#define drcbendadr (( volatile unsigned long *)0xfffef018)
#define eccctl (( volatile unsigned char *)0xfffef020)
#define dbctl (( volatile unsigned char *)0xfffef040)
-void
-setupsc520(void){
- volatile unsigned char *cp;
- volatile unsigned short *sp;
- volatile unsigned long *edi;
- volatile unsigned long *par;
-
- /* do this to see if MMCR will start acting right.
- * we suspect you have to do SOMETHING to get things going.
- * I'm really starting to hate this processor.
- */
- /* no, that did not help. I wonder what will?
- * outl(0x800df0cb, 0xfffc);
- */
- /* well, this is special! You have to do SHORT writes to the locations,
- * even though they are CHAR in size and CHAR aligned and technically, a
- * SHORT write will result in -- yoo ha! -- over writing the next location!
- * Thanks to the u-boot guys for a reference code I can use.
- * with these short pointers, it now reliably comes up after power cycle
- * with printk. Ah yi yi.
- */
- /* turn off the write buffer*/
- /* per the note above, make this a short? Let's try it.
- */
- sp = (unsigned short *)0xfffef040;
- *sp = 0;
-
- // moved to auto.c by stepan
- setup_pars();
-#if 0
- /* as per the book: */
- /* PAR register setup */
- /* set up the PAR registers as they are on the MSM586SEG */
- par = (unsigned long *) 0xfffef088;
+void setupsc520(void)
+{
+ volatile unsigned char *cp;
+ volatile unsigned short *sp;
+ volatile unsigned long *edi;
+
+ /* do this to see if MMCR will start acting right. we suspect
+ * you have to do SOMETHING to get things going. I'm really
+ * starting to hate this processor.
+ */
- /* NOTE: move this to mainboard.c ASAP */
-#if 1
-
-
- *par++ = 0x607c00a0; /*PAR0: PCI:Base 0xa0000; size 0x1f000:*/
- *par++ = 0x480400d8; /*PAR1: GP BUS MEM:CS2:Base 0xd8, size 0x4:*/
- *par++ = 0x340100ea; /*PAR2: GP BUS IO:CS5:Base 0xea, size 0x1:*/
- *par++ = 0x380701f0; /*PAR3: GP BUS IO:CS6:Base 0x1f0, size 0x7:*/
- *par++ = 0x3c0003f6; /*PAR4: GP BUS IO:CS7:Base 0x3f6, size 0x0:*/
- *par++ = 0x35ff0400; /*PAR5: GP BUS IO:CS5:Base 0x400, size 0xff:*/
- *par++ = 0x35ff0600; /*PAR6: GP BUS IO:CS5:Base 0x600, size 0xff:*/
- *par++ = 0x35ff0800; /*PAR7: GP BUS IO:CS5:Base 0x800, size 0xff:*/
- *par++ = 0x35ff0a00; /*PAR8: GP BUS IO:CS5:Base 0xa00, size 0xff:*/
- *par++ = 0x35ff0e00; /*PAR9: GP BUS IO:CS5:Base 0xe00, size 0xff:*/
- *par++ = 0x34fb0104; /*PAR10: GP BUS IO:CS5:Base 0x104, size 0xfb:*/
- *par++ = 0x35af0200; /*PAR11: GP BUS IO:CS5:Base 0x200, size 0xaf:*/
- *par++ = 0x341f03e0; /*PAR12: GP BUS IO:CS5:Base 0x3e0, size 0x1f:*/
- *par++ = 0xe41c00c0; /*PAR13: SDRAM:code:cache:nowrite:Base 0xc0000, size 0x7000:*/
- *par++ = 0x545c00c8; /*PAR14: GP BUS MEM:CS5:Base 0xc8, size 0x5c:*/
-#else
- par += 15;
-#endif
- *par++ = 0x8a020200; /*PAR15: BOOTCS:code:nocache:write:Base 0x2000000, size 0x80000:*/
-#endif
+ /* no, that did not help. I wonder what will?
+ * outl(0x800df0cb, 0xfffc);
+ */
+
+ /* well, this is special! You have to do SHORT writes to the
+ * locations, even though they are CHAR in size and CHAR aligned
+ * and technically, a SHORT write will result in -- yoo ha! --
+ * over writing the next location! Thanks to the u-boot guys
+ * for a reference code I can use. with these short pointers,
+ * it now reliably comes up after power cycle with printk. Ah yi
+ * yi.
+ */
+
+ /* turn off the write buffer*/
+ /* per the note above, make this a short? Let's try it. */
+ sp = (unsigned short *)0xfffef040;
+ *sp = 0;
+ /* as per the book: */
+ /* PAR register setup */
+ /* set up the PAR registers as they are on the MSM586SEG */
+ /* moved to auto.c by Stepan, Ron says: */
+ /* NOTE: move this to mainboard.c ASAP */
+ setup_pars();
+
/* CPCSF register */
-
sp = (unsigned short *)0xfffefc24;
*sp = 0xfe;
outb(0x55, 0x80);
#endif
-/*; set the uart baud rate clocks to the normal 1.8432 MHz.*/
-/* enable interrupts here? Why not? */
+ /* set the uart baud rate clocks to the normal 1.8432 MHz.*/
+ /* enable interrupts here? Why not? */
cp = (unsigned char *)0xfffefcc0;
- *cp = 4 | 3; /* uart 1 clock source */
+ *cp = 4 | 3; /* uart 1 clock source */
cp = (unsigned char *)0xfffefcc4;
- *cp = 4; /* uart 2 clock source */
+ *cp = 4; /* uart 2 clock source */
#if 0
/*; set the interrupt mapping registers.*/
cp = (unsigned char *)0x0fffefd51;
*cp = 0x02;
-#endif
-/*; "enumerate" the PCI. Mainly set the interrupt bits on the PCnetFast. */
- outl(0xcf8, 0x08000683c);
- outl(0xcfc, 0xc); /* set the interrupt line */
+#endif
-/*; Set the SC520 PCI host bridge to target mode to allow external*/
-/*; bus mastering events*/
+/* Stepan says: This needs to go to the msm586seg code */
+/* "enumerate" the PCI. Mainly set the interrupt bits on the PCnetFast. */
+ outl(0x08000683c, 0xcf8);
+ outl(0xc, 0xcfc); /* set the interrupt line */
- outl(0x0cf8,0x080000004); /*index the status command register on device 0*/
- outl(0xcfc, 0x2); /*set the memory access enable bit*/
+
+ /* Set the SC520 PCI host bridge to target mode to
+ * allow external bus mastering events
+ */
+ /* index the status command register on device 0*/
+ outl(0x080000004, 0x0cf8);
+ outl(0x2, 0xcfc); /*set the memory access enable bit*/
OUTC(0x0fffef072, 1); /* enable req bits in SYSARBMENB */
-
-
-
}
/* This code is known to work on the digital logic board and on the technologic
* systems ts5300
*/
-int
-staticmem(void){
- volatile unsigned long *zero = (unsigned long *) CACHELINESZ;
+int staticmem(void)
+{
+ volatile unsigned long *zero = (unsigned long *) CACHELINESZ;
+
/* set up 0x18 .. **/
*drcbendadr = 0x88;
*drcmctl = 0x1e;
/* two autorefreshes */
*drcctl = 4;
*zero = 0;
- print_err("one zero out on refresh\r\n");
+ print_debug("one zero out on refresh\r\n");
*zero = 0;
- print_err("two zero out on refresh\r\n");
+ print_debug("two zero out on refresh\r\n");
/* load mode register */
*drcctl = 3;
*zero = 0;
- print_err("DONE the load mode reg\r\n");
+ print_debug("DONE the load mode reg\r\n");
/* normal mode */
*drcctl = 0x0;
*zero = 0;
- print_err("DONE one last write and then turn on refresh etc\r\n");
+ print_debug("DONE one last write and then turn on refresh etc\r\n");
*drcctl = 0x18;
*zero = 0;
- print_err("DONE the normal\r\n");
+ print_debug("DONE the normal\r\n");
*zero = 0xdeadbeef;
if (*zero != 0xdeadbeef)
- print_err("NO LUCK\r\n");
+ print_debug("NO LUCK\r\n");
else
- print_err("did a store and load ...\r\n");
+ print_debug("did a store and load ...\r\n");
//print_err_hex32(*zero);
// print_err(" zero is now "); print_err_hex32(*zero); print_err("\r\n");
}
projects / coreboot.git / blobdiff