1 #if CONFIG_K8_REV_F_SUPPORT == 1
2 #define K8_REV_F_SUPPORT_F0_F1_WORKAROUND 0
7 #include <device/pci_def.h>
8 #include <device/pci_ids.h>
10 #include <device/pnp_def.h>
11 #include <arch/romcc_io.h>
12 #include <cpu/x86/lapic.h>
13 #include <pc80/mc146818rtc.h>
14 #include <console/console.h>
15 #include <cpu/amd/model_fxx_rev.h>
16 #include "southbridge/amd/amd8111/amd8111_early_smbus.c"
18 #include "northbridge/amd/amdk8/raminit.h"
19 #include "cpu/amd/model_fxx/apic_timer.c"
20 #include "cpu/x86/lapic/boot_cpu.c"
21 #include "northbridge/amd/amdk8/reset_test.c"
22 #include "cpu/x86/bist.h"
23 #include "lib/delay.c"
24 #include "northbridge/amd/amdk8/debug.c"
25 #include "cpu/x86/mtrr/earlymtrr.c"
26 #include <cpu/amd/mtrr.h>
27 #include "superio/winbond/w83627hf/w83627hf_early_serial.c"
28 #include "northbridge/amd/amdk8/setup_resource_map.c"
29 #include "southbridge/amd/amd8111/amd8111_early_ctrl.c"
31 #define SERIAL_DEV PNP_DEV(0x2e, W83627HF_SP1)
33 static void memreset_setup(void)
35 //GPIO on amd8111 to enable MEMRST ????
36 outb((1<<2)|(1<<0), SMBUS_IO_BASE + 0xc0 + 16); //REVC_MEMRST_EN=1
37 outb((1<<2)|(0<<0), SMBUS_IO_BASE + 0xc0 + 17);
40 static void memreset(int controllers, const struct mem_controller *ctrl) { }
42 static inline void activate_spd_rom(const struct mem_controller *ctrl)
44 #define SMBUS_HUB 0x18
46 unsigned device=(ctrl->channel0[0])>>8;
47 /* the very first write always get COL_STS=1 and ABRT_STS=1, so try another time*/
50 ret = smbus_write_byte(SMBUS_HUB, 0x01, device);
51 } while ((ret!=0) && (i-->0));
53 smbus_write_byte(SMBUS_HUB, 0x03, 0);
57 static inline void change_i2c_mux(unsigned device)
59 #define SMBUS_HUB 0x18
61 print_debug("change_i2c_mux i="); print_debug_hex8(device); print_debug("\n");
64 ret = smbus_write_byte(SMBUS_HUB, 0x01, device);
65 print_debug("change_i2c_mux 1 ret="); print_debug_hex32(ret); print_debug("\n");
66 } while ((ret!=0) && (i-->0));
67 ret = smbus_write_byte(SMBUS_HUB, 0x03, 0);
68 print_debug("change_i2c_mux 2 ret="); print_debug_hex32(ret); print_debug("\n");
72 static inline int spd_read_byte(unsigned device, unsigned address)
74 return smbus_read_byte(device, address);
77 #include "northbridge/amd/amdk8/amdk8.h"
78 #include "northbridge/amd/amdk8/incoherent_ht.c"
79 #include "northbridge/amd/amdk8/coherent_ht.c"
80 #include "northbridge/amd/amdk8/raminit_f.c"
81 #include "lib/generic_sdram.c"
82 #include "resourcemap.c"
83 #include "cpu/amd/dualcore/dualcore.c"
85 #include "cpu/amd/car/post_cache_as_ram.c"
86 #include "cpu/amd/model_fxx/init_cpus.c"
87 #include "cpu/amd/model_fxx/fidvid.c"
88 #include "southbridge/amd/amd8111/amd8111_enable_rom.c"
89 #include "northbridge/amd/amdk8/early_ht.c"
91 #define RC0 ((1<<0)<<8)
92 #define RC1 ((1<<1)<<8)
93 #define RC2 ((1<<2)<<8)
94 #define RC3 ((1<<3)<<8)
96 void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
98 static const uint16_t spd_addr[] = {
100 RC0|DIMM0, RC0|DIMM2, 0, 0,
101 RC0|DIMM1, RC0|DIMM3, 0, 0,
102 #if CONFIG_MAX_PHYSICAL_CPUS > 1
104 RC1|DIMM0, RC1|DIMM2, RC1|DIMM4, RC1|DIMM6,
105 RC1|DIMM1, RC1|DIMM3, RC1|DIMM5, RC1|DIMM7,
107 #if CONFIG_MAX_PHYSICAL_CPUS > 2
109 RC2|DIMM0, RC2|DIMM2, 0, 0,
110 RC2|DIMM1, RC2|DIMM3, 0, 0,
112 RC3|DIMM0, RC3|DIMM2, RC3|DIMM4, RC3|DIMM6,
113 RC3|DIMM1, RC3|DIMM3, RC3|DIMM5, RC3|DIMM7,
118 struct sys_info *sysinfo = (void*)(CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE);
120 unsigned bsp_apicid = 0;
121 #if CONFIG_SET_FIDVID
122 struct cpuid_result cpuid1;
125 if (!cpu_init_detectedx && boot_cpu()) {
126 /* Nothing special needs to be done to find bus 0 */
127 /* Allow the HT devices to be found */
128 enumerate_ht_chain();
129 amd8111_enable_rom();
133 bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);
135 w83627hf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
139 // dump_mem(CONFIG_DCACHE_RAM_BASE+CONFIG_DCACHE_RAM_SIZE-0x200, CONFIG_DCACHE_RAM_BASE+CONFIG_DCACHE_RAM_SIZE);
141 /* Halt if there was a built in self test failure */
142 report_bist_failure(bist);
144 printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo,sysinfo+1);
146 setup_mb_resource_map();
148 dump_pci_device(PCI_DEV(0, 0x18, 0));
149 dump_pci_device(PCI_DEV(0, 0x19, 0));
152 print_debug("bsp_apicid="); print_debug_hex8(bsp_apicid); print_debug("\n");
154 #if CONFIG_MEM_TRAIN_SEQ == 1
155 set_sysinfo_in_ram(0); // in BSP so could hold all ap until sysinfo is in ram
157 setup_coherent_ht_domain(); // routing table and start other core0
159 wait_all_core0_started();
160 #if CONFIG_LOGICAL_CPUS==1
161 // It is said that we should start core1 after all core0 launched
162 /* becase optimize_link_coherent_ht is moved out from setup_coherent_ht_domain,
163 * So here need to make sure last core0 is started, esp for two way system,
164 * (there may be apic id conflicts in that case)
167 wait_all_other_cores_started(bsp_apicid);
170 /* it will set up chains and store link pair for optimization later */
171 ht_setup_chains_x(sysinfo); // it will init sblnk and sbbusn, nodes, sbdn
174 //it your CPU min fid is 1G, you can change HT to 1G and FID to max one time.
175 needs_reset = optimize_link_coherent_ht();
176 needs_reset |= optimize_link_incoherent_ht(sysinfo);
179 #if CONFIG_SET_FIDVID
180 /* Check to see if processor is capable of changing FIDVID */
181 /* otherwise it will throw a GP# when reading FIDVID_STATUS */
182 cpuid1 = cpuid(0x80000007);
183 if ((cpuid1.edx & 0x6) == 0x6) {
186 /* Read FIDVID_STATUS */
188 msr=rdmsr(0xc0010042);
189 print_debug("begin msr fid, vid "); print_debug_hex32( msr.hi ); print_debug_hex32(msr.lo); print_debug("\n");
193 enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);
194 init_fidvid_bsp(bsp_apicid);
196 // show final fid and vid
199 msr=rdmsr(0xc0010042);
200 print_debug("end msr fid, vid "); print_debug_hex32( msr.hi ); print_debug_hex32(msr.lo); print_debug("\n");
204 print_debug("Changing FIDVID not supported\n");
209 needs_reset = optimize_link_coherent_ht();
210 needs_reset |= optimize_link_incoherent_ht(sysinfo);
212 // fidvid change will issue one LDTSTOP and the HT change will be effective too
214 print_info("ht reset -\n");
215 soft_reset_x(sysinfo->sbbusn, sysinfo->sbdn);
218 allow_all_aps_stop(bsp_apicid);
220 //It's the time to set ctrl in sysinfo now;
221 fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);
228 activate_spd_rom(&cpu[i]);
229 dump_smbus_registers();
234 for(i=1;i<256;i<<=1) {
236 dump_smbus_registers();
242 //do we need apci timer, tsc...., only debug need it for better output
243 /* all ap stopped? */
244 // init_timer(); // Need to use TMICT to synconize FID/VID
246 sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo);
253 // dump_pci_devices();
254 dump_pci_device_index_wait(PCI_DEV(0, 0x18, 2), 0x98);
255 dump_pci_device_index_wait(PCI_DEV(0, 0x19, 2), 0x98);
258 post_cache_as_ram(); // bsp swtich stack to ram and copy sysinfo ram now