#include "option_table.h"
#include <console/console.h>
#include <cpu/amd/model_10xxx_rev.h>
-#include "southbridge/broadcom/bcm5785/bcm5785_early_smbus.c"
+#include "southbridge/broadcom/bcm5785/early_smbus.c"
#include "northbridge/amd/amdfam10/raminit.h"
#include "northbridge/amd/amdfam10/amdfam10.h"
#include <lib.h>
#include "lib/delay.c"
#include "cpu/x86/lapic/boot_cpu.c"
#include "northbridge/amd/amdfam10/reset_test.c"
-#include "superio/serverengines/pilot/pilot_early_serial.c"
-#include "superio/serverengines/pilot/pilot_early_init.c"
-#include "superio/nsc/pc87417/pc87417_early_serial.c"
+#include "superio/serverengines/pilot/early_serial.c"
+#include "superio/serverengines/pilot/early_init.c"
+#include "superio/nsc/pc87417/early_serial.c"
#include "cpu/x86/bist.h"
#include "northbridge/amd/amdfam10/debug.c"
#include "cpu/x86/mtrr/earlymtrr.c"
//#include "northbridge/amd/amdfam10/setup_resource_map.c"
-#include "southbridge/broadcom/bcm5785/bcm5785_early_setup.c"
+#include "southbridge/broadcom/bcm5785/early_setup.c"
#define SERIAL_DEV PNP_DEV(0x2e, PILOT_SP1)
#define RTC_DEV PNP_DEV(0x4e, PC87417_RTC)
#include "northbridge/amd/amdfam10/amdfam10.h"
#include "northbridge/amd/amdfam10/raminit_sysinfo_in_ram.c"
-#include "northbridge/amd/amdfam10/amdfam10_pci.c"
+#include "northbridge/amd/amdfam10/pci.c"
#include "cpu/amd/quadcore/quadcore.c"
#include "cpu/amd/car/post_cache_as_ram.c"
#include "cpu/amd/microcode/microcode.c"
+
+#if CONFIG_UPDATE_CPU_MICROCODE
#include "cpu/amd/model_10xxx/update_microcode.c"
+#endif
+
#include "cpu/amd/model_10xxx/init_cpus.c"
#include "northbridge/amd/amdfam10/early_ht.c"
struct sys_info *sysinfo = (struct sys_info *)(CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE);
u32 bsp_apicid = 0, val;
msr_t msr;
-
+
if (!cpu_init_detectedx && boot_cpu()) {
/* Nothing special needs to be done to find bus 0 */
/* Allow the HT devices to be found */
pilot_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
- uart_init();
+ console_init();
/* Halt if there was a built in self test failure */
report_bist_failure(bist);
- console_init();
pilot_early_init(SERIAL_DEV); //config port is being taken from SERIAL_DEV
val = cpuid_eax(1);
/* Setup sysinfo defaults */
set_sysinfo_in_ram(0);
+#if CONFIG_UPDATE_CPU_MICROCODE
update_microcode(val);
+#endif
post_code(0x33);
cpuSetAMDMSR();
post_cache_as_ram();
}
+
+/**
+ * BOOL AMD_CB_ManualBUIDSwapList(u8 Node, u8 Link, u8 **List)
+ * Description:
+ * This routine is called every time a non-coherent chain is processed.
+ * BUID assignment may be controlled explicitly on a non-coherent chain. Provide a
+ * swap list. The first part of the list controls the BUID assignment and the
+ * second part of the list provides the device to device linking. Device orientation
+ * can be detected automatically, or explicitly. See documentation for more details.
+ *
+ * Automatic non-coherent init assigns BUIDs starting at 1 and incrementing sequentially
+ * based on each device's unit count.
+ *
+ * Parameters:
+ * @param[in] u8 node = The node on which this chain is located
+ * @param[in] u8 link = The link on the host for this chain
+ * @param[out] u8** list = supply a pointer to a list
+ * @param[out] BOOL result = true to use a manual list
+ * false to initialize the link automatically
+ */
+BOOL AMD_CB_ManualBUIDSwapList (u8 node, u8 link, const u8 **List)
+{
+ static const u8 swaplist[] = { 0xFF, CONFIG_HT_CHAIN_UNITID_BASE, CONFIG_HT_CHAIN_END_UNITID_BASE, 0xFF };
+ /* If the BUID was adjusted in early_ht we need to do the manual override */
+ if ((CONFIG_HT_CHAIN_UNITID_BASE != 0) && (CONFIG_HT_CHAIN_END_UNITID_BASE != 0)) {
+ printk(BIOS_DEBUG, "AMD_CB_ManualBUIDSwapList()\n");
+ if ((node == 0) && (link == 0)) { /* BSP SB link */
+ *List = swaplist;
+ return 1;
+ }
+ }
+
+ return 0;
+}