uses HAVE_MP_TABLE
uses HAVE_PIRQ_TABLE
uses USE_FALLBACK_IMAGE
+uses LB_CKS_RANGE_START
+uses LB_CKS_RANGE_END
+uses LB_CKS_LOC
uses MAINBOARD
uses ARCH
uses HARD_RESET_BUS
register "fixup_vga" = "1"
+##
+## Move the default LinuxBIOS cmos range off of AMD RTC registers
+##
+default LB_CKS_RANGE_START=49
+default LB_CKS_RANGE_END=122
+default LB_CKS_LOC=123
+
driver mainboard.o
-driver adaptec_scsi.o
-driver promise_sata.o
-driver intel_nic.o
-driver broadcom_nic.o
+#driver adaptec_scsi.o
+#driver si_sata.o
+#driver intel_nic_ipmi.o
+#driver broadcom_nic_ipmi.o
#object reset.o
-#object static_devices.o
if HAVE_MP_TABLE object mptable.o end
if HAVE_PIRQ_TABLE object irq_tables.o end
#
###
mainboardinit cpu/i386/entry16.inc
mainboardinit cpu/i386/entry32.inc
+mainboardinit cpu/i386/bist32.inc
ldscript /cpu/i386/entry16.lds
ldscript /cpu/i386/entry32.lds
#
###
### Setup the serial port
###
-#mainboardinit superiowinbond/w83627hf/setup_serial.inc
mainboardinit pc80/serial.inc
mainboardinit arch/i386/lib/console.inc
+mainboardinit cpu/i386/bist32_fail.inc
#
####
#### O.k. We aren't just an intermediary anymore!
###
### Romcc output
###
-#makerule ./failover.E dep "$(MAINBOARD)/failover.c" act "$(CPP) -I$(TOP)/src $(CPPFLAGS) $(MAINBOARD)/failover.c > ./failever.E"
-#makerule ./failover.inc dep "./romcc ./failover.E" act "./romcc -O ./failover.E > failover.inc"
-#mainboardinit .failover.inc
makerule ./failover.E
depends "$(MAINBOARD)/failover.c"
makerule ./failover.inc
depends "./romcc ./failover.E"
- action "./romcc -O -o failover.inc --label-prefix=failover ./failover.E"end
+ action "./romcc -O -o failover.inc --label-prefix=failover ./failover.E"
+end
makerule ./auto.E
- depends "$(MAINBOARD)/auto.c"
- action "$(CPP) -I$(TOP)/src $(ROMCCPPFLAGS) $(CPPFLAGS) $(MAINBOARD)/auto.c > ./auto.E"
+ depends "$(MAINBOARD)/auto.c option_table.h"
+ action "$(CPP) -I$(TOP)/src -I. $(ROMCCPPFLAGS) $(CPPFLAGS) $(MAINBOARD)/auto.c > ./auto.E"
end
makerule ./auto.inc
depends "./romcc ./auto.E"
- action "./romcc -O -mcpu=k8 -o auto.inc --label-prefix=auto ./auto.E"
-# action "./romcc -mcpu=k8 -O ./auto.E > auto.inc"
+ action "./romcc -O2 -mcpu=k8 -o auto.inc --label-prefix=auto ./auto.E"
end
mainboardinit cpu/k8/enable_mmx_sse.inc
mainboardinit ./auto.inc
###
### Include the secondary Configuration files
###
+
northbridge amd/amdk8 "mc0"
pci 0:18.0
pci 0:18.0
pci 1:0.1 on
pci 1:0.2 on
pci 1:1.0 off
+ superio winbond/w83627hf link 1
+ pnp 2e.0 on # Floppy
+ io 0x60 = 0x3f0
+ irq 0x70 = 6
+ drq 0x74 = 2
+ pnp 2e.1 off # Parallel Port
+ io 0x60 = 0x378
+ irq 0x70 = 7
+ pnp 2e.2 on # Com1
+ io 0x60 = 0x3f8
+ irq 0x70 = 4
+ pnp 2e.3 off # Com2
+ io 0x60 = 0x2f8
+ irq 0x70 = 3
+ pnp 2e.5 on # Keyboard
+ io 0x60 = 0x60
+ io 0x62 = 0x64
+ irq 0x70 = 1
+ irq 0x72 = 12
+ pnp 2e.6 off # CIR
+ pnp 2e.7 off # GAME_MIDI_GIPO1
+ pnp 2e.8 off # GPIO2
+ pnp 2e.9 off # GPIO3
+ pnp 2e.a off # ACPI
+ pnp 2e.b on # HW Monitor
+ io 0x60 = 0x290
+ end
end
end
-#northbridge amd/amdk8
-#end
-#southbridge amd/amd8111 "amd8111"
-#end
-#mainboardinit archi386/smp/secondary.inc
-#superio NSC/pc87360
-# register "com1" = "{1}"
-# register "lpt" = "{1}"
-#end
dir /pc80
-##dir /src/superio/winbond/w83627hf
#dir /bioscall
-#dir /cpu/k8
cpu k8 "cpu0"
register "up" = "{.chip = &amd8111, .ht_width=8, .ht_speed=200}"
end
#define ASSEMBLY 1
#include <stdint.h>
#include <device/pci_def.h>
-#include <cpu/p6/apic.h>
#include <arch/io.h>
+#include <device/pnp_def.h>
#include <arch/romcc_io.h>
+#include <arch/smp/lapic.h>
+#include "option_table.h"
+#include "pc80/mc146818rtc_early.c"
#include "pc80/serial.c"
#include "arch/i386/lib/console.c"
#include "ram/ramtest.c"
-#include "northbridge/amd/amdk8/early_ht.c"
+#include "northbridge/amd/amdk8/incoherent_ht.c"
#include "southbridge/amd/amd8111/amd8111_early_smbus.c"
#include "northbridge/amd/amdk8/raminit.h"
#include "cpu/k8/apic_timer.c"
#include "lib/delay.c"
#include "cpu/p6/boot_cpu.c"
#include "northbridge/amd/amdk8/reset_test.c"
-#include "northbridge/amd/amdk8/debug.c"
+#include "northbridge/amd/amdk8/debug.c"
#include "northbridge/amd/amdk8/cpu_rev.c"
-
+#include "superio/winbond/w83627hf/w83627hf_early_serial.c"
+
+#define SERIAL_DEV PNP_DEV(0x2e, W83627HF_SP1)
+
+static void hard_reset(void)
+{
+ set_bios_reset();
+
+ /* enable cf9 */
+ pci_write_config8(PCI_DEV(0, 0x02, 3), 0x41, 0xf1);
+ /* reset */
+ outb(0x0e, 0x0cf9);
+}
+static void soft_reset(void)
+{
+ set_bios_reset();
+ pci_write_config8(PCI_DEV(0, 0x02, 0), 0x47, 1);
+}
+
#define REV_B_RESET 0
static void memreset_setup(void)
{
-#if REV_B_RESET==1
+ if (is_cpu_pre_c0()) {
outb((0 << 7)|(0 << 6)|(0<<5)|(0<<4)|(1<<2)|(0<<0), SMBUS_IO_BASE + 0xc0 + 16); //REVC_MEMRST_EN=0
-#else
+ }
+ else {
outb((0 << 7)|(0 << 6)|(0<<5)|(0<<4)|(1<<2)|(1<<0), SMBUS_IO_BASE + 0xc0 + 16); //REVC_MEMRST_EN=1
-#endif
- outb((0 << 7)|(0 << 6)|(0<<5)|(0<<4)|(1<<2)|(0<<0), SMBUS_IO_BASE + 0xc0 + 17);
+ }
+ outb((0 << 7)|(0 << 6)|(0<<5)|(0<<4)|(1<<2)|(0<<0), SMBUS_IO_BASE + 0xc0 + 17);
}
static void memreset(int controllers, const struct mem_controller *ctrl)
{
+ if (is_cpu_pre_c0()) {
udelay(800);
-#if REV_B_RESET==1
outb((0<<7)|(0<<6)|(0<<5)|(0<<4)|(1<<2)|(1<<0), SMBUS_IO_BASE + 0xc0 + 17); //REVB_MEMRST_L=1
-#endif
udelay(90);
+ }
}
+
static unsigned int generate_row(uint8_t node, uint8_t row, uint8_t maxnodes)
{
+ /* Routing Table Node i
+ *
+ * F0: 0x40, 0x44, 0x48, 0x4c, 0x50, 0x54, 0x58, 0x5c
+ * i: 0, 1, 2, 3, 4, 5, 6, 7
+ *
+ * [ 0: 3] Request Route
+ * [0] Route to this node
+ * [1] Route to Link 0
+ * [2] Route to Link 1
+ * [3] Route to Link 2
+ * [11: 8] Response Route
+ * [0] Route to this node
+ * [1] Route to Link 0
+ * [2] Route to Link 1
+ * [3] Route to Link 2
+ * [19:16] Broadcast route
+ * [0] Route to this node
+ * [1] Route to Link 0
+ * [2] Route to Link 1
+ * [3] Route to Link 2
+ */
+
uint32_t ret=0x00010101; /* default row entry */
+
return ret;
}
+static inline void activate_spd_rom(const struct mem_controller *ctrl)
+{
+ /* nothing to do */
+}
+
static inline int spd_read_byte(unsigned device, unsigned address)
{
return smbus_read_byte(device, address);
}
-/* include mainboard specific ht code */
-#include "hypertransport.c"
-
-//#include "northbridge/amd/amdk8/cpu_ldtstop.c"
-//#include "southbridge/amd/amd8111/amd8111_ldtstop.c"
-
#include "northbridge/amd/amdk8/raminit.c"
#include "northbridge/amd/amdk8/coherent_ht.c"
#include "sdram/generic_sdram.c"
-static void enable_lapic(void)
-{
- msr_t msr;
- msr = rdmsr(0x1b);
- msr.hi &= 0xffffff00;
- msr.lo &= 0x000007ff;
- msr.lo |= APIC_DEFAULT_BASE | (1 << 11);
- wrmsr(0x1b, msr);
-}
-
-static void stop_this_cpu(void)
-{
- unsigned apicid;
- apicid = apic_read(APIC_ID) >> 24;
-
- /* Send an APIC INIT to myself */
- apic_write(APIC_ICR2, SET_APIC_DEST_FIELD(apicid));
- apic_write(APIC_ICR, APIC_INT_LEVELTRIG | APIC_INT_ASSERT | APIC_DM_INIT);
- /* Wait for the ipi send to finish */
- apic_wait_icr_idle();
-
- /* Deassert the APIC INIT */
- apic_write(APIC_ICR2, SET_APIC_DEST_FIELD(apicid));
- apic_write(APIC_ICR, APIC_INT_LEVELTRIG | APIC_DM_INIT);
- /* Wait for the ipi send to finish */
- apic_wait_icr_idle();
-
- /* If I haven't halted spin forever */
- for(;;) {
- hlt();
- }
-}
-#define FIRST_CPU 1
-#define SECOND_CPU 0
-#define TOTAL_CPUS (FIRST_CPU + SECOND_CPU)
static void main(void)
{
+ /*
+ * GPIO28 of 8111 will control H0_MEMRESET_L
+ * GPIO29 of 8111 will control H1_MEMRESET_L
+ */
static const struct mem_controller cpu[] = {
-#if FIRST_CPU
{
.node_id = 0,
.f0 = PCI_DEV(0, 0x18, 0),
.channel0 = { (0xa<<3)|0, (0xa<<3)|2, 0, 0 },
.channel1 = { (0xa<<3)|1, (0xa<<3)|3, 0, 0 },
},
-#endif
-#if SECOND_CPU
- {
- .node_id = 1,
- .f0 = PCI_DEV(0, 0x19, 0),
- .f1 = PCI_DEV(0, 0x19, 1),
- .f2 = PCI_DEV(0, 0x19, 2),
- .f3 = PCI_DEV(0, 0x19, 3),
- .channel0 = { (0xa<<3)|4, (0xa<<3)|6, 0, 0 },
- .channel1 = { (0xa<<3)|5, (0xa<<3)|7, 0, 0 },
- },
-#endif
};
- if (cpu_init_detected()) {
- asm("jmp __cpu_reset");
- }
- enable_lapic();
- init_timer();
- if (!boot_cpu() ) {
- notify_bsp_ap_is_stopped();
- stop_this_cpu();
- }
- uart_init();
- console_init();
- setup_default_resource_map();
- setup_coherent_ht_domain();
- enumerate_ht_chain(0);
- distinguish_cpu_resets(0);
-
+
+ int needs_reset;
+ enable_lapic();
+ init_timer();
+ if (cpu_init_detected()) {
+ asm("jmp __cpu_reset");
+ }
+ distinguish_cpu_resets();
+ if (!boot_cpu()) {
+ stop_this_cpu();
+ }
+ w83627hf_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ uart_init();
+ console_init();
+ setup_default_resource_map();
+ needs_reset = setup_coherent_ht_domain();
+ needs_reset |= ht_setup_chain(PCI_DEV(0, 0x18, 0), 0x80);
+ if (needs_reset) {
+ print_info("ht reset -\r\n");
+ soft_reset();
+ }
#if 0
print_pci_devices();
#endif
enable_smbus();
#if 0
- dump_spd_registers(&cpu[0]);
+// dump_spd_registers(&cpu[0]);
+ dump_smbus_registers();
#endif
+
memreset_setup();
sdram_initialize(sizeof(cpu)/sizeof(cpu[0]), cpu);
386 1 e 1 ECC_memory
388 4 r 0 reboot_bits
392 3 e 5 baud_rate
+395 1 e 1 hw_scrubber
+396 1 e 1 interleave_chip_selects
+397 2 e 8 max_mem_clock
400 1 e 1 power_on_after_fail
412 4 e 6 debug_level
416 4 e 7 boot_first
424 4 e 7 boot_third
428 4 h 0 boot_index
432 8 h 0 boot_countdown
-1008 16 h 0 check_sum
+440 4 e 9 slow_cpu
+444 1 e 1 nmi
+728 256 h 0 user_data
+984 16 h 0 check_sum
+# Reserve the extended AMD configuration registers
+1000 24 r 0 reserved_memory
+
+
enumerations
7 9 Fallback_HDD
7 10 Fallback_Floppy
#7 3 ROM
+8 0 200Mhz
+8 1 166Mhz
+8 2 133Mhz
+8 3 100Mhz
+9 0 off
+9 1 87.5%
+9 2 75.0%
+9 3 62.5%
+9 4 50.0%
+9 5 37.5%
+9 6 25.0%
+9 7 12.5%
checksums
-checksum 392 1007 1008
+checksum 392 983 984
#include <device/pci_def.h>
#include <device/pci_ids.h>
#include <arch/io.h>
-#include "arch/romcc_io.h"
+#include <arch/romcc_io.h>
+#include <arch/smp/lapic.h>
#include "pc80/mc146818rtc_early.c"
#include "southbridge/amd/amd8111/amd8111_enable_rom.c"
#include "northbridge/amd/amdk8/early_ht.c"
#include "cpu/p6/boot_cpu.c"
#include "northbridge/amd/amdk8/reset_test.c"
+#define HAVE_REGPARM_SUPPORT 0
+#if HAVE_REGPARM_SUPPORT
+static unsigned long main(unsigned long bist)
+{
+#else
static void main(void)
{
- /* Nothing special needs to be done to find bus 0 */
- /* Allow the HT devices to be found */
- enumerate_ht_chain(0);
+ unsigned long bist = 0;
+#endif
+ /* Make cerain my local apic is useable */
+ enable_lapic();
- /* Setup the 8111 */
- amd8111_enable_rom();
-
- /* Is this a cpu reset? */
+ /* Is this a cpu only reset? */
if (cpu_init_detected()) {
if (last_boot_normal()) {
- asm("jmp __normal_image");
+ goto normal_image;
} else {
- asm("jmp __cpu_reset");
+ goto cpu_reset;
}
}
/* Is this a secondary cpu? */
- else if (!boot_cpu() && last_boot_normal()) {
- asm("jmp __normal_image");
+ if (!boot_cpu()) {
+ if (last_boot_normal()) {
+ goto normal_image;
+ } else {
+ goto fallback_image;
+ }
+ }
+
+
+ /* Nothing special needs to be done to find bus 0 */
+ /* Allow the HT devices to be found */
+ enumerate_ht_chain();
+
+ /* Setup the 8111 */
+ amd8111_enable_rom();
+
+ /* Is this a deliberate reset by the bios */
+ if (bios_reset_detected() && last_boot_normal()) {
+ goto normal_image;
}
/* This is the primary cpu how should I boot? */
else if (do_normal_boot()) {
- asm("jmp __normal_image");
+ goto normal_image;
+ }
+ else {
+ goto fallback_image;
}
+ normal_image:
+ asm("jmp __normal_image"
+ : /* outputs */
+ : "a" (bist) /* inputs */
+ : /* clobbers */
+ );
+ cpu_reset:
+ asm("jmp __cpu_reset"
+ : /* outputs */
+ : "a"(bist) /* inputs */
+ : /* clobbers */
+ );
+ fallback_image:
+#if HAVE_REGPARM_SUPPORT
+ return bist;
+#else
+ return;
+#endif
}
{
{1,(2<<3)|0, {{0x1, 0xdef8}, {0x2, 0xdef8}, {0x3, 0xdef8}, {0x4, 0xdef8}}, 0, 0},
{0x2,0, {{0, 0}, {0, 0}, {0, 0}, {0x4, 0xdef8}}, 0, 0},
- {0x2,0x68, {{0x4, 0xdef8}, {0, 0}, {0, 0}, {0, 0}}, 0, 0},
- {0x2,0x58, {{0x3, 0xdef8}, {0, 0}, {0, 0}, {0, 0}}, 0, 0},
- {0x2,0x18, {{0x1, 0xdef8}, {0x2, 0xdef8}, {0x3, 0xdef8}, {0x4, 0xdef8}}, 0x5, 0},
- {0x2,0x30, {{0x2, 0xdef8}, {0x3, 0xdef8}, {0x4, 0xdef8}, {0x1, 0xdef8}}, 0x1, 0},
- {0x2,0x38, {{0x3, 0xdef8}, {0x4, 0xdef8}, {0x1, 0xdef8}, {0x2, 0xdef8}}, 0x2, 0},
- {0x2,0x40, {{0x4, 0xdef8}, {0x1, 0xdef8}, {0x2, 0xdef8}, {0x3, 0xdef8}}, 0x3, 0},
- {0x2,0x48, {{0x1, 0xdef8}, {0x2, 0xdef8}, {0x3, 0xdef8}, {0x4, 0xdef8}}, 0x4, 0},
- {0x2,0x50, {{0x2, 0xdef8}, {0x3, 0xdef8}, {0x4, 0xdef8}, {0x1, 0xdef8}}, 0x5, 0},
- {0x2,0x70, {{0x1, 0xdef8}, {0, 0}, {0, 0}, {0, 0}}, 0, 0},
- {0x2,0x60, {{0x2, 0xdef8}, {0, 0}, {0, 0}, {0, 0}}, 0, 0},
+ {0x2,(0x0d<<3)|0, {{0x4, 0xdef8}, {0, 0}, {0, 0}, {0, 0}}, 0, 0},
+ {0x2,(0x0b<<3)|0, {{0x3, 0xdef8}, {0, 0}, {0, 0}, {0, 0}}, 0, 0},
+ {0x2,(3<<3)|0, {{0x1, 0xdef8}, {0x2, 0xdef8}, {0x3, 0xdef8}, {0x4, 0xdef8}}, 0x5, 0},
+ {0x2,(6<<3)|0, {{0x2, 0xdef8}, {0x3, 0xdef8}, {0x4, 0xdef8}, {0x1, 0xdef8}}, 0x1, 0},
+ {0x2,(7<<3)|0, {{0x3, 0xdef8}, {0x4, 0xdef8}, {0x1, 0xdef8}, {0x2, 0xdef8}}, 0x2, 0},
+ {0x2,(8<<3)|0, {{0x4, 0xdef8}, {0x1, 0xdef8}, {0x2, 0xdef8}, {0x3, 0xdef8}}, 0x3, 0},
+ {0x2,(9<<3)|0, {{0x1, 0xdef8}, {0x2, 0xdef8}, {0x3, 0xdef8}, {0x4, 0xdef8}}, 0x4, 0},
+ {0x2,(0x0a<<3)|0, {{0x2, 0xdef8}, {0x3, 0xdef8}, {0x4, 0xdef8}, {0x1, 0xdef8}}, 0x6, 0},
+ {0x2,(0x0e<<3)|0, {{0x1, 0xdef8}, {0, 0}, {0, 0}, {0, 0}}, 0, 0},
+ {0x2,(0x0c<<3)|0, {{0x2, 0xdef8}, {0, 0}, {0, 0}, {0, 0}}, 0, 0},
}
};
}
#endif
//extern static void lsi_scsi_init(struct device *dev);
-#if 1
+#if 0
static void print_pci_regs(struct device *dev)
{
uint8_t byte;
// print_mem();
// amd8111_enable_rom();
}
-#if 1
+#if 0
static void vga_fixup(void) {
// we do this right here because:
// - all the hardware is working, and some VGA bioses seem to need
case CONF_PASS_PRE_BOOT:
if (conf->fixup_scsi)
onboard_scsi_fixup();
- if (conf->fixup_vga)
- vga_fixup();
+// if (conf->fixup_vga)
+// vga_fixup();
printk_debug("mainboard fixup pass %d done\r\n",
pass);
break;
static const char productid[12] = "S2850 ";
struct mp_config_table *mc;
+ unsigned char bus_num;
+ unsigned char bus_isa;
+ unsigned char bus_8111_1;
+
mc = (void *)(((char *)v) + SMP_FLOATING_TABLE_LEN);
memset(mc, 0, sizeof(*mc));
mc->reserved = 0;
smp_write_processors(mc, processor_map);
+ {
+ device_t dev;
+
+ /* 8111 */
+ dev = dev_find_slot(1, PCI_DEVFN(0x03,0));
+ if (dev) {
+ bus_8111_1 = pci_read_config8(dev, PCI_SECONDARY_BUS);
+ bus_isa = pci_read_config8(dev, PCI_SUBORDINATE_BUS);
+ bus_isa++;
+ }
+ else {
+ printk_debug("ERROR - could not find PCI 1:03.0, using defaults\n");
+
+ bus_8111_1 = 2;
+ bus_isa = 3;
+ }
+ }
+/*Bus: Bus ID Type*/
+ /* define bus and isa numbers */
+ for(bus_num = 0; bus_num < bus_isa; bus_num++) {
+ smp_write_bus(mc, bus_num, "PCI ");
+ }
+ smp_write_bus(mc, bus_isa, "ISA ");
-/*Bus: Bus ID Type*/
- smp_write_bus(mc, 0, "PCI ");
- smp_write_bus(mc, 1, "PCI ");
- smp_write_bus(mc, 2, "PCI ");
- smp_write_bus(mc, 3, "ISA ");
-
/*I/O APICs: APIC ID Version State Address*/
smp_write_ioapic(mc, 1, 0x11, 0xfec00000);
-/*I/O Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN#
-*/
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, 0x3, 0x1, 0x1, 0x1);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, 0x3, 0x0, 0x1, 0x2);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, 0x3, 0x3, 0x1, 0x3);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, 0x3, 0x4, 0x1, 0x4);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, 0x3, 0x5, 0x1, 0x5);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, 0x3, 0x6, 0x1, 0x6);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, 0x3, 0x7, 0x1, 0x7);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, 0x3, 0x8, 0x1, 0x8);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, 0x3, 0xc, 0x1, 0xc);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, 0x3, 0xd, 0x1, 0xd);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, 0x3, 0xe, 0x1, 0xe);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, 0x3, 0xf, 0x1, 0xf);
-
+/*I/O Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN# */
+
+ smp_write_intsrc(mc, mp_ExtINT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x0, 0x1, 0x0);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x1, 0x1, 0x1);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x0, 0x1, 0x2);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x3, 0x1, 0x3);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x4, 0x1, 0x4);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x6, 0x1, 0x6);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x7, 0x1, 0x7);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x8, 0x1, 0x8);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0xc, 0x1, 0xc);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0xd, 0x1, 0xd);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0xe, 0x1, 0xe);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0xf, 0x1, 0xf);
+
+
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x1, (2<<2)|3, 0x1, 0x13);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x1, (2<<2)|3, 0x1, 0x13);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x2, 0x3, 0x1, 0x13);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x2, 0x34, 0x1, 0x13);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x2, 0x2c, 0x1, 0x12);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x2, 0x38, 0x1, 0x10);
+//On Board AMD USB
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0<<2)|3, 0x1, 0x13);
+
+//On Board ATI Display Adapter
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x0b<<2)|0, 0x1, 0x12);
+
+//Onboard Broadcom 5705 NIC
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x0d<<2)|0, 0x1, 0x13);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x0e<<2)|0, 0x1, 0x10);
+//Onboard SI Serial ATA
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x0c<<2)|0, 0x1, 0x11);
+
+
+//PCI Slot 1
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x03<<2)|0, 0x1, 0x10);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x03<<2)|1, 0x1, 0x11);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x03<<2)|2, 0x1, 0x12);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x03<<2)|3, 0x1, 0x13);
+
+
+//PCI Slot 2
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x06<<2)|0, 0x1, 0x11);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x06<<2)|1, 0x1, 0x12);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x06<<2)|2, 0x1, 0x13);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x06<<2)|3, 0x1, 0x10);
+
+
+//PCI Slot 3
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x07<<2)|0, 0x1, 0x12);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x07<<2)|1, 0x1, 0x13);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x07<<2)|2, 0x1, 0x10);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x07<<2)|3, 0x1, 0x11);
+
+
+//PCI Slot 4
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x08<<2)|0, 0x1, 0x13);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x08<<2)|1, 0x1, 0x10);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x08<<2)|2, 0x1, 0x11);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x08<<2)|3, 0x1, 0x12);
+
+//PCI Slot 5
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x09<<2)|0, 0x1, 0x10);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x09<<2)|1, 0x1, 0x11);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x09<<2)|2, 0x1, 0x12);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x09<<2)|3, 0x1, 0x13);
+//PCI Slot 6
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x0a<<2)|0, 0x1, 0x11);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x0a<<2)|1, 0x1, 0x12);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x0a<<2)|2, 0x1, 0x13);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x0a<<2)|3, 0x1, 0x10);
/*Local Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN#*/
- smp_write_intsrc(mc, mp_ExtINT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, 0x0, 0x0, MP_APIC_ALL, 0x0);
- smp_write_intsrc(mc, mp_NMI, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, 0x0, 0x0, MP_APIC_ALL, 0x1);
+ smp_write_intsrc(mc, mp_ExtINT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x0, MP_APIC_ALL, 0x0);
+ smp_write_intsrc(mc, mp_NMI, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x0, MP_APIC_ALL, 0x1);
/* There is no extension information... */
/* Compute the checksums */
--- /dev/null
+uses HAVE_MP_TABLE
+uses HAVE_PIRQ_TABLE
+uses USE_FALLBACK_IMAGE
+uses LB_CKS_RANGE_START
+uses LB_CKS_RANGE_END
+uses LB_CKS_LOC
+uses MAINBOARD
+uses ARCH
+uses HARD_RESET_BUS
+uses HARD_RESET_DEVICE
+uses HARD_RESET_FUNCTION
+
+#
+#
+###
+### Set all of the defaults for an x86 architecture
+###
+
+#
+#
+###
+### Build the objects we have code for in this directory.
+###
+
+config chip.h
+register "fixup_scsi" = "1"
+register "fixup_vga" = "1"
+
+
+##
+## Move the default LinuxBIOS cmos range off of AMD RTC registers
+##
+default LB_CKS_RANGE_START=49
+default LB_CKS_RANGE_END=122
+default LB_CKS_LOC=123
+
+driver mainboard.o
+#driver si_sata.o
+#driver intel_nic.o
+#object reset.o
+if HAVE_MP_TABLE object mptable.o end
+if HAVE_PIRQ_TABLE object irq_tables.o end
+#
+default HARD_RESET_BUS=1
+default HARD_RESET_DEVICE=5
+default HARD_RESET_FUNCTION=0
+#
+#
+arch i386 end
+
+#
+###
+### Build our 16 bit and 32 bit linuxBIOS entry code
+###
+mainboardinit cpu/i386/entry16.inc
+mainboardinit cpu/i386/entry32.inc
+mainboardinit cpu/i386/bist32.inc
+ldscript /cpu/i386/entry16.lds
+ldscript /cpu/i386/entry32.lds
+
+#
+###
+### Build our reset vector (This is where linuxBIOS is entered)
+###
+if USE_FALLBACK_IMAGE
+ mainboardinit cpu/i386/reset16.inc
+ ldscript /cpu/i386/reset16.lds
+else
+ mainboardinit cpu/i386/reset32.inc
+ ldscript /cpu/i386/reset32.lds
+end
+#
+#### Should this be in the northbridge code?
+mainboardinit arch/i386/lib/cpu_reset.inc
+#
+###
+### Include an id string (For safe flashing)
+###
+mainboardinit arch/i386/lib/id.inc
+ldscript /arch/i386/lib/id.lds
+#
+####
+#### This is the early phase of linuxBIOS startup
+#### Things are delicate and we test to see if we should
+#### failover to another image.
+####
+#option MAX_REBOOT_CNT=2
+if USE_FALLBACK_IMAGE
+ ldscript /arch/i386/lib/failover.lds
+end
+#
+###
+### Setup our mtrrs
+###
+mainboardinit cpu/k8/earlymtrr.inc
+###
+### Only the bootstrap cpu makes it here.
+### Failover if we need to
+###
+#
+if USE_FALLBACK_IMAGE
+ mainboardinit ./failover.inc
+end
+
+#
+#
+###
+### Setup the serial port
+###
+mainboardinit pc80/serial.inc
+mainboardinit arch/i386/lib/console.inc
+mainboardinit cpu/i386/bist32_fail.inc
+#
+####
+#### O.k. We aren't just an intermediary anymore!
+####
+###
+### Romcc output
+###
+makerule ./failover.E
+ depends "$(MAINBOARD)/failover.c"
+ action "$(CPP) -I$(TOP)/src $(ROMCCPPFLAGS) $(CPPFLAGS) $(MAINBOARD)/failover.c > ./failover.E"
+end
+
+makerule ./failover.inc
+ depends "./romcc ./failover.E"
+ action "./romcc -O -o failover.inc --label-prefix=failover ./failover.E"
+end
+
+makerule ./auto.E
+ depends "$(MAINBOARD)/auto.c option_table.h"
+ action "$(CPP) -I$(TOP)/src -I. $(ROMCCPPFLAGS) $(CPPFLAGS) $(MAINBOARD)/auto.c > ./auto.E"
+end
+
+makerule ./auto.inc
+ depends "./romcc ./auto.E"
+ action "./romcc -O2 -mcpu=k8 -o auto.inc --label-prefix=auto ./auto.E"
+end
+
+mainboardinit cpu/k8/enable_mmx_sse.inc
+mainboardinit ./auto.inc
+mainboardinit cpu/k8/disable_mmx_sse.inc
+
+#
+###
+### Include the secondary Configuration files
+###
+dir /pc80
+
+northbridge amd/amdk8 "mc0"
+ pci 0:18.0
+ pci 0:18.0
+ pci 0:18.0
+ pci 0:18.1
+ pci 0:18.2
+ pci 0:18.3
+ southbridge amd/amd8151 "amd8151" link 0
+ pci 0:0.0
+ pci 0:1.0
+ end
+ southbridge amd/amd8111 "amd8111" link 0
+ pci 0:0.0
+ pci 0:1.0 on
+ pci 0:1.1 on
+ pci 0:1.2 on
+ pci 0:1.3 on
+ pci 0:1.5 on
+ pci 0:1.6 off
+ pci 1:0.0 on
+ pci 1:0.1 on
+ pci 1:0.2 on
+ pci 1:1.0 off
+ superio winbond/w83627hf link 1
+ pnp 2e.0 on # Floppy
+ io 0x60 = 0x3f0
+ irq 0x70 = 6
+ drq 0x74 = 2
+ pnp 2e.1 off # Parallel Port
+ io 0x60 = 0x378
+ irq 0x70 = 7
+ pnp 2e.2 on # Com1
+ io 0x60 = 0x3f8
+ irq 0x70 = 4
+ pnp 2e.3 off # Com2
+ io 0x60 = 0x2f8
+ irq 0x70 = 3
+ pnp 2e.5 on # Keyboard
+ io 0x60 = 0x60
+ io 0x62 = 0x64
+ irq 0x70 = 1
+ irq 0x72 = 12
+ pnp 2e.6 off # CIR
+ pnp 2e.7 off # GAME_MIDI_GIPO1
+ pnp 2e.8 off # GPIO2
+ pnp 2e.9 off # GPIO3
+ pnp 2e.a off # ACPI
+ pnp 2e.b on # HW Monitor
+ io 0x60 = 0x290
+ end
+ end
+end
+
+northbridge amd/amdk8 "mc1"
+ pci 0:19.0
+ pci 0:19.0
+ pci 0:19.0
+ pci 0:19.1
+ pci 0:19.2
+ pci 0:19.3
+end
+
+#dir /bioscall
+
+cpu k8 "cpu0"
+ register "up" = "{.chip = &amd8151, .ht_width=16, .ht_speed=600}"
+end
+
+cpu k8 "cpu1"
+end
+
--- /dev/null
+#define ASSEMBLY 1
+
+#include <stdint.h>
+#include <device/pci_def.h>
+#include <arch/io.h>
+#include <device/pnp_def.h>
+#include <arch/romcc_io.h>
+#include <arch/smp/lapic.h>
+#include "option_table.h"
+#include "pc80/mc146818rtc_early.c"
+#include "pc80/serial.c"
+#include "arch/i386/lib/console.c"
+#include "ram/ramtest.c"
+#include "northbridge/amd/amdk8/incoherent_ht.c"
+#include "southbridge/amd/amd8111/amd8111_early_smbus.c"
+#include "northbridge/amd/amdk8/raminit.h"
+#include "cpu/k8/apic_timer.c"
+#include "lib/delay.c"
+#include "cpu/p6/boot_cpu.c"
+#include "northbridge/amd/amdk8/reset_test.c"
+#include "northbridge/amd/amdk8/debug.c"
+#include "northbridge/amd/amdk8/cpu_rev.c"
+#include "superio/winbond/w83627hf/w83627hf_early_serial.c"
+
+#define SERIAL_DEV PNP_DEV(0x2e, W83627HF_SP1)
+
+static void hard_reset(void)
+{
+ set_bios_reset();
+
+ /* enable cf9 */
+ pci_write_config8(PCI_DEV(0, 0x05, 3), 0x41, 0xf1);
+ /* reset */
+ outb(0x0e, 0x0cf9);
+}
+
+static void soft_reset(void)
+{
+ set_bios_reset();
+ pci_write_config8(PCI_DEV(0, 0x05, 0), 0x47, 1);
+}
+
+static void memreset_setup(void)
+{
+ if (is_cpu_pre_c0()) {
+ outb((0 << 7)|(0 << 6)|(0<<5)|(0<<4)|(1<<2)|(0<<0), SMBUS_IO_BASE + 0xc0 + 16); //REVC_MEMRST_EN=0
+ }
+ else {
+ outb((0 << 7)|(0 << 6)|(0<<5)|(0<<4)|(1<<2)|(1<<0), SMBUS_IO_BASE + 0xc0 + 16); //REVC_MEMRST_EN=1
+ }
+ outb((0 << 7)|(0 << 6)|(0<<5)|(0<<4)|(1<<2)|(0<<0), SMBUS_IO_BASE + 0xc0 + 17);
+}
+
+static void memreset(int controllers, const struct mem_controller *ctrl)
+{
+ if (is_cpu_pre_c0()) {
+ udelay(800);
+ outb((0<<7)|(0<<6)|(0<<5)|(0<<4)|(1<<2)|(1<<0), SMBUS_IO_BASE + 0xc0 + 17); //REVB_MEMRST_L=1
+ udelay(90);
+ }
+}
+
+static unsigned int generate_row(uint8_t node, uint8_t row, uint8_t maxnodes)
+{
+ /* Routing Table Node i
+ *
+ * F0: 0x40, 0x44, 0x48, 0x4c, 0x50, 0x54, 0x58, 0x5c
+ * i: 0, 1, 2, 3, 4, 5, 6, 7
+ *
+ * [ 0: 3] Request Route
+ * [0] Route to this node
+ * [1] Route to Link 0
+ * [2] Route to Link 1
+ * [3] Route to Link 2
+ * [11: 8] Response Route
+ * [0] Route to this node
+ * [1] Route to Link 0
+ * [2] Route to Link 1
+ * [3] Route to Link 2
+ * [19:16] Broadcast route
+ * [0] Route to this node
+ * [1] Route to Link 0
+ * [2] Route to Link 1
+ * [3] Route to Link 2
+ */
+
+ uint32_t ret=0x00010101; /* default row entry */
+
+ static const unsigned int rows_2p[2][2] = {
+ { 0x00050101, 0x00010404 },
+ { 0x00010404, 0x00050101 }
+ };
+
+ if(maxnodes>2) {
+ print_debug("this mainboard is only designed for 2 cpus\r\n");
+ maxnodes=2;
+ }
+
+
+ if (!(node>=maxnodes || row>=maxnodes)) {
+ ret=rows_2p[node][row];
+ }
+
+ return ret;
+}
+
+static inline void activate_spd_rom(const struct mem_controller *ctrl)
+{
+ /* nothing to do */
+}
+
+static inline int spd_read_byte(unsigned device, unsigned address)
+{
+ return smbus_read_byte(device, address);
+}
+
+#include "northbridge/amd/amdk8/raminit.c"
+#include "northbridge/amd/amdk8/coherent_ht.c"
+#include "sdram/generic_sdram.c"
+
+#define FIRST_CPU 1
+#define SECOND_CPU 1
+#define TOTAL_CPUS (FIRST_CPU + SECOND_CPU)
+static void main(void)
+{
+ static const struct mem_controller cpu[] = {
+#if FIRST_CPU
+ {
+ .node_id = 0,
+ .f0 = PCI_DEV(0, 0x18, 0),
+ .f1 = PCI_DEV(0, 0x18, 1),
+ .f2 = PCI_DEV(0, 0x18, 2),
+ .f3 = PCI_DEV(0, 0x18, 3),
+ .channel0 = { (0xa<<3)|0, (0xa<<3)|2, 0, 0 },
+ .channel1 = { (0xa<<3)|1, (0xa<<3)|3, 0, 0 },
+ },
+#endif
+#if SECOND_CPU
+ {
+ .node_id = 1,
+ .f0 = PCI_DEV(0, 0x19, 0),
+ .f1 = PCI_DEV(0, 0x19, 1),
+ .f2 = PCI_DEV(0, 0x19, 2),
+ .f3 = PCI_DEV(0, 0x19, 3),
+ .channel0 = { (0xa<<3)|4, (0xa<<3)|6, 0, 0 },
+ .channel1 = { (0xa<<3)|5, (0xa<<3)|7, 0, 0 },
+ },
+#endif
+ };
+
+ int needs_reset;
+ enable_lapic();
+ init_timer();
+ if (cpu_init_detected()) {
+ asm("jmp __cpu_reset");
+ }
+ distinguish_cpu_resets();
+ if (!boot_cpu()) {
+ stop_this_cpu();
+ }
+ w83627hf_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ uart_init();
+ console_init();
+ setup_default_resource_map();
+ needs_reset = setup_coherent_ht_domain();
+ needs_reset |= ht_setup_chain(PCI_DEV(0, 0x18, 0), 0x80);
+ if (needs_reset) {
+ print_info("ht reset -\r\n");
+ soft_reset();
+ }
+#if 0
+ dump_pci_devices();
+#endif
+
+#if 0
+ print_pci_devices();
+#endif
+ enable_smbus();
+#if 0
+ dump_spd_registers(&cpu[0]);
+#endif
+ memreset_setup();
+ sdram_initialize(sizeof(cpu)/sizeof(cpu[0]), cpu);
+
+#if 0
+ dump_pci_devices();
+#endif
+#if 0
+ dump_pci_device(PCI_DEV(0, 0x18, 1));
+#endif
+
+ /* Check all of memory */
+#if 0
+ msr_t msr;
+ msr = rdmsr(TOP_MEM2);
+ print_debug("TOP_MEM2: ");
+ print_debug_hex32(msr.hi);
+ print_debug_hex32(msr.lo);
+ print_debug("\r\n");
+#endif
+/*
+#if 0
+ ram_check(0x00000000, msr.lo+(msr.hi<<32));
+#else
+#if TOTAL_CPUS < 2
+ // Check 16MB of memory @ 0
+ ram_check(0x00000000, 0x00100000);
+#else
+ // Check 16MB of memory @ 2GB
+ ram_check(0x80000000, 0x80100000);
+#endif
+#endif
+*/
+}
--- /dev/null
+extern struct chip_control mainboard_tyan_s2875_control;
+
+struct mainboard_tyan_s2875_config {
+ int fixup_scsi;
+ int fixup_vga;
+};
--- /dev/null
+entries
+
+#start-bit length config config-ID name
+#0 8 r 0 seconds
+#8 8 r 0 alarm_seconds
+#16 8 r 0 minutes
+#24 8 r 0 alarm_minutes
+#32 8 r 0 hours
+#40 8 r 0 alarm_hours
+#48 8 r 0 day_of_week
+#56 8 r 0 day_of_month
+#64 8 r 0 month
+#72 8 r 0 year
+#80 4 r 0 rate_select
+#84 3 r 0 REF_Clock
+#87 1 r 0 UIP
+#88 1 r 0 auto_switch_DST
+#89 1 r 0 24_hour_mode
+#90 1 r 0 binary_values_enable
+#91 1 r 0 square-wave_out_enable
+#92 1 r 0 update_finished_enable
+#93 1 r 0 alarm_interrupt_enable
+#94 1 r 0 periodic_interrupt_enable
+#95 1 r 0 disable_clock_updates
+#96 288 r 0 temporary_filler
+0 384 r 0 reserved_memory
+384 1 e 4 boot_option
+385 1 e 4 last_boot
+386 1 e 1 ECC_memory
+388 4 r 0 reboot_bits
+392 3 e 5 baud_rate
+395 1 e 1 hw_scrubber
+396 1 e 1 interleave_chip_selects
+397 2 e 8 max_mem_clock
+400 1 e 1 power_on_after_fail
+412 4 e 6 debug_level
+416 4 e 7 boot_first
+420 4 e 7 boot_second
+424 4 e 7 boot_third
+428 4 h 0 boot_index
+432 8 h 0 boot_countdown
+440 4 e 9 slow_cpu
+444 1 e 1 nmi
+728 256 h 0 user_data
+984 16 h 0 check_sum
+# Reserve the extended AMD configuration registers
+1000 24 r 0 reserved_memory
+
+
+
+enumerations
+
+#ID value text
+1 0 Disable
+1 1 Enable
+2 0 Enable
+2 1 Disable
+4 0 Fallback
+4 1 Normal
+5 0 115200
+5 1 57600
+5 2 38400
+5 3 19200
+5 4 9600
+5 5 4800
+5 6 2400
+5 7 1200
+6 6 Notice
+6 7 Info
+6 8 Debug
+6 9 Spew
+7 0 Network
+7 1 HDD
+7 2 Floppy
+7 8 Fallback_Network
+7 9 Fallback_HDD
+7 10 Fallback_Floppy
+#7 3 ROM
+8 0 200Mhz
+8 1 166Mhz
+8 2 133Mhz
+8 3 100Mhz
+9 0 off
+9 1 87.5%
+9 2 75.0%
+9 3 62.5%
+9 4 50.0%
+9 5 37.5%
+9 6 25.0%
+9 7 12.5%
+
+checksums
+
+checksum 392 983 984
+
+
--- /dev/null
+#define ASSEMBLY 1
+#include <stdint.h>
+#include <device/pci_def.h>
+#include <device/pci_ids.h>
+#include <arch/io.h>
+#include <arch/romcc_io.h>
+#include <arch/smp/lapic.h>
+#include "pc80/mc146818rtc_early.c"
+#include "southbridge/amd/amd8111/amd8111_enable_rom.c"
+#include "northbridge/amd/amdk8/early_ht.c"
+#include "cpu/p6/boot_cpu.c"
+#include "northbridge/amd/amdk8/reset_test.c"
+
+#define HAVE_REGPARM_SUPPORT 0
+#if HAVE_REGPARM_SUPPORT
+static unsigned long main(unsigned long bist)
+{
+#else
+static void main(void)
+{
+ unsigned long bist = 0;
+#endif
+ /* Make cerain my local apic is useable */
+ enable_lapic();
+
+ /* Is this a cpu only reset? */
+ if (cpu_init_detected()) {
+ if (last_boot_normal()) {
+ goto normal_image;
+ } else {
+ goto cpu_reset;
+ }
+ }
+ /* Is this a secondary cpu? */
+ if (!boot_cpu()) {
+ if (last_boot_normal()) {
+ goto normal_image;
+ } else {
+ goto fallback_image;
+ }
+ }
+
+
+ /* Nothing special needs to be done to find bus 0 */
+ /* Allow the HT devices to be found */
+ enumerate_ht_chain();
+
+ /* Setup the 8111 */
+ amd8111_enable_rom();
+
+ /* Is this a deliberate reset by the bios */
+ if (bios_reset_detected() && last_boot_normal()) {
+ goto normal_image;
+ }
+ /* This is the primary cpu how should I boot? */
+ else if (do_normal_boot()) {
+ goto normal_image;
+ }
+ else {
+ goto fallback_image;
+ }
+ normal_image:
+ asm("jmp __normal_image"
+ : /* outputs */
+ : "a" (bist) /* inputs */
+ : /* clobbers */
+ );
+ cpu_reset:
+ asm("jmp __cpu_reset"
+ : /* outputs */
+ : "a"(bist) /* inputs */
+ : /* clobbers */
+ );
+ fallback_image:
+#if HAVE_REGPARM_SUPPORT
+ return bist;
+#else
+ return;
+#endif
+}
--- /dev/null
+/* This file was generated by getpir.c, do not modify!
+ (but if you do, please run checkpir on it to verify)
+ Contains the IRQ Routing Table dumped directly from your memory , wich BIOS sets up
+
+ Documentation at : http://www.microsoft.com/hwdev/busbios/PCIIRQ.HTM
+*/
+
+#include <arch/pirq_routing.h>
+
+const struct irq_routing_table intel_irq_routing_table = {
+ PIRQ_SIGNATURE, /* u32 signature */
+ PIRQ_VERSION, /* u16 version */
+ 32+16*13, /* there can be total 13 devices on the bus */
+ 1, /* Where the interrupt router lies (bus) */
+ (5<<3)|3, /* Where the interrupt router lies (dev) */
+ 0, /* IRQs devoted exclusively to PCI usage */
+ 0x1022, /* Vendor */
+ 0x746b, /* Device */
+ 0, /* Crap (miniport) */
+ { 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 }, /* u8 rfu[11] */
+ 0xcf, /* u8 checksum , this hase to set to some value that would give 0 after the sum of all bytes for this structure (including checksum) */
+ {
+ {1,(5<<3)|0, {{0x1, 0xdef8}, {0x2, 0xdef8}, {0x3, 0xdef8}, {0x4, 0xdef8}}, 0, 0},
+ {0x3,0, {{0, 0}, {0, 0}, {0, 0}, {0x4, 0xdef8}}, 0, 0},
+ {1,(1<<3)|0, {{0x1, 0xdef8}, {0x2, 0xdef8}, {0, 0}, {0, 0}}, 0, 0},
+ {0x2,0, {{0x1, 0xdef8}, {0x2, 0xdef8}, {0, 0}, {0, 0}}, 0, 0},
+ {0x3,(4<<3)|0, {{0x1, 0xdef8}, {0x2, 0xdef8}, {0x3, 0xdef8}, {0x4, 0xdef8}}, 0x5, 0},
+ {0x3,(7<<3)|0, {{0x4, 0xdef8}, {0x1, 0xdef8}, {0x2, 0xdef8}, {0x3, 0xdef8}}, 0x4, 0},
+ {0x3,(6<<3)|0, {{0x3, 0xdef8}, {0x4, 0xdef8}, {0x1, 0xdef8}, {0x2, 0xdef8}}, 0x1, 0},
+ {0x3,(8<<3)|0, {{0x2, 0xdef8}, {0x3, 0xdef8}, {0x4, 0xdef8}, {0x1, 0xdef8}}, 0x2, 0},
+ {0x3,(9<<3)|0, {{0x1, 0xdef8}, {0x2, 0xdef8}, {0x3, 0xdef8}, {0x4, 0xdef8}}, 0x3, 0},
+ {0x3,(5<<3)|0, {{0x4, 0xdef8}, {0, 0}, {0, 0}, {0, 0}}, 0, 0},
+ {0x3,(3<<3)|0, {{0x3, 0xdef8}, {0, 0}, {0, 0}, {0, 0}}, 0, 0},
+ {0x3,(0x0a<<3)|0, {{0x2, 0xdef8}, {0, 0}, {0, 0}, {0, 0}}, 0, 0},
+ {0x3,(0x0b<<3)|0, {{0x2, 0xdef8}, {0x3, 0xdef8}, {0x4, 0xdef8}, {0, 0}}, 0, 0},
+ }
+};
--- /dev/null
+#include <console/console.h>
+#include <device/device.h>
+#include <device/chip.h>
+#include <device/pci.h>
+#include <device/pci_ids.h>
+#include <device/pci_ops.h>
+#include "../../../northbridge/amd/amdk8/northbridge.h"
+#include "chip.h"
+//#include <part/mainboard.h>
+unsigned long initial_apicid[CONFIG_MAX_CPUS] =
+{
+ 0,1
+};
+#if 0
+static void fixup_lsi_53c1030(struct device *pdev)
+{
+// uint8_t byte;
+ uint16_t word;
+
+ byte = 1;
+ pci_write_config8(pdev, 0xff, byte);
+ // Set the device id
+// pci_write_config_word(pdev, PCI_DEVICE_ID, PCI_DEVICE_ID_LSILOGIC_53C1030);
+ // Set the subsytem vendor id
+// pci_write_config16(pdev, PCI_SUBSYSTEM_VENDOR_ID, PCI_VENDOR_ID_TYAN);
+ word = 0x10f1;
+ pci_write_config16(pdev, PCI_SUBSYSTEM_VENDOR_ID, word);
+ // Set the subsytem id
+ word = 0x2880;
+ pci_write_config16(pdev, PCI_SUBSYSTEM_ID, word);
+ // Disable writes to the device id
+ byte = 0;
+ pci_write_config8(pdev, 0xff, byte);
+
+// lsi_scsi_init(pdev);
+
+}
+#endif
+//extern static void lsi_scsi_init(struct device *dev);
+#if 0
+static void print_pci_regs(struct device *dev)
+{
+ uint8_t byte;
+ int i;
+
+ for(i=0;i<256;i++) {
+ byte = pci_read_config8(dev, i);
+
+ if((i%16)==0) printk_debug("\n%02x:",i);
+ printk_debug(" %02x",byte);
+ }
+ printk_debug("\n");
+
+// pci_write_config8(dev, 0x4, byte);
+
+}
+#endif
+#if 0
+static void print_mem(void)
+{
+ int i;
+ int low_1MB = 0;
+ for(i=low_1MB;i<low_1MB+1024*4;i++) {
+ if((i%16)==0) printk_debug("\n %08x:",i);
+ printk_debug(" %02x ",(unsigned char)*((unsigned char *)i));
+ }
+
+ for(i=low_1MB;i<low_1MB+1024*4;i++) {
+ if((i%16)==0) printk_debug("\n %08x:",i);
+ printk_debug(" %c ",(unsigned char)*((unsigned char *)i));
+ }
+ }
+#endif
+#if 0
+static void amd8111_enable_rom(void)
+{
+ uint8_t byte;
+ struct device *dev;
+
+ /* Enable 4MB rom access at 0xFFC00000 - 0xFFFFFFFF */
+ /* Locate the amd8111 */
+ dev = dev_find_device(0x1022, 0x7468, 0);
+
+ /* Set the 4MB enable bit bit */
+ byte = pci_read_config8(dev, 0x43);
+ byte |= 0x80;
+ pci_write_config8(dev, 0x43, byte);
+}
+#endif
+#if 0
+static void onboard_scsi_fixup(void)
+{
+ struct device *dev;
+#if 1
+ unsigned char i,j,k;
+
+ for(i=0;i<=6;i++) {
+ for(j=0;j<=0x1f;j++) {
+ for (k=0;k<=6;k++){
+ dev = dev_find_slot(i, PCI_DEVFN(j, k));
+ if (dev) {
+ printk_debug("%02x:%02x:%02x",i,j,k);
+ print_pci_regs(dev);
+ }
+ }
+ }
+ }
+#endif
+
+
+#if 0
+ dev = dev_find_device(PCI_VENDOR_ID_LSI_LOGIC, PCI_DEVICE_ID_LSI_53C1030,0);
+ if(!dev) {
+ printk_info("LSI_SCSI_FW_FIXUP: No Device Found!");
+ return;
+ }
+
+ lsi_scsi_init(dev);
+#endif
+// print_mem();
+// amd8111_enable_rom();
+}
+#endif
+#if 0
+static void vga_fixup(void) {
+ // we do this right here because:
+ // - all the hardware is working, and some VGA bioses seem to need
+ // that
+ // - we need page 0 below for linuxbios tables.
+#if CONFIG_REALMODE_IDT == 1
+ printk_debug("INSTALL REAL-MODE IDT\n");
+ setup_realmode_idt();
+#endif
+#if CONFIG_VGABIOS == 1
+ printk_debug("DO THE VGA BIOS\n");
+ do_vgabios(0x0600);
+ post_code(0x93);
+#endif
+
+}
+
+#endif
+
+
+static void
+enable(struct chip *chip, enum chip_pass pass)
+{
+
+ struct mainboard_tyan_s2875_config *conf =
+ (struct mainboard_tyan_s2875_config *)chip->chip_info;
+
+ switch (pass) {
+ default: break;
+// case CONF_PASS_PRE_CONSOLE:
+// case CONF_PASS_PRE_PCI:
+// case CONF_PASS_POST_PCI:
+ case CONF_PASS_PRE_BOOT:
+// if (conf->fixup_scsi)
+ // onboard_scsi_fixup();
+// if (conf->fixup_vga)
+// vga_fixup();
+ printk_debug("mainboard fixup pass %d done\r\n",
+ pass);
+ break;
+ }
+
+}
+void final_mainboard_fixup(void)
+{
+#if 0
+ enable_ide_devices();
+#endif
+}
+static struct device_operations mainboard_operations = {
+ .read_resources = root_dev_read_resources,
+ .set_resources = root_dev_set_resources,
+ .enable_resources = enable_childrens_resources,
+ .init = 0,
+ .scan_bus = amdk8_scan_root_bus,
+ .enable = 0,
+};
+
+static void enumerate(struct chip *chip)
+{
+ struct chip *child;
+ dev_root.ops = &mainboard_operations;
+ chip->dev = &dev_root;
+ chip->bus = 0;
+ for(child = chip->children; child; child = child->next) {
+ child->bus = &dev_root.link[0];
+ }
+}
+struct chip_control mainboard_tyan_s2875_control = {
+ .enable = enable,
+ .enumerate = enumerate,
+ .name = "Tyan s2875 mainboard ",
+};
--- /dev/null
+#include <console/console.h>
+#include <arch/smp/mpspec.h>
+#include <device/pci.h>
+#include <string.h>
+#include <stdint.h>
+
+void *smp_write_config_table(void *v, unsigned long * processor_map)
+{
+ static const char sig[4] = "PCMP";
+ static const char oem[8] = "TYAN ";
+ static const char productid[12] = "S2875 ";
+ struct mp_config_table *mc;
+
+ unsigned char bus_num;
+ unsigned char bus_isa;
+ unsigned char bus_8111_1;
+ unsigned char bus_8151_1;
+
+
+ mc = (void *)(((char *)v) + SMP_FLOATING_TABLE_LEN);
+ memset(mc, 0, sizeof(*mc));
+
+ memcpy(mc->mpc_signature, sig, sizeof(sig));
+ mc->mpc_length = sizeof(*mc); /* initially just the header */
+ mc->mpc_spec = 0x04;
+ mc->mpc_checksum = 0; /* not yet computed */
+ memcpy(mc->mpc_oem, oem, sizeof(oem));
+ memcpy(mc->mpc_productid, productid, sizeof(productid));
+ mc->mpc_oemptr = 0;
+ mc->mpc_oemsize = 0;
+ mc->mpc_entry_count = 0; /* No entries yet... */
+ mc->mpc_lapic = LAPIC_ADDR;
+ mc->mpe_length = 0;
+ mc->mpe_checksum = 0;
+ mc->reserved = 0;
+
+ smp_write_processors(mc, processor_map);
+
+ {
+ device_t dev;
+
+ /* 8111 */
+ dev = dev_find_slot(1, PCI_DEVFN(0x04,0));
+ if (dev) {
+ bus_8111_1 = pci_read_config8(dev, PCI_SECONDARY_BUS);
+ bus_isa = pci_read_config8(dev, PCI_SUBORDINATE_BUS);
+ bus_isa++;
+ printk_debug("bus_isa=%d\n",bus_isa);
+ }
+ else {
+ printk_debug("ERROR - could not find PCI 1:03.0, using defaults\n");
+
+ bus_8111_1 = 3;
+ bus_isa = 4;
+ }
+ /* 8151 */
+ dev = dev_find_slot(1, PCI_DEVFN(0x02,0));
+ if (dev) {
+ bus_8151_1 = pci_read_config8(dev, PCI_SECONDARY_BUS);
+ printk_debug("bus_8151_1=%d\n",bus_8151_1);
+
+ }
+ else {
+ printk_debug("ERROR - could not find PCI 1:02.0, using defaults\n");
+
+ bus_8151_1 = 2;
+ }
+
+
+ }
+
+
+
+/*Bus: Bus ID Type*/
+ /* define bus and isa numbers */
+ for(bus_num = 0; bus_num < bus_isa; bus_num++) {
+ smp_write_bus(mc, bus_num, "PCI ");
+ }
+ smp_write_bus(mc, bus_isa, "ISA ");
+
+/*I/O APICs: APIC ID Version State Address*/
+ smp_write_ioapic(mc, 2, 0x11, 0xfec00000);
+
+/*I/O Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN#
+*/ smp_write_intsrc(mc, mp_ExtINT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x0, 0x2, 0x0);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x1, 0x2, 0x1);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x0, 0x2, 0x2);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x3, 0x2, 0x3);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x4, 0x2, 0x4);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x6, 0x2, 0x6);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x7, 0x2, 0x7);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x8, 0x2, 0x8);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0xc, 0x2, 0xc);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0xd, 0x2, 0xd);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0xe, 0x2, 0xe);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0xf, 0x2, 0xf);
+
+
+//??? What
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x1, (5<<2)|3, 0x2, 0x13);
+//Onboard AMD AC97 Audio ???
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x1, (5<<2)|1, 0x2, 0x11);
+// Onboard AMD USB
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0<<2)|3, 0x2, 0x13);
+
+// AGP Display Adapter
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8151_1, 0x0, 0x2, 0x10);
+
+// Onboard Serial ATA
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x05<<2)|0, 0x2, 0x13);
+//Onboard Firewire
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x0a<<2)|0, 0x2, 0x11);
+//Onboard Broadcom NIC
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x03<<2)|0, 0x2, 0x12);
+
+//Onboard VIA USB 1.1
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x0b<<2)|0, 0x2, 0x11);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x0b<<2)|1, 0x2, 0x12);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x0b<<2)|2, 0x2, 0x13);
+
+//Slot 1
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x06<<2)|0, 0x2, 0x12);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x06<<2)|1, 0x2, 0x13);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x06<<2)|2, 0x2, 0x10); //
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x06<<2)|3, 0x2, 0x11); //
+
+//Slot 2
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x08<<2)|0, 0x2, 0x11);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x08<<2)|1, 0x2, 0x12);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x08<<2)|2, 0x2, 0x13); //
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x08<<2)|3, 0x2, 0x10); //
+
+//Slot 3
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x09<<2)|0, 0x2, 0x10);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x09<<2)|1, 0x2, 0x11);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x09<<2)|2, 0x2, 0x12); //
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x09<<2)|3, 0x2, 0x13); //
+
+//Slot 4
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x07<<2)|0, 0x2, 0x13);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x07<<2)|1, 0x2, 0x10);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x07<<2)|2, 0x2, 0x11); //
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x07<<2)|3, 0x2, 0x12); //
+
+
+//Slot 5
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x04<<2)|0, 0x2, 0x10);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x04<<2)|1, 0x2, 0x11);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x04<<2)|2, 0x2, 0x12); //
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x04<<2)|3, 0x2, 0x13); //
+
+
+
+/*Local Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN#*/
+ smp_write_intsrc(mc, mp_ExtINT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x0, MP_APIC_ALL, 0x0);
+ smp_write_intsrc(mc, mp_NMI, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x0, MP_APIC_ALL, 0x1);
+ /* There is no extension information... */
+
+ /* Compute the checksums */
+ mc->mpe_checksum = smp_compute_checksum(smp_next_mpc_entry(mc), mc->mpe_length);
+ mc->mpc_checksum = smp_compute_checksum(mc, mc->mpc_length);
+ printk_debug("Wrote the mp table end at: %p - %p\n",
+ mc, smp_next_mpe_entry(mc));
+ return smp_next_mpe_entry(mc);
+}
+
+unsigned long write_smp_table(unsigned long addr, unsigned long *processor_map)
+{
+ void *v;
+ v = smp_write_floating_table(addr);
+ return (unsigned long)smp_write_config_table(v, processor_map);
+}
driver mainboard.o
-driver lsi_scsi.o
+dir ../common/lsi_scsi
#driver adaptec_scsi.o
#driver promise_sata.o
#driver intel_nic.o
end
makerule ./auto.inc
depends "./romcc ./auto.E"
- action "./romcc -O -mcpu=k8 -o auto.inc --label-prefix=auto ./auto.E"
-# action "./romcc -mcpu=k8 -O ./auto.E > auto.inc"
+ action "./romcc -O2 -mcpu=k8 -o auto.inc --label-prefix=auto ./auto.E"
end
mainboardinit cpu/k8/enable_mmx_sse.inc
mainboardinit ./auto.inc
set_bios_reset();
pci_write_config8(PCI_DEV(0, 0x04, 0), 0x47, 1);
}
-#define REV_B_RESET 0
static void memreset_setup(void)
{
-#if REV_B_RESET==1
+ if (is_cpu_pre_c0()) {
outb((0 << 7)|(0 << 6)|(0<<5)|(0<<4)|(1<<2)|(0<<0), SMBUS_IO_BASE + 0xc0 + 16); //REVC_MEMRST_EN=0
-#else
+ }
+ else {
outb((0 << 7)|(0 << 6)|(0<<5)|(0<<4)|(1<<2)|(1<<0), SMBUS_IO_BASE + 0xc0 + 16); //REVC_MEMRST_EN=1
-#endif
+ }
outb((0 << 7)|(0 << 6)|(0<<5)|(0<<4)|(1<<2)|(0<<0), SMBUS_IO_BASE + 0xc0 + 17);
}
static void memreset(int controllers, const struct mem_controller *ctrl)
{
+ if (is_cpu_pre_c0()) {
udelay(800);
-#if REV_B_RESET==1
outb((0<<7)|(0<<6)|(0<<5)|(0<<4)|(1<<2)|(1<<0), SMBUS_IO_BASE + 0xc0 + 17); //REVB_MEMRST_L=1
-#endif
udelay(90);
+ }
}
static unsigned int generate_row(uint8_t node, uint8_t row, uint8_t maxnodes)
}
/* include mainboard specific ht code */
-#include "hypertransport.c"
+//#include "hypertransport.c"
#include "northbridge/amd/amdk8/raminit.c"
#include "northbridge/amd/amdk8/coherent_ht.c"
needs_reset = setup_coherent_ht_domain();
needs_reset |= ht_setup_chain(PCI_DEV(0, 0x18, 0), 0x80);
if (needs_reset) {
- print_info("ht reset -\r\t");
+ print_info("ht reset -\r\n");
soft_reset();
}
#driver adaptec_scsi.o
#driver si_sata.o
#driver intel_nic.o
-#driver broadcom_nic.o
+#dir ../drivers/broadcom_nic_ipmi
+dir ../drivers/ati_graph
#object reset.o
if HAVE_MP_TABLE object mptable.o end
if HAVE_PIRQ_TABLE object irq_tables.o end
###
### Romcc output
###
-#makerule ./failover.E dep "$(MAINBOARD)/failover.c" act "$(CPP) -I$(TOP)/src $(CPPFLAGS) $(MAINBOARD)/failover.c > ./failever.E"
-#makerule ./failover.inc dep "./romcc ./failover.E" act "./romcc -O ./failover.E > failover.inc"
-#mainboardinit .failover.inc
makerule ./failover.E
depends "$(MAINBOARD)/failover.c"
makerule ./failover.inc
depends "./romcc ./failover.E"
- action "./romcc -O -o failover.inc --label-prefix=failover ./failover.E"end
+ action "./romcc -O2 -o failover.inc --label-prefix=failover ./failover.E"end
makerule ./auto.E
depends "$(MAINBOARD)/auto.c option_table.h"
end
makerule ./auto.inc
depends "./romcc ./auto.E"
- action "./romcc -O -mcpu=k8 -o auto.inc --label-prefix=auto ./auto.E"
-# action "./romcc -mcpu=k8 -O ./auto.E > auto.inc"
+ action "./romcc -O2 -mcpu=k8 -o auto.inc --label-prefix=auto ./auto.E"
end
mainboardinit cpu/k8/enable_mmx_sse.inc
mainboardinit ./auto.inc
###
### Include the secondary Configuration files
###
+
+dir /pc80
+
northbridge amd/amdk8 "mc0"
pci 0:18.0
pci 0:18.0
pci 1:0.1 on
pci 1:0.2 on
pci 1:1.0 off
- superio winbond/w83627hf link 1
- pnp 2e.0 off # Floppy
- io 0x60 = 0x3f0
- irq 0x70 = 6
- drq 0x74 = 2
- pnp 2e.1 off # Parallel Port
- io 0x60 = 0x378
- irq 0x70 = 7
- pnp 2e.2 on # Com1
- io 0x60 = 0x3f8
- irq 0x70 = 4
- pnp 2e.3 off # Com2
- io 0x60 = 0x2f8
- irq 0x70 = 3
- pnp 2e.5 on # Keyboard
- io 0x60 = 0x60
- io 0x62 = 0x64
- irq 0x70 = 1
- pnp 2e.6 off # CIR
- pnp 2e.7 off # GAME_MIDI_GIPO1
- pnp 2e.8 off # GPIO2
- pnp 2e.9 off # GPIO3
- pnp 2e.a off # ACPI
- pnp 2e.b off # HW Monitor
- end
+# superio winbond/w83627hf link 1
+# pnp 2e.0 on # Floppy
+# io 0x60 = 0x3f0
+# irq 0x70 = 6
+# drq 0x74 = 2
+# pnp 2e.1 off # Parallel Port
+# io 0x60 = 0x378
+# irq 0x70 = 7
+# pnp 2e.2 on # Com1
+# io 0x60 = 0x3f8
+# irq 0x70 = 4
+# pnp 2e.3 off # Com2
+# io 0x60 = 0x2f8
+# irq 0x70 = 3
+# pnp 2e.5 on # Keyboard
+# io 0x60 = 0x60
+# io 0x62 = 0x64
+# irq 0x70 = 1
+# irq 0x72 = 12
+# pnp 2e.6 off # CIR
+# pnp 2e.7 off # GAME_MIDI_GIPO1
+# pnp 2e.8 off # GPIO2
+# pnp 2e.9 off # GPIO3
+# pnp 2e.a off # ACPI
+# pnp 2e.b on # HW Monitor
+# io 0x60 = 0x290
+# end
end
end
end
-dir /pc80
#dir /bioscall
cpu k8 "cpu0"
register "up" = "{.chip = &amd8131, .ht_width=16, .ht_speed=600}"
pci_write_config8(PCI_DEV(0, 0x04, 0), 0x47, 1);
}
-#define REV_B_RESET 0
static void memreset_setup(void)
{
-#if REV_B_RESET==1
+ if (is_cpu_pre_c0()) {
outb((0 << 7)|(0 << 6)|(0<<5)|(0<<4)|(1<<2)|(0<<0), SMBUS_IO_BASE + 0xc0 + 16); //REVC_MEMRST_EN=0
-#else
+ }
+ else {
outb((0 << 7)|(0 << 6)|(0<<5)|(0<<4)|(1<<2)|(1<<0), SMBUS_IO_BASE + 0xc0 + 16); //REVC_MEMRST_EN=1
-#endif
+ }
outb((0 << 7)|(0 << 6)|(0<<5)|(0<<4)|(1<<2)|(0<<0), SMBUS_IO_BASE + 0xc0 + 17);
}
static void memreset(int controllers, const struct mem_controller *ctrl)
{
+ if (is_cpu_pre_c0()) {
udelay(800);
-#if REV_B_RESET==1
outb((0<<7)|(0<<6)|(0<<5)|(0<<4)|(1<<2)|(1<<0), SMBUS_IO_BASE + 0xc0 + 17); //REVB_MEMRST_L=1
-#endif
udelay(90);
+ }
}
static unsigned int generate_row(uint8_t node, uint8_t row, uint8_t maxnodes)
needs_reset = setup_coherent_ht_domain();
needs_reset |= ht_setup_chain(PCI_DEV(0, 0x18, 0), 0xc0);
if (needs_reset) {
- print_info("ht reset -\r\t");
+ print_info("ht reset -\r\n");
soft_reset();
}
0x746b, /* Device */
0, /* Crap (miniport) */
{ 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 }, /* u8 rfu[11] */
- 0x3d, /* u8 checksum , this hase to set to some value that would give 0 after the sum of all bytes for this structure (including checksum) */
+ 0x66, /* u8 checksum , this hase to set to some value that would give 0 after the sum of all bytes for this structure (including checksum) */
{
{1,(4<<3)|0, {{0x1, 0xdef8}, {0x2, 0xdef8}, {0x3, 0xdef8}, {0x4, 0xdef8}}, 0, 0},
{0x4,0, {{0, 0}, {0, 0}, {0, 0}, {0x4, 0xdef8}}, 0, 0},
}
#endif
//extern static void lsi_scsi_init(struct device *dev);
-#if 1
+#if 0
static void print_pci_regs(struct device *dev)
{
uint8_t byte;
// case CONF_PASS_PRE_PCI:
// case CONF_PASS_POST_PCI:
case CONF_PASS_PRE_BOOT:
- if (conf->fixup_scsi)
- onboard_scsi_fixup();
+// if (conf->fixup_scsi)
+ // onboard_scsi_fixup();
// if (conf->fixup_vga)
// vga_fixup();
- printk_debug("mainboard fixup pass %d done\r\n",
- pass);
+// printk_debug("mainboard fixup pass %d done\r\n",pass);
break;
}
smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_1, (8<<2)|3, 0x3, 0x2);//
-//On Board NIC and LSI scsi
+//On Board NIC and adaptec scsi
smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_1, (9<<2)|0, 0x3, 0x0);
smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_1, (9<<2)|1, 0x3, 0x1);
smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_1, (0xa<<2)|0, 0x3, 0x0);
#define REV_B_RESET 0
static void memreset_setup(void)
{
-#if REV_B_RESET==1
+ if (is_cpu_pre_c0()) {
outb((0 << 7)|(0 << 6)|(0<<5)|(0<<4)|(1<<2)|(0<<0), SMBUS_IO_BASE + 0xc0 + 16); //REVC_MEMRST_EN=0
-#else
+ }
+ else {
outb((0 << 7)|(0 << 6)|(0<<5)|(0<<4)|(1<<2)|(1<<0), SMBUS_IO_BASE + 0xc0 + 16); //REVC_MEMRST_EN=1
-#endif
+ }
outb((0 << 7)|(0 << 6)|(0<<5)|(0<<4)|(1<<2)|(0<<0), SMBUS_IO_BASE + 0xc0 + 17);
}
static void memreset(int controllers, const struct mem_controller *ctrl)
{
+ if (is_cpu_pre_c0()) {
udelay(800);
-#if REV_B_RESET==1
outb((0<<7)|(0<<6)|(0<<5)|(0<<4)|(1<<2)|(1<<0), SMBUS_IO_BASE + 0xc0 + 17); //REVB_MEMRST_L=1
-#endif
udelay(90);
+ }
}
// case CONF_PASS_PRE_PCI:
case CONF_PASS_POST_PCI:
case CONF_PASS_PRE_BOOT:
- if (conf->fixup_scsi)
- onboard_scsi_fixup();
+// if (conf->fixup_scsi)
+// onboard_scsi_fixup();
// if (conf->fixup_vga)
// vga_fixup();
- printk_debug("mainboard fixup pass %d done\r\n",
- pass);
+// printk_debug("mainboard fixup pass %d done\r\n",pass);
break;
}
-#define ASSEMBLY 1
+#define ASSEMBLY 1
+
#include <stdint.h>
#include <device/pci_def.h>
#include <arch/io.h>
static void memreset_setup(void)
{
- if (is_cpu_pre_c0()) {
- outb((0 << 7)|(0 << 6)|(0<<5)|(0<<4)|(1<<2)|(0<<0), SMBUS_IO_BASE + 0xc0 + 17);
- outb((0 << 7)|(0 << 6)|(0<<5)|(0<<4)|(1<<2)|(0<<0), SMBUS_IO_BASE + 0xc0 + 16); //REVC_MEMRST_EN=0
- } else {
- outb((0 << 7)|(0 << 6)|(0<<5)|(0<<4)|(1<<2)|(1<<0), SMBUS_IO_BASE + 0xc0 + 16); //REVC_MEMRST_EN=1
- }
+ if (is_cpu_pre_c0()) {
+ outb((0 << 7)|(0 << 6)|(0<<5)|(0<<4)|(1<<2)|(0<<0), SMBUS_IO_BASE + 0xc0 + 16); //REVC_MEMRST_EN=0
+ }
+ else {
+ outb((0 << 7)|(0 << 6)|(0<<5)|(0<<4)|(1<<2)|(1<<0), SMBUS_IO_BASE + 0xc0 + 16); //REVC_MEMRST_EN=1
+ }
+ outb((0 << 7)|(0 << 6)|(0<<5)|(0<<4)|(1<<2)|(0<<0), SMBUS_IO_BASE + 0xc0 + 17);
}
static void memreset(int controllers, const struct mem_controller *ctrl)
{
- if (is_cpu_pre_c0()) {
- udelay(800);
- outb((0<<7)|(0<<6)|(0<<5)|(0<<4)|(1<<2)|(1<<0), SMBUS_IO_BASE + 0xc0 + 17); //REVB_MEMRST_L=1
- udelay(90);
- }
+ if (is_cpu_pre_c0()) {
+ udelay(800);
+ outb((0<<7)|(0<<6)|(0<<5)|(0<<4)|(1<<2)|(1<<0), SMBUS_IO_BASE + 0xc0 + 17); //REVB_MEMRST_L=1
+ udelay(90);
+ }
}
static unsigned int generate_row(uint8_t node, uint8_t row, uint8_t maxnodes)
* [3] Route to Link 2
*/
- uint32_t ret = 0x00010101; /* default row entry */
+ uint32_t ret=0x00010101; /* default row entry */
static const unsigned int rows_2p[2][2] = {
{ 0x00050101, 0x00010404 },
{ 0x00010404, 0x00050101 }
};
- if (maxnodes > 2) {
+ if(maxnodes>2) {
print_debug("this mainboard is only designed for 2 cpus\r\n");
- maxnodes = 2;
+ maxnodes=2;
}
- if (!(node >= maxnodes || row >= maxnodes)) {
- ret = rows_2p[node][row];
+
+ if (!(node>=maxnodes || row>=maxnodes)) {
+ ret=rows_2p[node][row];
}
return ret;
#endif
};
+#if 1
static const struct ht_chain ht_c[] = {
{
.udev = PCI_DEV(0, 0x18, 0),
- /* LDT2 */
.upos = 0xc0,
.devreg = 0xe0,
},
.devreg = 0xe4,
},
};
- int needs_reset;
+#endif
+ int needs_reset;
enable_lapic();
init_timer();
-
if (cpu_init_detected()) {
asm("jmp __cpu_reset");
}
-
distinguish_cpu_resets();
if (!boot_cpu()) {
stop_this_cpu();
}
-
w83627hf_enable_serial(SERIAL_DEV, TTYS0_BASE);
uart_init();
console_init();
-
setup_s2885_resource_map();
needs_reset = setup_coherent_ht_domain();
+#if 0
+ needs_reset |= ht_setup_chain(PCI_DEV(0, 0x18, 0), 0xc0);
+#else
needs_reset |= ht_setup_chains(ht_c, sizeof(ht_c)/sizeof(ht_c[0]));
+#endif
if (needs_reset) {
print_info("ht reset -\r\n");
soft_reset();
dump_pci_devices();
#endif
-
#if 0
print_pci_devices();
#endif
-
enable_smbus();
-
#if 0
dump_spd_registers(&cpu[0]);
#endif
-
memreset_setup();
sdram_initialize(sizeof(cpu)/sizeof(cpu[0]), cpu);
#if 0
dump_pci_devices();
+#endif
+#if 0
dump_pci_device(PCI_DEV(0, 0x18, 1));
#endif
print_debug_hex32(msr.hi);
print_debug_hex32(msr.lo);
print_debug("\r\n");
+#endif
+/*
+#if 0
ram_check(0x00000000, msr.lo+(msr.hi<<32));
+#else
#if TOTAL_CPUS < 2
// Check 16MB of memory @ 0
ram_check(0x00000000, 0x00100000);
ram_check(0x80000000, 0x80100000);
#endif
#endif
+*/
}
{ 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 }, /* u8 rfu[11] */
0x35, /* u8 checksum , this hase to set to some value that would give 0 after the sum of all bytes for this structure (including checksum) */
{
- {0x03,(0x4<<3)|0, {{0x1, 0xdef8}, {0x2, 0xdef8}, {0x3, 0xdef8}, {0x4, 0xdef8}}, 0, 0},
- {0x06, 0|0, {{0x0, 0x0000}, {0x0, 0x0000}, {0x0, 0x0000}, {0x4, 0xdef8}}, 0, 0},
- {0x01, 0|0, {{0x1, 0xdef8}, {0x2, 0xdef8}, {0, 0}, {0, 0}}, 0x0, 0},
- {0x05,(0x3<<3)|0, {{0x1, 0xdef8}, {0x2, 0xdef8}, {0x3, 0xdef8}, {0x4, 0xdef8}}, 0x1, 0},
- {0x05,(0x6<<3)|0, {{0x2, 0xdef8}, {0x3, 0xdef8}, {0x4, 0xdef8}, {0x1, 0xdef8}}, 0x2, 0},
- {0x04,(0x8<<3)|0, {{0x4, 0xdef8}, {0x1, 0xdef8}, {0x2, 0xdef8}, {0x3, 0xdef8}}, 0x3, 0},
- {0x04,(0x7<<3)|0, {{0x3, 0xdef8}, {0x4, 0xdef8}, {0x1, 0xdef8}, {0x2, 0xdef8}}, 0x4, 0},
- {0x06,(0xa<<3)|0, {{0x1, 0xdef8}, {0x2, 0xdef8}, {0x3, 0xdef8}, {0x4, 0xdef8}}, 0x5, 0},
- {0x04,(0x9<<3)|0, {{0x1, 0xdef8}, {2, 0xdef8}, {0, 0}, {0, 0}}, 0, 0},
- {0x06,(0xb<<3)|0, {{0x2, 0xdef8}, {0, 0}, {0, 0}, {0, 0}}, 0, 0},
- {0x06,(0xc<<3)|0, {{0x4, 0xdef8}, {0, 0}, {0, 0}, {0, 0}}, 0, 0},
+ {3,(4<<3)|0, {{0x1, 0xdef8}, {0x2, 0xdef8}, {0x3, 0xdef8}, {0x4, 0xdef8}}, 0, 0},
+ {0x6,0, {{0, 0}, {0, 0}, {0, 0}, {0x4, 0xdef8}}, 0, 0},
+ {0x1,0, {{0x1, 0xdef8}, {0x2, 0xdef8}, {0, 0}, {0, 0}}, 0x0, 0},
+ {0x5,(3<<3)|0, {{0x1, 0xdef8}, {0x2, 0xdef8}, {0x3, 0xdef8}, {0x4, 0xdef8}}, 0x1, 0},
+ {0x5,(6<<3)|0, {{0x2, 0xdef8}, {0x3, 0xdef8}, {0x4, 0xdef8}, {0x1, 0xdef8}}, 0x2, 0},
+ {0x4,(8<<3)|0, {{0x4, 0xdef8}, {0x1, 0xdef8}, {0x2, 0xdef8}, {0x3, 0xdef8}}, 0x3, 0},
+ {0x4,(7<<3)|0, {{0x3, 0xdef8}, {0x4, 0xdef8}, {0x1, 0xdef8}, {0x2, 0xdef8}}, 0x4, 0},
+ {0x6,(0x0a<<3)|0, {{0x1, 0xdef8}, {0x2, 0xdef8}, {0x3, 0xdef8}, {0x4, 0xdef8}}, 0x5, 0},
+ {0x4,(9<<3)|0, {{0x1, 0xdef8}, {2, 0xdef8}, {0, 0}, {0, 0}}, 0, 0},
+ {0x6,(0x0b<<3)|0, {{0x2, 0xdef8}, {0, 0}, {0, 0}, {0, 0}}, 0, 0},
+ {0x6,(0x0c<<3)|0, {{0x4, 0xdef8}, {0, 0}, {0, 0}, {0, 0}}, 0, 0},
}
};
pci_write_config8(dev, 0x43, byte);
}
#endif
+#if 0
static void onboard_scsi_fixup(void)
{
struct device *dev;
-#if 0
+#if 1
unsigned char i,j,k;
for(i=0;i<=6;i++) {
// print_mem();
// amd8111_enable_rom();
}
+#endif
#if 0
static void vga_fixup(void) {
// we do this right here because:
// case CONF_PASS_PRE_PCI:
// case CONF_PASS_POST_PCI:
case CONF_PASS_PRE_BOOT:
- if (conf->fixup_scsi)
- onboard_scsi_fixup();
+// if (conf->fixup_scsi)
+ // onboard_scsi_fixup();
// if (conf->fixup_vga)
// vga_fixup();
printk_debug("mainboard fixup pass %d done\r\n",
void *smp_write_config_table(void *v, unsigned long * processor_map)
{
- static const char sig[4] = "PCMP";
+ static const char sig[4] = "PCMP";
static const char oem[8] = "TYAN ";
static const char productid[12] = "S2885 ";
struct mp_config_table *mc;
unsigned char bus_num;
unsigned char bus_isa;
- unsigned char bus_8111_0;
- unsigned char bus_8111_1;
unsigned char bus_8131_1;
unsigned char bus_8131_2;
+ unsigned char bus_8111_1;
unsigned char bus_8151_1;
+
mc = (void *)(((char *)v) + SMP_FLOATING_TABLE_LEN);
memset(mc, 0, sizeof(*mc));
smp_write_processors(mc, processor_map);
- {
+ {
device_t dev;
/* 8111 */
dev = dev_find_slot(3, PCI_DEVFN(0x03,0));
if (dev) {
- bus_8111_0 = pci_read_config8(dev, PCI_PRIMARY_BUS);
bus_8111_1 = pci_read_config8(dev, PCI_SECONDARY_BUS);
bus_isa = pci_read_config8(dev, PCI_SUBORDINATE_BUS);
bus_isa++;
printk_debug("bus_isa=%d\n",bus_isa);
- } else {
+ }
+ else {
printk_debug("ERROR - could not find PCI 3:03.0, using defaults\n");
+
bus_8111_1 = 6;
bus_isa = 7;
}
-
/* 8131-1 */
dev = dev_find_slot(3, PCI_DEVFN(0x01,0));
if (dev) {
bus_8131_1 = pci_read_config8(dev, PCI_SECONDARY_BUS);
- } else {
+
+ }
+ else {
printk_debug("ERROR - could not find PCI 3:01.0, using defaults\n");
+
bus_8131_1 = 4;
}
/* 8131-2 */
dev = dev_find_slot(3, PCI_DEVFN(0x02,0));
if (dev) {
bus_8131_2 = pci_read_config8(dev, PCI_SECONDARY_BUS);
- } else {
+
+ }
+ else {
printk_debug("ERROR - could not find PCI 3:02.0, using defaults\n");
+
bus_8131_2 = 5;
}
- /* 8151 */
+ /* 8151 */
dev = dev_find_slot(1, PCI_DEVFN(0x02,0));
if (dev) {
bus_8151_1 = pci_read_config8(dev, PCI_SECONDARY_BUS);
- printk_debug("bus_8151_1=%d\n",bus_8151_1);
- } else {
+ printk_debug("bus_8151_1=%d\n",bus_8151_1);
+
+ }
+ else {
printk_debug("ERROR - could not find PCI 1:02.0, using defaults\n");
+
bus_8151_1 = 2;
- }
+ }
+
+
}
- /*Bus: Bus ID Type*/
- /* define bus and isa numbers */
- for (bus_num = 0; bus_num < bus_isa; bus_num++) {
+
+
+/*Bus: Bus ID Type*/
+ /* define bus and isa numbers */
+ for(bus_num = 0; bus_num < bus_isa; bus_num++) {
smp_write_bus(mc, bus_num, "PCI ");
}
smp_write_bus(mc, bus_isa, "ISA ");
- /*I/O APICs: APIC ID Version State Address*/
+/*I/O APICs: APIC ID Version State Address*/
smp_write_ioapic(mc, 2, 0x11, 0xfec00000);
{
struct pci_dev *dev;
uint32_t base;
- /* 8131-1 APIC */
dev = dev_find_slot(3, PCI_DEVFN(0x1,1));
if (dev) {
base = pci_read_config32(dev, PCI_BASE_ADDRESS_0);
base &= PCI_BASE_ADDRESS_MEM_MASK;
smp_write_ioapic(mc, 3, 0x11, base);
}
- /* 8131-2 APIC */
dev = dev_find_slot(3, PCI_DEVFN(0x2,1));
if (dev) {
base = pci_read_config32(dev, PCI_BASE_ADDRESS_0);
}
}
- /* ISA Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN# */
- smp_write_intsrc(mc, mp_ExtINT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x0, 0x2, 0x0);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x1, 0x2, 0x1);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x0, 0x2, 0x2);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x3, 0x2, 0x3);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x4, 0x2, 0x4);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x5, 0x2, 0x5);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x6, 0x2, 0x6);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x7, 0x2, 0x7);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x8, 0x2, 0x8);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0xc, 0x2, 0xc);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0xd, 0x2, 0xd);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0xe, 0x2, 0xe);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0xf, 0x2, 0xf);
-
- /* PCI Ints: Type Polarity Trigger Bus ID PCIDEVNUM|IRQ APIC ID PIN# */
- // Integrated SMBus 2.0
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_0, (0x04<<2)|3, 0x2, 0x13);
- // Integrated AMD AC97 Audio
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_0, (0x04<<2)|1, 0x2, 0x11);
-
- // Integrated AMD USB
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x00<<2)|3, 0x2, 0x13);
-
- // Onboard Serial ATA
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x0b<<2)|0, 0x2, 0x11);
- // Onboard Firewire
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x0c<<2)|0, 0x2, 0x13);
-
- // Onboard Broadcom NIC
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_1, (0x09<<2)|0, 0x3, 0x0);
-
- // AGP Display Adapter
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8151_1, 0x0, 0x2, 0x10);
-
- //Slot 5 PCI 32
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x0a<<2)|0, 0x2, 0x10);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x0a<<2)|1, 0x2, 0x11);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x0a<<2)|2, 0x2, 0x12);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x0a<<2)|3, 0x2, 0x13);
-
- //Slot 3 PCIX 100/66
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_1, (0x08<<2)|0, 0x3, 0x3);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_1, (0x08<<2)|1, 0x3, 0x0);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_1, (0x08<<2)|2, 0x3, 0x1);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_1, (0x08<<2)|3, 0x3, 0x2);
-
- //Slot 4 PCIX 100/66
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_1, (0x07<<2)|0, 0x3, 0x2);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_1, (0x07<<2)|1, 0x3, 0x3);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_1, (0x07<<2)|2, 0x3, 0x0);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_1, (0x07<<2)|3, 0x3, 0x1);
-
- //Slot 1 PCI-X 133/100/66
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_2, (0x03<<2)|0, 0x4, 0x0);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_2, (0x03<<2)|1, 0x4, 0x1);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_2, (0x03<<2)|2, 0x4, 0x2);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_2, (0x03<<2)|3, 0x4, 0x3);
-
- //Slot 2 PCI-X 133/100/66
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_2, (0x06<<2)|0, 0x4, 0x1);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_2, (0x06<<2)|1, 0x4, 0x2);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_2, (0x06<<2)|2, 0x4, 0x3);
- smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_2, (0x06<<2)|3, 0x4, 0x0);
-
- /*Local Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN# */
+/*I/O Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN#
+*/ smp_write_intsrc(mc, mp_ExtINT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x0, 0x2, 0x0);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x1, 0x2, 0x1);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x0, 0x2, 0x2);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x3, 0x2, 0x3);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x4, 0x2, 0x4);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x5, 0x2, 0x5);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x6, 0x2, 0x6);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x7, 0x2, 0x7);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x8, 0x2, 0x8);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0xc, 0x2, 0xc);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0xd, 0x2, 0xd);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0xe, 0x2, 0xe);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0xf, 0x2, 0xf);
+//??? What
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x3, (4<<2)|3, 0x2, 0x13);
+//Onboard AMD AC97 Audio ???
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x3, (4<<2)|1, 0x2, 0x11);
+// Onboard AMD USB
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0<<2)|3, 0x2, 0x13);
+
+// AGP Display Adapter
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8151_1, 0x0, 0x2, 0x10);
+
+// Onboard Serial ATA
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x0b<<2)|0, 0x2, 0x11);
+//Onboard Firewire
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x0c<<2)|0, 0x2, 0x13);
+//Onboard Broadcom NIC
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_1, (9<<2)|0, 0x3, 0x0);
+
+//Slot 5 PCI 32
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x0a<<2)|0, 0x2, 0x10);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x0a<<2)|1, 0x2, 0x11);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x0a<<2)|2, 0x2, 0x12); //
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0x0a<<2)|3, 0x2, 0x13); //
+
+//Slot 3 PCIX 100/66
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_1, (8<<2)|0, 0x3, 0x3);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_1, (8<<2)|1, 0x3, 0x0);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_1, (8<<2)|2, 0x3, 0x1);//
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_1, (8<<2)|3, 0x3, 0x2);//
+
+//Slot 4 PCIX 100/66
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_1, (7<<2)|0, 0x3, 0x2);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_1, (7<<2)|1, 0x3, 0x3);//
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_1, (7<<2)|2, 0x3, 0x0);//
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_1, (7<<2)|3, 0x3, 0x1);//
+
+//Slot 1 PCI-X 133/100/66
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_2, (3<<2)|0, 0x4, 0x0);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_2, (3<<2)|1, 0x4, 0x1);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_2, (3<<2)|2, 0x4, 0x2); //
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_2, (3<<2)|3, 0x4, 0x3); //
+
+//Slot 2 PCI-X 133/100/66
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_2, (6<<2)|0, 0x4, 0x1);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_2, (6<<2)|1, 0x4, 0x2);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_2, (6<<2)|2, 0x4, 0x3);//
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_2, (6<<2)|3, 0x4, 0x0);//
+
+/*Local Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN#*/
smp_write_intsrc(mc, mp_ExtINT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x0, MP_APIC_ALL, 0x0);
- smp_write_intsrc(mc, mp_NMI, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x0, MP_APIC_ALL, 0x1);
-
+ smp_write_intsrc(mc, mp_NMI, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x0, MP_APIC_ALL, 0x1);
/* There is no extension information... */
/* Compute the checksums */
mc->mpe_checksum = smp_compute_checksum(smp_next_mpc_entry(mc), mc->mpe_length);
mc->mpc_checksum = smp_compute_checksum(mc, mc->mpc_length);
printk_debug("Wrote the mp table end at: %p - %p\n",
- mc, smp_next_mpe_entry(mc));
+ mc, smp_next_mpe_entry(mc));
return smp_next_mpe_entry(mc);
}
default LB_CKS_LOC=123
driver mainboard.o
-driver lsi_scsi.o
+dir ../common/lsi_scsi
#driver adaptec_scsi.o
-driver si_sata.o
+#driver si_sata.o
#driver intel_nic.o
#object reset.o
if HAVE_MP_TABLE object mptable.o end
###
### Romcc output
###
-#makerule ./failover.E dep "$(MAINBOARD)/failover.c" act "$(CPP) -I$(TOP)/src $(CPPFLAGS) $(MAINBOARD)/failover.c > ./failever.E"
-#makerule ./failover.inc dep "./romcc ./failover.E" act "./romcc -O ./failover.E > failover.inc"
-#mainboardinit .failover.inc
makerule ./failover.E
depends "$(MAINBOARD)/failover.c"
makerule ./auto.inc
depends "./romcc ./auto.E"
action "./romcc -O2 -mcpu=k8 -o auto.inc --label-prefix=auto ./auto.E"
-# action "./romcc -mcpu=k8 -O ./auto.E > auto.inc"
end
mainboardinit cpu/k8/enable_mmx_sse.inc
mainboardinit ./auto.inc
}
-#define REV_B_RESET 0
static void memreset_setup(void)
{
-#if REV_B_RESET==1
+ if (is_cpu_pre_c0()) {
outb((0 << 7)|(0 << 6)|(0<<5)|(0<<4)|(1<<2)|(0<<0), SMBUS_IO_BASE + 0xc0 + 16); //REVC_MEMRST_EN=0
-#else
+ }
+ else {
outb((0 << 7)|(0 << 6)|(0<<5)|(0<<4)|(1<<2)|(1<<0), SMBUS_IO_BASE + 0xc0 + 16); //REVC_MEMRST_EN=1
-#endif
+ }
outb((0 << 7)|(0 << 6)|(0<<5)|(0<<4)|(1<<2)|(0<<0), SMBUS_IO_BASE + 0xc0 + 17);
}
static void memreset(int controllers, const struct mem_controller *ctrl)
{
+ if (is_cpu_pre_c0()) {
udelay(800);
-#if REV_B_RESET==1
outb((0<<7)|(0<<6)|(0<<5)|(0<<4)|(1<<2)|(1<<0), SMBUS_IO_BASE + 0xc0 + 17); //REVB_MEMRST_L=1
-#endif
udelay(90);
+ }
}
static unsigned int generate_row(uint8_t node, uint8_t row, uint8_t maxnodes)
default LB_CKS_LOC=123
driver mainboard.o
-driver lsi_scsi.o
+dir ../common/lsi_scsi
#driver adaptec_scsi.o
-driver si_sata.o
+#driver si_sata.o
#driver intel_nic.o
#object reset.o
if HAVE_MP_TABLE object mptable.o end
makerule ./auto.inc
depends "./romcc ./auto.E"
action "./romcc -O2 -mcpu=k8 -o auto.inc --label-prefix=auto ./auto.E"
-# action "./romcc -mcpu=k8 -O ./auto.E > auto.inc"
end
mainboardinit cpu/k8/enable_mmx_sse.inc
mainboardinit ./auto.inc
}
-#define REV_B_RESET 0
static void memreset_setup(void)
{
-#if REV_B_RESET==1
+ if (is_cpu_pre_c0()) {
outb((0 << 7)|(0 << 6)|(0<<5)|(0<<4)|(1<<2)|(0<<0), SMBUS_IO_BASE + 0xc0 + 16); //REVC_MEMRST_EN=0
-#else
+ }
+ else {
outb((0 << 7)|(0 << 6)|(0<<5)|(0<<4)|(1<<2)|(1<<0), SMBUS_IO_BASE + 0xc0 + 16); //REVC_MEMRST_EN=1
-#endif
+ }
outb((0 << 7)|(0 << 6)|(0<<5)|(0<<4)|(1<<2)|(0<<0), SMBUS_IO_BASE + 0xc0 + 17);
}
static void memreset(int controllers, const struct mem_controller *ctrl)
{
+ if (is_cpu_pre_c0()) {
udelay(800);
-#if REV_B_RESET==1
outb((0<<7)|(0<<6)|(0<<5)|(0<<4)|(1<<2)|(1<<0), SMBUS_IO_BASE + 0xc0 + 17); //REVB_MEMRST_L=1
-#endif
udelay(90);
+ }
}
static unsigned int generate_row(uint8_t node, uint8_t row, uint8_t maxnodes)
setup_s4882_resource_map();
needs_reset = setup_coherent_ht_domain();
needs_reset |= ht_setup_chain(PCI_DEV(0, 0x18, 0), 0xa0);
-#if 0
- dump_pci_device(PCI_DEV(0, 4, 0));
-#endif
if (needs_reset) {
- print_info("ht reset -");
+ print_info("ht reset -\r\n");
soft_reset();
}
projects / coreboot.git / commitdiff