+/*
+ * This file is part of the coreboot project.
+ *
+ * It was originally based on the Linux kernel (drivers/pci/pci.c).
+ *
+ * Modifications are:
+ * Copyright (C) 2003-2004 Linux Networx
+ * (Written by Eric Biederman <ebiederman@lnxi.com> for Linux Networx)
+ * Copyright (C) 2003-2006 Ronald G. Minnich <rminnich@gmail.com>
+ * Copyright (C) 2004-2005 Li-Ta Lo <ollie@lanl.gov>
+ * Copyright (C) 2005-2006 Tyan
+ * (Written by Yinghai Lu <yhlu@tyan.com> for Tyan)
+ * Copyright (C) 2005-2007 Stefan Reinauer <stepan@openbios.org>
+ */
+
/*
* PCI Bus Services, see include/linux/pci.h for further explanation.
*
* David Mosberger-Tang
*
* Copyright 1997 -- 1999 Martin Mares <mj@atrey.karlin.mff.cuni.cz>
- *
- * Copyright 2003 -- Eric Biederman <ebiederman@lnxi.com>
*/
#include <console/console.h>
#include <device/device.h>
#include <device/pci.h>
#include <device/pci_ids.h>
-#include <device/chip.h>
#include <part/hard_reset.h>
#include <part/fallback_boot.h>
+#include <delay.h>
+#if CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT == 1
+#include <device/hypertransport.h>
+#endif
+#if CONFIG_PCIX_PLUGIN_SUPPORT == 1
+#include <device/pcix.h>
+#endif
+#if CONFIG_PCIEXP_PLUGIN_SUPPORT == 1
+#include <device/pciexp.h>
+#endif
+#if CONFGI_AGP_PLUGIN_SUPPORT == 1
+#include <device/agp.h>
+#endif
+#if CONFIG_CARDBUS_PLUGIN_SUPPORT == 1
+#include <device/cardbus.h>
+#endif
+
+uint8_t pci_moving_config8(struct device *dev, unsigned reg)
+{
+ uint8_t value, ones, zeroes;
+ value = pci_read_config8(dev, reg);
+
+ pci_write_config8(dev, reg, 0xff);
+ ones = pci_read_config8(dev, reg);
+
+ pci_write_config8(dev, reg, 0x00);
+ zeroes = pci_read_config8(dev, reg);
+
+ pci_write_config8(dev, reg, value);
+
+ return ones ^ zeroes;
+}
+
+uint16_t pci_moving_config16(struct device *dev, unsigned reg)
+{
+ uint16_t value, ones, zeroes;
+ value = pci_read_config16(dev, reg);
+
+ pci_write_config16(dev, reg, 0xffff);
+ ones = pci_read_config16(dev, reg);
+
+ pci_write_config16(dev, reg, 0x0000);
+ zeroes = pci_read_config16(dev, reg);
+
+ pci_write_config16(dev, reg, value);
+
+ return ones ^ zeroes;
+}
+
+uint32_t pci_moving_config32(struct device *dev, unsigned reg)
+{
+ uint32_t value, ones, zeroes;
+ value = pci_read_config32(dev, reg);
+
+ pci_write_config32(dev, reg, 0xffffffff);
+ ones = pci_read_config32(dev, reg);
+
+ pci_write_config32(dev, reg, 0x00000000);
+ zeroes = pci_read_config32(dev, reg);
+
+ pci_write_config32(dev, reg, value);
+
+ return ones ^ zeroes;
+}
+
+unsigned pci_find_next_capability(device_t dev, unsigned cap, unsigned last)
+{
+ unsigned pos;
+ unsigned status;
+ unsigned reps = 48;
+ pos = 0;
+ status = pci_read_config16(dev, PCI_STATUS);
+ if (!(status & PCI_STATUS_CAP_LIST)) {
+ return 0;
+ }
+ switch(dev->hdr_type & 0x7f) {
+ case PCI_HEADER_TYPE_NORMAL:
+ case PCI_HEADER_TYPE_BRIDGE:
+ pos = PCI_CAPABILITY_LIST;
+ break;
+ case PCI_HEADER_TYPE_CARDBUS:
+ pos = PCI_CB_CAPABILITY_LIST;
+ break;
+ default:
+ return 0;
+ }
+ pos = pci_read_config8(dev, pos);
+ while(reps-- && (pos >= 0x40)) { /* loop through the linked list */
+ int this_cap;
+ pos &= ~3;
+ this_cap = pci_read_config8(dev, pos + PCI_CAP_LIST_ID);
+ printk_spew("Capability: 0x%02x @ 0x%02x\n", cap, pos);
+ if (this_cap == 0xff) {
+ break;
+ }
+ if (!last && (this_cap == cap)) {
+ return pos;
+ }
+ if (last == pos) {
+ last = 0;
+ }
+ pos = pci_read_config8(dev, pos + PCI_CAP_LIST_NEXT);
+ }
+ return 0;
+}
+
+unsigned pci_find_capability(device_t dev, unsigned cap)
+{
+ return pci_find_next_capability(dev, cap, 0);
+
+}
/** Given a device and register, read the size of the BAR for that register.
* @param dev Pointer to the device structure
* @param resource Pointer to the resource structure
* @param index Address of the pci configuration register
*/
-static struct resource *pci_get_resource(struct device *dev, unsigned long index)
+struct resource *pci_get_resource(struct device *dev, unsigned long index)
{
struct resource *resource;
- uint32_t addr, size, base;
- unsigned long type;
+ unsigned long value, attr;
+ resource_t moving, limit;
/* Initialize the resources to nothing */
- resource = get_resource(dev, index);
+ resource = new_resource(dev, index);
- addr = pci_read_config32(dev, index);
+ /* Get the initial value */
+ value = pci_read_config32(dev, index);
- /* FIXME: more consideration for 64-bit PCI devices,
- * we currently detect their size but otherwise
- * treat them as 32-bit resources
- */
- /* get the size */
- pci_write_config32(dev, index, ~0);
- size = pci_read_config32(dev, index);
+ /* See which bits move */
+ moving = pci_moving_config32(dev, index);
- /* get the minimum value the bar can be set to */
- pci_write_config32(dev, index, 0);
- base = pci_read_config32(dev, index);
-
- /* restore addr */
- pci_write_config32(dev, index, addr);
+ /* Initialize attr to the bits that do not move */
+ attr = value & ~moving;
+ /* If it is a 64bit resource look at the high half as well */
+ if (((attr & PCI_BASE_ADDRESS_SPACE_IO) == 0) &&
+ ((attr & PCI_BASE_ADDRESS_MEM_LIMIT_MASK) == PCI_BASE_ADDRESS_MEM_LIMIT_64))
+ {
+ /* Find the high bits that move */
+ moving |= ((resource_t)pci_moving_config32(dev, index + 4)) << 32;
+ }
+ /* Find the resource constraints.
+ *
+ * Start by finding the bits that move. From there:
+ * - Size is the least significant bit of the bits that move.
+ * - Limit is all of the bits that move plus all of the lower bits.
+ * See PCI Spec 6.2.5.1 ...
+ */
+ limit = 0;
+ if (moving) {
+ resource->size = 1;
+ resource->align = resource->gran = 0;
+ while(!(moving & resource->size)) {
+ resource->size <<= 1;
+ resource->align += 1;
+ resource->gran += 1;
+ }
+ resource->limit = limit = moving | (resource->size - 1);
+ }
/*
* some broken hardware has read-only registers that do not
- * really size correctly. You can tell this if addr == size
+ * really size correctly.
* Example: the acer m7229 has BARs 1-4 normally read-only.
* so BAR1 at offset 0x10 reads 0x1f1. If you size that register
* by writing 0xffffffff to it, it will read back as 0x1f1 -- a
* violation of the spec.
- * We catch this case and ignore it by settting size and type to 0.
- * This incidentally catches the common case where registers
- * read back as 0 for both address and size.
+ * We catch this case and ignore it by observing which bits move,
+ * This also catches the common case unimplemented registers
+ * that always read back as 0.
*/
- if ((addr == size) && (addr == base)) {
- if (size != 0) {
+ if (moving == 0) {
+ if (value != 0) {
printk_debug(
"%s register %02x(%08x), read-only ignoring it\n",
- dev_path(dev),
- index, addr);
+ dev_path(dev), index, value);
}
resource->flags = 0;
}
- /* Now compute the actual size, See PCI Spec 6.2.5.1 ... */
- else if (size & PCI_BASE_ADDRESS_SPACE_IO) {
- type = size & (~PCI_BASE_ADDRESS_IO_MASK);
- /* BUG! Top 16 bits can be zero (or not)
- * So set them to 0xffff so they go away ...
- */
- resource->size = (~((size | 0xffff0000) & PCI_BASE_ADDRESS_IO_MASK)) +1;
- resource->align = log2(resource->size);
- resource->gran = resource->align;
+ else if (attr & PCI_BASE_ADDRESS_SPACE_IO) {
+ /* An I/O mapped base address */
+ attr &= PCI_BASE_ADDRESS_IO_ATTR_MASK;
resource->flags |= IORESOURCE_IO;
+ /* I don't want to deal with 32bit I/O resources */
resource->limit = 0xffff;
}
else {
/* A Memory mapped base address */
- type = size & (~PCI_BASE_ADDRESS_MEM_MASK);
- resource->size = (~(size &PCI_BASE_ADDRESS_MEM_MASK)) +1;
- resource->align = log2(resource->size);
- resource->gran = resource->align;
+ attr &= PCI_BASE_ADDRESS_MEM_ATTR_MASK;
resource->flags |= IORESOURCE_MEM;
- if (type & PCI_BASE_ADDRESS_MEM_PREFETCH) {
+ if (attr & PCI_BASE_ADDRESS_MEM_PREFETCH) {
resource->flags |= IORESOURCE_PREFETCH;
}
- type &= PCI_BASE_ADDRESS_MEM_TYPE_MASK;
- if (type == PCI_BASE_ADDRESS_MEM_TYPE_32) {
+ attr &= PCI_BASE_ADDRESS_MEM_LIMIT_MASK;
+ if (attr == PCI_BASE_ADDRESS_MEM_LIMIT_32) {
/* 32bit limit */
resource->limit = 0xffffffffUL;
}
- else if (type == PCI_BASE_ADDRESS_MEM_TYPE_1M) {
+ else if (attr == PCI_BASE_ADDRESS_MEM_LIMIT_1M) {
/* 1MB limit */
resource->limit = 0x000fffffUL;
}
- else if (type == PCI_BASE_ADDRESS_MEM_TYPE_64) {
- unsigned long index_hi;
- /* 64bit limit
- * For now just treat this as a 32bit limit
- */
- index_hi = index + 4;
- resource->limit = 0xffffffffUL;
+ else if (attr == PCI_BASE_ADDRESS_MEM_LIMIT_64) {
+ /* 64bit limit */
+ resource->limit = 0xffffffffffffffffULL;
resource->flags |= IORESOURCE_PCI64;
- addr = pci_read_config32( dev, index_hi);
- /* get the extended size */
- pci_write_config32(dev, index_hi, 0xffffffffUL);
- size = pci_read_config32( dev, index_hi);
-
- /* get the minimum value the bar can be set to */
- pci_write_config32(dev, index_hi, 0);
- base = pci_read_config32(dev, index_hi);
-
- /* restore addr */
- pci_write_config32(dev, index_hi, addr);
-
- if ((size == 0xffffffff) && (base == 0)) {
- /* Clear the top half of the bar */
- pci_write_config32(dev, index_hi, 0);
- }
- else {
- printk_err("%s Unable to handle 64-bit address\n",
- dev_path(dev));
- resource->flags = IORESOURCE_PCI64;
- }
- }
+ }
else {
/* Invalid value */
resource->flags = 0;
}
}
- /* dev->size holds the flags... */
+ /* Don't let the limit exceed which bits can move */
+ if (resource->limit > limit) {
+ resource->limit = limit;
+ }
+#if 0
+ if (resource->flags) {
+ printk_debug("%s %02x ->",
+ dev_path(dev), resource->index);
+ printk_debug(" value: 0x%08Lx zeroes: 0x%08Lx ones: 0x%08Lx attr: %08lx\n",
+ value, zeroes, ones, attr);
+ printk_debug(
+ "%s %02x -> size: 0x%08Lx max: 0x%08Lx %s\n ",
+ dev_path(dev),
+ resource->index,
+ resource->size, resource->limit,
+ resource_type(resource));
+ }
+#endif
+
return resource;
}
+static void pci_get_rom_resource(struct device *dev, unsigned long index)
+{
+ struct resource *resource;
+ unsigned long value;
+ resource_t moving, limit;
+
+ if ((dev->on_mainboard) && (dev->rom_address == 0)) {
+ //skip it if rom_address is not set in MB Config.lb
+ return;
+ }
+
+ /* Initialize the resources to nothing */
+ resource = new_resource(dev, index);
+
+ /* Get the initial value */
+ value = pci_read_config32(dev, index);
+
+ /* See which bits move */
+ moving = pci_moving_config32(dev, index);
+ /* clear the Enable bit */
+ moving = moving & ~PCI_ROM_ADDRESS_ENABLE;
+
+ /* Find the resource constraints.
+ *
+ * Start by finding the bits that move. From there:
+ * - Size is the least significant bit of the bits that move.
+ * - Limit is all of the bits that move plus all of the lower bits.
+ * See PCI Spec 6.2.5.1 ...
+ */
+ limit = 0;
+
+ if (moving) {
+ resource->size = 1;
+ resource->align = resource->gran = 0;
+ while (!(moving & resource->size)) {
+ resource->size <<= 1;
+ resource->align += 1;
+ resource->gran += 1;
+ }
+ resource->limit = limit = moving | (resource->size - 1);
+ }
+
+ if (moving == 0) {
+ if (value != 0) {
+ printk_debug("%s register %02x(%08x), read-only ignoring it\n",
+ dev_path(dev), index, value);
+ }
+ resource->flags = 0;
+ } else {
+ resource->flags |= IORESOURCE_MEM | IORESOURCE_READONLY;
+ }
+
+ /* for on board device with embedded ROM image, the ROM image is at
+ * fixed address specified in the Config.lb, the dev->rom_address is
+ * inited by driver_pci_onboard_ops::enable_dev() */
+ if ((dev->on_mainboard) && (dev->rom_address != 0)) {
+ resource->base = dev->rom_address;
+ resource->flags |= IORESOURCE_MEM | IORESOURCE_READONLY |
+ IORESOURCE_ASSIGNED | IORESOURCE_FIXED;
+ }
+
+ compact_resources(dev);
+}
+
/** Read the base address registers for a given device.
* @param dev Pointer to the dev structure
* @param howmany How many registers to read (6 for device, 2 for bridge)
{
unsigned long index;
- for (index = PCI_BASE_ADDRESS_0; (index < PCI_BASE_ADDRESS_0 + (howmany << 2)); ) {
+ for(index = PCI_BASE_ADDRESS_0; (index < PCI_BASE_ADDRESS_0 + (howmany << 2)); ) {
struct resource *resource;
resource = pci_get_resource(dev, index);
index += (resource->flags & IORESOURCE_PCI64)?8:4;
}
+
compact_resources(dev);
}
-static void pci_bridge_read_bases(struct device *dev)
+static void pci_set_resource(struct device *dev, struct resource *resource);
+
+static void pci_record_bridge_resource(
+ struct device *dev, resource_t moving,
+ unsigned index, unsigned long mask, unsigned long type)
{
+ /* Initiliaze the constraints on the current bus */
struct resource *resource;
+ resource = 0;
+ if (moving) {
+ unsigned long gran;
+ resource_t step;
+ resource = new_resource(dev, index);
+ resource->size = 0;
+ gran = 0;
+ step = 1;
+ while((moving & step) == 0) {
+ gran += 1;
+ step <<= 1;
+ }
+ resource->gran = gran;
+ resource->align = gran;
+ resource->limit = moving | (step - 1);
+ resource->flags = type | IORESOURCE_PCI_BRIDGE;
+ compute_allocate_resource(&dev->link[0], resource, mask, type);
+ /* If there is nothing behind the resource,
+ * clear it and forget it.
+ */
+ if (resource->size == 0) {
+ resource->base = moving;
+ resource->flags |= IORESOURCE_ASSIGNED;
+ resource->flags &= ~IORESOURCE_STORED;
+ pci_set_resource(dev, resource);
+ resource->flags = 0;
+ }
+ }
+ return;
+}
+
+static void pci_bridge_read_bases(struct device *dev)
+{
+ resource_t moving_base, moving_limit, moving;
+
+ /* See if the bridge I/O resources are implemented */
+ moving_base = ((uint32_t)pci_moving_config8(dev, PCI_IO_BASE)) << 8;
+ moving_base |= ((uint32_t)pci_moving_config16(dev, PCI_IO_BASE_UPPER16)) << 16;
+
+ moving_limit = ((uint32_t)pci_moving_config8(dev, PCI_IO_LIMIT)) << 8;
+ moving_limit |= ((uint32_t)pci_moving_config16(dev, PCI_IO_LIMIT_UPPER16)) << 16;
- /* FIXME handle bridges without some of the optional resources */
+ moving = moving_base & moving_limit;
/* Initialize the io space constraints on the current bus */
- resource = get_resource(dev, PCI_IO_BASE);
- resource->size = 0;
- resource->align = log2(PCI_IO_BRIDGE_ALIGN);
- resource->gran = log2(PCI_IO_BRIDGE_ALIGN);
- resource->limit = 0xffffUL;
- resource->flags |= IORESOURCE_IO | IORESOURCE_PCI_BRIDGE;
- compute_allocate_resource(&dev->link[0], resource,
- IORESOURCE_IO, IORESOURCE_IO);
+ pci_record_bridge_resource(
+ dev, moving, PCI_IO_BASE,
+ IORESOURCE_IO, IORESOURCE_IO);
+
+
+ /* See if the bridge prefmem resources are implemented */
+ moving_base = ((resource_t)pci_moving_config16(dev, PCI_PREF_MEMORY_BASE)) << 16;
+ moving_base |= ((resource_t)pci_moving_config32(dev, PCI_PREF_BASE_UPPER32)) << 32;
+ moving_limit = ((resource_t)pci_moving_config16(dev, PCI_PREF_MEMORY_LIMIT)) << 16;
+ moving_limit |= ((resource_t)pci_moving_config32(dev, PCI_PREF_LIMIT_UPPER32)) << 32;
+
+ moving = moving_base & moving_limit;
/* Initiliaze the prefetchable memory constraints on the current bus */
- resource = get_resource(dev, PCI_PREF_MEMORY_BASE);
- resource->size = 0;
- resource->align = log2(PCI_MEM_BRIDGE_ALIGN);
- resource->gran = log2(PCI_MEM_BRIDGE_ALIGN);
- resource->limit = 0xffffffffUL;
- resource->flags = IORESOURCE_MEM | IORESOURCE_PREFETCH | IORESOURCE_PCI_BRIDGE;
- resource->index = PCI_PREF_MEMORY_BASE;
- compute_allocate_resource(&dev->link[0], resource,
- IORESOURCE_MEM | IORESOURCE_PREFETCH,
- IORESOURCE_MEM | IORESOURCE_PREFETCH);
+ pci_record_bridge_resource(
+ dev, moving, PCI_PREF_MEMORY_BASE,
+ IORESOURCE_MEM | IORESOURCE_PREFETCH,
+ IORESOURCE_MEM | IORESOURCE_PREFETCH);
+
+
+ /* See if the bridge mem resources are implemented */
+ moving_base = ((uint32_t)pci_moving_config16(dev, PCI_MEMORY_BASE)) << 16;
+ moving_limit = ((uint32_t)pci_moving_config16(dev, PCI_MEMORY_LIMIT)) << 16;
+
+ moving = moving_base & moving_limit;
/* Initialize the memory resources on the current bus */
- resource = get_resource(dev, PCI_MEMORY_BASE);
- resource->size = 0;
- resource->align = log2(PCI_MEM_BRIDGE_ALIGN);
- resource->gran = log2(PCI_MEM_BRIDGE_ALIGN);
- resource->limit = 0xffffffffUL;
- resource->flags = IORESOURCE_MEM | IORESOURCE_PCI_BRIDGE;
- compute_allocate_resource(&dev->link[0], resource,
- IORESOURCE_MEM | IORESOURCE_PREFETCH,
- IORESOURCE_MEM);
+ pci_record_bridge_resource(
+ dev, moving, PCI_MEMORY_BASE,
+ IORESOURCE_MEM | IORESOURCE_PREFETCH,
+ IORESOURCE_MEM);
compact_resources(dev);
}
void pci_dev_read_resources(struct device *dev)
{
- uint32_t addr;
-
pci_read_bases(dev, 6);
-
- addr = pci_read_config32(dev, PCI_ROM_ADDRESS);
- dev->rom_address = (addr == 0xffffffff)? 0 : addr;
+ pci_get_rom_resource(dev, PCI_ROM_ADDRESS);
}
void pci_bus_read_resources(struct device *dev)
{
- uint32_t addr;
-
pci_bridge_read_bases(dev);
pci_read_bases(dev, 2);
-
- addr = pci_read_config32(dev, PCI_ROM_ADDRESS1);
- dev->rom_address = (addr == 0xffffffff)? 0 : addr;
-}
-
-/**
- * @brief round a number up to an alignment.
- * @param val the starting value
- * @param roundup Alignment as a power of two
- * @returns rounded up number
- */
-static unsigned long round(unsigned long val, unsigned long roundup)
-{
- /* ROUNDUP MUST BE A POWER OF TWO. */
- unsigned long inverse;
- inverse = ~(roundup - 1);
- val += (roundup - 1);
- val &= inverse;
- return val;
+ pci_get_rom_resource(dev, PCI_ROM_ADDRESS1);
}
static void pci_set_resource(struct device *dev, struct resource *resource)
{
- unsigned long base, limit;
- unsigned char buf[10];
- unsigned long gran;
+ resource_t base, end;
/* Make certain the resource has actually been set */
-
if (!(resource->flags & IORESOURCE_ASSIGNED)) {
- printk_err("ERROR: %s %02x not allocated\n",
- dev_path(dev), resource->index);
+ printk_err("ERROR: %s %02x %s size: 0x%010Lx not assigned\n",
+ dev_path(dev), resource->index,
+ resource_type(resource),
+ resource->size);
return;
}
return;
}
+ /* If the resources is substractive don't worry about it */
+ if (resource->flags & IORESOURCE_SUBTRACTIVE) {
+ return;
+ }
+
/* Only handle PCI memory and IO resources for now */
if (!(resource->flags & (IORESOURCE_MEM |IORESOURCE_IO)))
return;
- if (resource->flags & IORESOURCE_MEM) {
- dev->command |= PCI_COMMAND_MEMORY;
- }
- if (resource->flags & IORESOURCE_IO) {
- dev->command |= PCI_COMMAND_IO;
- }
- if (resource->flags & IORESOURCE_PCI_BRIDGE) {
- dev->command |= PCI_COMMAND_MASTER;
+ /* Enable the resources in the command register */
+ if (resource->size) {
+ if (resource->flags & IORESOURCE_MEM) {
+ dev->command |= PCI_COMMAND_MEMORY;
+ }
+ if (resource->flags & IORESOURCE_IO) {
+ dev->command |= PCI_COMMAND_IO;
+ }
+ if (resource->flags & IORESOURCE_PCI_BRIDGE) {
+ dev->command |= PCI_COMMAND_MASTER;
+ }
}
-
/* Get the base address */
base = resource->base;
- /* Get the resource granularity */
- gran = 1UL << resource->gran;
-
- /* For a non bridge resource granularity and alignment are the same.
- * For a bridge resource align is the largest needed alignment below
- * the bridge. While the granularity is simply how many low bits of the
- * address cannot be set.
- */
-
- /* Get the limit (rounded up) */
- limit = base + round(resource->size, gran) - 1UL;
+ /* Get the end */
+ end = resource_end(resource);
/* Now store the resource */
resource->flags |= IORESOURCE_STORED;
if (!(resource->flags & IORESOURCE_PCI_BRIDGE)) {
- /* some chipsets allow us to set/clear the IO bit.
- * (e.g. VIA 82c686a.) So set it to be safe) */
- limit = base + resource->size -1;
+ unsigned long base_lo, base_hi;
+ /*
+ * some chipsets allow us to set/clear the IO bit.
+ * (e.g. VIA 82c686a.) So set it to be safe)
+ */
+ base_lo = base & 0xffffffff;
+ base_hi = (base >> 32) & 0xffffffff;
if (resource->flags & IORESOURCE_IO) {
- base |= PCI_BASE_ADDRESS_SPACE_IO;
+ base_lo |= PCI_BASE_ADDRESS_SPACE_IO;
}
- pci_write_config32(dev, resource->index, base & 0xffffffff);
+ pci_write_config32(dev, resource->index, base_lo);
if (resource->flags & IORESOURCE_PCI64) {
- /* FIXME handle real 64bit base addresses */
- pci_write_config32(dev, resource->index + 4, 0);
+ pci_write_config32(dev, resource->index + 4, base_hi);
}
- } else if (resource->index == PCI_IO_BASE) {
- /* set the IO ranges
- * WARNING: we don't really do 32-bit addressing for IO yet!
- */
+ }
+ else if (resource->index == PCI_IO_BASE) {
+ /* set the IO ranges */
compute_allocate_resource(&dev->link[0], resource,
- IORESOURCE_IO, IORESOURCE_IO);
- pci_write_config8(dev, PCI_IO_BASE, base >> 8);
- pci_write_config8(dev, PCI_IO_LIMIT, limit >> 8);
- pci_write_config16(dev, PCI_IO_BASE_UPPER16, 0);
- pci_write_config16(dev, PCI_IO_LIMIT_UPPER16, 0);
- } else if (resource->index == PCI_MEMORY_BASE) {
- /* set the memory range */
+ IORESOURCE_IO, IORESOURCE_IO);
+ pci_write_config8(dev, PCI_IO_BASE, base >> 8);
+ pci_write_config16(dev, PCI_IO_BASE_UPPER16, base >> 16);
+ pci_write_config8(dev, PCI_IO_LIMIT, end >> 8);
+ pci_write_config16(dev, PCI_IO_LIMIT_UPPER16, end >> 16);
+ }
+ else if (resource->index == PCI_MEMORY_BASE) {
+ /* set the memory range */
compute_allocate_resource(&dev->link[0], resource,
- IORESOURCE_MEM | IORESOURCE_PREFETCH,
- IORESOURCE_MEM);
+ IORESOURCE_MEM | IORESOURCE_PREFETCH,
+ IORESOURCE_MEM);
pci_write_config16(dev, PCI_MEMORY_BASE, base >> 16);
- pci_write_config16(dev, PCI_MEMORY_LIMIT, limit >> 16);
- } else if (resource->index == PCI_PREF_MEMORY_BASE) {
- /* set the prefetchable memory range
- * WARNING: we don't really do 64-bit addressing for
- * prefetchable memory yet! */
+ pci_write_config16(dev, PCI_MEMORY_LIMIT, end >> 16);
+ }
+ else if (resource->index == PCI_PREF_MEMORY_BASE) {
+ /* set the prefetchable memory range */
compute_allocate_resource(&dev->link[0], resource,
- IORESOURCE_MEM | IORESOURCE_PREFETCH,
- IORESOURCE_MEM | IORESOURCE_PREFETCH);
- pci_write_config16(dev, PCI_PREF_MEMORY_BASE, base >> 16);
- pci_write_config16(dev, PCI_PREF_MEMORY_LIMIT, limit >> 16);
- pci_write_config32(dev, PCI_PREF_BASE_UPPER32, 0);
- pci_write_config32(dev, PCI_PREF_LIMIT_UPPER32, 0);
- } else {
+ IORESOURCE_MEM | IORESOURCE_PREFETCH,
+ IORESOURCE_MEM | IORESOURCE_PREFETCH);
+ pci_write_config16(dev, PCI_PREF_MEMORY_BASE, base >> 16);
+ pci_write_config32(dev, PCI_PREF_BASE_UPPER32, base >> 32);
+ pci_write_config16(dev, PCI_PREF_MEMORY_LIMIT, end >> 16);
+ pci_write_config32(dev, PCI_PREF_LIMIT_UPPER32, end >> 32);
+ }
+ else {
/* Don't let me think I stored the resource */
resource->flags &= ~IORESOURCE_STORED;
printk_err("ERROR: invalid resource->index %x\n",
- resource->index);
+ resource->index);
}
-
- buf[0] = '\0';
- if (resource->flags & IORESOURCE_PCI_BRIDGE) {
- sprintf(buf, "bus %d ", dev->link[0].secondary);
- }
- printk_debug("%s %02x <- [0x%08lx - 0x%08lx] %s%s\n",
- dev_path(dev), resource->index, resource->base,
- limit, buf,
- (resource->flags & IORESOURCE_IO)? "io":
- (resource->flags & IORESOURCE_PREFETCH)? "prefmem": "mem");
+ report_resource_stored(dev, resource, "");
return;
}
uint8_t line;
last = &dev->resource[dev->resources];
- for (resource = &dev->resource[0]; resource < last; resource++) {
+
+ for(resource = &dev->resource[0]; resource < last; resource++) {
pci_set_resource(dev, resource);
}
-
- for (link = 0; link < dev->links; link++) {
+ for(link = 0; link < dev->links; link++) {
struct bus *bus;
bus = &dev->link[link];
if (bus->children) {
void pci_dev_enable_resources(struct device *dev)
{
+ const struct pci_operations *ops;
uint16_t command;
+
+ /* Set the subsystem vendor and device id for mainboard devices */
+ ops = ops_pci(dev);
+ if (dev->on_mainboard && ops && ops->set_subsystem) {
+ printk_debug("%s subsystem <- %02x/%02x\n",
+ dev_path(dev),
+ MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID,
+ MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID);
+ ops->set_subsystem(dev,
+ MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID,
+ MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID);
+ }
command = pci_read_config16(dev, PCI_COMMAND);
command |= dev->command;
- command |= (PCI_COMMAND_PARITY + PCI_COMMAND_SERR); /* error check */
printk_debug("%s cmd <- %02x\n", dev_path(dev), command);
pci_write_config16(dev, PCI_COMMAND, command);
-
- enable_childrens_resources(dev);
}
void pci_bus_enable_resources(struct device *dev)
{
uint16_t ctrl;
+ /* enable IO in command register if there is VGA card
+ * connected with (even it does not claim IO resource) */
+ if (dev->link[0].bridge_ctrl & PCI_BRIDGE_CTL_VGA)
+ dev->command |= PCI_COMMAND_IO;
ctrl = pci_read_config16(dev, PCI_BRIDGE_CONTROL);
ctrl |= dev->link[0].bridge_ctrl;
ctrl |= (PCI_BRIDGE_CTL_PARITY + PCI_BRIDGE_CTL_SERR); /* error check */
pci_write_config16(dev, PCI_BRIDGE_CONTROL, ctrl);
pci_dev_enable_resources(dev);
+
+ enable_childrens_resources(dev);
+}
+
+void pci_bus_reset(struct bus *bus)
+{
+ unsigned ctl;
+ ctl = pci_read_config16(bus->dev, PCI_BRIDGE_CONTROL);
+ ctl |= PCI_BRIDGE_CTL_BUS_RESET;
+ pci_write_config16(bus->dev, PCI_BRIDGE_CONTROL, ctl);
+ mdelay(10);
+ ctl &= ~PCI_BRIDGE_CTL_BUS_RESET;
+ pci_write_config16(bus->dev, PCI_BRIDGE_CONTROL, ctl);
+ delay(1);
+}
+
+void pci_dev_set_subsystem(device_t dev, unsigned vendor, unsigned device)
+{
+ pci_write_config32(dev, PCI_SUBSYSTEM_VENDOR_ID,
+ ((device & 0xffff) << 16) | (vendor & 0xffff));
+}
+
+/** default handler: only runs the relevant pci bios. */
+void pci_dev_init(struct device *dev)
+{
+#if CONFIG_PCI_ROM_RUN == 1 || CONFIG_VGA_ROM_RUN == 1
+ void run_bios(struct device * dev, unsigned long addr);
+ struct rom_header *rom, *ram;
+
+#if CONFIG_PCI_ROM_RUN != 1
+ /* We want to execute VGA option ROMs when CONFIG_VGA_ROM_RUN
+ * is set but CONFIG_PCI_ROM_RUN is not. In this case we skip
+ * all other option ROM types.
+ */
+ if ((dev->class>>8)!=PCI_CLASS_DISPLAY_VGA)
+ return;
+#endif
+
+ rom = pci_rom_probe(dev);
+ if (rom == NULL)
+ return;
+
+ ram = pci_rom_load(dev, rom);
+ if (ram == NULL)
+ return;
+
+ run_bios(dev, (unsigned long)ram);
+
+#if CONFIG_CONSOLE_VGA == 1
+ /* vga_inited is a trigger of the VGA console code. */
+ if ((dev->class>>8) == PCI_CLASS_DISPLAY_VGA) {
+ extern int vga_inited;
+ vga_inited = 1;
+ }
+#endif /* CONFIG_CONSOLE_VGA */
+#endif /* CONFIG_PCI_ROM_RUN || CONFIG_VGA_ROM_RUN */
}
/** Default device operation for PCI devices */
+static struct pci_operations pci_dev_ops_pci = {
+ .set_subsystem = pci_dev_set_subsystem,
+};
+
struct device_operations default_pci_ops_dev = {
.read_resources = pci_dev_read_resources,
.set_resources = pci_dev_set_resources,
.enable_resources = pci_dev_enable_resources,
- .init = 0,
+ .init = pci_dev_init,
.scan_bus = 0,
+ .enable = 0,
+ .ops_pci = &pci_dev_ops_pci,
};
/** Default device operations for PCI bridges */
+static struct pci_operations pci_bus_ops_pci = {
+ .set_subsystem = 0,
+};
+
struct device_operations default_pci_ops_bus = {
.read_resources = pci_bus_read_resources,
.set_resources = pci_dev_set_resources,
.enable_resources = pci_bus_enable_resources,
.init = 0,
.scan_bus = pci_scan_bridge,
+ .enable = 0,
+ .reset_bus = pci_bus_reset,
+ .ops_pci = &pci_bus_ops_pci,
};
+/**
+ * @brief Detect the type of downstream bridge
+ *
+ * This function is a heuristic to detect which type
+ * of bus is downstream of a pci to pci bridge. This
+ * functions by looking for various capability blocks
+ * to figure out the type of downstream bridge. PCI-X
+ * PCI-E, and Hypertransport all seem to have appropriate
+ * capabilities.
+ *
+ * When only a PCI-Express capability is found the type
+ * is examined to see which type of bridge we have.
+ *
+ * @param dev
+ *
+ * @return appropriate bridge operations
+ */
+static struct device_operations *get_pci_bridge_ops(device_t dev)
+{
+ unsigned pos;
+
+#if CONFIG_PCIX_PLUGIN_SUPPORT == 1
+ pos = pci_find_capability(dev, PCI_CAP_ID_PCIX);
+ if (pos) {
+ printk_debug("%s subbordinate bus PCI-X\n", dev_path(dev));
+ return &default_pcix_ops_bus;
+ }
+#endif
+#if CONFIG_AGP_PLUGIN_SUPPORT == 1
+ /* How do I detect an PCI to AGP bridge? */
+#endif
+#if CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT == 1
+ pos = 0;
+ while((pos = pci_find_next_capability(dev, PCI_CAP_ID_HT, pos))) {
+ unsigned flags;
+ flags = pci_read_config16(dev, pos + PCI_CAP_FLAGS);
+ if ((flags >> 13) == 1) {
+ /* Host or Secondary Interface */
+ printk_debug("%s subbordinate bus Hypertransport\n",
+ dev_path(dev));
+ return &default_ht_ops_bus;
+ }
+ }
+#endif
+#if CONFIG_PCIEXP_PLUGIN_SUPPORT == 1
+ pos = pci_find_capability(dev, PCI_CAP_ID_PCIE);
+ if (pos) {
+ unsigned flags;
+ flags = pci_read_config16(dev, pos + PCI_EXP_FLAGS);
+ switch((flags & PCI_EXP_FLAGS_TYPE) >> 4) {
+ case PCI_EXP_TYPE_ROOT_PORT:
+ case PCI_EXP_TYPE_UPSTREAM:
+ case PCI_EXP_TYPE_DOWNSTREAM:
+ printk_debug("%s subbordinate bus PCI Express\n",
+ dev_path(dev));
+ return &default_pciexp_ops_bus;
+ case PCI_EXP_TYPE_PCI_BRIDGE:
+ printk_debug("%s subbordinate PCI\n",
+ dev_path(dev));
+ return &default_pci_ops_bus;
+ default:
+ break;
+ }
+ }
+#endif
+ return &default_pci_ops_bus;
+}
+
/**
* @brief Set up PCI device operation
*
static void set_pci_ops(struct device *dev)
{
struct pci_driver *driver;
-
if (dev->ops) {
return;
}
/* Look through the list of setup drivers and find one for
- * this pci device */
- for (driver = &pci_drivers[0]; driver != &epci_drivers[0]; driver++) {
+ * this pci device
+ */
+ for(driver = &pci_drivers[0]; driver != &epci_drivers[0]; driver++) {
if ((driver->vendor == dev->vendor) &&
- (driver->device == dev->device)) {
+ (driver->device == dev->device))
+ {
dev->ops = driver->ops;
-
- printk_debug("%s [%04x/%04x] %sops\n", dev_path(dev),
- driver->vendor, driver->device,
- (driver->ops->scan_bus?"bus ":""));
-
+ printk_spew("%s [%04x/%04x] %sops\n",
+ dev_path(dev),
+ driver->vendor, driver->device,
+ (driver->ops->scan_bus?"bus ":""));
return;
}
}
-#if 0
- extern struct pci_driver generic_vga_driver;
- /* TODO: Install generic VGA driver for VGA devices, base on the
- * class ID */
- if ((dev->class >> 8) == PCI_CLASS_DISPLAY_VGA) {
- printk_debug("setting up generic VGA driver\n");
- dev->ops = generic_vga_driver.ops;
- return;
- }
-#endif
-
/* If I don't have a specific driver use the default operations */
switch(dev->hdr_type & 0x7f) { /* header type */
case PCI_HEADER_TYPE_NORMAL: /* standard header */
case PCI_HEADER_TYPE_BRIDGE:
if ((dev->class >> 8) != PCI_CLASS_BRIDGE_PCI)
goto bad;
- dev->ops = &default_pci_ops_bus;
+ dev->ops = get_pci_bridge_ops(dev);
break;
+#if CONFIG_CARDBUS_PLUGIN_SUPPORT == 1
+ case PCI_HEADER_TYPE_CARDBUS:
+ dev->ops = &default_cardbus_ops_bus;
+ break;
+#endif
default:
bad:
if (dev->enabled) {
printk_err("%s [%04x/%04x/%06x] has unknown header "
- "type %02x, ignoring.\n",
- dev_path(dev),
- dev->vendor, dev->device,
- dev->class >> 8, dev->hdr_type);
+ "type %02x, ignoring.\n",
+ dev_path(dev),
+ dev->vendor, dev->device,
+ dev->class >> 8, dev->hdr_type);
}
}
return;
}
+
+
/**
- * @brief Find a specific device structure on a list of device structures
+ * @brief See if we have already allocated a device structure for a given devfn.
*
* Given a linked list of PCI device structures and a devfn number, find the
- * device structure correspond to the devfn.
+ * device structure correspond to the devfn, if present. This function also
+ * removes the device structure from the linked list.
*
* @param list the device structure list
* @param devfn a device/function number
*
- * @return pointer to the device structure found
+ * @return pointer to the device structure found or null of we have not
+ * allocated a device for this devfn yet.
*/
-static struct device *pci_scan_get_dev(struct device **list,
- unsigned int devfn)
+static struct device *pci_scan_get_dev(struct device **list, unsigned int devfn)
{
- struct device *dev = 0;
-
- printk_debug("%s, looking for devfn: %02x.%01x\n", __FUNCTION__,
- devfn >> 3, devfn & 7);
- for (; *list; list = &(*list)->sibling) {
+ struct device *dev;
+ dev = 0;
+ for(; *list; list = &(*list)->sibling) {
if ((*list)->path.type != DEVICE_PATH_PCI) {
printk_err("child %s not a pci device\n",
- dev_path(*list));
+ dev_path(*list));
continue;
}
if ((*list)->path.u.pci.devfn == devfn) {
break;
}
}
-
- printk_debug("%s, found dev %08x\n", __FUNCTION__, dev);
-
- /* FIXME: why are we doing this ? Isn't there some order between the
- * structures before ? */
+ /* Just like alloc_dev add the device to the list of device on the bus.
+ * When the list of devices was formed we removed all of the parents
+ * children, and now we are interleaving static and dynamic devices in
+ * order on the bus.
+ */
if (dev) {
device_t child;
/* Find the last child of our parent */
- for (child = dev->bus->children; child && child->sibling; ) {
+ for(child = dev->bus->children; child && child->sibling; ) {
child = child->sibling;
}
/* Place the device on the list of children of it's parent. */
return dev;
}
-/**
- * @brief Scan a PCI bus
+/**
+ * @brief Scan a PCI bus.
+ *
+ * Determine the existence of a given PCI device.
+ *
+ * @param bus pointer to the bus structure
+ * @param devfn to look at
+ *
+ * @return The device structure for hte device (if found)
+ * or the NULL if no device is found.
+ */
+device_t pci_probe_dev(device_t dev, struct bus *bus, unsigned devfn)
+{
+ uint32_t id, class;
+ uint8_t hdr_type;
+
+ /* Detect if a device is present */
+ if (!dev) {
+ struct device dummy;
+ dummy.bus = bus;
+ dummy.path.type = DEVICE_PATH_PCI;
+ dummy.path.u.pci.devfn = devfn;
+ id = pci_read_config32(&dummy, PCI_VENDOR_ID);
+ /* Have we found somthing?
+ * Some broken boards return 0 if a slot is empty.
+ */
+ if ( (id == 0xffffffff) || (id == 0x00000000) ||
+ (id == 0x0000ffff) || (id == 0xffff0000))
+ {
+ printk_spew("%s, bad id 0x%x\n", dev_path(&dummy), id);
+ return NULL;
+ }
+ dev = alloc_dev(bus, &dummy.path);
+ }
+ else {
+ /* Enable/disable the device. Once we have
+ * found the device specific operations this
+ * operations we will disable the device with
+ * those as well.
+ *
+ * This is geared toward devices that have subfunctions
+ * that do not show up by default.
+ *
+ * If a device is a stuff option on the motherboard
+ * it may be absent and enable_dev must cope.
+ *
+ */
+ /* Run the magice enable sequence for the device */
+ if (dev->chip_ops && dev->chip_ops->enable_dev) {
+ dev->chip_ops->enable_dev(dev);
+ }
+ /* Now read the vendor and device id */
+ id = pci_read_config32(dev, PCI_VENDOR_ID);
+
+
+ /* If the device does not have a pci id disable it.
+ * Possibly this is because we have already disabled
+ * the device. But this also handles optional devices
+ * that may not always show up.
+ */
+ /* If the chain is fully enumerated quit */
+ if ( (id == 0xffffffff) || (id == 0x00000000) ||
+ (id == 0x0000ffff) || (id == 0xffff0000))
+ {
+ if (dev->enabled) {
+ printk_info("Disabling static device: %s\n",
+ dev_path(dev));
+ dev->enabled = 0;
+ }
+ return dev;
+ }
+ }
+ /* Read the rest of the pci configuration information */
+ hdr_type = pci_read_config8(dev, PCI_HEADER_TYPE);
+ class = pci_read_config32(dev, PCI_CLASS_REVISION);
+
+ /* Store the interesting information in the device structure */
+ dev->vendor = id & 0xffff;
+ dev->device = (id >> 16) & 0xffff;
+ dev->hdr_type = hdr_type;
+ /* class code, the upper 3 bytes of PCI_CLASS_REVISION */
+ dev->class = class >> 8;
+
+
+ /* Architectural/System devices always need to
+ * be bus masters.
+ */
+ if ((dev->class >> 16) == PCI_BASE_CLASS_SYSTEM) {
+ dev->command |= PCI_COMMAND_MASTER;
+ }
+ /* Look at the vendor and device id, or at least the
+ * header type and class and figure out which set of
+ * configuration methods to use. Unless we already
+ * have some pci ops.
+ */
+ set_pci_ops(dev);
+
+ /* Now run the magic enable/disable sequence for the device */
+ if (dev->ops && dev->ops->enable) {
+ dev->ops->enable(dev);
+ }
+
+
+ /* Display the device and error if we don't have some pci operations
+ * for it.
+ */
+ printk_debug("%s [%04x/%04x] %s%s\n",
+ dev_path(dev),
+ dev->vendor, dev->device,
+ dev->enabled?"enabled": "disabled",
+ dev->ops?"" : " No operations"
+ );
+
+ return dev;
+}
+
+/**
+ * @brief Scan a PCI bus.
*
* Determine the existence of devices and bridges on a PCI bus. If there are
* bridges on the bus, recursively scan the buses behind the bridges.
*
* @return The maximum bus number found, after scanning all subordinate busses
*/
-unsigned int pci_scan_bus(struct bus *bus, unsigned min_devfn,
- unsigned max_devfn, unsigned int max)
+unsigned int pci_scan_bus(struct bus *bus,
+ unsigned min_devfn, unsigned max_devfn,
+ unsigned int max)
{
unsigned int devfn;
- device_t dev;
device_t old_devices;
device_t child;
- printk_debug("PCI: pci_scan_bus for bus %d\n", bus->secondary);
+#if PCI_BUS_SEGN_BITS
+ printk_debug("PCI: pci_scan_bus for bus %04x:%02x\n", bus->secondary >> 8, bus->secondary & 0xff);
+#else
+ printk_debug("PCI: pci_scan_bus for bus %02x\n", bus->secondary);
+#endif
old_devices = bus->children;
bus->children = 0;
post_code(0x24);
-
/* probe all devices/functions on this bus with some optimization for
- * non-existence and single funcion devices */
+ * non-existence and single funcion devices
+ */
for (devfn = min_devfn; devfn <= max_devfn; devfn++) {
- uint32_t id, class;
- uint8_t hdr_type;
+ device_t dev;
- /* device structures for PCI devices associated with static
- * devices are already created during the static device
- * enumeration, find out if it is the case for this devfn */
+ /* First thing setup the device structure */
dev = pci_scan_get_dev(&old_devices, devfn);
- if (!dev) {
- /* it's not associated with a static device, detect if
- * this device is present */
- struct device dummy;
- dummy.bus = bus;
- dummy.path.type = DEVICE_PATH_PCI;
- dummy.path.u.pci.devfn = devfn;
- id = pci_read_config32(&dummy, PCI_VENDOR_ID);
- /* some broken boards return 0 if a slot is empty: */
- if ((id == 0xffffffff) || (id == 0x00000000) ||
- (id == 0x0000ffff) || (id == 0xffff0000)) {
- printk_spew("PCI: devfn 0x%x, bad id 0x%x\n",
- devfn, id);
- if (PCI_FUNC(devfn) == 0x00) {
- /* if this is a function 0 device and
- * it is not present, skip to next
- * device */
- devfn += 0x07;
- }
- /* this function in a multi function device is
- * not present, skip to next function */
- continue;
- }
- dev = alloc_dev(bus, &dummy.path);
- } else {
- /* Run the magic enable/disable sequence for the
- * device */
- /* FIXME: What happen if this PCI device listed as
- * static device but does not exist ? This calls
- * some arbitray code without any justification
- * Also, it calls the enable function regardlessly
- * the value of dev->enabled */
- if (dev->chip && dev->chip->control &&
- dev->chip->control->enable_dev) {
- int enabled = dev->enabled;
- dev->enabled = 1;
- dev->chip->control->enable_dev(dev);
- dev->enabled = enabled;
- }
- /* Now read the vendor and device id */
- id = pci_read_config32(dev, PCI_VENDOR_ID);
- }
- /* Read the rest of the pci configuration information */
- hdr_type = pci_read_config8(dev, PCI_HEADER_TYPE);
- class = pci_read_config32(dev, PCI_CLASS_REVISION);
-
- /* Store the interesting information in the device structure */
- dev->vendor = id & 0xffff;
- dev->device = (id >> 16) & 0xffff;
- dev->hdr_type = hdr_type;
- /* class code, the upper 3 bytes of PCI_CLASS_REVISION */
- dev->class = class >> 8;
-
- /* Look at the vendor and device id, or at least the
- * header type and class and figure out which set of
- * configuration methods to use. Unless we already
- * have some pci ops.
+ /* See if a device is present and setup the device
+ * structure.
*/
- set_pci_ops(dev);
- /* Error if we don't have some pci operations for it */
- if (!dev->ops) {
- printk_err("%s No device operations\n",
- dev_path(dev));
- continue;
- }
+ dev = pci_probe_dev(dev, bus, devfn);
- /* Now run the magic enable/disable sequence for the device */
- if (dev->ops && dev->ops->enable) {
- dev->ops->enable(dev);
- } else if (dev->chip && dev->chip->control &&
- dev->chip->control->enable_dev) {
- dev->chip->control->enable_dev(dev);
- }
-
- printk_debug("%s [%04x/%04x] %s\n",
- dev_path(dev),
- dev->vendor, dev->device,
- dev->enabled?"enabled": "disabled");
-
- if (PCI_FUNC(devfn) == 0x00 && (hdr_type & 0x80) != 0x80) {
- /* if this is not a multi function device, don't
- * waste time probe another function.
- * Skip to next device. */
+ /* if this is not a multi function device,
+ * or the device is not present don't waste
+ * time probing another function.
+ * Skip to next device.
+ */
+ if ((PCI_FUNC(devfn) == 0x00) &&
+ (!dev || (dev->enabled && ((dev->hdr_type & 0x80) != 0x80))))
+ {
devfn += 0x07;
}
}
post_code(0x25);
- /* if a child provides scan_bus(), for example a bridge, scan
- * buses behind that child */
- for (child = bus->children; child; child = child->sibling) {
- if (!child->ops->scan_bus) {
- continue;
+ /* Die if any left over static devices are are found.
+ * There's probably a problem in the Config.lb.
+ */
+ if(old_devices) {
+ device_t left;
+ for(left = old_devices; left; left = left->sibling) {
+ printk_err("%s\n", dev_path(left));
}
- max = child->ops->scan_bus(child, max);
+ printk_warning("PCI: Left over static devices. Check your mainboard Config.lb\n");
+ }
+
+ /* For all children that implement scan_bus (i.e. bridges)
+ * scan the bus behind that child.
+ */
+ for(child = bus->children; child; child = child->sibling) {
+ max = scan_bus(child, max);
}
/*
*
* Return how far we've got finding sub-buses.
*/
- printk_debug("PCI: pci_scan_bus returning with max=%02x\n", max);
+ printk_debug("PCI: pci_scan_bus returning with max=%03x\n", max);
post_code(0x55);
return max;
}
+
/**
* @brief Scan a PCI bridge and the buses behind the bridge.
*
*
* @return The maximum bus number found, after scanning all subordinate busses
*/
-unsigned int pci_scan_bridge(struct device *dev, unsigned int max)
+unsigned int do_pci_scan_bridge(struct device *dev, unsigned int max,
+ unsigned int (*do_scan_bus)(struct bus *bus,
+ unsigned min_devfn, unsigned max_devfn, unsigned int max))
{
struct bus *bus;
uint32_t buses;
uint16_t cr;
+ printk_spew("%s for %s\n", __func__, dev_path(dev));
+
bus = &dev->link[0];
+ bus->dev = dev;
dev->links = 1;
/* Set up the primary, secondary and subordinate bus numbers. We have
* no idea how many buses are behind this bridge yet, so we set the
- * subordinate bus number to 0xff for the moment. */
+ * subordinate bus number to 0xff for the moment.
+ */
bus->secondary = ++max;
bus->subordinate = 0xff;
pci_write_config16(dev, PCI_COMMAND, 0x0000);
pci_write_config16(dev, PCI_STATUS, 0xffff);
- /* Read the existing primary/secondary/subordinate bus
- * number configuration. */
+ /*
+ * Read the existing primary/secondary/subordinate bus
+ * number configuration.
+ */
buses = pci_read_config32(dev, PCI_PRIMARY_BUS);
/* Configure the bus numbers for this bridge: the configuration
* transactions will not be propagated by the bridge if it is not
- * correctly configured */
+ * correctly configured.
+ */
buses &= 0xff000000;
buses |= (((unsigned int) (dev->bus->secondary) << 0) |
- ((unsigned int) (bus->secondary) << 8) |
- ((unsigned int) (bus->subordinate) << 16));
+ ((unsigned int) (bus->secondary) << 8) |
+ ((unsigned int) (bus->subordinate) << 16));
pci_write_config32(dev, PCI_PRIMARY_BUS, buses);
- /* Now we can scan all subordinate buses i.e. the buses behind the
- * bridge */
- max = pci_scan_bus(bus, 0x00, 0xff, max);
+ /* Now we can scan all subordinate buses
+ * i.e. the bus behind the bridge.
+ */
+ max = do_scan_bus(bus, 0x00, 0xff, max);
/* We know the number of buses behind this bridge. Set the subordinate
- * bus number to its real value */
+ * bus number to its real value.
+ */
bus->subordinate = max;
buses = (buses & 0xff00ffff) |
((unsigned int) (bus->subordinate) << 16);
pci_write_config32(dev, PCI_PRIMARY_BUS, buses);
pci_write_config16(dev, PCI_COMMAND, cr);
-
- printk_spew("%s returns max %d\n", __FUNCTION__, max);
+
+ printk_spew("%s returns max %d\n", __func__, max);
return max;
}
+/**
+ * @brief Scan a PCI bridge and the buses behind the bridge.
+ *
+ * Determine the existence of buses behind the bridge. Set up the bridge
+ * according to the result of the scan.
+ *
+ * This function is the default scan_bus() method for PCI bridge devices.
+ *
+ * @param dev pointer to the bridge device
+ * @param max the highest bus number assgined up to now
+ *
+ * @return The maximum bus number found, after scanning all subordinate busses
+ */
+unsigned int pci_scan_bridge(struct device *dev, unsigned int max)
+{
+ return do_pci_scan_bridge(dev, max, pci_scan_bus);
+}
+
/*
Tell the EISA int controller this int must be level triggered
THIS IS A KLUDGE -- sorry, this needs to get cleaned up.
*/
-static void pci_level_irq(unsigned char intNum)
+void pci_level_irq(unsigned char intNum)
{
unsigned short intBits = inb(0x4d0) | (((unsigned) inb(0x4d1)) << 8);
- printk_spew("%s: current ints are 0x%x\n", __FUNCTION__, intBits);
+ printk_spew("%s: current ints are 0x%x\n", __func__, intBits);
intBits |= (1 << intNum);
- printk_spew("%s: try to set ints 0x%x\n", __FUNCTION__, intBits);
+ printk_spew("%s: try to set ints 0x%x\n", __func__, intBits);
// Write new values
outb((unsigned char) intBits, 0x4d0);
outb((unsigned char) (intBits >> 8), 0x4d1);
/* this seems like an error but is not ... */
-#if 0
- if (inb(0x4d0) != (intBits & 0xf)) {
+#if 1
+ if (inb(0x4d0) != (intBits & 0xff)) {
printk_err("%s: lower order bits are wrong: want 0x%x, got 0x%x\n",
- __FUNCTION__, intBits &0xf, inb(0x4d0));
+ __func__, intBits &0xff, inb(0x4d0));
}
- if (inb(0x4d1) != ((intBits >> 8) & 0xf)) {
+ if (inb(0x4d1) != ((intBits >> 8) & 0xff)) {
printk_err("%s: lower order bits are wrong: want 0x%x, got 0x%x\n",
- __FUNCTION__, (intBits>>8) &0xf, inb(0x4d1));
+ __func__, (intBits>>8) &0xff, inb(0x4d1));
}
#endif
}
projects / coreboot.git / blobdiff