_RAMBASE=0x00004000
#
###
# EPIA-M
#
romimage "normal"
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=0x10000
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=0x10000
option COREBOOT_EXTRA_VERSION=".0Normal"
# payload /usr/share/etherboot/5.1.9pre2-lnxi-lb/tg3--ide_disk.zelf
# payload ../../../../tg3--ide_disk.zelf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x10000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x10000
option COREBOOT_EXTRA_VERSION=".0Fallback"
# payload /usr/share/etherboot/5.1.9pre2-lnxi-lb/tg3--ide_disk.zelf
# payload ../../../../tg3--ide_disk.zelf
payload ../../../../../../filo.elf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
target via_epia-m
mainboard via/epia-m
-option MAXIMUM_CONSOLE_LOGLEVEL=8
-option DEFAULT_CONSOLE_LOGLEVEL=8
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
option CONFIG_CONSOLE_SERIAL8250=1
-option ROM_SIZE=256*1024
+option CONFIG_ROM_SIZE=256*1024
-option HAVE_OPTION_TABLE=1
+option CONFIG_HAVE_OPTION_TABLE=1
option CONFIG_ROM_PAYLOAD=1
-option HAVE_FALLBACK_BOOT=1
+option CONFIG_HAVE_FALLBACK_BOOT=1
#option CONFIG_COMPRESSED_PAYLOAD_NRV2B=1
option CONFIG_COMPRESSED_PAYLOAD_NRV2B=0
### Compute the location and size of where this firmware image
### (coreboot plus bootloader) will live in the boot rom chip.
###
-option FALLBACK_SIZE=131072
+option CONFIG_FALLBACK_SIZE=131072
## Coreboot C code runs at this location in RAM
-option _RAMBASE=0x00004000
+option CONFIG_RAMBASE=0x00004000
#
# Via EPIA M
#
romimage "normal"
- option USE_FALLBACK_IMAGE=0
-#option ROM_IMAGE_SIZE=128*1024
- option ROM_IMAGE_SIZE=64*1024
+ option CONFIG_USE_FALLBACK_IMAGE=0
+#option CONFIG_ROM_IMAGE_SIZE=128*1024
+ option CONFIG_ROM_IMAGE_SIZE=64*1024
option COREBOOT_EXTRA_VERSION=".0-Normal"
payload $(HOME)/svn/payload.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
- #option ROM_IMAGE_SIZE=128*1024
- option ROM_IMAGE_SIZE=60*1024
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ #option CONFIG_ROM_IMAGE_SIZE=128*1024
+ option CONFIG_ROM_IMAGE_SIZE=60*1024
option COREBOOT_EXTRA_VERSION=".0-Fallback"
payload $(HOME)/svn/payload.elf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
mainboard via/epia-m
-option MAXIMUM_CONSOLE_LOGLEVEL=8
-option DEFAULT_CONSOLE_LOGLEVEL=8
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
option CONFIG_CONSOLE_SERIAL8250=1
-option ROM_SIZE=256*1024
-option HAVE_OPTION_TABLE=1
+option CONFIG_ROM_SIZE=256*1024
+option CONFIG_HAVE_OPTION_TABLE=1
option CONFIG_ROM_PAYLOAD=1
-option HAVE_FALLBACK_BOOT=1
+option CONFIG_HAVE_FALLBACK_BOOT=1
###
### Compute the location and size of where this firmware image
### (coreboot plus bootloader) will live in the boot rom chip.
###
-option FALLBACK_SIZE=0x18000
+option CONFIG_FALLBACK_SIZE=0x18000
## Coreboot C code runs at this location in RAM
-option _RAMBASE=0x00004000
+option CONFIG_RAMBASE=0x00004000
###
### Compute the start location and size size of
# EPIA-M
#
romimage "normal"
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=0xc000
- option ROM_SECTION_OFFSET=0x10000
- option ROM_SECTION_SIZE=0x18000
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=0xc000
+ option CONFIG_ROM_SECTION_OFFSET=0x10000
+ option CONFIG_ROM_SECTION_SIZE=0x18000
option COREBOOT_EXTRA_VERSION=".0-Normal"
payload $(HOME)/svn/filo.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0xc000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0xc000
option COREBOOT_EXTRA_VERSION=".0-Fallback"
payload $(HOME)/svn/filo.elf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
payload ../payload.elf
end
-buildrom ./coreboot.rom ROM_SIZE "image"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "image"
target epia.512kflash
mainboard via/epia
-option ROM_SIZE=512*1024
+option CONFIG_ROM_SIZE=512*1024
#
# Via Epia
romimage "normal"
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=0x10000
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=0x10000
option COREBOOT_EXTRA_VERSION=".0Normal"
# payload /usr/share/etherboot/5.1.9pre2-lnxi-lb/tg3--ide_disk.zelf
# payload ../../../../tg3--ide_disk.zelf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x10000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x10000
option COREBOOT_EXTRA_VERSION=".0Fallback"
# payload /usr/share/etherboot/5.1.9pre2-lnxi-lb/tg3--ide_disk.zelf
# payload ../../../../tg3--ide_disk.zelf
payload ../../../../../lnxieepro100.ebi
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
target epia.512kflash.linuxtiny
mainboard via/epia
-option ROM_SIZE=512*1024
-option FALLBACK_SIZE=ROM_SIZE
-option MAXIMUM_CONSOLE_LOGLEVEL=9
-option DEFAULT_CONSOLE_LOGLEVEL=9
+option CONFIG_ROM_SIZE=512*1024
+option CONFIG_FALLBACK_SIZE=CONFIG_ROM_SIZE
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=9
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL=9
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=64*1024
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=64*1024
option COREBOOT_EXTRA_VERSION=".0Fallback"
# payload /usr/share/etherboot/5.1.9pre2-lnxi-lb/tg3--ide_disk.zelf
# payload ../../../../tg3--ide_disk.zelf
payload /tmp/linux.elf
end
-buildrom ./coreboot.rom ROM_SIZE "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback"
#
# Via Epia
romimage "normal"
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=0x10000
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=0x10000
option COREBOOT_EXTRA_VERSION=".0Normal"
# payload /usr/share/etherboot/5.1.9pre2-lnxi-lb/tg3--ide_disk.zelf
# payload ../../../../tg3--ide_disk.zelf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x10000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x10000
option COREBOOT_EXTRA_VERSION=".0Fallback"
# payload /usr/share/etherboot/5.1.9pre2-lnxi-lb/tg3--ide_disk.zelf
# payload ../../../../tg3--ide_disk.zelf
payload /tmp/filo.elf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
target epia-ituner-filo
mainboard via/epia
-option MAXIMUM_CONSOLE_LOGLEVEL=9
-option DEFAULT_CONSOLE_LOGLEVEL=9
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=9
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL=9
#
# Via Epia
romimage "normal"
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=0x10000
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=0x10000
option COREBOOT_EXTRA_VERSION=".0Normal"
# payload /usr/share/etherboot/5.1.9pre2-lnxi-lb/tg3--ide_disk.zelf
# payload ../../../../tg3--ide_disk.zelf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x10000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x10000
option COREBOOT_EXTRA_VERSION=".0Fallback"
# payload /usr/share/etherboot/5.1.9pre2-lnxi-lb/tg3--ide_disk.zelf
# payload ../../../../tg3--ide_disk.zelf
payload /tmp/filo.elf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
target epia
mainboard via/epia
-option MAXIMUM_CONSOLE_LOGLEVEL=9
-option DEFAULT_CONSOLE_LOGLEVEL=9
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=9
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL=9
#
# Via Epia
romimage "normal"
- option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=0x10000
+ option CONFIG_USE_FALLBACK_IMAGE=0
+ option CONFIG_ROM_IMAGE_SIZE=0x10000
option COREBOOT_EXTRA_VERSION=".0Normal"
# payload /usr/share/etherboot/5.1.9pre2-lnxi-lb/tg3--ide_disk.zelf
# payload ../../../../tg3--ide_disk.zelf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x10000
+ option CONFIG_USE_FALLBACK_IMAGE=1
+ option CONFIG_ROM_IMAGE_SIZE=0x10000
option COREBOOT_EXTRA_VERSION=".0Fallback"
# payload /usr/share/etherboot/5.1.9pre2-lnxi-lb/tg3--ide_disk.zelf
# payload ../../../../tg3--ide_disk.zelf
payload /etc/hosts
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
mainboard VENDOR/MAINBOARD
option CC = "CROSSCC"
-option CROSS_COMPILE = "CROSS_PREFIX"
-option HOSTCC = "CROSS_HOSTCC"
+option CONFIG_CROSS_COMPILE = "CROSS_PREFIX"
+option CONFIG_HOSTCC = "CROSS_HOSTCC"
__COMPRESSION__
__LOGLEVEL__
-option ROM_SIZE = 512 * 1024
+option CONFIG_ROM_SIZE = 512 * 1024
romimage "image"
- option USE_FALLBACK_IMAGE = 1
- option ROM_IMAGE_SIZE = 128 * 1024
+ option CONFIG_USE_FALLBACK_IMAGE = 1
+ option CONFIG_ROM_IMAGE_SIZE = 128 * 1024
option COREBOOT_EXTRA_VERSION = ".0Fallback"
payload __PAYLOAD__
end
-buildrom ./coreboot.rom ROM_SIZE "image"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "image"
payload ../payload.elf
end
-buildrom ./coreboot.rom ROM_SIZE "image"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "image"
mainboard VENDOR/MAINBOARD
option CC="CROSSCC"
-option CROSS_COMPILE="CROSS_PREFIX"
-option HOSTCC="CROSS_HOSTCC"
+option CONFIG_CROSS_COMPILE="CROSS_PREFIX"
+option CONFIG_HOSTCC="CROSS_HOSTCC"
-option ROM_SIZE=512*1024
+option CONFIG_ROM_SIZE=512*1024
__COMPRESSION__
__LOGLEVEL__
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=1
option COREBOOT_EXTRA_VERSION=".0-fallback"
payload __PAYLOAD__
end
-buildrom ./coreboot.rom ROM_SIZE "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback"
#pci_rom $(TOP)/via-cx700.rom vendor_id=0x1106 device_id=0x3157
target via_vt8454c
mainboard via/vt8454c
-option MAXIMUM_CONSOLE_LOGLEVEL=5
-option DEFAULT_CONSOLE_LOGLEVEL=5
+option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=5
+option CONFIG_DEFAULT_CONSOLE_LOGLEVEL=5
-option ROM_SIZE=(512-64)*1024
+option CONFIG_ROM_SIZE=(512-64)*1024
romimage "normal"
- option USE_FALLBACK_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=0
option COREBOOT_EXTRA_VERSION=".0-normal"
payload $(HOME)/payload.elf
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=1
option COREBOOT_EXTRA_VERSION=".0-fallback"
payload $(HOME)/payload.elf
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
mainboard VENDOR/MAINBOARD
option CC="CROSSCC"
-option CROSS_COMPILE="CROSS_PREFIX"
-option HOSTCC="CROSS_HOSTCC"
+option CONFIG_CROSS_COMPILE="CROSS_PREFIX"
+option CONFIG_HOSTCC="CROSS_HOSTCC"
__COMPRESSION__
__LOGLEVEL__
if [ "$TARCH" == i386 ] ; then
cat <<EOF
romimage "normal"
- option USE_FALLBACK_IMAGE=0
+ option CONFIG_USE_FALLBACK_IMAGE=0
if CONFIG_CBFS
else
- option ROM_IMAGE_SIZE=0x17000
+ option CONFIG_ROM_IMAGE_SIZE=0x17000
end
option COREBOOT_EXTRA_VERSION=".0-normal"
payload __PAYLOAD__
end
romimage "fallback"
- option USE_FALLBACK_IMAGE=1
+ option CONFIG_USE_FALLBACK_IMAGE=1
if CONFIG_CBFS
else
- option ROM_IMAGE_SIZE=0x17000
+ option CONFIG_ROM_IMAGE_SIZE=0x17000
end
option COREBOOT_EXTRA_VERSION=".0-fallback"
payload __PAYLOAD__
end
-buildrom ./coreboot.rom ROM_SIZE "normal" "fallback"
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback"
EOF
else
cat <<EOF
fi
if [ "$loglevel" != "default" ]; then
- LOGLEVEL1="option MAXIMUM_CONSOLE_LOGLEVEL=$loglevel"
- LOGLEVEL2="option DEFAULT_CONSOLE_LOGLEVEL=$loglevel"
+ LOGLEVEL1="option CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=$loglevel"
+ LOGLEVEL2="option CONFIG_DEFAULT_CONSOLE_LOGLEVEL=$loglevel"
else
LOGLEVEL1="# no loglevel override"
LOGLEVEL2=""
TARGETS := $(foreach VENDOR, $(VENDORS), $(addprefix $(VENDOR)/, $($(VENDOR)_BOARDS)))
# The following delayed-evalutate variables are only to be used in rule commands.
-MAINBOARD = $(TOP)/src/mainboard/$(shell grep ^mainboard $(dir $*)/Config.lb|grep -Eo [-[:alnum:]_/]+[[:space:]]?$$)
+CONFIG_MAINBOARD = $(TOP)/src/mainboard/$(shell grep ^mainboard $(dir $*)/Config.lb|grep -Eo [-[:alnum:]_/]+[[:space:]]?$$)
IMAGE_DIR = $(firstword $(shell grep -Eo ^romimage[[:space:]]+\"[[:alnum:]_-/]+ $(dir $*)/Config.lb|sed -r s/romimage[[:space:]]+\"//))
# Evaluate one assignment to variable "$1" from file "$2"
OBJ=$(COMMANDS) cbfstool.o util.o fs.o
INC=cbfstool.h cbfs.h
-HOSTCC ?= gcc
+CONFIG_HOSTCC ?= gcc
HOSTCXX ?= g++
CFLAGS=-g -Wall -W -Werror
all: $(obj)/cbfstool $(obj)/tools/cbfs-mkpayload $(obj)/tools/cbfs-mkstage
$(obj)/cbfstool: $(patsubst %,$(obj)/%,$(OBJ))
- $(HOSTCC) -o $@ $(patsubst %,$(obj)/%,$(OBJ))
+ $(CONFIG_HOSTCC) -o $@ $(patsubst %,$(obj)/%,$(OBJ))
tobj = $(obj)/tools
tsrc = $(shell pwd)/tools
include $(tsrc)/Makefile
$(obj)/%.o: %.c $(INC)
- $(HOSTCC) $(CFLAGS) -c -o $@ $<
+ $(CONFIG_HOSTCC) $(CFLAGS) -c -o $@ $<
install: $(obj)/cbfstool $(obj)/tools/cbfs-mkpayload $(obj)/tools/cbfs-mkstage
@ install -d $(DESTDIR)
$(HOSTCXX) $(CFLAGS) -o $@ $^
$(tobj)/%.o: %.c
- $(HOSTCC) $(CFLAGS) -c -o $@ $<
+ $(CONFIG_HOSTCC) $(CFLAGS) -c -o $@ $<
tools-clean:
rm -f $(tobj)/cbfs-mkpayload.o $(tobj)/cbfs-mkstage.o $(patsubst %,$(tobj)/%,$(COMMON))
if (type == 'S'):
# for .S, .o depends on .s
file.write("%s: %s.s\n" % (obj[0], obj[3]))
- file.write("\t$(CC) -c $(CPU_OPT) -o $@ $<\n")
+ file.write("\t$(CC) -c $(CONFIG_CPU_OPT) -o $@ $<\n")
# and .s depends on .S
file.write("%s.s: %s\n" % (obj[3], source))
# Note: next 2 lines are ONE output line!
global curimage
global bootblocksize
mainboard()
- imagesize = getoption("ROM_IMAGE_SIZE", curimage)
+ imagesize = getoption("CONFIG_ROM_IMAGE_SIZE", curimage)
bootblocksize += imagesize
print "End ROMIMAGE"
curimage = 0
full_mainboard_path = os.path.join(treetop, 'src', 'mainboard', path)
vendor = re.sub("/.*", "", path)
part_number = re.sub("[^/]*/", "", path)
- setdefault('MAINBOARD', full_mainboard_path, 0)
- setdefault('MAINBOARD_VENDOR', vendor, 0)
- setdefault('MAINBOARD_PART_NUMBER', part_number, 0)
+ setdefault('CONFIG_MAINBOARD', full_mainboard_path, 0)
+ setdefault('CONFIG_MAINBOARD_VENDOR', vendor, 0)
+ setdefault('CONFIG_MAINBOARD_PART_NUMBER', part_number, 0)
def mainboard():
global curimage, dirstack, partstack
def setarch(my_arch):
"""arch is 'different' ... darn it."""
global curimage
- print "SETTING ARCH %s\n" % my_arch
+ print "SETTING CONFIG_ARCH %s\n" % my_arch
curimage.setarch(my_arch)
- setdefault('ARCH', my_arch, 1)
+ setdefault('CONFIG_ARCH', my_arch, 1)
part('arch', my_arch, 'Config.lb', 0)
def doconfigfile(path, confdir, file, rule):
token ACTION: 'action'
token ADDACTION: 'addaction'
token ALWAYS: 'always'
- token ARCH: 'arch'
+ token CONFIG_ARCH: 'arch'
token BUILDROM: 'buildrom'
token COMMENT: 'comment'
token CONFIG: 'config'
token IRQ: 'irq'
token LDSCRIPT: 'ldscript'
token LOADOPTIONS: 'loadoptions'
- token MAINBOARD: 'mainboard'
+ token CONFIG_MAINBOARD: 'mainboard'
token MAINBOARDINIT: 'mainboardinit'
token MAKEDEFINE: 'makedefine'
token MAKERULE: 'makerule'
] {{ if (C): part(parttype, partid, 'Config.lb', name) }}
partend<<C>>
- rule arch<<C>>: ARCH ID {{ if (C): setarch(ID) }}
+ rule arch<<C>>: CONFIG_ARCH ID {{ if (C): setarch(ID) }}
partend<<C>>
rule mainboardinit<<C>>:
rule payload<<C>>: PAYLOAD DIRPATH {{ if (C): payload(DIRPATH) }}
rule mainboard:
- MAINBOARD PATH {{ mainboardsetup(PATH) }}
+ CONFIG_MAINBOARD PATH {{ mainboardsetup(PATH) }}
rule romif<<C>>: IF ID {{ c = lookup(ID) }}
(romstmt<<C and c>>)*
file.write(" %s/coreboot.rom " % j)
file.write("\n")
- romsize = getoption("ROM_SIZE", image)
+ romsize = getoption("CONFIG_ROM_SIZE", image)
file.write("\n\trm -f %s\n" %(i.name))
exit(1);
}
/* And since we are not ready to be fully general purpose yet.. */
- if ((cs->range_start/8) != LB_CKS_RANGE_START) {
+ if ((cs->range_start/8) != CONFIG_LB_CKS_RANGE_START) {
fprintf(stderr, "Error - Range start(%d) does not match define(%d) in line\n%s\n",
- cs->range_start/8, LB_CKS_RANGE_START, line);
+ cs->range_start/8, CONFIG_LB_CKS_RANGE_START, line);
exit(1);
}
- if ((cs->range_end/8) != LB_CKS_RANGE_END) {
+ if ((cs->range_end/8) != CONFIG_LB_CKS_RANGE_END) {
fprintf(stderr, "Error - Range end (%d) does not match define (%d) in line\n%s\n",
- (cs->range_end/8), LB_CKS_RANGE_END, line);
+ (cs->range_end/8), CONFIG_LB_CKS_RANGE_END, line);
exit(1);
}
- if ((cs->location/8) != LB_CKS_LOC) {
+ if ((cs->location/8) != CONFIG_LB_CKS_LOC) {
fprintf(stderr, "Error - Location does not match define in line\n%s\n", line);
exit(1);
}
}
/* Base Address */
-#ifndef TTYS0_BASE
-#define TTYS0_BASE 0x3f8
+#ifndef CONFIG_TTYS0_BASE
+#define CONFIG_TTYS0_BASE 0x3f8
#endif
-#ifndef TTYS0_BAUD
-#define TTYS0_BAUD 115200
+#ifndef CONFIG_TTYS0_BAUD
+#define CONFIG_TTYS0_BAUD 115200
#endif
-#if ((115200%TTYS0_BAUD) != 0)
+#if ((115200%CONFIG_TTYS0_BAUD) != 0)
#error Bad ttys0 baud rate
#endif
-#if TTYS0_BAUD == 115200
-#define TTYS0_DIV (1)
+#if CONFIG_TTYS0_BAUD == 115200
+#define CONFIG_TTYS0_DIV (1)
#else
-#define TTYS0_DIV (115200/TTYS0_BAUD)
+#define CONFIG_TTYS0_DIV (115200/CONFIG_TTYS0_BAUD)
#endif
/* Line Control Settings */
-#ifndef TTYS0_LCS
+#ifndef CONFIG_TTYS0_LCS
/* Set 8bit, 1 stop bit, no parity */
-#define TTYS0_LCS 0x3
+#define CONFIG_TTYS0_LCS 0x3
#endif
-#define UART_LCS TTYS0_LCS
+#define UART_LCS CONFIG_TTYS0_LCS
/* Data */
#define UART_RBR 0x00
int uart_can_tx_byte(void)
{
- return inb(TTYS0_BASE + UART_LSR) & 0x20;
+ return inb(CONFIG_TTYS0_BASE + UART_LSR) & 0x20;
}
void uart_wait_to_tx_byte(void)
void uart_wait_until_sent(void)
{
- while(!(inb(TTYS0_BASE + UART_LSR) & 0x40))
+ while(!(inb(CONFIG_TTYS0_BASE + UART_LSR) & 0x40))
;
}
static void uart_tx_byte(unsigned char data)
{
uart_wait_to_tx_byte();
- outb(data, TTYS0_BASE + UART_TBR);
+ outb(data, CONFIG_TTYS0_BASE + UART_TBR);
/* Make certain the data clears the fifos */
uart_wait_until_sent();
}
void uart_init(void)
{
/* disable interrupts */
- outb(0x0, TTYS0_BASE + UART_IER);
+ outb(0x0, CONFIG_TTYS0_BASE + UART_IER);
/* enable fifo's */
- outb(0x01, TTYS0_BASE + UART_FCR);
+ outb(0x01, CONFIG_TTYS0_BASE + UART_FCR);
/* Set Baud Rate Divisor to 12 ==> 115200 Baud */
- outb(0x80 | UART_LCS, TTYS0_BASE + UART_LCR);
- outb(TTYS0_DIV & 0xFF, TTYS0_BASE + UART_DLL);
- outb((TTYS0_DIV >> 8) & 0xFF, TTYS0_BASE + UART_DLM);
- outb(UART_LCS, TTYS0_BASE + UART_LCR);
+ outb(0x80 | UART_LCS, CONFIG_TTYS0_BASE + UART_LCR);
+ outb(CONFIG_TTYS0_DIV & 0xFF, CONFIG_TTYS0_BASE + UART_DLL);
+ outb((CONFIG_TTYS0_DIV >> 8) & 0xFF, CONFIG_TTYS0_BASE + UART_DLM);
+ outb(UART_LCS, CONFIG_TTYS0_BASE + UART_LCR);
}
}
/* Base Address */
-#ifndef TTYS0_BASE
-#define TTYS0_BASE 0x3f8
+#ifndef CONFIG_TTYS0_BASE
+#define CONFIG_TTYS0_BASE 0x3f8
#endif
-#ifndef TTYS0_BAUD
-#define TTYS0_BAUD 115200
+#ifndef CONFIG_TTYS0_BAUD
+#define CONFIG_TTYS0_BAUD 115200
#endif
-#if ((115200%TTYS0_BAUD) != 0)
+#if ((115200%CONFIG_TTYS0_BAUD) != 0)
#error Bad ttys0 baud rate
#endif
-#if TTYS0_BAUD == 115200
-#define TTYS0_DIV (1)
+#if CONFIG_TTYS0_BAUD == 115200
+#define CONFIG_TTYS0_DIV (1)
#else
-#define TTYS0_DIV (115200/TTYS0_BAUD)
+#define CONFIG_TTYS0_DIV (115200/CONFIG_TTYS0_BAUD)
#endif
/* Line Control Settings */
-#ifndef TTYS0_LCS
+#ifndef CONFIG_TTYS0_LCS
/* Set 8bit, 1 stop bit, no parity */
-#define TTYS0_LCS 0x3
+#define CONFIG_TTYS0_LCS 0x3
#endif
-#define UART_LCS TTYS0_LCS
+#define UART_LCS CONFIG_TTYS0_LCS
/* Data */
#define UART_RBR 0x00
int uart_can_tx_byte(void)
{
- return inb(TTYS0_BASE + UART_LSR) & 0x20;
+ return inb(CONFIG_TTYS0_BASE + UART_LSR) & 0x20;
}
void uart_wait_to_tx_byte(void)
void uart_wait_until_sent(void)
{
- while(!(inb(TTYS0_BASE + UART_LSR) & 0x40))
+ while(!(inb(CONFIG_TTYS0_BASE + UART_LSR) & 0x40))
;
}
static void uart_tx_byte(unsigned char data)
{
uart_wait_to_tx_byte();
- outb(data, TTYS0_BASE + UART_TBR);
+ outb(data, CONFIG_TTYS0_BASE + UART_TBR);
/* Make certain the data clears the fifos */
uart_wait_until_sent();
}
void uart_init(void)
{
/* disable interrupts */
- outb(0x0, TTYS0_BASE + UART_IER);
+ outb(0x0, CONFIG_TTYS0_BASE + UART_IER);
/* enable fifo's */
- outb(0x01, TTYS0_BASE + UART_FCR);
+ outb(0x01, CONFIG_TTYS0_BASE + UART_FCR);
/* Set Baud Rate Divisor to 12 ==> 115200 Baud */
- outb(0x80 | UART_LCS, TTYS0_BASE + UART_LCR);
- outb(TTYS0_DIV & 0xFF, TTYS0_BASE + UART_DLL);
- outb((TTYS0_DIV >> 8) & 0xFF, TTYS0_BASE + UART_DLM);
- outb(UART_LCS, TTYS0_BASE + UART_LCR);
+ outb(0x80 | UART_LCS, CONFIG_TTYS0_BASE + UART_LCR);
+ outb(CONFIG_TTYS0_DIV & 0xFF, CONFIG_TTYS0_BASE + UART_DLL);
+ outb((CONFIG_TTYS0_DIV >> 8) & 0xFF, CONFIG_TTYS0_BASE + UART_DLM);
+ outb(UART_LCS, CONFIG_TTYS0_BASE + UART_LCR);
}
}
/* Base Address */
-#ifndef TTYS0_BASE
-#define TTYS0_BASE 0x3f8
+#ifndef CONFIG_TTYS0_BASE
+#define CONFIG_TTYS0_BASE 0x3f8
#endif
-#ifndef TTYS0_BAUD
-#define TTYS0_BAUD 115200
+#ifndef CONFIG_TTYS0_BAUD
+#define CONFIG_TTYS0_BAUD 115200
#endif
-#if ((115200%TTYS0_BAUD) != 0)
+#if ((115200%CONFIG_TTYS0_BAUD) != 0)
#error Bad ttys0 baud rate
#endif
-#if TTYS0_BAUD == 115200
-#define TTYS0_DIV (1)
+#if CONFIG_TTYS0_BAUD == 115200
+#define CONFIG_TTYS0_DIV (1)
#else
-#define TTYS0_DIV (115200/TTYS0_BAUD)
+#define CONFIG_TTYS0_DIV (115200/CONFIG_TTYS0_BAUD)
#endif
/* Line Control Settings */
-#ifndef TTYS0_LCS
+#ifndef CONFIG_TTYS0_LCS
/* Set 8bit, 1 stop bit, no parity */
-#define TTYS0_LCS 0x3
+#define CONFIG_TTYS0_LCS 0x3
#endif
-#define UART_LCS TTYS0_LCS
+#define UART_LCS CONFIG_TTYS0_LCS
/* Data */
#define UART_RBR 0x00
int uart_can_tx_byte(void)
{
- return inb(TTYS0_BASE + UART_LSR) & 0x20;
+ return inb(CONFIG_TTYS0_BASE + UART_LSR) & 0x20;
}
void uart_wait_to_tx_byte(void)
void uart_wait_until_sent(void)
{
- while(!(inb(TTYS0_BASE + UART_LSR) & 0x40))
+ while(!(inb(CONFIG_TTYS0_BASE + UART_LSR) & 0x40))
;
}
static void uart_tx_byte(unsigned char data)
{
uart_wait_to_tx_byte();
- outb(data, TTYS0_BASE + UART_TBR);
+ outb(data, CONFIG_TTYS0_BASE + UART_TBR);
/* Make certain the data clears the fifos */
uart_wait_until_sent();
}
void uart_init(void)
{
/* disable interrupts */
- outb(0x0, TTYS0_BASE + UART_IER);
+ outb(0x0, CONFIG_TTYS0_BASE + UART_IER);
/* enable fifo's */
- outb(0x01, TTYS0_BASE + UART_FCR);
+ outb(0x01, CONFIG_TTYS0_BASE + UART_FCR);
/* Set Baud Rate Divisor to 12 ==> 115200 Baud */
- outb(0x80 | UART_LCS, TTYS0_BASE + UART_LCR);
- outb(TTYS0_DIV & 0xFF, TTYS0_BASE + UART_DLL);
- outb((TTYS0_DIV >> 8) & 0xFF, TTYS0_BASE + UART_DLM);
- outb(UART_LCS, TTYS0_BASE + UART_LCR);
+ outb(0x80 | UART_LCS, CONFIG_TTYS0_BASE + UART_LCR);
+ outb(CONFIG_TTYS0_DIV & 0xFF, CONFIG_TTYS0_BASE + UART_DLL);
+ outb((CONFIG_TTYS0_DIV >> 8) & 0xFF, CONFIG_TTYS0_BASE + UART_DLM);
+ outb(UART_LCS, CONFIG_TTYS0_BASE + UART_LCR);
}
}
/* Base Address */
-#ifndef TTYS0_BASE
-#define TTYS0_BASE 0x3f8
+#ifndef CONFIG_TTYS0_BASE
+#define CONFIG_TTYS0_BASE 0x3f8
#endif
-#ifndef TTYS0_BAUD
-#define TTYS0_BAUD 115200
+#ifndef CONFIG_TTYS0_BAUD
+#define CONFIG_TTYS0_BAUD 115200
#endif
-#if ((115200%TTYS0_BAUD) != 0)
+#if ((115200%CONFIG_TTYS0_BAUD) != 0)
#error Bad ttys0 baud rate
#endif
-#define TTYS0_DIV (115200/TTYS0_BAUD)
+#define CONFIG_TTYS0_DIV (115200/CONFIG_TTYS0_BAUD)
/* Line Control Settings */
-#ifndef TTYS0_LCS
+#ifndef CONFIG_TTYS0_LCS
/* Set 8bit, 1 stop bit, no parity */
-#define TTYS0_LCS 0x3
+#define CONFIG_TTYS0_LCS 0x3
#endif
-#define UART_LCS TTYS0_LCS
+#define UART_LCS CONFIG_TTYS0_LCS
/* Data */
#define UART_RBR 0x00
int uart_can_tx_byte(void)
{
- return inb(TTYS0_BASE + UART_LSR) & 0x20;
+ return inb(CONFIG_TTYS0_BASE + UART_LSR) & 0x20;
}
void uart_wait_to_tx_byte(void)
void uart_wait_until_sent(void)
{
- while(!(inb(TTYS0_BASE + UART_LSR) & 0x40))
+ while(!(inb(CONFIG_TTYS0_BASE + UART_LSR) & 0x40))
;
}
void uart_tx_byte(unsigned char data)
{
uart_wait_to_tx_byte();
- outb(data, TTYS0_BASE + UART_TBR);
+ outb(data, CONFIG_TTYS0_BASE + UART_TBR);
/* Make certain the data clears the fifos */
uart_wait_until_sent();
}
void uart_init(void)
{
/* disable interrupts */
- outb(0x0, TTYS0_BASE + UART_IER);
+ outb(0x0, CONFIG_TTYS0_BASE + UART_IER);
/* enable fifo's */
- outb(0x01, TTYS0_BASE + UART_FCR);
+ outb(0x01, CONFIG_TTYS0_BASE + UART_FCR);
/* Set Baud Rate Divisor to 12 ==> 115200 Baud */
- outb(0x80 | UART_LCS, TTYS0_BASE + UART_LCR);
- outb(TTYS0_DIV & 0xFF, TTYS0_BASE + UART_DLL);
- outb((TTYS0_DIV >> 8) & 0xFF, TTYS0_BASE + UART_DLM);
- outb(UART_LCS, TTYS0_BASE + UART_LCR);
+ outb(0x80 | UART_LCS, CONFIG_TTYS0_BASE + UART_LCR);
+ outb(CONFIG_TTYS0_DIV & 0xFF, CONFIG_TTYS0_BASE + UART_DLL);
+ outb((CONFIG_TTYS0_DIV >> 8) & 0xFF, CONFIG_TTYS0_BASE + UART_DLM);
+ outb(UART_LCS, CONFIG_TTYS0_BASE + UART_LCR);
}
void __console_tx_char(unsigned char byte)
}
/* Base Address */
-#ifndef TTYS0_BASE
-#define TTYS0_BASE 0x3f8
+#ifndef CONFIG_TTYS0_BASE
+#define CONFIG_TTYS0_BASE 0x3f8
#endif
-#ifndef TTYS0_BAUD
-#define TTYS0_BAUD 115200
+#ifndef CONFIG_TTYS0_BAUD
+#define CONFIG_TTYS0_BAUD 115200
#endif
-#if ((115200%TTYS0_BAUD) != 0)
+#if ((115200%CONFIG_TTYS0_BAUD) != 0)
#error Bad ttys0 baud rate
#endif
-#define TTYS0_DIV (115200/TTYS0_BAUD)
+#define CONFIG_TTYS0_DIV (115200/CONFIG_TTYS0_BAUD)
/* Line Control Settings */
-#ifndef TTYS0_LCS
+#ifndef CONFIG_TTYS0_LCS
/* Set 8bit, 1 stop bit, no parity */
-#define TTYS0_LCS 0x3
+#define CONFIG_TTYS0_LCS 0x3
#endif
-#define UART_LCS TTYS0_LCS
+#define UART_LCS CONFIG_TTYS0_LCS
/* Data */
#define UART_RBR 0x00
int uart_can_tx_byte(void)
{
- return inb(TTYS0_BASE + UART_LSR) & 0x20;
+ return inb(CONFIG_TTYS0_BASE + UART_LSR) & 0x20;
}
void uart_wait_to_tx_byte(void)
void uart_wait_until_sent(void)
{
- while(!(inb(TTYS0_BASE + UART_LSR) & 0x40))
+ while(!(inb(CONFIG_TTYS0_BASE + UART_LSR) & 0x40))
;
}
void uart_tx_byte(unsigned char data)
{
uart_wait_to_tx_byte();
- outb(data, TTYS0_BASE + UART_TBR);
+ outb(data, CONFIG_TTYS0_BASE + UART_TBR);
/* Make certain the data clears the fifos */
uart_wait_until_sent();
}
void uart_init(void)
{
/* disable interrupts */
- outb(0x0, TTYS0_BASE + UART_IER);
+ outb(0x0, CONFIG_TTYS0_BASE + UART_IER);
/* enable fifo's */
- outb(0x01, TTYS0_BASE + UART_FCR);
+ outb(0x01, CONFIG_TTYS0_BASE + UART_FCR);
/* Set Baud Rate Divisor to 12 ==> 115200 Baud */
- outb(0x80 | UART_LCS, TTYS0_BASE + UART_LCR);
- outb(TTYS0_DIV & 0xFF, TTYS0_BASE + UART_DLL);
- outb((TTYS0_DIV >> 8) & 0xFF, TTYS0_BASE + UART_DLM);
- outb(UART_LCS, TTYS0_BASE + UART_LCR);
+ outb(0x80 | UART_LCS, CONFIG_TTYS0_BASE + UART_LCR);
+ outb(CONFIG_TTYS0_DIV & 0xFF, CONFIG_TTYS0_BASE + UART_DLL);
+ outb((CONFIG_TTYS0_DIV >> 8) & 0xFF, CONFIG_TTYS0_BASE + UART_DLM);
+ outb(UART_LCS, CONFIG_TTYS0_BASE + UART_LCR);
}
void __console_tx_char(unsigned char byte)
}
/* Base Address */
-#ifndef TTYS0_BASE
-#define TTYS0_BASE 0x3f8
+#ifndef CONFIG_TTYS0_BASE
+#define CONFIG_TTYS0_BASE 0x3f8
#endif
-#ifndef TTYS0_BAUD
-#define TTYS0_BAUD 115200
+#ifndef CONFIG_TTYS0_BAUD
+#define CONFIG_TTYS0_BAUD 115200
#endif
-#if ((115200%TTYS0_BAUD) != 0)
+#if ((115200%CONFIG_TTYS0_BAUD) != 0)
#error Bad ttys0 baud rate
#endif
-#define TTYS0_DIV (115200/TTYS0_BAUD)
+#define CONFIG_TTYS0_DIV (115200/CONFIG_TTYS0_BAUD)
/* Line Control Settings */
-#ifndef TTYS0_LCS
+#ifndef CONFIG_TTYS0_LCS
/* Set 8bit, 1 stop bit, no parity */
-#define TTYS0_LCS 0x3
+#define CONFIG_TTYS0_LCS 0x3
#endif
-#define UART_LCS TTYS0_LCS
+#define UART_LCS CONFIG_TTYS0_LCS
/* Data */
#define UART_RBR 0x00
int uart_can_tx_byte(void)
{
- return inb(TTYS0_BASE + UART_LSR) & 0x20;
+ return inb(CONFIG_TTYS0_BASE + UART_LSR) & 0x20;
}
void uart_wait_to_tx_byte(void)
void uart_wait_until_sent(void)
{
- while(!(inb(TTYS0_BASE + UART_LSR) & 0x40))
+ while(!(inb(CONFIG_TTYS0_BASE + UART_LSR) & 0x40))
;
}
void uart_tx_byte(unsigned char data)
{
uart_wait_to_tx_byte();
- outb(data, TTYS0_BASE + UART_TBR);
+ outb(data, CONFIG_TTYS0_BASE + UART_TBR);
/* Make certain the data clears the fifos */
uart_wait_until_sent();
}
void uart_init(void)
{
/* disable interrupts */
- outb(0x0, TTYS0_BASE + UART_IER);
+ outb(0x0, CONFIG_TTYS0_BASE + UART_IER);
/* enable fifo's */
- outb(0x01, TTYS0_BASE + UART_FCR);
+ outb(0x01, CONFIG_TTYS0_BASE + UART_FCR);
/* Set Baud Rate Divisor to 12 ==> 115200 Baud */
- outb(0x80 | UART_LCS, TTYS0_BASE + UART_LCR);
- outb(TTYS0_DIV & 0xFF, TTYS0_BASE + UART_DLL);
- outb((TTYS0_DIV >> 8) & 0xFF, TTYS0_BASE + UART_DLM);
- outb(UART_LCS, TTYS0_BASE + UART_LCR);
+ outb(0x80 | UART_LCS, CONFIG_TTYS0_BASE + UART_LCR);
+ outb(CONFIG_TTYS0_DIV & 0xFF, CONFIG_TTYS0_BASE + UART_DLL);
+ outb((CONFIG_TTYS0_DIV >> 8) & 0xFF, CONFIG_TTYS0_BASE + UART_DLM);
+ outb(UART_LCS, CONFIG_TTYS0_BASE + UART_LCR);
}
void __console_tx_char(unsigned char byte)
}
/* Base Address */
-#ifndef TTYS0_BASE
-#define TTYS0_BASE 0x3f8
+#ifndef CONFIG_TTYS0_BASE
+#define CONFIG_TTYS0_BASE 0x3f8
#endif
-#ifndef TTYS0_BAUD
-#define TTYS0_BAUD 115200
+#ifndef CONFIG_TTYS0_BAUD
+#define CONFIG_TTYS0_BAUD 115200
#endif
-#if ((115200%TTYS0_BAUD) != 0)
+#if ((115200%CONFIG_TTYS0_BAUD) != 0)
#error Bad ttys0 baud rate
#endif
-#define TTYS0_DIV (115200/TTYS0_BAUD)
+#define CONFIG_TTYS0_DIV (115200/CONFIG_TTYS0_BAUD)
/* Line Control Settings */
-#ifndef TTYS0_LCS
+#ifndef CONFIG_TTYS0_LCS
/* Set 8bit, 1 stop bit, no parity */
-#define TTYS0_LCS 0x3
+#define CONFIG_TTYS0_LCS 0x3
#endif
-#define UART_LCS TTYS0_LCS
+#define UART_LCS CONFIG_TTYS0_LCS
/* Data */
#define UART_RBR 0x00
int uart_can_tx_byte(void)
{
- return inb(TTYS0_BASE + UART_LSR) & 0x20;
+ return inb(CONFIG_TTYS0_BASE + UART_LSR) & 0x20;
}
void uart_wait_to_tx_byte(void)
void uart_wait_until_sent(void)
{
- while(!(inb(TTYS0_BASE + UART_LSR) & 0x40))
+ while(!(inb(CONFIG_TTYS0_BASE + UART_LSR) & 0x40))
;
}
void uart_tx_byte(unsigned char data)
{
uart_wait_to_tx_byte();
- outb(data, TTYS0_BASE + UART_TBR);
+ outb(data, CONFIG_TTYS0_BASE + UART_TBR);
/* Make certain the data clears the fifos */
uart_wait_until_sent();
}
}
/* Base Address */
-#ifndef TTYS0_BASE
-#define TTYS0_BASE 0x3f8
+#ifndef CONFIG_TTYS0_BASE
+#define CONFIG_TTYS0_BASE 0x3f8
#endif
-#ifndef TTYS0_BAUD
-#define TTYS0_BAUD 115200
+#ifndef CONFIG_TTYS0_BAUD
+#define CONFIG_TTYS0_BAUD 115200
#endif
-#if ((115200%TTYS0_BAUD) != 0)
+#if ((115200%CONFIG_TTYS0_BAUD) != 0)
#error Bad ttys0 baud rate
#endif
-#define TTYS0_DIV (115200/TTYS0_BAUD)
+#define CONFIG_TTYS0_DIV (115200/CONFIG_TTYS0_BAUD)
/* Line Control Settings */
-#ifndef TTYS0_LCS
+#ifndef CONFIG_TTYS0_LCS
/* Set 8bit, 1 stop bit, no parity */
-#define TTYS0_LCS 0x3
+#define CONFIG_TTYS0_LCS 0x3
#endif
-#define UART_LCS TTYS0_LCS
+#define UART_LCS CONFIG_TTYS0_LCS
/* Data */
#define UART_RBR 0x00
int uart_can_tx_byte(void)
{
- return inb(TTYS0_BASE + UART_LSR) & 0x20;
+ return inb(CONFIG_TTYS0_BASE + UART_LSR) & 0x20;
}
void uart_wait_to_tx_byte(void)
void uart_wait_until_sent(void)
{
- while(!(inb(TTYS0_BASE + UART_LSR) & 0x40))
+ while(!(inb(CONFIG_TTYS0_BASE + UART_LSR) & 0x40))
;
}
void uart_tx_byte(unsigned char data)
{
uart_wait_to_tx_byte();
- outb(data, TTYS0_BASE + UART_TBR);
+ outb(data, CONFIG_TTYS0_BASE + UART_TBR);
/* Make certain the data clears the fifos */
uart_wait_until_sent();
}
/* Base Address */
-#ifndef TTYS0_BASE
-#define TTYS0_BASE 0x3f8
+#ifndef CONFIG_TTYS0_BASE
+#define CONFIG_TTYS0_BASE 0x3f8
#endif
-#ifndef TTYS0_BAUD
-#define TTYS0_BAUD 115200
+#ifndef CONFIG_TTYS0_BAUD
+#define CONFIG_TTYS0_BAUD 115200
#endif
-#if ((115200%TTYS0_BAUD) != 0)
+#if ((115200%CONFIG_TTYS0_BAUD) != 0)
#error Bad ttys0 baud rate
#endif
-#define TTYS0_DIV (115200/TTYS0_BAUD)
+#define CONFIG_TTYS0_DIV (115200/CONFIG_TTYS0_BAUD)
/* Line Control Settings */
-#ifndef TTYS0_LCS
+#ifndef CONFIG_TTYS0_LCS
/* Set 8bit, 1 stop bit, no parity */
-#define TTYS0_LCS 0x3
+#define CONFIG_TTYS0_LCS 0x3
#endif
-#define UART_LCS TTYS0_LCS
+#define UART_LCS CONFIG_TTYS0_LCS
/* Data */
#define UART_RBR 0x00
int uart_can_tx_byte(void)
{
- return inb(TTYS0_BASE + UART_LSR) & 0x20;
+ return inb(CONFIG_TTYS0_BASE + UART_LSR) & 0x20;
}
void uart_wait_to_tx_byte(void)
void uart_wait_until_sent(void)
{
- while(!(inb(TTYS0_BASE + UART_LSR) & 0x40))
+ while(!(inb(CONFIG_TTYS0_BASE + UART_LSR) & 0x40))
;
}
void uart_tx_byte(unsigned char data)
{
uart_wait_to_tx_byte();
- outb(data, TTYS0_BASE + UART_TBR);
+ outb(data, CONFIG_TTYS0_BASE + UART_TBR);
/* Make certain the data clears the fifos */
uart_wait_until_sent();
}
void uart_init(void)
{
/* disable interrupts */
- outb(0x0, TTYS0_BASE + UART_IER);
+ outb(0x0, CONFIG_TTYS0_BASE + UART_IER);
/* enable fifo's */
- outb(0x01, TTYS0_BASE + UART_FCR);
+ outb(0x01, CONFIG_TTYS0_BASE + UART_FCR);
/* Set Baud Rate Divisor to 12 ==> 115200 Baud */
- outb(0x80 | UART_LCS, TTYS0_BASE + UART_LCR);
- outb(TTYS0_DIV & 0xFF, TTYS0_BASE + UART_DLL);
- outb((TTYS0_DIV >> 8) & 0xFF, TTYS0_BASE + UART_DLM);
- outb(UART_LCS, TTYS0_BASE + UART_LCR);
+ outb(0x80 | UART_LCS, CONFIG_TTYS0_BASE + UART_LCR);
+ outb(CONFIG_TTYS0_DIV & 0xFF, CONFIG_TTYS0_BASE + UART_DLL);
+ outb((CONFIG_TTYS0_DIV >> 8) & 0xFF, CONFIG_TTYS0_BASE + UART_DLM);
+ outb(UART_LCS, CONFIG_TTYS0_BASE + UART_LCR);
}
void __console_tx_char(unsigned char byte)
}
/* Base Address */
-#ifndef TTYS0_BASE
-#define TTYS0_BASE 0x3f8
+#ifndef CONFIG_TTYS0_BASE
+#define CONFIG_TTYS0_BASE 0x3f8
#endif
-#ifndef TTYS0_BAUD
-#define TTYS0_BAUD 115200
+#ifndef CONFIG_TTYS0_BAUD
+#define CONFIG_TTYS0_BAUD 115200
#endif
-#if ((115200%TTYS0_BAUD) != 0)
+#if ((115200%CONFIG_TTYS0_BAUD) != 0)
#error Bad ttys0 baud rate
#endif
-#if TTYS0_BAUD == 115200
-#define TTYS0_DIV (1)
+#if CONFIG_TTYS0_BAUD == 115200
+#define CONFIG_TTYS0_DIV (1)
#else
-#define TTYS0_DIV (115200/TTYS0_BAUD)
+#define CONFIG_TTYS0_DIV (115200/CONFIG_TTYS0_BAUD)
#endif
/* Line Control Settings */
-#ifndef TTYS0_LCS
+#ifndef CONFIG_TTYS0_LCS
/* Set 8bit, 1 stop bit, no parity */
-#define TTYS0_LCS 0x3
+#define CONFIG_TTYS0_LCS 0x3
#endif
-#define UART_LCS TTYS0_LCS
+#define UART_LCS CONFIG_TTYS0_LCS
/* Data */
#define UART_RBR 0x00
int uart_can_tx_byte(void)
{
- return inb(TTYS0_BASE + UART_LSR) & 0x20;
+ return inb(CONFIG_TTYS0_BASE + UART_LSR) & 0x20;
}
void uart_wait_to_tx_byte(void)
void uart_wait_until_sent(void)
{
- while(!(inb(TTYS0_BASE + UART_LSR) & 0x40))
+ while(!(inb(CONFIG_TTYS0_BASE + UART_LSR) & 0x40))
;
}
static void uart_tx_byte(unsigned char data)
{
uart_wait_to_tx_byte();
- outb(data, TTYS0_BASE + UART_TBR);
+ outb(data, CONFIG_TTYS0_BASE + UART_TBR);
/* Make certain the data clears the fifos */
uart_wait_until_sent();
}
void uart_init(void)
{
/* disable interrupts */
- outb(0x0, TTYS0_BASE + UART_IER);
+ outb(0x0, CONFIG_TTYS0_BASE + UART_IER);
/* enable fifo's */
- outb(0x01, TTYS0_BASE + UART_FCR);
+ outb(0x01, CONFIG_TTYS0_BASE + UART_FCR);
/* Set Baud Rate Divisor to 12 ==> 115200 Baud */
- outb(0x80 | UART_LCS, TTYS0_BASE + UART_LCR);
- outb(TTYS0_DIV & 0xFF, TTYS0_BASE + UART_DLL);
- outb((TTYS0_DIV >> 8) & 0xFF, TTYS0_BASE + UART_DLM);
- outb(UART_LCS, TTYS0_BASE + UART_LCR);
+ outb(0x80 | UART_LCS, CONFIG_TTYS0_BASE + UART_LCR);
+ outb(CONFIG_TTYS0_DIV & 0xFF, CONFIG_TTYS0_BASE + UART_DLL);
+ outb((CONFIG_TTYS0_DIV >> 8) & 0xFF, CONFIG_TTYS0_BASE + UART_DLM);
+ outb(UART_LCS, CONFIG_TTYS0_BASE + UART_LCR);
}
/* Base Address */
-#ifndef TTYS0_BASE
-#define TTYS0_BASE 0x3f8
+#ifndef CONFIG_TTYS0_BASE
+#define CONFIG_TTYS0_BASE 0x3f8
#endif
-#ifndef TTYS0_BAUD
-#define TTYS0_BAUD 115200
+#ifndef CONFIG_TTYS0_BAUD
+#define CONFIG_TTYS0_BAUD 115200
#endif
-#if ((115200%TTYS0_BAUD) != 0)
+#if ((115200%CONFIG_TTYS0_BAUD) != 0)
#error Bad ttys0 baud rate
#endif
-#define TTYS0_DIV (115200/TTYS0_BAUD)
+#define CONFIG_TTYS0_DIV (115200/CONFIG_TTYS0_BAUD)
/* Line Control Settings */
-#ifndef TTYS0_LCS
+#ifndef CONFIG_TTYS0_LCS
/* Set 8bit, 1 stop bit, no parity */
-#define TTYS0_LCS 0x3
+#define CONFIG_TTYS0_LCS 0x3
#endif
-#define UART_LCS TTYS0_LCS
+#define UART_LCS CONFIG_TTYS0_LCS
/* Data */
#define UART_RBR 0x00
int uart_can_tx_byte(void)
{
- return inb(TTYS0_BASE + UART_LSR) & 0x20;
+ return inb(CONFIG_TTYS0_BASE + UART_LSR) & 0x20;
}
void uart_wait_to_tx_byte(void)
void uart_wait_until_sent(void)
{
- while(!(inb(TTYS0_BASE + UART_LSR) & 0x40))
+ while(!(inb(CONFIG_TTYS0_BASE + UART_LSR) & 0x40))
;
}
void uart_tx_byte(unsigned char data)
{
uart_wait_to_tx_byte();
- outb(data, TTYS0_BASE + UART_TBR);
+ outb(data, CONFIG_TTYS0_BASE + UART_TBR);
/* Make certain the data clears the fifos */
uart_wait_until_sent();
}
void uart_init(void)
{
/* disable interrupts */
- outb(0x0, TTYS0_BASE + UART_IER);
+ outb(0x0, CONFIG_TTYS0_BASE + UART_IER);
/* enable fifo's */
- outb(0x01, TTYS0_BASE + UART_FCR);
+ outb(0x01, CONFIG_TTYS0_BASE + UART_FCR);
/* Set Baud Rate Divisor to 12 ==> 115200 Baud */
- outb(0x80 | UART_LCS, TTYS0_BASE + UART_LCR);
- outb(TTYS0_DIV & 0xFF, TTYS0_BASE + UART_DLL);
- outb((TTYS0_DIV >> 8) & 0xFF, TTYS0_BASE + UART_DLM);
- outb(UART_LCS, TTYS0_BASE + UART_LCR);
+ outb(0x80 | UART_LCS, CONFIG_TTYS0_BASE + UART_LCR);
+ outb(CONFIG_TTYS0_DIV & 0xFF, CONFIG_TTYS0_BASE + UART_DLL);
+ outb((CONFIG_TTYS0_DIV >> 8) & 0xFF, CONFIG_TTYS0_BASE + UART_DLM);
+ outb(UART_LCS, CONFIG_TTYS0_BASE + UART_LCR);
}
void __console_tx_char(unsigned char byte)
};
#endif
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
void dprint(unsigned long start, unsigned long size)
{
int i, j;
}
printf("\n");
}
-#endif /* DEBUG */
+#endif /* CONFIG_DEBUG */
#if 0
#ifndef _PC
void X86EMU_exec(void);
void X86EMU_halt_sys(void);
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
#define HALT_SYS() \
printk("halt_sys: file %s, line %d\n", __FILE__, __LINE__), \
X86EMU_halt_sys()
#endif /* X86_FPU_SUPPORT */
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
# define DECODE_PRINTINSTR32(t,mod,rh,rl) \
DECODE_PRINTF(t[(mod<<3)+(rh)]);
# define DECODE_PRINTINSTR256(t,mod,rh,rl) \
u32 mode;
volatile int intr; /* mask of pending interrupts */
int debug;
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
int check;
u16 saved_ip;
u16 saved_cs;
/*----------------------------- Implementation ----------------------------*/
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
static void print_encoded_bytes (u16 s, u16 o);
static void print_decoded_instruction (void);
* flag associated with the "execution", and we are using a copy
* of the register struct. All the major opcodes, once fully
* decoded, have the following two steps: TRACE_REGS(r,m);
- * SINGLE_STEP(r,m); which disappear if DEBUG is not defined to
+ * SINGLE_STEP(r,m); which disappear if CONFIG_DEBUG is not defined to
* the preprocessor. The TRACE_REGS macro expands to:
*
* if (debug&DEBUG_DISASSEMBLE)
}
}
-#endif /* DEBUG */
+#endif /* CONFIG_DEBUG */
void x86emu_dump_regs (void)
{
case SYSMODE_SEGOVR_SS | SYSMODE_SEG_DS_SS:
return M.x86.R_SS;
default:
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
printk("error: should not happen: multiple overrides.\n");
#endif
HALT_SYS();
u8 fetch_data_byte(
uint offset)
{
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
if (CHECK_DATA_ACCESS())
x86emu_check_data_access((u16)get_data_segment(), offset);
#endif
u16 fetch_data_word(
uint offset)
{
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
if (CHECK_DATA_ACCESS())
x86emu_check_data_access((u16)get_data_segment(), offset);
#endif
u32 fetch_data_long(
uint offset)
{
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
if (CHECK_DATA_ACCESS())
x86emu_check_data_access((u16)get_data_segment(), offset);
#endif
uint segment,
uint offset)
{
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
if (CHECK_DATA_ACCESS())
x86emu_check_data_access(segment, offset);
#endif
uint segment,
uint offset)
{
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
if (CHECK_DATA_ACCESS())
x86emu_check_data_access(segment, offset);
#endif
uint segment,
uint offset)
{
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
if (CHECK_DATA_ACCESS())
x86emu_check_data_access(segment, offset);
#endif
uint offset,
u8 val)
{
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
if (CHECK_DATA_ACCESS())
x86emu_check_data_access((u16)get_data_segment(), offset);
#endif
uint offset,
u16 val)
{
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
if (CHECK_DATA_ACCESS())
x86emu_check_data_access((u16)get_data_segment(), offset);
#endif
uint offset,
u32 val)
{
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
if (CHECK_DATA_ACCESS())
x86emu_check_data_access((u16)get_data_segment(), offset);
#endif
uint offset,
u8 val)
{
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
if (CHECK_DATA_ACCESS())
x86emu_check_data_access(segment, offset);
#endif
uint offset,
u16 val)
{
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
if (CHECK_DATA_ACCESS())
x86emu_check_data_access(segment, offset);
#endif
uint offset,
u32 val)
{
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
if (CHECK_DATA_ACCESS())
x86emu_check_data_access(segment, offset);
#endif
END_OF_INSTR_NO_TRACE();
}
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
static char *x86emu_fpu_op_d9_tab[] = {
"FLD\tDWORD PTR ", "ESC_D9\t", "FST\tDWORD PTR ", "FSTP\tDWORD PTR ",
"FRNDINT", "FSCALE", "ESC_D9", "ESC_D9",
};
-#endif /* DEBUG */
+#endif /* CONFIG_DEBUG */
/* opcode=0xd9 */
void x86emuOp_esc_coprocess_d9(u8 X86EMU_UNUSED(op1))
START_OF_INSTR();
FETCH_DECODE_MODRM(mod, rh, rl);
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
if (mod != 3) {
DECODE_PRINTINSTR32(x86emu_fpu_op_d9_tab, mod, rh, rl);
} else {
END_OF_INSTR_NO_TRACE();
}
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
char *x86emu_fpu_op_da_tab[] = {
"FIADD\tDWORD PTR ", "FIMUL\tDWORD PTR ", "FICOM\tDWORD PTR ",
"ESC_DA ", "ESC_DA ", "ESC_DA ", "ESC_DA ",
};
-#endif /* DEBUG */
+#endif /* CONFIG_DEBUG */
/* opcode=0xda */
void x86emuOp_esc_coprocess_da(u8 X86EMU_UNUSED(op1))
END_OF_INSTR_NO_TRACE();
}
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
char *x86emu_fpu_op_db_tab[] = {
"FILD\tDWORD PTR ", "ESC_DB\t19", "FIST\tDWORD PTR ", "FISTP\tDWORD PTR ",
"ESC_DB\t1C", "FLD\tTBYTE PTR ", "ESC_DB\t1E", "FSTP\tTBYTE PTR ",
};
-#endif /* DEBUG */
+#endif /* CONFIG_DEBUG */
/* opcode=0xdb */
void x86emuOp_esc_coprocess_db(u8 X86EMU_UNUSED(op1))
START_OF_INSTR();
FETCH_DECODE_MODRM(mod, rh, rl);
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
if (mod != 3) {
DECODE_PRINTINSTR32(x86emu_fpu_op_db_tab, mod, rh, rl);
} else if (rh == 4) { /* === 11 10 0 nnn */
} else {
DECODE_PRINTF2("ESC_DB %0x\n", (mod << 6) + (rh << 3) + (rl));
}
-#endif /* DEBUG */
+#endif /* CONFIG_DEBUG */
switch (mod) {
case 0:
destoffset = decode_rm00_address(rl);
END_OF_INSTR_NO_TRACE();
}
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
char *x86emu_fpu_op_dc_tab[] = {
"FADD\tQWORD PTR ", "FMUL\tQWORD PTR ", "FCOM\tQWORD PTR ",
"FCOMP\tQWORD PTR ",
"FADD\t", "FMUL\t", "FCOM\t", "FCOMP\t",
"FSUBR\t", "FSUB\t", "FDIVR\t", "FDIV\t",
};
-#endif /* DEBUG */
+#endif /* CONFIG_DEBUG */
/* opcode=0xdc */
void x86emuOp_esc_coprocess_dc(u8 X86EMU_UNUSED(op1))
END_OF_INSTR_NO_TRACE();
}
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
static char *x86emu_fpu_op_dd_tab[] = {
"FLD\tQWORD PTR ", "ESC_DD\t29,", "FST\tQWORD PTR ", "FSTP\tQWORD PTR ",
"ESC_DD\t2C,", "ESC_DD\t2D,", "ESC_DD\t2E,", "ESC_DD\t2F,",
};
-#endif /* DEBUG */
+#endif /* CONFIG_DEBUG */
/* opcode=0xdd */
void x86emuOp_esc_coprocess_dd(u8 X86EMU_UNUSED(op1))
END_OF_INSTR_NO_TRACE();
}
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
static char *x86emu_fpu_op_de_tab[] =
{
"FSUBRP\t", "FSUBP\t", "FDIVRP\t", "FDIVP\t",
};
-#endif /* DEBUG */
+#endif /* CONFIG_DEBUG */
/* opcode=0xde */
void x86emuOp_esc_coprocess_de(u8 X86EMU_UNUSED(op1))
END_OF_INSTR_NO_TRACE();
}
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
static char *x86emu_fpu_op_df_tab[] = {
/* mod == 00 */
"ESC_DF\t3C,", "ESC_DF\t3D,", "ESC_DF\t3E,", "ESC_DF\t3F,"
};
-#endif /* DEBUG */
+#endif /* CONFIG_DEBUG */
/* opcode=0xdf */
void x86emuOp_esc_coprocess_df(u8 X86EMU_UNUSED(op1))
#
#############################################################################
-.IMPORT .IGNORE: DEBUG
+.IMPORT .IGNORE: CONFIG_DEBUG
#----------------------------------------------------------------------------
# Define the lists of object files
OBJECTS = sys$O decode$O ops$O ops2$O prim_ops$O fpu$O debug$O
CFLAGS += -DSCITECH
-.IF $(DEBUG)
+.IF $(CONFIG_DEBUG)
CFLAGS += -DDEBUG
.ENDIF
LIBCLEAN = *.dll *.lib *.a
/* constant arrays to do several instructions in just one function */
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
static char *x86emu_GenOpName[8] = {
"ADD", "OR", "ADC", "SBB", "AND", "SUB", "XOR", "CMP"};
#endif
sar_long,
};
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
static char *opF6_names[8] =
{ "TEST\t", "", "NOT\t", "NEG\t", "MUL\t", "IMUL\t", "DIV\t", "IDIV\t" };
*/
START_OF_INSTR();
FETCH_DECODE_MODRM(mod, rh, rl);
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
if (DEBUG_DECODE()) {
/* XXX DECODE_PRINTF may be changed to something more
general, so that it is important to leave the strings
*/
START_OF_INSTR();
FETCH_DECODE_MODRM(mod, rh, rl);
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
if (DEBUG_DECODE()) {
/* XXX DECODE_PRINTF may be changed to something more
general, so that it is important to leave the strings
*/
START_OF_INSTR();
FETCH_DECODE_MODRM(mod, rh, rl);
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
if (DEBUG_DECODE()) {
/* XXX DECODE_PRINTF may be changed to something more
general, so that it is important to leave the strings
*/
START_OF_INSTR();
FETCH_DECODE_MODRM(mod, rh, rl);
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
if (DEBUG_DECODE()) {
/* XXX DECODE_PRINTF may be changed to something more
general, so that it is important to leave the strings
*/
START_OF_INSTR();
FETCH_DECODE_MODRM(mod, rh, rl);
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
if (DEBUG_DECODE()) {
/* XXX DECODE_PRINTF may be changed to something more
general, so that it is important to leave the strings
*/
START_OF_INSTR();
FETCH_DECODE_MODRM(mod, rh, rl);
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
if (DEBUG_DECODE()) {
/* XXX DECODE_PRINTF may be changed to something more
general, so that it is important to leave the strings
*/
START_OF_INSTR();
FETCH_DECODE_MODRM(mod, rh, rl);
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
if (DEBUG_DECODE()) {
/* XXX DECODE_PRINTF may be changed to something more
general, so that it is important to leave the strings
*/
START_OF_INSTR();
FETCH_DECODE_MODRM(mod, rh, rl);
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
if (DEBUG_DECODE()) {
/* XXX DECODE_PRINTF may be changed to something more
general, so that it is important to leave the strings
*/
START_OF_INSTR();
FETCH_DECODE_MODRM(mod, rh, rl);
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
if (DEBUG_DECODE()) {
/* XXX DECODE_PRINTF may be changed to something more
general, so that it is important to leave the strings
*/
START_OF_INSTR();
FETCH_DECODE_MODRM(mod, rh, rl);
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
if (DEBUG_DECODE()) {
/* XXX DECODE_PRINTF may be changed to something more
general, so that it is important to leave the strings
/* Yet another special case instruction. */
START_OF_INSTR();
FETCH_DECODE_MODRM(mod, rh, rl);
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
if (DEBUG_DECODE()) {
/* XXX DECODE_PRINTF may be changed to something more
general, so that it is important to leave the strings
/* Yet another special case instruction. */
START_OF_INSTR();
FETCH_DECODE_MODRM(mod, rh, rl);
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
if (DEBUG_DECODE()) {
/* XXX DECODE_PRINTF may be changed to something more
general, so that it is important to leave the strings
#define CHECK_MEM_ACCESS_F 0x4 /*using regular linear pointer */
#define CHECK_DATA_ACCESS_F 0x8 /*using segment:offset*/
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
# define CHECK_IP_FETCH() (M.x86.check & CHECK_IP_FETCH_F)
# define CHECK_SP_ACCESS() (M.x86.check & CHECK_SP_ACCESS_F)
# define CHECK_MEM_ACCESS() (M.x86.check & CHECK_MEM_ACCESS_F)
# define CHECK_DATA_ACCESS()
#endif
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
# define DEBUG_INSTRUMENT() (M.x86.debug & DEBUG_INSTRUMENT_F)
# define DEBUG_DECODE() (M.x86.debug & DEBUG_DECODE_F)
# define DEBUG_TRACE() (M.x86.debug & DEBUG_TRACE_F)
# define DEBUG_DECODE_NOPRINT() 0
#endif
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
# define DECODE_PRINTF(x) if (DEBUG_DECODE()) \
x86emu_decode_printf(x)
# define SAVE_IP_CS(x,y)
#endif
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
#define TRACE_REGS() \
if (DEBUG_DISASSEMBLE()) { \
x86emu_just_disassemble(); \
# define TRACE_REGS()
#endif
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
# define SINGLE_STEP() if (DEBUG_STEP()) x86emu_single_step()
#else
# define SINGLE_STEP()
TRACE_REGS(); \
SINGLE_STEP()
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
# define START_OF_INSTR()
# define END_OF_INSTR() EndOfTheInstructionProcedure: x86emu_end_instr();
# define END_OF_INSTR_NO_TRACE() x86emu_end_instr();
# define END_OF_INSTR_NO_TRACE()
#endif
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
# define CALL_TRACE(u,v,w,x,s) \
if (DEBUG_TRACECALLREGS()) \
x86emu_dump_regs(); \
# define RETURN_TRACE(n,u,v)
#endif
-#ifdef DEBUG
+#ifdef CONFIG_DEBUG
#define DB(x) x
#else
#define DB(x)
projects / coreboot.git / commitdiff