##
## The Serial Console
##
-default CONFIG_USE_PRINTK_IN_CAR=0
+default CONFIG_USE_PRINTK_IN_CAR=1
# To Enable the Serial Console
default CONFIG_CONSOLE_SERIAL8250=1
#if CONFIG_USE_INIT == 0
#include "lib/memcpy.c"
- #if CONFIG_USE_PRINTK_IN_CAR == 1
- #include "lib/uart8250.c"
- #include "console/vtxprintf.c"
- #include "arch/i386/lib/printk_init.c"
- #endif
#endif
#include "arch/i386/lib/console.c"
#include "option_table.h"
#include "pc80/mc146818rtc_early.c"
+
#if 0
static void post_code(uint8_t value) {
#if 1
#if CONFIG_USE_INIT == 0
#include "lib/memcpy.c"
- #if CONFIG_USE_PRINTK_IN_CAR == 1
- #include "lib/uart8250.c"
- #include "console/vtxprintf.c"
- #include "arch/i386/lib/printk_init.c"
- #endif
#endif
#include "northbridge/amd/amdk8/debug.c"
#include "cpu/amd/mtrr/amd_earlymtrr.c"
uses CONFIG_PCI_64BIT_PREF_MEM
uses CONFIG_LB_MEM_TOPK
-
+uses CONFIG_USE_PRINTK_IN_CAR
###
### Build options
default DCACHE_RAM_BASE=0xcc000
default DCACHE_RAM_SIZE=0x04000
default DCACHE_RAM_GLOBAL_VAR_SIZE=0x01000
-default CONFIG_USE_INIT=0
+default CONFIG_USE_INIT=0\r
##
## Build code to setup a generic IOAPIC
##
## The Serial Console
##
+default CONFIG_USE_PRINTK_IN_CAR=1
# To Enable the Serial Console
default CONFIG_CONSOLE_SERIAL8250=1
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_COMPRESSED_PAYLOAD_NRV2B
uses CONFIG_PRECOMPRESSED_PAYLOAD
+uses CONFIG_USE_PRINTK_IN_CAR\r
## ROM_SIZE is the size of boot ROM that this board will use.
#512K bytes
default APIC_ID_OFFSET=0x10
default LIFT_BSP_APIC_ID=0
-
##
## Build code to setup a generic IOAPIC
##
##
## The Serial Console
##
-
+default CONFIG_USE_PRINTK_IN_CAR=1
+\r
# To Enable the Serial Console
default CONFIG_CONSOLE_SERIAL8250=1
default DCACHE_RAM_GLOBAL_VAR_SIZE=0x01000
default CONFIG_USE_INIT=0
-default CONFIG_AP_CODE_IN_CAR=0
+default CONFIG_AP_CODE_IN_CAR=1
default MEM_TRAIN_SEQ=1
default WAIT_BEFORE_CPUS_INIT=1
##
## The Serial Console
##
-default CONFIG_USE_PRINTK_IN_CAR=0
+default CONFIG_USE_PRINTK_IN_CAR=1
# To Enable the Serial Console
default CONFIG_CONSOLE_SERIAL8250=1
romimage "normal"
option USE_FAILOVER_IMAGE=0
option USE_FALLBACK_IMAGE=0
- option ROM_IMAGE_SIZE=0x18000
+ option ROM_IMAGE_SIZE=0x20000
option COREBOOT_EXTRA_VERSION=".0-normal"
payload __PAYLOAD__
end
romimage "fallback"
option USE_FAILOVER_IMAGE=0
option USE_FALLBACK_IMAGE=1
- option ROM_IMAGE_SIZE=0x18000
+ option ROM_IMAGE_SIZE=0x20000
option COREBOOT_EXTRA_VERSION=".0-fallback"
payload __PAYLOAD__
end