{
u8 byte;
- printk_info("%s.\n", __func__);
+ printk(BIOS_INFO, "%s.\n", __func__);
/* set index register 0C50h to 13h (miscellaneous control) */
outb(0x13, 0xC50); /* CMIndex */
static void get_ide_dma66()
{
u8 byte;
- /*u32 sm_dev, ide_dev; */
- device_t sm_dev, ide_dev;
- struct bus pbus;
+ struct device *sm_dev;
+ struct device *ide_dev;
+ printk(BIOS_INFO, "%s.\n", __func__);
sm_dev = dev_find_slot(0, PCI_DEVFN(0x14, 0));
- byte =
- pci_cf8_conf1.read8(&pbus, sm_dev->bus->secondary,
- sm_dev->path.pci.devfn, 0xA9);
+ byte = pci_read_config8(sm_dev, 0xA9);
byte |= (1 << 5); /* Set Gpio9 as input */
- pci_cf8_conf1.write8(&pbus, sm_dev->bus->secondary,
- sm_dev->path.pci.devfn, 0xA9, byte);
+ pci_write_config8(sm_dev, 0xA9, byte);
ide_dev = dev_find_slot(0, PCI_DEVFN(0x14, 1));
- byte =
- pci_cf8_conf1.read8(&pbus, ide_dev->bus->secondary,
- ide_dev->path.pci.devfn, 0x56);
+ byte = pci_read_config8(ide_dev, 0x56);
byte &= ~(7 << 0);
- if ((1 << 5) & pci_cf8_conf1.
- read8(&pbus, sm_dev->bus->secondary, sm_dev->path.pci.devfn,
- 0xAA))
+ if ((1 << 5) & pci_read_config8(sm_dev, 0xAA))
byte |= 2 << 0; /* mode 2 */
else
byte |= 5 << 0; /* mode 5 */
- pci_cf8_conf1.write8(&pbus, ide_dev->bus->secondary,
- ide_dev->path.pci.devfn, 0x56, byte);
+ pci_write_config8(ide_dev, 0x56, byte);
}
/*
u8 byte;
u16 word;
device_t sm_dev;
- struct bus pbus;
/* set ADT 7461 */
ADT7461_write_byte(0x0B, 0x50); /* Local Temperature Hight limit */
byte = ADT7461_read_byte(0x02); /* read status register to clear it */
ARA_read_byte(0x05); /* A hardware alert can only be cleared by the master sending an ARA as a read command */
- printk_info("Init adt7461 end , status 0x02 %02x\n", byte);
+ printk(BIOS_INFO, "Init adt7461 end , status 0x02 %02x\n", byte);
/* sb600 settings for thermal config */
/* set SB600 GPIO 64 to GPIO with pull-up */
/* set GPIO 64 to input */
sm_dev = dev_find_slot(0, PCI_DEVFN(0x14, 0));
- word =
- pci_cf8_conf1.read16(&pbus, sm_dev->bus->secondary,
- sm_dev->path.pci.devfn, 0x56);
+ word = pci_read_config16(sm_dev, 0x56);
word |= 1 << 7;
- pci_cf8_conf1.write16(&pbus, sm_dev->bus->secondary,
- sm_dev->path.pci.devfn, 0x56, word);
+ pci_write_config16(sm_dev, 0x56, word);
/* set GPIO 64 internal pull-up */
byte = pm2_ioread(0xf0);
struct mainboard_config *mainboard =
(struct mainboard_config *)dev->chip_info;
- printk_info("Mainboard DBM690T Enable. dev=0x%p\n", dev);
+ printk(BIOS_INFO, "Mainboard DBM690T Enable. dev=0x%p\n", dev);
#if (CONFIG_GFXUMA == 1)
msr_t msr, msr2;
/* TOP_MEM: the top of DRAM below 4G */
msr = rdmsr(TOP_MEM);
- printk_info("%s, TOP MEM: msr.lo = 0x%08x, msr.hi = 0x%08x\n",
+ printk(BIOS_INFO, "%s, TOP MEM: msr.lo = 0x%08x, msr.hi = 0x%08x\n",
__func__, msr.lo, msr.hi);
/* TOP_MEM2: the top of DRAM above 4G */
msr2 = rdmsr(TOP_MEM2);
- printk_info("%s, TOP MEM2: msr2.lo = 0x%08x, msr2.hi = 0x%08x\n",
+ printk(BIOS_INFO, "%s, TOP MEM2: msr2.lo = 0x%08x, msr2.hi = 0x%08x\n",
__func__, msr2.lo, msr2.hi);
switch (msr.lo) {
}
uma_memory_base = msr.lo - uma_memory_size; /* TOP_MEM1 */
- printk_info("%s: uma size 0x%08llx, memory start 0x%08llx\n",
+ printk(BIOS_INFO, "%s: uma size 0x%08llx, memory start 0x%08llx\n",
__func__, uma_memory_size, uma_memory_base);
/* TODO: TOP_MEM2 */
* in some circumstances we want the memory mentioned as reserved.
*/
#if (CONFIG_GFXUMA == 1)
- printk_info("uma_memory_base=0x%llx, uma_memory_size=0x%llx \n",
+ printk(BIOS_INFO, "uma_memory_base=0x%llx, uma_memory_size=0x%llx \n",
uma_memory_base, uma_memory_size);
lb_add_memory_range(mem, LB_MEM_RESERVED,
uma_memory_base, uma_memory_size);