re-indent, so files conform to coding guidelines.

Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Change-Id: If840164fa0e2b6349ba920edf06386ba1fe08aab
Reviewed-on: http://review.coreboot.org/8
Tested-by: build bot (Jenkins)
Reviewed-by: Cristian Măgherușan-Stanciu <cristi.magherusan@gmail.com>

diff --git a/src/mainboard/asrock/e350m1/romstage.c b/src/mainboard/asrock/e350m1/romstage.c
index 4b45caf6e933f4ff47908c6deb9b803ad515a910..7d25ec1d384d6017eeb1e512a5492b527307516f 100644 (file)
--- a/src/mainboard/asrock/e350m1/romstage.c
+++ b/src/mainboard/asrock/e350m1/romstage.c
@@ -44,110 +44,110 @@ void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx);
 
 void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
 {
-  u32 val;
-  u8 reg8;
-
-  // all cores: allow caching of flash chip code and data
-  // (there are no cache-as-ram reliability concerns with family 14h)
-  __writemsr (0x20c, (0x0100000000ull - CONFIG_ROM_SIZE) | 5);
-  __writemsr (0x20d, (0x1000000000ull - CONFIG_ROM_SIZE) | 0x800);
-
-  // all cores: set pstate 0 (1600 MHz) early to save a few ms of boot time
-  __writemsr (0xc0010062, 0);
-
-  // early enable of PrefetchEnSPIFromHost
-  if (boot_cpu())
-    {
-    __outdword (0xcf8, 0x8000a3b8);
-    __outdword (0xcfc, __indword (0xcfc) | 1 << 24);
-    }
-
-  // early enable of SPI 33 MHz fast mode read
-  if (boot_cpu())
-    {
-    volatile u32 *spiBase = (void *) 0xa0000000;
-    u32 save;
-    __outdword (0xcf8, 0x8000a3a0);
-    save = __indword (0xcfc);
-    __outdword (0xcfc, (u32) spiBase | 2); // set temp MMIO base
-    spiBase [3] = (spiBase [3] & ~(3 << 14)) | (1 << 14);
-    spiBase [0] |= 1 << 18; // fast read enable
-    __outdword (0xcfc, save); // clear temp base
-    }
-
-  if (!cpu_init_detectedx && boot_cpu()) {
-    post_code(0x30);
-    sb_poweron_init();
-
-    post_code(0x31);
-    w83627hf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
-    console_init();
-  }
+       u32 val;
+       u8 reg8;
+
+       // all cores: allow caching of flash chip code and data
+       // (there are no cache-as-ram reliability concerns with family 14h)
+       __writemsr(0x20c, (0x0100000000ull - CONFIG_ROM_SIZE) | 5);
+       __writemsr(0x20d, (0x1000000000ull - CONFIG_ROM_SIZE) | 0x800);
+
+       // all cores: set pstate 0 (1600 MHz) early to save a few ms of boot time
+       __writemsr(0xc0010062, 0);
+
+       // early enable of PrefetchEnSPIFromHost
+       if (boot_cpu()) {
+               __outdword(0xcf8, 0x8000a3b8);
+               __outdword(0xcfc, __indword(0xcfc) | 1 << 24);
+       }
+       // early enable of SPI 33 MHz fast mode read
+       if (boot_cpu()) {
+               volatile u32 *spiBase = (void *)0xa0000000;
+               u32 save;
+               __outdword(0xcf8, 0x8000a3a0);
+               save = __indword(0xcfc);
+               __outdword(0xcfc, (u32) spiBase | 2);   // set temp MMIO base
+               spiBase[3] = (spiBase[3] & ~(3 << 14)) | (1 << 14);
+               spiBase[0] |= 1 << 18;  // fast read enable
+               __outdword(0xcfc, save);        // clear temp base
+       }
+
+       if (!cpu_init_detectedx && boot_cpu()) {
+               post_code(0x30);
+               sb_poweron_init();
+
+               post_code(0x31);
+               w83627hf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
+               console_init();
+       }
        //reg8 = pmio_read(0x24);
-  outb(0x24, 0xCD6);
-  reg8 = inb(0xCD7);
+       outb(0x24, 0xCD6);
+       reg8 = inb(0xCD7);
        reg8 |= 1;
        reg8 &= ~(1 << 1);
        //pmio_write(0x24, reg8);
        outb(0x24, 0xCD6);
        outb(reg8, 0xCD7);
 
-       *(volatile u32 *)(0xFED80000+0xE00+0x40) &= ~((1 << 0) | (1 << 2)); /* 48Mhz */
-       *(volatile u32 *)(0xFED80000+0xE00+0x40) |= 1 << 1; /* 48Mhz */
-
-  /* Halt if there was a built in self test failure */
-  post_code(0x34);
-  report_bist_failure(bist);
-
-  // Load MPB
-  val = cpuid_eax(1);
-  printk(BIOS_DEBUG, "BSP Family_Model: %08x \n", val);
-  printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx \n", cpu_init_detectedx);
-
-  post_code(0x35);
-  val = agesawrapper_amdinitmmio();
-
-  post_code(0x37);
-  val = agesawrapper_amdinitreset();
-  if(val) {
-    printk(BIOS_DEBUG, "agesawrapper_amdinitreset failed: %x \n", val);
-  }
-
-  post_code(0x38);
-  printk(BIOS_DEBUG, "Got past sb800_early_setup\n");
-
-  post_code(0x39);
-  val = agesawrapper_amdinitearly ();
-  if(val) {
-    printk(BIOS_DEBUG, "agesawrapper_amdinitearly failed: %x \n", val);
-  }
-  printk(BIOS_DEBUG, "Got past agesawrapper_amdinitearly\n");
-
-  post_code(0x40);
-  val = agesawrapper_amdinitpost ();
-  if(val) {
-    printk(BIOS_DEBUG, "agesawrapper_amdinitpost failed: %x \n", val);
-  }
-  printk(BIOS_DEBUG, "Got past agesawrapper_amdinitpost\n");
-
-  post_code(0x41);
-  val = agesawrapper_amdinitenv ();
-  if(val) {
-    printk(BIOS_DEBUG, "agesawrapper_amdinitenv failed: %x \n", val);
-  }
-  printk(BIOS_DEBUG, "Got past agesawrapper_amdinitenv\n");
-
-  /* Initialize i8259 pic */
-  post_code(0x41);
-  setup_i8259 ();
-
-  /* Initialize i8254 timers */
-  post_code(0x42);
-  setup_i8254 ();
-
-  post_code(0x50);
-  copy_and_run(0);
-
-  post_code(0x54);  // Should never see this post code.
+       *(volatile u32 *)(0xFED80000 + 0xE00 + 0x40) &= ~((1 << 0) | (1 << 2)); /* 48Mhz */
+       *(volatile u32 *)(0xFED80000 + 0xE00 + 0x40) |= 1 << 1; /* 48Mhz */
+
+       /* Halt if there was a built in self test failure */
+       post_code(0x34);
+       report_bist_failure(bist);
+
+       // Load MPB
+       val = cpuid_eax(1);
+       printk(BIOS_DEBUG, "BSP Family_Model: %08x \n", val);
+       printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx \n", cpu_init_detectedx);
+
+       post_code(0x35);
+       val = agesawrapper_amdinitmmio();
+
+       post_code(0x37);
+       val = agesawrapper_amdinitreset();
+       if (val) {
+               printk(BIOS_DEBUG, "agesawrapper_amdinitreset failed: %x \n",
+                      val);
+       }
+
+       post_code(0x38);
+       printk(BIOS_DEBUG, "Got past sb800_early_setup\n");
+
+       post_code(0x39);
+       val = agesawrapper_amdinitearly();
+       if (val) {
+               printk(BIOS_DEBUG, "agesawrapper_amdinitearly failed: %x \n",
+                      val);
+       }
+       printk(BIOS_DEBUG, "Got past agesawrapper_amdinitearly\n");
+
+       post_code(0x40);
+       val = agesawrapper_amdinitpost();
+       if (val) {
+               printk(BIOS_DEBUG, "agesawrapper_amdinitpost failed: %x \n",
+                      val);
+       }
+       printk(BIOS_DEBUG, "Got past agesawrapper_amdinitpost\n");
+
+       post_code(0x41);
+       val = agesawrapper_amdinitenv();
+       if (val) {
+               printk(BIOS_DEBUG, "agesawrapper_amdinitenv failed: %x \n",
+                      val);
+       }
+       printk(BIOS_DEBUG, "Got past agesawrapper_amdinitenv\n");
+
+       /* Initialize i8259 pic */
+       post_code(0x41);
+       setup_i8259();
+
+       /* Initialize i8254 timers */
+       post_code(0x42);
+       setup_i8254();
+
+       post_code(0x50);
+       copy_and_run(0);
+
+       post_code(0x54);        // Should never see this post code.
 }
-

diff --git a/src/southbridge/amd/cimx_wrapper/sb800/bootblock.c b/src/southbridge/amd/cimx_wrapper/sb800/bootblock.c
index 629685d689b99bbf6dd1a3d81252d3d6f580c6a4..9d8a349c6ea960d9cb886aa6e760831ef9da01c6 100644 (file)
--- a/src/southbridge/amd/cimx_wrapper/sb800/bootblock.c
+++ b/src/southbridge/amd/cimx_wrapper/sb800/bootblock.c
@@ -17,48 +17,47 @@
  * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
  */
 
-
 #include <arch/io.h>
 #include <arch/romcc_io.h>
 
 static void sb800_enable_rom(void)
 {
-  u32 word;
-  u32 dword;
-  device_t dev;
+       u32 word;
+       u32 dword;
+       device_t dev;
 
-  dev = PCI_DEV(0, 0x14, 0x03);
-  /* SB800 LPC Bridge 0:20:3:44h.
-   * BIT6: Port Enable for serial port 0x3f8-0x3ff
-   * BIT29: Port Enable for KBC port 0x60 and 0x64
-   * BIT30: Port Enable for ACPI Micro-Controller port 0x66 and 0x62
-   */
-  dword = pci_io_read_config32(dev, 0x44);
-  //dword |= (1<<6) | (1<<29) | (1<<30) ;
-  /* Turn on all of LPC IO Port decode enable */
-  dword = 0xffffffff;
-  pci_io_write_config32(dev, 0x44, dword);
+       dev = PCI_DEV(0, 0x14, 0x03);
+       /* SB800 LPC Bridge 0:20:3:44h.
+        * BIT6: Port Enable for serial port 0x3f8-0x3ff
+        * BIT29: Port Enable for KBC port 0x60 and 0x64
+        * BIT30: Port Enable for ACPI Micro-Controller port 0x66 and 0x62
+        */
+       dword = pci_io_read_config32(dev, 0x44);
+       //dword |= (1<<6) | (1<<29) | (1<<30) ;
+       /* Turn on all of LPC IO Port decode enable */
+       dword = 0xffffffff;
+       pci_io_write_config32(dev, 0x44, dword);
 
-  /* SB800 LPC Bridge 0:20:3:48h.
-   * BIT0: Port Enable for SuperIO 0x2E-0x2F 
-   * BIT1: Port Enable for SuperIO 0x4E-0x4F 
-   * BIT4: Port Enable for LPC ROM Address Arrage2 (0x68-0x6C)
-   * BIT6: Port Enable for RTC IO 0x70-0x73
-   * BIT21: Port Enable for Port 0x80
-   */
-  dword = pci_io_read_config32(dev, 0x48);
-  dword |= (1<<0) | (1<<1) | (1<<4) | (1<<6) | (1<<21) ;
-  pci_io_write_config32(dev, 0x48, dword);
+       /* SB800 LPC Bridge 0:20:3:48h.
+        * BIT0: Port Enable for SuperIO 0x2E-0x2F 
+        * BIT1: Port Enable for SuperIO 0x4E-0x4F 
+        * BIT4: Port Enable for LPC ROM Address Arrage2 (0x68-0x6C)
+        * BIT6: Port Enable for RTC IO 0x70-0x73
+        * BIT21: Port Enable for Port 0x80
+        */
+       dword = pci_io_read_config32(dev, 0x48);
+       dword |= (1 << 0) | (1 << 1) | (1 << 4) | (1 << 6) | (1 << 21);
+       pci_io_write_config32(dev, 0x48, dword);
 
-  /* Enable 4MB rom access at 0xFFE00000 - 0xFFFFFFFF */
-  /* Set the 4MB enable bits */
-  word = pci_io_read_config16(dev, 0x6c);
-  word = 0xFFC0; 
-  pci_io_write_config16(dev, 0x6c, word);
+       /* Enable 4MB rom access at 0xFFE00000 - 0xFFFFFFFF */
+       /* Set the 4MB enable bits */
+       word = pci_io_read_config16(dev, 0x6c);
+       word = 0xFFC0;
+       pci_io_write_config16(dev, 0x6c, word);
 }
 
 static void bootblock_southbridge_init(void)
 {
-  /* Setup the rom access for 2M */
-  sb800_enable_rom();
+       /* Setup the rom access for 2M */
+       sb800_enable_rom();
 }