2 * This file is part of the coreboot project.
4 * Copyright (C) 2007 Advanced Micro Devices, Inc.
6 * This program is free software; you can redistribute it and/or modify
7 * it under the terms of the GNU General Public License version 2 as
8 * published by the Free Software Foundation.
10 * This program is distributed in the hope that it will be useful,
11 * but WITHOUT ANY WARRANTY; without even the implied warranty of
12 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
13 * GNU General Public License for more details.
15 * You should have received a copy of the GNU General Public License
16 * along with this program; if not, write to the Free Software
17 * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
23 #include <device/pci_def.h>
25 #include <device/pnp_def.h>
26 #include <arch/romcc_io.h>
28 #include <console/console.h>
30 #include "cpu/x86/bist.h"
31 #include "cpu/x86/msr.h"
32 #include <cpu/amd/lxdef.h>
33 #include <cpu/amd/geode_post_code.h>
34 #include "southbridge/amd/cs5536/cs5536.h"
36 #define SERIAL_DEV PNP_DEV(0x2e, W83627HF_SP1)
38 /* The ALIX.2D has no SMBus; the setup is hard-wired. */
39 static void cs5536_enable_smbus(void) { }
41 #include "southbridge/amd/cs5536/cs5536_early_setup.c"
43 /* The part is a Hynix hy5du121622ctp-d43.
45 * HY 5D U 12 16 2 2 C <blank> T <blank> P D43
48 * VDD 2.5 VDDQ 2.5 (U)
49 * 512M 8K REFRESH (12)
54 * Normal Power Consumption (<blank> )
56 * Single Die (<blank>)
61 static const u8 spdbytes[] = {
62 [SPD_ACCEPTABLE_CAS_LATENCIES] = 0x10,
63 [SPD_BANK_DENSITY] = 0x40,
64 [SPD_DEVICE_ATTRIBUTES_GENERAL] = 0xff,
65 [SPD_MEMORY_TYPE] = 7,
66 [SPD_MIN_CYCLE_TIME_AT_CAS_MAX] = 10, /* A guess for the tRAC value */
67 [SPD_MODULE_ATTRIBUTES] = 0xff, /* FIXME later when we figure out. */
68 [SPD_NUM_BANKS_PER_SDRAM] = 4,
69 [SPD_PRIMARY_SDRAM_WIDTH] = 8,
70 [SPD_NUM_DIMM_BANKS] = 1, /* ALIX1.C is 1 bank. */
71 [SPD_NUM_COLUMNS] = 0xa,
74 [SPD_SDRAM_CYCLE_TIME_2ND] = 60,
75 [SPD_SDRAM_CYCLE_TIME_3RD] = 75,
83 static u8 spd_read_byte(u8 device, u8 address)
85 print_debug("spd_read_byte dev ");
86 print_debug_hex8(device);
88 if (device != DIMM0) {
89 print_debug(" returns 0xff\n");
93 print_debug(" addr ");
94 print_debug_hex8(address);
95 print_debug(" returns ");
96 print_debug_hex8(spdbytes[address]);
99 return spdbytes[address];
102 #define ManualConf 0 /* Do automatic strapped PLL config */
103 #define PLLMSRhi 0x00001490 /* Manual settings for the PLL */
104 #define PLLMSRlo 0x02000030
106 #include "northbridge/amd/lx/raminit.h"
107 #include "northbridge/amd/lx/pll_reset.c"
108 #include "northbridge/amd/lx/raminit.c"
109 #include "lib/generic_sdram.c"
110 #include "cpu/amd/model_lx/cpureginit.c"
111 #include "cpu/amd/model_lx/syspreinit.c"
112 #include "cpu/amd/model_lx/msrinit.c"
114 /** Early mainboard specific GPIO setup. */
115 static void mb_gpio_init(void)
118 * Enable LEDs GPIO outputs to light up the leds
119 * This is how the original tinyBIOS sets them after boot.
120 * Info: GPIO_IO_BASE, 0x6100, is only valid before PCI init, so it
121 * may be used here, but not after PCI Init.
122 * Note: Prior to a certain release, Linux used a hardwired 0x6100 in the
123 * leds-alix2.c driver. Coreboot dynamically assigns this space,
124 * so the driver does not work anymore.
125 * Good workaround: use the newer driver
126 * Ugly workaround: $ wrmsr 0x5140000C 0xf00100006100
127 * This resets the GPIO I/O space to 0x6100.
128 * This may break other things, though.
130 outl(1 << 6, GPIO_IO_BASE + GPIOL_OUTPUT_ENABLE);
131 outl(1 << 9, GPIO_IO_BASE + GPIOH_OUTPUT_ENABLE);
132 outl(1 << 11, GPIO_IO_BASE + GPIOH_OUTPUT_ENABLE);
134 /* outl(1 << 6, GPIO_IO_BASE + GPIOL_OUTPUT_VALUE); */ /* Led 1 enabled */
135 outl(1 << 9, GPIO_IO_BASE + GPIOH_OUTPUT_VALUE); /* Led 2 disabled */
136 outl(1 << 11, GPIO_IO_BASE + GPIOH_OUTPUT_VALUE); /* Led 3 disabled */
139 void main(unsigned long bist)
141 static const struct mem_controller memctrl[] = {
142 {.channel0 = {DIMM0}},
150 cs5536_early_setup();
152 /* NOTE: Must do this AFTER cs5536_early_setup()!
153 * It is counting on some early MSR setup for the CS5536.
155 cs5536_setup_onchipuart(1);
160 /* Halt if there was a built in self test failure */
161 report_bist_failure(bist);
163 pll_reset(ManualConf);
165 cpuRegInit(0, DIMM0, DIMM1, DRAM_TERMINATED);
167 sdram_initialize(1, memctrl);
169 /* Switch from Cache as RAM to real RAM.
171 * There are two ways we could think about this.
173 * 1. If we are using the romstage.inc ROMCC way, the stack is
174 * going to be re-setup in the code following this code. Just
175 * wbinvd the stack to clear the cache tags. We don't care
176 * where the stack used to be.
178 * 2. This file is built as a normal .c -> .o and linked in
179 * etc. The stack might be used to return etc. That means we
180 * care about what is in the stack. If we are smart we set
181 * the CAR stack to the same location as the rest of
182 * coreboot. If that is the case we can just do a wbinvd.
183 * The stack will be written into real RAM that is now setup
184 * and we continue like nothing happened. If the stack is
185 * located somewhere other than where LB would like it, you
186 * need to write some code to do a copy from cache to RAM
188 * We use method 1 on Norwich and on this board too.
191 print_err("POST 02\n");
193 print_err("Past wbinvd\n");
195 /* We are finding the return does not work on this board. Explicitly
196 * call the label that is after the call to us. This is gross, but
197 * sometimes at this level it is the only way out.
199 void done_cache_as_ram_main(void);
200 done_cache_as_ram_main();