Enables the use of ccache for faster builds.
Requires ccache in path.
+config SCONFIG_GENPARSER
+ bool "Generate SCONFIG parser using flex and bison"
+ default n
+ depends on EXPERT
+ help
+ Enable this option if you are working on the sconfig
+ device tree parser and made changes to sconfig.l and
+ sconfig.y.
+ Otherwise, say N.
+
+config USE_OPTION_TABLE
+ bool "Use CMOS for configuration values"
+ default n
+ depends on HAVE_OPTION_TABLE
+ help
+ Enable this option if coreboot shall read options from the "CMOS"
+ NVRAM instead of using hard coded values.
+
endmenu
source src/mainboard/Kconfig
-source src/arch/i386/Kconfig
+
+# This option is used to set the architecture of a mainboard to X86.
+# It is usually set in mainboard/*/Kconfig.
+config ARCH_X86
+ bool
+ default n
+
+if ARCH_X86
+source src/arch/x86/Kconfig
+endif
menu "Chipset"
source src/superio/Kconfig
comment "Devices"
source src/devices/Kconfig
+comment "Embedded Controllers"
+source src/ec/Kconfig
+
+endmenu
+menu "Generic Drivers"
+source src/drivers/Kconfig
endmenu
config PCI_BUS_SEGN_BITS
int
default 0
-config MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
- hex
- default 0x0
-
-config MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
- hex
- default 0x0
-
-config CPU_ADDR_BITS
- int
- default 36
-
-config LOGICAL_CPUS
- bool
- default y
-
config PCI_ROM_RUN
bool
default n
hex
default 0x4000
-config DEBUG
- bool
- default n
-
-config USE_PRINTK_IN_CAR
- bool
- default n
-
-config USE_OPTION_TABLE
- bool
- default n
-
config MAX_CPUS
int
default 1
bool
default n
-config ATI_RAGE_XL
+source src/console/Kconfig
+
+# This should default to N and be set by SuperI/O drivers that have an UART
+config HAVE_UART_IO_MAPPED
bool
+ default y
-source src/console/Kconfig
+config HAVE_UART_MEMORY_MAPPED
+ bool
+ default n
config HAVE_ACPI_RESUME
bool
default n
+config HAVE_ACPI_SLIC
+ bool
+ default n
+
config ACPI_SSDTX_NUM
int
default 0
bool
default n
+config USE_OPTION_TABLE
+ bool
+ default n
+
config HAVE_OPTION_TABLE
bool
- default y
+ default n
help
This variable specifies whether a given board has a cmos.layout
file containing NVRAM/CMOS bit definitions.
- It defaults to 'y' but can be changed to 'n' in mainboard/*/Kconfig.
+ It defaults to 'n' but can be selected in mainboard/*/Kconfig.
config PIRQ_ROUTE
bool
#
# endmenu
-#TODO Remove this option or make it useful.
-config HAVE_LOW_TABLES
- bool
- default y
- help
- This Option is unused in the code. Since two boards try to set it to
- 'n', they may be broken. We either need to make the option useful or
- get rid of it. The broken boards are:
- asus/m2v-mx_se
- supermicro/h8dme
-
-config HAVE_HIGH_TABLES
- bool
- default y
- help
- This variable specifies whether a given northbridge has high table
- support.
- It is set in northbridge/*/Kconfig.
- Whether or not the high tables are actually written by coreboot is
- configurable by the user via WRITE_HIGH_TABLES.
-
config HAVE_ACPI_TABLES
bool
help
bool
default HAVE_PIRQ_TABLE
-config WRITE_HIGH_TABLES
- bool
- default HAVE_HIGH_TABLES
-
menu "System tables"
config WRITE_HIGH_TABLES
bool "Write 'high' tables to avoid being overwritten in F segment"
- depends on HAVE_HIGH_TABLES
default y
config MULTIBOOT
choice
prompt "Add a payload"
- default PAYLOAD_NONE
+ default PAYLOAD_NONE if !ARCH_X86
+ default PAYLOAD_SEABIOS if ARCH_X86
config PAYLOAD_NONE
bool "None"
You will be able to specify the location and file name of the
payload image later.
+config PAYLOAD_SEABIOS
+ bool "SeaBIOS"
+ depends on ARCH_X86
+ help
+ Select this option if you want to build a coreboot image
+ with a SeaBIOS payload. If you don't know what this is
+ about, just leave it enabled.
+
+ See http://coreboot.org/Payloads for more information.
+
+config PAYLOAD_FILO
+ bool "FILO"
+ help
+ Select this option if you want to build a coreboot image
+ with a FILO payload. If you don't know what this is
+ about, just leave it enabled.
+
+ See http://coreboot.org/Payloads for more information.
+
+endchoice
+
+choice
+ prompt "SeaBIOS version"
+ default SEABIOS_STABLE
+ depends on PAYLOAD_SEABIOS
+
+config SEABIOS_STABLE
+ bool "stable"
+ help
+ Stable SeaBIOS version
+config SEABIOS_MASTER
+ bool "master"
+ help
+ Newest SeaBIOS version
endchoice
-config FALLBACK_PAYLOAD_FILE
+choice
+ prompt "FILO version"
+ default FILO_STABLE
+ depends on PAYLOAD_FILO
+
+config FILO_STABLE
+ bool "0.6.0"
+ help
+ Stable FILO version
+config FILO_MASTER
+ bool "HEAD"
+ help
+ Newest FILO version
+endchoice
+
+config PAYLOAD_FILE
string "Payload path and filename"
depends on PAYLOAD_ELF
default "payload.elf"
help
The path and filename of the ELF executable file to use as payload.
+config PAYLOAD_FILE
+ depends on PAYLOAD_SEABIOS
+ default "payloads/external/SeaBIOS/seabios/out/bios.bin.elf"
+
+config PAYLOAD_FILE
+ depends on PAYLOAD_FILO
+ default "payloads/external/FILO/filo/build/filo.elf"
+
# TODO: Defined if no payload? Breaks build?
config COMPRESSED_PAYLOAD_LZMA
bool "Use LZMA compression for payloads"
default y
- depends on PAYLOAD_ELF
+ depends on PAYLOAD_ELF || PAYLOAD_SEABIOS || PAYLOAD_FILO
help
In order to reduce the size payloads take up in the ROM chip
coreboot can compress them using the LZMA algorithm.
You will be able to specify the location and file name of the
image later.
-config FALLBACK_VGA_BIOS_FILE
+config VGA_BIOS_FILE
string "VGA BIOS path and filename"
depends on VGA_BIOS
default "vgabios.bin"
help
The path and filename of the file to use as VGA BIOS.
-config FALLBACK_VGA_BIOS_ID
+config VGA_BIOS_ID
string "VGA device PCI IDs"
depends on VGA_BIOS
default "1106,3230"
You will be able to specify the location and file name of the
image later.
-config FALLBACK_MBI_FILE
+config MBI_FILE
string "Intel MBI path and filename"
depends on INTEL_MBI
default "mbi.bin"
This option shows a graphical bootsplash screen. The grapics are
loaded from the CBFS file bootsplash.jpg.
-config FALLBACK_BOOTSPLASH_FILE
+config BOOTSPLASH_FILE
string "Bootsplash path and filename"
depends on BOOTSPLASH
default "bootsplash.jpg"
help
- The path and filename of the file to use as graphical bootsplash
- screen. The file format has to be jpg.
+ The path and filename of the file to use as graphical bootsplash
+ screen. The file format has to be jpg.
# TODO: Turn this into a "choice".
config FRAMEBUFFER_VESA_MODE
default y
help
If enabled, you will be able to set breakpoints for gdb debugging.
- See src/arch/i386/lib/c_start.S for details.
+ See src/arch/x86/lib/c_start.S for details.
+
+config HAVE_DEBUG_RAM_SETUP
+ def_bool n
config DEBUG_RAM_SETUP
bool "Output verbose RAM init debug messages"
default n
- depends on (NORTHBRIDGE_AMD_AMDFAM10 \
- || NORTHBRIDGE_AMD_AMDK8 \
- || NORTHBRIDGE_VIA_CN700 \
- || NORTHBRIDGE_VIA_CX700 \
- || NORTHBRIDGE_VIA_VX800 \
- || NORTHBRIDGE_INTEL_E7501 \
- || NORTHBRIDGE_INTEL_I440BX \
- || NORTHBRIDGE_INTEL_I82810 \
- || NORTHBRIDGE_INTEL_I82830 \
- || NORTHBRIDGE_INTEL_I945)
+ depends on HAVE_DEBUG_RAM_SETUP
help
This option enables additional RAM init related debug messages.
It is recommended to enable this when debugging issues on your
If unsure, say N.
+config HAVE_DEBUG_CAR
+ def_bool n
+
+config DEBUG_CAR
+ def_bool n
+ depends on HAVE_DEBUG_CAR
+
+if DEFAULT_CONSOLE_LOGLEVEL_7 || DEFAULT_CONSOLE_LOGLEVEL_8
+# Only visible if debug level is DEBUG (7) or SPEW (8) as it does additional
+# printk(BIOS_DEBUG, ...) calls.
+config DEBUG_CAR
+ bool "Output verbose Cache-as-RAM debug messages"
+ default n
+ depends on HAVE_DEBUG_CAR
+ help
+ This option enables additional CAR related debug messages.
+endif
+
+config DEBUG_PIRQ
+ bool "Check PIRQ table consistency"
+ default n
+ depends on GENERATE_PIRQ_TABLE
+ help
+ If unsure, say N.
+
+config HAVE_DEBUG_SMBUS
+ def_bool n
+
config DEBUG_SMBUS
bool "Output verbose SMBus debug messages"
default n
- depends on (SOUTHBRIDGE_VIA_VT8237R \
- || NORTHBRIDGE_VIA_VX800 \
- || NORTHBRIDGE_VIA_CX700 \
- || NORTHBRIDGE_AMD_AMDK8 \
- || NORTHBRIDGE_AMD_AMDFAM10 \
- || SOUTHBRIDGE_VIA_VT8231)
+ depends on HAVE_DEBUG_SMBUS
help
This option enables additional SMBus (and SPD) debug messages.
If unsure, say N.
+config DEBUG_SMM_RELOCATION
+ bool "Debug SMM relocation code"
+ default n
+ depends on HAVE_SMI_HANDLER
+ help
+ This option enables additional SMM handler relocation related
+ debug messages.
+
+ Note: This option will increase the size of the coreboot image.
+
+ If unsure, say N.
+
+config DEBUG_MALLOC
+ def_bool n
+
+# Only visible if debug level is DEBUG (7) or SPEW (8) as it does additional
+# printk(BIOS_DEBUG, ...) calls.
+if DEFAULT_CONSOLE_LOGLEVEL_7 || DEFAULT_CONSOLE_LOGLEVEL_8
+config DEBUG_MALLOC
+ bool "Output verbose malloc debug messages"
+ default n
+ help
+ This option enables additional malloc related debug messages.
+
+ Note: This option will increase the size of the coreboot image.
+
+ If unsure, say N.
+endif
+
+config REALMODE_DEBUG
+ def_bool n
+ depends on PCI_OPTION_ROM_RUN_REALMODE
+
+if DEFAULT_CONSOLE_LOGLEVEL_7 || DEFAULT_CONSOLE_LOGLEVEL_8
+# Only visible if debug level is DEBUG (7) or SPEW (8) as it does additional
+# printk(BIOS_DEBUG, ...) calls.
+config REALMODE_DEBUG
+ bool "Enable debug messages for option ROM execution"
+ default n
+ depends on PCI_OPTION_ROM_RUN_REALMODE
+ help
+ This option enables additional x86emu related debug messages.
+
+ Note: This option will increase the time to emulate a ROM.
+
+ If unsure, say N.
+endif
+
config X86EMU_DEBUG
bool "Output verbose x86emu debug messages"
default n
depends on X86EMU_DEBUG
help
Print _all_ opcodes that are executed by x86emu.
-
+
WARNING: This will produce a LOT of output and take a long time.
Note: This option will increase the size of the coreboot image.
help
If enabled, you will have a low level shell to examine your machine.
Put llshell() in your (romstage) code to start the shell.
- See src/arch/i386/llshell/llshell.inc for details.
+ See src/arch/x86/llshell/llshell.inc for details.
endmenu
bool
default n
+config RAMINIT_SYSINFO
+ bool
+ default n
+
config ENABLE_APIC_EXT_ID
bool
default n
config WARNINGS_ARE_ERRORS
bool
- default n
+ default y
config ID_SECTION_OFFSET
hex
default 0x10
+# The four POWER_BUTTON_DEFAULT_ENABLE, POWER_BUTTON_DEFAULT_DISABLE,
+# POWER_BUTTON_FORCE_ENABLE and POWER_BUTTON_FORCE_DISABLE options are
+# mutually exclusive. One of these options must be selected in the
+# mainboard Kconfig if the chipset supports enabling and disabling of
+# the power button. Chipset code uses the ENABLE_POWER_BUTTON option set
+# in mainboard/Kconfig to know if the button should be enabled or not.
+
+config POWER_BUTTON_DEFAULT_ENABLE
+ def_bool n
+ help
+ Select when the board has a power button which can optionally be
+ disabled by the user.
+
+config POWER_BUTTON_DEFAULT_DISABLE
+ def_bool n
+ help
+ Select when the board has a power button which can optionally be
+ enabled by the user, e.g. when the board ships with a jumper over
+ the power switch contacts.
+
+config POWER_BUTTON_FORCE_ENABLE
+ def_bool n
+ help
+ Select when the board requires that the power button is always
+ enabled.
+
+config POWER_BUTTON_FORCE_DISABLE
+ def_bool n
+ help
+ Select when the board requires that the power button is always
+ disabled, e.g. when it has been hardwired to ground.
+
+config POWER_BUTTON_IS_OPTIONAL
+ bool
+ default y if POWER_BUTTON_DEFAULT_ENABLE || POWER_BUTTON_DEFAULT_DISABLE
+ default n if !(POWER_BUTTON_DEFAULT_ENABLE || POWER_BUTTON_DEFAULT_DISABLE)
+ help
+ Internal option that controls ENABLE_POWER_BUTTON visibility.
+
source src/Kconfig.deprecated_options