AMD K8 platforms must use CAR so it makes sense to use the PRINK_IN_CAR

[coreboot.git] / src / mainboard / msi / ms9185 / Options.lb

diff --git a/src/mainboard/msi/ms9185/Options.lb b/src/mainboard/msi/ms9185/Options.lb
index 783d30a4278589343b8349e2fc4d4107ec63970e..c20b7d3868bd31ce4731cc716c460baffdf49798 100644 (file)
--- a/src/mainboard/msi/ms9185/Options.lb
+++ b/src/mainboard/msi/ms9185/Options.lb
@@ -1,5 +1,5 @@
 ##
-## This file is part of the LinuxBIOS project.
+## This file is part of the coreboot project.
 ##
 ## Copyright (C) 2006 AMD
 ## Written by Yinghai Lu <yinghailu@gmail.com> for AMD.
@@ -45,6 +45,7 @@ uses ROM_SECTION_OFFSET
 uses CONFIG_ROM_PAYLOAD
 uses CONFIG_ROM_PAYLOAD_START
 uses CONFIG_COMPRESSED_PAYLOAD_LZMA
+uses CONFIG_PRECOMPRESSED_PAYLOAD
 uses PAYLOAD_SIZE
 uses _ROMBASE
 uses XIP_ROM_SIZE
@@ -60,7 +61,7 @@ uses MAINBOARD_VENDOR
 uses MAINBOARD
 uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
 uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
-uses LINUXBIOS_EXTRA_VERSION
+uses COREBOOT_EXTRA_VERSION
 uses _RAMBASE
 uses TTYS0_BAUD
 uses TTYS0_BASE
@@ -103,7 +104,7 @@ uses LIFT_BSP_APIC_ID
 uses CONFIG_PCI_64BIT_PREF_MEM
 
 uses CONFIG_LB_MEM_TOPK
-
+uses CONFIG_USE_PRINTK_IN_CAR
 
 ###
 ### Build options
@@ -130,7 +131,7 @@ default CONFIG_LB_MEM_TOPK=2048
 default HAVE_FALLBACK_BOOT=1
 
 ##
-## Build code to reset the motherboard from linuxBIOS
+## Build code to reset the motherboard from coreboot
 ##
 default HAVE_HARD_RESET=1
 
@@ -157,7 +158,7 @@ default HAVE_MP_TABLE=1
 default HAVE_OPTION_TABLE=1
 
 ##
-## Move the default LinuxBIOS cmos range off of AMD RTC registers
+## Move the default coreboot cmos range off of AMD RTC registers
 ##
 default LB_CKS_RANGE_START=49
 default LB_CKS_RANGE_END=122
@@ -221,7 +222,7 @@ default USE_DCACHE_RAM=1
 default DCACHE_RAM_BASE=0xcc000
 default DCACHE_RAM_SIZE=0x04000
 default DCACHE_RAM_GLOBAL_VAR_SIZE=0x01000
-default CONFIG_USE_INIT=0
+default CONFIG_USE_INIT=0\r
 
 ##
 ## Build code to setup a generic IOAPIC
@@ -237,10 +238,10 @@ default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x1022
 default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2b80
 
 ###
-### LinuxBIOS layout values
+### coreboot layout values
 ###
 
-## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy.
+## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
 default ROM_IMAGE_SIZE = 65536
 
 ##
@@ -259,7 +260,7 @@ default HEAP_SIZE=0x8000
 default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
 
 ##
-## LinuxBIOS C code runs at this location in RAM
+## Coreboot C code runs at this location in RAM
 ##
 default _RAMBASE=0x00100000
 
@@ -286,6 +287,7 @@ default CONFIG_GDB_STUB=0
 ##
 ## The Serial Console
 ##
+default CONFIG_USE_PRINTK_IN_CAR=1
 
 # To Enable the Serial Console
 default CONFIG_CONSOLE_SERIAL8250=1
@@ -308,7 +310,7 @@ default TTYS0_BASE=0x3f8
 default TTYS0_LCS=0x3
 
 ##
-### Select the linuxBIOS loglevel
+### Select the coreboot loglevel
 ##
 ## EMERG      1   system is unusable
 ## ALERT      2   action must be taken immediately