## ## This file is part of the coreboot project. ## ## Copyright (C) 2006 AMD ## Written by Yinghai Lu for AMD. ## ## Copyright (C) 2006 MSI ## Written by bxshi for MSI. ## ## This program is free software; you can redistribute it and/or modify ## it under the terms of the GNU General Public License as published by ## the Free Software Foundation; either version 2 of the License, or ## (at your option) any later version. ## ## This program is distributed in the hope that it will be useful, ## but WITHOUT ANY WARRANTY; without even the implied warranty of ## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the ## GNU General Public License for more details. ## ## You should have received a copy of the GNU General Public License ## along with this program; if not, write to the Free Software ## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA ## uses HAVE_MP_TABLE uses HAVE_PIRQ_TABLE uses HAVE_ACPI_TABLES uses ACPI_SSDTX_NUM uses USE_FALLBACK_IMAGE uses HAVE_FALLBACK_BOOT uses HAVE_HARD_RESET uses IRQ_SLOT_COUNT uses HAVE_OPTION_TABLE uses CONFIG_MAX_CPUS uses CONFIG_MAX_PHYSICAL_CPUS uses CONFIG_LOGICAL_CPUS uses CONFIG_IOAPIC uses CONFIG_SMP uses FALLBACK_SIZE uses ROM_SIZE uses ROM_SECTION_SIZE uses ROM_IMAGE_SIZE uses ROM_SECTION_SIZE uses ROM_SECTION_OFFSET uses CONFIG_ROM_PAYLOAD uses CONFIG_ROM_PAYLOAD_START uses CONFIG_COMPRESSED_PAYLOAD_LZMA uses CONFIG_PRECOMPRESSED_PAYLOAD uses PAYLOAD_SIZE uses _ROMBASE uses XIP_ROM_SIZE uses XIP_ROM_BASE uses STACK_SIZE uses HEAP_SIZE uses USE_OPTION_TABLE uses LB_CKS_RANGE_START uses LB_CKS_RANGE_END uses LB_CKS_LOC uses MAINBOARD_PART_NUMBER uses MAINBOARD_VENDOR uses MAINBOARD uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID uses COREBOOT_EXTRA_VERSION uses _RAMBASE uses TTYS0_BAUD uses TTYS0_BASE uses TTYS0_LCS uses DEFAULT_CONSOLE_LOGLEVEL uses MAXIMUM_CONSOLE_LOGLEVEL uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL uses CONFIG_CONSOLE_SERIAL8250 uses HAVE_INIT_TIMER uses CONFIG_GDB_STUB uses CONFIG_GDB_STUB uses CROSS_COMPILE uses CC uses HOSTCC uses OBJCOPY uses CONFIG_CHIP_NAME uses CONFIG_CONSOLE_VGA uses CONFIG_PCI_ROM_RUN uses HW_MEM_HOLE_SIZEK uses HW_MEM_HOLE_SIZE_AUTO_INC uses K8_HT_FREQ_1G_SUPPORT uses HT_CHAIN_UNITID_BASE uses HT_CHAIN_END_UNITID_BASE uses SB_HT_CHAIN_ON_BUS0 uses SB_HT_CHAIN_UNITID_OFFSET_ONLY uses USE_DCACHE_RAM uses DCACHE_RAM_BASE uses DCACHE_RAM_SIZE uses DCACHE_RAM_GLOBAL_VAR_SIZE uses CONFIG_USE_INIT uses SERIAL_CPU_INIT uses ENABLE_APIC_EXT_ID uses APIC_ID_OFFSET uses LIFT_BSP_APIC_ID uses CONFIG_PCI_64BIT_PREF_MEM uses CONFIG_LB_MEM_TOPK uses CONFIG_USE_PRINTK_IN_CAR ### ### Build options ### ## ## ROM_SIZE is the size of boot ROM that this board will use. ## default ROM_SIZE=524288 ## ## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use ## #default FALLBACK_SIZE=131072 #256K default FALLBACK_SIZE=0x40000 #more 1M for pgtbl default CONFIG_LB_MEM_TOPK=2048 ## ## Build code for the fallback boot ## default HAVE_FALLBACK_BOOT=1 ## ## Build code to reset the motherboard from coreboot ## default HAVE_HARD_RESET=1 ## ## Build code to export a programmable irq routing table ## default HAVE_PIRQ_TABLE=1 default IRQ_SLOT_COUNT=11 ## ## Build code to export an x86 MP table ## Useful for specifying IRQ routing values ## default HAVE_MP_TABLE=1 ## ACPI tables will be included #default HAVE_ACPI_TABLES=1 ## extra SSDT num #default ACPI_SSDTX_NUM=1 ## ## Build code to export a CMOS option table ## default HAVE_OPTION_TABLE=1 ## ## Move the default coreboot cmos range off of AMD RTC registers ## default LB_CKS_RANGE_START=49 default LB_CKS_RANGE_END=122 default LB_CKS_LOC=123 ## ## Build code for SMP support ## Only worry about 2 micro processors ## default CONFIG_SMP=1 default CONFIG_MAX_CPUS=4 default CONFIG_MAX_PHYSICAL_CPUS=2 default CONFIG_LOGICAL_CPUS=1 default SERIAL_CPU_INIT=0 default ENABLE_APIC_EXT_ID=0 default APIC_ID_OFFSET=0x8 default LIFT_BSP_APIC_ID=1 #CHIP_NAME ? default CONFIG_CHIP_NAME=1 #memory hole size, 0 mean disable, others will enable the hole, at that case if it is small than mmio_basek, it will use mmio_basek instead. #2G #default HW_MEM_HOLE_SIZEK=0x200000 #1G default HW_MEM_HOLE_SIZEK=0x100000 #512M #default HW_MEM_HOLE_SIZEK=0x80000 #make auto increase hole size to avoid hole_startk equal to basek so as to make some kernel happy #default HW_MEM_HOLE_SIZE_AUTO_INC=1 #Opteron K8 1G HT Support default K8_HT_FREQ_1G_SUPPORT=1 #VGA Console default CONFIG_CONSOLE_VGA=1 default CONFIG_PCI_ROM_RUN=1 #HT Unit ID offset, default is 1, the typical one default HT_CHAIN_UNITID_BASE=0x06 #real SB Unit ID, default is 0x20, mean dont touch it at last default HT_CHAIN_END_UNITID_BASE=0x01 #make the SB HT chain on bus 0, default is not (0) default SB_HT_CHAIN_ON_BUS0=2 #only offset for SB chain?, default is yes(1) #default SB_HT_CHAIN_UNITID_OFFSET_ONLY=0 #allow capable device use that above 4G #default CONFIG_PCI_64BIT_PREF_MEM=1 ## ## enable CACHE_AS_RAM specifics ## default USE_DCACHE_RAM=1 default DCACHE_RAM_BASE=0xcc000 default DCACHE_RAM_SIZE=0x04000 default DCACHE_RAM_GLOBAL_VAR_SIZE=0x01000 default CONFIG_USE_INIT=0 ## ## Build code to setup a generic IOAPIC ## default CONFIG_IOAPIC=1 ## ## Clean up the motherboard id strings ## default MAINBOARD_PART_NUMBER="MS9185" default MAINBOARD_VENDOR="MSI" default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x1022 default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2b80 ### ### coreboot layout values ### ## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy. default ROM_IMAGE_SIZE = 65536 ## ## Use a small 8K stack ## default STACK_SIZE=0x2000 ## ## Use a small 32K heap ## default HEAP_SIZE=0x8000 ## ## Only use the option table in a normal image ## default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE ## ## Coreboot C code runs at this location in RAM ## default _RAMBASE=0x00100000 ## ## Load the payload from the ROM ## default CONFIG_ROM_PAYLOAD = 1 ### ### Defaults of options that you may want to override in the target config file ### ## ## The default compiler ## default CC="$(CROSS_COMPILE)gcc -m32" default HOSTCC="gcc" ## ## Disable the gdb stub by default ## default CONFIG_GDB_STUB=0 ## ## The Serial Console ## default CONFIG_USE_PRINTK_IN_CAR=1 # To Enable the Serial Console default CONFIG_CONSOLE_SERIAL8250=1 ## Select the serial console baud rate default TTYS0_BAUD=115200 #default TTYS0_BAUD=57600 #default TTYS0_BAUD=38400 #default TTYS0_BAUD=19200 #default TTYS0_BAUD=9600 #default TTYS0_BAUD=4800 #default TTYS0_BAUD=2400 #default TTYS0_BAUD=1200 # Select the serial console base port default TTYS0_BASE=0x3f8 # Select the serial protocol # This defaults to 8 data bits, 1 stop bit, and no parity default TTYS0_LCS=0x3 ## ### Select the coreboot loglevel ## ## EMERG 1 system is unusable ## ALERT 2 action must be taken immediately ## CRIT 3 critical conditions ## ERR 4 error conditions ## WARNING 5 warning conditions ## NOTICE 6 normal but significant condition ## INFO 7 informational ## DEBUG 8 debug-level messages ## SPEW 9 Way too many details ## Request this level of debugging output default DEFAULT_CONSOLE_LOGLEVEL=8 ## At a maximum only compile in this level of debugging default MAXIMUM_CONSOLE_LOGLEVEL=8 ## ## Select power on after power fail setting default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON" ### End Options.lb end