add target for amd serenade board

git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1609 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1

diff --git a/targets/amd/serenade/Config.lb b/targets/amd/serenade/Config.lb
new file mode 100644 (file)
index 0000000..b4e8014
--- /dev/null
+++ b/targets/amd/serenade/Config.lb
@@ -0,0 +1,113 @@
+# the AMD Serenade
+# This will make a target directory of ./e325
+
+loadoptions
+
+target serenade
+
+uses ARCH
+uses CONFIG_COMPRESS
+uses CONFIG_IOAPIC
+uses CONFIG_ROM_STREAM
+uses CONFIG_ROM_STREAM_START
+uses CONFIG_SERIAL_POST
+uses NO_POST
+uses CONFIG_UDELAY_TSC
+uses CPU_FIXUP
+uses FALLBACK_SIZE
+uses HAVE_FALLBACK_BOOT
+uses HAVE_MP_TABLE
+uses HAVE_PIRQ_TABLE
+uses HAVE_HARD_RESET
+uses i586
+uses i686
+uses INTEL_PPRO_MTRR
+uses HEAP_SIZE
+uses IRQ_SLOT_COUNT
+uses k7
+uses k8
+uses MAINBOARD_PART_NUMBER
+uses MAINBOARD_VENDOR
+uses CONFIG_SMP
+uses CONFIG_MAX_CPUS
+uses MEMORY_HOLE
+uses PAYLOAD_SIZE
+uses _RAMBASE
+uses _ROMBASE
+uses ROM_IMAGE_SIZE
+uses ROM_SECTION_OFFSET
+uses ROM_SECTION_SIZE
+uses ROM_SIZE
+uses STACK_SIZE
+uses USE_FALLBACK_IMAGE
+uses USE_OPTION_TABLE
+uses HAVE_OPTION_TABLE
+uses MAXIMUM_CONSOLE_LOGLEVEL
+uses  DEFAULT_CONSOLE_LOGLEVEL
+uses  CONFIG_CONSOLE_SERIAL8250
+uses MAINBOARD
+uses CONFIG_CHIP_CONFIGURE
+uses XIP_ROM_SIZE
+uses XIP_ROM_BASE
+uses LINUXBIOS_EXTRA_VERSION
+
+option CONFIG_CHIP_CONFIGURE=1
+
+option  MAXIMUM_CONSOLE_LOGLEVEL=8
+option  DEFAULT_CONSOLE_LOGLEVEL=8
+option  CONFIG_CONSOLE_SERIAL8250=1
+option  CONFIG_SERIAL_POST=1
+option  NO_POST=0
+
+option CPU_FIXUP=1
+option CONFIG_UDELAY_TSC=0
+option i686=1
+option i586=1
+option INTEL_PPRO_MTRR=1
+option k7=1
+option k8=1
+
+option ROM_SIZE=1048576
+
+
+option HAVE_OPTION_TABLE=1
+option CONFIG_ROM_STREAM=1
+option HAVE_FALLBACK_BOOT=1
+
+###
+### Compute the location and size of where this firmware image
+### (linuxBIOS plus bootloader) will live in the boot rom chip.
+###
+option FALLBACK_SIZE=131072
+
+## LinuxBIOS C code runs at this location in RAM
+option _RAMBASE=0x00004000
+
+#
+###
+### Compute the start location and size size of
+### The linuxBIOS bootloader.
+###
+
+#
+# Arima hdama
+romimage "normal"
+       option USE_FALLBACK_IMAGE=0
+       option ROM_IMAGE_SIZE=0x10000
+       option LINUXBIOS_EXTRA_VERSION=".0Normal"
+       mainboard amd/serenade
+       payload /home/ollie/work/filo-0.4.1/filo.elf
+end
+
+romimage "fallback" 
+       option USE_FALLBACK_IMAGE=1
+       option ROM_IMAGE_SIZE=0x10000
+       option LINUXBIOS_EXTRA_VERSION=".0Fallback"
+       mainboard amd/serenade
+       payload /home/ollie/work/filo-0.4.1/filo.elf
+
+# use this to test a build if you don't have the etherboot
+#      payload /etc/hosts
+end
+
+buildrom ./linuxbios.rom ROM_SIZE "normal" "fallback"