-uses HAVE_MP_TABLE
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HARD_RESET_BUS
-uses HARD_RESET_DEVICE
-uses HARD_RESET_FUNCTION
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_CBFS
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_MAX_CPUS
+uses CONFIG_MAX_PHYSICAL_CPUS
+uses CONFIG_LOGICAL_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
-uses CONFIG_ROM_STREAM
-uses CONFIG_ROM_STREAM_START
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
-uses LINUXBIOS_EXTRA_VERSION
-uses _RAMBASE
-uses CC
-uses HOSTCC
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
+uses CONFIG_ROM_PAYLOAD
+uses CONFIG_ROM_PAYLOAD_START
+uses CONFIG_COMPRESSED_PAYLOAD_LZMA
+uses CONFIG_PRECOMPRESSED_PAYLOAD
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses COREBOOT_EXTRA_VERSION
+uses CONFIG_RAMBASE
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_SERIAL8250
-uses HAVE_INIT_TIMER
+uses CONFIG_HAVE_INIT_TIMER
uses CONFIG_GDB_STUB
+uses CONFIG_GDB_STUB
+uses CONFIG_CROSS_COMPILE
+uses CC
+uses HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_CONSOLE_VGA
+uses CONFIG_PCI_ROM_RUN
+uses CONFIG_HW_MEM_HOLE_SIZEK
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
+uses CONFIG_USE_INIT
+uses CONFIG_USE_PRINTK_IN_CAR
###
### Build options
###
##
-## ROM_SIZE is the size of boot ROM that this board will use.
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
##
-default ROM_SIZE=524288
+default CONFIG_ROM_SIZE=524288
##
-## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
+## CONFIG_FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
##
-default FALLBACK_SIZE=131072
+#default CONFIG_FALLBACK_SIZE=131072
+#256K
+default CONFIG_FALLBACK_SIZE=0x40000
##
## Build code for the fallback boot
##
-default HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FALLBACK_BOOT=1
##
-## Build code to reset the motherboard from linuxBIOS
-##
-default HAVE_HARD_RESET=1
-
+## Build code to reset the motherboard from coreboot
##
-## Funky hard reset implementation
-##
-default HARD_RESET_BUS=1
-default HARD_RESET_DEVICE=4
-default HARD_RESET_FUNCTION=0
+default CONFIG_HAVE_HARD_RESET=1
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=15
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=15
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
-default HAVE_MP_TABLE=1
+default CONFIG_HAVE_MP_TABLE=1
##
## Build code to export a CMOS option table
##
-default HAVE_OPTION_TABLE=1
+default CONFIG_HAVE_OPTION_TABLE=1
##
-## Move the default LinuxBIOS cmos range off of AMD RTC registers
+## Move the default coreboot cmos range off of AMD RTC registers
##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
+default CONFIG_LB_CKS_RANGE_START=49
+default CONFIG_LB_CKS_RANGE_END=122
+default CONFIG_LB_CKS_LOC=123
##
## Build code for SMP support
## Only worry about 2 micro processors
##
default CONFIG_SMP=1
-default CONFIG_MAX_CPUS=2
+default CONFIG_MAX_CPUS=4
+default CONFIG_MAX_PHYSICAL_CPUS=2
+default CONFIG_LOGICAL_CPUS=1
+
+#1G memory hole
+default CONFIG_HW_MEM_HOLE_SIZEK=0x100000
+
+#VGA Console
+default CONFIG_CONSOLE_VGA=1
+default CONFIG_PCI_ROM_RUN=1
+
+
+##
+## enable CACHE_AS_RAM specifics
+##
+default CONFIG_USE_DCACHE_RAM=1
+default CONFIG_DCACHE_RAM_BASE=0xcf000
+default CONFIG_DCACHE_RAM_SIZE=0x1000
+default CONFIG_USE_INIT=0
##
## Build code to setup a generic IOAPIC
##
## Clean up the motherboard id strings
##
-default MAINBOARD_PART_NUMBER="Tyan"
-default MAINBOARD_VENDOR="s2882"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x10f1
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2882
+default CONFIG_MAINBOARD_PART_NUMBER="S2882"
+default CONFIG_MAINBOARD_VENDOR="Tyan"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x10f1
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2882
###
-### LinuxBIOS layout values
+### coreboot layout values
###
-## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy.
-default ROM_IMAGE_SIZE = 65536
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 65536
##
## Use a small 8K stack
##
-default STACK_SIZE=0x2000
+default CONFIG_STACK_SIZE=0x2000
##
## Use a small 16K heap
##
-default HEAP_SIZE=0x4000
+default CONFIG_HEAP_SIZE=0x4000
##
## Only use the option table in a normal image
##
-default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
+default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
##
-## LinuxBIOS C code runs at this location in RAM
+## Coreboot C code runs at this location in RAM
##
-default _RAMBASE=0x00004000
+default CONFIG_RAMBASE=0x00004000
##
## Load the payload from the ROM
##
-default CONFIG_ROM_STREAM = 1
+default CONFIG_ROM_PAYLOAD = 1
###
### Defaults of options that you may want to override in the target config file
##
## The default compiler
##
-default CC="gcc"
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
default HOSTCC="gcc"
##
##
default CONFIG_GDB_STUB=0
+default CONFIG_USE_PRINTK_IN_CAR=1
+
##
## The Serial Console
##
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
# Select the serial console base port
-default TTYS0_BASE=0x3f8
+default CONFIG_TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
+default CONFIG_TTYS0_LCS=0x3
##
-### Select the linuxBIOS loglevel
+### Select the coreboot loglevel
##
## EMERG 1 system is unusable
## ALERT 2 action must be taken immediately
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
-## DEBUG 8 debug-level messages
+## CONFIG_DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
-default DEFAULT_CONSOLE_LOGLEVEL=7
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
## At a maximum only compile in this level of debugging
-default MAXIMUM_CONSOLE_LOGLEVEL=8
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
##
## Select power on after power fail setting
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
### End Options.lb
+#
+# CBFS
+#
+#
+default CONFIG_CBFS=0
end
projects / coreboot.git / blobdiff