/* * This file is part of the coreboot project. * * Copyright (C) 2000, 2007 Ronald G. Minnich * Copyright (C) 2005 Eswar Nallusamy, LANL * Copyright (C) 2005 Tyan (written by Yinghai Lu for Tyan) * Copyright (C) 2007-2010 coresystems GmbH * Copyright (C) 2007 Carl-Daniel Hailfinger * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation; version 2 of the License. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA */ #include #include #include #include #define CacheSize CONFIG_DCACHE_RAM_SIZE #define CacheBase (0xd0000 - CacheSize) /* Save the BIST result. */ movl %eax, %ebp CacheAsRam: /* Check whether the processor has HT capability. */ movl $01, %eax cpuid btl $28, %edx jnc NotHtProcessor bswapl %ebx cmpb $01, %bh jbe NotHtProcessor /* * It is a HT processor. Send SIPI to the other logical processor * within this processor so that the CAR related common system * registers are programmed accordingly. */ /* * Use some register that is common to both logical processors * as semaphore. Refer Appendix B, Vol.3. */ xorl %eax, %eax xorl %edx, %edx movl $MTRRfix64K_00000_MSR, %ecx wrmsr /* * Figure out the logical AP's APIC ID; the following logic will * work only for processors with 2 threads. * Refer to Vol 3. Table 7-1 for details about this logic. */ movl $0xFEE00020, %esi movl (%esi), %ebx andl $0xFF000000, %ebx bswapl %ebx btl $0, %ebx jnc LogicalAP0 andb $0xFE, %bl jmp Send_SIPI LogicalAP0: orb $0x01, %bl Send_SIPI: bswapl %ebx /* EBX - logical AP's APIC ID. */ /* * Fill up the IPI command registers in the Local APIC mapped to * default address and issue SIPI to the other logical processor * within this processor die. */ Retry_SIPI: movl %ebx, %eax movl $0xFEE00310, %esi movl %eax, (%esi) /* SIPI vector - F900:0000 */ movl $0x000006F9, %eax movl $0xFEE00300, %esi movl %eax, (%esi) movl $0x30, %ecx SIPI_Delay: pause decl %ecx jnz SIPI_Delay movl (%esi), %eax andl $0x00001000, %eax jnz Retry_SIPI /* Wait for the Logical AP to complete initialization. */ LogicalAP_SIPINotdone: movl $MTRRfix64K_00000_MSR, %ecx rdmsr orl %eax, %eax jz LogicalAP_SIPINotdone NotHtProcessor: /* Set the default memory type and enable fixed and variable MTRRs. */ movl $MTRRdefType_MSR, %ecx xorl %edx, %edx movl $(MTRRdefTypeEn | MTRRdefTypeFixEn), %eax wrmsr /* Clear all MTRRs. */ xorl %edx, %edx movl $all_mtrr_msrs, %esi clear_fixed_var_mtrr: lodsl (%esi), %eax testl %eax, %eax jz clear_fixed_var_mtrr_out movl %eax, %ecx xorl %eax, %eax wrmsr jmp clear_fixed_var_mtrr all_mtrr_msrs: /* fixed MTRR MSRs */ .long MTRRfix64K_00000_MSR .long MTRRfix16K_80000_MSR .long MTRRfix16K_A0000_MSR .long MTRRfix4K_C0000_MSR .long MTRRfix4K_C8000_MSR .long MTRRfix4K_D0000_MSR .long MTRRfix4K_D8000_MSR .long MTRRfix4K_E0000_MSR .long MTRRfix4K_E8000_MSR .long MTRRfix4K_F0000_MSR .long MTRRfix4K_F8000_MSR /* var MTRR MSRs */ .long MTRRphysBase_MSR(0) .long MTRRphysMask_MSR(0) .long MTRRphysBase_MSR(1) .long MTRRphysMask_MSR(1) .long MTRRphysBase_MSR(2) .long MTRRphysMask_MSR(2) .long MTRRphysBase_MSR(3) .long MTRRphysMask_MSR(3) .long MTRRphysBase_MSR(4) .long MTRRphysMask_MSR(4) .long MTRRphysBase_MSR(5) .long MTRRphysMask_MSR(5) .long MTRRphysBase_MSR(6) .long MTRRphysMask_MSR(6) .long MTRRphysBase_MSR(7) .long MTRRphysMask_MSR(7) .long 0x000 /* NULL, end of table */ clear_fixed_var_mtrr_out: /* * 0x06 is the WB IO type for a given 4k segment. * segs is the number of 4k segments in the area of the particular * register we want to use for CAR. * reg is the register where the IO type should be stored. */ .macro extractmask segs, reg .if \segs <= 0 /* * The xorl here is superfluous because at the point of first execution * of this macro, %eax and %edx are cleared. Later invocations of this * macro will have a monotonically increasing segs parameter. */ xorl \reg, \reg .elseif \segs == 1 movl $0x06000000, \reg /* WB IO type */ .elseif \segs == 2 movl $0x06060000, \reg /* WB IO type */ .elseif \segs == 3 movl $0x06060600, \reg /* WB IO type */ .elseif \segs >= 4 movl $0x06060606, \reg /* WB IO type */ .endif .endm /* * carsize is the cache size in bytes we want to use for CAR. * windowoffset is the 32k-aligned window into CAR size. */ .macro simplemask carsize, windowoffset .set gas_bug_workaround,(((\carsize - \windowoffset) / 0x1000) - 4) extractmask gas_bug_workaround, %eax .set gas_bug_workaround,(((\carsize - \windowoffset) / 0x1000)) extractmask gas_bug_workaround, %edx /* * Without the gas bug workaround, the entire macro would consist * only of the two lines below: * extractmask (((\carsize - \windowoffset) / 0x1000) - 4), %eax * extractmask (((\carsize - \windowoffset) / 0x1000)), %edx */ .endm #if CacheSize > 0x10000 #error Invalid CAR size, must be at most 64k. #endif #if CacheSize < 0x1000 #error Invalid CAR size, must be at least 4k. This is a processor limitation. #endif #if (CacheSize & (0x1000 - 1)) #error Invalid CAR size, is not a multiple of 4k. This is a processor limitation. #endif #if CacheSize > 0x8000 /* Enable caching for 32K-64K using fixed MTRR. */ movl $MTRRfix4K_C0000_MSR, %ecx simplemask CacheSize, 0x8000 wrmsr #endif /* Enable caching for 0-32K using fixed MTRR. */ movl $MTRRfix4K_C8000_MSR, %ecx simplemask CacheSize, 0 wrmsr #if defined(CONFIG_XIP_ROM_SIZE) && defined(CONFIG_XIP_ROM_BASE) /* * Enable write base caching so we can do execute in place (XIP) * on the flash ROM. */ movl $MTRRphysBase_MSR(1), %ecx xorl %edx, %edx /* * IMPORTANT: The following calculation _must_ be done at runtime. See * http://www.coreboot.org/pipermail/coreboot/2010-October/060855.html */ movl $copy_and_run, %eax andl $(~(CONFIG_XIP_ROM_SIZE - 1)), %eax orl $MTRR_TYPE_WRBACK, %eax wrmsr movl $MTRRphysMask_MSR(1), %ecx movl $0x0000000f, %edx movl $(~(CONFIG_XIP_ROM_SIZE - 1) | MTRRphysMaskValid), %eax wrmsr #endif /* CONFIG_XIP_ROM_SIZE && CONFIG_XIP_ROM_BASE */ /* Enable cache. */ movl %cr0, %eax andl $(~((1 << 30) | (1 << 29))), %eax movl %eax, %cr0 /* Read the range with lodsl. */ movl $CacheBase, %esi cld movl $(CacheSize >> 2), %ecx rep lodsl /* Clear the range. */ movl $CacheBase, %edi movl $(CacheSize >> 2), %ecx xorl %eax, %eax rep stosl #if 0 /* Check the cache as ram. */ movl $CacheBase, %esi movl $(CacheSize >> 2), %ecx .xin1: movl %esi, %eax movl %eax, (%esi) decl %ecx je .xout1 add $4, %esi jmp .xin1 .xout1: movl $CacheBase, %esi // movl $(CacheSize >> 2), %ecx movl $4, %ecx .xin1x: movl %esi, %eax movl $0x4000, %edx movb %ah, %al .testx1: outb %al, $0x80 decl %edx jnz .testx1 movl (%esi), %eax cmpb 0xff, %al je .xin2 /* Don't show. */ movl $0x4000, %edx .testx2: outb %al, $0x80 decl %edx jnz .testx2 .xin2: decl %ecx je .xout1x add $4, %esi jmp .xin1x .xout1x: #endif movl $(CacheBase + CacheSize - 4), %eax movl %eax, %esp lout: /* Restore the BIST result. */ movl %ebp, %eax /* We need to set EBP? No need. */ movl %esp, %ebp pushl %eax /* BIST */ call main /* We don't need CAR from now on. */ /* Disable cache. */ movl %cr0, %eax orl $(1 << 30), %eax movl %eax, %cr0 /* Clear sth. */ movl $MTRRfix4K_C8000_MSR, %ecx xorl %edx, %edx xorl %eax, %eax wrmsr #if CONFIG_DCACHE_RAM_SIZE > 0x8000 movl $MTRRfix4K_C0000_MSR, %ecx wrmsr #endif /* * Set the default memory type and disable fixed * and enable variable MTRRs. */ movl $MTRRdefType_MSR, %ecx xorl %edx, %edx movl $MTRRdefTypeEn, %eax /* Enable variable and disable fixed MTRRs. */ wrmsr /* Enable cache. */ movl %cr0, %eax andl $(~((1 << 30) | (1 << 29))), %eax movl %eax, %cr0 /* Clear boot_complete flag. */ xorl %ebp, %ebp __main: post_code(POST_PREPARE_RAMSTAGE) cld /* Clear direction flag. */ movl %ebp, %esi movl $ROMSTAGE_STACK, %esp movl %esp, %ebp pushl %esi call copy_and_run .Lhlt: post_code(POST_DEAD_CODE) hlt jmp .Lhlt