AMD K8 platforms must use CAR so it makes sense to use the PRINK_IN_CAR

[coreboot.git] / src / mainboard / msi / ms9282 / Options.lb

diff --git a/src/mainboard/msi/ms9282/Options.lb b/src/mainboard/msi/ms9282/Options.lb
index 7671f6825b5eeffc0e3d6510debdbfa0cfa2bd11..2db8a2466435f391986f63f33c3d39719768f59e 100644 (file)
--- a/src/mainboard/msi/ms9282/Options.lb
+++ b/src/mainboard/msi/ms9282/Options.lb
@@ -1,5 +1,5 @@
 ##
-## This file is part of the LinuxBIOS project.
+## This file is part of the coreboot project.
 ##
 ## Copyright (C) 2006 AMD
 ## Written by Yinghai Lu <yinghailu@gmail.com> for AMD.
@@ -57,7 +57,7 @@ uses MAINBOARD_PART_NUMBER
 uses MAINBOARD_VENDOR
 uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
 uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
-uses LINUXBIOS_EXTRA_VERSION
+uses COREBOOT_EXTRA_VERSION
 uses _RAMBASE
 uses CONFIG_GDB_STUB
 uses CROSS_COMPILE
@@ -96,6 +96,12 @@ uses SB_HT_CHAIN_UNITID_OFFSET_ONLY
 #bx_b005+
 uses SB_HT_CHAIN_ON_BUS0
 
+# stepan 2007-04-12
+uses CONFIG_COMPRESSED_PAYLOAD_LZMA
+uses CONFIG_COMPRESSED_PAYLOAD_NRV2B
+uses CONFIG_PRECOMPRESSED_PAYLOAD
+uses CONFIG_USE_PRINTK_IN_CAR\r
+
 ## ROM_SIZE is the size of boot ROM that this board will use.
 #512K bytes
 default ROM_SIZE=524288
@@ -120,7 +126,7 @@ default FALLBACK_SIZE=0x40000
 default HAVE_FALLBACK_BOOT=1
 
 ##
-## Build code to reset the motherboard from linuxBIOS
+## Build code to reset the motherboard from coreboot
 ##
 default HAVE_HARD_RESET=1
 
@@ -142,7 +148,7 @@ default HAVE_MP_TABLE=1
 default HAVE_OPTION_TABLE=1
 
 ##
-## Move the default LinuxBIOS cmos range off of AMD RTC registers
+## Move the default coreboot cmos range off of AMD RTC registers
 ##
 default LB_CKS_RANGE_START=49
 default LB_CKS_RANGE_END=122
@@ -198,7 +204,6 @@ default ENABLE_APIC_EXT_ID=1
 default APIC_ID_OFFSET=0x10
 default LIFT_BSP_APIC_ID=0
 
-
 ##
 ## Build code to setup a generic IOAPIC
 ##
@@ -213,10 +218,10 @@ default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x1462
 default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x9282
 
 ###
-### LinuxBIOS layout values
+### coreboot layout values
 ###
 
-## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy.
+## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
 default ROM_IMAGE_SIZE = 65536
 
 ##
@@ -235,7 +240,7 @@ default HEAP_SIZE=0x4000
 default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
 
 ##
-## LinuxBIOS C code runs at this location in RAM
+## Coreboot C code runs at this location in RAM
 ##
 default _RAMBASE=0x00004000
 
@@ -262,7 +267,8 @@ default CONFIG_GDB_STUB=0
 ##
 ## The Serial Console
 ##
-
+default CONFIG_USE_PRINTK_IN_CAR=1
+\r
 # To Enable the Serial Console
 default CONFIG_CONSOLE_SERIAL8250=1
 
@@ -284,7 +290,7 @@ default TTYS0_BASE=0x3f8
 default TTYS0_LCS=0x3
 
 ##
-### Select the linuxBIOS loglevel
+### Select the coreboot loglevel
 ##
 ## EMERG      1   system is unusable
 ## ALERT      2   action must be taken immediately