/*
- * This file is part of the LinuxBIOS project.
+ * This file is part of the superiotool project.
*
* Copyright (C) 2006 coresystems GmbH <info@coresystems.de>
+ * Copyright (C) 2007 Uwe Hermann <uwe@hermann-uwe.de>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
#define DEVICE_ID_BYTE1_REG 0x20
#define DEVICE_ID_BYTE2_REG 0x21
+
#define VENDOR_ID_BYTE1_REG 0x23
#define VENDOR_ID_BYTE2_REG 0x24
#define FINTEK_VENDOR_ID 0x3419
-const static struct superio_registers reg_table[] = {
- {0x0604, "F71805", {
+static const struct superio_registers reg_table[] = {
+ {0x0106, "F71862FG", {
+ {EOT}}},
+ {0x4103, "F71872F/FG / F71806F/FG", { /* Same ID? Datasheet typo? */
{EOT}}},
- {0x4103, "F71872", {
+ {0x4105, "F71882FG/F71883FG", { /* Same ID? Datasheet typo? */
+ {EOT}}},
+ {0x0604, "F71805F/FG", {
+ /* We assume reserved bits are read as 0. */
+ {NOLDN, NULL,
+ {0x07,0x20,0x21,0x23,0x24,0x25,0x26,0x27,0x28,
+ 0x29,EOT},
+ {NANA,0x04,0x06,0x19,0x34,0x00,0x00,0x3f,0x08,
+ 0x00,EOT}},
+ {0x0, "Floppy",
+ {0x30,0x60,0x61,0x70,0x74,0xf0,0xf2,0xf4,EOT},
+ {0x01,0x03,0xf0,0x06,0x02,0x0e,0x03,0x00,EOT}},
+ {0x1, "COM1",
+ {0x30,0x60,0x61,0x70,0xf0,EOT},
+ {0x01,0x03,0xf8,0x04,0x00,EOT}},
+ {0x2, "COM2",
+ {0x30,0x60,0x61,0x70,0xf0,0xf1,EOT},
+ {0x01,0x02,0xf8,0x03,0x00,0x04,EOT}},
+ {0x3, "Parallel port",
+ {0x30,0x60,0x61,0x70,0x74,0xf0,EOT},
+ {0x01,0x03,0x78,0x07,0x03,0x42,EOT}},
+ {0x4, "Hardware monitor",
+ {0x30,0x60,0x61,0x70,EOT},
+ {0x00,0x02,0x95,0x00,EOT}},
+ {0x6, "GPIO",
+ {0x70,0xe0,0xe1,0xe2,0xe3,0xe4,0xe5,0xe6,0xe7,0xe8,
+ 0xe9,0xf0,0xf1,0xf3,0xf4,EOT},
+ {0x00,0x00,0x00,NANA,0x00,0x00,0x00,0x00,0x00,0x00,
+ 0x00,0x00,NANA,0x00,NANA,EOT}},
+ {0xa, "PME",
+ {0x30,0xf0,0xf1,EOT},
+ {0x00,0x00,0x00,EOT}},
{EOT}}},
{EOT}
};
-static void dump_readable_fintek(uint16_t port, uint16_t did)
-{
- if (!dump_readable)
- return;
-
- printf("Human-readable register dump:\n");
-
- printf("Flash write is %s.\n",
- regval(port, 0x28) & 0x80 ? "enabled" : "disabled");
- printf("Flash control is 0x%04x.\n", regval(port, 0x28));
- printf("27=%02x\n", regval(port, 0x27));
- printf("29=%02x\n", regval(port, 0x29));
- printf("2a=%02x\n", regval(port, 0x2a));
- printf("2b=%02x\n", regval(port, 0x2b));
-
- /* Select UART 1. */
- regwrite(port, 0x07, 0x01);
- printf("UART1 is %s\n",
- regval(port, 0x30) & 1 ? "enabled" : "disabled");
- printf("UART1 base=%02x%02x, irq=%02x, mode=%s\n", regval(port, 0x60),
- regval(port, 0x61), regval(port, 0x70) & 0x0f,
- regval(port, 0xf0) & 0x10 ? "RS485" : "RS232");
-
- /* Select UART 2. */
- regwrite(port, 0x07, 0x02);
- printf("UART2 is %s\n",
- regval(port, 0x30) & 1 ? "enabled" : "disabled");
- printf("UART2 base=%02x%02x, irq=%02x, mode=%s\n", regval(port, 0x60),
- regval(port, 0x61), regval(port, 0x70) & 0x0f,
- regval(port, 0xf0) & 0x10 ? "RS485" : "RS232");
-
- /* Select parallel port. */
- regwrite(port, 0x07, 0x03);
- printf("PARPORT is %s\n",
- regval(port, 0x30) & 1 ? "enabled" : "disabled");
- printf("PARPORT base=%02x%02x, irq=%02x\n", regval(port, 0x60),
- regval(port, 0x61), regval(port, 0x70) & 0x0f);
-
- /* Select HW monitor. */
- regwrite(port, 0x07, 0x04);
- printf("HW monitor is %s\n",
- regval(port, 0x30) & 1 ? "enabled" : "disabled");
- printf("HW monitor base=%02x%02x, irq=%02x\n", regval(port, 0x60),
- regval(port, 0x61), regval(port, 0x70) & 0x0f);
-
- /* Select GPIO. */
- regwrite(port, 0x07, 0x05);
- printf("GPIO is %s\n", regval(port, 0x30) & 1 ? "enabled" : "disabled");
- printf
- ("GPIO 70=%02x, e0=%02x, e1=%02x, e2=%02x, e3=%02x, e4=%02x, e5=%02x\n",
- regval(port, 0x70), regval(port, 0xe0), regval(port, 0xe1),
- regval(port, 0xe2), regval(port, 0xe3), regval(port, 0xe4),
- regval(port, 0xe5));
- printf
- ("GPIO e6=%02x, e7=%02x, e8=%02x, e9=%02x, f0=%02x, f1=%02x, f3=%02x, f4=%02x\n",
- regval(port, 0xe6), regval(port, 0xe7), regval(port, 0xe8),
- regval(port, 0xe9), regval(port, 0xf0), regval(port, 0xf1),
- regval(port, 0xf3), regval(port, 0xf4));
- printf("GPIO f5=%02x, f6=%02x, f7=%02x, f8=%02x\n", regval(port, 0xf5),
- regval(port, 0xf6), regval(port, 0xf7), regval(port, 0xf8));
-}
-
void probe_idregs_fintek(uint16_t port)
{
uint16_t vid, did;
+ probing_for("Fintek", "", port);
+
enter_conf_mode_winbond_fintek_ite_8787(port);
did = regval(port, DEVICE_ID_BYTE1_REG);
vid |= (regval(port, VENDOR_ID_BYTE2_REG) << 8);
if (vid != FINTEK_VENDOR_ID || superio_unknown(reg_table, did)) {
- no_superio_found(port);
+ if (verbose)
+ printf(NOTFOUND "vid=0x%04x, id=0x%04x\n", vid, did);
exit_conf_mode_winbond_fintek_ite_8787(port);
return;
}
- printf("Found Fintek %s (vid=0x%04x, id=0x%04x) at port=0x%x\n",
- get_superio_name(reg_table, did), vid, did, port);
+ printf("Found Fintek %s (vid=0x%04x, id=0x%04x) at 0x%x\n",
+ get_superio_name(reg_table, did), vid, did, port);
+ chip_found = 1;
dump_superio("Fintek", reg_table, port, did);
- dump_readable_fintek(port, did);
exit_conf_mode_winbond_fintek_ite_8787(port);
}
-
projects / coreboot.git / blobdiff