2 * This file is part of the coreboot project.
4 * Copyright (C) 2007-2009 coresystems GmbH
6 * This program is free software; you can redistribute it and/or
7 * modify it under the terms of the GNU General Public License as
8 * published by the Free Software Foundation; version 2 of
11 * This program is distributed in the hope that it will be useful,
12 * but WITHOUT ANY WARRANTY; without even the implied warranty of
13 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
14 * GNU General Public License for more details.
16 * You should have received a copy of the GNU General Public License
17 * along with this program; if not, write to the Free Software
18 * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
22 // __PRE_RAM__ means: use "unsigned" for device, not a struct.
24 /* Configuration of the i945 driver */
25 #define CHIPSET_I945GM 1
26 #define CHANNEL_XOR_RANDOMIZATION 1
27 // Rocky freezing temperature settings:
28 #define MAXIMUM_SUPPORTED_FREQUENCY 400
33 #include <arch/romcc_io.h>
34 #include <device/pci_def.h>
35 #include <device/pnp_def.h>
36 #include <cpu/x86/lapic.h>
38 #include "option_table.h"
39 #include "pc80/mc146818rtc_early.c"
41 #include <console/console.h>
42 #include "pc80/serial.c"
43 #include "console/console.c"
44 #include <cpu/x86/bist.h>
46 #if CONFIG_USBDEBUG_DIRECT
47 #define DBGP_DEFAULT 1
48 #include "southbridge/intel/i82801gx/i82801gx_usb_debug.c"
49 #include "pc80/usbdebug_direct_serial.c"
52 #include "lib/ramtest.c"
53 #include "southbridge/intel/i82801gx/i82801gx_early_smbus.c"
55 #include "northbridge/intel/i945/udelay.c"
57 #include "southbridge/intel/i82801gx/i82801gx.h"
58 static void setup_ich7_gpios(void)
60 printk(BIOS_DEBUG, " GPIOS...");
61 /* General Registers */
62 outl(0xbfc0f7c0, DEFAULT_GPIOBASE + 0x00); /* GPIO_USE_SEL */
63 outl(0x70a87d83, DEFAULT_GPIOBASE + 0x04); /* GP_IO_SEL */
64 outl(0x7dc07f83, DEFAULT_GPIOBASE + 0x0c); /* GP_LVL */
65 /* Output Control Registers */
66 outl(0x00000000, DEFAULT_GPIOBASE + 0x18); /* GPO_BLINK */
67 /* Input Control Registers */
68 outl(0x00002180, DEFAULT_GPIOBASE + 0x2c); /* GPI_INV */
69 outl(0x000100e8, DEFAULT_GPIOBASE + 0x30); /* GPIO_USE_SEL2 */
70 outl(0x00000030, DEFAULT_GPIOBASE + 0x34); /* GP_IO_SEL2 */
71 outl(0x00010030, DEFAULT_GPIOBASE + 0x38); /* GP_LVL */
74 #include "northbridge/intel/i945/early_init.c"
76 static inline int spd_read_byte(unsigned device, unsigned address)
78 return smbus_read_byte(device, address);
81 #include "northbridge/intel/i945/raminit.h"
82 #include "northbridge/intel/i945/raminit.c"
83 #include "northbridge/intel/i945/errata.c"
84 #include "northbridge/intel/i945/debug.c"
86 static void ich7_enable_lpc(void)
89 pci_write_config8(PCI_DEV(0, 0x1f, 0), 0x64, 0xd0);
91 pci_write_config16(PCI_DEV(0, 0x1f, 0), 0x80, 0x0007);
93 pci_write_config16(PCI_DEV(0, 0x1f, 0), 0x82, 0x3f0f);
95 pci_write_config16(PCI_DEV(0, 0x1f, 0), 0x84, 0x02e1);
96 pci_write_config16(PCI_DEV(0, 0x1f, 0), 0x86, 0x001c);
98 pci_write_config32(PCI_DEV(0, 0x1f, 0), 0x88, 0x00fc0601);
100 pci_write_config32(PCI_DEV(0, 0x1f, 0), 0x8c, 0x00040069);
103 /* This box has two superios, so enabling serial becomes slightly excessive.
104 * We disable a lot of stuff to make sure that there are no conflicts between
105 * the two. Also set up the GPIOs from the beginning. This is the "no schematic
106 * but safe anyways" method.
108 static inline void pnp_enter_ext_func_mode(device_t dev)
110 unsigned int port = dev >> 8;
114 static void pnp_exit_ext_func_mode(device_t dev)
116 unsigned int port = dev >> 8;
120 static void pnp_write_register(device_t dev, int reg, int val)
122 unsigned int port = dev >> 8;
127 static void early_superio_config(void)
131 dev=PNP_DEV(0x2e, 0x00);
133 pnp_enter_ext_func_mode(dev);
134 pnp_write_register(dev, 0x01, 0x94); // Extended Parport modes
135 pnp_write_register(dev, 0x02, 0x88); // UART power on
136 pnp_write_register(dev, 0x03, 0x72); // Floppy
137 pnp_write_register(dev, 0x04, 0x01); // EPP + SPP
138 pnp_write_register(dev, 0x14, 0x03); // Floppy
139 pnp_write_register(dev, 0x20, (0x3f0 >> 2)); // Floppy
140 pnp_write_register(dev, 0x23, (0x378 >> 2)); // PP base
141 pnp_write_register(dev, 0x24, (0x3f8 >> 2)); // UART1 base
142 pnp_write_register(dev, 0x25, (0x2f8 >> 2)); // UART2 base
143 pnp_write_register(dev, 0x26, (2 << 4) | 0); // FDC + PP DMA
144 pnp_write_register(dev, 0x27, (6 << 4) | 7); // FDC + PP DMA
145 pnp_write_register(dev, 0x28, (4 << 4) | 3); // UART1,2 IRQ
146 /* These are the SMI status registers in the SIO: */
147 pnp_write_register(dev, 0x30, (0x600 >> 4)); // Runtime Register Block Base
149 pnp_write_register(dev, 0x31, 0x00); // GPIO1 DIR
150 pnp_write_register(dev, 0x32, 0x00); // GPIO1 POL
151 pnp_write_register(dev, 0x33, 0x40); // GPIO2 DIR
152 pnp_write_register(dev, 0x34, 0x00); // GPIO2 POL
153 pnp_write_register(dev, 0x35, 0xff); // GPIO3 DIR
154 pnp_write_register(dev, 0x36, 0x00); // GPIO3 POL
155 pnp_write_register(dev, 0x37, 0xe0); // GPIO4 DIR
156 pnp_write_register(dev, 0x38, 0x00); // GPIO4 POL
157 pnp_write_register(dev, 0x39, 0x80); // GPIO4 POL
159 pnp_exit_ext_func_mode(dev);
162 static void rcba_config(void)
164 /* Set up virtual channel 0 */
165 //RCBA32(0x0014) = 0x80000001;
166 //RCBA32(0x001c) = 0x03128010;
168 /* Device 1f interrupt pin register */
169 RCBA32(0x3100) = 0x00042220;
170 /* Device 1d interrupt pin register */
171 RCBA32(0x310c) = 0x00214321;
173 /* dev irq route register */
174 RCBA16(0x3140) = 0x0232;
175 RCBA16(0x3142) = 0x3246;
176 RCBA16(0x3144) = 0x0237;
177 RCBA16(0x3146) = 0x3201;
178 RCBA16(0x3148) = 0x3216;
181 RCBA8(0x31ff) = 0x03;
183 /* Enable upper 128bytes of CMOS */
184 RCBA32(0x3400) = (1 << 2);
186 /* Disable unused devices */
187 RCBA32(0x3418) = FD_PCIE6 | FD_PCIE5 | FD_PCIE3 | FD_PCIE2 |
188 FD_INTLAN | FD_ACMOD | FD_HDAUD | FD_PATA;
189 RCBA32(0x3418) |= (1 << 0); // Required.
191 /* Enable PCIe Root Port Clock Gate */
192 // RCBA32(0x341c) = 0x00000001;
194 /* This should probably go into the ACPI OS Init trap */
196 /* Set up I/O Trap #0 for 0xfe00 (SMIC) */
197 RCBA32(0x1e84) = 0x00020001;
198 RCBA32(0x1e80) = 0x0000fe01;
200 /* Set up I/O Trap #3 for 0x800-0x80c (Trap) */
201 RCBA32(0x1e9c) = 0x000200f0;
202 RCBA32(0x1e98) = 0x000c0801;
205 static void early_ich7_init(void)
210 // program secondary mlt XXX byte?
211 pci_write_config8(PCI_DEV(0, 0x1e, 0), 0x1b, 0x20);
213 // reset rtc power status
214 reg8 = pci_read_config8(PCI_DEV(0, 0x1f, 0), 0xa4);
216 pci_write_config8(PCI_DEV(0, 0x1f, 0), 0xa4, reg8);
218 // usb transient disconnect
219 reg8 = pci_read_config8(PCI_DEV(0, 0x1f, 0), 0xad);
221 pci_write_config8(PCI_DEV(0, 0x1f, 0), 0xad, reg8);
223 reg32 = pci_read_config32(PCI_DEV(0, 0x1d, 7), 0xfc);
224 reg32 |= (1 << 29) | (1 << 17);
225 pci_write_config32(PCI_DEV(0, 0x1d, 7), 0xfc, reg32);
227 reg32 = pci_read_config32(PCI_DEV(0, 0x1d, 7), 0xdc);
228 reg32 |= (1 << 31) | (1 << 27);
229 pci_write_config32(PCI_DEV(0, 0x1d, 7), 0xdc, reg32);
231 RCBA32(0x0088) = 0x0011d000;
232 RCBA16(0x01fc) = 0x060f;
233 RCBA32(0x01f4) = 0x86000040;
234 RCBA32(0x0214) = 0x10030549;
235 RCBA32(0x0218) = 0x00020504;
236 RCBA8(0x0220) = 0xc5;
237 reg32 = RCBA32(0x3410);
239 RCBA32(0x3410) = reg32;
240 reg32 = RCBA32(0x3430);
243 RCBA32(0x3430) = reg32;
244 RCBA32(0x3418) |= (1 << 0);
245 RCBA16(0x0200) = 0x2008;
246 RCBA8(0x2027) = 0x0d;
247 RCBA16(0x3e08) |= (1 << 7);
248 RCBA16(0x3e48) |= (1 << 7);
249 RCBA32(0x3e0e) |= (1 << 7);
250 RCBA32(0x3e4e) |= (1 << 7);
252 // next step only on ich7m b0 and later:
253 reg32 = RCBA32(0x2034);
254 reg32 &= ~(0x0f << 16);
256 RCBA32(0x2034) = reg32;
259 static void init_artec_dongle(void)
261 // Enable 4MB decoding
268 // Now, this needs to be included because it relies on the symbol
269 // __PRE_RAM__ being set during CAR stage (in order to compile the
270 // BSS free versions of the functions). Either rewrite the code
271 // to be always BSS free, or invent a flag that's better suited than
272 // __PRE_RAM__ to determine whether we're in ram init stage (stage 1)
274 #include "lib/cbmem.c"
276 void main(unsigned long bist)
286 early_superio_config();
288 /* Set up the console */
291 #if CONFIG_USBDEBUG_DIRECT
292 i82801gx_enable_usbdebug_direct(DBGP_DEFAULT);
293 early_usbdebug_direct_init();
298 /* Halt if there was a built in self test failure */
299 report_bist_failure(bist);
301 if (MCHBAR16(SSKPD) == 0xCAFE) {
302 printk(BIOS_DEBUG, "soft reset detected.\n");
306 /* Perform some early chipset initialization required
307 * before RAM initialization can work
309 i945_early_initialization();
311 /* This has to happen after i945_early_initialization() */
315 reg32 = inl(DEFAULT_PMBASE + 0x04);
316 printk(BIOS_DEBUG, "PM1_CNT: %08x\n", reg32);
317 if (((reg32 >> 10) & 7) == 5) {
318 #if CONFIG_HAVE_ACPI_RESUME
319 printk(BIOS_DEBUG, "Resume from S3 detected.\n");
321 /* Clear SLP_TYPE. This will break stage2 but
322 * we care for that when we get there.
324 outl(reg32 & ~(7 << 10), DEFAULT_PMBASE + 0x04);
327 printk(BIOS_DEBUG, "Resume from S3 detected, but disabled.\n");
331 /* Enable SPD ROMs and DDR-II DRAM */
334 #if CONFIG_DEFAULT_CONSOLE_LOGLEVEL > 8
335 dump_spd_registers();
338 sdram_initialize(boot_mode);
340 /* Perform some initialization that must run before stage2 */
343 /* This should probably go away. Until now it is required
344 * and mainboard specific
348 /* Chipset Errata! */
351 /* Initialize the internal PCIe links before we go into stage2 */
352 i945_late_initialization();
354 #if !CONFIG_HAVE_ACPI_RESUME
355 #if CONFIG_DEFAULT_CONSOLE_LOGLEVEL > 8
356 #if defined(DEBUG_RAM_SETUP)
357 sdram_dump_mchbar_registers();
360 /* This will not work if TSEG is in place! */
361 u32 tom = pci_read_config32(PCI_DEV(0,2,0), 0x5c);
363 printk(BIOS_DEBUG, "TOM: 0x%08x\n", tom);
364 ram_check(0x00000000, 0x000a0000);
365 ram_check(0x00100000, tom);
371 MCHBAR16(SSKPD) = 0xCAFE;
373 #if CONFIG_HAVE_ACPI_RESUME
374 /* Start address of high memory tables */
375 unsigned long high_ram_base = get_top_of_ram() - HIGH_MEMORY_SIZE;
377 /* If there is no high memory area, we didn't boot before, so
378 * this is not a resume. In that case we just create the cbmem toc.
380 if ((boot_mode == 2) && cbmem_reinit((u64)high_ram_base)) {
381 void *resume_backup_memory = cbmem_find(CBMEM_ID_RESUME);
383 /* copy 1MB - 64K to high tables ram_base to prevent memory corruption
384 * through stage 2. We could keep stuff like stack and heap in high tables
385 * memory completely, but that's a wonderful clean up task for another
388 if (resume_backup_memory)
389 memcpy(resume_backup_memory, (void *)CONFIG_RAMBASE, HIGH_MEMORY_SAVE);
391 /* Magic for S3 resume */
392 pci_write_config32(PCI_DEV(0, 0x00, 0), SKPAD, 0xcafed00d);