#ifndef _SB700_EARLY_SETUP_C_
#define _SB700_EARLY_SETUP_C_
+#include <stdint.h>
+#include <arch/cpu.h>
+#include <arch/io.h>
+#include <arch/romcc_io.h>
+#include <console/console.h>
+#include <cpu/x86/msr.h>
+
#include <reset.h>
#include <arch/cpu.h>
#include <cbmem.h>
#include "sb700.h"
-#include "smbus.c"
+#include "smbus.h"
-#define SMBUS_IO_BASE 0x6000 /* Is it a temporary SMBus I/O base address? */
- /*SIZE 0x40 */
static void pmio_write(u8 reg, u8 value)
{
static void sb700_acpi_init(void)
{
+ u16 word;
pmio_write(0x20, ACPI_PM_EVT_BLK & 0xFF);
pmio_write(0x21, ACPI_PM_EVT_BLK >> 8);
pmio_write(0x22, ACPI_PM1_CNT_BLK & 0xFF);
* index 20-2B to decode ACPI I/O address.
* AcpiSmiEn & SmiCmdEn*/
pmio_write(0x10, 1<<1 | 1<<3| 1<<5); /* RTC_En_En, TMR_En_En, GBL_EN_EN */
+ word = inl(ACPI_PM1_CNT_BLK);
+ word |= 1;
+ outl(word, ACPI_PM1_CNT_BLK); /* set SCI_EN */
}
/* RPR 2.28: Get SB ASIC Revision. */
* Console output through any port besides 0x3f8 is unsupported.
* If you use FWH ROMs, you have to setup IDSEL.
***************************************/
-static void sb700_lpc_init(void)
+void sb7xx_51xx_lpc_init(void)
{
u8 reg8;
u32 reg32;
reg32 |= 1 << 20;
pci_write_config32(dev, 0x64, reg32);
+#if CONFIG_SOUTHBRIDGE_AMD_SUBTYPE_SP5100
+ post_code(0x66);
+ dev = pci_locate_device(PCI_ID(0x1002, 0x439d), 0); /* LPC Controller */
+ reg8 = pci_read_config8(dev, 0xBB);
+ reg8 |= 1 << 2 | 1 << 3 | 1 << 6 | 1 << 7;
+ reg8 &= ~(1 << 1);
+ pci_write_config8(dev, 0xBB, reg8);
+#endif
+
dev = pci_locate_device(PCI_ID(0x1002, 0x439d), 0); /* LPC Controller */
/* Decode port 0x3f8-0x3ff (Serial 0) */
// XXX Serial port decode on LPC is hardcoded to 0x3f8
reg8 = pci_read_config8(dev, 0x44);
reg8 |= 1 << 6;
+#if CONFIG_SOUTHBRIDGE_AMD_SUBTYPE_SP5100
+#if CONFIG_TTYS0_BASE == 0x2f8
+ reg8 |= 1 << 7;
+#endif
+#endif
pci_write_config8(dev, 0x44, reg8);
/* Decode port 0x60 & 0x64 (PS/2 keyboard) and port 0x62 & 0x66 (ACPI)*/
pci_write_config8(dev, 0x48, reg8);
}
+void sb7xx_51xx_enable_wideio(u8 wio_index, u16 base)
+{
+ /* TODO: Now assume wio_index=0 */
+ device_t dev;
+ u8 reg8;
+
+ dev = pci_locate_device(PCI_ID(0x1002, 0x439d), 0); /* LPC Controller */
+ pci_write_config32(dev, 0x64, base);
+ reg8 = pci_read_config8(dev, 0x48);
+ reg8 |= 1 << 2;
+ pci_write_config8(dev, 0x48, reg8);
+}
+
+void sb7xx_51xx_disable_wideio(u8 wio_index)
+{
+ /* TODO: Now assume wio_index=0 */
+ device_t dev;
+ u8 reg8;
+
+ dev = pci_locate_device(PCI_ID(0x1002, 0x439d), 0); /* LPC Controller */
+ pci_write_config32(dev, 0x64, 0);
+ reg8 = pci_read_config8(dev, 0x48);
+ reg8 &= ~(1 << 2);
+ pci_write_config8(dev, 0x48, reg8);
+}
+
/* what is its usage? */
-static u32 get_sbdn(u32 bus)
+u32 __attribute__ ((weak)) get_sbdn(u32 bus)
{
device_t dev;
/*
* RPR 2.4 C-state and VID/FID change for the K8 platform.
*/
-static void enable_fid_change_on_sb(u32 sbbusn, u32 sbdn)
+void __attribute__((weak)) enable_fid_change_on_sb(u32 sbbusn, u32 sbdn)
{
u8 byte;
byte = pmio_read(0x9a);
pmio_write(0x67, 0x6);
}
-void hard_reset(void)
-{
- set_bios_reset();
-
- /* full reset */
- outb(0x0a, 0x0cf9);
- outb(0x0e, 0x0cf9);
-}
-
-void soft_reset(void)
-{
- set_bios_reset();
- /* link reset */
- outb(0x06, 0x0cf9);
-}
-
-void sb700_pci_port80(void)
+void sb7xx_51xx_pci_port80(void)
{
u8 byte;
device_t dev;
pci_write_config8(dev, 0x4A, byte);
}
-void sb700_lpc_port80(void)
+void sb7xx_51xx_lpc_port80(void)
{
u8 byte;
device_t dev;
{
device_t dev;
u8 byte;
+#if CONFIG_SOUTHBRIDGE_AMD_SUBTYPE_SP5100
+ u32 dword;
+#endif
printk(BIOS_INFO, "sb700_devices_por_init()\n");
/* SMBus Device, BDF:0-20-0 */
/* DMA enable */
pci_write_config8(dev, 0x40, 0x04);
- /* LPC Sync Timeout */
+ /* IO Port Decode Enable */
+ pci_write_config8(dev, 0x44, 0xFF);
+ pci_write_config8(dev, 0x45, 0xFF);
+ pci_write_config8(dev, 0x46, 0xC3);
+ pci_write_config8(dev, 0x47, 0xFF);
+
+ // TODO: This has already been done(?)
+ /* IO/Mem Port Decode Enable, I don't know why CIM disable some ports.
+ * Disable LPC TimeOut counter, enable SuperIO Configuration Port (2e/2f),
+ * Alternate Super I/O Configuration Port (4e/4f), Wide Generic IO Port (64/65). */
+ byte = pci_read_config8(dev, 0x48);
+ byte |= (1 << 1) | (1 << 0); /* enable Super IO config port 2e-2h, 4e-4f */
+ byte |= 1 << 6; /* enable for RTC I/O range */
+ pci_write_config8(dev, 0x48, byte);
pci_write_config8(dev, 0x49, 0xFF);
+ /* Enable 0x480-0x4bf, 0x4700-0x470B */
+ byte = pci_read_config8(dev, 0x4A);
+ byte |= ((1 << 1) + (1 << 6)); /*0x42, save the configuraion for port 0x80. */
+ pci_write_config8(dev, 0x4A, byte);
/* Enable Tpm12_en and Tpm_legacy. I don't know what is its usage and copied from CIM. */
pci_write_config8(dev, 0x7C, 0x05);
/* Enable PCIB_DUAL_EN_UP will fix potential problem with PCI cards. */
pci_write_config8(dev, 0x50, 0x01);
+#if CONFIG_SOUTHBRIDGE_AMD_SUBTYPE_SP5100
+ /* SP5100 default SATA mode is RAID5 MODE */
+ dev = pci_locate_device(PCI_ID(0x1002, 0x4393), 0);
+ /* Set SATA Operation Mode, Set to IDE mode */
+ byte = pci_read_config8(dev, 0x40);
+ byte |= (1 << 0);
+ pci_write_config8(dev, 0x40, byte);
+
+ dword = 0x01018f00;
+ pci_write_config32(dev, 0x8, dword);
+
+ /* set SATA Device ID writable */
+ dword = pci_read_config32(dev, 0x40);
+ dword &= ~(1 << 24);
+ pci_write_config32(dev, 0x40, dword);
+
+ /* set Device ID accommodate with IDE emulation mode configuration*/
+ pci_write_config32(dev, 0x0, 0x43901002);
+
+ /* rpr v2.13 4.17 Reset CPU on Sync Flood */
+ abcfg_reg(0x10050, 1 << 2, 1 << 2);
+#endif
+
/* SATA Device, BDF:0-17-0, Non-Raid-5 SATA controller */
printk(BIOS_INFO, "sb700_devices_por_init(): SATA Device, BDF:0-18-0\n");
dev = pci_locate_device(PCI_ID(0x1002, 0x4390), 0);
/*
* It should be called during early POST after memory detection and BIOS shadowing but before PCI bus enumeration.
*/
-static void sb700_before_pci_init(void)
+void sb7xx_51xx_before_pci_init(void)
{
sb700_pci_cfg();
}
/*
* This function should be called after enable_sb700_smbus().
*/
-static void sb700_early_setup(void)
+void sb7xx_51xx_early_setup(void)
{
printk(BIOS_INFO, "sb700_early_setup()\n");
sb700_por_init();
sb700_acpi_init();
}
-static int smbus_read_byte(u32 device, u32 address)
-{
- return do_smbus_read_byte(SMBUS_IO_BASE, device, address);
-}
-
int s3_save_nvram_early(u32 dword, int size, int nvram_pos)
{
int i;
}
#if CONFIG_HAVE_ACPI_RESUME == 1
-static int acpi_is_wakeup_early(void)
+int acpi_is_wakeup_early(void)
{
u16 tmp;
tmp = inw(ACPI_PM1_CNT_BLK);