3 uses USE_FALLBACK_IMAGE
4 uses HAVE_FALLBACK_BOOT
8 uses CONFIG_ROM_PAYLOAD
12 uses MAINBOARD_PART_NUMBER
13 uses LINUXBIOS_EXTRA_VERSION
22 uses ROM_SECTION_OFFSET
23 uses CONFIG_ROM_PAYLOAD_START
24 uses CONFIG_COMPRESSED_PAYLOAD_LZMA
35 uses DEFAULT_CONSOLE_LOGLEVEL
36 uses MAXIMUM_CONSOLE_LOGLEVEL
37 uses CONFIG_CONSOLE_SERIAL8250
41 uses CONFIG_UDELAY_TSC
42 uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
43 uses CONFIG_CONSOLE_VGA
44 uses CONFIG_PCI_ROM_RUN
47 default CONFIG_VIDEO_MB=8
50 ## ROM_SIZE is the size of boot ROM that this board will use.
51 default ROM_SIZE = 1024*1024
56 #default CONFIG_CONSOLE_VGA=1
57 #default CONFIG_PCI_ROM_RUN=0
59 ## Build code for the fallback boot
61 default HAVE_FALLBACK_BOOT=1
66 default HAVE_MP_TABLE=0
69 ## Build code to reset the motherboard from linuxBIOS
71 default HAVE_HARD_RESET=0
73 ## Delay timer options
75 default CONFIG_UDELAY_TSC=1
76 default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2=1
79 ## Build code to export a programmable irq routing table
81 default HAVE_PIRQ_TABLE=0
82 default IRQ_SLOT_COUNT=6
87 ## Build code to export a CMOS option table
89 default HAVE_OPTION_TABLE=0
92 ### LinuxBIOS layout values
95 ## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy.
96 default ROM_IMAGE_SIZE = 65536
97 default FALLBACK_SIZE = 131072
100 ## Use a small 8K stack
102 default STACK_SIZE=0x2000
105 ## Use a small 16K heap
107 default HEAP_SIZE=0x4000
110 ## Only use the option table in a normal image
112 #default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
113 default USE_OPTION_TABLE = 0
115 default _RAMBASE = 0x00004000
117 default CONFIG_ROM_PAYLOAD = 1
120 ## The default compiler
122 default CROSS_COMPILE=""
123 default CC="$(CROSS_COMPILE)gcc -m32"
127 ## The Serial Console
130 # To Enable the Serial Console
131 default CONFIG_CONSOLE_SERIAL8250=1
133 ## Select the serial console baud rate
134 default TTYS0_BAUD=115200
135 #default TTYS0_BAUD=57600
136 #default TTYS0_BAUD=38400
137 #default TTYS0_BAUD=19200
138 #default TTYS0_BAUD=9600
139 #default TTYS0_BAUD=4800
140 #default TTYS0_BAUD=2400
141 #default TTYS0_BAUD=1200
143 # Select the serial console base port
144 default TTYS0_BASE=0x3f8
146 # Select the serial protocol
147 # This defaults to 8 data bits, 1 stop bit, and no parity
148 default TTYS0_LCS=0x3
151 ### Select the linuxBIOS loglevel
153 ## EMERG 1 system is unusable
154 ## ALERT 2 action must be taken immediately
155 ## CRIT 3 critical conditions
156 ## ERR 4 error conditions
157 ## WARNING 5 warning conditions
158 ## NOTICE 6 normal but significant condition
159 ## INFO 7 informational
160 ## DEBUG 8 debug-level messages
161 ## SPEW 9 Way too many details
163 ## Request this level of debugging output
164 default DEFAULT_CONSOLE_LOGLEVEL=8
165 ## At a maximum only compile in this level of debugging
166 default MAXIMUM_CONSOLE_LOGLEVEL=8