/*
- * This file is part of the LinuxBIOS project.
+ * This file is part of the coreboot project.
*
* Copyright (C) 2004 Tyan Computer
* Written by Yinghai Lu <yhlu@tyan.com> for Tyan Computer.
static void set_apc(struct device *dev)
{
- uint32_t tmp;
uint16_t addr;
- uint32_t idx;
uint16_t i;
uint8_t bTmp;
#define LoopNum 200
static unsigned long ReadEEprom( struct device *dev, uint32_t base, uint32_t Reg)
{
- uint16_t data;
+ uint32_t data;
uint32_t i;
uint32_t ulValue;
if(i==LoopNum) data=0x10000;
else{
ulValue=readl(base+0x3c);
- data = (uint16_t)((ulValue & 0xffff0000) >> 16);
+ data = ((ulValue & 0xffff0000) >> 16);
}
return data;
static int phy_read(uint32_t base, unsigned phy_addr, unsigned phy_reg)
{
uint32_t ulValue;
- unsigned loop = 0x100;
uint32_t Read_Cmd;
uint16_t usData;
- uint16_t tmp;
Read_Cmd = ((phy_reg << 11) |
// SmiMgtInterface Reg is the SMI management interface register(offset 44h) of MAC
writel( Read_Cmd,base+0x44);
- //outl( Read_Cmd,tmp+0x44);
// Polling SMI_REQ bit to be deasserted indicated read command completed
do
{
// Wait 20 usec before checking status
- //StallAndWait(20);
mdelay(20);
ulValue = readl(base+0x44);
- //ulValue = inl(tmp+0x44);
} while((ulValue & SMI_REQUEST) != 0);
//printk_debug("base %x cmd %lx ret val %lx\n", tmp,Read_Cmd,ulValue);
usData=(ulValue>>16);
static int phy_detect(uint32_t base,uint16_t *PhyAddr) //BOOL PHY_Detect()
{
int bFoundPhy = FALSE;
- uint32_t Read_Cmd;
uint16_t usData;
int PhyAddress = 0;
static void nic_init(struct device *dev)
{
- uint32_t dword, old;
- uint32_t mac_h, mac_l;
- int eeprom_valid = 0;
int val;
uint16_t PhyAddr;
- struct southbridge_sis_sis966_config *conf;
- static uint32_t nic_index = 0;
uint32_t base;
struct resource *res;
- uint32_t reg;
print_debug("NIC_INIT:---------->\n");
print_debug("NIC_INIT:<----------\n");
return;
-#define RegStationMgtInf 0x44
-#define PHY_RGMII 0x10000000
-
- writel(PHY_RGMII, base + RegStationMgtInf);
- conf = dev->chip_info;
-
- if(conf->mac_eeprom_smbus != 0) {
-// read MAC address from EEPROM at first
-
- struct device *dev_eeprom;
- dev_eeprom = dev_find_slot_on_smbus(conf->mac_eeprom_smbus, conf->mac_eeprom_addr);
-
- if(dev_eeprom) {
- // if that is valid we will use that
- unsigned char dat[6];
- int status;
- int i;
- for(i=0;i<6;i++) {
- status = smbus_read_byte(dev_eeprom, i);
- if(status < 0) break;
- dat[i] = status & 0xff;
- }
- if(status >= 0) {
- mac_l = 0;
- for(i=3;i>=0;i--) {
- mac_l <<= 8;
- mac_l += dat[i];
- }
- if(mac_l != 0xffffffff) {
- mac_l += nic_index;
- mac_h = 0;
- for(i=5;i>=4;i--) {
- mac_h <<= 8;
- mac_h += dat[i];
- }
- eeprom_valid = 1;
- }
- }
- }
- }
-
-// if that is invalid we will read that from romstrap
- if(!eeprom_valid) {
- unsigned long mac_pos;
- mac_pos = 0xffffffd0; // refer to romstrap.inc and romstrap.lds
- mac_l = readl(mac_pos) + nic_index; // overflow?
- mac_h = readl(mac_pos + 4);
-
- }
-
-// set that into NIC MMIO
-#define NvRegMacAddrA 0xA8
-#define NvRegMacAddrB 0xAC
- writel(mac_l, base + NvRegMacAddrA);
- writel(mac_h, base + NvRegMacAddrB);
-
- nic_index++;
-
-#if CONFIG_PCI_ROM_RUN == 1
- pci_dev_init(dev);// it will init option rom
-#endif
}
// .enable = sis966_enable,
.ops_pci = &lops_pci,
};
+
static const struct pci_driver nic_driver __pci_driver = {
.ops = &nic_ops,
.vendor = PCI_VENDOR_ID_SIS,
- .device = PCI_DEVICE_ID_SIS_SIS966_NIC1,
+ .device = PCI_DEVICE_ID_SIS_SIS966_NIC,
};