--- /dev/null
+uses HAVE_MP_TABLE
+uses HAVE_PIRQ_TABLE
+uses HAVE_ACPI_TABLES
+uses ACPI_SSDTX_NUM
+uses USE_FALLBACK_IMAGE
+uses USE_FAILOVER_IMAGE
+uses HAVE_FALLBACK_BOOT
+uses HAVE_FAILOVER_BOOT
+uses HAVE_HARD_RESET
+uses IRQ_SLOT_COUNT
+uses HAVE_OPTION_TABLE
+uses CONFIG_MAX_CPUS
+uses CONFIG_MAX_PHYSICAL_CPUS
+uses CONFIG_LOGICAL_CPUS
+uses CONFIG_IOAPIC
+uses CONFIG_SMP
+uses FALLBACK_SIZE
+uses FAILOVER_SIZE
+uses ROM_SIZE
+uses ROM_SECTION_SIZE
+uses ROM_IMAGE_SIZE
+uses ROM_SECTION_SIZE
+uses ROM_SECTION_OFFSET
+uses CONFIG_ROM_STREAM
+uses CONFIG_ROM_STREAM_START
+uses CONFIG_COMPRESSED_ROM_STREAM
+uses PAYLOAD_SIZE
+uses _ROMBASE
+uses XIP_ROM_SIZE
+uses XIP_ROM_BASE
+uses STACK_SIZE
+uses HEAP_SIZE
+uses USE_OPTION_TABLE
+uses LB_CKS_RANGE_START
+uses LB_CKS_RANGE_END
+uses LB_CKS_LOC
+uses MAINBOARD_PART_NUMBER
+uses MAINBOARD_VENDOR
+uses MAINBOARD
+uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses LINUXBIOS_EXTRA_VERSION
+uses _RAMBASE
+uses TTYS0_BAUD
+uses TTYS0_BASE
+uses TTYS0_LCS
+uses DEFAULT_CONSOLE_LOGLEVEL
+uses MAXIMUM_CONSOLE_LOGLEVEL
+uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_CONSOLE_SERIAL8250
+uses HAVE_INIT_TIMER
+uses CONFIG_GDB_STUB
+uses CONFIG_GDB_STUB
+uses CROSS_COMPILE
+uses CC
+uses HOSTCC
+uses OBJCOPY
+uses CONFIG_CHIP_NAME
+uses CONFIG_CONSOLE_VGA
+uses CONFIG_PCI_ROM_RUN
+uses HW_MEM_HOLE_SIZEK
+uses HW_MEM_HOLE_SIZE_AUTO_INC
+uses K8_HT_FREQ_1G_SUPPORT
+
+uses HT_CHAIN_UNITID_BASE
+uses HT_CHAIN_END_UNITID_BASE
+uses SB_HT_CHAIN_ON_BUS0
+uses SB_HT_CHAIN_UNITID_OFFSET_ONLY
+
+uses USE_DCACHE_RAM
+uses DCACHE_RAM_BASE
+uses DCACHE_RAM_SIZE
+uses DCACHE_RAM_GLOBAL_VAR_SIZE
+uses CONFIG_USE_INIT
+
+uses SERIAL_CPU_INIT
+
+uses ENABLE_APIC_EXT_ID
+uses APIC_ID_OFFSET
+uses LIFT_BSP_APIC_ID
+
+uses CONFIG_PCI_64BIT_PREF_MEM
+
+uses CONFIG_LB_MEM_TOPK
+
+uses CONFIG_AP_CODE_IN_CAR
+
+uses MEM_TRAIN_SEQ
+
+uses WAIT_BEFORE_CPUS_INIT
+
+###
+### Build options
+###
+
+##
+## ROM_SIZE is the size of boot ROM that this board will use.
+##
+default ROM_SIZE=524288
+
+##
+## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
+##
+#default FALLBACK_SIZE=131072
+#default FALLBACK_SIZE=0x40000
+
+#FALLBACK: 256K-4K
+default FALLBACK_SIZE=0x3f000
+#FAILOVER: 4K
+default FAILOVER_SIZE=0x01000
+
+#more 1M for pgtbl
+default CONFIG_LB_MEM_TOPK=2048
+
+##
+## Build code for the fallback boot
+##
+default HAVE_FALLBACK_BOOT=1
+default HAVE_FAILOVER_BOOT=1
+
+##
+## Build code to reset the motherboard from linuxBIOS
+##
+default HAVE_HARD_RESET=1
+
+##
+## Build code to export a programmable irq routing table
+##
+default HAVE_PIRQ_TABLE=1
+default IRQ_SLOT_COUNT=11
+
+##
+## Build code to export an x86 MP table
+## Useful for specifying IRQ routing values
+##
+default HAVE_MP_TABLE=1
+
+## ACPI tables will be included
+default HAVE_ACPI_TABLES=1
+## extra SSDT num
+default ACPI_SSDTX_NUM=1
+
+##
+## Build code to export a CMOS option table
+##
+default HAVE_OPTION_TABLE=1
+
+##
+## Move the default LinuxBIOS cmos range off of AMD RTC registers
+##
+default LB_CKS_RANGE_START=49
+default LB_CKS_RANGE_END=122
+default LB_CKS_LOC=123
+
+##
+## Build code for SMP support
+## Only worry about 2 micro processors
+##
+default CONFIG_SMP=1
+default CONFIG_MAX_CPUS=8
+default CONFIG_MAX_PHYSICAL_CPUS=4
+default CONFIG_LOGICAL_CPUS=1
+
+default SERIAL_CPU_INIT=0
+
+default ENABLE_APIC_EXT_ID=0
+default APIC_ID_OFFSET=0x8
+default LIFT_BSP_APIC_ID=1
+
+#CHIP_NAME ?
+default CONFIG_CHIP_NAME=1
+
+#memory hole size, 0 mean disable, others will enable the hole, at that case if it is small than mmio_basek, it will use mmio_basek instead.
+#2G
+#default HW_MEM_HOLE_SIZEK=0x200000
+#1G
+default HW_MEM_HOLE_SIZEK=0x100000
+#512M
+#default HW_MEM_HOLE_SIZEK=0x80000
+
+#make auto increase hole size to avoid hole_startk equal to basek so as to make some kernel happy
+#default HW_MEM_HOLE_SIZE_AUTO_INC=1
+
+#Opteron K8 1G HT Support
+default K8_HT_FREQ_1G_SUPPORT=1
+
+#VGA Console
+default CONFIG_CONSOLE_VGA=1
+default CONFIG_PCI_ROM_RUN=1
+
+#HT Unit ID offset, default is 1, the typical one
+default HT_CHAIN_UNITID_BASE=0xa
+
+#real SB Unit ID, default is 0x20, mean dont touch it at last
+default HT_CHAIN_END_UNITID_BASE=0x6
+
+#make the SB HT chain on bus 0, default is not (0)
+default SB_HT_CHAIN_ON_BUS0=2
+
+#only offset for SB chain?, default is yes(1)
+#default SB_HT_CHAIN_UNITID_OFFSET_ONLY=0
+
+#allow capable device use that above 4G
+#default CONFIG_PCI_64BIT_PREF_MEM=1
+
+##
+## enable CACHE_AS_RAM specifics
+##
+default USE_DCACHE_RAM=1
+default DCACHE_RAM_BASE=0xc8000
+default DCACHE_RAM_SIZE=0x08000
+default DCACHE_RAM_GLOBAL_VAR_SIZE=0x01000
+default CONFIG_USE_INIT=0
+
+default CONFIG_AP_CODE_IN_CAR=1
+default MEM_TRAIN_SEQ=1
+
+default WAIT_BEFORE_CPUS_INIT=1
+
+##
+## Build code to setup a generic IOAPIC
+##
+default CONFIG_IOAPIC=1
+
+##
+## Clean up the motherboard id strings
+##
+default MAINBOARD_PART_NUMBER="serengeti_cheetah"
+default MAINBOARD_VENDOR="AMD"
+default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x1022
+default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2b80
+
+###
+### LinuxBIOS layout values
+###
+
+## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy.
+default ROM_IMAGE_SIZE = 65536
+
+##
+## Use a small 8K stack
+##
+default STACK_SIZE=0x2000
+
+##
+## Use a small 32K heap
+##
+default HEAP_SIZE=0x8000
+
+##
+## Only use the option table in a normal image
+##
+default USE_OPTION_TABLE = (!USE_FALLBACK_IMAGE) && (!USE_FAILOVER_IMAGE )
+
+##
+## LinuxBIOS C code runs at this location in RAM
+##
+default _RAMBASE=0x00100000
+
+##
+## Load the payload from the ROM
+##
+default CONFIG_ROM_STREAM = 1
+
+#default CONFIG_COMPRESSED_ROM_STREAM = 1
+
+###
+### Defaults of options that you may want to override in the target config file
+###
+
+##
+## The default compiler
+##
+default CC="$(CROSS_COMPILE)gcc-3.4.5 -m32"
+default HOSTCC="gcc-3.4.5"
+
+##
+## Disable the gdb stub by default
+##
+default CONFIG_GDB_STUB=0
+
+##
+## The Serial Console
+##
+
+# To Enable the Serial Console
+default CONFIG_CONSOLE_SERIAL8250=1
+
+## Select the serial console baud rate
+default TTYS0_BAUD=115200
+#default TTYS0_BAUD=57600
+#default TTYS0_BAUD=38400
+#default TTYS0_BAUD=19200
+#default TTYS0_BAUD=9600
+#default TTYS0_BAUD=4800
+#default TTYS0_BAUD=2400
+#default TTYS0_BAUD=1200
+
+# Select the serial console base port
+default TTYS0_BASE=0x3f8
+
+# Select the serial protocol
+# This defaults to 8 data bits, 1 stop bit, and no parity
+default TTYS0_LCS=0x3
+
+##
+### Select the linuxBIOS loglevel
+##
+## EMERG 1 system is unusable
+## ALERT 2 action must be taken immediately
+## CRIT 3 critical conditions
+## ERR 4 error conditions
+## WARNING 5 warning conditions
+## NOTICE 6 normal but significant condition
+## INFO 7 informational
+## DEBUG 8 debug-level messages
+## SPEW 9 Way too many details
+
+## Request this level of debugging output
+default DEFAULT_CONSOLE_LOGLEVEL=8
+## At a maximum only compile in this level of debugging
+default MAXIMUM_CONSOLE_LOGLEVEL=8
+
+##
+## Select power on after power fail setting
+default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+
+### End Options.lb
+end
projects / coreboot.git / blobdiff