1 uses CONFIG_HAVE_MP_TABLE
3 uses CONFIG_HAVE_PIRQ_TABLE
4 uses CONFIG_USE_FALLBACK_IMAGE
5 uses CONFIG_HAVE_FALLBACK_BOOT
6 uses CONFIG_HAVE_HARD_RESET
7 uses CONFIG_IRQ_SLOT_COUNT
8 uses CONFIG_HAVE_OPTION_TABLE
10 uses CONFIG_MAX_PHYSICAL_CPUS
13 uses CONFIG_FALLBACK_SIZE
15 uses CONFIG_ROM_SECTION_SIZE
16 uses CONFIG_ROM_IMAGE_SIZE
17 uses CONFIG_ROM_SECTION_SIZE
18 uses CONFIG_ROM_SECTION_OFFSET
19 uses CONFIG_ROM_PAYLOAD
20 uses CONFIG_ROM_PAYLOAD_START
21 uses CONFIG_COMPRESSED_PAYLOAD_LZMA
22 uses CONFIG_PRECOMPRESSED_PAYLOAD
23 uses CONFIG_PAYLOAD_SIZE
25 uses CONFIG_XIP_ROM_SIZE
26 uses CONFIG_XIP_ROM_BASE
27 uses CONFIG_STACK_SIZE
29 uses CONFIG_USE_OPTION_TABLE
30 uses CONFIG_LB_CKS_RANGE_START
31 uses CONFIG_LB_CKS_RANGE_END
32 uses CONFIG_LB_CKS_LOC
34 uses CONFIG_MAINBOARD_PART_NUMBER
35 uses CONFIG_MAINBOARD_VENDOR
36 uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
37 uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
38 uses COREBOOT_EXTRA_VERSION
40 uses CONFIG_TTYS0_BAUD
41 uses CONFIG_TTYS0_BASE
43 uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
44 uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
45 uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
46 uses CONFIG_CONSOLE_SERIAL8250
47 uses CONFIG_HAVE_INIT_TIMER
49 uses CONFIG_CROSS_COMPILE
53 uses CONFIG_USE_DCACHE_RAM
54 uses CONFIG_DCACHE_RAM_BASE
55 uses CONFIG_DCACHE_RAM_SIZE
57 uses CONFIG_USE_PRINTK_IN_CAR
59 ## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
60 default CONFIG_ROM_SIZE=524288
67 ## CONFIG_FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
69 default CONFIG_FALLBACK_SIZE=131072
72 ## Build code for the fallback boot
74 default CONFIG_HAVE_FALLBACK_BOOT=1
77 ## Build code to reset the motherboard from coreboot
79 default CONFIG_HAVE_HARD_RESET=1
82 ## Build code to export a programmable irq routing table
84 default CONFIG_HAVE_PIRQ_TABLE=1
85 default CONFIG_IRQ_SLOT_COUNT=9
88 ## Build code to export an x86 MP table
89 ## Useful for specifying IRQ routing values
91 default CONFIG_HAVE_MP_TABLE=1
94 ## Build code to export a CMOS option table
96 default CONFIG_HAVE_OPTION_TABLE=1
99 ## Move the default coreboot cmos range off of AMD RTC registers
101 default CONFIG_LB_CKS_RANGE_START=49
102 default CONFIG_LB_CKS_RANGE_END=122
103 default CONFIG_LB_CKS_LOC=123
106 ## Build code for SMP support
107 ## Only worry about 2 micro processors
110 default CONFIG_MAX_CPUS=2
111 default CONFIG_MAX_PHYSICAL_CPUS=2
114 ## Build code to setup a generic IOAPIC
116 default CONFIG_IOAPIC=1
119 ## enable CACHE_AS_RAM specifics
121 default CONFIG_USE_DCACHE_RAM=1
122 default CONFIG_DCACHE_RAM_BASE=0xcf000
123 default CONFIG_DCACHE_RAM_SIZE=0x1000
124 default CONFIG_USE_INIT=0
127 ## Clean up the motherboard id strings
129 #default CONFIG_MAINBOARD_PART_NUMBER="HDAMA"
130 #default CONFIG_MAINBOARD_VENDOR="ARIMA"
131 #default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x161f
132 #default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x3016
135 ### coreboot layout values
138 ## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
139 default CONFIG_ROM_IMAGE_SIZE = 65536
142 ## Use a small 8K stack
144 default CONFIG_STACK_SIZE=0x2000
147 ## Use a small 16K heap
149 default CONFIG_HEAP_SIZE=0x4000
152 ## Only use the option table in a normal image
154 default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
157 ## Coreboot C code runs at this location in RAM
159 default CONFIG_RAMBASE=0x00004000
162 ## Load the payload from the ROM
164 default CONFIG_ROM_PAYLOAD = 1
167 ### Defaults of options that you may want to override in the target config file
171 ## The default compiler
173 #default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
174 #default CONFIG_HOSTCC="gcc"
177 ## Disable the gdb stub by default
179 default CONFIG_GDB_STUB=0
181 default CONFIG_USE_PRINTK_IN_CAR=1
184 ## The Serial Console
187 # To Enable the Serial Console
188 default CONFIG_CONSOLE_SERIAL8250=1
190 ## Select the serial console baud rate
191 default CONFIG_TTYS0_BAUD=115200
192 #default CONFIG_TTYS0_BAUD=57600
193 #default CONFIG_TTYS0_BAUD=38400
194 #default CONFIG_TTYS0_BAUD=19200
195 #default CONFIG_TTYS0_BAUD=9600
196 #default CONFIG_TTYS0_BAUD=4800
197 #default CONFIG_TTYS0_BAUD=2400
198 #default CONFIG_TTYS0_BAUD=1200
200 # Select the serial console base port
201 default CONFIG_TTYS0_BASE=0x3f8
203 # Select the serial protocol
204 # This defaults to 8 data bits, 1 stop bit, and no parity
205 default CONFIG_TTYS0_LCS=0x3
208 ### Select the coreboot loglevel
210 ## EMERG 1 system is unusable
211 ## ALERT 2 action must be taken immediately
212 ## CRIT 3 critical conditions
213 ## ERR 4 error conditions
214 ## WARNING 5 warning conditions
215 ## NOTICE 6 normal but significant condition
216 ## INFO 7 informational
217 ## CONFIG_DEBUG 8 debug-level messages
218 ## SPEW 9 Way too many details
220 ## Request this level of debugging output
221 default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
222 ## At a maximum only compile in this level of debugging
223 default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
226 ## Select power on after power fail setting
227 default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
234 default CONFIG_CBFS=0