-
-#include <arch/io.h>
-#include <device/pci.h>
-#include <device/chip.h>
#include <console/console.h>
-#include "vt8231.h"
-#include "chip.h"
-
-
-
-void usb_on(int enable)
-{
- unsigned char regval;
-
- /* Base 8231 controller */
- struct pci_dev *dev0 = pci_find_device(PCI_VENDOR_ID_VIA, \
- PCI_DEVICE_ID_VIA_8231, 0);
- /* USB controller 1 */
- struct pci_dev *dev2 = pci_find_device(PCI_VENDOR_ID_VIA, \
- PCI_DEVICE_ID_VIA_82C586_2, 0);
- /* USB controller 2 */
- struct pci_dev *dev3 = pci_find_device(PCI_VENDOR_ID_VIA, \
- PCI_DEVICE_ID_VIA_82C586_2, \
- dev2);
-
- /* enable USB1 */
- if(dev2) {
- if (enable) {
- pci_write_config_byte(dev2, 0x3c, 0x05);
- pci_write_config_byte(dev2, 0x04, 0x07);
- } else {
- pci_write_config_byte(dev2, 0x3c, 0x00);
- pci_write_config_byte(dev2, 0x04, 0x00);
- }
- }
+#include <device/device.h>
+#include <device/pci.h>
+#include <device/pci_ops.h>
+#include <device/pci_ids.h>
- if(dev0) {
- pci_read_config_byte(dev0, 0x50, ®val);
- if (enable)
- regval &= ~(0x10);
- else
- regval |= 0x10;
- pci_write_config_byte(dev0, 0x50, regval);
- }
+#include <pc80/mc146818rtc.h>
+#include <pc80/keyboard.h>
- /* enable USB2 */
- if(dev3) {
- if (enable) {
- pci_write_config_byte(dev3, 0x3c, 0x05);
- pci_write_config_byte(dev3, 0x04, 0x07);
- } else {
- pci_write_config_byte(dev3, 0x3c, 0x00);
- pci_write_config_byte(dev3, 0x04, 0x00);
- }
- }
+#include "chip.h"
- if(dev0) {
- pci_read_config_byte(dev0, 0x50, ®val);
- if (enable)
- regval &= ~(0x20);
- else
- regval |= 0x20;
- pci_write_config_byte(dev0, 0x50, regval);
- }
+/* Base 8231 controller */
+static device_t lpc_dev;
+void hard_reset(void)
+{
+ printk(BIOS_ERR, "NO HARD RESET ON VT8231! FIX ME!\n");
}
-void keyboard_on()
+static void keyboard_on(void)
{
unsigned char regval;
- /* Base 8231 controller */
- struct pci_dev *dev0 = pci_find_device(PCI_VENDOR_ID_VIA, \
- PCI_DEVICE_ID_VIA_8231, 0);
-
- /* kevinh/Ispiri - update entire function to use
- new pci_write_config_byte */
-
- if (dev0) {
- pci_read_config_byte(dev0, 0x51, ®val);
- regval |= 0x0f;
- pci_write_config_byte(dev0, 0x51, regval);
+ if (lpc_dev) {
+ regval = pci_read_config8(lpc_dev, 0x51);
+ regval |= 0x0f;
+ pci_write_config8(lpc_dev, 0x51, regval);
}
- pc_keyboard_init();
-
+ pc_keyboard_init(0);
}
-void nvram_on()
+static void com_port_on(void)
{
- /*
- * the VIA 8231 South has a very different nvram setup than the
- * piix4e ...
- * turn on ProMedia nvram.
- * TO DO: use the PciWriteByte function here.
+#if 0
+ // enable com1 and com2.
+ enables = pci_read_config8(dev, 0x6e);
+
+ /* 0x80 is enable com port b, 0x10 is to make it com2, 0x8
+ * is enable com port a as com1 kevinh/Ispiri - Old code
+ * thought 0x01 would make it com1, that was wrong enables =
+ * 0x80 | 0x10 | 0x8 ; pci_write_config8(dev, 0x6e,
+ * enables); // note: this is also a redo of some port of
+ * assembly, but we want everything up.
*/
- /*
- * kevinh/Ispiri - I don't think this is the correct address/value
- * intel_conf_writeb(0x80008841, 0xFF);
+ /* set com1 to 115 kbaud not clear how to do this yet.
+ * forget it; done in assembly.
*/
-}
-
-
-/*
- * Enable the ethernet device and turn off stepping (because it is integrated
- * inside the southbridge)
- */
-void ethernet_fixup()
-{
- struct pci_dev *dev, *edev;
- u8 byte;
-
- printk_info("Ethernet fixup\n");
-
- edev = pci_find_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8233_7, 0);
- if (edev != NULL) {
- printk_debug("Configuring VIA LAN\n");
-
- /* We don't need stepping - though the device supports it */
- pci_read_config_byte(edev, PCI_COMMAND, &byte);
- byte &= ~PCI_COMMAND_WAIT;
- pci_write_config_byte(edev, PCI_COMMAND, byte);
- } else {
- printk_debug("VIA LAN not found\n");
- }
-}
-
-
-void southbridge_fixup()
-{
- unsigned char enables;
- struct pci_dev *dev0;
- struct pci_dev *dev1;
- struct pci_dev *devpwr;
-
- // to do: use the pcibios_find function here, instead of
- // hard coding the devfn.
- // done - kevinh/Ispiri
-
- /* Base 8231 controller */
- dev0 = pci_find_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8231, 0);
- /* IDE controller */
- dev1 = pci_find_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_1, \
- 0);
- /* Power management controller */
- devpwr = pci_find_device(PCI_VENDOR_ID_VIA, \
- PCI_DEVICE_ID_VIA_8231_4, 0);
-
- // enable the internal I/O decode
- enables = pci_read_config_byte(dev0, 0x6C, &enables);
- enables |= 0x80;
- pci_write_config_byte(dev0, 0x6C, enables);
-
- // Map 4MB of FLASH into the address space
- pci_write_config_byte(dev0, 0x41, 0x7f);
-
- // Set bit 6 of 0x40, because Award does it (IO recovery time)
- // IMPORTANT FIX - EISA 0x4d0 decoding must be on so that PCI
- // interrupts can be properly marked as level triggered.
- enables = pci_read_config_byte(dev0, 0x40, &enables); enables |= 0x44;
- pci_write_config_byte(dev0, 0x40, enables);
-
- // Set 0x42 to 0xf0 to match Award bios
- enables = pci_read_config_byte(dev0, 0x42, &enables);
- enables |= 0xf0;
- pci_write_config_byte(dev0, 0x42, enables);
-
- // Set bit 3 of 0x4a, to match award (dummy pci request)
- enables = pci_read_config_byte(dev0, 0x4a, &enables);
- enables |= 0x08;
- pci_write_config_byte(dev0, 0x4a, enables);
-
- // Set bit 3 of 0x4f to match award (use INIT# as cpu reset)
- enables = pci_read_config_byte(dev0, 0x4f, &enables);
- enables |= 0x08;
- pci_write_config_byte(dev0, 0x4f, enables);
-
- // Set 0x58 to 0x03 to match Award
- pci_write_config_byte(dev0, 0x58, 0x03);
-
- // enable the ethernet/RTC
- if(dev0) {
- pci_read_config_byte(dev0, 0x51, &enables);
- enables |= 0x18;
- pci_write_config_byte(dev0, 0x51, enables);
- }
-
-
- // enable com1 and com2.
- if (conf->enable_com_ports) {
- enables = pci_read_config_byte(dev0, 0x6e, &enables);
- /* 0x80 is enable com port b, 0x10 is to make it com2, 0x8
- * is enable com port a as com1 kevinh/Ispiri - Old code
- * thought 0x01 would make it com1, that was wrong /*
- * enables = 0x80 | 0x10 | 0x8 ; pci_write_config_byte(dev0,
- * 0x6e, enables); // note: this is also a redo of some port
- * of assembly, but we want everything up.
- */
-
- /* set com1 to 115 kbaud not clear how to do this yet.
- * forget it; done in assembly.
- */
#endif
-
- // enable IDE, since Linux won't do it.
- // First do some more things to devfn (17,0)
- // note: this should already be cleared, according to the book.
- pci_read_config_byte(dev0, 0x50, &enables);
- printk_debug("IDE enable in reg. 50 is 0x%x\n", enables);
- enables &= ~8; // need manifest constant here!
- printk_debug("set IDE reg. 50 to 0x%x\n", enables);
- pci_write_config_byte(dev0, 0x50, enables);
-
- // set default interrupt values (IDE)
- pci_read_config_byte(dev0, 0x4c, &enables);
- printk_debug("IRQs in reg. 4c are 0x%x\n", enables & 0xf);
- // clear out whatever was there.
- enables &= ~0xf;
- enables |= 4;
- printk_debug("setting reg. 4c to 0x%x\n", enables);
- pci_write_config_byte(dev0, 0x4c, enables);
-
- // set up the serial port interrupts.
- // com2 to 3, com1 to 4
- pci_write_config_byte(dev0, 0x46, 0x04);
- pci_write_config_byte(dev0, 0x47, 0x03);
-
- //
- // Power management setup
- //
- // Set ACPI base address to IO 0x4000
- pci_write_config_dword(devpwr, 0x48, 0x4001);
-
- // Enable ACPI access (and setup like award)
- pci_write_config_byte(devpwr, 0x41, 0x84);
-
- // Set hardware monitor base address to IO 0x6000
- pci_write_config_dword(devpwr, 0x70, 0x6001);
-
- // Enable hardware monitor (and setup like award)
- pci_write_config_byte(devpwr, 0x74, 0x01);
-
- // set IO base address to 0x5000
- pci_write_config_dword(devpwr, 0x90, 0x5001);
-
- // Enable SMBus
- pci_write_config_byte(devpwr, 0xd2, 0x01);
-
- //
- // IDE setup
- //
- if (conf->enable_native_ide) {
- // Run the IDE controller in 'compatiblity mode - i.e. don't use PCI
- // interrupts. Using PCI ints confuses linux for some reason.
-
- pci_read_config_byte(dev1, 0x42, &enables);
- printk_debug("enables in reg 0x42 0x%x\n", enables);
- enables &= ~0xc0; // compatability mode
- pci_write_config_byte(dev1, 0x42, enables);
- pci_read_config_byte(dev1, 0x42, &enables);
- printk_debug("enables in reg 0x42 read back as 0x%x\n", enables);
- }
-
- pci_read_config_byte(dev1, 0x40, &enables);
- printk_debug("enables in reg 0x40 0x%x\n", enables);
- enables |= 3;
- pci_write_config_byte(dev1, 0x40, enables);
- pci_read_config_byte(dev1, 0x40, &enables);
- printk_debug("enables in reg 0x40 read back as 0x%x\n", enables);
-
- // Enable prefetch buffers
- pci_read_config_byte(dev1, 0x41, &enables);
- enables |= 0xf0;
- pci_write_config_byte(dev1, 0x41, enables);
-
- // Lower thresholds (cause award does it)
- pci_read_config_byte(dev1, 0x43, &enables);
- enables &= ~0x0f;
- enables |= 0x05;
- pci_write_config_byte(dev1, 0x43, enables);
-
- // PIO read prefetch counter (cause award does it)
- pci_write_config_byte(dev1, 0x44, 0x18);
-
- // Use memory read multiple
- pci_write_config_byte(dev1, 0x45, 0x1c);
-
- // address decoding.
- // we want "flexible", i.e. 1f0-1f7 etc. or native PCI
- // kevinh@ispiri.com - the standard linux drivers seem ass slow when
- // used in native mode - I've changed back to classic
- pci_read_config_byte(dev1, 0x9, &enables);
- printk_debug("enables in reg 0x9 0x%x\n", enables);
- // by the book, set the low-order nibble to 0xa.
- if (conf->enable_native_ide) {
- enables &= ~0xf;
- // cf/cg silicon needs an 'f' here.
- enables |= 0xf;
- } else {
- enables &= ~0x5;
- }
-
- pci_write_config_byte(dev1, 0x9, enables);
- pci_read_config_byte(dev1, 0x9, &enables);
- printk_debug("enables in reg 0x9 read back as 0x%x\n", enables);
-
- // standard bios sets master bit.
- pci_read_config_byte(dev1, 0x4, &enables);
- printk_debug("command in reg 0x4 0x%x\n", enables);
- enables |= 7;
-
- // No need for stepping - kevinh@ispiri.com
- enables &= ~0x80;
-
- pci_write_config_byte(dev1, 0x4, enables);
- pci_read_config_byte(dev1, 0x4, &enables);
- printk_debug("command in reg 0x4 reads back as 0x%x\n", enables);
-
- if (! conf->enable_native_ide) {
- // Use compatability mode - per award bios
- pci_write_config_dword(dev1, 0x10, 0x0);
- pci_write_config_dword(dev1, 0x14, 0x0);
- pci_write_config_dword(dev1, 0x18, 0x0);
- pci_write_config_dword(dev1, 0x1c, 0x0);
-
- // Force interrupts to use compat mode - just like Award bios
- pci_write_config_byte(dev1, 0x3d, 00);
- pci_write_config_byte(dev1, 0x3c, 0xff);
- }
-
-
- ethernet_fixup();
-
- // Start the rtc
- rtc_init(0);
}
-static void
-southbridge_init(struct chip *chip, enum chip_pass pass)
+/* FixME: to be removed ? */
+static void vt8231_enable(struct device *dev)
{
-
- struct southbridge_via_vt8231_config *conf =
- (struct southbridge_via_vt8231_config *)chip->chip_info;
-
- switch (pass) {
- case CONF_PASS_POST_PCI:
- vt8231_init(conf);
- break;
-
- default:
- /* nothing yet */
- break;
+ struct southbridge_via_vt8231_config *conf = dev->chip_info;
+
+ if (!lpc_dev) {
+ /* the first time called, enable devices not on PCI bus
+ * FIXME: is that device struct there yet? */
+ lpc_dev = dev_find_device(PCI_VENDOR_ID_VIA,
+ PCI_DEVICE_ID_VIA_8231, 0);
+ if (conf->enable_keyboard)
+ keyboard_on();
+ if (conf->enable_com_ports)
+ com_port_on();
}
}
-struct chip_control southbridge_via_vt8231_control = {
- enable: southbridge_init,
- name: "VIA vt8231"
+struct chip_operations southbridge_via_vt8231_ops = {
+ CHIP_NAME("VIA VT8231 Southbridge")
+ .enable_dev = vt8231_enable,
};
projects / coreboot.git / blobdiff