# You probably want to customize those
##############################################################################
TARGET=arm-none-eabi # Or: TARGET=arm-elf
-PREFIX=${HOME}/arm-none-eabi # Install location of your final toolchain
-PARALLEL= # Or: PARALLEL="-j 5" for 4 CPUs
+PREFIX=${HOME}/sat # Install location of your final toolchain
DARWIN_OPT_PATH=/opt/local # Path in which MacPorts or Fink is installed
# Set to 'sudo' if you need superuser privileges while installing
SUDO=
# Set to 1 to be quieter while running
QUIET=0
# Set to 1 to use linaro gcc instead of the FSF gcc
-USE_LINARO=0
+USE_LINARO=1
+# Set to 1 to enable building of OpenOCD
+OOCD_EN=1
# Set to 1 to build libstm32 provided by ST
LIBSTM32_EN=0
# Set to 1 to build libopenstm32 an open source library for stm32
-LIBOPENSTM32_EN=0
+LIBOPENSTM32_EN=1
# Make the gcc default to Cortex-M3
DEFAULT_TO_CORTEX_M3=0
GCCURL=http://ftp.gnu.org/gnu/gcc/${GCC}/${GCC}.tar.gz
else
# For the Linaro GCC:
- GCCVERSION=4.5-2010.08-1
+ GCCRELEASE=4.5-2010.11-0
+ GCCVERSION=4.5-2010.11-1
GCC=gcc-linaro-${GCCVERSION}
- GCCURL=http://launchpad.net/gcc-linaro/4.5/${GCCVERSION}/+download/${GCC}.tar.gz
+ GCCURL=http://launchpad.net/gcc-linaro/4.5/${GCCRELEASE}/+download/${GCC}.tar.bz2
fi
BINUTILS=binutils-2.20
NEWLIB=newlib-1.18.0
GDB=gdb-7.2
+OOCD=master
LIBCMSIS=v1.10-2
LIBSTM32=v3.0.0-1
LIBSTM32USB=v3.0.1-1
# Flags section
##############################################################################
+if which getconf > /dev/null; then
+ CPUS=$(getconf _NPROCESSORS_ONLN)
+else
+ CPUS=1
+fi
+PARALLEL=-j$((CPUS + 1))
+echo "${CPUS} cpu's detected running make with '${PARALLEL}' flag"
+
GDBFLAGS=
BINUTILFLAGS=
GCCFLAGS=
else
# To default to the Cortex-M3:
- GCCFLAGS="--with-arch=armv7-m --with-mode=thumb"
+ GCCFLAGS="--with-arch=armv7-m --with-mode=thumb --with-float=soft"
fi
# Pull in the local configuration, if any
SOURCES=${SUMMON_DIR}/sources
STAMPS=${SUMMON_DIR}/stamps
+
+##############################################################################
+# Tool section
+##############################################################################
+TAR=tar
+
+##############################################################################
+# OS and Tooldetection section
+# Detects which tools and flags to use
+##############################################################################
+
+case "$(uname)" in
+ Linux)
+ echo "Found Linux OS."
+ ;;
+ Darwin)
+ echo "Found Darwin OS."
+ GCCFLAGS="${GCCFLAGS} \
+ --with-gmp=${DARWIN_OPT_PATH} \
+ --with-mpfr=${DARWIN_OPT_PATH} \
+ --with-mpc=${DARWIN_OPT_PATH} \
+ --with-libiconv-prefix=${DARWIN_OPT_PATH}"
+ OOCD_CFLAGS="-m32 -I/opt/mine/include -I/opt/local/include"
+ OOCD_LDFLAGS="-L/opt/mine/lib -L/opt/local/lib"
+ ;;
+ CYGWIN*)
+ echo "Found CygWin that means Windows most likely."
+ ;;
+ *)
+ echo "Found unknown OS. Aborting!"
+ exit 1
+ ;;
+esac
+
##############################################################################
# Building section
# You probably don't have to touch anything after this
function unpack {
log Unpacking $*
# Use 'auto' mode decompression. Replace with a switch if tar doesn't support -a
- tar xaf${TARFLAGS} ${SOURCES}/$1.tar.*
+ ARCHIVE=$(ls ${SOURCES}/$1.tar.*)
+ case ${ARCHIVE} in
+ *.bz2)
+ echo "archive type bz2"
+ TYPE=j
+ ;;
+ *.gz)
+ echo "archive type gz"
+ TYPE=z
+ ;;
+ *)
+ echo "Unknown archive type of $1"
+ echo ${ARCHIVE}
+ exit 1
+ ;;
+ esac
+ ${TAR} xf${TYPE}${TARFLAGS} ${SOURCES}/$1.tar.*
}
# Install a build
${SUDO} make ${MAKEFLAGS} $2 $3 $4 $5 $6 $7 $8
}
-case "$(uname)" in
- Linux)
- echo "Found Linux OS."
- ;;
- Darwin)
- echo "Found Darwin OS."
- GCCFLAGS="${GCCFLAGS} \
- --with-gmp=${DARWIN_OPT_PATH} \
- --with-mpfr=${DARWIN_OPT_PATH} \
- --with-mpc=${DARWIN_OPT_PATH} \
- -with-libiconv-prefix=${DARWIN_OPT_PATH}"
- ;;
- *)
- echo "Found unknown OS. Aborting!"
- exit 1
- ;;
-esac
mkdir -p ${STAMPS} ${SOURCES}
fetch ${NEWLIB} ftp://sources.redhat.com/pub/newlib/${NEWLIB}.tar.gz
fetch ${GDB} http://ftp.gnu.org/gnu/gdb/${GDB}.tar.bz2
+if [ ${OOCD_EN} != 0 ]; then
+if [ ! -e openocd-${OOCD}.tar.bz2 ]; then
+ log "Cloning OpenOCD sources..."
+ git clone git://openocd.git.sourceforge.net/gitroot/openocd/openocd openocd-${OOCD}
+ cd openocd-${OOCD}
+ ./bootstrap
+ cd ..
+ tar cfvj openocd-${OOCD}.tar.bz2 openocd-${OOCD}
+ #git archive --format=tar --prefix=openocd-${OOCD}/ ${OOCD} | \
+ # bzip2 --stdout > ../openocd-${OOCD}.tar.bz2
+ rm -rf openocd-${OOCD}
+fi
+fi
+
if [ ${LIBSTM32_EN} != 0 ]; then
if [ ! -e libcmsis-${LIBCMSIS}.tar.bz2 ]; then
log "Cloning libcmsis sources..."
--with-gnu-ld \
--disable-nls \
--disable-werror \
- --disable-newlib-supplied-syscalls
+ --disable-newlib-supplied-syscalls \
+ --with-float=soft
log "Building ${NEWLIB}"
- make ${MAKEFLAGS}
+ make ${MAKEFLAGS} CFLAGS_FOR_TARGET="-msoft-float" CCASFLAGS="-msoft-float"
install ${NEWLIB} install
cd ..
log "Cleaning up ${NEWLIB}"
rm -rf build/* ${GDB}
fi
+if [ ${OOCD_EN} != 0 ]; then
+if [ ! -e ${STAMPS}/openocd-${OOCD}.build ]; then
+ unpack openocd-${OOCD}
+ cd build
+ log "Configuring openocd-${OOCD}"
+ CFLAGS="${CFLAGS} ${OOCD_CFLAGS}" \
+ LDFLAGS="${LDFLAGS} ${OOCD_LDFLAGS}" \
+ ../openocd-${OOCD}/configure --enable-maintainer-mode \
+ --prefix=${PREFIX} \
+ --enable-dummy \
+ --enable-parport \
+ --enable-ft2232_libftdi \
+ --enable-usb_blaster_libftdi \
+ --enable-amtjtagaccel \
+ --enable-zy1000 \
+ --enable-ep93xx \
+ --enable-at91rm9200 \
+ --enable-gw16012 \
+ --enable-presto_libftdi \
+ --enable-usbprog \
+ --enable-jlink \
+ --enable-vsllink \
+ --enable-rlink \
+ --enable-arm-jtag-ew \
+ --enable-buspirate
+ log "Building openocd-${OOCD}"
+ make ${MAKEFLAGS}
+ install openocd-${OOCD} install
+ cd ..
+ log "Cleaning up openocd-${OOCD}"
+ touch ${STAMPS}/openocd-${OOCD}.build
+ rm -rf build/* ${OOCD}
+fi
+fi
+
if [ ${LIBSTM32_EN} != 0 ]; then
-if [ ! -e .libcmsis-${LIBCMSIS}.build ]; then
+if [ ! -e ${STAMPS}/libcmsis-${LIBCMSIS}.build ]; then
unpack libcmsis-${LIBCMSIS}
cd libcmsis-${LIBCMSIS}
log "Building libcmsis-${LIBCMSIS}"
install libcmsis-${LIBCMSIS} arch_prefix=${TARGET} prefix=${PREFIX} install
cd ..
log "Cleaning up libcmsis-${LIBCMSIS}"
- touch .libcmsis-${LIBCMSIS}.build
+ touch ${STAMPS}/libcmsis-${LIBCMSIS}.build
rm -rf libcmsis-${LIBCMSIS}
fi
-if [ ! -e .libstm32-${LIBSTM32}.build ]; then
+if [ ! -e ${STAMPS}/libstm32-${LIBSTM32}.build ]; then
unpack libstm32-${LIBSTM32}
cd libstm32-${LIBSTM32}
log "Building libstm32-${LIBSTM32}"
install libstm32-${LIBSTM32} arch_prefix=${TARGET} prefix=${PREFIX} install
cd ..
log "Cleaning up libstm32-${LIBSTM32}"
- touch .libstm32-${LIBSTM32}.build
+ touch ${STAMPS}/libstm32-${LIBSTM32}.build
rm -rf libstm32-${LIBSTM32}
fi
-if [ ! -e .libstm32usb-${LIBSTM32USB}.build ]; then
+if [ ! -e ${STAMPS}/libstm32usb-${LIBSTM32USB}.build ]; then
unpack libstm32usb-${LIBSTM32USB}
cd libstm32usb-${LIBSTM32USB}
log "Building libstm32usb-${LIBSTM32USB}"
install libstm32usb-${LIBSTM32USB} arch_prefix=${TARGET} prefix=${PREFIX} install
cd ..
log "Cleaning up libstm32usb-${LIBSTM32USB}"
- touch .libstm32usb-${LIBSTM32USB}.build
+ touch ${STAMPS}/libstm32usb-${LIBSTM32USB}.build
rm -rf libstm32usb-${LIBSTM32USB}
fi
fi
if [ $LIBOPENSTM32_EN != 0 ]; then
+if [ ! -e ${STAMPS}/libopenstm32-${LIBOPENSTM32}.build ]; then
unpack libopenstm32-${LIBOPENSTM32}
cd libopenstm32-${LIBOPENSTM32}
log "Building libopenstm32-${LIBOPENSTM32}"
install libopenstm32-${LIBOPENSTM32} PREFIX=${TARGET} DESTDIR=${PREFIX} install
cd ..
log "Cleaning up libopenstm32-${LIBOPENSTM32}"
- touch .libopenstm32-${LIBOPENSTM32}.build
+ touch ${STAMPS}/libopenstm32-${LIBOPENSTM32}.build
rm -rf libopenstm32-${LIBOPENSTM32}
fi
+fi