/* * This file is part of the coreboot project. * * Copyright (C) 2007 Uwe Hermann * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation; either version 2 of the License, or * (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA */ #include #include #include #include "i440bx.h" /*----------------------------------------------------------------------------- Macros and definitions. -----------------------------------------------------------------------------*/ /* Uncomment this to enable debugging output. */ #define DEBUG_RAM_SETUP 1 /* Debugging macros. */ #if defined(DEBUG_RAM_SETUP) #define PRINT_DEBUG(x) print_debug(x) #define PRINT_DEBUG_HEX8(x) print_debug_hex8(x) #define PRINT_DEBUG_HEX16(x) print_debug_hex16(x) #define PRINT_DEBUG_HEX32(x) print_debug_hex32(x) #define DUMPNORTH() dump_pci_device(PCI_DEV(0, 0, 0)) #else #define PRINT_DEBUG(x) #define PRINT_DEBUG_HEX8(x) #define PRINT_DEBUG_HEX16(x) #define PRINT_DEBUG_HEX32(x) #define DUMPNORTH() #endif /* SDRAMC[7:5] - SDRAM Mode Select (SMS). */ #define RAM_COMMAND_NORMAL 0x0 #define RAM_COMMAND_NOP 0x1 #define RAM_COMMAND_PRECHARGE 0x2 #define RAM_COMMAND_MRS 0x3 #define RAM_COMMAND_CBR 0x4 /* Map the JEDEC SPD refresh rates (array index) to 440BX refresh rates as * defined in DRAMC[2:0]. * * [0] == Normal 15.625 us -> 15.6 us * [1] == Reduced(.25X) 3.9 us -> 7.8 ns * [2] == Reduced(.5X) 7.8 us -> 7.8 us * [3] == Extended(2x) 31.3 us -> 31.2 us * [4] == Extended(4x) 62.5 us -> 62.4 us * [5] == Extended(8x) 125 us -> 124.8 us */ static const uint32_t refresh_rate_map[] = { 1, 5, 5, 2, 3, 4 }; /* Table format: register, bitmask, value. */ static const long register_values[] = { /* NBXCFG - NBX Configuration Register * 0x50 - 0x53 * * [31:24] SDRAM Row Without ECC * 0 = ECC components are populated in this row * 1 = ECC components are not populated in this row * [23:19] Reserved * [18:18] Host Bus Fast Data Ready Enable (HBFDRE) * Assertion of DRAM data on host bus occurs... * 0 = ...one clock after sampling snoop results (default) * 1 = ...on the same clock the snoop result is being sampled * (this mode is faster by one clock cycle) * [17:17] ECC - EDO static Drive mode * 0 = Normal mode (default) * 1 = ECC signals are always driven * [16:16] IDSEL_REDIRECT * 0 = IDSEL1 is allocated to this bridge (default) * 1 = IDSEL7 is allocated to this bridge * [15:15] WSC# Handshake Disable * 1 = Uni-processor mode * 0 = Dual-processor mode with external IOAPIC (default) * [14:14] Intel Reserved * [13:12] Host/DRAM Frequency * 00 = 100 MHz * 01 = Reserved * 10 = 66 MHz * 11 = Reserved * [11:11] AGP to PCI Access Enable * 1 = Enable * 0 = Disable * [10:10] PCI Agent to Aperture Access Disable * 1 = Disable * 0 = Enable (default) * [09:09] Aperture Access Global Enable * 1 = Enable * 0 = Disable * [08:07] DRAM Data Integrity Mode (DDIM) * 00 = Non-ECC * 01 = EC-only * 10 = ECC Mode * 11 = ECC Mode with hardware scrubbing enabled * [06:06] ECC Diagnostic Mode Enable (EDME) * 1 = Enable * 0 = Normal operation mode (default) * [05:05] MDA Present (MDAP) * Works in conjunction with the VGA_EN bit. * VGA_EN MDAP * 0 x All VGA cycles are sent to PCI * 1 0 All VGA cycles are sent to AGP * 1 1 All VGA cycles are sent to AGP, except for * cycles in the MDA range. * [04:04] Reserved * [03:03] USWC Write Post During I/O Bridge Access Enable (UWPIO) * 1 = Enable * 0 = Disable * [02:02] In-Order Queue Depth (IOQD) * 1 = In-order queue = maximum * 0 = A7# is sampled asserted (i.e., 0) * [01:00] Reserved */ // TODO NBXCFG + 0, 0x00, 0x0c, // NBXCFG + 1, 0x00, 0xa0, NBXCFG + 1, 0x00, 0x80, NBXCFG + 2, 0x00, 0x00, NBXCFG + 3, 0x00, 0xff, /* DRAMC - DRAM Control Register * 0x57 * * [7:6] Reserved * [5:5] Module Mode Configuration (MMCONFIG) * TODO * [4:3] DRAM Type (DT) * 00 = EDO * 01 = SDRAM * 10 = Registered SDRAM * 11 = Reserved * Note: EDO, SDRAM and Registered SDRAM cannot be mixed. * [2:0] DRAM Refresh Rate (DRR) * 000 = Refresh disabled * 001 = 15.6 us * 010 = 31.2 us * 011 = 62.4 us * 100 = 124.8 us * 101 = 249.6 us * 110 = Reserved * 111 = Reserved */ /* Choose SDRAM (not registered), and disable refresh for now. */ DRAMC, 0x00, 0x08, /* * PAM[6:0] - Programmable Attribute Map Registers * 0x59 - 0x5f * * 0x59 [3:0] Reserved * 0x59 [5:4] 0xF0000 - 0xFFFFF BIOS area * 0x5a [1:0] 0xC0000 - 0xC3FFF ISA add-on BIOS * 0x5a [5:4] 0xC4000 - 0xC7FFF ISA add-on BIOS * 0x5b [1:0] 0xC8000 - 0xCBFFF ISA add-on BIOS * 0x5b [5:4] 0xCC000 - 0xCFFFF ISA add-on BIOS * 0x5c [1:0] 0xD0000 - 0xD3FFF ISA add-on BIOS * 0x5c [5:4] 0xD4000 - 0xD7FFF ISA add-on BIOS * 0x5d [1:0] 0xD8000 - 0xDBFFF ISA add-on BIOS * 0x5d [5:4] 0xDC000 - 0xDFFFF ISA add-on BIOS * 0x5e [1:0] 0xE0000 - 0xE3FFF BIOS entension * 0x5e [5:4] 0xE4000 - 0xE7FFF BIOS entension * 0x5f [1:0] 0xE8000 - 0xEBFFF BIOS entension * 0x5f [5:4] 0xEC000 - 0xEFFFF BIOS entension * * Bit assignment: * 00 = DRAM Disabled (all access goes to memory mapped I/O space) * 01 = Read Only (Reads to DRAM, writes to memory mapped I/O space) * 10 = Write Only (Writes to DRAM, reads to memory mapped I/O space) * 11 = Read/Write (all access goes to DRAM) */ // TODO PAM0, 0x00, 0x00, PAM1, 0x00, 0x00, PAM2, 0x00, 0x00, PAM3, 0x00, 0x00, PAM4, 0x00, 0x00, PAM5, 0x00, 0x00, PAM6, 0x00, 0x00, /* DRB[0:7] - DRAM Row Boundary Registers * 0x60 - 0x67 * * An array of 8 byte registers, which hold the ending memory address * assigned to each pair of DIMMs, in 8MB granularity. * * 0x60 DRB0 = Total memory in row0 (in 8 MB) * 0x61 DRB1 = Total memory in row0+1 (in 8 MB) * 0x62 DRB2 = Total memory in row0+1+2 (in 8 MB) * 0x63 DRB3 = Total memory in row0+1+2+3 (in 8 MB) * 0x64 DRB4 = Total memory in row0+1+2+3+4 (in 8 MB) * 0x65 DRB5 = Total memory in row0+1+2+3+4+5 (in 8 MB) * 0x66 DRB6 = Total memory in row0+1+2+3+4+5+6 (in 8 MB) * 0x67 DRB7 = Total memory in row0+1+2+3+4+5+6+7 (in 8 MB) */ /* Set the DRBs to zero for now, this will be fixed later. */ DRB0, 0x00, 0x00, DRB1, 0x00, 0x00, DRB2, 0x00, 0x00, DRB3, 0x00, 0x00, DRB4, 0x00, 0x00, DRB5, 0x00, 0x00, DRB6, 0x00, 0x00, DRB7, 0x00, 0x00, /* FDHC - Fixed DRAM Hole Control Register * 0x68 * * Controls two fixed DRAM holes: 512 KB - 640 KB and 15 MB - 16 MB. * * [7:6] Hole Enable (HEN) * 00 = None * 01 = 512 KB - 640 KB (128 KB) * 10 = 15 MB - 16 MB (1 MB) * 11 = Reserved * [5:0] Reserved */ /* No memory holes. */ FDHC, 0x00, 0x00, /* RPS - SDRAM Row Page Size Register * 0x74 - 0x75 * * Sets the row page size for SDRAM. For EDO memory, the page * size is fixed at 2 KB. * * [15:0] Page Size (PS) * TODO */ // TODO RPS + 0, 0x00, 0x00, RPS + 1, 0x00, 0x00, /* SDRAMC - SDRAM Control Register * 0x76 - 0x77 * * [15:10] Reserved * [09:08] Idle/Pipeline DRAM Leadoff Timing (IPDLT) * 00 = Illegal * 01 = Add a clock delay to the lead-off clock count * 10 = Illegal * 11 = Illegal * [07:05] SDRAM Mode Select (SMS) * 000 = Normal SDRAM Operation (default) * 001 = NOP Command Enable * 010 = All Banks Precharge Enable * 011 = Mode Register Set Enable * 100 = CBR Enable * 101 = Reserved * 110 = Reserved * 111 = Reserved * [04:04] SDRAMPWR * 0 = 3 DIMM configuration * 1 = 4 DIMM configuration * [03:03] Leadoff Command Timing (LCT) * 0 = 4 CS# Clock * 1 = 3 CS# Clock * [02:02] CAS# Latency (CL) * 0 = 3 DCLK CAS# latency * 1 = 2 DCLK CAS# latency * [01:01] SDRAM RAS# to CAS# Delay (SRCD) * 0 = 3 clocks between a row activate and a read or write cmd. * 1 = 2 clocks between a row activate and a read or write cmd. * [00:00] SDRAM RAS# Precharge (SRP) * 0 = 3 clocks of RAS# precharge * 1 = 2 clocks of RAS# precharge */ SDRAMC + 0, 0x00, 0x00, SDRAMC + 1, 0x00, 0x00, /* PGPOL - Paging Policy Register * 0x78 - 0x79 * * [15:08] Banks per Row (BPR) * TODO * 0 = 2 banks * 1 = 4 banks * [07:05] Reserved * [04:04] Intel Reserved * [03:00] DRAM Idle Timer (DIT) * 0000 = 0 clocks * 0001 = 2 clocks * 0010 = 4 clocks * 0011 = 8 clocks * 0100 = 10 clocks * 0101 = 12 clocks * 0110 = 16 clocks * 0111 = 32 clocks * 1xxx = Infinite (pages are not closed for idle condition) */ // TODO PGPOL + 0, 0x00, 0x00, PGPOL + 1, 0x00, 0xff, /* PMCR - Power Management Control Register * 0x7a * * [07:07] Power Down SDRAM Enable (PDSE) * 1 = Enable * 0 = Disable * [06:06] ACPI Control Register Enable (SCRE) * 1 = Enable * 0 = Disable (default) * [05:05] Suspend Refresh Type (SRT) * 1 = Self refresh mode * 0 = CBR fresh mode * [04:04] Normal Refresh Enable (NREF_EN) * 1 = Enable * 0 = Disable * [03:03] Quick Start Mode (QSTART) * 1 = Quick start mode for the processor is enabled * [02:02] Gated Clock Enable (GCLKEN) * 1 = Enable * 0 = Disable * [01:01] AGP Disable (AGP_DIS) * 1 = Disable * 0 = Enable * [00:00] CPU reset without PCIRST enable (CRst_En) * 1 = Enable * 0 = Disable */ /* Enable normal refresh and the gated clock. */ // TODO: Only do this later? // PMCR, 0x00, 0x14, // PMCR, 0x00, 0x10, PMCR, 0x00, 0x00, }; /*----------------------------------------------------------------------------- SDRAM configuration functions. -----------------------------------------------------------------------------*/ /** * Send the specified RAM command to all DIMMs. * * @param Memory controller * @param TODO * @param TODO */ static void do_ram_command(const struct mem_controller *ctrl, uint32_t command, uint32_t addr_offset) { int i; uint16_t reg; /* TODO: Support for multiple DIMMs. */ /* Configure the RAM command. */ reg = pci_read_config16(ctrl->d0, SDRAMC); reg &= 0xff1f; /* Clear bits 7-5. */ reg |= (uint16_t) (command << 5); pci_write_config16(ctrl->d0, SDRAMC, reg); /* RAM_COMMAND_NORMAL affects only the memory controller and doesn't need to be "sent" to the DIMMs. */ /* if (command == RAM_COMMAND_NORMAL) return; */ PRINT_DEBUG(" Sending RAM command 0x"); PRINT_DEBUG_HEX16(reg); PRINT_DEBUG(" to 0x"); PRINT_DEBUG_HEX32(0 + addr_offset); // FIXME PRINT_DEBUG("\r\n"); /* Read from (DIMM start address + addr_offset). */ read32(0 + addr_offset); // FIXME } /*----------------------------------------------------------------------------- DIMM-independant configuration functions. -----------------------------------------------------------------------------*/ /** * TODO. * * @param Memory controller */ static void spd_enable_refresh(const struct mem_controller *ctrl) { int i, value; uint8_t reg; reg = pci_read_config8(ctrl->d0, DRAMC); for (i = 0; i < DIMM_SOCKETS; i++) { value = spd_read_byte(ctrl->channel0[i], SPD_REFRESH); if (value < 0) continue; reg = (reg & 0xf8) | refresh_rate_map[(value & 0x7f)]; PRINT_DEBUG(" Enabling refresh (DRAMC = 0x"); PRINT_DEBUG_HEX8(reg); PRINT_DEBUG(") for DIMM "); PRINT_DEBUG_HEX8(i); PRINT_DEBUG("\r\n"); } pci_write_config8(ctrl->d0, DRAMC, reg); } /*----------------------------------------------------------------------------- Public interface. -----------------------------------------------------------------------------*/ /** * TODO. * * @param Memory controller */ static void sdram_set_registers(const struct mem_controller *ctrl) { int i, max; uint8_t reg; PRINT_DEBUG("Northbridge prior to SDRAM init:\r\n"); DUMPNORTH(); max = sizeof(register_values) / sizeof(register_values[0]); /* Set registers as specified in the register_values[] array. */ for (i = 0; i < max; i += 3) { reg = pci_read_config8(ctrl->d0, register_values[i]); reg &= register_values[i + 1]; reg |= register_values[i + 2] & ~(register_values[i + 1]); pci_write_config8(ctrl->d0, register_values[i], reg); PRINT_DEBUG(" Set register 0x"); PRINT_DEBUG_HEX8(register_values[i]); PRINT_DEBUG(" to 0x"); PRINT_DEBUG_HEX8(reg); PRINT_DEBUG("\r\n"); } } /** * TODO. * * @param Memory controller */ static void sdram_set_spd_registers(const struct mem_controller *ctrl) { /* TODO: Don't hardcode the values here, get info via SPD. */ /* Map all legacy regions to RAM (read/write). This is required if * you want to use the RAM area from 768 KB - 1 MB. If the PAM * registers are not set here appropriately, the RAM in that region * will not be accessible, thus a RAM check of it will also fail. */ pci_write_config8(ctrl->d0, PAM0, 0x30); pci_write_config8(ctrl->d0, PAM1, 0x33); pci_write_config8(ctrl->d0, PAM2, 0x33); pci_write_config8(ctrl->d0, PAM3, 0x33); pci_write_config8(ctrl->d0, PAM4, 0x33); pci_write_config8(ctrl->d0, PAM5, 0x33); pci_write_config8(ctrl->d0, PAM6, 0x33); /* TODO: Set DRB0-DRB7. */ /* Currently this is hardcoded to one 64 MB DIMM in slot 0. */ pci_write_config8(ctrl->d0, DRB0, 0x08); pci_write_config8(ctrl->d0, DRB1, 0x08); pci_write_config8(ctrl->d0, DRB2, 0x08); pci_write_config8(ctrl->d0, DRB3, 0x08); pci_write_config8(ctrl->d0, DRB4, 0x08); pci_write_config8(ctrl->d0, DRB5, 0x08); pci_write_config8(ctrl->d0, DRB6, 0x08); pci_write_config8(ctrl->d0, DRB7, 0x08); /* TODO: Set DRAMC. Don't enable refresh for now. */ pci_write_config8(ctrl->d0, DRAMC, 0x08); /* TODO: Set RPS. */ pci_write_config16(ctrl->d0, RPS, 0x0001); /* TODO: Set SDRAMC. */ // pci_write_config16(ctrl->d0, SDRAMC, 0x010f); // FIXME? pci_write_config16(ctrl->d0, SDRAMC, 0x0003); // FIXME? /* TODO: Set PGPOL. */ // pci_write_config16(ctrl->d0, PGPOL, 0x0107); pci_write_config16(ctrl->d0, PGPOL, 0x0123); /* TODO: Set NBXCFG. */ // pci_write_config32(ctrl->d0, NBXCFG, 0x0100220c); // FIXME? pci_write_config32(ctrl->d0, NBXCFG, 0xff00800c); /* TODO: Set PMCR? */ // pci_write_config8(ctrl->d0, PMCR, 0x14); pci_write_config8(ctrl->d0, PMCR, 0x10); /* TODO? */ pci_write_config8(ctrl->d0, PCI_LATENCY_TIMER, 0x40); pci_write_config8(ctrl->d0, DRAMT, 0x03); pci_write_config8(ctrl->d0, MBSC, 0x03); pci_write_config8(ctrl->d0, SCRR, 0x38); } /** * Enable SDRAM. * * @param Number of controllers * @param Memory controller */ static void sdram_enable(int controllers, const struct mem_controller *ctrl) { int i; /* 0. Wait until power/voltages and clocks are stable (200us). */ udelay(200); /* 1. Apply NOP. Wait 200 clock cycles (200us should do). */ PRINT_DEBUG("RAM Enable 1: Apply NOP\r\n"); do_ram_command(ctrl, RAM_COMMAND_NOP, 0); udelay(200); /* 2. Precharge all. Wait tRP. */ PRINT_DEBUG("RAM Enable 2: Precharge all\r\n"); do_ram_command(ctrl, RAM_COMMAND_PRECHARGE, 0); udelay(1); /* 3. Perform 8 refresh cycles. Wait tRC each time. */ PRINT_DEBUG("RAM Enable 3: CBR\r\n"); for (i = 0; i < 8; i++) { do_ram_command(ctrl, RAM_COMMAND_CBR, 0); udelay(1); } /* 4. Mode register set. Wait two memory cycles. */ PRINT_DEBUG("RAM Enable 4: Mode register set\r\n"); do_ram_command(ctrl, RAM_COMMAND_MRS, 0x1d0); udelay(2); /* 5. Normal operation. */ PRINT_DEBUG("RAM Enable 5: Normal operation\r\n"); do_ram_command(ctrl, RAM_COMMAND_NORMAL, 0); udelay(1); /* 6. Finally enable refresh. */ PRINT_DEBUG("RAM Enable 6: Enable refresh\r\n"); // pci_write_config8(ctrl->d0, PMCR, 0x10); spd_enable_refresh(ctrl); udelay(1); PRINT_DEBUG("Northbridge following SDRAM init:\r\n"); DUMPNORTH(); }