3 uses USE_FALLBACK_IMAGE
4 uses HAVE_FALLBACK_BOOT
8 uses HARD_RESET_FUNCTION
10 uses HAVE_OPTION_TABLE
12 uses CONFIG_MAX_PHYSICAL_CPUS
13 uses CONFIG_LOGICAL_CPUS
21 uses ROM_SECTION_OFFSET
22 uses CONFIG_ROM_STREAM
23 uses CONFIG_ROM_STREAM_START
31 uses LB_CKS_RANGE_START
34 uses MAINBOARD_PART_NUMBER
37 uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
38 uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
39 uses LINUXBIOS_EXTRA_VERSION
49 uses DEFAULT_CONSOLE_LOGLEVEL
50 uses MAXIMUM_CONSOLE_LOGLEVEL
51 uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
52 uses CONFIG_CONSOLE_SERIAL8250
53 uses CONFIG_CONSOLE_BTEXT
57 uses CONFIG_CONSOLE_VGA
58 uses CONFIG_PCI_ROM_RUN
59 uses K8_E0_MEM_HOLE_SIZEK
63 ## ROM_SIZE is the size of boot ROM that this board will use.
65 default ROM_SIZE=524288
68 ## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
70 default FALLBACK_SIZE=131072
77 ## Build code for the fallback boot
79 default HAVE_FALLBACK_BOOT=1
82 ## Build code to reset the motherboard from linuxBIOS
84 default HAVE_HARD_RESET=1
86 default HARD_RESET_BUS=1
87 default HARD_RESET_DEVICE=4
88 default HARD_RESET_FUNCTION=0
91 ## Build code to export a programmable irq routing table
93 default HAVE_PIRQ_TABLE=1
94 default IRQ_SLOT_COUNT=11
97 ## Build code to export an x86 MP table
98 ## Useful for specifying IRQ routing values
100 default HAVE_MP_TABLE=1
103 ## Build code to export a CMOS option table
105 default HAVE_OPTION_TABLE=1
108 ## Move the default LinuxBIOS cmos range off of AMD RTC registers
110 default LB_CKS_RANGE_START=49
111 default LB_CKS_RANGE_END=122
112 default LB_CKS_LOC=123
115 ## Build code for SMP support
116 ## Only worry about 2 micro processors
119 default CONFIG_MAX_CPUS=4
120 default CONFIG_MAX_PHYSICAL_CPUS=2
121 default CONFIG_LOGICAL_CPUS=1
124 default K8_E0_MEM_HOLE_SIZEK=0x100000
128 default CK804_DEVN_BASE=0
131 #default CONFIG_CONSOLE_BTEXT=1
134 default CONFIG_CONSOLE_VGA=1
135 default CONFIG_PCI_ROM_RUN=1
138 ## Build code to setup a generic IOAPIC
140 default CONFIG_IOAPIC=1
143 ## Clean up the motherboard id strings
145 default MAINBOARD_PART_NUMBER="Tyan"
146 default MAINBOARD_VENDOR="s2891"
147 default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x10f1
148 default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2891
151 ### LinuxBIOS layout values
154 ## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy.
155 default ROM_IMAGE_SIZE = 65536
158 ## Use a small 8K stack
160 default STACK_SIZE=0x2000
163 ## Use a small 16K heap
165 default HEAP_SIZE=0x4000
168 ## Only use the option table in a normal image
170 default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
173 ## LinuxBIOS C code runs at this location in RAM
175 default _RAMBASE=0x00004000
178 ## Load the payload from the ROM
180 default CONFIG_ROM_STREAM = 1
183 ### Defaults of options that you may want to override in the target config file
187 ## The default compiler
189 default CC="$(CROSS_COMPILE)gcc -m32"
193 ## Disable the gdb stub by default
195 default CONFIG_GDB_STUB=0
198 ## The Serial Console
201 # To Enable the Serial Console
202 default CONFIG_CONSOLE_SERIAL8250=1
204 ## Select the serial console baud rate
205 default TTYS0_BAUD=115200
206 #default TTYS0_BAUD=57600
207 #default TTYS0_BAUD=38400
208 #default TTYS0_BAUD=19200
209 #default TTYS0_BAUD=9600
210 #default TTYS0_BAUD=4800
211 #default TTYS0_BAUD=2400
212 #default TTYS0_BAUD=1200
214 # Select the serial console base port
215 default TTYS0_BASE=0x3f8
217 # Select the serial protocol
218 # This defaults to 8 data bits, 1 stop bit, and no parity
219 default TTYS0_LCS=0x3
222 ### Select the linuxBIOS loglevel
224 ## EMERG 1 system is unusable
225 ## ALERT 2 action must be taken immediately
226 ## CRIT 3 critical conditions
227 ## ERR 4 error conditions
228 ## WARNING 5 warning conditions
229 ## NOTICE 6 normal but significant condition
230 ## INFO 7 informational
231 ## DEBUG 8 debug-level messages
232 ## SPEW 9 Way too many details
234 ## Request this level of debugging output
235 default DEFAULT_CONSOLE_LOGLEVEL=8
236 ## At a maximum only compile in this level of debugging
237 default MAXIMUM_CONSOLE_LOGLEVEL=8
240 ## Select power on after power fail setting
241 default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"