-#if 0
-static void setup_coherent_ht_domain(void)
-{
- static const unsigned int register_values[] = {
- /* Routing Table Node i
- * F0:0x40 i = 0,
- * F0:0x44 i = 1,
- * F0:0x48 i = 2,
- * F0:0x4c i = 3,
- * F0:0x50 i = 4,
- * F0:0x54 i = 5,
- * F0:0x58 i = 6,
- * F0:0x5c i = 7
- * [ 0: 3] Request Route
- * [0] Route to this node
- * [1] Route to Link 0
- * [2] Route to Link 1
- * [3] Route to Link 2
- * [11: 8] Response Route
- * [0] Route to this node
- * [1] Route to Link 0
- * [2] Route to Link 1
- * [3] Route to Link 2
- * [19:16] Broadcast route
- * [0] Route to this node
- * [1] Route to Link 0
- * [2] Route to Link 1
- * [3] Route to Link 2
- */
- PCI_ADDR(0, 0x18, 0, 0x40), 0xfff0f0f0, 0x00010101,
- PCI_ADDR(0, 0x18, 0, 0x44), 0xfff0f0f0, 0x00010101,
- PCI_ADDR(0, 0x18, 0, 0x48), 0xfff0f0f0, 0x00010101,
- PCI_ADDR(0, 0x18, 0, 0x4c), 0xfff0f0f0, 0x00010101,
- PCI_ADDR(0, 0x18, 0, 0x50), 0xfff0f0f0, 0x00010101,
- PCI_ADDR(0, 0x18, 0, 0x54), 0xfff0f0f0, 0x00010101,
- PCI_ADDR(0, 0x18, 0, 0x58), 0xfff0f0f0, 0x00010101,
- PCI_ADDR(0, 0x18, 0, 0x5c), 0xfff0f0f0, 0x00010101,
-
- /* Hypetransport Transaction Control Register
- * F0:0x68
- * [ 0: 0] Disable read byte probe
- * 0 = Probes issues
- * 1 = Probes not issued
- * [ 1: 1] Disable Read Doubleword probe
- * 0 = Probes issued
- * 1 = Probes not issued
- * [ 2: 2] Disable write byte probes
- * 0 = Probes issued
- * 1 = Probes not issued
- * [ 3: 3] Disable Write Doubleword Probes
- * 0 = Probes issued
- * 1 = Probes not issued.
- * [ 4: 4] Disable Memroy Controller Target Start
- * 0 = TgtStart packets are generated
- * 1 = TgtStart packets are not generated.
- * [ 5: 5] CPU1 Enable
- * 0 = Second CPU disabled or not present
- * 1 = Second CPU enabled.
- * [ 6: 6] CPU Request PassPW
- * 0 = CPU requests do not pass posted writes
- * 1 = CPU requests pass posted writes.
- * [ 7: 7] CPU read Respons PassPW
- * 0 = CPU Responses do not pass posted writes
- * 1 = CPU responses pass posted writes.
- * [ 8: 8] Disable Probe Memory Cancel
- * 0 = Probes may generate MemCancels
- * 1 = Probes may not generate MemCancels
- * [ 9: 9] Disable Remote Probe Memory Cancel.
- * 0 = Probes hitting dirty blocks generate memory cancel packets
- * 1 = Only probed caches on the same node as the memory controller
- * generate cancel packets.
- * [10:10] Disable Fill Probe
- * 0 = Probes issued for cache fills
- * 1 = Probes not issued for cache fills.
- * [11:11] Response PassPw
- * 0 = Downstream response PassPW based on original request
- * 1 = Downstream response PassPW set to 1
- * [12:12] Change ISOC to Ordered
- * 0 = Bit 1 of coherent HT RdSz/WrSz command used for iosynchronous prioritization
- * 1 = Bit 1 of coherent HT RdSz/WrSz command used for ordering.
- * [14:13] Buffer Release Priority select
- * 00 = 64
- * 01 = 16
- * 10 = 8
- * 11 = 2
- * [15:15] Limit Coherent HT Configuration Space Range
- * 0 = No coherent HT configuration space restrictions
- * 1 = Limit coherent HT configuration space based on node count
- * [16:16] Local Interrupt Conversion Enable.
- * 0 = ExtInt/NMI interrups unaffected.
- * 1 = ExtInt/NMI broadcat interrupts converted to LINT0/1
- * [17:17] APIC Extended Broadcast Enable.
- * 0 = APIC broadcast is 0F
- * 1 = APIC broadcast is FF
- * [18:18] APIC Extended ID Enable
- * 0 = APIC ID is 4 bits.
- * 1 = APIC ID is 8 bits.
- * [19:19] APIC Extended Spurious Vector Enable
- * 0 = Lower 4 bits of spurious vector are read-only 1111
- * 1 = Lower 4 bits of spurious vecotr are writeable.
- * [20:20] Sequence ID Source Node Enable
- * 0 = Normal operation
- * 1 = Keep SeqID on routed packets for debugging.
- * [22:21] Downstream non-posted request limit
- * 00 = No limit
- * 01 = Limited to 1
- * 10 = Limited to 4
- * 11 = Limited to 8
- * [23:23] RESERVED
- * [25:24] Medium-Priority Bypass Count
- * - Maximum # of times a medium priority access can pass a low
- * priority access before Medium-Priority mode is disabled for one access.
- * [27:26] High-Priority Bypass Count
- * - Maximum # of times a high prioirty access can pass a medium or low
- * priority access before High-prioirty mode is disabled for one access.
- * [28:28] Enable High Priority CPU Reads
- * 0 = Cpu reads are medium prioirty
- * 1 = Cpu reads are high prioirty
- * [29:29] Disable Low Priority Writes
- * 0 = Non-isochronous writes are low priority
- * 1 = Non-isochronous writes are medium prioirty
- * [30:30] Disable High Priority Isochronous writes
- * 0 = Isochronous writes are high priority
- * 1 = Isochronous writes are medium priority
- * [31:31] Disable Medium Priority Isochronous writes
- * 0 = Isochronous writes are medium are high
- * 1 = With bit 30 set makes Isochrouns writes low priority.
- */
- PCI_ADDR(0, 0x18, 0, 0x68), 0x00800000, 0x0f00840f,
- /* HT Initialization Control Register
- * F0:0x6C ok...
- * [ 0: 0] Routing Table Disable
- * 0 = Packets are routed according to routing tables
- * 1 = Packets are routed according to the default link field
- * [ 1: 1] Request Disable (BSP should clear this)
- * 0 = Request packets may be generated
- * 1 = Request packets may not be generated.
- * [ 3: 2] Default Link (Read-only)
- * 00 = LDT0
- * 01 = LDT1
- * 10 = LDT2
- * 11 = CPU on same node
- * [ 4: 4] Cold Reset
- * - Scratch bit cleared by a cold reset
- * [ 5: 5] BIOS Reset Detect
- * - Scratch bit cleared by a cold reset
- * [ 6: 6] INIT Detect
- * - Scratch bit cleared by a warm or cold reset not by an INIT
- *
- */
- PCI_ADDR(0, 0x18, 0, 0x6C), 0xffffff8c, 0x00000000 | (1 << 6) |(1 << 5)| (1 << 4),
- /* LDTi Capabilities Registers
- * F0:0x80 i = 0,
- * F0:0xA0 i = 1,
- * F0:0xC0 i = 2,
- */
- /* LDTi Link Control Registrs
- * F0:0x84 i = 0,
- * F0:0xA4 i = 1,
- * F0:0xC4 i = 2,
- * [ 1: 1] CRC Flood Enable
- * 0 = Do not generate sync packets on CRC error
- * 1 = Generate sync packets on CRC error
- * [ 2: 2] CRC Start Test (Read-Only)
- * [ 3: 3] CRC Force Frame Error
- * 0 = Do not generate bad CRC
- * 1 = Generate bad CRC
- * [ 4: 4] Link Failure
- * 0 = No link failure detected
- * 1 = Link failure detected
- * [ 5: 5] Initialization Complete
- * 0 = Initialization not complete
- * 1 = Initialization complete
- * [ 6: 6] Receiver off
- * 0 = Recevier on
- * 1 = Receiver off
- * [ 7: 7] Transmitter Off
- * 0 = Transmitter on
- * 1 = Transmitter off
- * [ 9: 8] CRC_Error
- * 00 = No error
- * [0] = 1 Error on byte lane 0
- * [1] = 1 Error on byte lane 1
- * [12:12] Isochrnous Enable (Read-Only)
- * [13:13] HT Stop Tristate Enable
- * 0 = Driven during an LDTSTOP_L
- * 1 = Tristated during and LDTSTOP_L
- * [14:14] Extended CTL Time
- * 0 = CTL is asserted for 16 bit times during link initialization
- * 1 = CTL is asserted for 50us during link initialization
- * [18:16] Max Link Width In (Read-Only?)
- * 000 = 8 bit link
- * 001 = 16bit link
- * [19:19] Doubleword Flow Control in (Read-Only)
- * 0 = This link does not support doubleword flow control
- * 1 = This link supports doubleword flow control
- * [22:20] Max Link Width Out (Read-Only?)
- * 000 = 8 bit link
- * 001 = 16bit link
- * [23:23] Doubleworld Flow Control out (Read-Only)
- * 0 = This link does not support doubleword flow control
- * 1 = This link supports doubleworkd flow control
- * [26:24] Link Width In
- * 000 = Use 8 bits
- * 001 = Use 16 bits
- * 010 = reserved
- * 011 = Use 32 bits
- * 100 = Use 2 bits
- * 101 = Use 4 bits
- * 110 = reserved
- * 111 = Link physically not connected
- * [27:27] Doubleword Flow Control In Enable
- * 0 = Doubleword flow control disabled
- * 1 = Doubleword flow control enabled (Not currently supported)
- * [30:28] Link Width Out
- * 000 = Use 8 bits
- * 001 = Use 16 bits
- * 010 = reserved
- * 011 = Use 32 bits
- * 100 = Use 2 bits
- * 101 = Use 4 bits
- * 110 = reserved
- * 111 = Link physically not connected
- * [31:31] Doubleworld Flow Control Out Enable
- * 0 = Doubleworld flow control disabled
- * 1 = Doubleword flow control enabled (Not currently supported)
- */
- PCI_ADDR(0, 0x18, 0, 0x84), 0x00009c05, 0x11110020,
- /* LDTi Frequency/Revision Registers
- * F0:0x88 i = 0,
- * F0:0xA8 i = 1,
- * F0:0xC8 i = 2,
- * [ 4: 0] Minor Revision
- * Contains the HT Minor revision
- * [ 7: 5] Major Revision
- * Contains the HT Major revision
- * [11: 8] Link Frequency (Takes effect the next time the link is reconnected)
- * 0000 = 200Mhz
- * 0001 = reserved
- * 0010 = 400Mhz
- * 0011 = reserved
- * 0100 = 600Mhz
- * 0101 = 800Mhz
- * 0110 = 1000Mhz
- * 0111 = reserved
- * 1000 = reserved
- * 1001 = reserved
- * 1010 = reserved
- * 1011 = reserved
- * 1100 = reserved
- * 1101 = reserved
- * 1110 = reserved
- * 1111 = 100 Mhz
- * [15:12] Error (Not currently Implemented)
- * [31:16] Indicates the frequency capabilities of the link
- * [16] = 1 encoding 0000 of freq supported
- * [17] = 1 encoding 0001 of freq supported
- * [18] = 1 encoding 0010 of freq supported
- * [19] = 1 encoding 0011 of freq supported
- * [20] = 1 encoding 0100 of freq supported
- * [21] = 1 encoding 0101 of freq supported
- * [22] = 1 encoding 0110 of freq supported
- * [23] = 1 encoding 0111 of freq supported
- * [24] = 1 encoding 1000 of freq supported
- * [25] = 1 encoding 1001 of freq supported
- * [26] = 1 encoding 1010 of freq supported
- * [27] = 1 encoding 1011 of freq supported
- * [28] = 1 encoding 1100 of freq supported
- * [29] = 1 encoding 1101 of freq supported
- * [30] = 1 encoding 1110 of freq supported
- * [31] = 1 encoding 1111 of freq supported
- */
- PCI_ADDR(0, 0x18, 0, 0x88), 0xfffff0ff, 0x00000200,
- /* LDTi Feature Capability
- * F0:0x8C i = 0,
- * F0:0xAC i = 1,
- * F0:0xCC i = 2,
- */
- /* LDTi Buffer Count Registers
- * F0:0x90 i = 0,
- * F0:0xB0 i = 1,
- * F0:0xD0 i = 2,
- */
- /* LDTi Bus Number Registers
- * F0:0x94 i = 0,
- * F0:0xB4 i = 1,
- * F0:0xD4 i = 2,
- * For NonCoherent HT specifies the bus number downstream (behind the host bridge)
- * [ 0: 7] Primary Bus Number
- * [15: 8] Secondary Bus Number
- * [23:15] Subordiante Bus Number
- * [31:24] reserved
- */
- PCI_ADDR(0, 0x18, 0, 0x94), 0xff000000, 0x00ff0000,
- /* LDTi Type Registers
- * F0:0x98 i = 0,
- * F0:0xB8 i = 1,
- * F0:0xD8 i = 2,
- */
- };
- int i;
- int max;
- print_debug("setting up coherent ht domain....\r\n");
- max = sizeof(register_values)/sizeof(register_values[0]);
- for(i = 0; i < max; i += 3) {
- device_t dev;
- unsigned where;
- unsigned long reg;
-#if 0
- print_debug_hex32(register_values[i]);
- print_debug(" <-");
- print_debug_hex32(register_values[i+2]);
- print_debug("\r\n");
-#endif
- dev = register_values[i] & ~0xff;
- where = register_values[i] & 0xff;
- reg = pci_read_config32(dev, where);
- reg &= register_values[i+1];
- reg |= register_values[i+2];
- pci_write_config32(dev, where, reg);
-#if 0
- reg = pci_read_config32(register_values[i]);
- reg &= register_values[i+1];
- reg |= register_values[i+2] & ~register_values[i+1];
- pci_write_config32(register_values[i], reg);
-#endif
- }
- print_debug("done.\r\n");
-}
-#else
-/* coherent hypertransport initialization for AMD64
- * written by Stefan Reinauer <stepan@openbios.info>
- * (c) 2003 by SuSE Linux AG
+/* coherent hypertransport initialization for AMD64
+ *
+ * written by Stefan Reinauer <stepan@openbios.org>
+ * (c) 2003-2004 by SuSE Linux AG
+ *
+ * (c) 2004 Tyan Computer
+ * 2004.12 yhlu added support to create routing table dynamically.
+ * it also support 8 ways too. (8 ways ladder or 8 ways crossbar)
*
* This code is licensed under GPL.
*/
*
* nodes : 1 2 4 6 8
* org. : 1x1 2x1 2x2 2x3 2x4
- *
+ Ladder:
+ CPU7-------------CPU6
+ | |
+ | |
+ | |
+ | |
+ | |
+ | |
+ CPU5-------------CPU4
+ | |
+ | |
+ | |
+ | |
+ | |
+ | |
+ CPU3-------------CPU2
+ | |
+ | |
+ | |
+ | |
+ | |
+ | |
+ CPU1-------------CPU0
+ CROSS_BAR_47_56:
+ CPU7-------------CPU6
+ | \____ ___/ |
+ | \ / |
+ | \/ |
+ | /\ |
+ | / \ |
+ | ____/ \___ |
+ CPU5 CPU4
+ | |
+ | |
+ | |
+ | |
+ | |
+ | |
+ CPU3-------------CPU2
+ | |
+ | |
+ | |
+ | |
+ | |
+ | |
+ CPU1-------------CPU0
*/
-#if 0
-#include "compat.h"
-#endif
-
#include <device/pci_def.h>
+#include <device/pci_ids.h>
+#include <device/hypertransport_def.h>
+#include <stdlib.h>
#include "arch/romcc_io.h"
+#include <pc80/mc146818rtc.h>
+#if CONFIG_HAVE_OPTION_TABLE
+#include "option_table.h"
+#endif
+#include "amdk8.h"
-/* when generating a temporary row configuration we
- * don't want broadcast to be enabled for that node.
- */
-
-#define generate_temp_row(x...) ((generate_row(x)&(~0x0f0000))|0x010000)
-#define clear_temp_row(x) fill_row(x,7,DEFAULT)
#define enable_bsp_routing() enable_routing(0)
#define NODE_HT(x) PCI_DEV(0,24+x,0)
#define DEFAULT 0x00010101 /* default row entry */
-typedef uint8_t u8;
-typedef uint32_t u32;
-typedef int8_t bool;
-#define TRUE (-1)
-#define FALSE (0)
+#ifndef CROSS_BAR_47_56
+ #define CROSS_BAR_47_56 0
+#endif
+
+#ifndef TRY_HIGH_FIRST
+ #define TRY_HIGH_FIRST 0
+#endif
+
+#ifndef CONFIG_K8_HT_FREQ_1G_SUPPORT
+ #define CONFIG_K8_HT_FREQ_1G_SUPPORT 0
+#endif
+
+#ifndef K8_HT_CHECK_PENDING_LINK
+ #if CONFIG_MAX_PHYSICAL_CPUS >= 4
+ #define K8_HT_CHECK_PENDING_LINK 1
+ #else
+ #define K8_HT_CHECK_PENDING_LINK 0
+ #endif
+#endif
+
+#ifndef CONFIG_MAX_PHYSICAL_CPUS_4_BUT_MORE_INSTALLED
+ #define CONFIG_MAX_PHYSICAL_CPUS_4_BUT_MORE_INSTALLED 0
+#endif
+
+#ifndef CONFIG_ENABLE_APIC_EXT_ID
+ #define CONFIG_ENABLE_APIC_EXT_ID 0
+#endif
+
+
+static inline void print_linkn (const char *strval, uint8_t byteval)
+{
+ printk(BIOS_DEBUG, "%s%02x\n", strval, byteval);
+}
static void disable_probes(void)
{
* they don't make sense if only one cpu is available
*/
- /* Hypetransport Transaction Control Register
+ /* Hypetransport Transaction Control Register
* F0:0x68
* [ 0: 0] Disable read byte probe
* 0 = Probes issues
u32 val;
- print_debug("Disabling read/write/fill probes for UP... ");
+ print_spew("Disabling read/write/fill probes for UP... ");
+
+ val=pci_read_config32(NODE_HT(0), HT_TRANSACTION_CONTROL);
+ val |= HTTC_DIS_FILL_P | HTTC_DIS_RMT_MEM_C | HTTC_DIS_P_MEM_C |
+ HTTC_DIS_MTS | HTTC_DIS_WR_DW_P | HTTC_DIS_WR_B_P |
+ HTTC_DIS_RD_DW_P | HTTC_DIS_RD_B_P;
+ pci_write_config32(NODE_HT(0), HT_TRANSACTION_CONTROL, val);
+
+ print_spew("done.\n");
- val=pci_read_config32(NODE_HT(0), 0x68);
- val |= 0x0000040f;
- pci_write_config32(NODE_HT(0), 0x68, val);
+}
+
+#if 0
+static void enable_apic_ext_id(u8 node)
+{
+#if CONFIG_ENABLE_APIC_EXT_ID==1
+#warning "FIXME Is the right place to enable apic ext id here?"
- print_debug("done.\r\n");
+ u32 val;
+ val = pci_read_config32(NODE_HT(node), 0x68);
+ val |= (HTTC_APIC_EXT_SPUR | HTTC_APIC_EXT_ID | HTTC_APIC_EXT_BRD_CST);
+ pci_write_config32(NODE_HT(node), 0x68, val);
+#endif
}
+#endif
static void enable_routing(u8 node)
{
*
*/
- /* Enable routing table for BSP */
- print_debug("Enabling routing table for node ");
- print_debug_hex32(node);
+ /* Enable routing table */
+ print_spew("Enabling routing table for node ");
+ print_spew_hex8(node);
val=pci_read_config32(NODE_HT(node), 0x6c);
- val |= (1 << 6) | (1 << 5) | (1 << 4);
-#if 0
val &= ~((1<<1)|(1<<0));
-#else
- /* Don't enable requests here as the indicated processor starts booting */
- val &= ~(1<<0);
-#endif
pci_write_config32(NODE_HT(node), 0x6c, val);
- print_debug(" done.\r\n");
+ print_spew(" done.\n");
+}
+
+#if CONFIG_MAX_PHYSICAL_CPUS > 1
+static void fill_row(u8 node, u8 row, u32 value)
+{
+ pci_write_config32(NODE_HT(node), 0x40+(row<<2), value);
+}
+
+static u8 link_to_register(int ldt)
+{
+ /*
+ * [ 0: 3] Request Route
+ * [0] Route to this node
+ * [1] Route to Link 0
+ * [2] Route to Link 1
+ * [3] Route to Link 2
+ */
+
+ if (ldt&0x08) return 0x40;
+ if (ldt&0x04) return 0x20;
+ if (ldt&0x02) return 0x00;
+
+ /* we should never get here */
+ print_spew("Unknown Link\n");
+ return 0;
+}
+
+static u32 get_row(u8 node, u8 row)
+{
+ return pci_read_config32(NODE_HT(node), 0x40+(row<<2));
}
-#if MAX_CPUS > 1
+static int link_connection(u8 src, u8 dest)
+{
+ return get_row(src, dest) & 0x0f;
+}
static void rename_temp_node(u8 node)
{
- u32 val;
+ uint32_t val;
- print_debug("Renaming current temp node to ");
- print_debug_hex32(node);
+ print_spew("Renaming current temporary node to ");
+ print_spew_hex8(node);
val=pci_read_config32(NODE_HT(7), 0x60);
val &= (~7); /* clear low bits. */
- val |= node; /* new node */
+ val |= node; /* new node */
pci_write_config32(NODE_HT(7), 0x60, val);
- print_debug(" done.\r\n");
-
-
+ print_spew(" done.\n");
}
-static bool check_connection(u8 src, u8 dest, u8 link)
+static int verify_connection(u8 dest)
{
- /* this function does 2 things:
- * 1) detect whether the coherent HT link is connected.
- * After this step follows a small idle loop.
- * 2) verify that the coherent hypertransport link
- * is established and actually working by reading the
- * remote node's vendor/device id
- */
-
-#define UP 0x00
-#define ACROSS 0x20
-#define DOWN 0x40
-
+ /* See if we have a valid connection to dest */
u32 val;
-
- /* 1) */
- val=pci_read_config32(NODE_HT(src), 0x98+link);
- if ( (val&0x17) != 0x03)
- return 0;
-
- /* idle loop to make sure the link is established */
- for (val=0;val<16;val++);
- /* 2) */
- val=pci_read_config32(NODE_HT(dest),0);
+ /* Verify that the coherent hypertransport link is
+ * established and actually working by reading the
+ * remode node's vendor/device id
+ */
+ val = pci_read_config32(NODE_HT(dest),0);
if(val != 0x11001022)
return 0;
return 1;
}
-static unsigned int generate_row(u8 node, u8 row, u8 maxnodes)
+static uint16_t read_freq_cap(device_t dev, uint8_t pos)
{
- /* Routing Table Node i
- *
- * F0: 0x40, 0x44, 0x48, 0x4c, 0x50, 0x54, 0x58, 0x5c
- * i: 0, 1, 2, 3, 4, 5, 6, 7
- *
- * [ 0: 3] Request Route
- * [0] Route to this node
- * [1] Route to Link 0
- * [2] Route to Link 1
- * [3] Route to Link 2
- * [11: 8] Response Route
- * [0] Route to this node
- * [1] Route to Link 0
- * [2] Route to Link 1
- * [3] Route to Link 2
- * [19:16] Broadcast route
- * [0] Route to this node
- * [1] Route to Link 0
- * [2] Route to Link 1
- * [3] Route to Link 2
- */
+ /* Handle bugs in valid hypertransport frequency reporting */
+ uint16_t freq_cap;
+ uint32_t id;
+
+ freq_cap = pci_read_config16(dev, pos);
+ freq_cap &= ~(1 << HT_FREQ_VENDOR); /* Ignore Vendor HT frequencies */
+
+#if CONFIG_K8_HT_FREQ_1G_SUPPORT == 1
+ #if CONFIG_K8_REV_F_SUPPORT == 0
+ if (!is_cpu_pre_e0())
+ #endif
+ {
+ return freq_cap;
+ }
+#endif
- u32 ret=DEFAULT;
+ id = pci_read_config32(dev, 0);
- static const unsigned int rows_2p[2][2] = {
- { 0x00030101, 0x00010404 },
- { 0x00010404, 0x00030101 }
- };
+ /* AMD K8 Unsupported 1Ghz? */
+ if (id == (PCI_VENDOR_ID_AMD | (0x1100 << 16))) {
+ freq_cap &= ~(1 << HT_FREQ_1000Mhz);
+ }
- static const unsigned int rows_4p[4][4] = {
- { 0x00070101, 0x00010404, 0x00050202, 0x00010402 },
- { 0x00010808, 0x000b0101, 0x00010802, 0x00090202 },
- { 0x00090202, 0x00010802, 0x000b0101, 0x00010808 },
- { 0x00010402, 0x00050202, 0x00010404, 0x00070101 }
- };
+ return freq_cap;
+}
- if (!(node>=maxnodes || row>=maxnodes)) {
- if (maxnodes==2)
- ret=rows_2p[node][row];
- if (maxnodes==4)
- ret=rows_4p[node][row];
+static int optimize_connection(device_t node1, uint8_t link1, device_t node2, uint8_t link2)
+{
+ static const uint8_t link_width_to_pow2[]= { 3, 4, 0, 5, 1, 2, 0, 0 };
+ static const uint8_t pow2_to_link_width[] = { 0x7, 4, 5, 0, 1, 3 };
+ uint16_t freq_cap1, freq_cap2;
+ uint8_t width_cap1, width_cap2, width, old_width, ln_width1, ln_width2;
+ uint8_t freq, old_freq;
+ int needs_reset;
+ /* Set link width and frequency */
+
+ /* Initially assume everything is already optimized and I don't need a reset */
+ needs_reset = 0;
+
+ /* Get the frequency capabilities */
+ freq_cap1 = read_freq_cap(node1, link1 + PCI_HT_CAP_HOST_FREQ_CAP);
+ freq_cap2 = read_freq_cap(node2, link2 + PCI_HT_CAP_HOST_FREQ_CAP);
+
+ /* Calculate the highest possible frequency */
+ freq = log2(freq_cap1 & freq_cap2);
+
+ /* See if I am changing the link freqency */
+ old_freq = pci_read_config8(node1, link1 + PCI_HT_CAP_HOST_FREQ);
+ old_freq &= 0x0f;
+ needs_reset |= old_freq != freq;
+ old_freq = pci_read_config8(node2, link2 + PCI_HT_CAP_HOST_FREQ);
+ old_freq &= 0x0f;
+ needs_reset |= old_freq != freq;
+
+ /* Set the Calulcated link frequency */
+ pci_write_config8(node1, link1 + PCI_HT_CAP_HOST_FREQ, freq);
+ pci_write_config8(node2, link2 + PCI_HT_CAP_HOST_FREQ, freq);
+
+ /* Get the width capabilities */
+ width_cap1 = pci_read_config8(node1, link1 + PCI_HT_CAP_HOST_WIDTH);
+ width_cap2 = pci_read_config8(node2, link2 + PCI_HT_CAP_HOST_WIDTH);
+
+ /* Calculate node1's input width */
+ ln_width1 = link_width_to_pow2[width_cap1 & 7];
+ ln_width2 = link_width_to_pow2[(width_cap2 >> 4) & 7];
+ if (ln_width1 > ln_width2) {
+ ln_width1 = ln_width2;
}
+ width = pow2_to_link_width[ln_width1];
+ /* Calculate node1's output width */
+ ln_width1 = link_width_to_pow2[(width_cap1 >> 4) & 7];
+ ln_width2 = link_width_to_pow2[width_cap2 & 7];
+ if (ln_width1 > ln_width2) {
+ ln_width1 = ln_width2;
+ }
+ width |= pow2_to_link_width[ln_width1] << 4;
-#if 0
- printk_spew("generating entry n=%d, r=%d, max=%d - row=%x\n",
- node,row,maxnodes,ret);
+ /* See if I am changing node1's width */
+ old_width = pci_read_config8(node1, link1 + PCI_HT_CAP_HOST_WIDTH + 1);
+ old_width &= 0x77;
+ needs_reset |= old_width != width;
+
+ /* Set node1's widths */
+ pci_write_config8(node1, link1 + PCI_HT_CAP_HOST_WIDTH + 1, width);
+
+ // * Calculate node2's width */
+ width = ((width & 0x70) >> 4) | ((width & 0x7) << 4);
+
+ /* See if I am changing node2's width */
+ old_width = pci_read_config8(node2, link2 + PCI_HT_CAP_HOST_WIDTH + 1);
+ old_width &= 0x77;
+ needs_reset |= old_width != width;
+
+ /* Set node2's widths */
+ pci_write_config8(node2, link2 + PCI_HT_CAP_HOST_WIDTH + 1, width);
+
+ return needs_reset;
+}
+
+static uint8_t get_linkn_first(uint8_t byte)
+{
+ if(byte & 0x02) { byte = 0; }
+ else if(byte & 0x04) { byte = 1; }
+ else if(byte & 0x08) { byte = 2; }
+ return byte;
+}
+
+#if TRY_HIGH_FIRST == 1
+static uint8_t get_linkn_last(uint8_t byte)
+{
+ if(byte & 0x02) { byte &= 0x0f; byte |= 0x00; }
+ if(byte & 0x04) { byte &= 0x0f; byte |= 0x10; }
+ if(byte & 0x08) { byte &= 0x0f; byte |= 0x20; }
+ return byte>>4;
+}
#endif
-
- return ret;
+
+#if (CONFIG_MAX_PHYSICAL_CPUS > 2) || (CONFIG_MAX_PHYSICAL_CPUS_4_BUT_MORE_INSTALLED == 1)
+static uint8_t get_linkn_last_count(uint8_t byte)
+{
+ byte &= 0x0f;
+ if(byte & 0x02) { byte &= 0xcf; byte |= 0x00; byte+=0x40; }
+ if(byte & 0x04) { byte &= 0xcf; byte |= 0x10; byte+=0x40; }
+ if(byte & 0x08) { byte &= 0xcf; byte |= 0x20; byte+=0x40; }
+ return byte>>4;
}
+#endif
-static void fill_row(u8 node, u8 row, u32 value)
+static void setup_row_local(u8 source, u8 row) /* source will be 7 when it is for temp use*/
{
-#if 0
- print_debug("fill_row: pci_write_config32(");
- print_debug_hex32(NODE_HT(node));
- print_debug_char(',');
- print_debug_hex32(0x40 + (row << 2));
- print_debug_char(',');
- print_debug_hex32(value);
- print_debug(")\r\n");
-#endif
- pci_write_config32(NODE_HT(node), 0x40+(row<<2), value);
+ uint8_t linkn;
+ uint32_t val;
+ val = 1;
+ for(linkn = 0; linkn<3; linkn++) {
+ uint8_t regpos;
+ uint32_t reg;
+ regpos = 0x98 + 0x20 * linkn;
+ reg = pci_read_config32(NODE_HT(source), regpos);
+ if ((reg & 0x17) != 3) continue; /* it is not conherent or not connected*/
+ val |= 1<<(linkn+1);
+ }
+ val <<= 16;
+ val |= 0x0101;
+ fill_row(source,row, val);
}
-static void setup_row(u8 source, u8 dest, u8 cpus)
+static void setup_row_direct_x(u8 temp, u8 source, u8 dest, u8 linkn)
{
-#if 0
- printk_spew("setting up link from node %d to %d (%d cpus)\r\n",
- source, dest, cpus);
+ uint32_t val;
+ uint32_t val_s;
+ val = 1<<(linkn+1);
+ val |= 1<<(linkn+1+8); /*for direct connect response route should equal to request table*/
+
+ if(((source &1)!=(dest &1))
+#if CROSS_BAR_47_56
+ && ( (source<4)||(source>5) ) //(6,7) (7,6) should still be here
+ //(6,5) (7,4) should be here
#endif
+ ){
+ val |= (1<<16);
+ } else {
+ /*for CROSS_BAR_47_56 47, 56, should be here too
+ and for 47, 56, 57, 75, 46, 64 we need to substract another link to
+ 6, 7, 6, 6, 7, 7
+ */
+ val_s = get_row(temp, source);
+ val |= ((val_s>>16) - (1<<(linkn+1)))<<16;
+ }
- fill_row(source,dest,generate_row(source,dest,cpus));
+ fill_row(temp,dest, val );
}
-static void setup_temp_row(u8 source, u8 dest, u8 cpus)
+#if CROSS_BAR_47_56
+static void opt_broadcast_rt(u8 source, u8 dest, u8 kickout)
{
-#if 0
- printk_spew("setting up temp. link from node %d to %d (%d cpus)\r\n",
- source, dest, cpus);
+ uint32_t val;
+ val = get_row(source, dest);
+ val -= link_connection(source, kickout)<<16;
+ fill_row(source, dest, val);
+}
+
+static void opt_broadcast_rt_group(const u8 *conn, int num)
+{
+ int i;
+
+ for(i=0; i<num; i+=3) {
+ opt_broadcast_rt(conn[i], conn[i+1],conn[i+2]);
+ }
+}
+
+static void opt_broadcast_rt_plus(u8 source, u8 dest, u8 kickout)
+{
+ uint32_t val;
+ val = get_row(source, dest);
+ val += link_connection(source, kickout)<<16;
+ fill_row(source, dest, val);
+}
+
+static void opt_broadcast_rt_plus_group(const u8 *conn, int num)
+{
+ int i;
+
+ for(i=0; i<num; i+=3) {
+ opt_broadcast_rt_plus(conn[i], conn[i+1],conn[i+2]);
+ }
+}
#endif
- fill_row(source,7,generate_temp_row(source,dest,cpus));
+static void setup_row_direct(u8 source, u8 dest, u8 linkn)
+{
+ setup_row_direct_x(source, source, dest, linkn);
}
-static void setup_node(u8 node, u8 cpus)
+static void setup_remote_row_direct(u8 source, u8 dest, u8 linkn)
{
- u8 row;
- for(row=0; row<cpus; row++)
- setup_row(node, row, cpus);
+ setup_row_direct_x(7, source, dest, linkn);
}
-static void setup_remote_row(u8 source, u8 dest, u8 cpus)
+static void setup_temp_row(u8 source, u8 dest)
{
- fill_row(7, dest, generate_row(source, dest, cpus));
+ /* copy value from (source, dest) to (source,7) */
+ fill_row(source, 7, get_row(source, dest));
}
-static void setup_remote_node(u8 node, u8 cpus)
+static void setup_remote_node(u8 node)
{
- static const uint8_t pci_reg[] = {
- 0x44, 0x4c, 0x54, 0x5c, 0x64, 0x6c, 0x74, 0x7c,
+ static const uint8_t pci_reg[] = {
+ 0x44, 0x4c, 0x54, 0x5c, 0x64, 0x6c, 0x74, 0x7c,
0x40, 0x48, 0x50, 0x58, 0x60, 0x68, 0x70, 0x78,
0x84, 0x8c, 0x94, 0x9c, 0xa4, 0xac, 0xb4, 0xbc,
0x80, 0x88, 0x90, 0x98, 0xa0, 0xa8, 0xb0, 0xb8,
0xc0, 0xc8, 0xd0, 0xd8,
0xe0, 0xe4, 0xe8, 0xec,
};
- uint8_t row;
int i;
-#if 1
- print_debug("setup_remote_node\r\n");
-#endif
- for(row=0; row<cpus; row++)
- setup_remote_row(node, row, cpus);
+
+ print_spew("setup_remote_node: ");
/* copy the default resource map from node 0 */
- for(i = 0; i < sizeof(pci_reg)/sizeof(pci_reg[0]); i++) {
+ for(i = 0; i < ARRAY_SIZE(pci_reg); i++) {
uint32_t value;
uint8_t reg;
reg = pci_reg[i];
- print_debug("copying reg: ");
- print_debug_hex8(reg);
- print_debug("\r\n");
value = pci_read_config32(NODE_MP(0), reg);
pci_write_config32(NODE_MP(7), reg, value);
}
-#if 1
- print_debug("setup_remote_done\r\n");
-#endif
+ print_spew("done\n");
}
-#endif
+#endif /* CONFIG_MAX_PHYSICAL_CPUS > 1*/
-#if MAX_CPUS > 2
-static void setup_temp_node(u8 node, u8 cpus)
-{
- u8 row;
- for(row=0; row<cpus; row++)
- fill_row(7,row,generate_row(node,row,cpus));
-}
-#endif
-static u8 setup_uniprocessor(void)
+#if CONFIG_MAX_PHYSICAL_CPUS > 2
+#if !CROSS_BAR_47_56
+static void setup_row_indirect_x(u8 temp, u8 source, u8 dest)
+#else
+static void setup_row_indirect_x(u8 temp, u8 source, u8 dest, u8 gateway, u8 diff)
+#endif
{
- print_debug("Enabling UP settings\r\n");
- disable_probes();
- return 1;
-}
+ /*for indirect connection, we need to compute the val from val_s(source, source), and val_g(source, gateway) */
+ uint32_t val_s;
+ uint32_t val;
+#if !CROSS_BAR_47_56
+ u8 gateway;
+ u8 diff;
+ if(source<dest) {
+ gateway = source + 2;
+ } else {
+ gateway = source - 2;
+ }
+#endif
+ val_s = get_row(temp, source);
+ val = get_row(temp, gateway);
-#if MAX_CPUS > 1
-static u8 setup_smp(void)
-{
- u8 cpus=2;
+ val &= 0xffff;
+ val_s >>= 16;
+ val_s &= 0xfe;
- print_debug("Enabling SMP settings\r\n");
+#if !CROSS_BAR_47_56
+ diff = ((source&1)!=(dest &1));
+#endif
- setup_row(0,0,cpus);
- /* Setup and check a temporary connection to node 1 */
- setup_temp_row(0,1,cpus);
-
- if (!check_connection(0, 7, ACROSS)) { // Link: ACROSS
- print_debug("No connection to Node 1.\r\n");
- clear_temp_row(0); /* delete temp connection */
- setup_uniprocessor(); /* and get up working */
- return 1;
+ if(diff && (val_s!=(val&0xff)) ) { /* use another connect as response*/
+ val_s -= val & 0xff;
+#if (CONFIG_MAX_PHYSICAL_CPUS > 4) || (CONFIG_MAX_PHYSICAL_CPUS_4_BUT_MORE_INSTALLED == 1)
+ uint8_t byte;
+ /* Some node have two links left
+ * don't worry we only have (2, (3 as source need to handle
+ */
+ byte = val_s;
+ byte = get_linkn_last_count(byte);
+ if((byte>>2)>1) { /* make sure not the corner*/
+ if(source<dest) {
+ val_s-=link_connection(temp, source-2); /* -down*/
+ } else {
+#if CROSS_BAR_47_56
+ #if 0
+ if(source==7) {
+ val_s-=link_connection(temp, 6); // for 7,2 via 5
+ } else if (source==6){
+ val_s-=link_connection(temp, 7); // for 6,3 via 4
+ } else
+ #endif
+ if (source < gateway) { // for 5, 4 via 7
+ val_s-=link_connection(temp, source-2);
+ } else
+#endif
+ val_s-=link_connection(temp, source+2); /* -up*/
+ }
+ }
+#endif
+ val &= 0xff;
+ val |= (val_s<<8);
}
- /* We found 2 nodes so far */
- setup_node(0, cpus); /* Node 1 is there. Setup Node 0 correctly */
- setup_remote_node(1, cpus); /* Setup the routes on the remote node */
- enable_routing(7); /* Enable routing on Node 1 */
- rename_temp_node(1); /* Rename Node 7 to Node 1 */
-
- clear_temp_row(0); /* delete temporary connection */
-
-#if MAX_CPUS > 2
- cpus=4;
-
- /* Setup and check temporary connection from Node 0 to Node 2 */
- setup_temp_row(0,2,cpus);
-
- if (!check_connection(0, 7, UP)) { // Link: UP
- print_debug("No connection to Node 2.\r\n");
- clear_temp_row(0); /* delete temp connection */
- return 2;
+ if(diff) { /* cross rung?*/
+ val |= (1<<16);
}
-
- /* We found 3 nodes so far. Now setup a temporary
- * connection from node 0 to node 3 via node 1
- */
-
- setup_temp_row(0,1,cpus); /* temp. link between nodes 0 and 1 */
- setup_temp_row(1,3,cpus); /* temp. link between nodes 1 and 3 */
-
- if (!check_connection(1, 7, UP)) { // Link: UP
- print_debug("No connection to Node 3.\r\n");
- clear_temp_row(0); /* delete temp connection */
- clear_temp_row(1); /* delete temp connection */
- return 2;
+ else {
+ val_s = get_row(temp, source);
+ val |= ((val_s>>16) - link_connection(temp, gateway))<<16;
}
- /* We found 4 nodes so far. Now setup all nodes for 4p */
+ fill_row(temp, dest, val);
- setup_node(0, cpus); /* The first 2 nodes are configured */
- setup_node(1, cpus); /* already. Just configure them for 4p */
-
- setup_temp_row(0,2,cpus);
- setup_temp_node(2,cpus);
- enable_routing(7);
- rename_temp_node(2);
-
- setup_temp_row(0,1,cpus);
- setup_temp_row(1,3,cpus);
- setup_temp_node(3,cpus);
- enable_routing(7); /* enable routing on node 3 (temp.) */
- rename_temp_node(3);
-
- clear_temp_row(0);
- clear_temp_row(1);
- clear_temp_row(2);
- clear_temp_row(3);
+}
-#endif
- print_debug_hex32(cpus);
- print_debug(" nodes initialized.\r\n");
- return cpus;
+#if !CROSS_BAR_47_56
+static void setup_row_indirect(u8 source, u8 dest)
+{
+ setup_row_indirect_x(source, source, dest);
+}
+#else
+static void setup_row_indirect(u8 source, u8 dest, u8 gateway, u8 diff)
+{
+ setup_row_indirect_x(source, source, dest, gateway, diff);
}
#endif
-#if MAX_CPUS > 1
-static unsigned detect_mp_capabilities(unsigned cpus)
+static void setup_row_indirect_group(const u8 *conn, int num)
{
- unsigned node, row, mask;
- bool mp_cap=TRUE;
+ int i;
-#if 1
- print_debug("detect_mp_capabilities: ");
- print_debug_hex32(cpus);
- print_debug("\r\n");
+#if !CROSS_BAR_47_56
+ for(i=0; i<num; i+=2) {
+ setup_row_indirect(conn[i], conn[i+1]);
+#else
+ for(i=0; i<num; i+=4) {
+ setup_row_indirect(conn[i], conn[i+1],conn[i+2], conn[i+3]);
#endif
- if (cpus>2)
- mask=0x06; /* BigMPCap */
- else
- mask=0x02; /* MPCap */
- for (node=0; node<cpus; node++) {
- if ((pci_read_config32(NODE_MC(node), 0xe8) & mask)!=mask)
- mp_cap=FALSE;
}
-
- if (mp_cap)
- return cpus;
-
- /* one of our cpus is not mp capable */
-
- print_debug("One of the CPUs is not MP capable. Going back to UP\r\n");
-
- for (node=cpus; node>0; node--)
- for (row=cpus; row>0; row--)
- fill_row(NODE_HT(node-1), row-1, DEFAULT);
-
- return setup_uniprocessor();
}
+#if !CROSS_BAR_47_56
+static void setup_remote_row_indirect(u8 source, u8 dest)
+{
+ setup_row_indirect_x(7, source, dest);
+}
+#else
+static void setup_remote_row_indirect(u8 source, u8 dest, u8 gateway, u8 diff)
+{
+ setup_row_indirect_x(7, source, dest, gateway, diff);
+}
#endif
-/* this is a shrunken cpuid. */
-
-static unsigned int cpuid(unsigned int op)
+static void setup_remote_row_indirect_group(const u8 *conn, int num)
{
- unsigned int ret;
-
- asm volatile ( "cpuid" : "=a" (ret) : "a" (op));
+ int i;
- return ret;
+#if !CROSS_BAR_47_56
+ for(i=0; i<num; i+=2) {
+ setup_remote_row_indirect(conn[i], conn[i+1]);
+#else
+ for(i=0; i<num; i+=4) {
+ setup_remote_row_indirect(conn[i], conn[i+1],conn[i+2], conn[i+3]);
+#endif
+ }
}
-static void coherent_ht_finalize(unsigned cpus)
+#endif /*CONFIG_MAX_PHYSICAL_CPUS > 2*/
+
+
+static void setup_uniprocessor(void)
{
- int node;
- bool rev_a0;
-
+ print_spew("Enabling UP settings\n");
+#if CONFIG_LOGICAL_CPUS==1
+ unsigned tmp = (pci_read_config32(NODE_MC(0), 0xe8) >> 12) & 3;
+ if (tmp>0) return;
+#endif
+ disable_probes();
+}
+
+#if CONFIG_MAX_PHYSICAL_CPUS > 2
+static int optimize_connection_group(const u8 *opt_conn, int num)
+{
+ int needs_reset = 0;
+ int i;
+ for(i=0; i<num; i+=2) {
+ needs_reset = optimize_connection(
+ NODE_HT(opt_conn[i]), 0x80 + link_to_register(link_connection(opt_conn[i],opt_conn[i+1])),
+ NODE_HT(opt_conn[i+1]), 0x80 + link_to_register(link_connection(opt_conn[i+1],opt_conn[i])) );
+ }
+ return needs_reset;
+}
+#endif
+
+#if CONFIG_MAX_PHYSICAL_CPUS > 1
+static unsigned setup_smp2(void)
+{
+ unsigned nodes;
+ u8 byte;
+ uint32_t val;
+ nodes = 2;
+
+ setup_row_local(0, 0); /* it will update the broadcast RT*/
+
+ val = get_row(0,0);
+ byte = (val>>16) & 0xfe;
+ if(byte<0x2) { /* no coherent connection so get out.*/
+ nodes = 1;
+ return nodes;
+ }
+
+ /* Setup and check a temporary connection to node 1 */
+#if TRY_HIGH_FIRST == 1
+ byte = get_linkn_last(byte); /* Max Link to node1 */
+#else
+ byte = get_linkn_first(byte); /*Min Link to node1 --- according to AMD*/
+#endif
+ print_linkn("(0,1) link=", byte);
+ setup_row_direct(0,1, byte);
+ setup_temp_row(0, 1);
+
+ verify_connection(7);
+
+ /* We found 2 nodes so far */
+ val = pci_read_config32(NODE_HT(7), 0x6c);
+ byte = (val>>2) & 0x3; /*get default link on node7 to node0*/
+ print_linkn("(1,0) link=", byte);
+ setup_row_local(7,1);
+ setup_remote_row_direct(1, 0, byte);
+
+#if (CONFIG_MAX_PHYSICAL_CPUS > 4) || (CONFIG_MAX_PHYSICAL_CPUS_4_BUT_MORE_INSTALLED == 1)
+ val = get_row(7,1);
+ byte = (val>>16) & 0xfe;
+ byte = get_linkn_last_count(byte);
+ if((byte>>2)==3) { /* Oh! we need to treat it as node2. So use another link*/
+ val = get_row(0,0);
+ byte = (val>>16) & 0xfe;
+#if TRY_HIGH_FIRST == 1
+ byte = get_linkn_first(byte); /* Min link to Node1 */
+#else
+ byte = get_linkn_last(byte); /* Max link to Node1*/
+#endif
+ print_linkn("\t-->(0,1) link=", byte);
+ setup_row_direct(0,1, byte);
+ setup_temp_row(0, 1);
+
+ verify_connection(7);
+
+ /* We found 2 nodes so far */
+ val = pci_read_config32(NODE_HT(7), 0x6c);
+ byte = (val>>2) & 0x3; /* get default link on node7 to node0*/
+ print_linkn("\t-->(1,0) link=", byte);
+ setup_row_local(7,1);
+ setup_remote_row_direct(1, 0, byte);
+ }
+#endif
+
+ setup_remote_node(1); /* Setup the regs on the remote node */
+ rename_temp_node(1); /* Rename Node 7 to Node 1 */
+ enable_routing(1); /* Enable routing on Node 1 */
+#if 0
+ /*don't need and it is done by clear_dead_links */
+ clear_temp_row(0);
+#endif
+
+ return nodes;
+}
+#endif /*CONFIG_MAX_PHYSICAL_CPUS > 1 */
+
+#if CONFIG_MAX_PHYSICAL_CPUS > 2
+
+static unsigned setup_smp4(void)
+{
+ unsigned nodes;
+ u8 byte;
+ uint32_t val;
+
+ nodes=4;
+
+ /* Setup and check temporary connection from Node 0 to Node 2 */
+ val = get_row(0,0);
+ byte = ((val>>16) & 0xfe) - link_connection(0,1);
+ byte = get_linkn_last_count(byte);
+
+ if((byte>>2)==0) { /* We should have two coherent for 4p and above*/
+ nodes = 2;
+ return nodes;
+ }
+
+ byte &= 3; /* bit [3,2] is count-1*/
+ print_linkn("(0,2) link=", byte);
+ setup_row_direct(0, 2, byte); /*(0,2) direct link done*/
+
+ /* We found 3 nodes so far. Now setup a temporary
+ * connection from node 0 to node 3 via node 1
+ */
+ setup_temp_row(0,1); /* temp. link between nodes 0 and 1 */
+ /* here should setup_row_direct(1,3) at first, before that we should find the link in node 1 to 3*/
+ val = get_row(1,1);
+ byte = ((val>>16) & 0xfe) - link_connection(1,0);
+ byte = get_linkn_first(byte);
+ print_linkn("(1,3) link=", byte);
+ setup_row_direct(1,3,byte); /* (1, 3) direct link done*/
+
+ /* We found 4 nodes so far. Now setup all nodes for 4p */
+ // We need to make sure 0,2 and 1,3 link is set already
+#if !CROSS_BAR_47_56
+ static const u8 conn4_1[] = {
+ 0,3,
+ 1,2,
+ };
+#else
+ static const u8 conn4_1[] = {
+ 0,3,2,1,
+ 1,2,3,1,
+ };
+#endif
+
+ setup_row_indirect_group(conn4_1, ARRAY_SIZE(conn4_1));
+
+ setup_temp_row(0,2);
+ verify_connection(7);
+ val = pci_read_config32(NODE_HT(7), 0x6c);
+ byte = (val>>2) & 0x3; /* get default link on 7 to 0*/
+ print_linkn("(2,0) link=", byte);
+
+ setup_row_local(7,2);
+ setup_remote_row_direct(2, 0, byte); /* node 2 to node 0 direct link done */
+ setup_remote_node(2); /* Setup the regs on the remote node */
+
+ rename_temp_node(2); /* Rename Node 7 to Node 2 */
+ enable_routing(2); /* Enable routing on Node 2 */
+
+ setup_temp_row(0,1);
+ setup_temp_row(1,3);
+ verify_connection(7);
+
+ val = pci_read_config32(NODE_HT(7), 0x6c);
+ byte = (val>>2) & 0x3; /* get default link on 7 to 1*/
+ print_linkn("(3,1) link=", byte);
+
+ setup_row_local(7,3);
+ setup_remote_row_direct(3, 1, byte); /* node 3 to node 1 direct link done */
+ setup_remote_node(3); /* Setup the regs on the remote node */
+
+ /* We need to init link between 2, and 3 direct link */
+ val = get_row(2,2);
+ byte = ((val>>16) & 0xfe) - link_connection(2,0);
+ byte = get_linkn_last_count(byte);
+ print_linkn("(2,3) link=", byte & 3);
+
+ setup_row_direct(2,3, byte & 0x3);
+ setup_temp_row(0,2);
+ setup_temp_row(2,3);
+ verify_connection(7); /* to 3*/
+
+#if (CONFIG_MAX_PHYSICAL_CPUS > 4) || (CONFIG_MAX_PHYSICAL_CPUS_4_BUT_MORE_INSTALLED == 1)
+ /* We need to find out which link is to node3 */
+ if((byte>>2)==2) { /* one to node3, one to node0, one to node4*/
+ val = get_row(7,3);
+ if((val>>16) == 1) { /* that link is to node4, because via node1 it has been set, recompute it*/
+ val = get_row(2,2);
+ byte = ((val>>16) & 0xfe) - link_connection(2,0);
+ byte = get_linkn_first(byte);
+ print_linkn("\t-->(2,3) link=", byte);
+ setup_row_direct(2,3,byte);
+ setup_temp_row(2,3);
+ verify_connection(7); /* to 3*/
+ }
+ }
+#endif
+
+ val = pci_read_config32(NODE_HT(7), 0x6c);
+ byte = (val>>2) & 0x3; /* get default link on 7 to 2*/
+ print_linkn("(3,2) link=", byte);
+ setup_remote_row_direct(3,2, byte);
+
+#if (CONFIG_MAX_PHYSICAL_CPUS > 4) || (CONFIG_MAX_PHYSICAL_CPUS_4_BUT_MORE_INSTALLED == 1)
+ /* set link from 3 to 5 before enable it*/
+ val = get_row(7,3);
+ byte = ((val>>16) & 0xfe) - link_connection(7,2) - link_connection(7,1);
+ byte = get_linkn_last_count(byte);
+ if((byte>>2)==1) { /* We should have three coherent links on node 3 for 6p and above*/
+ byte &= 3; /*bit [3,2] is count-2*/
+ print_linkn("(3,5) link=", byte);
+ setup_remote_row_direct(3, 5, byte);
+ }
+
+ val = get_row(2,2);
+ byte = ((val>>16) & 0xfe) - link_connection(2,3) - link_connection(2,0);
+ byte = get_linkn_last_count(byte);
+
+ if((byte>>2)==1) { /* We should have three coherent link on node 2 for 6p and above*/
+ byte &= 3; /* bit [3,2] is count-2*/
+ print_linkn("(2,4) link=", byte);
+ setup_row_direct(2, 4, byte);
+ }
+#endif
+
+ //Beside 3, 1 is set, We need to make sure 3, 5 is set already in case has three link in 3
+#if !CROSS_BAR_47_56
+ static const u8 conn4_3[] = {
+ 3,0,
+ };
+#else
+ static const u8 conn4_3[] = {
+ 3,0,1,1,
+ };
+#endif
+ setup_remote_row_indirect_group(conn4_3, ARRAY_SIZE(conn4_3));
+
+/* ready to enable RT for Node 3 */
+ rename_temp_node(3);
+ enable_routing(3); /* enable routing on node 3 (temp.) */
+
+ // beside 2, 0 is set, We need to make sure 2, 4 link is set already in case has three link in 2
+#if !CROSS_BAR_47_56
+ static const u8 conn4_2[] = {
+ 2,1,
+ };
+#else
+ static const u8 conn4_2[] = {
+ 2,1,0,1,
+ };
+#endif
+ setup_row_indirect_group(conn4_2, ARRAY_SIZE(conn4_2));
+
+#if 0
+ /*We need to do sth to reverse work for setup_temp_row (0,1) (1,3) */
+ /* it will be done by clear_dead_links */
+ clear_temp_row(0);
+ clear_temp_row(1);
+#endif
+
+ return nodes;
+
+}
+
+#endif /* CONFIG_MAX_PHYSICAL_CPUS > 2 */
+
+#if CONFIG_MAX_PHYSICAL_CPUS > 4
+
+static unsigned setup_smp6(void)
+{
+ unsigned nodes;
+ u8 byte;
+ uint32_t val;
+
+ nodes=6;
+
+ /* Setup and check temporary connection from Node 0 to Node 4 through 2*/
+ val = get_row(2,2);
+ byte = ((val>>16) & 0xfe) - link_connection(2,3) - link_connection(2,0);
+ byte = get_linkn_last_count(byte);
+
+ if((byte>>2)==0) { /* We should have three coherent link on node 2 for 6p and above*/
+ nodes = 4;
+ return nodes;
+ }
+
+ /* Setup and check temporary connection from Node 0 to Node 5 through 1, 3*/
+ /* set link from 3 to 5 before enable it*/
+ val = get_row(3,3);
+ byte = ((val>>16) & 0xfe) - link_connection(3,2) - link_connection(3,1);
+ byte = get_linkn_last_count(byte);
+ if((byte>>2)==0) { /* We should have three coherent links on node 3 for 6p and above*/
+ nodes = 4;
+ return nodes;
+ }
+
+ /* We found 6 nodes so far. Now setup all nodes for 6p */
+#warning "FIXME we need to find out the correct gateway for 6p"
+ static const u8 conn6_1[] = {
+#if !CROSS_BAR_47_56
+ 0, 4,
+ 0, 5,
+ 1, 4,
+ 1, 5,
+ 2, 5,
+ 3, 4,
+#else
+ 0, 4, 2, 0,
+ 0, 5, 2, 1,
+ 1, 4, 3, 1,
+ 1, 5, 3, 0,
+ 2, 5, 3, 0,
+ 3, 4, 2, 0,
+#endif
+ };
+
+ setup_row_indirect_group(conn6_1, ARRAY_SIZE(conn6_1));
+
+ for(byte=0; byte<4; byte+=2) {
+ setup_temp_row(byte,byte+2);
+ }
+ verify_connection(7);
+ val = pci_read_config32(NODE_HT(7), 0x6c);
+ byte = (val>>2) & 0x3; /*get default link on 7 to 2*/
+ print_linkn("(4,2) link=", byte);
+
+ setup_row_local(7,4);
+ setup_remote_row_direct(4, 2, byte);
+ setup_remote_node(4); /* Setup the regs on the remote node */
+
+ /* Set indirect connection to 0, to 3 */
+ //we only need to set 4,0 here
+ static const u8 conn6_2[] = {
+#if !CROSS_BAR_47_56
+ 4, 0,
+#else
+ 4, 0, 2, 0,
+#endif
+ };
+
+ setup_remote_row_indirect_group(conn6_2, ARRAY_SIZE(conn6_2));
+
+ rename_temp_node(4);
+ enable_routing(4);
+
+ setup_temp_row(0,1);
+ for(byte=0; byte<4; byte+=2) {
+ setup_temp_row(byte+1,byte+3);
+ }
+ verify_connection(7);
+
+ val = pci_read_config32(NODE_HT(7), 0x6c);
+ byte = (val>>2) & 0x3; /* get default link on 7 to 3*/
+ print_linkn("(5,3) link=", byte);
+ setup_row_local(7,5);
+ setup_remote_row_direct(5, 3, byte);
+ setup_remote_node(5); /* Setup the regs on the remote node */
+
+#if !CROSS_BAR_47_56
+ /* We need to init link between 4, and 5 direct link */
+ val = get_row(4,4);
+ byte = ((val>>16) & 0xfe) - link_connection(4,2);
+ byte = get_linkn_last_count(byte);
+ print_linkn("(4,5) link=", byte & 3);
+
+ setup_row_direct(4,5, byte & 0x3);
+ setup_temp_row(0,2);
+ setup_temp_row(2,4);
+ setup_temp_row(4,5);
+ verify_connection(7); /* to 5*/
+
+#if CONFIG_MAX_PHYSICAL_CPUS > 6
+ /* We need to find out which link is to node5 */
+
+ if((byte>>2)==2) { /* one to node5, one to node2, one to node6*/
+ val = get_row(7,5);
+ if((val>>16) == 1) { /* that link is to node6, because via node 3 node 5 has been set*/
+ val = get_row(4,4);
+ byte = ((val>>16) & 0xfe) - link_connection(4,2);
+ byte = get_linkn_first(byte);
+ print_linkn("\t-->(4,5) link=", byte);
+ setup_row_direct(4,5,byte);
+ setup_temp_row(4,5);
+ verify_connection(7); /* to 5*/
+ }
+ }
+#endif
+
+ val = pci_read_config32(NODE_HT(7), 0x6c);
+ byte = (val>>2) & 0x3; /* get default link on 7 to 4*/
+ print_linkn("(5,4) link=", byte);
+ setup_remote_row_direct(5,4, byte);
+
+ //init 5, 7 here
+ val = get_row(7,5);
+ byte = ((val>>16) & 0xfe) - link_connection(7,4) - link_connection(7,3);
+ byte = get_linkn_last_count(byte);
+ if((byte>>2)==1) { /* We should have three coherent links on node 5 for 6p and above*/
+ byte &= 3; /*bit [3,2] is count-2*/
+ print_linkn("(5,7) link=", byte);
+ setup_remote_row_direct(5, 7, byte);
+ }
+
+ //init 4,6 here
+ val = get_row(4,4);
+ byte = ((val>>16) & 0xfe) - link_connection(4,5) - link_connection(4,2);
+ byte = get_linkn_last_count(byte);
+
+ if((byte>>2)==1) { /* We should have three coherent link on node 4 for 6p and above*/
+ byte &= 3; /* bit [3,2] is count-2*/
+ print_linkn("(4,6) link=", byte);
+ setup_row_direct(4, 6, byte);
+ }
+
+#endif
+
+ //We need to set 5,0 here only, We need to set up 5, 7 to make 5,0
+ /* Set indirect connection to 0, to 3 for indirect we will use clockwise routing */
+ static const u8 conn6_3[] = {
+#if !CROSS_BAR_47_56
+ 5, 0,
+#else
+ 5, 0, 3, 0,
+#endif
+ };
+
+ setup_remote_row_indirect_group(conn6_3, ARRAY_SIZE(conn6_3));
+
+/* ready to enable RT for 5 */
+ rename_temp_node(5);
+ enable_routing(5); /* enable routing on node 5 (temp.) */
+
+ static const u8 conn6_4[] = {
+#if !CROSS_BAR_47_56
+ 4, 1,
+ 4, 3,
+
+ 5, 2,
+ 5, 1,
+
+#else
+ 4, 1, 2, 0,
+ 4, 3, 2, 0,
+ 4, 5, 2, 0,
+
+ 5, 2, 3, 0,
+ 5, 1, 3, 0,
+ 5, 4, 3, 0,
+
+#endif
+ };
+
+ setup_row_indirect_group(conn6_4, ARRAY_SIZE(conn6_4));
+
+#if 0
+ /* We need to do sth about reverse about setup_temp_row (0,1), (2,4), (1, 3), (3,5)
+ * It will be done by clear_dead_links
+ */
+ for(byte=0; byte<4; byte++) {
+ clear_temp_row(byte);
+ }
+#endif
+
+ return nodes;
+
+}
+
+#endif /* CONFIG_MAX_PHYSICAL_CPUS > 4 */
+
+#if CONFIG_MAX_PHYSICAL_CPUS > 6
+
+static unsigned setup_smp8(void)
+{
+ unsigned nodes;
+ u8 byte;
+ uint32_t val;
+
+ nodes=8;
+
+ /* Setup and check temporary connection from Node 0 to Node 6 via 2 and 4 to 7 */
+ val = get_row(4,4);
+#if CROSS_BAR_47_56
+ byte = ((val>>16) & 0xfe) - link_connection(4,2);
+#else
+ byte = ((val>>16) & 0xfe) - link_connection(4,5) - link_connection(4,2);
+ byte = get_linkn_last_count(byte); /* Max link to 6*/
+ if((byte>>2)==0) { /* We should have two or three coherent links on node 4 for 8p*/
+ nodes = 6;
+ return nodes;
+ }
+#endif
+
+#if CROSS_BAR_47_56
+ byte = get_linkn_last_count(byte); /* Max link to 6*/
+ if((byte>>2)<2) { /* We should have two or three coherent links on node 4 for 8p*/
+ nodes = 6;
+ return nodes;
+ }
+#if TRY_HIGH_FIRST == 1
+ byte = ((val>>16) & 0xfe) - link_connection(4,2);
+ byte = get_linkn_first(byte); /*Min link to 6*/
+#else
+ byte &= 3; /* bit [3,2] is count-1 or 2*/
+#endif
+ print_linkn("(4,6) link=", byte);
+ setup_row_direct(4, 6, byte);
+#endif
+
+#if !CROSS_BAR_47_56
+ /* Setup and check temporary connection from Node 0 to Node 7 through 1, 3, 5*/
+ val = get_row(5,5);
+ byte = ((val>>16) & 0xfe) - link_connection(5,4) - link_connection(5,3);
+ byte = get_linkn_last_count(byte);
+ if((byte>>2)==0) { /* We should have three coherent links on node 5 for 6p and above*/
+ nodes = 6;
+ return nodes;
+ }
+#endif
+
+ /* We found 8 nodes so far. Now setup all nodes for 8p */
+ static const u8 conn8_1[] = {
+#if !CROSS_BAR_47_56
+ 0, 6,
+ /*0, 7,*/
+ 1, 6,
+ /*1, 7,*/
+ 2, 6,
+ /*2, 7,*/
+ 3, 6,
+ /*3, 7,*/
+ /*4, 7,*/
+ 5, 6,
+#else
+ 0, 6, 2, 0,
+ /*0, 7, 2, 0,*/
+ 1, 6, 3, 0,
+ /*1, 7, 3, 0,*/
+ 2, 6, 4, 0,
+ /*2, 7, 4, 0,*/
+ 3, 6, 5, 1,
+ /*3, 7, 5, 0,*/
+#endif
+ };
+
+ setup_row_indirect_group(conn8_1,ARRAY_SIZE(conn8_1));
+
+ for(byte=0; byte<6; byte+=2) {
+ setup_temp_row(byte,byte+2);
+ }
+ verify_connection(7);
+ val = pci_read_config32(NODE_HT(7), 0x6c);
+ byte = (val>>2) & 0x3; /* get default link on 7 to 4*/
+ print_linkn("(6,4) link=", byte);
+
+ setup_row_local(7,6);
+ setup_remote_row_direct(6, 4, byte);
+ setup_remote_node(6); /* Setup the regs on the remote node */
+ /* Set indirect connection to 0, to 3 */
+#warning "FIXME we need to find out the correct gateway for 8p"
+ static const u8 conn8_2[] = {
+#if !CROSS_BAR_47_56
+ 6, 0,
+#else
+ 6, 0, 4, 0,
+#endif
+ };
+
+ setup_remote_row_indirect_group(conn8_2, ARRAY_SIZE(conn8_2));
+
+#if CROSS_BAR_47_56
+ //init 5, 6 here
+ /* here init 5, 6 */
+ /* Setup and check temporary connection from Node 0 to Node 5 through 1, 3, 5*/
+ val = get_row(5,5);
+ byte = ((val>>16) & 0xfe) - link_connection(5,3);
+#if TRY_HIGH_FIRST == 1
+ byte = get_linkn_first(byte);
+#else
+ byte = get_linkn_last(byte);
+#endif
+ print_linkn("(5,6) link=", byte);
+ setup_row_direct(5, 6, byte);
+
+ setup_temp_row(0,1); /* temp. link between nodes 0 and 1 */
+ for(byte=0; byte<4; byte+=2) {
+ setup_temp_row(byte+1,byte+3);
+ }
+ setup_temp_row(5,6);
+
+ verify_connection(7);
+
+ val = get_row(7,6); // to chect it if it is node6 before renaming
+ if( (val>>16) == 1) { // it is real node 7 so swap it
+ /* We need to recompute link to 6 */
+ val = get_row(5,5);
+ byte = ((val>>16) & 0xfe) - link_connection(5,3);
+#if TRY_HIGH_FIRST == 1
+ byte = get_linkn_first(byte);
+#else
+ byte = get_linkn_last(byte);
+#endif
+ print_linkn("\t-->(5,6) link=", byte);
+ setup_row_direct(5, 6, byte);
+#if 0
+ setup_temp_row(0,1); /* temp. link between nodes 0 and 1 */
+ for(byte=0; byte<4; byte+=2) {
+ setup_temp_row(byte+1,byte+3);
+ }
+#endif
+ setup_temp_row(5,6);
+
+ verify_connection(7);
+ }
+ val = pci_read_config32(NODE_HT(7), 0x6c);
+ byte = (val>>2) & 0x3; /* get default link on 7 to 5*/
+ print_linkn("(6,5) link=", byte);
+ setup_remote_row_direct(6, 5, byte);
+ /*Till now 56, 65 done */
+#endif
+
+ rename_temp_node(6);
+ enable_routing(6);
+
+#if !CROSS_BAR_47_56
+ setup_temp_row(0,1);
+ for(byte=0; byte<6; byte+=2) {
+ setup_temp_row(byte+1,byte+3);
+ }
+
+ verify_connection(7);
+
+ val = pci_read_config32(NODE_HT(7), 0x6c);
+ byte = (val>>2) & 0x3; /* get default link on 7 to 5*/
+ print_linkn("(7,5) link=", byte);
+ setup_row_local(7,7);
+ setup_remote_row_direct(7, 5, byte);
+
+#else
+ val = get_row(4,4);
+ byte = ((val>>16) & 0xfe) - link_connection(4,2) - link_connection(4,6);
+ byte = get_linkn_first(byte);
+ print_linkn("(4,7) link=", byte);
+ setup_row_direct(4, 7, byte);
+
+ /* Setup and check temporary connection from Node 0 to Node 7 through 2, and 4*/
+ for(byte=0; byte<4; byte+=2) {
+ setup_temp_row(byte,byte+2);
+ }
+
+ verify_connection(7);
+
+ val = pci_read_config32(NODE_HT(7), 0x6c);
+ byte = (val>>2) & 0x3; /* get default link on 7 to 4*/
+ print_linkn("(7,4) link=", byte);
+ setup_row_local(7,7);
+ setup_remote_row_direct(7, 4, byte);
+ /* till now 4-7, 7-4 done. */
+#endif
+ setup_remote_node(7); /* Setup the regs on the remote node */
+
+#if CROSS_BAR_47_56
+ /* here init 5, 7 */
+ /* Setup and check temporary connection from Node 0 to Node 5 through 1, 3, 5*/
+ val = get_row(5,5);
+ byte = ((val>>16) & 0xfe) - link_connection(5,3) - link_connection(5,6);
+ byte = get_linkn_first(byte);
+ print_linkn("(5,7) link=", byte);
+ setup_row_direct(5, 7, byte);
+
+ setup_temp_row(0,1); /* temp. link between nodes 0 and 1 */
+ for(byte=0; byte<4; byte+=2) {
+ setup_temp_row(byte+1,byte+3);
+ }
+
+ verify_connection(7);
+
+ val = pci_read_config32(NODE_HT(7), 0x6c);
+ byte = (val>>2) & 0x3; /* get default link on 7 to 5*/
+ print_linkn("(7,5) link=", byte);
+ setup_remote_row_direct(7, 5, byte);
+ /*Till now 57, 75 done */
+
+#endif
+
+ /* We need to init link between 6, and 7 direct link */
+ val = get_row(6,6);
+#if !CROSS_BAR_47_56
+ byte = ((val>>16) & 0xfe) - link_connection(6,4);
+#else
+ byte = ((val>>16) & 0xfe) - link_connection(6,4) - link_connection(6,5);
+#endif
+ byte = get_linkn_first(byte);
+ print_linkn("(6,7) link=", byte);
+ setup_row_direct(6,7, byte);
+
+ val = get_row(7,7);
+#if !CROSS_BAR_47_56
+ byte = ((val>>16) & 0xfe) - link_connection(7,5);
+#else
+ byte = ((val>>16) & 0xfe) - link_connection(7,5) - link_connection(7,4);
+#endif
+ byte = get_linkn_first(byte);
+ print_linkn("(7,6) link=", byte);
+ setup_row_direct(7,6, byte);
+
+ /* Set indirect connection to 0, to 3 for indirect we will use clockwise routing */
+ static const u8 conn8_3[] = {
+#if !CROSS_BAR_47_56
+ 0, 7, /* restore it*/
+ 1, 7,
+ 2, 7,
+ 3, 7,
+ 4, 7,
+
+ 6, 1,
+ 6, 2,
+ 6, 3,
+ 6, 5,
+
+ 7, 0,
+ 7, 1,
+ 7, 2,
+ 7, 3,
+ 7, 4,
+#else
+
+
+ 4, 5, 6, 1,
+ 5, 4, 7, 1,
+
+ 6, 1, 5, 0, // or 4, 1
+ 6, 2, 4, 0,
+ 6, 3, 5, 0, // or 4, 1
+
+ 7, 0, 4, 0, // or 5, 1
+ 7, 1, 5, 0,
+ 7, 2, 4, 0, // or 5, 1
+ 7, 3, 5, 0,
+
+ 0, 7, 2, 0, /* restore it*/
+ 1, 7, 3, 0,
+ 2, 7, 4, 1,
+ 3, 7, 5, 0,
+
+ 2, 5, 4, 1, /* reset it */
+ 3, 4, 5, 1,
+
+ 4, 1, 2, 1, /* reset it */
+ 4, 3, 2, 1,
+
+ 5, 2, 3, 1, /* reset it */
+ 5, 0, 3, 1,
+
+#endif
+ };
+
+ setup_row_indirect_group(conn8_3, ARRAY_SIZE(conn8_3));
+
+#if CROSS_BAR_47_56
+ /* for 47, 56, 57, 75, 46, 64 we need to substract another link to
+ 6, 7, 6, 6, 7, 7 */
+ static const u8 conn8_4[] = {
+//direct
+ 4, 7, 6,
+ 5, 6, 7,
+ 5, 7, 6,
+ 7, 5, 6,
+ 4, 6, 7,
+ 6, 4, 7,
+
+//in direct
+ 0, 6, 1,
+ 0, 7, 1,
+
+ 1, 6, 0,
+ 1, 7, 0,
+
+ 2, 6, 3,
+// 2, 7, 3, +
+
+// 3, 6, 1, +
+ 3, 7, 2,
+
+ 6, 0, 7,
+ 6, 1, 7, // needed for via 5
+ 6, 1, 4, // ???
+ 6, 2, 7,
+ 6, 3, 7, // needed for via 5
+ 6, 3, 4, //???
+ 7, 0, 6, // needed for via 4
+ 7, 0, 5, //???
+ 7, 1, 6,
+ 7, 2, 6, // needed for via 4
+ 7, 2, 5, //???
+ 7, 3, 6,
+ };
+
+ opt_broadcast_rt_group(conn8_4, ARRAY_SIZE(conn8_4));
+
+ static const u8 conn8_5[] = {
+ 2, 7, 0,
+
+ 3, 6, 1,
+ };
+
+ opt_broadcast_rt_plus_group(conn8_5, ARRAY_SIZE(conn8_5));
+#endif
+
+
+
+/* ready to enable RT for Node 7 */
+ enable_routing(7); /* enable routing on node 7 (temp.) */
+
+ return nodes;
+}
+
+#endif /* CONFIG_MAX_PHYSICAL_CPUS > 6 */
+
+
+#if CONFIG_MAX_PHYSICAL_CPUS > 1
+
+static unsigned setup_smp(void)
+{
+ unsigned nodes;
+
+ print_spew("Enabling SMP settings\n");
+
+ nodes = setup_smp2();
+#if CONFIG_MAX_PHYSICAL_CPUS > 2
+ if(nodes == 2)
+ nodes = setup_smp4();
+#endif
+
+#if CONFIG_MAX_PHYSICAL_CPUS > 4
+ if(nodes == 4)
+ nodes = setup_smp6();
+#endif
+
+#if CONFIG_MAX_PHYSICAL_CPUS > 6
+ if(nodes == 6)
+ nodes = setup_smp8();
+#endif
+
+ printk(BIOS_DEBUG, "%02x nodes initialized.\n", nodes);
+
+ return nodes;
+}
+
+static unsigned verify_mp_capabilities(unsigned nodes)
+{
+ unsigned node, mask;
+
+ mask = 0x06; /* BigMPCap */
+
+ for (node=0; node<nodes; node++) {
+ mask &= pci_read_config32(NODE_MC(node), 0xe8);
+ }
+
+ switch(mask) {
+#if CONFIG_MAX_PHYSICAL_CPUS > 2
+ case 0x02: /* MPCap */
+ if(nodes > 2) {
+ print_err("Going back to DP\n");
+ return 2;
+ }
+ break;
+#endif
+ case 0x00: /* Non SMP */
+ if(nodes >1 ) {
+ print_err("Going back to UP\n");
+ return 1;
+ }
+ break;
+ }
+
+ return nodes;
+
+}
+
+
+static void clear_dead_routes(unsigned nodes)
+{
+ int last_row;
+ int node, row;
+#if CONFIG_MAX_PHYSICAL_CPUS == 8
+ if(nodes==8) return;/* don't touch (7,7)*/
+#endif
+ last_row = nodes;
+ if (nodes == 1) {
+ last_row = 0;
+ }
+ for(node = 7; node >= 0; node--) {
+ for(row = 7; row >= last_row; row--) {
+ fill_row(node, row, DEFAULT);
+ }
+ }
+
+ /* Update the local row */
+ for( node=0; node<nodes; node++) {
+ uint32_t val = 0;
+ for(row =0; row<nodes; row++) {
+ val |= get_row(node, row);
+ }
+ fill_row(node, node, (((val & 0xff) | ((val >> 8) & 0xff)) << 16) | 0x0101);
+ }
+}
+#endif /* CONFIG_MAX_PHYSICAL_CPUS > 1 */
+
+#if CONFIG_LOGICAL_CPUS==1
+static unsigned verify_dualcore(unsigned nodes)
+{
+ unsigned node, totalcpus, tmp;
+
+ totalcpus = 0;
+ for (node=0; node<nodes; node++) {
+ tmp = (pci_read_config32(NODE_MC(node), 0xe8) >> 12) & 3 ;
+ totalcpus += (tmp + 1);
+ }
+
+ return totalcpus;
+
+}
+#endif
+
+static void coherent_ht_finalize(unsigned nodes)
+{
+ unsigned node;
+#if CONFIG_K8_REV_F_SUPPORT == 0
+ int rev_a0;
+#endif
+#if CONFIG_LOGICAL_CPUS==1
+ unsigned total_cpus;
+
+ if (read_option(multi_core, 0) == 0) { /* multi_core */
+ total_cpus = verify_dualcore(nodes);
+ }
+ else {
+ total_cpus = nodes;
+ }
+#endif
+
/* set up cpu count and node count and enable Limit
* Config Space Range for all available CPUs.
* Also clear non coherent hypertransport bus range
* registers on Hammer A0 revision.
*/
-#if 1
- print_debug("coherent_ht_finalize\r\n");
+ print_spew("coherent_ht_finalize\n");
+#if CONFIG_K8_REV_F_SUPPORT == 0
+ rev_a0 = is_cpu_rev_a0();
#endif
- rev_a0=((cpuid(1)&0xffff)==0x0f10);
+ for (node = 0; node < nodes; node++) {
+ device_t dev;
+ uint32_t val;
+ dev = NODE_HT(node);
- for (node=0; node<cpus; node++) {
- u32 val;
- val=pci_read_config32(NODE_HT(node), 0x60);
+ /* Set the Total CPU and Node count in the system */
+ val = pci_read_config32(dev, 0x60);
val &= (~0x000F0070);
- val |= ((cpus-1)<<16)|((cpus-1)<<4);
- pci_write_config32(NODE_HT(node),0x60,val);
+#if CONFIG_LOGICAL_CPUS==1
+ val |= ((total_cpus-1)<<16)|((nodes-1)<<4);
+#else
+ val |= ((nodes-1)<<16)|((nodes-1)<<4);
+#endif
+ pci_write_config32(dev, 0x60, val);
+
+ /* Only respond to real cpu pci configuration cycles
+ * and optimize the HT settings
+ */
+ val=pci_read_config32(dev, HT_TRANSACTION_CONTROL);
+ val &= ~((HTTC_BUF_REL_PRI_MASK << HTTC_BUF_REL_PRI_SHIFT) |
+ (HTTC_MED_PRI_BYP_CNT_MASK << HTTC_MED_PRI_BYP_CNT_SHIFT) |
+ (HTTC_HI_PRI_BYP_CNT_MASK << HTTC_HI_PRI_BYP_CNT_SHIFT));
+ val |= HTTC_LIMIT_CLDT_CFG |
+ (HTTC_BUF_REL_PRI_8 << HTTC_BUF_REL_PRI_SHIFT) |
+ (3 << HTTC_MED_PRI_BYP_CNT_SHIFT) |
+ (3 << HTTC_HI_PRI_BYP_CNT_SHIFT);
+ pci_write_config32(dev, HT_TRANSACTION_CONTROL, val);
+
+#if CONFIG_K8_REV_F_SUPPORT == 0
+ if (rev_a0) {
+ pci_write_config32(dev, 0x94, 0);
+ pci_write_config32(dev, 0xb4, 0);
+ pci_write_config32(dev, 0xd4, 0);
+ }
+#endif
+ }
- val=pci_read_config32(NODE_HT(node), 0x68);
- val |= 0x00008000;
- pci_write_config32(NODE_HT(node),0x68,val);
+ print_spew("done\n");
+}
+
+static int apply_cpu_errata_fixes(unsigned nodes)
+{
+ unsigned node;
+ int needs_reset = 0;
+ for(node = 0; node < nodes; node++) {
+ device_t dev;
+ uint32_t cmd;
+ dev = NODE_MC(node);
+#if CONFIG_K8_REV_F_SUPPORT == 0
+ if (is_cpu_pre_c0()) {
+
+ /* Errata 66
+ * Limit the number of downstream posted requests to 1
+ */
+ cmd = pci_read_config32(dev, 0x70);
+ if ((cmd & (3 << 0)) != 2) {
+ cmd &= ~(3<<0);
+ cmd |= (2<<0);
+ pci_write_config32(dev, 0x70, cmd );
+ needs_reset = 1;
+ }
+ cmd = pci_read_config32(dev, 0x7c);
+ if ((cmd & (3 << 4)) != 0) {
+ cmd &= ~(3<<4);
+ cmd |= (0<<4);
+ pci_write_config32(dev, 0x7c, cmd );
+ needs_reset = 1;
+ }
+ /* Clock Power/Timing Low */
+ cmd = pci_read_config32(dev, 0xd4);
+ if (cmd != 0x000D0001) {
+ cmd = 0x000D0001;
+ pci_write_config32(dev, 0xd4, cmd);
+ needs_reset = 1; /* Needed? */
+ }
- if (rev_a0) {
- pci_write_config32(NODE_HT(node),0x94,0);
- pci_write_config32(NODE_HT(node),0xb4,0);
- pci_write_config32(NODE_HT(node),0xd4,0);
+ }
+ else if (is_cpu_pre_d0()) { // d0 later don't need it
+ uint32_t cmd_ref;
+ /* Errata 98
+ * Set Clk Ramp Hystersis to 7
+ * Clock Power/Timing Low
+ */
+ cmd_ref = 0x04e20707; /* Registered */
+ cmd = pci_read_config32(dev, 0xd4);
+ if(cmd != cmd_ref) {
+ pci_write_config32(dev, 0xd4, cmd_ref );
+ needs_reset = 1; /* Needed? */
+ }
+ }
+#endif
+
+
+#if CONFIG_K8_REV_F_SUPPORT == 0
+ /* I can't touch this msr on early buggy cpus, and cannot apply either 169 or 131 */
+ if (!is_cpu_pre_b3())
+#endif
+ {
+ /* Errata 169 */
+ /* We also need to set some bits in NB_CFG_MSR, which is handled in src/cpu/amd/model_fxx/ */
+ dev = NODE_HT(node);
+ cmd = pci_read_config32(dev, 0x68);
+ cmd &= ~(1 << 22);
+ cmd |= (1 << 21);
+ pci_write_config32(dev, 0x68, cmd);
}
}
+ return needs_reset;
+}
+
+static int optimize_link_read_pointers(unsigned nodes)
+{
+ unsigned node;
+ int needs_reset = 0;
+ for(node = 0; node < nodes; node++) {
+ device_t f0_dev, f3_dev;
+ uint32_t cmd_ref, cmd;
+ int link;
+ f0_dev = NODE_HT(node);
+ f3_dev = NODE_MC(node);
+ cmd_ref = cmd = pci_read_config32(f3_dev, 0xdc);
+ for(link = 0; link < 3; link++) {
+ uint32_t link_type;
+ unsigned reg;
+ /* This works on an Athlon64 because unimplemented links return 0 */
+ reg = 0x98 + (link * 0x20);
+ link_type = pci_read_config32(f0_dev, reg);
+ /* Only handle coherent links */
+ if ((link_type & (LinkConnected | InitComplete|NonCoherent)) ==
+ (LinkConnected|InitComplete))
+ {
+ cmd &= ~(0xff << (link *8));
+ cmd |= 0x25 << (link *8);
+ }
+ }
+ if (cmd != cmd_ref) {
+ pci_write_config32(f3_dev, 0xdc, cmd);
+ needs_reset = 1;
+ }
+ }
+ return needs_reset;
+}
+
+static inline unsigned get_nodes(void)
+{
+ return ((pci_read_config32(PCI_DEV(0, 0x18, 0), 0x60)>>4) & 7) + 1;
+}
+
+static int optimize_link_coherent_ht(void)
+{
+ int needs_reset = 0;
+
+ unsigned nodes;
+
+ nodes = get_nodes();
+
+#if CONFIG_MAX_PHYSICAL_CPUS > 1
+ if(nodes>1) {
+ needs_reset |= optimize_connection(
+ NODE_HT(0), 0x80 + link_to_register(link_connection(0,1)),
+ NODE_HT(1), 0x80 + link_to_register(link_connection(1,0)) );
+ }
+
+#if CONFIG_MAX_PHYSICAL_CPUS > 2
+ if(nodes>2) {
+ /* optimize physical connections - by LYH */
+ static const u8 opt_conn4[] = {
+ 0,2,
+ 1,3,
+ 2,3,
+ };
+ needs_reset |= optimize_connection_group(opt_conn4, ARRAY_SIZE(opt_conn4));
+ }
+#endif
+
+#if CONFIG_MAX_PHYSICAL_CPUS > 4
+ if(nodes>4) {
+ static const uint8_t opt_conn6[] ={
+ 2, 4,
+ 3, 5,
+ #if !CROSS_BAR_47_56
+ 4, 5,
+ #endif
+ };
+ needs_reset |= optimize_connection_group(opt_conn6, ARRAY_SIZE(opt_conn6));
+ }
+#endif
+
+#if CONFIG_MAX_PHYSICAL_CPUS > 6
+ if(nodes>6) {
+ static const uint8_t opt_conn8[] ={
+ 4, 6,
+ #if CROSS_BAR_47_56
+ 4, 7,
+ 5, 6,
+ #endif
+ 5, 7,
+ 6, 7,
+ };
+ needs_reset |= optimize_connection_group(opt_conn8, ARRAY_SIZE(opt_conn8));
+ }
+#endif
-#if 1
- print_debug("done\n");
#endif
+
+ needs_reset |= apply_cpu_errata_fixes(nodes);
+ needs_reset |= optimize_link_read_pointers(nodes);
+
+ return needs_reset;
}
+#if CONFIG_RAMINIT_SYSINFO
static void setup_coherent_ht_domain(void)
+#else
+static int setup_coherent_ht_domain(void)
+#endif
{
- unsigned cpus;
+ unsigned nodes;
+ nodes = 1;
enable_bsp_routing();
-#if MAX_CPUS == 1
- cpus=setup_uniprocessor();
-#else
- cpus=setup_smp();
- cpus=detect_mp_capabilities(cpus);
+#if CONFIG_MAX_PHYSICAL_CPUS > 1
+ nodes = setup_smp();
+ nodes = verify_mp_capabilities(nodes);
+ clear_dead_routes(nodes);
#endif
- coherent_ht_finalize(cpus);
-}
+ if (nodes == 1) {
+ setup_uniprocessor();
+ }
+ coherent_ht_finalize(nodes);
+
+#if !CONFIG_RAMINIT_SYSINFO
+ return optimize_link_coherent_ht();
#endif
+}
+
projects / coreboot.git / blobdiff