* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*/
-/* Note: Some of the VGA control registers are located on the memory controller.
- Registers are set both in raminit.c and northbridge.c */
+/*
+ * Note: Some of the VGA control registers are located on the memory
+ * controller. Registers are set both in raminit.c and northbridge.c.
+ */
#include <console/console.h>
#include <arch/io.h>
#include "chip.h"
#include "northbridge.h"
#include "cn700.h"
+#include "vgachip.h"
void write_protect_vgabios(void)
{
-//Don't bother for now
+ /* Don't bother for now. */
}
static void vga_init(device_t dev)
{
u8 reg8;
- print_debug("Copying BOCHS Bios to 0xf000\n");
- /* Copy BOCHS BIOS from 4G-ROM_SIZE-64k (in flash) to 0xf0000 (in RAM)
- * This is for compatibility with the VGA ROM's BIOS callbacks */
- memcpy(0xf0000, (0xffffffff - ROM_SIZE - 0xffff), 0x10000);
+ print_debug("Copying BOCHS BIOS to 0xf000\n");
+ /*
+ * Copy BOCHS BIOS from 4G-CONFIG_ROM_SIZE-64k (in flash) to 0xf0000 (in RAM)
+ * This is for compatibility with the VGA ROM's BIOS callbacks.
+ */
+ memcpy(0xf0000, (0xffffffff - CONFIG_ROM_SIZE - 0xffff), 0x10000);
+
+ printk(BIOS_DEBUG, "Initializing VGA\n");
- printk_debug("Initializing VGA\n");
-
- /* Set memory rate to 200MHz */
+ /* Set memory rate to 200 MHz. */
outb(0x3d, CRTM_INDEX);
reg8 = inb(CRTM_DATA);
reg8 &= 0x0f;
reg8 |= (0x1 << 4);
outb(0x3d, CRTM_INDEX);
outb(reg8, CRTM_DATA);
-
- /* Set framebuffer size */
+
+ /* Set framebuffer size. */
reg8 = (CONFIG_VIDEO_MB / 4);
outb(0x39, SR_INDEX);
outb(reg8, SR_DATA);
-
-
+
pci_write_config8(dev, 0x04, 0x07);
pci_write_config8(dev, 0x0d, 0x20);
- pci_write_config32(dev,0x10, 0xf4000008);
- pci_write_config32(dev,0x14, 0xfb000000);
-
-
- printk_debug("INSTALL REAL-MODE IDT\n");
+ pci_write_config32(dev, 0x10, 0xf4000008);
+ pci_write_config32(dev, 0x14, 0xfb000000);
+
+ printk(BIOS_DEBUG, "INSTALL REAL-MODE IDT\n");
setup_realmode_idt();
- printk_debug("DO THE VGA BIOS\n");
+ printk(BIOS_DEBUG, "DO THE VGA BIOS\n");
do_vgabios();
- /* VGA seems to work without this, but crash & burn with it */
- //printk_debug("Enable VGA console\n");
- //vga_enable_console();
+ /* VGA seems to work without this, but crash & burn with it. */
+ // printk(BIOS_DEBUG, "Enable VGA console\n");
+ // vga_enable_console();
/* It's not clear if these need to be programmed before or after
- * the VGA bios runs. Try both, clean up later */
- /* Set memory rate to 200MHz */
+ * the VGA BIOS runs. Try both, clean up later. */
+ /* Set memory rate to 200 MHz (again). */
outb(0x3d, CRTM_INDEX);
reg8 = inb(CRTM_DATA);
reg8 &= 0x0f;
reg8 |= (0x1 << 4);
outb(0x3d, CRTM_INDEX);
outb(reg8, CRTM_DATA);
-
- /* Set framebuffer size (again) */
+
+ /* Set framebuffer size (again). */
reg8 = (CONFIG_VIDEO_MB / 4);
outb(0x39, SR_INDEX);
outb(reg8, SR_DATA);
- /* Clear the BOCHs Bios out of memory, so it doesn't confuse linux */
+ /* Clear the BOCHS BIOS out of memory, so it doesn't confuse Linux. */
memset(0xf0000, 0, 0x10000);
}
-static void vga_read_resources(device_t dev)
-{
- dev->rom_address = 0xfff80000;
- dev->on_mainboard=1;
- pci_dev_read_resources(dev);
-}
-
-
static const struct device_operations vga_operations = {
- .read_resources = vga_read_resources,
+ .read_resources = pci_dev_read_resources,
.set_resources = pci_dev_set_resources,
.enable_resources = pci_dev_enable_resources,
.init = vga_init,
};
static const struct pci_driver vga_driver __pci_driver = {
- .ops = &vga_operations,
+ .ops = &vga_operations,
.vendor = PCI_VENDOR_ID_VIA,
.device = PCI_DEVICE_ID_VIA_CN700_VGA,
};