3 #include <device/pci_def.h>
5 #include <device/pnp_def.h>
6 #include <arch/romcc_io.h>
7 #include <cpu/x86/lapic.h>
8 #include <pc80/mc146818rtc.h>
9 #include <console/console.h>
13 #include <cpu/amd/model_fxx_rev.h>
15 #include "northbridge/amd/amdk8/incoherent_ht.c"
16 #include "southbridge/nvidia/ck804/ck804_early_smbus.h"
17 #include "northbridge/amd/amdk8/raminit.h"
18 #include "cpu/amd/model_fxx/apic_timer.c"
19 #include "lib/delay.c"
20 #include "cpu/x86/lapic/boot_cpu.c"
21 #include "northbridge/amd/amdk8/reset_test.c"
22 #include "northbridge/amd/amdk8/debug.c"
23 #include "superio/winbond/w83627hf/w83627hf_early_serial.c"
25 #include "cpu/x86/mtrr/earlymtrr.c"
26 #include "cpu/x86/bist.h"
28 #include "northbridge/amd/amdk8/setup_resource_map.c"
30 #define SERIAL_DEV PNP_DEV(0x2e, W83627HF_SP1)
32 static void memreset_setup(void)
36 static void memreset(int controllers, const struct mem_controller *ctrl)
40 static inline void activate_spd_rom(const struct mem_controller *ctrl)
45 static inline int spd_read_byte(unsigned device, unsigned address)
47 return smbus_read_byte(device, address);
50 #include "northbridge/amd/amdk8/raminit.c"
51 #include "northbridge/amd/amdk8/coherent_ht.c"
52 #include "lib/generic_sdram.c"
54 /* tyan does not want the default */
55 #include "resourcemap.c"
57 #include "cpu/amd/dualcore/dualcore.c"
59 #include "southbridge/nvidia/ck804/ck804_early_setup_ss.h"
60 #include "southbridge/nvidia/ck804/ck804_early_setup.c"
62 #include "cpu/amd/car/post_cache_as_ram.c"
64 #include "cpu/amd/model_fxx/init_cpus.c"
66 #include "northbridge/amd/amdk8/early_ht.c"
68 static void sio_setup(void)
74 byte = pci_read_config8(PCI_DEV(0, CK804_DEVN_BASE+1 , 0), 0x7b);
76 pci_write_config8(PCI_DEV(0, CK804_DEVN_BASE+1 , 0), 0x7b, byte);
78 /* LPC Positive Decode 0 */
79 dword = pci_read_config32(PCI_DEV(0, CK804_DEVN_BASE+1 , 0), 0xa0);
80 /* Serial 0, Serial 1 */
81 dword |= (1<<0) | (1<<1);
82 pci_write_config32(PCI_DEV(0, CK804_DEVN_BASE+1 , 0), 0xa0, dword);
85 /* s2891 has onboard LPC port 80 */
86 /*Hope I can enable port 80 here
87 It will decode port 80 to LPC, If you are using PCI post code you can not do this */
88 dword = pci_read_config32(PCI_DEV(0, CK804_DEVN_BASE+1 , 0), 0xa4);
90 pci_write_config32(PCI_DEV(0, CK804_DEVN_BASE+1 , 0), 0xa4, dword);
94 void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
96 static const uint16_t spd_addr [] = {
99 #if CONFIG_MAX_PHYSICAL_CPUS > 1
106 unsigned bsp_apicid = 0;
108 struct mem_controller ctrl[8];
111 if (!cpu_init_detectedx && boot_cpu()) {
112 /* Nothing special needs to be done to find bus 0 */
113 /* Allow the HT devices to be found */
115 enumerate_ht_chain();
121 bsp_apicid = init_cpus(cpu_init_detectedx);
126 w83627hf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
130 /* Halt if there was a built in self test failure */
131 report_bist_failure(bist);
133 setup_s2891_resource_map();
135 dump_pci_device(PCI_DEV(0, 0x18, 0));
136 dump_pci_device(PCI_DEV(0, 0x19, 0));
139 needs_reset = setup_coherent_ht_domain();
141 wait_all_core0_started();
142 #if CONFIG_LOGICAL_CPUS==1
143 // It is said that we should start core1 after all core0 launched
145 wait_all_other_cores_started(bsp_apicid);
148 needs_reset |= ht_setup_chains_x();
150 needs_reset |= ck804_early_setup_x();
153 printk(BIOS_INFO, "ht reset -\n");
157 allow_all_aps_stop(bsp_apicid);
160 //It's the time to set ctrl now;
161 fill_mem_ctrl(nodes, ctrl, spd_addr);
165 dump_spd_registers(&cpu[0]);
168 dump_smbus_registers();
172 sdram_initialize(nodes, ctrl);