2 * This file is part of the coreboot project.
4 * Copyright (C) 2010 Advanced Micro Devices, Inc.
6 * This program is free software; you can redistribute it and/or modify
7 * it under the terms of the GNU General Public License as published by
8 * the Free Software Foundation; version 2 of the License.
10 * This program is distributed in the hope that it will be useful,
11 * but WITHOUT ANY WARRANTY; without even the implied warranty of
12 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
13 * GNU General Public License for more details.
15 * You should have received a copy of the GNU General Public License
16 * along with this program; if not, write to the Free Software
17 * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
20 //#define SYSTEM_TYPE 0 /* SERVER */
21 #define SYSTEM_TYPE 1 /* DESKTOP */
22 //#define SYSTEM_TYPE 2 /* MOBILE */
24 //used by incoherent_ht
25 #define FAM10_SCAN_PCI_BUS 0
26 #define FAM10_ALLOCATE_IO_RANGE 0
30 #include <device/pci_def.h>
31 #include <device/pci_ids.h>
33 #include <device/pnp_def.h>
34 #include <arch/romcc_io.h>
35 #include <cpu/x86/lapic.h>
36 #include <console/console.h>
37 #include <cpu/amd/model_10xxx_rev.h>
38 #include "northbridge/amd/amdfam10/raminit.h"
39 #include "northbridge/amd/amdfam10/amdfam10.h"
41 #include "cpu/x86/lapic/boot_cpu.c"
42 #include "northbridge/amd/amdfam10/reset_test.c"
43 #include <console/loglevel.h>
44 #include "cpu/x86/bist.h"
45 static int smbus_read_byte(u32 device, u32 address);
46 #include "superio/ite/it8718f/it8718f_early_serial.c"
48 #include "cpu/x86/mtrr/earlymtrr.c"
49 #include <cpu/amd/mtrr.h>
50 #include "northbridge/amd/amdfam10/setup_resource_map.c"
51 #include "southbridge/amd/rs780/rs780_early_setup.c"
52 #include "southbridge/amd/sb700/sb700_early_setup.c"
53 #include "northbridge/amd/amdfam10/debug.c"
55 static void activate_spd_rom(const struct mem_controller *ctrl) { }
57 static int spd_read_byte(u32 device, u32 address)
59 return smbus_read_byte(device, address);
62 #include "northbridge/amd/amdfam10/amdfam10.h"
63 #include "northbridge/amd/amdfam10/raminit_sysinfo_in_ram.c"
64 #include "northbridge/amd/amdfam10/amdfam10_pci.c"
65 #include "resourcemap.c"
66 #include "cpu/amd/quadcore/quadcore.c"
67 #include "cpu/amd/car/post_cache_as_ram.c"
68 #include "cpu/amd/microcode/microcode.c"
69 #include "cpu/amd/model_10xxx/update_microcode.c"
70 #include "cpu/amd/model_10xxx/init_cpus.c"
71 #include "northbridge/amd/amdfam10/early_ht.c"
72 #include "southbridge/amd/sb700/sb700_early_setup.c"
75 void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
77 struct sys_info *sysinfo = (struct sys_info *)(CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE);
78 static const u8 spd_addr[] = {RC00, DIMM0, DIMM2, 0, 0, DIMM1, DIMM3, 0, 0, };
79 u32 bsp_apicid = 0, val;
82 if (!cpu_init_detectedx && boot_cpu()) {
83 /* Nothing special needs to be done to find bus 0 */
84 /* Allow the HT devices to be found */
85 /* mov bsp to bus 0xff when > 8 nodes */
86 set_bsp_node_CHtExtNodeCfgEn();
94 bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo); /* mmconf is inited in init_cpus */
95 /* All cores run this but the BSP(node0,core0) is the only core that returns. */
103 it8718f_enable_serial(0, CONFIG_TTYS0_BASE);
107 sb700_enable_usbdebug(CONFIG_USBDEBUG_DEFAULT_PORT);
108 early_usbdebug_init();
112 printk(BIOS_DEBUG, "\n");
114 // dump_mem(CONFIG_DCACHE_RAM_BASE+CONFIG_DCACHE_RAM_SIZE-0x200, CONFIG_DCACHE_RAM_BASE+CONFIG_DCACHE_RAM_SIZE);
116 /* Halt if there was a built in self test failure */
117 report_bist_failure(bist);
121 printk(BIOS_DEBUG, "BSP Family_Model: %08x \n", val);
122 printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo,sysinfo+1);
123 printk(BIOS_DEBUG, "bsp_apicid = %02x \n", bsp_apicid);
124 printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx \n", cpu_init_detectedx);
126 /* Setup sysinfo defaults */
127 set_sysinfo_in_ram(0);
129 update_microcode(val);
135 amd_ht_init(sysinfo);
138 /* Setup nodes PCI space and start core 0 AP init. */
139 finalize_node_setup(sysinfo);
141 /* Setup any mainboard PCI settings etc. */
142 setup_mb_resource_map();
145 /* wait for all the APs core0 started by finalize_node_setup. */
146 /* FIXME: A bunch of cores are going to start output to serial at once.
147 It would be nice to fixup prink spinlocks for ROM XIP mode.
148 I think it could be done by putting the spinlock flag in the cache
149 of the BSP located right after sysinfo.
151 wait_all_core0_started();
153 #if CONFIG_LOGICAL_CPUS==1
154 /* Core0 on each node is configured. Now setup any additional cores. */
155 printk(BIOS_DEBUG, "start_other_cores()\n");
158 wait_all_other_cores_started(bsp_apicid);
163 /* run _early_setup before soft-reset. */
167 #if CONFIG_SET_FIDVID
168 msr = rdmsr(0xc0010071);
169 printk(BIOS_DEBUG, "\nBegin FIDVID MSR 0xc0010071 0x%08x 0x%08x \n", msr.hi, msr.lo);
171 /* FIXME: The sb fid change may survive the warm reset and only
172 need to be done once.*/
173 enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);
177 if (!warm_reset_detect(0)) { // BSP is node 0
178 init_fidvid_bsp(bsp_apicid, sysinfo->nodes);
180 init_fidvid_stage2(bsp_apicid, 0); // BSP is node 0
185 /* show final fid and vid */
186 msr=rdmsr(0xc0010071);
187 printk(BIOS_DEBUG, "End FIDVIDMSR 0xc0010071 0x%08x 0x%08x \n", msr.hi, msr.lo);
192 /* Reset for HT, FIDVID, PLL and errata changes to take affect. */
193 if (!warm_reset_detect(0)) {
194 print_info("...WARM RESET...\n\n\n");
196 die("After soft_reset_x - shouldn't see this message!!!\n");
201 /* It's the time to set ctrl in sysinfo now; */
202 printk(BIOS_DEBUG, "fill_mem_ctrl()\n");
203 fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);
207 // die("Die Before MCT init.");
209 printk(BIOS_DEBUG, "raminit_amdmct()\n");
210 raminit_amdmct(sysinfo);
214 dump_pci_device_range(PCI_DEV(0, 0x18, 0), 0, 0x200);
215 dump_pci_device_range(PCI_DEV(0, 0x18, 1), 0, 0x200);
216 dump_pci_device_range(PCI_DEV(0, 0x18, 2), 0, 0x200);
217 dump_pci_device_range(PCI_DEV(0, 0x18, 3), 0, 0x200);
220 // ram_check(0x00200000, 0x00200000 + (640 * 1024));
221 // ram_check(0x40200000, 0x40200000 + (640 * 1024));
224 // die("After MCT init before CAR disabled.");
226 rs780_before_pci_init();
227 sb700_before_pci_init();
230 printk(BIOS_DEBUG, "\n*** Yes, the copy/decompress is taking a while, FIXME!\n");
231 post_cache_as_ram(); // BSP switch stack to ram, copy then execute LB.
232 post_code(0x43); // Should never see this post code.