## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-uses HAVE_MP_TABLE
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses USE_FAILOVER_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_FAILOVER_BOOT
-uses HAVE_HARD_RESET
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
+uses CONFIG_GENERATE_MP_TABLE
+uses CONFIG_GENERATE_PIRQ_TABLE
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_USE_FAILOVER_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_FAILOVER_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
uses CONFIG_MAX_CPUS
uses CONFIG_MAX_PHYSICAL_CPUS
uses CONFIG_LOGICAL_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses FAILOVER_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_FAILOVER_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
-uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_NRV2B
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses COREBOOT_EXTRA_VERSION
-uses _RAMBASE
-uses TTYS0_BAUD
-uses TTYS0_BASE
-uses TTYS0_LCS
-uses DEFAULT_CONSOLE_LOGLEVEL
-uses MAXIMUM_CONSOLE_LOGLEVEL
-uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_RAMBASE
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_SERIAL8250
-uses HAVE_INIT_TIMER # ?
-uses CROSS_COMPILE
+uses CONFIG_HAVE_INIT_TIMER # ?
+uses CONFIG_CROSS_COMPILE
uses CC
uses HOSTCC
-uses OBJCOPY
-uses CONFIG_CHIP_NAME
+uses CONFIG_OBJCOPY
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
uses CONFIG_USBDEBUG_DIRECT
-uses HW_MEM_HOLE_SIZEK
-uses HW_MEM_HOLE_SIZE_AUTO_INC
-uses K8_HT_FREQ_1G_SUPPORT
-uses HT_CHAIN_UNITID_BASE
-uses HT_CHAIN_END_UNITID_BASE
-uses SB_HT_CHAIN_ON_BUS0
-uses SB_HT_CHAIN_UNITID_OFFSET_ONLY
-uses USE_DCACHE_RAM
-uses DCACHE_RAM_BASE
-uses DCACHE_RAM_SIZE
-uses DCACHE_RAM_GLOBAL_VAR_SIZE
+uses CONFIG_HW_MEM_HOLE_SIZEK
+uses CONFIG_HW_MEM_HOLE_SIZE_AUTO_INC
+uses CONFIG_K8_HT_FREQ_1G_SUPPORT
+uses CONFIG_HT_CHAIN_UNITID_BASE
+uses CONFIG_HT_CHAIN_END_UNITID_BASE
+uses CONFIG_SB_HT_CHAIN_ON_BUS0
+uses CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
+uses CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE
uses CONFIG_USE_INIT
-uses SERIAL_CPU_INIT
-uses ENABLE_APIC_EXT_ID
-uses APIC_ID_OFFSET
-uses LIFT_BSP_APIC_ID
+uses CONFIG_SERIAL_CPU_INIT
+uses CONFIG_ENABLE_APIC_EXT_ID
+uses CONFIG_APIC_ID_OFFSET
+uses CONFIG_LIFT_BSP_APIC_ID
uses CONFIG_PCI_64BIT_PREF_MEM
-uses CONFIG_LB_MEM_TOPK
+uses CONFIG_RAMTOP
uses CONFIG_AP_CODE_IN_CAR
-uses MEM_TRAIN_SEQ
-uses WAIT_BEFORE_CPUS_INIT
+uses CONFIG_MEM_TRAIN_SEQ
+uses CONFIG_WAIT_BEFORE_CPUS_INIT
uses CONFIG_USE_PRINTK_IN_CAR
+uses CONFIG_ID_SECTION_OFFSET
-default ROM_SIZE = 512 * 1024
-default FALLBACK_SIZE = (256 * 1024) - (4 * 1024)
-default FAILOVER_SIZE = 4 * 1024
-default CONFIG_LB_MEM_TOPK = 2048 # 1MB more for pgtbl.
-default HAVE_FALLBACK_BOOT = 1
-default HAVE_FAILOVER_BOOT = 1
-default HAVE_HARD_RESET = 1
-default HAVE_PIRQ_TABLE = 1
-default IRQ_SLOT_COUNT = 11 # TODO: Check if correct.
-default HAVE_MP_TABLE = 1 # TODO: Check if correct.
-default HAVE_OPTION_TABLE = 1
+default CONFIG_ROM_SIZE = 512 * 1024
+default CONFIG_FALLBACK_SIZE = CONFIG_ROM_IMAGE_SIZE
+default CONFIG_FAILOVER_SIZE = 4 * 1024
+default CONFIG_RAMTOP = 2048*1024 # 1MB more for pgtbl.
+default CONFIG_HAVE_FALLBACK_BOOT = 1
+default CONFIG_HAVE_FAILOVER_BOOT = 1
+default CONFIG_HAVE_HARD_RESET = 1
+default CONFIG_GENERATE_PIRQ_TABLE = 1
+default CONFIG_IRQ_SLOT_COUNT = 11 # TODO: Check if correct.
+default CONFIG_GENERATE_MP_TABLE = 1 # TODO: Check if correct.
+default CONFIG_HAVE_OPTION_TABLE = 1
default CONFIG_SMP = 1
default CONFIG_MAX_CPUS = 2
default CONFIG_MAX_PHYSICAL_CPUS = 1
default CONFIG_LOGICAL_CPUS = 1
-# default SERIAL_CPU_INIT = 0
-default ENABLE_APIC_EXT_ID = 0
-default APIC_ID_OFFSET = 0x10
-default LIFT_BSP_APIC_ID = 1
-default CONFIG_CHIP_NAME = 1
+# default CONFIG_SERIAL_CPU_INIT = 0
+default CONFIG_ENABLE_APIC_EXT_ID = 0
+default CONFIG_APIC_ID_OFFSET = 0x10
+default CONFIG_LIFT_BSP_APIC_ID = 1
# Move the default coreboot CMOS range off of AMD RTC registers.
-default LB_CKS_RANGE_START = 49
-default LB_CKS_RANGE_END = 122
-default LB_CKS_LOC = 123
+default CONFIG_LB_CKS_RANGE_START = 49
+default CONFIG_LB_CKS_RANGE_END = 122
+default CONFIG_LB_CKS_LOC = 123
# Memory hole size. 0 means disable, others will enable the hole. In that
# case, if it is smaller than mmio_basek, it will use mmio_basek instead.
-# default HW_MEM_HOLE_SIZEK = 0x200000 # 2GB
-default HW_MEM_HOLE_SIZEK = 0x100000 # 1GB
-# default HW_MEM_HOLE_SIZEK = 0x80000 # 512MB
+# default CONFIG_HW_MEM_HOLE_SIZEK = 0x200000 # 2GB
+default CONFIG_HW_MEM_HOLE_SIZEK = 0x100000 # 1GB
+# default CONFIG_HW_MEM_HOLE_SIZEK = 0x80000 # 512MB
# Make auto increase hole size to avoid hole_startk equal to basek so as
# to make some kernel happy.
-# default HW_MEM_HOLE_SIZE_AUTO_INC = 1
+# default CONFIG_HW_MEM_HOLE_SIZE_AUTO_INC = 1
# Opteron K8 1G HT support.
-default K8_HT_FREQ_1G_SUPPORT = 1
+default CONFIG_K8_HT_FREQ_1G_SUPPORT = 1
# HT Unit ID offset, default is 1, the typical one, 0 means only one HT device.
-default HT_CHAIN_UNITID_BASE = 0
+default CONFIG_HT_CHAIN_UNITID_BASE = 0
# Real SB Unit ID, default is 0x20, mean don't touch it at last.
-# default HT_CHAIN_END_UNITID_BASE = 0x6
+# default CONFIG_HT_CHAIN_END_UNITID_BASE = 0x6
# Make the SB HT chain on bus 0, default is not (0).
-default SB_HT_CHAIN_ON_BUS0 = 2
+default CONFIG_SB_HT_CHAIN_ON_BUS0 = 2
# Only offset for SB chain? Default is yes (1).
-default SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0
+default CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0
# Allow capable device use that above 4GB.
# default CONFIG_PCI_64BIT_PREF_MEM = 1
default CONFIG_CONSOLE_VGA = 1 # Needed for VGA.
default CONFIG_PCI_ROM_RUN = 1 # Needed for VGA.
default CONFIG_USBDEBUG_DIRECT = 0
-default USE_DCACHE_RAM = 1
-default DCACHE_RAM_BASE = 0xc8000
-default DCACHE_RAM_SIZE = 0x08000
-default DCACHE_RAM_GLOBAL_VAR_SIZE = 0x01000
+default CONFIG_USE_DCACHE_RAM = 1
+default CONFIG_DCACHE_RAM_BASE = 0xc8000
+default CONFIG_DCACHE_RAM_SIZE = 0x08000
+default CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE = 0x01000
default CONFIG_USE_INIT = 0
default CONFIG_AP_CODE_IN_CAR = 0
-default MEM_TRAIN_SEQ = 2
-default WAIT_BEFORE_CPUS_INIT = 0
+default CONFIG_MEM_TRAIN_SEQ = 2
+default CONFIG_WAIT_BEFORE_CPUS_INIT = 0
default CONFIG_IOAPIC = 1
-default MAINBOARD_PART_NUMBER = "K9N Neo (MS-7260)"
-default MAINBOARD_VENDOR = "MSI"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID = 0x1462
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID = 0x7260
-default ROM_IMAGE_SIZE = 65536
-default STACK_SIZE = 0x2000
-default HEAP_SIZE = 0x8000
-default USE_OPTION_TABLE = (!USE_FALLBACK_IMAGE) && (!USE_FAILOVER_IMAGE)
-default _RAMBASE = 0x00100000
+default CONFIG_MAINBOARD_PART_NUMBER = "K9N Neo (MS-7260)"
+default CONFIG_MAINBOARD_VENDOR = "MSI"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID = 0x1462
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID = 0x7260
+default CONFIG_ROM_IMAGE_SIZE = 65536 - CONFIG_FAILOVER_SIZE
+default CONFIG_STACK_SIZE = 0x2000
+default CONFIG_HEAP_SIZE = 0x8000
+default CONFIG_USE_OPTION_TABLE = (!CONFIG_USE_FALLBACK_IMAGE) && (!CONFIG_USE_FAILOVER_IMAGE)
+default CONFIG_RAMBASE = 0x00100000
default CONFIG_ROM_PAYLOAD = 1
-default CC = "$(CROSS_COMPILE)gcc -m32"
+default CC = "$(CONFIG_CROSS_COMPILE)gcc -m32"
default HOSTCC = "gcc"
default CONFIG_USE_PRINTK_IN_CAR = 1
default CONFIG_CONSOLE_SERIAL8250 = 1
-default TTYS0_BAUD = 115200
-default TTYS0_BASE = 0x3f8
-default TTYS0_LCS = 0x3
-default DEFAULT_CONSOLE_LOGLEVEL = 9
-default MAXIMUM_CONSOLE_LOGLEVEL = 9
-default MAINBOARD_POWER_ON_AFTER_POWER_FAIL = "MAINBOARD_POWER_ON"
+default CONFIG_TTYS0_BAUD = 115200
+default CONFIG_TTYS0_BASE = 0x3f8
+default CONFIG_TTYS0_LCS = 0x3
+default CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9
+default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL = "MAINBOARD_POWER_ON"
+default CONFIG_ID_SECTION_OFFSET=0x80
end
projects / coreboot.git / blobdiff