#include "northbridge/amd/amdfam10/raminit.h"
#include "northbridge/amd/amdfam10/amdfam10.h"
#include <lib.h>
-
#include "cpu/x86/lapic/boot_cpu.c"
#include "northbridge/amd/amdfam10/reset_test.c"
-
#include <console/loglevel.h>
#include "cpu/x86/bist.h"
-
-static int smbus_read_byte(u32 device, u32 address);
-
-#include "superio/ite/it8712f/it8712f_early_serial.c"
-#include <usbdebug.h>
-
+#include "superio/ite/it8712f/early_serial.c"
#include "cpu/x86/mtrr/earlymtrr.c"
#include <cpu/amd/mtrr.h>
#include "northbridge/amd/amdfam10/setup_resource_map.c"
-
-#include "southbridge/amd/rs780/rs780_early_setup.c"
-#include "southbridge/amd/sb700/sb700_early_setup.c"
+#include "southbridge/amd/rs780/early_setup.c"
+#include "southbridge/amd/sb700/sb700.h"
+#include "southbridge/amd/sb700/smbus.h"
#include "northbridge/amd/amdfam10/debug.c"
-static void activate_spd_rom(const struct mem_controller *ctrl)
-{
-}
+static void activate_spd_rom(const struct mem_controller *ctrl) { }
static int spd_read_byte(u32 device, u32 address)
{
- int result;
- result = smbus_read_byte(device, address);
- return result;
+ return do_smbus_read_byte(SMBUS_IO_BASE, device, address);
}
#include "northbridge/amd/amdfam10/amdfam10.h"
-
#include "northbridge/amd/amdfam10/raminit_sysinfo_in_ram.c"
-#include "northbridge/amd/amdfam10/amdfam10_pci.c"
-
+#include "northbridge/amd/amdfam10/pci.c"
#include "resourcemap.c"
#include "cpu/amd/quadcore/quadcore.c"
-
#include "cpu/amd/car/post_cache_as_ram.c"
#include "cpu/amd/microcode/microcode.c"
+
+#if CONFIG_UPDATE_CPU_MICROCODE
#include "cpu/amd/model_10xxx/update_microcode.c"
-#include "cpu/amd/model_10xxx/init_cpus.c"
+#endif
+#include "cpu/amd/model_10xxx/init_cpus.c"
#include "northbridge/amd/amdfam10/early_ht.c"
-#include "southbridge/amd/sb700/sb700_early_setup.c"
#include <spd.h>
-//#include "spd_addr.h"
-
-#define RC00 0
-#define RC01 1
-
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
-
struct sys_info *sysinfo = (struct sys_info *)(CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE);
static const u8 spd_addr[] = {RC00, DIMM0, DIMM2, 0, 0, DIMM1, DIMM3, 0, 0, };
- u32 bsp_apicid = 0;
- u32 val;
+ u32 bsp_apicid = 0, val;
msr_t msr;
if (!cpu_init_detectedx && boot_cpu()) {
/* mov bsp to bus 0xff when > 8 nodes */
set_bsp_node_CHtExtNodeCfgEn();
enumerate_ht_chain();
-
- sb700_pci_port80();
+ sb7xx_51xx_pci_port80();
}
post_code(0x30);
post_code(0x32);
enable_rs780_dev8();
- sb700_lpc_init();
+ sb7xx_51xx_lpc_init();
it8712f_enable_serial(0, CONFIG_TTYS0_BASE);
- it8712f_kill_watchdog(); /* disable watchdog, so it does not reset while still booting */
- uart_init();
-
-#if CONFIG_USBDEBUG
- sb700_enable_usbdebug(CONFIG_USBDEBUG_DEFAULT_PORT);
- early_usbdebug_init();
-#endif
+ it8712f_kill_watchdog();
console_init();
- printk(BIOS_DEBUG, "\n");
// dump_mem(CONFIG_DCACHE_RAM_BASE+CONFIG_DCACHE_RAM_SIZE-0x200, CONFIG_DCACHE_RAM_BASE+CONFIG_DCACHE_RAM_SIZE);
/* Setup sysinfo defaults */
set_sysinfo_in_ram(0);
+#if CONFIG_UPDATE_CPU_MICROCODE
update_microcode(val);
+#endif
post_code(0x33);
cpuSetAMDMSR();
/* run _early_setup before soft-reset. */
rs780_early_setup();
- sb700_early_setup();
+ sb7xx_51xx_early_setup();
#if CONFIG_SET_FIDVID
msr = rdmsr(0xc0010071);
dump_pci_device_range(PCI_DEV(0, 0x18, 3), 0, 0x200);
*/
-// ram_check(0x00200000, 0x00200000 + (640 * 1024));
-// ram_check(0x40200000, 0x40200000 + (640 * 1024));
-
-
// die("After MCT init before CAR disabled.");
rs780_before_pci_init();
- sb700_before_pci_init();
+ sb7xx_51xx_before_pci_init();
post_code(0x42);
- printk(BIOS_DEBUG, "\n*** Yes, the copy/decompress is taking a while, FIXME!\n");
post_cache_as_ram(); // BSP switch stack to ram, copy then execute LB.
post_code(0x43); // Should never see this post code.
}
+
+/**
+ * BOOL AMD_CB_ManualBUIDSwapList(u8 Node, u8 Link, u8 **List)
+ * Description:
+ * This routine is called every time a non-coherent chain is processed.
+ * BUID assignment may be controlled explicitly on a non-coherent chain. Provide a
+ * swap list. The first part of the list controls the BUID assignment and the
+ * second part of the list provides the device to device linking. Device orientation
+ * can be detected automatically, or explicitly. See documentation for more details.
+ *
+ * Automatic non-coherent init assigns BUIDs starting at 1 and incrementing sequentially
+ * based on each device's unit count.
+ *
+ * Parameters:
+ * @param[in] u8 node = The node on which this chain is located
+ * @param[in] u8 link = The link on the host for this chain
+ * @param[out] u8** list = supply a pointer to a list
+ * @param[out] BOOL result = true to use a manual list
+ * false to initialize the link automatically
+ */
+BOOL AMD_CB_ManualBUIDSwapList (u8 node, u8 link, const u8 **List)
+{
+ static const u8 swaplist[] = { 0xFF, CONFIG_HT_CHAIN_UNITID_BASE, CONFIG_HT_CHAIN_END_UNITID_BASE, 0xFF };
+ /* If the BUID was adjusted in early_ht we need to do the manual override */
+ if ((CONFIG_HT_CHAIN_UNITID_BASE != 0) && (CONFIG_HT_CHAIN_END_UNITID_BASE != 0)) {
+ printk(BIOS_DEBUG, "AMD_CB_ManualBUIDSwapList()\n");
+ if ((node == 0) && (link == 0)) { /* BSP SB link */
+ *List = swaplist;
+ return 1;
+ }
+ }
+
+ return 0;
+}