ITE IT8661F changes to match the common code structure.

 - it8661f_enable_serial() is now in the usual format, using pnp_* functions.

 - Factor out pnp_enter_ext_func_mode()/pnp_exit_ext_func_mode().

 - Factor out it8661f_set_clkin() to set the CLKIN to 24/48MHz.

 - Factor out it8661f_enable_logical_devices(), might not be needed though.
   We leave it here until it's confirmed on hardware that it's not needed.

 - Move some #defines to it8661f.h.

 - Drop no longer used it8661f_sio_write().

Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6053 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1

diff --git a/src/superio/ite/it8661f/it8661f.h b/src/superio/ite/it8661f/it8661f.h
index ecc9473a6e086270f722b4016fe5c7e6223147bf..ee9bf10755fc295d5e9a2d3228e4b4f06540155a 100644 (file)
--- a/src/superio/ite/it8661f/it8661f.h
+++ b/src/superio/ite/it8661f/it8661f.h
@@ -23,6 +23,7 @@
 
 /* Datasheet: http://www.ite.com.tw/product_info/PC/Brief-IT8661_2.asp */
 
+/* Logical device numbers (LDNs). */
 #define IT8661F_FDC  0x00 /* Floppy */
 #define IT8661F_SP1  0x01 /* Com1 */
 #define IT8661F_SP2  0x02 /* Com2 */
@@ -30,4 +31,25 @@
 #define IT8661F_IR   0x04 /* IR */
 #define IT8661F_GPIO 0x05 /* GPIO & Alternate Function Configuration */
 
+/* Register and bit definitions. */
+#define IT8661F_REG_CC         0x02   /* Configure Control (write-only). */
+#define IT8661F_REG_LDE                0x23   /* PnP Logical Device Enable. */
+#define IT8661F_REG_SWSUSP     0x24   /* Software Suspend + Clock Select. */
+
+#define IT8661F_ISA_PNP_PORT   0x0279 /* Write-only. */
+
+#define IT8661F_CLKIN_24_MHZ   0
+#define IT8661F_CLKIN_48_MHZ   1
+
+/*
+ * Special values used for entering MB PnP mode. The first four bytes of
+ * each line determine the address port, the last four are data.
+ */
+static const u8 init_values[] = {
+       0x6a, 0xb5, 0xda, 0xed, /**/ 0xf6, 0xfb, 0x7d, 0xbe,
+       0xdf, 0x6f, 0x37, 0x1b, /**/ 0x0d, 0x86, 0xc3, 0x61,
+       0xb0, 0x58, 0x2c, 0x16, /**/ 0x8b, 0x45, 0xa2, 0xd1,
+       0xe8, 0x74, 0x3a, 0x9d, /**/ 0xce, 0xe7, 0x73, 0x39,
+};
+
 #endif

diff --git a/src/superio/ite/it8661f/it8661f_early_serial.c b/src/superio/ite/it8661f/it8661f_early_serial.c
index b3a344a7d8ec06bdec87792040962540625ae17f..c3edddcf4b40877f39b360b3f7beb2cc9d3b386a 100644 (file)
--- a/src/superio/ite/it8661f/it8661f_early_serial.c
+++ b/src/superio/ite/it8661f/it8661f_early_serial.c
@@ -21,74 +21,59 @@
 #include <arch/romcc_io.h>
 #include "it8661f.h"
 
-/* The base address is 0x3f0, 0x3bd, or 0x370, depending on config bytes. */
-#define SIO_BASE                   0x3f0
-#define SIO_INDEX                  SIO_BASE
-#define SIO_DATA                   (SIO_BASE + 1)
+/* Perform MB PnP setup to put the SIO chip at 0x3f0. */
+/* Base address 0x3f0: 0x86 0x80 0x55 0x55. */
+/* Base address 0x3bd: 0x86 0x80 0x55 0xaa. */
+/* Base address 0x370: 0x86 0x80 0xaa 0x55. */
+static void pnp_enter_ext_func_mode(device_t dev)
+{
+       int i;
+       u16 port = dev >> 8;
+
+       /* TODO: Don't hardcode Super I/O config port to 0x3f0. */
+       outb(0x86, IT8661F_ISA_PNP_PORT);
+       outb(0x80, IT8661F_ISA_PNP_PORT);
+       outb(0x55, IT8661F_ISA_PNP_PORT);
+       outb(0x55, IT8661F_ISA_PNP_PORT);
 
-/* Global configuration registers. */
-#define IT8661F_CONFIG_REG_CC      0x02   /* Configure Control (write-only). */
-#define IT8661F_CONFIG_REG_LDN     0x07   /* Logical Device Number. */
-#define IT8661F_CONFIG_REG_LDE     0x23   /* PnP Logical Device Enable. */
-#define IT8661F_CONFIG_REG_SWSUSP  0x24   /* Software Suspend + Clock Select. */
+       /* Sequentially write the 32 special values. */
+       for (i = 0; i < 32; i++)
+               outb(init_values[i], port);
+}
 
-#define IT8661F_CONFIGURATION_PORT 0x0279 /* Write-only. */
+static void pnp_exit_ext_func_mode(device_t dev)
+{
+       pnp_write_config(dev, IT8661F_REG_CC, (1 << 1));
+}
 
 /*
- * Special values used for entering MB PnP mode. The first four bytes of
- * each line determine the address port, the last four are data.
+ * The logical devices will only be involved in the ISA PnP sequence if their
+ * respective enable bits in IT8661F_REG_LDE are set.
+ *
+ * TODO: Find out if we actually need this (we use MB PnP mode).
+ *
+ * Bits: FDC (0), Com1 (1), Com2 (2), PP (3), IR (4). Bits 5-7 are reserved.
  */
-static const u8 init_values[] = {
-       0x6a, 0xb5, 0xda, 0xed, /**/ 0xf6, 0xfb, 0x7d, 0xbe,
-       0xdf, 0x6f, 0x37, 0x1b, /**/ 0x0d, 0x86, 0xc3, 0x61,
-       0xb0, 0x58, 0x2c, 0x16, /**/ 0x8b, 0x45, 0xa2, 0xd1,
-       0xe8, 0x74, 0x3a, 0x9d, /**/ 0xce, 0xe7, 0x73, 0x39,
-};
+static void it8661f_enable_logical_devices(device_t dev)
+{
+       pnp_enter_ext_func_mode(dev);
+       pnp_write_config(dev, IT8661F_REG_LDE, 0x1f);
+       pnp_exit_ext_func_mode(dev);
+}
 
-static void it8661f_sio_write(u8 ldn, u8 index, u8 value)
+static void it8661f_set_clkin(device_t dev, u8 clkin)
 {
-       outb(IT8661F_CONFIG_REG_LDN, SIO_BASE);
-       outb(ldn, SIO_DATA);
-       outb(index, SIO_BASE);
-       outb(value, SIO_DATA);
+       pnp_enter_ext_func_mode(dev);
+       pnp_write_config(dev, IT8661F_REG_SWSUSP, (clkin << 1));
+       pnp_exit_ext_func_mode(dev);
 }
 
-/* Enable the serial port(s). */
 static void it8661f_enable_serial(device_t dev, u16 iobase)
 {
-       int i;
-
-       /* (1) Enter the configuration state (MB PnP mode). */
-
-       /* Perform MB PnP setup to put the SIO chip at 0x3f0. */
-       /* Base address 0x3f0: 0x86 0x80 0x55 0x55. */
-       /* Base address 0x3bd: 0x86 0x80 0x55 0xaa. */
-       /* Base address 0x370: 0x86 0x80 0xaa 0x55. */
-       outb(0x86, IT8661F_CONFIGURATION_PORT);
-       outb(0x80, IT8661F_CONFIGURATION_PORT);
-       outb(0x55, IT8661F_CONFIGURATION_PORT);
-       outb(0x55, IT8661F_CONFIGURATION_PORT);
-
-       /* Sequentially write the 32 special values. */
-       for (i = 0; i < 32; i++)
-               outb(init_values[i], SIO_BASE);
-
-       /* (2) Modify the data of configuration registers. */
-
-       /*
-        * Allow all devices to be enabled. Bits: FDC (0), Com1 (1), Com2 (2),
-        * PP (3), IR (4). Bits 5-7 are reserved.
-        */
-       it8661f_sio_write(0x00, IT8661F_CONFIG_REG_LDE, 0x1f);
-
-       /* Enable serial port(s). */
-       it8661f_sio_write(IT8661F_SP1, 0x30, 0x1); /* Serial port 1 */
-       it8661f_sio_write(IT8661F_SP2, 0x30, 0x1); /* Serial port 2 */
-
-       /* Select 24MHz CLKIN (clear bit 1) and clear software suspend mode
-          (clear bit 0). */
-       it8661f_sio_write(0x00, IT8661F_CONFIG_REG_SWSUSP, 0x00);
-
-       /* (3) Exit the configuration state (MB PnP mode). */
-       it8661f_sio_write(0x00, IT8661F_CONFIG_REG_CC, 0x02);
+       pnp_enter_ext_func_mode(dev);
+       pnp_set_logical_device(dev);
+       pnp_set_enable(dev, 0);
+       pnp_set_iobase(dev, PNP_IDX_IO0, iobase);
+       pnp_set_enable(dev, 1);
+       pnp_exit_ext_func_mode(dev);
 }

diff --git a/src/superio/ite/it8661f/superio.c b/src/superio/ite/it8661f/superio.c
index e367ab855560b709a9f27527bdf352024026cf91..f4b729a73a4879f517c3e35394c9392047d299ad 100644 (file)
--- a/src/superio/ite/it8661f/superio.c
+++ b/src/superio/ite/it8661f/superio.c
@@ -25,10 +25,12 @@
 #include "chip.h"
 #include "it8661f.h"
 
+/* TODO: Add pnp_enter_ext_func_mode() etc. and wrap functions. */
+
 static void init(device_t dev)
 {
        struct superio_ite_it8661f_config *conf = dev->chip_info;
-       struct resource *res0, *res1;
+       struct resource *res0;
 
        if (!dev->enabled)
                return;