config BOARD_LIPPERT_FRONTRUNNER
bool "Cool Frontrunner"
+config BOARD_LIPPERT_HURRICANE_LX
+ bool "Hurricane-LX"
config BOARD_LIPPERT_LITERUNNER_LX
bool "Cool LiteRunner-LX"
config BOARD_LIPPERT_ROADRUNNER_LX
endchoice
source "src/mainboard/lippert/frontrunner/Kconfig"
+source "src/mainboard/lippert/hurricane-lx/Kconfig"
source "src/mainboard/lippert/literunner-lx/Kconfig"
source "src/mainboard/lippert/roadrunner-lx/Kconfig"
source "src/mainboard/lippert/spacerunner-lx/Kconfig"
--- /dev/null
+if BOARD_LIPPERT_HURRICANE_LX
+
+config BOARD_SPECIFIC_OPTIONS # dummy
+ def_bool y
+ select ARCH_X86
+ select CPU_AMD_LX
+ select NORTHBRIDGE_AMD_LX
+ select SOUTHBRIDGE_AMD_CS5536
+ select SUPERIO_ITE_IT8712F
+ select HAVE_PIRQ_TABLE
+ select PIRQ_ROUTE
+ select UDELAY_TSC
+ select CACHE_AS_RAM
+ # Board is equipped with a 1 MB SPI flash, however, due to limitations
+ # of the IT8712F Super I/O, only the top 512 KB are directly mapped.
+ select BOARD_ROMSIZE_KB_512
+
+config MAINBOARD_DIR
+ string
+ default lippert/hurricane-lx
+
+config MAINBOARD_PART_NUMBER
+ string
+ default "Hurricane-LX"
+
+config IRQ_SLOT_COUNT
+ int
+ default 8
+
+config BOARD_OLD_REVISION
+ bool "Board is old pre-3.0 revision"
+ default n
+ help
+ Look on the bottom side for a number like 406-0001-30. The last 2
+ digits state the PCB revision (3.0 in this example). For 2.0 or older
+ boards choose Y, for 3.0 and newer say N.
+
+config ONBOARD_UARTS_RS485
+ bool "Switch on-board serial ports to RS485"
+ default n
+ help
+ If selected, both on-board serial ports will operate in RS485 mode
+ instead of RS232.
+
+endif # BOARD_LIPPERT_HURRICANE_LX
--- /dev/null
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2010 LiPPERT Embedded Computers GmbH
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+extern struct chip_operations mainboard_ops;
+
+struct mainboard_config {};
--- /dev/null
+chip northbridge/amd/lx
+ device pci_domain 0 on
+ device pci 1.0 on end # Northbridge
+ device pci 1.1 on end # Graphics
+ device pci 1.2 on end # AES
+ chip southbridge/amd/cs5536
+ # IRQ 12 and 1 unmasked, keyboard and mouse IRQs. OK
+ # SIRQ Mode = Active(Quiet) mode. Save power....
+ # Invert mask = IRQ 12 and 1 are active high. Keyboard and mouse,
+ # UARTs, etc IRQs. OK
+ register "lpc_serirq_enable" = "0x000012DA" # 00010010 11011010
+ register "lpc_serirq_polarity" = "0x0000ED25" # inverse of above
+ register "lpc_serirq_mode" = "1"
+ register "enable_gpio_int_route" = "0x0D0C0700"
+ register "enable_ide_nand_flash" = "0" # 0:ide mode, 1:flash
+ register "enable_USBP4_device" = "0" # 0:host, 1:device
+ register "enable_USBP4_overcurrent" = "0" # 0:off, xxxx:overcurrent setting CS5536 Data Book (pages 380-381)
+ register "com1_enable" = "0"
+ register "com1_address" = "0x3E8"
+ register "com1_irq" = "6"
+ register "com2_enable" = "0"
+ register "com2_address" = "0x2E8"
+ register "com2_irq" = "6"
+ register "unwanted_vpci[0]" = "0" # End of list has a zero
+ device pci 8.0 on end # Slot4
+ device pci 9.0 on end # Slot3
+ device pci a.0 on end # Slot2
+ device pci b.0 on end # Slot1
+ device pci c.0 on end # IT8888
+ device pci d.0 on end # Mini-PCI
+ device pci e.0 on end # Ethernet
+ device pci f.0 on # ISA Bridge
+ chip superio/ite/it8712f
+ device pnp 2e.0 on # Floppy
+ io 0x60 = 0x3f0
+ irq 0x70 = 6
+ drq 0x74 = 2
+ end
+ device pnp 2e.1 on # Com1
+ io 0x60 = 0x3f8
+ irq 0x70 = 4
+ end
+ device pnp 2e.2 on # Com2
+ io 0x60 = 0x2f8
+ irq 0x70 = 3
+ end
+ device pnp 2e.3 on # Parallel port
+ io 0x60 = 0x378
+ irq 0x70 = 7
+ end
+ device pnp 2e.4 on # EC
+ io 0x60 = 0x290 # EC
+ io 0x62 = 0x298 # PME
+ irq 0x70 = 9
+ end
+ device pnp 2e.5 on # PS/2 keyboard
+ io 0x60 = 0x60
+ io 0x62 = 0x64
+ irq 0x70 = 1
+ end
+ device pnp 2e.6 on # PS/2 mouse
+ irq 0x70 = 12
+ end
+ device pnp 2e.7 on # GPIO
+ io 0x62 = 0x1220 # Simple I/O
+ io 0x64 = 0x1228 # SPI
+ end
+ device pnp 2e.8 off # MIDI
+ io 0x60 = 0x300
+ irq 0x70 = 9
+ end
+ device pnp 2e.9 off # Game port
+ io 0x60 = 0x220
+ end
+ device pnp 2e.a off end # CIR
+ end
+ end
+ device pci f.2 on end # IDE
+ device pci f.3 on end # Audio
+ device pci f.4 on end # OHCI
+ device pci f.5 on end # EHCI
+ end
+ end
+ # APIC cluster is late CPU init.
+ device lapic_cluster 0 on
+ chip cpu/amd/model_lx
+ device lapic 0 on end
+ end
+ end
+end
--- /dev/null
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2010 LiPPERT Embedded Computers GmbH
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+/* Based on irq_tables.c from the SpaceRunner-LX mainboard. */
+
+#include <arch/pirq_routing.h>
+#include <console/console.h>
+#include <arch/io.h>
+#include <arch/pirq_routing.h>
+#include "../../../southbridge/amd/cs5536/cs5536.h"
+
+/* Platform IRQs */
+#define PIRQA 10
+#define PIRQB 11
+#define PIRQC 5
+#define PIRQD 15
+
+/* Map */
+#define M_PIRQA (1 << PIRQA) /* Bitmap of supported IRQs */
+#define M_PIRQB (1 << PIRQB) /* Bitmap of supported IRQs */
+#define M_PIRQC (1 << PIRQC) /* Bitmap of supported IRQs */
+#define M_PIRQD (1 << PIRQD) /* Bitmap of supported IRQs */
+
+/* Link */
+#define L_PIRQA 1 /* Means Slot INTx# Connects To Chipset INTA# */
+#define L_PIRQB 2 /* Means Slot INTx# Connects To Chipset INTB# */
+#define L_PIRQC 3 /* Means Slot INTx# Connects To Chipset INTC# */
+#define L_PIRQD 4 /* Means Slot INTx# Connects To Chipset INTD# */
+
+const struct irq_routing_table intel_irq_routing_table = {
+ PIRQ_SIGNATURE, /* u32 signature */
+ PIRQ_VERSION, /* u16 version */
+ 32 + 16 * CONFIG_IRQ_SLOT_COUNT,/* There can be total CONFIG_IRQ_SLOT_COUNT devices on the bus */
+ 0x00, /* Where the interrupt router lies (bus) */
+ (0x0F << 3) | 0x0, /* Where the interrupt router lies (dev) */
+ 0x00, /* IRQs devoted exclusively to PCI usage */
+ 0x100B, /* Vendor */
+ 0x002B, /* Device */
+ 0, /* Crap (miniport) */
+ {0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0}, /* u8 rfu[11] */
+ 0x36, /* u8 checksum, this has to set to some value that would give 0 after the sum of all bytes for this structure (including checksum) */
+ {
+ /* If you change the number of entries, change the CONFIG_IRQ_SLOT_COUNT above! */
+ /* bus, dev|fn, {link, bitmap}, {link, bitmap}, {link, bitmap}, {link, bitmap}, slot, rfu */
+ {0x00, (0x01 << 3) | 0x0, {{L_PIRQA, M_PIRQA}, {0x00, 0x00}, {0x00, 0x00}, {0x00, 0x00}}, 0x0, 0x0}, /* CPU */
+ {0x00, (0x0F << 3) | 0x0, {{L_PIRQA, M_PIRQA}, {L_PIRQB, M_PIRQB}, {L_PIRQC, M_PIRQC}, {L_PIRQD, M_PIRQD}}, 0x0, 0x0}, /* chipset */
+ {0x00, (0x0E << 3) | 0x0, {{L_PIRQC, M_PIRQC}, {0x00, 0x00}, {0x00, 0x00}, {0x00, 0x00}}, 0x0, 0x0}, /* ethernet */
+ {0x00, (0x0B << 3) | 0x0, {{L_PIRQA, M_PIRQA}, {L_PIRQB, M_PIRQB}, {L_PIRQC, M_PIRQC}, {L_PIRQD, M_PIRQD}}, 0x1, 0x0}, /* slot1 */
+ {0x00, (0x0A << 3) | 0x0, {{L_PIRQB, M_PIRQB}, {L_PIRQC, M_PIRQC}, {L_PIRQD, M_PIRQD}, {L_PIRQA, M_PIRQA}}, 0x2, 0x0}, /* slot2 */
+ {0x00, (0x09 << 3) | 0x0, {{L_PIRQC, M_PIRQC}, {L_PIRQD, M_PIRQD}, {L_PIRQA, M_PIRQA}, {L_PIRQB, M_PIRQB}}, 0x3, 0x0}, /* slot3 */
+ {0x00, (0x08 << 3) | 0x0, {{L_PIRQD, M_PIRQD}, {L_PIRQA, M_PIRQA}, {L_PIRQB, M_PIRQB}, {L_PIRQC, M_PIRQC}}, 0x4, 0x0}, /* slot4 */
+ {0x00, (0x0D << 3) | 0x0, {{L_PIRQB, M_PIRQB}, {L_PIRQA, M_PIRQA}, {0x00, 0x00}, {0x00, 0x00}}, 0x5, 0x0}, /* Mini-PCI */
+ }
+};
+
+unsigned long write_pirq_routing_table(unsigned long addr)
+{
+ return copy_pirq_routing_table(addr);
+}
--- /dev/null
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2010 LiPPERT Embedded Computers GmbH
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+/* Based on mainboard.c from the SpaceRunner-LX mainboard. */
+
+#include <stdlib.h>
+#include <stdint.h>
+#include <console/console.h>
+#include <device/device.h>
+#include <arch/io.h>
+#include <device/pci.h>
+#include <device/pci_ids.h>
+#include "chip.h"
+
+/* Bit1 switches Com1 to RS485, bit2 same for Com2. */
+#if CONFIG_ONBOARD_UARTS_RS485
+ #define SIO_GP1X_CONFIG 0x06
+#else
+ #define SIO_GP1X_CONFIG 0x00
+#endif
+
+static const u16 ec_init_table[] = { /* hi=data, lo=index */
+ 0x1900, /* Enable monitoring */
+ 0x0351, /* TMPIN1,2 diode mode, TMPIN3 off */
+ 0x805C, /* Unlock zero adjust */
+ 0x7056, 0x3C57, /* Zero adjust TMPIN1,2 */
+ 0x005C, /* Lock zero adjust */
+ 0xD014 /* Also set FAN_CTL polarity to Active High */
+};
+
+static void init(struct device *dev)
+{
+ unsigned int gpio_base, i;
+ printk(BIOS_DEBUG, "LiPPERT Hurricane-LX ENTER %s\n", __func__);
+
+ /* Init CS5536 GPIOs */
+ gpio_base = pci_read_config32(dev_find_device(PCI_VENDOR_ID_AMD,
+ PCI_DEVICE_ID_AMD_CS5536_ISA, 0), PCI_BASE_ADDRESS_1) - 1;
+
+ outl(0x00000040, gpio_base + 0x00); // GPIO6 value 1 - LAN_PD#
+ outl(0x00000040, gpio_base + 0x08); // GPIO6 open drain 1 - LAN_PD# (jumpered GPIO per default)
+ outl(0x00000040, gpio_base + 0x04); // GPIO6 output 1 - LAN_PD#
+ outl(0x00000400, gpio_base + 0x34); // GPIO10 in aux1 1 - THRM_ALRM#
+ outl(0x00000400, gpio_base + 0x20); // GPIO10 input 1 - THRM_ALRM#
+#if !CONFIG_BOARD_OLD_REVISION
+ outl(0x00000800, gpio_base + 0x94); // GPIO27 out aux2 1 - 32kHz
+ outl(0x00000800, gpio_base + 0x84); // GPIO27 output 1 - 32kHz
+#endif
+ outl(0x08000000, gpio_base + 0x98); // GPIO27 pull up 0 - 32kHz (new) / PM-LED (old)
+
+ /* Init Environment Controller. */
+ for (i = 0; i < ARRAY_SIZE(ec_init_table); i++) {
+ u16 val = ec_init_table[i];
+ outb((u8)val, 0x0295);
+ outb(val >> 8, 0x0296);
+ }
+
+ /* bit2 = RS485_EN2, bit1 = RS485_EN1 */
+ outb(SIO_GP1X_CONFIG, 0x1220); /* Simple-I/O GP17-10 */
+
+ printk(BIOS_DEBUG, "LiPPERT Hurricane-LX EXIT %s\n", __func__);
+}
+
+static void enable_dev(struct device *dev)
+{
+ dev->ops->init = init;
+}
+
+struct chip_operations mainboard_ops = {
+ CHIP_NAME("LiPPERT Hurricane-LX Mainboard")
+ .enable_dev = enable_dev,
+};
--- /dev/null
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2007 Advanced Micro Devices, Inc.
+ * Copyright (C) 2010 LiPPERT Embedded Computers GmbH
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+/* Based on romstage.c from the SpaceRunner-LX mainboard. */
+
+#include <stdlib.h>
+#include <stdint.h>
+#include <device/pci_def.h>
+#include <arch/io.h>
+#include <device/pnp_def.h>
+#include <arch/hlt.h>
+#include <console/console.h>
+#include "lib/ramtest.c"
+#include "cpu/x86/bist.h"
+#include "cpu/x86/msr.h"
+#include <cpu/amd/lxdef.h>
+#include <cpu/amd/geode_post_code.h>
+#include "southbridge/amd/cs5536/cs5536.h"
+
+#include "southbridge/amd/cs5536/cs5536_early_smbus.c"
+#include "southbridge/amd/cs5536/cs5536_early_setup.c"
+#include "superio/ite/it8712f/it8712f_early_serial.c"
+
+/* Bit0 enables Spread Spectrum. */
+#define SMC_CONFIG 0x01
+
+#define ManualConf 1 /* No automatic strapped PLL config */
+#define PLLMSRhi 0x0000049C /* Manual settings for the PLL */
+#define PLLMSRlo 0x00DE6001
+#define DIMM0 0xA0
+#define DIMM1 0xA2
+
+static inline int spd_read_byte(unsigned int device, unsigned int address)
+{
+ if (device != DIMM0)
+ return 0xFF; /* No DIMM1, don't even try. */
+
+ return smbus_read_byte(device, address);
+}
+
+#if !CONFIG_BOARD_OLD_REVISION
+/* Send config data to System Management Controller via SMB. */
+static int smc_send_config(unsigned char config_data)
+{
+ if (smbus_check_stop_condition(SMBUS_IO_BASE))
+ return 1;
+ if (smbus_start_condition(SMBUS_IO_BASE))
+ return 2;
+ if (smbus_send_slave_address(SMBUS_IO_BASE, 0x50)) // SMC address
+ return 3;
+ if (smbus_send_command(SMBUS_IO_BASE, 0x28)) // set config data
+ return 4;
+ if (smbus_send_command(SMBUS_IO_BASE, 0x01)) // data length
+ return 5;
+ if (smbus_send_command(SMBUS_IO_BASE, config_data))
+ return 6;
+ smbus_stop_condition(SMBUS_IO_BASE);
+ return 0;
+}
+#endif
+
+#include "northbridge/amd/lx/raminit.h"
+#include "northbridge/amd/lx/pll_reset.c"
+#include "northbridge/amd/lx/raminit.c"
+#include "lib/generic_sdram.c"
+#include "cpu/amd/model_lx/cpureginit.c"
+#include "cpu/amd/model_lx/syspreinit.c"
+#include "cpu/amd/model_lx/msrinit.c"
+
+static const u16 sio_init_table[] = { // hi=data, lo=index
+ 0x0707, // select LDN 7 (GPIO, SPI, watchdog, ...)
+ 0x042C, // disable ATXPG; VIN6 enabled, FAN4/5 disabled, VIN7,VIN3 enabled
+ 0x1423, // don't delay PoWeROK1/2
+ 0x9072, // watchdog triggers PWROK, counts seconds
+#if !CONFIG_USE_WATCHDOG_ON_BOOT
+ 0x0073, 0x0074, // disarm watchdog by changing 56 s timeout to 0
+#endif
+ 0xBF25, 0x172A, 0xF326, // select GPIO function for most pins
+ 0xBF27, 0xFF28, 0x2D29, // (GP36=FAN_CTL3 (PWM), GP23,22,16,15=SPI, GP13=PWROK1)
+ 0x66B8, 0x0CB9, // enable pullups on SPI, RS485_EN
+ 0x07C0, // enable Simple-I/O for GP12-10= RS485_EN2,1, WD_ACTIVE
+ 0x06C8, // config GP12,11 as output, GP10 as input
+ 0x2DF5, // map Hw Monitor Thermal Output to GP55
+#if CONFIG_BOARD_OLD_REVISION
+ 0x1F2A, 0xC072, // switch GP13 to GPIO, WDT output from PWROK to KRST
+#endif
+};
+
+/* Early mainboard specific GPIO setup. */
+static void mb_gpio_init(void)
+{
+ int i;
+
+ /* Init Super I/O WDT, GPIOs. Done early, WDT init may trigger reset! */
+ it8712f_enter_conf();
+ for (i = 0; i < ARRAY_SIZE(sio_init_table); i++) {
+ u16 val = sio_init_table[i];
+ outb((u8)val, SIO_INDEX);
+ outb(val >> 8, SIO_DATA);
+ }
+ it8712f_exit_conf();
+}
+
+void main(unsigned long bist)
+{
+ post_code(0x01);
+
+ static const struct mem_controller memctrl[] = {
+ {.channel0 = {(0xa << 3) | 0, (0xa << 3) | 1}}
+ };
+
+ SystemPreInit();
+ msr_init();
+
+ cs5536_early_setup();
+
+ /*
+ * Note: Must do this AFTER the early_setup! It is counting on some
+ * early MSR setup for CS5536.
+ */
+ it8712f_enable_serial(0, CONFIG_TTYS0_BASE); // Does not use its 1st parameter
+ mb_gpio_init();
+ uart_init();
+ console_init();
+
+ /* Halt if there was a built in self test failure */
+ report_bist_failure(bist);
+
+ pll_reset(ManualConf);
+
+ cpuRegInit(0, DIMM0, DIMM1, DRAM_TERMINATED);
+
+#if CONFIG_BOARD_OLD_REVISION
+ /*
+ * Old revision boards need a jumper shorting the power button to power
+ * on automatically. So we must disable the button's fail-safe function,
+ * or the board will shut down after 4 s.
+ */
+ outl(0, PMS_IO_BASE + PM_FSD); // Fail-Save Delay register
+#else
+ int err;
+ /* bit0 = Spread Spectrum */
+ if ((err = smc_send_config(SMC_CONFIG))) {
+ print_err("ERROR ");
+ print_err_char('0'+err);
+ print_err(" sending config data to SMC\n");
+ }
+#endif
+
+ sdram_initialize(1, memctrl);
+
+ /* Check memory. */
+ /* ram_check(0, 640 * 1024); */
+
+ /* Memory is setup. Return to cache_as_ram.inc and continue to boot. */
+ return;
+}
projects / coreboot.git / commitdiff