* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*/
-
-#define ASSEMBLY 1
-#define __PRE_RAM__
-
#define SYSTEM_TYPE 0 /* SERVER */
//#define SYSTEM_TYPE 1 /* DESKTOP */
//#define SYSTEM_TYPE 2 /* MOBILE */
-
#define RAMINIT_SYSINFO 1
#define CACHE_AS_RAM_ADDRESS_DEBUG 1
#define FAM10_ALLOCATE_IO_RANGE 0
//used by init_cpus and fidvid
-#define FAM10_SET_FIDVID 1
-#define FAM10_SET_FIDVID_CORE_RANGE 0
+#define SET_FIDVID 1
+#define SET_FIDVID_CORE_RANGE 0
#include <stdint.h>
#include <string.h>
#include <cpu/x86/lapic.h>
#include "option_table.h"
#include "pc80/mc146818rtc_early.c"
-
-/* FIXME: Use console.c post_code function */
-static void post_code(u8 value) {
- outb(value, 0x80);
-}
-
-#if (CONFIG_USE_FAILOVER_IMAGE == 0)
-#include "arch/i386/lib/console.c"
+#include "console/console.c"
#include "pc80/serial.c"
#include "lib/ramtest.c"
#include <cpu/amd/model_10xxx_rev.h>
#include "southbridge/amd/amd8111/amd8111_early_smbus.c"
#include "northbridge/amd/amdfam10/raminit.h"
#include "northbridge/amd/amdfam10/amdfam10.h"
-#endif
#include "cpu/x86/lapic/boot_cpu.c"
#include "northbridge/amd/amdfam10/reset_test.c"
#if 0
void die(const char *msg);
int do_printk(int msg_level, const char *fmt, ...) __attribute__((format(printf, 2, 3)));
-#define printk_emerg(fmt, arg...) do_printk(BIOS_EMERG ,fmt, ##arg)
+#define printk(BIOS_EMERG, fmt, arg...) do_printk(BIOS_EMERG ,fmt, ##arg)
#endif
#include "cpu/x86/bist.h"
-
-#if (CONFIG_USE_FAILOVER_IMAGE == 0)
-
#include "northbridge/amd/amdfam10/debug.c"
#include "superio/winbond/w83627hf/w83627hf_early_serial.c"
#include "cpu/amd/mtrr/amd_earlymtrr.c"
outb((0 << 7)|(0 << 6)|(0<<5)|(0<<4)|(1<<2)|(0<<0), SMBUS_IO_BASE + 0xc0 + 17);
}
-
static void memreset(int controllers, const struct mem_controller *ctrl)
{
}
-
static void activate_spd_rom(const struct mem_controller *ctrl)
{
#define SMBUS_HUB 0x18
int ret,i;
u8 device = ctrl->spd_switch_addr;
- printk_debug("switch i2c to : %02x for node %02x \n", device, ctrl->node_id);
+ printk(BIOS_DEBUG, "switch i2c to : %02x for node %02x \n", device, ctrl->node_id);
/* the very first write always get COL_STS=1 and ABRT_STS=1, so try another time*/
i=2;
smbus_write_byte(SMBUS_HUB, 0x03, 0);
}
-
static int spd_read_byte(u32 device, u32 address)
{
int result;
#include "cpu/amd/model_10xxx/init_cpus.c"
#include "cpu/amd/model_10xxx/fidvid.c"
-#endif /* (CONFIG_USE_FAILOVER_IMAGE == 0) */
-
-
#include "southbridge/amd/amd8111/amd8111_enable_rom.c"
#include "northbridge/amd/amdfam10/early_ht.c"
-#if (CONFIG_USE_FAILOVER_IMAGE==0)
#include "spd_addr.h"
#include "cpu/amd/microcode/microcode.c"
#include "cpu/amd/model_10xxx/update_microcode.c"
u32 val;
msr_t msr;
- if (!((cpu_init_detectedx) || (!boot_cpu()))) {
+ if (!cpu_init_detectedx && boot_cpu()) {
/* Nothing special needs to be done to find bus 0 */
/* Allow the HT devices to be found */
/* mov bsp to bus 0xff when > 8 nodes */
w83627hf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
- printk_debug("\n");
+ printk(BIOS_DEBUG, "\n");
// dump_mem(CONFIG_DCACHE_RAM_BASE+CONFIG_DCACHE_RAM_SIZE-0x200, CONFIG_DCACHE_RAM_BASE+CONFIG_DCACHE_RAM_SIZE);
// Load MPB
val = cpuid_eax(1);
- printk_debug("BSP Family_Model: %08x \n", val);
- printk_debug("*sysinfo range: ["); print_debug_hex32((u32)sysinfo); print_debug(","); print_debug_hex32((u32)sysinfo+sizeof(struct sys_info)); print_debug("]\n");
- printk_debug("bsp_apicid = %02x \n", bsp_apicid);
- printk_debug("cpu_init_detectedx = %08x \n", cpu_init_detectedx);
+ printk(BIOS_DEBUG, "BSP Family_Model: %08x \n", val);
+ printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo,sysinfo+1);
+ printk(BIOS_DEBUG, "bsp_apicid = %02x \n", bsp_apicid);
+ printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx \n", cpu_init_detectedx);
/* Setup sysinfo defaults */
set_sysinfo_in_ram(0);
#if CONFIG_LOGICAL_CPUS==1
/* Core0 on each node is configured. Now setup any additional cores. */
- printk_debug("start_other_cores()\n");
+ printk(BIOS_DEBUG, "start_other_cores()\n");
start_other_cores();
post_code(0x37);
wait_all_other_cores_started(bsp_apicid);
post_code(0x38);
- #if FAM10_SET_FIDVID == 1
+ #if SET_FIDVID == 1
msr = rdmsr(0xc0010071);
- printk_debug("\nBegin FIDVID MSR 0xc0010071 0x%08x 0x%08x \n", msr.hi, msr.lo);
+ printk(BIOS_DEBUG, "\nBegin FIDVID MSR 0xc0010071 0x%08x 0x%08x \n", msr.hi, msr.lo);
/* FIXME: The sb fid change may survive the warm reset and only
need to be done once.*/
/* show final fid and vid */
msr=rdmsr(0xc0010071);
- printk_debug("End FIDVIDMSR 0xc0010071 0x%08x 0x%08x \n", msr.hi, msr.lo);
+ printk(BIOS_DEBUG, "End FIDVIDMSR 0xc0010071 0x%08x 0x%08x \n", msr.hi, msr.lo);
#endif
-
/* Reset for HT, FIDVID, PLL and errata changes to take affect. */
if (!warm_reset_detect(0)) {
print_info("...WARM RESET...\n\n\n");
post_code(0x3B);
-
/* FIXME: Move this to chipset init.
enable cf9 for hard reset */
print_debug("enable_cf9_x()\n");
post_code(0x3C);
/* It's the time to set ctrl in sysinfo now; */
- printk_debug("fill_mem_ctrl()\n");
+ printk(BIOS_DEBUG, "fill_mem_ctrl()\n");
fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);
post_code(0x3D);
-
- printk_debug("enable_smbus()\n");
+ printk(BIOS_DEBUG, "enable_smbus()\n");
enable_smbus();
post_code(0x3E);
-
memreset_setup();
post_code(0x40);
// die("Die Before MCT init.");
- printk_debug("raminit_amdmct()\n");
+ printk(BIOS_DEBUG, "raminit_amdmct()\n");
raminit_amdmct(sysinfo);
post_code(0x41);
-
/*
dump_pci_device_range(PCI_DEV(0, 0x18, 0), 0, 0x200);
dump_pci_device_range(PCI_DEV(0, 0x18, 1), 0, 0x200);
// ram_check(0x00200000, 0x00200000 + (640 * 1024));
// ram_check(0x40200000, 0x40200000 + (640 * 1024));
-
// die("After MCT init before CAR disabled.");
post_code(0x42);
- printk_debug("\n*** Yes, the copy/decompress is taking a while, FIXME!\n");
+ printk(BIOS_DEBUG, "\n*** Yes, the copy/decompress is taking a while, FIXME!\n");
post_cache_as_ram(); // BSP switch stack to ram, copy then execute LB.
post_code(0x43); // Should never see this post code.
-
}
-
-#endif /* CONFIG_USE_FAILOVER_IMAGE==0 */
projects / coreboot.git / blobdiff