Simplify a few code chunks, fix whitespace and indentation.

[coreboot.git] / src / mainboard / gigabyte / m57sli / romstage.c

diff --git a/src/mainboard/gigabyte/m57sli/romstage.c b/src/mainboard/gigabyte/m57sli/romstage.c
index c9599094abdd69a5d6686b329a85ebd19eff3a27..968e384021666f853fc742236a5f14e83f50f309 100644 (file)
--- a/src/mainboard/gigabyte/m57sli/romstage.c
+++ b/src/mainboard/gigabyte/m57sli/romstage.c
@@ -53,14 +53,8 @@
 #define SERIAL_DEV PNP_DEV(0x2e, IT8716F_SP1)
 #define GPIO_DEV PNP_DEV(0x2e, IT8716F_GPIO)
 
-static void memreset(int controllers, const struct mem_controller *ctrl)
-{
-}
-
-static inline void activate_spd_rom(const struct mem_controller *ctrl)
-{
-       /* nothing to do */
-}
+static void memreset(int controllers, const struct mem_controller *ctrl) { }
+static void activate_spd_rom(const struct mem_controller *ctrl) { }
 
 static inline int spd_read_byte(unsigned device, unsigned address)
 {
@@ -111,17 +105,16 @@ static void sio_setup(void)
 void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
 {
        static const uint16_t spd_addr [] = {
-                       // Node 0
-                       DIMM0, DIMM2, 0, 0,
-                       DIMM1, DIMM3, 0, 0,
-                       // Node 1
-                       DIMM4, DIMM6, 0, 0,
-                       DIMM5, DIMM7, 0, 0,
+               // Node 0
+               DIMM0, DIMM2, 0, 0,
+               DIMM1, DIMM3, 0, 0,
+               // Node 1
+               DIMM4, DIMM6, 0, 0,
+               DIMM5, DIMM7, 0, 0,
        };
 
         struct sys_info *sysinfo = (struct sys_info *)(CONFIG_DCACHE_RAM_BASE
                + CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE);
-
         int needs_reset = 0;
         unsigned bsp_apicid = 0;
        uint8_t tmp = 0;
@@ -129,18 +122,13 @@ void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
         if (!cpu_init_detectedx && boot_cpu()) {
                /* Nothing special needs to be done to find bus 0 */
                /* Allow the HT devices to be found */
-
                enumerate_ht_chain();
-
                sio_setup();
-
-               /* Setup the mcp55 */
                mcp55_enable_rom();
         }
 
-        if (bist == 0) {
+        if (bist == 0)
                bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);
-        }
 
        pnp_enter_ext_func_mode(SERIAL_DEV);
        /* The following line will set CLKIN to 24 MHz, external */
@@ -153,9 +141,6 @@ void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
                /* Set Serial Flash interface to 0x0820 */
                pnp_write_config(GPIO_DEV, 0x64, 0x08);
                pnp_write_config(GPIO_DEV, 0x65, 0x20);
-               /* We can get away with not resetting the logical device because
-                * it8716f_enable_dev(SERIAL_DEV, CONFIG_TTYS0_BASE) will do that.
-                */
        }
        it8716f_enable_dev(SERIAL_DEV, CONFIG_TTYS0_BASE);
        pnp_exit_ext_func_mode(SERIAL_DEV);
@@ -200,21 +185,15 @@ void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
                 msr_t msr;
                 msr=rdmsr(0xc0010042);
                 print_debug("begin msr fid, vid "); print_debug_hex32( msr.hi ); print_debug_hex32(msr.lo); print_debug("\n");
-
         }
-
         enable_fid_change();
-
         enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);
-
         init_fidvid_bsp(bsp_apicid);
-
         // show final fid and vid
         {
                 msr_t msr;
                 msr=rdmsr(0xc0010042);
                 print_debug("end   msr fid, vid "); print_debug_hex32( msr.hi ); print_debug_hex32(msr.lo); print_debug("\n");
-
         }
 #endif