3 uses USE_FALLBACK_IMAGE
4 uses HAVE_FALLBACK_BOOT
8 uses CONFIG_ROM_PAYLOAD
12 uses MAINBOARD_PART_NUMBER
13 uses LINUXBIOS_EXTRA_VERSION
22 uses ROM_SECTION_OFFSET
23 uses CONFIG_ROM_PAYLOAD_START
24 uses CONFIG_COMPRESSED_PAYLOAD_LZMA
25 uses CONFIG_PRECOMPRESSED_PAYLOAD
36 uses DEFAULT_CONSOLE_LOGLEVEL
37 uses MAXIMUM_CONSOLE_LOGLEVEL
38 uses CONFIG_CONSOLE_SERIAL8250
42 uses CONFIG_UDELAY_TSC
45 ## ROM_SIZE is the size of boot ROM that this board will use.
46 default ROM_SIZE = 512*1024
53 ## Build code for the fallback boot
55 default HAVE_FALLBACK_BOOT = 1
60 default HAVE_MP_TABLE = 0
63 ## Build code to reset the motherboard from linuxBIOS
65 default HAVE_HARD_RESET = 0
68 ## Build code to export a programmable irq routing table
70 default HAVE_PIRQ_TABLE = 1
71 default IRQ_SLOT_COUNT = 11
74 ## Build code to export a CMOS option table
76 default HAVE_OPTION_TABLE = 0
79 default CONFIG_IDE = 1
82 ### LinuxBIOS layout values
85 ## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy.
86 default ROM_IMAGE_SIZE = 65536
87 default FALLBACK_SIZE = 131072
90 ## Use a small 8K stack
92 default STACK_SIZE=0x2000
95 ## Use a small 16K heap
97 default HEAP_SIZE=0x4000
100 ## Only use the option table in a normal image
102 #default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
103 default USE_OPTION_TABLE = 0
105 default _RAMBASE = 0x00004000
107 default CONFIG_ROM_PAYLOAD = 1
110 ## The default compiler
112 default CROSS_COMPILE=""
113 default CC="$(CROSS_COMPILE)gcc -m32"
117 ## The Serial Console
120 # To Enable the Serial Console
121 default CONFIG_CONSOLE_SERIAL8250=1
123 ## Select the serial console baud rate
124 default TTYS0_BAUD=115200
125 #default TTYS0_BAUD=57600
126 #default TTYS0_BAUD=38400
127 #default TTYS0_BAUD=19200
128 #default TTYS0_BAUD=9600
129 #default TTYS0_BAUD=4800
130 #default TTYS0_BAUD=2400
131 #default TTYS0_BAUD=1200
133 # Select the serial console base port
134 default TTYS0_BASE=0x3f8
136 # Select the serial protocol
137 # This defaults to 8 data bits, 1 stop bit, and no parity
138 default TTYS0_LCS=0x3
141 ### Select the linuxBIOS loglevel
143 ## EMERG 1 system is unusable
144 ## ALERT 2 action must be taken immediately
145 ## CRIT 3 critical conditions
146 ## ERR 4 error conditions
147 ## WARNING 5 warning conditions
148 ## NOTICE 6 normal but significant condition
149 ## INFO 7 informational
150 ## DEBUG 8 debug-level messages
151 ## SPEW 9 Way too many details
153 ## Request this level of debugging output
154 default DEFAULT_CONSOLE_LOGLEVEL=9
155 ## At a maximum only compile in this level of debugging
156 default MAXIMUM_CONSOLE_LOGLEVEL=9
158 default CONFIG_UDELAY_TSC=1