* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*/
+/*
+ * This file initializes the CPU cores for voltage and frequency settings
+ * in the different power states.
+ */
+/*
-#if FAM10_SET_FIDVID == 1
+checklist (functions are in this file if no source file named)
+Fam10 Bios and Kernel Development Guide #31116, rev 3.48, April 22, 2010
+
+2.4.2.6 Requirements for p-states
+
+1.- F3x[84:80] According to table 100 : prep_fid_change
+
+2.- COF/VID :
+ 2.4.2.9.1 Steps 1,3-6 and warning for 2,7 if they apply
+ fixPsNbVidBeforeWR(...)
+ 2.4.2.9.1 Step 8 enable_fid_change
+ We do this for all nodes, I don't understand BKDG 100% on
+ whether this is or isn't meant by "on the local
+ processor". Must be OK.
+ 2.4.2.9.1 Steps 9-10 (repeat 1-7 and reset) romstage.c/init_cpus ?
+ 2.4.2.9.1 Steps 11-12 init_fidvid_stage2
+ 2.4.2.9.2 DualPlane PVI : Not supported, don't know how to detect,
+ needs specific circuitry.
+
+3.- 2.4.2.7 dualPlaneOnly(dev)
+
+4.- 2.4.2.8 applyBoostFIDOffset(dev)
+
+5.- enableNbPState1(dev)
+
+6.- 2.4.1.7
+ a) UpdateSinglePlaneNbVid()
+ b) setVSRamp(), called from prep_fid_change
+ c) prep_fid_change
+ d) improperly, for lack of voltage regulator details?,
+ F3xA0[PsiVidEn] in defaults.h
+ F3xA0[PsiVid] in init_cpus.c AMD_SetupPSIVID_d (before prep_fid_change)
+
+7.- TODO (Core Performance Boost is only available in revision E cpus, and we
+ don't seem to support those yet, at least they don't have any
+ constant in amddefs.h )
+
+8.- FIXME ? Transition to min Pstate according to 2.4.2.15.3 is required
+ by 2.4.2.6 after warm reset. But 2.4.2.15 states that it is not required
+ if the warm reset is issued by coreboot to update NbFid. So it is required
+ or not ? How can I tell who issued warm reset ?
+ Coreboot transitions to P0 instead, which is not recommended, and does
+ not follow 2.4.2.15.2 to do so.
+
+9.- TODO Requires information on current delivery capability
+ (depends on mainboard and maybe power supply ?). One might use a config
+ option with the maximum number of Ampers that the board can deliver to CPU.
+
+10.- [Multiprocessor] TODO 2.4.2.12
+ [Uniprocessor] FIXME ? We call setPStateMaxVal() in init_fidvid_stage2,
+ but not sure this is what is meant by "Determine the valid set of
+ P-states based on enabled P-states indicated
+ in MSRC001_00[68:64][PstateEn]" in 2.4.2.6-10
+
+11.- finalPstateChange() from init_fidvid_Stage2 (BKDG says just "may", anyway)
+
+12.- generate ACPI for p-states. FIXME
+ Needs more assesment. There's some kind of fixed support that
+ does not seem to depend on CPU revision or actual MSRC001_00[68:64]
+ as BKDG apparently requires.
+ http://www.coreboot.org/ACPI#CPU_Power_Management
+ At least for Tilapia board:
+ src/mainboard/<vendor>/<model>/acpi_tables.c write_acpi_tables(...) calls
+ acpi_add_ssdt_pstates(...)
+ in /src/northbridge/amd/amdfam10/amdfam10_acpi.c
+ which apparently copies them from static info in
+ src/mainboard/<vendor>/<model>/acpi/cpstate.asl
+
+"must also be completed"
+
+a.- PllLockTime set in ruleset in defaults.h
+ BKDG says set it "If MSRC001_00[68:64][CpuFid] is different between
+ any two enabled P-states", but since it does not say "only if"
+ I guess it is safe to do it always.
+
+b.- prep_fid_change(...)
-#define FAM10_SET_FIDVID_DEBUG 1
+ */
-// if we are tight of CAR stack, disable it
-#define FAM10_SET_FIDVID_STORE_AP_APICID_AT_FIRST 1
+#if CONFIG_SET_FIDVID
+
+#include <northbridge/amd/amdht/AsPsDefs.h>
static inline void print_debug_fv(const char *str, u32 val)
{
-#if FAM10_SET_FIDVID_DEBUG == 1
- printk_debug("%s%x\n", str, val);
+#if CONFIG_SET_FIDVID_DEBUG
+ printk(BIOS_DEBUG, "%s%x\n", str, val);
#endif
}
static inline void print_debug_fv_8(const char *str, u8 val)
{
-#if FAM10_SET_FIDVID_DEBUG == 1
- printk_debug("%s%02x\n", str, val);
+#if CONFIG_SET_FIDVID_DEBUG
+ printk(BIOS_DEBUG, "%s%02x\n", str, val);
#endif
}
static inline void print_debug_fv_64(const char *str, u32 val, u32 val2)
{
-#if FAM10_SET_FIDVID_DEBUG == 1
- printk_debug("%s%x%x\n", str, val, val2);
+#if CONFIG_SET_FIDVID_DEBUG
+ printk(BIOS_DEBUG, "%s%x%x\n", str, val, val2);
#endif
}
+struct fidvid_st {
+ u32 common_fid;
+};
static void enable_fid_change(u8 fid)
{
device_t dev;
int i;
- nodes = ((pci_read_config32(PCI_DEV(CBB, CDB, 0), 0x60) >> 4) & 7) + 1;
+ nodes = get_nodes();
- for(i = 0; i < nodes; i++) {
- dev = NODE_PCI(i,3);
+ for (i = 0; i < nodes; i++) {
+ dev = NODE_PCI(i, 3);
dword = pci_read_config32(dev, 0xd4);
dword &= ~0x1F;
dword |= (u32) fid & 0x1F;
dword |= 1 << 5; // enable
pci_write_config32(dev, 0xd4, dword);
- printk_debug("FID Change Node:%02x, F3xD4: %08x \n", i, dword);
+ printk(BIOS_DEBUG, "FID Change Node:%02x, F3xD4: %08x \n", i,
+ dword);
+ }
+}
+
+static void applyBoostFIDOffset( device_t dev ) {
+ // BKDG 2.4.2.8
+ // revision E only, but E is apparently not supported yet, therefore untested
+ if ((cpuid_edx(0x80000007) & CPB_MASK)
+ && ((cpuid_ecx(0x80000008) & NC_MASK) ==5) ) {
+ u32 core = get_node_core_id_x().coreid;
+ u32 asymetricBoostThisCore = ((pci_read_config32(dev, 0x10C) >> (core*2))) & 3;
+ msr_t msr = rdmsr(PS_REG_BASE);
+ u32 cpuFid = msr.lo & PS_CPU_FID_MASK;
+ cpuFid = cpuFid + asymetricBoostThisCore;
+ msr.lo &= ~PS_CPU_FID_MASK;
+ msr.lo |= cpuFid ;
+ wrmsr(PS_REG_BASE , msr);
+
+ }
+}
+
+static void enableNbPState1( device_t dev ) {
+ u32 cpuRev = mctGetLogicalCPUID(0xFF);
+ if (cpuRev & AMD_FAM10_C3) {
+ u32 nbPState = (pci_read_config32(dev, 0x1F0) & NB_PSTATE_MASK);
+ if ( nbPState){
+ u32 nbVid1 = (pci_read_config32(dev, 0x1F4) & NB_VID1_MASK) >> NB_VID1_SHIFT;
+ u32 i;
+ for (i = nbPState; i < NM_PS_REG; i++) {
+ msr_t msr = rdmsr(PS_REG_BASE + i);
+ if (msr.hi & PS_EN_MASK ) {
+ msr.hi |= NB_DID_M_ON;
+ msr.lo &= NB_VID_MASK_OFF;
+ msr.lo |= ( nbVid1 << NB_VID_POS);
+ wrmsr(PS_REG_BASE + i, msr);
+ }
+ }
+ }
+ }
+}
+
+static u8 setPStateMaxVal( device_t dev ) {
+ u8 i,maxpstate=0;
+ for (i = 0; i < NM_PS_REG; i++) {
+ msr_t msr = rdmsr(PS_REG_BASE + i);
+ if (msr.hi & PS_IDD_VALUE_MASK) {
+ msr.hi |= PS_EN_MASK ;
+ wrmsr(PS_REG_BASE + i, msr);
+ }
+ if (msr.hi | PS_EN_MASK) {
+ maxpstate = i;
+ }
+ }
+ //FIXME: CPTC2 and HTC_REG should get max per node, not per core ?
+ u32 reg = pci_read_config32(dev, CPTC2);
+ reg &= PS_MAX_VAL_MASK;
+ reg |= (maxpstate << PS_MAX_VAL_POS);
+ pci_write_config32(dev, CPTC2,reg);
+ return maxpstate;
+}
+
+static void dualPlaneOnly( device_t dev ) {
+ // BKDG 2.4.2.7
+
+ u32 cpuRev = mctGetLogicalCPUID(0xFF);
+ if ((mctGetProcessorPackageType() == AMD_PKGTYPE_AM3_2r2)
+ && (cpuRev & AMD_DR_Cx)) { // should be rev C or rev E but there's no constant for E
+ if ( (pci_read_config32(dev, 0x1FC) & DUAL_PLANE_ONLY_MASK)
+ && (pci_read_config32(dev, 0xA0) & PVI_MODE) ){
+ if (cpuid_edx(0x80000007) & CPB_MASK) {
+ // revision E only, but E is apparently not supported yet, therefore untested
+ msr_t minPstate = rdmsr(0xC0010065);
+ wrmsr(0xC0010065, rdmsr(0xC0010068) );
+ wrmsr(0xC0010068,minPstate);
+ } else {
+ msr_t msr;
+ msr.lo=0; msr.hi=0;
+ wrmsr(0xC0010064, rdmsr(0xC0010068) );
+ wrmsr(0xC0010068, msr );
+ }
+
+ //FIXME: CPTC2 and HTC_REG should get max per node, not per core ?
+ u8 maxpstate = setPStateMaxVal(dev);
+
+ u32 reg = pci_read_config32(dev, HTC_REG);
+ reg &= HTC_PS_LMT_MASK;
+ reg |= (maxpstate << PS_LIMIT_POS);
+ pci_write_config32(dev, HTC_REG,reg);
+
+ }
+ }
+}
+
+static int vidTo100uV(u8 vid)
+{// returns voltage corresponding to vid in tenths of mV, i.e. hundreds of uV
+ // BKDG #31116 rev 3.48 2.4.1.6
+ int voltage;
+ if (vid >= 0x7c) {
+ voltage = 0;
+ } else {
+ voltage = (15500 - (125*vid));
+ }
+ return voltage;
+}
+
+static void setVSRamp(device_t dev) {
+ /* BKDG r31116 2010-04-22 2.4.1.7 step b F3xD8[VSRampTime]
+ * If this field accepts 8 values between 10 and 500 us why
+ * does page 324 say "BIOS should set this field to 001b."
+ * (20 us) ?
+ * Shouldn't it depend on the voltage regulators, mainboard
+ * or something ?
+ */
+ u32 dword;
+ dword = pci_read_config32(dev, 0xd8);
+ dword &= VSRAMP_MASK;
+ dword |= VSRAMP_VALUE;
+ pci_write_config32(dev, 0xd8, dword);
+}
+
+static void recalculateVsSlamTimeSettingOnCorePre(device_t dev)
+{
+ u8 pviModeFlag;
+ u8 highVoltageVid, lowVoltageVid, bValue;
+ u16 minimumSlamTime;
+ u16 vSlamTimes[7] = { 1000, 2000, 3000, 4000, 6000, 10000, 20000 }; /* Reg settings scaled by 100 */
+ u32 dtemp;
+ msr_t msr;
+
+ /* This function calculates the VsSlamTime using the range of possible
+ * voltages instead of a hardcoded 200us.
+ * Note: his function is called only from prep_fid_change,
+ * and that from init_cpus.c finalize_node_setup()
+ * (after set AMD MSRs and init ht )
+ */
+
+ /* BKDG r31116 2010-04-22 2.4.1.7 step b F3xD8[VSSlamTime] */
+ /* Calculate Slam Time
+ * Vslam = (mobileCPU?0.2:0.4)us/mV * (Vp0 - (lowest out of Vpmin or Valt)) mV
+ * In our case, we will scale the values by 100 to avoid
+ * decimals.
+ */
+
+ /* Determine if this is a PVI or SVI system */
+ dtemp = pci_read_config32(dev, 0xA0);
+
+ if (dtemp & PVI_MODE)
+ pviModeFlag = 1;
+ else
+ pviModeFlag = 0;
+
+ /* Get P0's voltage */
+ /* MSRC001_00[68:64] are not programmed yet when called from
+ prep_fid_change, one might use F4x1[F0:E0] instead, but
+ theoretically MSRC001_00[68:64] are equal to them after
+ reset. */
+ msr = rdmsr(0xC0010064);
+ highVoltageVid = (u8) ((msr.lo >> PS_CPU_VID_SHFT) & 0x7F);
+ if (!(msr.hi & 0x80000000)) {
+ printk(BIOS_ERR,"P-state info in MSRC001_0064 is invalid !!!\n");
+ highVoltageVid = (u8) ((pci_read_config32(dev, 0x1E0)
+ >> PS_CPU_VID_SHFT) & 0x7F);
+ }
+
+ /* If SVI, we only care about CPU VID.
+ * If PVI, determine the higher voltage b/t NB and CPU
+ */
+ if (pviModeFlag) {
+ bValue = (u8) ((msr.lo >> PS_NB_VID_SHFT) & 0x7F);
+ if (highVoltageVid > bValue)
+ highVoltageVid = bValue;
+ }
+
+ /* Get PSmax's index */
+ msr = rdmsr(0xC0010061);
+ bValue = (u8) ((msr.lo >> PS_MAX_VAL_SHFT) & BIT_MASK_3);
+
+ /* Get PSmax's VID */
+ msr = rdmsr(0xC0010064 + bValue);
+ lowVoltageVid = (u8) ((msr.lo >> PS_CPU_VID_SHFT) & 0x7F);
+ if (!(msr.hi & 0x80000000)) {
+ printk(BIOS_ERR,"P-state info in MSR%8x is invalid !!!\n",0xC0010064 + bValue);
+ lowVoltageVid = (u8) ((pci_read_config32(dev, 0x1E0+(bValue*4))
+ >> PS_CPU_VID_SHFT) & 0x7F);
+ }
+
+ /* If SVI, we only care about CPU VID.
+ * If PVI, determine the higher voltage b/t NB and CPU
+ * BKDG 2.4.1.7 (a)
+ */
+ if (pviModeFlag) {
+ bValue = (u8) ((msr.lo >> PS_NB_VID_SHFT) & 0x7F);
+ if (lowVoltageVid > bValue)
+ lowVoltageVid = bValue;
+ }
+
+ /* Get AltVID */
+ dtemp = pci_read_config32(dev, 0xDC);
+ bValue = (u8) (dtemp & BIT_MASK_7);
+
+ /* Use the VID with the lowest voltage (higher VID) */
+ if (lowVoltageVid < bValue)
+ lowVoltageVid = bValue;
+
+ u8 mobileFlag = get_platform_type() & AMD_PTYPE_MOB;
+ minimumSlamTime = (mobileFlag?2:4) * (vidTo100uV(highVoltageVid) - vidTo100uV(lowVoltageVid)); /* * 0.01 us */
+
+
+ /* Now round up to nearest register setting.
+ * Note that if we don't find a value, we
+ * will fall through to a value of 7
+ */
+ for (bValue = 0; bValue < 7; bValue++) {
+ if (minimumSlamTime <= vSlamTimes[bValue])
+ break;
+ }
+
+ /* Apply the value */
+ dtemp = pci_read_config32(dev, 0xD8);
+ dtemp &= VSSLAM_MASK;
+ dtemp |= bValue;
+ pci_write_config32(dev, 0xd8, dtemp);
+}
+
+static u32 nb_clk_did(int node, u32 cpuRev,u8 procPkg) {
+ u8 link0isGen3 = 0;
+ u8 offset;
+ if (AMD_CpuFindCapability(node, 0, &offset)) {
+ link0isGen3 = (AMD_checkLinkType(node, 0, offset) & HTPHY_LINKTYPE_HT3 );
+ }
+ /* FIXME: NB_CLKDID should be 101b for AMD_DA_C2 in package
+ S1g3 in link Gen3 mode, but I don't know how to tell
+ package S1g3 from S1g4 */
+ if ((cpuRev & AMD_DA_C2) && (procPkg & AMD_PKGTYPE_S1gX)
+ && link0isGen3) {
+ return 5 ; /* divide clk by 128*/
+ } else {
+ return 4 ; /* divide clk by 16 */
+ }
+}
+
+
+static u32 power_up_down(int node, u8 procPkg) {
+ u32 dword=0;
+ /* from CPU rev guide #41322 rev 3.74 June 2010 Table 26 */
+ u8 singleLinkFlag = ((procPkg == AMD_PKGTYPE_AM3_2r2)
+ || (procPkg == AMD_PKGTYPE_S1gX)
+ || (procPkg == AMD_PKGTYPE_ASB2));
+
+ if (singleLinkFlag) {
+ /*
+ * PowerStepUp=01000b - 50nS
+ * PowerStepDown=01000b - 50ns
+ */
+ dword |= PW_STP_UP50 | PW_STP_DN50;
+ } else {
+ u32 dispRefModeEn = (pci_read_config32(NODE_PCI(node,0),0x68) >> 24) & 1;
+ u32 isocEn = 0;
+ int j;
+ for(j=0 ; (j<4) && (!isocEn) ; j++ ) {
+ u8 offset;
+ if (AMD_CpuFindCapability(node, j, &offset)) {
+ isocEn = (pci_read_config32(NODE_PCI(node,0),offset+4) >>12) & 1;
+ }
+ }
+
+ if (dispRefModeEn || isocEn) {
+ dword |= PW_STP_UP50 | PW_STP_DN50 ;
+ } else {
+ /* get number of cores for PowerStepUp & PowerStepDown in server
+ 1 core - 400nS - 0000b
+ 2 cores - 200nS - 0010b
+ 3 cores - 133nS -> 100nS - 0011b
+ 4 cores - 100nS - 0011b
+ */
+ switch (get_core_num_in_bsp(node)) {
+ case 0:
+ dword |= PW_STP_UP400 | PW_STP_DN400;
+ break;
+ case 1:
+ case 2:
+ dword |= PW_STP_UP200 | PW_STP_DN200;
+ break;
+ case 3:
+ dword |= PW_STP_UP100 | PW_STP_DN100;
+ break;
+ default:
+ dword |= PW_STP_UP100 | PW_STP_DN100;
+ break;
+ }
+ }
}
+ return dword;
+}
+
+static void config_clk_power_ctrl_reg0(int node, u32 cpuRev, u8 procPkg) {
+ device_t dev = NODE_PCI(node, 3);
+
+ /* Program fields in Clock Power/Control register0 (F3xD4) */
+
+ /* set F3xD4 Clock Power/Timing Control 0 Register
+ * NbClkDidApplyAll=1b
+ * NbClkDid=100b or 101b
+ * PowerStepUp= "platform dependent"
+ * PowerStepDown= "platform dependent"
+ * LinkPllLink=01b
+ * ClkRampHystCtl=HW default
+ * ClkRampHystSel=1111b
+ */
+ u32 dword= pci_read_config32(dev, 0xd4);
+ dword &= CPTC0_MASK;
+ dword |= NB_CLKDID_ALL | LNK_PLL_LOCK | CLK_RAMP_HYST_SEL_VAL;
+ dword |= (nb_clk_did(node,cpuRev,procPkg) << NB_CLKDID_SHIFT);
+
+ dword |= power_up_down(node, procPkg);
+
+ pci_write_config32(dev, 0xd4, dword);
+
+}
+
+static void config_power_ctrl_misc_reg(device_t dev,u32 cpuRev, u8 procPkg) {
+ /* check PVI/SVI */
+ u32 dword = pci_read_config32(dev, 0xA0);
+
+ /* BKDG r31116 2010-04-22 2.4.1.7 step b F3xA0[VSSlamVidMod] */
+ /* PllLockTime and PsiVidEn set in ruleset in defaults.h */
+ if (dword & PVI_MODE) { /* PVI */
+ /* set slamVidMode to 0 for PVI */
+ dword &= VID_SLAM_OFF ;
+ } else { /* SVI */
+ /* set slamVidMode to 1 for SVI */
+ dword |= VID_SLAM_ON;
+ }
+ /* set the rest of A0 since we're at it... */
+
+ if (cpuRev & (AMD_DA_Cx | AMD_RB_C3 )) {
+ dword |= NB_PSTATE_FORCE_ON;
+ } // else should we clear it ?
+
+
+ if ((procPkg == AMD_PKGTYPE_G34) || (procPkg == AMD_PKGTYPE_C32) ) {
+ dword |= BP_INS_TRI_EN_ON ;
+ }
+
+ /* TODO: look into C1E state and F3xA0[IdleExitEn]*/
+ #if CONFIG_SVI_HIGH_FREQ
+ if (cpuRev & AMD_FAM10_C3) {
+ dword |= SVI_HIGH_FREQ_ON;
+ }
+ #endif
+ pci_write_config32(dev, 0xA0, dword);
+}
+
+static void config_nb_syn_ptr_adj(device_t dev, u32 cpuRev) {
+ /* Note the following settings are additional from the ported
+ * function setFidVidRegs()
+ */
+ /* adjust FIFO between nb and core clocks to max allowed
+ values (min latency) */
+ u32 nbPstate = pci_read_config32(dev,0x1f0) & NB_PSTATE_MASK;
+ u8 nbSynPtrAdj;
+ if ((cpuRev & (AMD_DR_Bx|AMD_DA_Cx) )
+ || ( (cpuRev & AMD_RB_C3) && (nbPstate!=0))) {
+ nbSynPtrAdj = 5;
+ } else {
+ nbSynPtrAdj = 6;
+ }
+
+ u32 dword = pci_read_config32(dev, 0xDc);
+ dword &= ~ NB_SYN_PTR_ADJ_MASK;
+ dword |= nbSynPtrAdj << NB_SYN_PTR_ADJ_POS;
+ /* NbsynPtrAdj set to 5 or 6 per BKDG (needs reset) */
+ pci_write_config32(dev, 0xdc, dword);
+}
+
+static void config_acpi_pwr_state_ctrl_regs(device_t dev, u32 cpuRev, u8 procPkg) {
+ /* step 1, chapter 2.4.2.6 of AMD Fam 10 BKDG #31116 Rev 3.48 22.4.2010 */
+ u32 dword;
+ u32 c1= 1;
+ if (cpuRev & (AMD_DR_Bx)) {
+ // will coreboot ever enable cache scrubbing ?
+ // if it does, will it be enough to check the current state
+ // or should we configure for what we'll set up later ?
+ dword = pci_read_config32(dev, 0x58);
+ u32 scrubbingCache = dword &
+ ( (0x1F << 16) // DCacheScrub
+ | (0x1F << 8) ); // L2Scrub
+ if (scrubbingCache) {
+ c1 = 0x80;
+ } else {
+ c1 = 0xA0;
+ }
+ } else { // rev C or later
+ // same doubt as cache scrubbing: ok to check current state ?
+ dword = pci_read_config32(dev, 0xDC);
+ u32 cacheFlushOnHalt = dword & (7 << 16);
+ if (!cacheFlushOnHalt) {
+ c1 = 0x80;
+ }
+ }
+ dword = (c1 << 24) | (0xE641E6);
+ pci_write_config32(dev, 0x84, dword);
+
+
+ /* FIXME: BKDG Table 100 says if the link is at a Gen1
+frequency and the chipset does not support a 10us minimum LDTSTOP
+assertion time, then { If ASB2 && SVI then smaf001 = F6h else
+smaf001=87h. } else ... I hardly know what it means or how to check
+it from here, so I bluntly assume it is false and code here the else,
+which is easier */
+
+ u32 smaf001 = 0xE6;
+ if (cpuRev & AMD_DR_Bx ) {
+ smaf001 = 0xA6;
+ } else {
+ #if CONFIG_SVI_HIGH_FREQ
+ if (cpuRev & (AMD_RB_C3 | AMD_DA_C3)) {
+ smaf001 = 0xF6;
+ }
+ #endif
+ }
+ u32 fidvidChange = 0;
+ if (((cpuRev & AMD_DA_Cx) && (procPkg & AMD_PKGTYPE_S1gX))
+ || (cpuRev & AMD_RB_C3) ) {
+ fidvidChange=0x0B;
+ }
+ dword = (0xE6 << 24) | (fidvidChange << 16)
+ | (smaf001 << 8) | 0x81;
+ pci_write_config32(dev, 0x80, dword);
}
static void prep_fid_change(void)
{
- u32 dword;
+ u32 dword;
u32 nodes;
device_t dev;
int i;
/* This needs to be run before any Pstate changes are requested */
- nodes = ((pci_read_config32(PCI_DEV(CBB, CDB, 0), 0x60) >> 4) & 7) + 1;
+ nodes = get_nodes();
- for(i = 0; i < nodes; i++) {
- printk_debug("Node:%02x \n", i);
- dev = NODE_PCI(i,3);
+ for (i = 0; i < nodes; i++) {
+ printk(BIOS_DEBUG, "Prep FID/VID Node:%02x \n", i);
+ dev = NODE_PCI(i, 3);
+ u32 cpuRev = mctGetLogicalCPUID(0xFF) ;
+ u8 procPkg = mctGetProcessorPackageType();
- dword = pci_read_config32(dev, 0xa0);
- dword &= ~(1<<29);
- dword |= ((~dword >> 8) & 1) << 29; // SlamVidMode is the inverse to the PviMode
- dword |= PLLLOCK_DFT_L; /* Force per BKDG */
- pci_write_config32(dev, 0xa0, dword);
- printk_debug(" F3xA0: %08x \n", dword);
+ setVSRamp(dev);
+ /* BKDG r31116 2010-04-22 2.4.1.7 step b F3xD8[VSSlamTime] */
+ /* Figure out the value for VsSlamTime and program it */
+ recalculateVsSlamTimeSettingOnCorePre(dev);
- dword = pci_read_config32(dev, 0xd8);
- dword &= ~0x77;
- dword |= (1<<4) | 6; // VSRampTime, and VSSlamTime
- dword |= 3 << 24; // ReConDel set to 3 per BKDG
- pci_write_config32(dev, 0xd8, dword);
- printk_debug(" F3xD8: %08x \n", dword);
+ config_clk_power_ctrl_reg0(i,cpuRev,procPkg);
- dword = pci_read_config32(dev, 0xd4);
- dword &= 0x1F;
- dword |= 0xC331AF00; // per BKDG
- pci_write_config32(dev, 0xd4, dword);
- printk_debug(" F3xD4: %08x \n", dword);
+ config_power_ctrl_misc_reg(dev,cpuRev,procPkg);
+ config_nb_syn_ptr_adj(dev,cpuRev);
- dword = pci_read_config32(dev, 0xdc);
- dword |= 0x5 << 12; // NbsynPtrAdj set to 0x5 per BKDG (needs reset)
- pci_write_config32(dev, 0xdc, dword);
- printk_debug(" F3xDC: %08x \n", dword);
+ config_acpi_pwr_state_ctrl_regs(dev,cpuRev,procPkg);
- // Rev B settings - FIXME: support other revs.
- dword = 0xA0E641E6;
- pci_write_config32(dev, 0x84, dword);
- printk_debug(" F3x84: %08x \n", dword);
+ dword = pci_read_config32(dev, 0x80);
+ printk(BIOS_DEBUG, " F3x80: %08x \n", dword);
+ dword = pci_read_config32(dev, 0x84);
+ printk(BIOS_DEBUG, " F3x84: %08x \n", dword);
+ dword = pci_read_config32(dev, 0xD4);
+ printk(BIOS_DEBUG, " F3xD4: %08x \n", dword);
+ dword = pci_read_config32(dev, 0xD8);
+ printk(BIOS_DEBUG, " F3xD8: %08x \n", dword);
+ dword = pci_read_config32(dev, 0xDC);
+ printk(BIOS_DEBUG, " F3xDC: %08x \n", dword);
- dword = 0xE600A681;
- pci_write_config32(dev, 0x80, dword);
- printk_debug(" F3x80: %08x \n", dword);
}
}
+static void waitCurrentPstate(u32 target_pstate){
+ msr_t initial_msr = rdmsr(TSC_MSR);
+ msr_t pstate_msr = rdmsr(CUR_PSTATE_MSR);
+ msr_t tsc_msr;
+ u8 timedout ;
+
+ /* paranoia ? I fear when we run fixPsNbVidBeforeWR we can enter a
+ * P1 that is a copy of P0, therefore has the same NB DID but the
+ * TSC will count twice per tick, so we have to wait for twice the
+ * count to achieve the desired timeout. But I'm likely to
+ * misunderstand this...
+ */
+ u32 corrected_timeout = ( (pstate_msr.lo==1)
+ && (!(rdmsr(0xC0010065).lo & NB_DID_M_ON)) ) ?
+ WAIT_PSTATE_TIMEOUT*2 : WAIT_PSTATE_TIMEOUT ;
+ msr_t timeout;
+
+ timeout.lo = initial_msr.lo + corrected_timeout ;
+ timeout.hi = initial_msr.hi;
+ if ( (((u32)0xffffffff) - initial_msr.lo) < corrected_timeout ) {
+ timeout.hi++;
+ }
+
+ // assuming TSC ticks at 1.25 ns per tick (800 MHz)
+ do {
+ pstate_msr = rdmsr(CUR_PSTATE_MSR);
+ tsc_msr = rdmsr(TSC_MSR);
+ timedout = (tsc_msr.hi > timeout.hi)
+ || ((tsc_msr.hi == timeout.hi) && (tsc_msr.lo > timeout.lo ));
+ } while ( (pstate_msr.lo != target_pstate) && (! timedout) ) ;
+
+ if (pstate_msr.lo != target_pstate) {
+ msr_t limit_msr = rdmsr(0xc0010061);
+ printk(BIOS_ERR, "*** Time out waiting for P-state %01x. Current P-state %01x P-state current limit MSRC001_0061=%02x\n", target_pstate, pstate_msr.lo, limit_msr.lo);
+
+ do { // should we just go on instead ?
+ pstate_msr = rdmsr(CUR_PSTATE_MSR);
+ } while ( pstate_msr.lo != target_pstate ) ;
+ }
+}
-#include "fidvid_common.c"
+static void set_pstate(u32 nonBoostedPState) {
+ msr_t msr;
+ // Transition P0 for calling core.
+ msr = rdmsr(0xC0010062);
+ msr.lo = nonBoostedPState;
+ wrmsr(0xC0010062, msr);
-static void init_fidvid_ap(u32 bsp_apicid, u32 apicid, u32 nodeid, u32 coreid)
-{
+ /* Wait for P0 to set. */
+ waitCurrentPstate(nonBoostedPState);
+}
- msr_t msr;
- device_t dev;
- u8 vid_max;
- u8 fid_max;
- u8 startup_pstate;
- u8 nb_cof_vid_update;
- u8 pvimode;
- u32 reg1fc;
- u32 dword;
- u32 send;
- printk_debug("FIDVID on AP: %02x\n", apicid);
- /* Only support single plane system at this time. */
- /* Steps 1-6 of BIOS NB COF and VID Configuration
- * for Single-Plane PVI Systems
- */
- dev = NODE_PCI(nodeid,3);
- reg1fc = pci_read_config32(dev, 0x1FC);
- nb_cof_vid_update = reg1fc & 1;
- if (nb_cof_vid_update) {
- /* Get fused settings */
- dword = pci_read_config32(dev, 0xa0);
- pvimode = (dword >> 8) & 1;
-
- vid_max = (reg1fc >> 7) & 0x7F; // per node
- fid_max = (reg1fc >> 2) & 0x1F; // per system
-
- if (pvimode) {
- /* FIXME: support daul plane mode */
- die("PVImode not supported\n");
- /* fidmax = vidmax - (reg1fc >> 17) & 0x1F;
- fidmax = fidmax + (reg1fc >> 14) & 0x03;
- */
- }
- } else {
- /* Use current values */
- msr = rdmsr(0xc0010071);
- fid_max = ((msr.hi >> (59-32)) & 0x1f); //max nb fid
- vid_max = ((msr.hi >> (35-32)) & 0x7f); //max vid
- }
+static void UpdateSinglePlaneNbVid(void)
+{
+ u32 nbVid, cpuVid;
+ u8 i;
+ msr_t msr;
- /* Note this is the single plane setup. Need to add dual plane path */
- msr = rdmsr(0xc0010071);
- startup_pstate = (msr.hi >> (32-32)) & 0x07;
+ /* copy higher voltage (lower VID) of NBVID & CPUVID to both */
+ for (i = 0; i < 5; i++) {
+ msr = rdmsr(PS_REG_BASE + i);
+ nbVid = (msr.lo & PS_CPU_VID_M_ON) >> PS_CPU_VID_SHFT;
+ cpuVid = (msr.lo & PS_NB_VID_M_ON) >> PS_NB_VID_SHFT;
+ if (nbVid != cpuVid) {
+ if (nbVid > cpuVid)
+ nbVid = cpuVid;
- /* Copy startup pstate to P1 and P0 MSRs. Set the maxvid for this node in P0.
- Then transition to P1 for corex and P0 for core0. */
+ msr.lo = msr.lo & PS_BOTH_VID_OFF;
+ msr.lo = msr.lo | (u32) ((nbVid) << PS_NB_VID_SHFT);
+ msr.lo = msr.lo | (u32) ((nbVid) << PS_CPU_VID_SHFT);
+ wrmsr(PS_REG_BASE + i, msr);
+ }
+ }
+}
+
+static void fixPsNbVidBeforeWR(u32 newNbVid, u32 coreid, u32 dev, u8 pviMode)
+ {
+ msr_t msr;
+ u8 startup_pstate;
+
+ /* This function sets NbVid before the warm reset.
+ * Get StartupPstate from MSRC001_0071.
+ * Read Pstate register pointed by [StartupPstate].
+ * and copy its content to P0 and P1 registers.
+ * Copy newNbVid to P0[NbVid].
+ * transition to P1 on all cores,
+ * then transition to P0 on core 0.
+ * Wait for MSRC001_0063[CurPstate] = 000b on core 0.
+ * see BKDG rev 3.48 2.4.2.9.1 BIOS NB COF and VID Configuration
+ * for SVI and Single-Plane PVI Systems
+ */
+
+ msr = rdmsr(0xc0010071);
+ startup_pstate = (msr.hi >> (32 - 32)) & 0x07;
+
+ /* Copy startup pstate to P1 and P0 MSRs. Set the maxvid for
+ * this node in P0. Then transition to P1 for corex and P0
+ * for core0. These setting will be cleared by the warm reset
+ */
msr = rdmsr(0xC0010064 + startup_pstate);
wrmsr(0xC0010065, msr);
wrmsr(0xC0010064, msr);
+ /* missing step 2 from BDKG , F3xDC[PstateMaxVal] =
+ * max(1,F3xDC[PstateMaxVal] ) because it would take
+ * synchronization between cores and we don't think
+ * PstatMaxVal is going to be 0 on cold reset anyway ?
+ */
+ if ( ! (pci_read_config32(dev, 0xDC) & (~ PS_MAX_VAL_MASK)) ) {
+ printk(BIOS_ERR,"F3xDC[PstateMaxVal] is zero. Northbridge voltage setting will fail. fixPsNbVidBeforeWR in fidvid.c needs fixing. See AMD # 31116 rev 3.48 BKDG 2.4.2.9.1 \n");
+ };
+
msr.lo &= ~0xFE000000; // clear nbvid
- msr.lo |= vid_max << 25;
+ msr.lo |= (newNbVid << 25);
wrmsr(0xC0010064, msr);
- // Transition to P1 for all APs and P0 for core0.
- msr = rdmsr(0xC0010062);
- msr.lo = (msr.lo & ~0x07) | 1;
- wrmsr(0xC0010062, msr);
+ if (pviMode) { /* single plane*/
+ UpdateSinglePlaneNbVid();
+ }
- // Wait for P1 to set.
- do {
- msr = rdmsr(0xC0010063);
- } while (msr.lo != 1);
+ // Transition to P1 for all APs and P0 for core0.
+ set_pstate(1);
if (coreid == 0) {
- msr.lo = msr.lo & ~0x07;
- wrmsr(0xC0010062, msr);
- // Wait for P0 to set.
- do {
- msr = rdmsr(0xC0010063);
- } while (msr.lo != 0);
+ set_pstate(0);
+ }
+
+ /* missing step 7 (restore PstateMax to 0 if needed) because
+ * we skipped step 2
+ */
+
+}
+
+static u32 needs_NB_COF_VID_update(void)
+{
+ u8 nb_cof_vid_update;
+ u8 nodes;
+ u8 i;
+
+ /* If any node has nb_cof_vid_update set all nodes need an update. */
+ nodes = get_nodes();
+ nb_cof_vid_update = 0;
+ for (i = 0; i < nodes; i++) {
+ u32 cpuRev = mctGetLogicalCPUID(i) ;
+ u32 nbCofVidUpdateDefined = (cpuRev & (AMD_FAM10_LT_D));
+ if (nbCofVidUpdateDefined
+ && (pci_read_config32(NODE_PCI(i, 3), 0x1FC)
+ & NB_COF_VID_UPDATE_MASK)) {
+ nb_cof_vid_update = 1;
+ break;
+ }
}
+ return nb_cof_vid_update;
+}
+
+static u32 init_fidvid_core(u32 nodeid, u32 coreid)
+{
+ device_t dev;
+ u32 vid_max;
+ u32 fid_max = 0;
+ u8 nb_cof_vid_update = needs_NB_COF_VID_update();
+ u8 pvimode;
+ u32 reg1fc;
+
+ /* Steps 1-6 of BIOS NB COF and VID Configuration
+ * for SVI and Single-Plane PVI Systems. BKDG 2.4.2.9 #31116 rev 3.48
+ */
+ dev = NODE_PCI(nodeid, 3);
+ pvimode = pci_read_config32(dev, PW_CTL_MISC) & PVI_MODE;
+ reg1fc = pci_read_config32(dev, 0x1FC);
+
+ if (nb_cof_vid_update) {
+ vid_max = (reg1fc & SINGLE_PLANE_NB_VID_MASK ) >> SINGLE_PLANE_NB_VID_SHIFT ;
+ fid_max = (reg1fc & SINGLE_PLANE_NB_FID_MASK ) >> SINGLE_PLANE_NB_FID_SHIFT ;
- send = (nb_cof_vid_update << 16) | (fid_max << 8);
- send |= (apicid << 24); // ap apicid
+ if (!pvimode) { /* SVI, dual power plane */
+ vid_max = vid_max - ((reg1fc & DUAL_PLANE_NB_VID_OFF_MASK ) >> DUAL_PLANE_NB_VID_SHIFT );
+ fid_max = fid_max + ((reg1fc & DUAL_PLANE_NB_FID_OFF_MASK ) >> DUAL_PLANE_NB_FID_SHIFT );
+ }
+ /* write newNbVid to P-state Reg's NbVid always if NbVidUpdatedAll=1 */
+ fixPsNbVidBeforeWR(vid_max, coreid,dev,pvimode);
+
+ /* fid setup is handled by the BSP at the end. */
+
+ } else { /* ! nb_cof_vid_update */
+ /* Use max values */
+ if (pvimode)
+ UpdateSinglePlaneNbVid();
+ }
+
+ return ((nb_cof_vid_update << 16) | (fid_max << 8));
+
+}
+
+static void init_fidvid_ap(u32 apicid, u32 nodeid, u32 coreid)
+{
+ u32 send;
+
+ printk(BIOS_DEBUG, "FIDVID on AP: %02x\n", apicid);
+
+ send = init_fidvid_core(nodeid,coreid);
+ send |= (apicid << 24); // ap apicid
// Send signal to BSP about this AP max fid
// This also indicates this AP is ready for warm reset (if required).
- lapic_write(LAPIC_MSG_REG, send | 1);
+ lapic_write(LAPIC_MSG_REG, send | F10_APSTATE_RESET);
}
static u32 calc_common_fid(u32 fid_packed, u32 fid_packed_new)
fidmax_new = (fid_packed_new >> 8) & 0xFF;
- if(fidmax > fidmax_new) {
+ if (fidmax > fidmax_new) {
fidmax = fidmax_new;
}
fid_packed &= 0xFF << 16;
fid_packed |= (fidmax << 8);
- fid_packed |= fid_packed_new & (0xFF << 16); // set nb_cof_vid_update
+ fid_packed |= fid_packed_new & (0xFF << 16); // set nb_cof_vid_update
return fid_packed;
}
-struct fidvid_st {
- u32 common_fid;
-};
-
-static void init_fidvid_bsp_stage1(u32 ap_apicid, void *gp )
+static void init_fidvid_bsp_stage1(u32 ap_apicid, void *gp)
{
- u32 readback = 0;
- u32 timeout = 1;
+ u32 readback = 0;
+ u32 timeout = 1;
- struct fidvid_st *fvp = gp;
- int loop;
+ struct fidvid_st *fvp = gp;
+ int loop;
- print_debug_fv("Wait for AP stage 1: ap_apicid = ", ap_apicid);
+ print_debug_fv("Wait for AP stage 1: ap_apicid = ", ap_apicid);
- loop = 100000;
- while(--loop > 0) {
- if(lapic_remote_read(ap_apicid, LAPIC_MSG_REG, &readback) != 0) continue;
- if((readback & 0x3f) == 1) {
- timeout = 0;
- break; //target ap is in stage 1
- }
+ loop = 100000;
+ while (--loop > 0) {
+ if (lapic_remote_read(ap_apicid, LAPIC_MSG_REG, &readback) != 0)
+ continue;
+ if ((readback & 0x3f) == 1) {
+ timeout = 0;
+ break; /* target ap is in stage 1 */
}
+ }
- if(timeout) {
- print_initcpu8("fidvid_bsp_stage1: time out while reading from ap ", ap_apicid);
- return;
- }
+ if (timeout) {
+ printk(BIOS_DEBUG, "%s: timed out reading from ap %02x\n",
+ __func__, ap_apicid);
+ return;
+ }
+
+ print_debug_fv("\treadback = ", readback);
+
+ fvp->common_fid = calc_common_fid(fvp->common_fid, readback);
+
+ print_debug_fv("\tcommon_fid(packed) = ", fvp->common_fid);
- print_debug_fv("\treadback = ", readback);
+}
+
+static void fixPsNbVidAfterWR(u32 newNbVid, u8 NbVidUpdatedAll,u8 pviMode)
+{
+ msr_t msr;
+ u8 i;
+ u8 StartupPstate;
+
+ /* BKDG 2.4.2.9.1 11-12
+ * This function copies newNbVid to NbVid bits in P-state
+ * Registers[4:0] if its NbDid bit=0, and IddValue!=0 in case of
+ * NbVidUpdatedAll =0 or copies newNbVid to NbVid bits in
+ * P-state Registers[4:0] if its IddValue!=0 in case of
+ * NbVidUpdatedAll=1. Then transition to StartPstate.
+ */
+
+ /* write newNbVid to P-state Reg's NbVid if its NbDid=0 */
+ for (i = 0; i < 5; i++) {
+ msr = rdmsr(0xC0010064 + i);
+ /* NbDid (bit 22 of P-state Reg) == 0 or NbVidUpdatedAll = 1 */
+ if ( (msr.hi & PS_IDD_VALUE_MASK)
+ && (msr.hi & PS_EN_MASK)
+ &&(((msr.lo & PS_NB_DID_MASK) == 0) || NbVidUpdatedAll)) {
+ msr.lo &= PS_NB_VID_M_OFF;
+ msr.lo |= (newNbVid & 0x7F) << PS_NB_VID_SHFT;
+ wrmsr(0xC0010064 + i, msr);
+ }
+ }
- fvp->common_fid = calc_common_fid(fvp->common_fid, readback);
+ /* Not documented. Would overwrite Nb_Vids just copied
+ * should we just update cpu_vid or nothing at all ?
+ */
+ if (pviMode) { //single plane
+ UpdateSinglePlaneNbVid();
+ }
+ /* For each core in the system, transition all cores to StartupPstate */
+ msr = rdmsr(0xC0010071);
+ StartupPstate = msr.hi & 0x07;
- print_debug_fv("\tcommon_fid(packed) = ", fvp->common_fid);
+ /* Set and wait for StartupPstate to set. */
+ set_pstate(StartupPstate);
}
+static void finalPstateChange(void)
+{
+ /* Enble P0 on all cores for best performance.
+ * Linux can slow them down later if need be.
+ * It is safe since they will be in C1 halt
+ * most of the time anyway.
+ */
+ set_pstate(0);
+}
static void init_fidvid_stage2(u32 apicid, u32 nodeid)
{
msr_t msr;
device_t dev;
u32 reg1fc;
- u8 StartupPstate;
- u8 nbvid;
- int i;
+ u32 dtemp;
+ u32 nbvid;
+ u8 nb_cof_vid_update = needs_NB_COF_VID_update();
+ u8 NbVidUpdateAll;
+ u8 pvimode;
/* After warm reset finish the fid/vid setup for all cores. */
- dev = NODE_PCI(nodeid,3);
+
+ /* If any node has nb_cof_vid_update set all nodes need an update. */
+
+ dev = NODE_PCI(nodeid, 3);
+ pvimode = (pci_read_config32(dev, 0xA0) >> 8) & 1;
reg1fc = pci_read_config32(dev, 0x1FC);
nbvid = (reg1fc >> 7) & 0x7F;
+ NbVidUpdateAll = (reg1fc >> 1) & 1;
- if (reg1fc & 0x02) { // NbVidUpdateAll ?
- for( i = 0; i < 5; i++) {
- msr = rdmsr(0xC0010064 + i);
- if ((msr.hi >> 31) & 1) { // PstateEn?
- msr.lo &= ~(0x7F << 25);
- msr.lo |= (nbvid & 0x7F) << 25;
- }
- }
- } else {
- for( i = 0; i < 5; i++) {
- msr = rdmsr(0xC0010064 + i);
- if (((msr.hi >> 31) & 1) && (((msr.lo >> 22) & 1) == 0)) { // PstateEn and PDid == 0?
- msr.lo &= ~(0x7F << 25);
- msr.lo |= (nbvid & 0x7F) << 25;
- }
+ if (nb_cof_vid_update) {
+ if (!pvimode) { /* SVI */
+ nbvid = nbvid - ((reg1fc >> 17) & 0x1F);
}
+ /* write newNbVid to P-state Reg's NbVid if its NbDid=0 */
+ fixPsNbVidAfterWR(nbvid, NbVidUpdateAll,pvimode);
+ } else { /* !nb_cof_vid_update */
+ if (pvimode)
+ UpdateSinglePlaneNbVid();
}
+ dtemp = pci_read_config32(dev, 0xA0);
+ dtemp &= PLLLOCK_OFF;
+ dtemp |= PLLLOCK_DFT_L;
+ pci_write_config32(dev, 0xA0, dtemp);
- // For each processor in the system, transition all cores to StartupPstate
- msr = rdmsr(0xC0010071);
- StartupPstate = msr.hi >> (32-32) & 0x03;
- msr = rdmsr(0xC0010062);
- msr.lo = StartupPstate;
- wrmsr(0xC0010062, msr);
+ dualPlaneOnly(dev);
+ applyBoostFIDOffset(dev);
+ enableNbPState1(dev);
+
+ finalPstateChange();
+
+ /* Set TSC to tick at the P0 ndfid rate */
+ msr = rdmsr(HWCR);
+ msr.lo |= 1 << 24;
+ wrmsr(HWCR, msr);
}
-#if FAM10_SET_FIDVID_STORE_AP_APICID_AT_FIRST == 1
+#if CONFIG_SET_FIDVID_STORE_AP_APICID_AT_FIRST
struct ap_apicid_st {
u32 num;
// it could use 256 bytes for 64 node quad core system
static int init_fidvid_bsp(u32 bsp_apicid, u32 nodes)
{
-#if FAM10_SET_FIDVID_STORE_AP_APICID_AT_FIRST == 1
+#if CONFIG_SET_FIDVID_STORE_AP_APICID_AT_FIRST
struct ap_apicid_st ap_apicidx;
u32 i;
#endif
struct fidvid_st fv;
- msr_t msr;
- device_t dev;
- u8 vid_max;
- u8 fid_max;
- u8 startup_pstate;
- u8 nb_cof_vid_update;
- u32 reg1fc;
- u32 dword;
- u8 pvimode;
- printk_debug("FIDVID on BSP, APIC_id: %02x\n", bsp_apicid);
+ printk(BIOS_DEBUG, "FIDVID on BSP, APIC_id: %02x\n", bsp_apicid);
- /* FIXME: Only support single plane system at this time. */
/* Steps 1-6 of BIOS NB COF and VID Configuration
- * for Single-Plane PVI Systems
+ * for SVI and Single-Plane PVI Systems.
*/
- dev = NODE_PCI(0,3); // nodeid for the BSP is 0
- reg1fc = pci_read_config32(dev, 0x1FC);
- nb_cof_vid_update = reg1fc & 1;
- if (nb_cof_vid_update) {
- /* Get fused settings */
- dword = pci_read_config32(dev, 0xa0);
- pvimode = (dword >> 8) & 1;
-
- vid_max = (reg1fc >> 7) & 0x7F; // per node
- fid_max = (reg1fc >> 2) & 0x1F; // per system
-
- if (pvimode) {
- /* FIXME: support daul plane mode */
- die("PVImode not supported\n");
- /* fidmax = vidmax - (reg1fc >> 17) & 0x1F;
- fidmax = fidmax + (reg1fc >> 14) & 0x03;
- */
- }
-
- } else {
- /* Use current values */
- msr = rdmsr(0xc0010071);
- fid_max = ((msr.hi >> (59-32)) & 0x1f); //max nb fid
- vid_max = ((msr.hi >> (35-32)) & 0x7f); //max vid
- }
-
- /* Note this is the single plane setup. Need to add dual plane path */
- msr = rdmsr(0xc0010071);
- startup_pstate = (msr.hi >> (32-32)) & 0x07;
-
-
- /* Copy startup pstate to P1 and P0 MSRs. Set the maxvid for this node in P0.
- Then transition to P1 for corex and P0 for core0. */
- msr = rdmsr(0xC0010064 + startup_pstate);
- wrmsr(0xC0010065, msr);
- wrmsr(0xC0010064, msr);
- msr.lo &= ~0xFE000000; // clear nbvid
- msr.lo |= vid_max << 25;
- wrmsr(0xC0010064, msr);
+ fv.common_fid = init_fidvid_core(0,0);
- // Transition to P1 and then P0 for core0.
- msr = rdmsr(0xC0010062);
- msr.lo = (msr.lo & ~0x07) | 1;
- wrmsr(0xC0010062, msr);
-
- // Wait for P1 to set.
- do {
- msr = rdmsr(0xC0010063);
- } while (msr.lo != 1);
-
- msr.lo = msr.lo & ~0x07;
- wrmsr(0xC0010062, msr);
- // Wait for P0 to set.
- do {
- msr = rdmsr(0xC0010063);
- } while (msr.lo != 0);
-
-
- fv.common_fid = (nb_cof_vid_update << 16) | (fid_max << 8) ;
print_debug_fv("BSP fid = ", fv.common_fid);
-#if FAM10_SET_FIDVID_STORE_AP_APICID_AT_FIRST == 1 && FAM10_SET_FIDVID_CORE0_ONLY == 0
+#if CONFIG_SET_FIDVID_STORE_AP_APICID_AT_FIRST && !CONFIG_SET_FIDVID_CORE0_ONLY
/* For all APs (We know the APIC ID of all APs even when the APIC ID
is lifted) remote read from AP LAPIC_MSG_REG about max fid.
Then calculate the common max fid that can be used for all
APs and BSP */
ap_apicidx.num = 0;
- for_each_ap(bsp_apicid, FAM10_SET_FIDVID_CORE_RANGE, store_ap_apicid, &ap_apicidx);
+ for_each_ap(bsp_apicid, CONFIG_SET_FIDVID_CORE_RANGE, store_ap_apicid, &ap_apicidx);
- for(i = 0; i < ap_apicidx.num; i++) {
+ for (i = 0; i < ap_apicidx.num; i++) {
init_fidvid_bsp_stage1(ap_apicidx.apicid[i], &fv);
}
#else
- for_each_ap(bsp_apicid, FAM10_SET_FIDVID_CORE0_ONLY, init_fidvid_bsp_stage1, &fv);
+ for_each_ap(bsp_apicid, CONFIG_SET_FIDVID_CORE0_ONLY, init_fidvid_bsp_stage1, &fv);
#endif
print_debug_fv("common_fid = ", fv.common_fid);
- if (fv.common_fid & ~(0xFF << 16)) { // check nb_cof_vid_update
+ if (fv.common_fid & (1 << 16)) { /* check nb_cof_vid_update */
// Enable the common fid and other settings.
enable_fid_change((fv.common_fid >> 8) & 0x1F);
return 1;
}
- return 0; // No FID/VID changes. Don't reset
-}
-static void set_p0(void)
-{
- msr_t msr;
-
- // Transition P0 for calling core.
- msr = rdmsr(0xC0010062);
- msr.lo = (msr.lo & ~0x07);
- wrmsr(0xC0010062, msr);
-
- // Don't bother to wait around for the P state to change.
+ return 0; // No FID/VID changes. Don't reset
}
#endif
projects / coreboot.git / blobdiff